i9900
Series
Start Here
Easy Setup Instructions
Photo Printer
Install the Ink Tanks
and Load Paper
Connect the Printer
1
Unpack the Printer
2
Prepare the Printer
3
Install the Print Head
4
5
1
1
1
Peel back the orange tab and completely
remove the plastic wrapper from the Yellow
Ink Tank (BCI-6Y).
Carefully remove all items from the box.
Remove the print head from its package.
1
Remove the printer from the box by using
the plastic bag handle.
IMPORTANT: Be sure the printer is
off before continuing, or the computer
will attempt to install the printer
driver before the printer is ready.
Handle
USB Ports:
1
2
TURN THE PRINTER OFF.
Tear at notch to open
2
Connect one end of the USB cable
to the computer, the other to the
appropriate USB port on the printer.
Twist off and discard the orange protective cap.
N
OTE: To avoid spilling ink, never press on the
sides of an ink tank.
2
Remove the orange protective cap
from the print head.
If your computer and operating system
support USB 2.0 Hi-Speed, use the
top port. Otherwise, use the bottom port.
Protective Cap
i9900 Series
NOTE: Do not touch the print head nozzles
and the electrical contacts.
Photo Printer
2
Remove the shipping tape from the
front and back of the printer.
NOTE: The i9900 Series Photo Printer
is equipped with both USB 2.0 Hi-Speed
and USB ports. If you do not know your
USB version number, connect using
the lower port.
3 Insert the ink tank into the correct slot.
Do not switch port after installation.
(Refer to the color guide on the print head holder).
USB 2.0 Hi-Speed
Press down until the ink tank clicks into place.
Shipping Tape
IEEE 13
Print Head Nozzles
3
Plug the power cord into the back of the
printer and connect the other end to a
power outlet.
Documentation
and Software Kit
Electrical Contacts
click
USB Cable
4
Insert the remaining seven ink tanks into
their assigned slots.
IEEE 1394
3
Raise the gray lock lever on the printer.
USB Port
USB
i9900 Series Print Head
4
Press the POWER button. The printer
will initialize.
FireWire Port (for Mac Only):
1
2
POWER
Button
POWER
Lamp
TURN THE PRINTER OFF.
5
Close the front cover. Lift open the paper rest
and extend the paper output tray.
Connect one end of the FireWire cable
to the Macintosh, the other to the
FireWire port on the printer.
Paper Rest
4
Slide the print head into the holder.
The print head will rest at a slight angle.
Paper Output Tray
Power Cord
If your computer and operating system
support FireWire, use the Firewire port.
Otherwise, use the USB port.
Front Cover
NOTE: The printer will perform a print head
cleaning. Wait until the POWER lamp displays
a steady green light before proceeding.
5
Open the front cover. The print head holder
automatically moves to the center. Remove
the protective tape.
IEEE 1394
Ink Tanks
6
Remove the packaging from inside the paper
guide. Pinch the paper guide and slide it to
the left. Load the printer with a few sheets of
blank paper, then slide the paper guide
toward the left edge of the paper.
BCI-6R Red
BCI-6PM Photo Magenta
BCI-6BK Black
BCI-6G Green
5
Lower the lock lever and press it down
until it clicks into place.
FireWire Cable
click
Protective Tape
Serial Number
FireWire Port
Paper
Guide
BCI-6C Cyan
BCI-6PC Photo Cyan
BCI-6M Magenta
BCI-6Y Yellow
Continue with Step 6
on side two.
6
Write down the serial number located to
the right of the print head holder . You will
need this later to register the product.
Download from Www.Somanuals.com. All Manuals Search And Download.
6
Windows® Printer Driver Installation and Print Head Alignment
6
Macintosh® Printer Driver Installation and Print Head Alignment
NOTE: For Mac OS 8.6 to 9.x printer driver instructions,
refer to the "Appendix" of the Quick Start Guide.
1
6
12
Be sure to TURN THE PRINTER OFF
before continuing.
When the "Printer Connection" window
appears, TURN THE PRINTER ON. The
software will begin identifying the printer
port being used.
Start the print head alignment procedure.
1
d. Click the down-arrow to select
Test Print. Click the Print Head
Alignment icon and follow the
on-screen instructions.
Turn on your Mac and your printer and
insert the “Setup Software & User's Guide”
CD-ROM.
a. For Windows XP click Start, select
Control Panel, Printers and
Other Hardware, then Printers
and Faxes.
POWER
Button
NOTE: Log on as an Administrator
before continuing
.
POWER
Lamp
b. Right-click the i9900 icon,
then click Printing Preferences.
2
Double-click the CD-ROM icon, then theMac
OS X folder, then the Printer Driver folder.
NOTE: For Windows 98/Me/2000
click Start, then select Settings,
Printers. Right-click the i9900
icon, then click Properties.
IMPORTANT: If your computer cannot
detect a printer port, click Help and
refer to the online instructions.
NOTE: For Windows® XP or Windows
2000, log on to Windows as a member of the
Administrators group before continuing.
e. Look at the printed patterns and input
the values for each pattern that
shows no flaws (least number of
white stripes). Then click Send.
c. Click the Maintenance tab, then
7
Follow the on-screen instructions to install
the remaining software.
click on the Print Head Alignment icon.
IMPORTANT: If you see the Found New
Hardware Wizard, click Cancel.
3
Double-click the i9900 250.pkg icon,
then follow the on-screen instructions.
i9900
f. The rest of the print head alignment
process will take place automatically.
Ensure paper is loaded and follow the
on-screen instructions. This process
will take a few minutes.
When the "Installation Results" screen
appears, click OK.
8
9
NOTE: When the "Authenticate" screen appears,
enter your administrator name and password.
If you do not know your administrator name
d. When asked to start the print
head alignment, click Print Head
Alignment and follow the on-screen
instructions.
Register your product to ensure product
support. Follow the on-screen instructions.
2
or password, click
, then follow the
Close any open software applications,
(including anti-virus, computer security and
other software) then insert the “Setup
Software & User’s Guide” CD-ROM. The
setup program should run automatically.
7
Click Quit to exit the BJ Printer Utility. Print
head alignment is now complete.
on-screen instructions.
4
5
When the message "The software was
successfully installed" appears, click
Restart.
8
Access your CD-ROM again. From the
Application folder on the CD-ROM, double-
click on the software to be installed.
10
11
When the "Print Head Alignment" screen
appears, click Next. You will need to align
your print head after you restart your
computer.
NOTE: If the setup program does not run,
click Start, then Run, then type
D:\msetup.exe, where D is your CD-ROM
drive.
When a message asking you to align the
print head appears, click OK.
Click Next when you see the "On-Screen
Manual" screen. When the "Installation
completed successfully" screen appears,
click Restart.
e. Look at the printed patterns and
input the values for each pattern that
shows no flaws (least number of
white stripes). Then click OK.
3
When the main menu appears, click Easy
Install.
6
Start the print head alignment procedure.
9
Follow the on-screen instructions. When the
“Installation has finished” screen appears,
click OK.
a. Double-click the Macintosh HD icon,
then Applications folder. Double-click
the Utilities folder, then the Print Center
icon.
10
Register your product to ensure product
support. Double-click on the Product
Registration icon, found in the Mac OS X
folder. Follow the on-screen instructions.
NOTE: For Mac OS X 10.3.x select the
Printer Setup Utility icon.
b. When the Printer List screen appears,
select i9900, then click the Configure
icon.
When the "Easy Install" screen appears,
4
click Install.
f. The rest of the print head alignment
process will take place automatically.
Ensure paper is loaded and follow the
on-screen instructions. This process
will take a few minutes.
NOTE: For Mac OS X 10.3.x select the
Utility icon.
c. Select i9900 and click Maintenance.
13
Click OK to exit the Maintenance tab.
Print head alignment is now complete.
5
Read the License Agreement, then
click I accept, then Next to continue.
The installation process will start.
Part no. QA7-3190-V01 © 2004 Canon U.S.A., Inc. Canon is a Registered Trademark of Canon Inc. All other products and brand names are registered trademarks or trademarks of their respective owners. Specifications subject to change without notice. P-i9900-ESI-1103 Printed in Thailand.
Download from Www.Somanuals.com. All Manuals Search And Download.
|