CD-R Document Recorder
INSTRUCTIONS
Hardware Version
Please read this manual before operating the document recorder. After you
finish reading this manual, store it in a safe place for future reference.
Download from Www.Somanuals.com. All Manuals Search And Download.
FCC REGULATIONS (For 120V/220-240V models)
CD-R Document Recorder, Model M11050
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Use of shielded cable is required to comply with class B limits in Subpart B of Part 15 of FCC Rules.
Do not make any changes or modifications to the equipment unless otherwise specified in the manual. If such changes
or modifications should be made, you could be required to stop operation of the equipment.
Canon U.S.A. Inc.
One Canon Plaza, Lake Success NY 11042, U.S.A.
Tel No. (516)328-5600
RADIO INTERFERENCE REGULATIONS (For 120V models)
This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus as set out
in the Interference-causing equipment standard entitled “Digital Apparatus”, ICES-003 of the Industry Canada.
RÉGLEMENT SUR LE BROUILLAGE RADIOÉLECTRIQUE (For 120V models)
Cet appareil numérique respecte les limites de bruits radioélectriques applicables aux appareils numériques de Classe B
prescrites dans la norme sur le matériel brouilleur: “Appareils Numériques”, NMB-003 édictée par l’Industrie Canada.
Für EMVG
Dieses Produkt ist zum Gebrauch im Wohnbereich, Geschäfts-und Gewerbebereich sowie in Kleinbetrieben
vorgesehen.
Für 3. GSGV
Maschinenlärminformationsverordnung 3. GSGV, 18.01.1991: Der höchste Schalldruckpegel beträgt 70 dB(A) oder
weniger gemäß EN 27779.
Hg
LAMP(S) INSIDE THIS PRODUCT CONTAIN MERCURYAND MUST BE
RECYCLED OR DISPOSED OF ACCORDING TO LOCAL, STATE OR FEDERAL LAWS.
CAUTION
Use of controls or adjustments or performance of
procedures other than those specified herein may
result in hazardous radiation exposure.
Laser Diode Properties
Material: AlGaAs
Wavelength: 780-787nm
Emission Duration: Continuous
Laser Output Power
Objective lens Max emission light output Power
: 1.2mW(CW)(Read)
: min 77mW(Pulse)(Write)
Laser Diode Optical output
: 100mW(CW)
: 200mW(Pulse)
DHHS Class: Class1
ADVARSEL
USYNLIG LASERSTRÅLING VED ÅBNING.
UNDGÅ UDSAETTELSE FOR STRÅLING.
Download from Www.Somanuals.com. All Manuals Search And Download.
VAROITUS
LAITTEEN KÄYTTÄMINEN MUULLA
KUIN TÄSSÄ KÄYTTÖOHJEESA
MAINITULLA TAVALLA SAATTAA
ALTISTAA KÄYTTÄJÄN
TURVALLISUUSLUOKAN 1
YLITTÄVÄLLE NÄKYMÄTTÖMÄLLE
LASERSÄTEILYLLE.
VARNING
OM APPARATEN ANVÄNDS PÅ ANNAT
SÄTT ÄN I DENNABRUKSANVISNING
SPECIFICERATS, KAN ANVÄNDAREN
UTSÄTTAS FÖR OSYNLIG
LASERSTRÅLNING. SOM ÖVERSKRIDER
GRÄNSEN FÖR LASERKLASS 1.
CLASS 1 LASER PRODUCT
APPARAREIL A RAYONNEMENT LASAER DE CLASSE 1
LASER KLASSE 1
APPARECCHIO LASER DICLASSE 1
PRODUCTO LASER DE CLASE 1
APARELHO A LASER DE CLASSE 1
EN 60825-1:2001
Legal Notices
•
Copyright 2004 by CANON ELECTRONICS INC. All rights reserved. No part of this publication may be
reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer
language in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual, or otherwise,
without the prior permission of CANON ELECTRONICS INC.
•
•
•
•
•
Copyright of Barcode scanning software is attributed to Pixel Translations and its licensors.
Copyright of Japanese OCR and MICR scanning software is attributed to Canon Inc. and its licensors.
MAILOCX 1.81 COPYRIGHT 1998 WILL
The contents of this manual are subject to change without notice.
Every effort has been made to ensure the accuracy of information presented in this manual. However, Canon
Electronics Inc. and the subsidiaries on the back cover assume no responsibility for any errors or their consequences.
We do not assume any responsibility for damage resulting from operations regardless of the information above.
•
■ Pay attention to the following points when you use this machine to record documents:
• The recording of bank notes, coins and government issue stocks and bonds is illegal, and
is punishable.
• The recording of government issue passports, licenses issued by public authorities and
private bodies, permits, official documents and private documents is also punishable.
• Works such as books, music, paintings, woodblock prints, maps, drawings, films, and
photographs are used individually, within households, and in other equivalent limited
scopes. For this reason, use other than for recording is forbidden.
■ This machine uses lithium batteries. To protect the environment and natural resources,
contact your local authorized Canon dealer when you dispose of it.
Trademarks and Registered Trademarks
R
• Microsoft Windows is a registered trademark of Microsoft Corporation in the United States and in other
countries.
• Copyright of the CD-R writing software used by this product is attributed toAplix Corporation in
Japan and its licensors.
• This product uses Caere’s OCR engine. Caere is a registered trademark of Caere Corporation.
• Product names mentioned herein are for identification purposes only and may be trademarks and/or registered
trademarks of their respective companies.
Download from Www.Somanuals.com. All Manuals Search And Download.
END-USER LICENSE AGREEMENT FOR MICROSOFT SOFTWARE
•
•
You have acquired a device (“DEVICE”) which includes software licensed by Canon Electronics Inc. (CEI) from one or more
software licensors (“Canon Electronics Inc. Software Suppliers”). Such software products, as well as associated media, printed
materials, and “online” or electronic documentation (“SOFTWARE”) are protected by international intellectual property laws and
treaties. The SOFTWARE is licensed, not sold. All rights reserved.
IF YOU DO NOT AGREE TO THIS END USER LICENSE AGREEMENT (“EULA”), DO NOT USE THE DEVICE OR COPY
THE SOFTWARE. INSTEAD, PROMPTLY CONTACT Canon Electronics Inc. FOR INSTRUCTIONS ON RETURN OF THE
UNUSED DEVICE(S) FOR A REFUND. ANY USE OF THE SOFTWARE, INCLUDING BUT NOT LIMITED TO USE ON
THE DEVICE, WILL CONSTITUTE YOUR AGREEMENT TO THIS EULA (OR RATIFICATION OFANY PREVIOUS
CONSENT).
•
GRANT OF SOFTWARE LICENSE. This EULA grants you the following license:
ꢀ
You may use the SOFTWARE only on the DEVICE.
ꢀ
NOT FAULT TOLERANT. THE SOFTWARE IS NOT FAULT TOLERANT. Canon Electronics Inc. HAS INDEPEN-
DENTLY DETERMINED HOW TO USE THE SOFTWARE IN THE DEVICE, AND MS HAS RELIED UPON
Canon Electronics Inc. TO CONDUCT SUFFICIENT TESTING TO DETERMINE THAT THE SOFTWARE IS
SUITABLE FOR SUCH USE.
ꢀ
ꢀ
NO WARRANTIES FOR THE SOFTWARE. THE SOFTWARE is provided “AS IS” and with all faults. THE
ENTIRE RISK AS TO SATISFACTORY QUALITY, PERFORMANCE, ACCURACY, AND EFFORT (IN-
CLUDING LACK OF NEGLIGENCE) IS WITH YOU. ALSO, THERE IS NO WARRANTYAGAINST
INTERFERENCE WITH YOUR ENJOYMENT OF THE SOFTWARE OR AGAINST INFRINGEMENT. IF
YOU HAVE RECEIVED ANY WARRANTIES REGARDING THE DEVICE OR THE SOFTWARE, THOSE
WARRANTIES DO NOT ORIGINATE FROM, AND ARE NOT BINDING ON, MS.
No Liability for Certain Damages. EXCEPT AS PROHIBITED BY LAW, MS SHALL HAVE NO LIABILITY
FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL OR INCIDENTAL DAMAGES ARISING FROM OR IN
CONNECTION WITH THE USE OR PERFORMANCE OF THE SOFTWARE. THIS LIMITATION SHALL
APPLY EVEN IF ANY REMEDY FAILS OF ITS ESSENTIAL PURPOSE. IN NO EVENT SHALL MS BE
LIABLE FOR ANY AMOUNT IN EXCESS OF U.S. TWO HUNDRED FIFTY DOLLARS (U.S.$250.00).
Limitations on Reverse Engineering, Decompilation, and Disassembly. You may not reverse engineer, decompile, or
disassemble the SOFTWARE, except and only to the extent that such activity is expressly permitted by applicable law
notwithstanding this limitation.
SOFTWARE TRANSFER ALLOWED BUT WITH RESTRICTIONS. You may permanently transfer rights under
this EULA only as part of a permanent sale or transfer of the Device, and only if the recipient agrees to this EULA. If
the SOFTWARE is an upgrade, any transfer must also include all prior versions of the SOFTWARE.
EXPORT RESTRICTIONS. You acknowledge that SOFTWARE is of US-origin. You agree to comply with all
applicable international and national laws that apply to the SOFTWARE, including the U.S. Export Administration
Regulations, as well as end-user, end-use and country destination restrictions issued by U.S. and other governments. For
Limited Use of Particular SOFTWARE Services. Provided that the DEVICE continues to comply with the terms of
the “Restricted Functionality” paragraph below, without limiting the number of computers or other electronic devices
that might connect to the DEVICE to access or utilize other software or SOFTWARE services on the DEVICE, you may
permit a maximum of ten (10) computers or other electronic devices to connect to the DEVICE to utilize the services of
the SOFTWARE for (a) file and print services, (b) internet information services, and/or (c) remote access (including
connection sharing). The ten (10) connection maximum includes any indirect connections made through “multiplexing”
or other software or hardware which pools or aggregates connections.
If you use the DEVICE to access or utilize the services or functionality of Microsoft Windows Server products (such as
Microsoft Windows NT Server 4.0 (all editions) or Microsoft Windows 2000 Server (all editions)), or use the DEVICE
to permit workstation or computing devices to access or utilize the services or functionality of Microsoft Windows
Server products, you may be required to obtain a Client Access License for the Device and/or each such workstation or
computing device. Please refer to the end user license agreement for your Microsoft Windows Server product for
additional information.
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
Restricted Deployment. The SOFTWARE is not designed or intended for use or resale in hazardous environments
requiring fail-safe performance, such as in the operation of nuclear facilities, aircraft navigation or communication
systems, air traffic control, or other devices or systems in which a malfunction of the SOFTWARE would result in
foreseeable risk of injury or death to the operator of the device or system, or to others.
Restricted Functionality. You are licensed to use the SOFTWARE to provide only the limited functionality (specific
tasks or processes) for which the DEVICE has been designed and marketed by Canon Electronics Inc.. This license
specifically prohibits any other use of the SOFTWARE, or inclusion of additional software programs or functions, on
the DEVICE. Subject to the terms of the “Limited Use of Particular Services” paragraph above, you may use the
SOFTWARE on the DEVICE to interact with other computers or electronic devices.
ꢀ
ꢀ
Maximum Number of Processors. The SOFTWARE may not be used by more than two (2) processors at any one
time on the DEVICE.
Remote Boot Feature. Your DEVICE may be enabled with a Remote Boot feature which includes Remote Boot
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Services tool. You may use the Remote Boot Installation Services tool only to deploy the SOFTWARE to
one or more DEVICEs on which you are licensed to run the SOFTWARE (i.e. DEVICEs to which the appropriate
Certificate of Authenticity is affixed). Please refer to the DEVICE documentation, if provided with your DEVICE, or
contact Canon Electronics Inc. for additional information.
ꢀ
Security Updates. Content providers are using the digital rights management technology (“Microsoft DRM”) contained
in this SOFTWARE to protect the integrity of their content (“Secure Content”) so that their intellectual property,
including copyright, in such content is not misappropriated. Owners of such Secure Content (“Secure Content Owners”)
may, from time to time, request MS, Microsoft Corporation or their subsidiaries to provide security related updates to the
Microsoft DRM components of the SOFTWARE (“Security Updates”) that may affect your ability to copy, display and/
or play Secure Content through Microsoft software or third party applications that utilize Microsoft DRM. You therefore
agree that, if you elect to download a license from the Internet which enables your use of Secure Content, MS, Microsoft
Corporation or their subsidiaries may, in conjunction with such license, also download onto your DEVICE such Security
Updates that a Secure Content Owner has requested that MS, Microsoft Corporation or their subsidiaries distribute. MS,
Microsoft Corporation or their subsidiaries will not retrieve any personally identifiable information, or any other
information, from your DEVICE by downloading such Security Updates.
ꢀ
NetMeeting/Remote Assistance/Remote Desktop Features. The SOFTWARE may contain NetMeeting, Remote
Assistance, and Remote Desktop technologies that enable the SOFTWARE or other applications installed on the Device
to be used remotely between two or more computing devices, even if the SOFTWARE or application is installed on only
one Device. You may use NetMeeting, Remote Assistance, and Remote Desktop with all Microsoft products; provided
however, use of these technologies with certain Microsoft products may require an additional license. For both
Microsoft products and non-Microsoft products, you should consult the license agreement accompanying the applicable
product or contact the applicable licensor to determine whether use of NetMeeting, Remote Assistance, or Remote
Desktop is permitted without an additional license.
ꢀ
ꢀ
Consent to Use of Data. You agree that MS, Microsoft Corporation and their affiliates may collect and use technical
information gathered in any manner as part of product support services related to the SOFTWARE. MS, Microsoft
Corporation and their affiliates may use this information solely to improve their products or to provide customized
services or technologies to you. MS, Microsoft Corporation and their affiliates may disclose this information to others,
but not in a form that personally identifies you.
Internet Gaming/Update Features. If the SOFTWARE provides, and you choose to utilize, the Internet gaming or
update features within the SOFTWARE, it is necessary to use certain computer system, hardware, and software informa-
tion to implement the features. By using these features, you explicitly authorize MS, Microsoft Corporation and/or their
designated agent to use this information solely to improve their products or to provide customized services or technolo-
gies to you. MS or Microsoft Corporation may disclose this information to others, but not in a form that personally
identifies you.
ꢀ
ꢀ
Internet-Based Services Components. The SOFTWARE may contain components that enable and facilitate the use of
certain Internet-based services. You acknowledge and agree that MS, Microsoft Corporation or their affiliates may
automatically check the version of the SOFTWARE and/or its components that you are utilizing and may provide
upgrades or supplements to the SOFTWARE that may be automatically downloaded to your Device.
Links to Third Party Sites. The SOFTWARE may provide you with the ability to link to third party sites through the
use of the SOFTWARE. The third party sites are not under the control of MS, Microsoft Corporation or their affiliates.
Neither MS nor Microsoft Corporation nor their affiliates are responsible for (i) the contents of any third party sites, any
links contained in third party sites, or any changes or updates to third party sites, or (ii) webcasting or any other form of
transmission received from any third party sites. If the SOFTWARE provides links to third party sites, those links are
provided to you only as a convenience, and the inclusion of any link does not imply an endorsement of the third party
site by MS, Microsoft Corporation or their affiliates.
ꢀ
Additional Software/Services. The SOFTWARE may permit Canon Electronics Inc., MS, Microsoft Corporation or
their affiliates to provide or make available to you SOFTWARE updates, supplements, add-on components, or Internet-
based services components of the SOFTWARE after the date you obtain your initial copy of the SOFTWARE (“Supple-
mental Components”).
•
If Canon Electronics Inc. provides or makes available to you Supplemental Components and no other EULA
terms are provided along with the Supplemental Components, then the terms of this EULA shall apply.
If MS, Microsoft Corporation or their affiliates make available Supplemental Components, and no other EULA
terms are provided, then the terms of this EULA shall apply, except that the MS, Microsoft Corporation or
affiliate entity providing the Supplemental Component(s) shall be the licensor of the Supplemental
Component(s).
•
Canon Electronics Inc., MS, Microsoft Corporation and their affiliates reserve the right to discontinue any Internet-based
services provided to you or made available to you through the use of the SOFTWARE.
This EULA does not grant you any rights to use the Windows Media Format Software Development Kit (“WMFSDK”)
components contained in the SOFTWARE to develop a software application that uses Windows Media technology. If
windowsmedia/sdk/wmsdk.asp, accept a separate license for the WMFSDK, download the appropriate WMFSDK, and
install it on your system.
Download from Www.Somanuals.com. All Manuals Search And Download.
Welcome!
Thank you for purchasing the Canon CD-4070NW.
Two manuals are provided for the Canon CD-4070NW: Instructions (Hardware Version) and
Instructions (Software Version). This manual describes how to operate the CD-4070NW
Hardware.
Instructions (Hardware Version) describes the general features of the CD-4070NW. It also
explains how to scan documents and troubleshoot problems, such as paper jams.
Instructions (Software Version) explains screen displays and how to use the touch panel.
Please read these manuals thoroughly before operating the document recorder in order to
familiarize yourself with its capabilities, and to make the most of its many functions. After
reading the manuals, store them in a safe place for future reference.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Read Me
To Ensure Safe Management of Recorded Data
1. Do not subject discs to shock.
If you subject a CD-R disc to shock while data is being written to it, the data currently being written
including data that is already on the disc can be lost, and other errors may occur. If this happens, the lost
data cannot be recovered. Canon cannot assume any responsibility for lost data. Therefore, please pay
careful attention to subjecting the document recorder to shock during operation and, in particular, during
writing to a CD-R disc.
2. Do not allow the label side of the CD-R to become dirty or scratched.
Data is recorded onto the label side of the CD-R. If the label side of the CD-R becomes dirty or scratched,
any data on the disc may be lost. Also, writing on the label side of the CD-R with a ballpoint pen or a
sharp instrument will damage the recording layer of the CD-R, and result in the data becoming unreadable.
In either case, it is impossible to retrieve data from a damaged disc. If you must write on the disc, always
use a felt-tip pen or a pen with a soft point. Also, please be careful when handling discs.
3. Make backups.
CD-R discs can store a large volume of information. Therefore, a scratch on the disc can result in a large
amount of data being lost. We strongly recommend making frequent backups using the disc copy function.
4. Prepare spare discs
Always keep at least one spare disc for backups, or if a disc becomes unusable.
5. Use only suitable discs.
Use only appropriate high-quality discs that are compatible with the CD-R document recorder drive. For
details, contact your local authorized Canon dealer.
6. Be careful when using CD-R discs that have been written onto by this document
recorder when used in other CD-R or CD-rewritable drives. If write operations are
performed on discs using other drives, there is a possibility that discs could become
unusable with the document recorder.
7. Always wait at least 10 seconds after turning the power OFF before you turn the
power back ON.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Read Me............................................................................................................................................ 2
Conventions ............................................................................................................................. 5
Chapter 1. Safety Precautions
To Ensure Safe Use of This Unit ............................................................................................. 5
Preparing a Location......................................................................................................... 5
Power Supply.................................................................................................................... 6
Moving the Document Recorder ...................................................................................... 7
Handling Precautions ............................................................................................................... 8
Disc Handling ................................................................................................................. 10
Chapter 2. Overview of the CD-4070NW
Features of the CD-4070NW ................................................................................................. 12
Barcodes (Optional)........................................................................................................ 13
Backup Management ...................................................................................................... 13
Web Search Function ...................................................................................................... 14
Packaging Contents ............................................................................................................... 15
Part Names and Functions ..................................................................................................... 16
Touch Panel............................................................................................................................ 19
Chapter 3. Getting Started
Connecting the Network Cable and Peripherals .................................................................... 20
Connecting the Power Cord ................................................................................................... 20
Turning the Power ON/OFF .................................................................................................. 21
Turning the Power ON.................................................................................................... 21
Turning the Power OFF .................................................................................................. 22
How to Insert/Eject Discs ...................................................................................................... 23
Inserting Discs ................................................................................................................ 23
Ejecting Discs ................................................................................................................. 25
Chapter 4. Using the CD-4070NW
Document Handling ............................................................................................................... 27
Preparing the Paper Feed and Document Eject Trays............................................................ 28
Setting the Document Eject Guide ................................................................................. 29
Document Feeding ................................................................................................................. 31
Patch Code Sheets.................................................................................................................. 35
Patch Code Pattern Functions......................................................................................... 35
Creating Patch Code Sheets............................................................................................ 36
Using Patch Code Sheets ................................................................................................ 36
Chapter 5. Clearing Paper Jams .............................................................................................. 39
Chapter 6. Cleaning
Cleaning the Exterior ............................................................................................................. 41
Cleaning the Touch Panel ...................................................................................................... 41
Cleaning the Scanning Glasses and Rollers........................................................................... 42
Chapter 7. Troubleshooting ..................................................................................................... 43
Power Does Not Turn ON .............................................................................................. 43
Cannot Operate the Document Recorder........................................................................ 43
Paper Does Not Feed Properly ....................................................................................... 43
Unexpected Scan Results................................................................................................ 44
Cannot Search for Documents ........................................................................................ 45
Cannot Search a Text String ........................................................................................... 45
Chapter 8. Appendix
Specifications......................................................................................................................... 46
Scanner ........................................................................................................................... 46
Network .......................................................................................................................... 47
Options ........................................................................................................................... 47
Consumables................................................................................................................... 47
External Dimensions....................................................................................................... 48
Index ...................................................................................................................................... 49
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Conventions
The following symbols are used in this manual to explain procedures, restrictions, handling precautions, and
instructions that should be observed for safety.
WARNING
Indicates a warning concerning operations that may lead to death or injury to persons if not
performed correctly. In order to use the machine safely, always pay attention to these warnings.
CAUTION
Indicates a caution concerning operations that may lead to injury to persons, or damage to
property if not performed correctly. In order to use the machine safely, always pay attention to
these cautions.
DISC SECURITY
Indicates a precaution that you must observe to ensure that data recorded on a disc is safely
managed.
IMPORTANT
Indicates operational requirements and restrictions. Be sure to read these items carefully in order
to operate the machine correctly, and to avoid damage to the machine.
NOTE
Indicates a clarification of an operation, or contains additional explanations for a procedure.
Reading these notes is highly recommended.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Precautions
Chapter 1
To Ensure Safe Use of This Unit
Be sure to read the safety precautions for the following items to ensure safe use of the document recorder.
Preparing a Location
The capabilities of document recorder might be affected by the environment in which it is installed. Make sure
that its location satisfies the following environmental conditions.
27.6" (700 mm)
● Be sure that there is enough space around the document recorder
for operation, maintenance and ventilation as shown in the
illustration below.
3.9"
(100 mm)
● The document recorder should not be exposed to direct sunlight.
If this is unavoidable, install heavy curtains on the windows.
● Do not locate the document recorder in dusty locations. Dust
entering the document recorder may adversely affect internal
components.
● Do not place the document recorder near locations subject to high
temperature and humidity (e.g., water faucets, water heaters,
humidifiers), or near locations subject to ammonia gas or other
corrosive gases, or paint thinner.
A A
M
I
N
MO
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1. Safety Precautions
● Choose a location free of vibrations and strong shocks.
● Do not place the document recorder in a location subject to sudden
changes in temperature. Condensation forming inside the
document recorder might impair scam image quality. Use the
document recorder in the following operating environment:
Room temperature
Relative humidity
10°C to 32.5°C (50°F to 90.5°F)
20% to 80% RH
10°C
32.5°C
● Never place the document recorder near equipment, such as
speakers, TVs or radios, that generate magnetic fields.
Power Supply
● Be sure to supply power only from a 120 V/220-240 V outlet or
an uninterruptible power source (UPS).
● Do not plug the unit into an outlet shared with another device.
When you use an extension cord, pay attention to the amperage
of the extension cord.
● Never place an object on top of or tread on the power cord.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1. Safety Precautions
● Never bundle the power cord or wrap the cord around an object,
such as a table leg.
● Do not tug on the power cord. When you unplug the power plug,
be sure to firmly hold it by its plug head and not pull it out by the
lead connected to the plug.
● Always wait at least 10 seconds after disconnecting the power
cord before you insert the power plug into the power outlet again.
● Keep the area around the power outlet free of obstructions.
● If you are not sure of something regarding your power supply,
contact your local authorized Canon dealer or power company.
Moving the Document Recorder
● When you move the document recorder hold it firmly with both
hands as illustrated. The document recorder weighs approximately
33.1 lb (15 kg).
● Take care not to drop the touch panel when carrying the document
recorder with the touch panel placed on the top.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1. Safety Precautions
Handling Precautions
WARNING
When you are working around the document recorder, follow these precautions to avoid the hazards of
fire and electrical shock:
■ Never install and operate the document recorder near flammable substances, such as alcohol and
paint thinner.
■ Never damage, break or modify the power cord, place heavy objects on the power cord, or tug or
unnecessarily bend the power cord.
■ Never grasp the plug when your hands are wet.
■ Do not connect this unit to a power outlet shared with another device.
■ Never bundle or tie the power cord. Connect the plug securely to the power source.
■ Use only the power cord provided with the document recorder.
■ Never attempt to disassemble or modify the document recorder.
■ Never use flammable aerosol products near the document recorder.
■ Before you clean the document recorder, turn the power OFF and disconnect the power cord from
the power outlet.
■ To clean the document recorder, use a firmly wrung soft cloth moistened with water or a neutral
detergent. Never use flammable substances, such as alcohol, paint thinner, or benzene.
■ If the document recorder exhibits abnormal symptoms, including abnormal sounds, smoke, heat or
smell, immediately disconnect the power plug from the power outlet. Then, contact your local
authorized Canon dealer immediately.
■ Do not drop, bump, or subject the unit to strong shock. If you suspect the document recorder has
been accidentally damaged, immediately turn the power OFF, disconnect the power cord from the
power outlet, and then contact your local authorized Canon dealer immediately.
■ Before you move the document recorder, always turn the power OFF and disconnect the power cord
from the power outlet.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1. Safety Precautions
CAUTION
■ Do not locate the document recorder at an unstable location, such as a rocky workbench, other
inclined surface, or at a location subject to vibration. Otherwise, the document recorder might fall
down and cause unexpected injury.
■ Do not block the air vents. Doing so might cause heat build-up inside the document recorder or a
fire.
■ Do not place cups, vases and other containers filled with water, clips, staples, necklaces, or other
metal objects on the document recorder. If these items spill or enter inside the document recorder,
they may cause a fire or electrical shock. If you accidentally spill something into the document
recorder, turn the power OFF, disconnect the power cord from the power outlet, and call for service
immediately.
■ Do not install the document recorder in locations subject to dust or humidity. This can cause a fire
or electrical shock.
■ Never place heavy objects on top of the document recorder. Otherwise, they might fall down and
cause unexpected injury.
■ Use only a power supply having the rated voltage. Do not use a power supply having a different
voltage. Otherwise, it may cause a fire or electrical shock.
■ When you remove the power cord, grip it by the plug head. Never attempt to disconnect the power
cord from the power outlet by pulling on the power cord. Otherwise, the power cord may become
damaged by exposure of the core leads or broken leads, and may cause a fire or electrical shock.
■ Keep the area around the power outlet clear of all obstacles so you can disconnect the power cord
easily at all times.
■ Do not spill water or flammable substances (alcohol, paint thinner, benzene, etc.) inside the
document recorder. Otherwise, they might cause a fire or electrical shock.
■ If you are not using the document recorder for an extended period of time, always disconnect the
power cord from the power outlet beforehand for safety.
■ Avoid wearing loose, baggy clothing when you operate the document recorder, and accessories that
may become caught on the document recorder during operation. Clothing or accessories may
become entangled in the document recorder, and lead to injury. Pay particular attention to neckties
and long hair. If clothing or accessories should become caught inside the document recorder,
immediately disconnect the power cord to stop the document recorder.
■ Handle paper carefully when you place documents or remove jammed paper. Otherwise, you may
suffer an unexpected injury, such as cutting your hand on the edge of the paper.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1. Safety Precautions
Disc Handling
The CD drive on the document recorder is a CD-rewritable drive. However, this system prohibits documents
recorded on discs from being deleted, and prohibits the use of CD-RW discs that allow data to be deleted. With
the document recorder only use 650/700 MB CD-R discs that comply with the Recordable Compact Disc
Security System Part II Standard (Orange Book).
DISC SECURITY
• Damaged discs whose data can no longer be read cannot be repaired. Canon assumes no liability for damaged discs.
• Never use scratched or chipped discs. Doing so might damage the document recorder or cause it to malfunction.
• Use only discs carrying the
mark on this unit. You cannot use discs carrying the
mark.
ReWritable
Recordable
Handling Precautions
● Do not drop or subject discs to shock.
● Do not subject discs to the direct sunlight.
● Do not touch the recording surface or the label surface of the
disc.
● Do not affix paper or tape on the recording surface or the label
surface.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1. Safety Precautions
● When you write on the label surface of the disc, use a soft
felt-tipped pen. Do not use hard-tip pens, such as ball-point
pens.
● Do not store discs in dusty locations or locations where they
may be subject to cigarette smoke.
● Do not use or store discs in a location where a humidifier is in
operation.
● When you store a disc, insert it in its case, and store the disc in
a safe place.
● If the disc surface becomes dirty with fingerprints, wipe it clean
with a soft, dry cloth from the center of the disc outwards.
● When you have finished using a disc, eject and insert it in its
case, and store the disc in a safe place.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Overview of the CD-4070NW
Chapter 2
Features of the CD-4070NW
The CD-4070NW is a high-speed document recorder that integrates a scanner unit, control unit, and recording
unit. Microsoft Windows XP is used as its operating system. Scanning has been made easy by combining
preinstalled document management software with a touch panel for its control unit. CD-R discs that comply
with the Recordable Compact Disc Security System Part II Standard (Orange Book) are used as the document
recorder’s recording medium. This allows you to search and display data that has been recorded on the CD-
4070NW on ISO9660 Level 3-compliant CD-ROM drives on personal computers.
Here is a summary of the outstanding features of CD-4070NW:
■ High-Speed Paper Feed
In spite of the document recorder’s small size, it can scan documents from business card size up to B4 size at
high speed (up to 40 A4 size documents ppm in the simplex mode).
■ High Durability
A highly durable design provides scanning for up to three million scans.
■ Automatic Document Size Detection
The size of the scanned document is automatically detected, and areas around the document are cropped.
This reduces the size of the document and saves storage space.
■ Color/Grayscale Support*
Documents can be scanned at 24-bit color and 256-level grayscale.
(*)When scanning at 24-bit color,
24-bit color scanning is supported only for the front side of the document. If 24-bit color is selected and then
both sides of a document are scanned, the back side is scanned at 256-level grayscale.
■ Dropout Color (Front Side Only)
This function lets you skip (“drop out”) a specific color when scanning.
■ Skew Correction
If the document is fed at a slant, the scanned image is straightened to correct this before saving.
■ Text Mode
Text mode enables documents marked in light pencil or with strong background tones to be scanned clearly.
■ Skip Blank Page
The Skip Blank Page function detects any blank pages that have been scanned, and automatically discards
the data.
■ 52x Writable High-Speed CD-R Drive
Supports high-speed writing onto CD-R discs at speeds of up to 52x. If the CD-R disc does not support high
speed writing, the write speed can be configured to a speed that is supported.
■ Patch Code Recognition
Enables documents to be split into separate files whenever pages that contain patch codes are detected.
■ Barcode (Optional) , MICR, and OCR Input Functions
Barcodes (optional), MICR fonts (E13B only), and characters on specific areas of the scanned image can be
read in and saved into fields. (See “Barcodes,” on p.13.)
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2. Overview of the CD-4070NW
■ Function for Creating PDF Files with Text Attached
When documents are recorded in PDF format, text extracted using the OCR function can be attached to and
saved with the PDF file.
■ Network Function
The document recorder can be connected to a network via its internal Ethernet card. When connected to a
network, data can be recorded in shared network folders and accessed directly without a CD-R by computers
on the network. In addition, registered images and text can be sent by email.
■ Backup Management Function
Data scanned with the CD-4070NW is backed up internally, and then written to the CD-R. Because the data
is backed up, duplicate copies of the same disc can be made, and data can be copied onto another disc if one
disc is damaged. (See “Backup Management,” on p.13.)
■ Web Search Function
Data backed up with the CD-4070NW can be searched, viewed and downloaded from network computers by
using a web browser. (See “Web Search Function,” on p.14.)
■ Uninterruptible Power Source (UPS) Support
The document recorder provides support for a UPS, so that even if power is suddenly lost while in use, your
important data is preserved without bringing the system down. For details on how to use a UPS, please
contact your local authorized Canon dealer.
Barcodes (Optional)
The barcode input assist function (See “Barcode (Optional), MICR, and OCR Input Functions,” on p.12.) is an
optional accessory. If you wish to use it, a service representative must install the barcode module. Please contact
your local authorized Canon dealer.
Backup Management
CD-R disc data generated by recording documents is backed up internally to the CD-4070NW, so multiple
copies of the same disc can be made, or a CD-R disc can be reburned if one is damaged.
The limit on the amount of data that can be backed up is governed by the capacity of the hard disk installed. At
the time of this writing (May 2004), the maximum amount of data that can be saved is equivalent to 46 CD-Rs,
although this specification may change in the future.
For information on backup management, see the “CD-R Document Recorder CD-4070NW Instructions (Software
Version).”
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2. Overview of the CD-4070NW
Web Search Function
The web search function enables the data backed up to the document recorder to be published over a network so
that it can be searched, viewed, and downloaded from other computers by using a web browser. The entire back
up data can be searched by keyword, so even high volume discs can be searched for documents. This capability
greatly reduces the labor involved in finding a particular document on high volume discs.
For information on the various web pages, refer to the online Help.
HELP
NOTE
The web search function needs to be configured for your network environment. Your local authorized Canon dealer will
configure or confirm operation of the web search function in the presence of your network administrator.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2. Overview of the CD-4070NW
Packaging Contents
Make sure that the package contains all of the components in the illustration below. If any component is missing,
contact your local authorized Canon dealer.
CD-4070NW
Document Eject Guide
Auxiliary Paper Support Plate
Instructions
(Hardware Version, Software Version)
CD-R (Disc for Recording)
Quick Reference Guide
1
2
Power Cord*
Warranty Card*
*1 The power cord varies according to country of purchase.
*2 For U.S.A. and Canada only.
● The package contents may change without notice.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2. Overview of the CD-4070NW
Part Names and Functions
This section describes the functions of each of the parts. Familiarize yourself with them before you connect the
document recorder.
■ Front View
Power Indicator
Lights when the power switch is ON.
Paper Feed Tray
External Interface
Connect a network cable, mouse,
keyboard, etc. (See “External Interface,”
on p.17, and “Connecting the Network
Cable and Peripherals,” on p.20.)
Power Switch
Touch Panel
(See “Touch Panel,” on p.18,
CD-R Drive
and “Touch Panel,” on p.19.)
■ Front View (with Paper Feed Tray Open)
Document Eject Tray Extension
Prevents ejected documents from
falling.
Document Eject Tray
Scanned documents are
ejected onto this tray.
Paper Feed Tray
Place the document to be
scanned on here.
Paper Feed Tray Extension
Air Vent
Pull this tray out if the document
B
4
A
4
L
T
R
hangs over the edge of the main
tray.
Paper Side Guides
Adjust to the width of the
document to be scanned.
CAUTION
Never block the air vents. Doing so might cause heat build-up inside the unit or a fire.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2. Overview of the CD-4070NW
■ External Interface
RJ-45 Network Connector
Connect a 10Base-T/100Base-TX
twisted pair cable here.
15 pin D-Sub Connector
Connect a VGA monitor here.
PS/2 Connector (Purple)
Connect a PS/2 keyboard here.
PS/2 Connector (Green)
Connect a PS/2 mouse here.
NOTE
The VGA monitor output resolution is 640 x 480 dpi.
■ Back View
Power Cord Connector
This is used for connecting the power cord
(supplied).
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2. Overview of the CD-4070NW
■ Touch Panel
Power Switch
Turns the power ON.
Touch Panel
Stand
Contrast Dial
Adjusts the screen contrast.
Reset Switch
Turns the power OFF when a malfunction
or emergency occurs.
■ CD-R Drive
CD Tray
Eject Button
Use when inserting a disc.
LED
Lights when the drive is being used.
NOTE
The unit disables discs from being ejected with the eject button. (See “Ejecting Discs,” on p.25.)
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2. Overview of the CD-4070NW
Touch Panel
The document recorder is operated via a touch panel screen. This screen can be operated by lightly touching the
buttons that are displayed on the screen.
NOTE
• Be sure to touch the touch panel only with your fingertip. Do not
touch it with sharp pointed objects, such as your fingernail or a
ball-point pen. Doing so might scratch the screen surface and
cause the screen to malfunction.
• When touching buttons, take care to touch only the required area.
Touching other areas on the screen may cause a malfunction.
• You can use the stands to adjust the angle of the touch panel.
• If a screen is not displayed when the power turns ON, or there is
no response by touching the touch panel, push a long, thin object,
such as the tip of 0.04” to 0.06” (1.0 mm to 1.5 mm) dia. gage wire,
into the hole of the reset switch to turn the power OFF, then wait
at least 10 seconds before turning the power back ON.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Started
Chapter 3
This chapter describes how to prepare the machine before using it with procedures for connecting cables,
turning the power ON/OFF, and inserting/removing discs.
Connecting the Network Cable and Peripherals
To use the CD-4070NW over a network, connect a 10Base-T/100Base-TX compliant network cable to the rear
of the scanner. Connect a mouse, keyboard, and monitor according to your preference.
Network Cable
(10Base-T/100Base-TX)
VGA Monitor
(640 x 480 dpi)
PS/2 Mouse
PS/2 Keyboard
IMPORTANT
• Connect a mouse and keyboard before turning the scanner ON.
• Your local authorized Canon dealer will configure or confirm the network settings in the presence of your network
administrator.
• A mouse and keyboard are required in order to configure the network environment and other settings.
Connecting the Power Cord
Connect the power cord provided with the document recorder to
the power connector on the rear of the document recorder, and
insert the power plug into the power outlet.
IMPORTANT
• Use only the power cord provided with the document recorder.
• When using an uninterruptible power source (UPS), insert the
power plug into that.
• Be sure to connect the power cord while the document recorder’s
power switch is in the OFF position.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3. Getting Started
Turning the Power ON/OFF
The section describes the procedure for turning the power ON or OFF.
Turning the Power ON
When the power is turned ON, the CD-4070NW application automatically starts up.
Press the power switch on the touch panel.
The power indicator on the center of the document recorder
lights green, and the document recorder is turned ON.
1
The Startup screen is displayed, followed by the Main
screen.
2
IMPORTANT
• Do not touch the document recorder or touch panel until the
Main screen is displayed.
• If at least 5 seconds have elapsed after turning the power on
and the touch panel still remains blank, press the reset switch
located at the rear of the toch panel. If after you turn the
power back ON again nothing is still displayed, please
contact your local authorized Canon dealer.
• For explanations of the screens, see to the “CD-R Document
Recorder CD-4070NW Instructions (Software Version).”
Startup Screen
Main Screen
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3. Getting Started
Turning the Power OFF
The document recorder is turned OFF when the application is terminated.
CAUTION
If you do not intend to use the document recorder for an extended period of time, always disconnect the power cord
from the power outlet beforehand for safety.
NOTE
• Always remove the CD-R disc before exiting the application.
• Always wait at least 10 seconds after turning the power OFF before you turn the power back ON.
Press [Quit] on the Main screen.
The <Quit> confirmation message is displayed.
1
Press [OK].
2
NOTE
If a disc is loaded, an <Error> message is displayed. Press
[OK] → [Eject] → [OK] → remove the disc → press [Quit] →
[OK].
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3. Getting Started
How to Insert/Eject Discs
This section describes how to insert and eject discs.
Inserting Discs
Press the eject button to open the CD drive.
1
NOTE
If a disc is already inserted, the CD drive will not open even if
you press the eject button. Press the [Eject] button on the
Main screen and remove the disc. (See “Ejecting Discs,” on p.
25.)
Place the disc in the CD tray with the label facing up.
2
DISC SECURITY
• When handling CD-R discs, never touch the label side.
• Data is recorded on the label side of the CD-R. If the label
side becomes dirty or scratched, any data on the disc may be
lost. If this happens, lost data cannot be recovered, so be
careful when handling discs.
Press the eject button, or lightly push the CD tray to close
it.
3
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3. Getting Started
The inserted disc is recognized.
The disc icon displayed in the top left of the display
changes according to the type of disc inserted.
4
The disc icon displayed in the upper left side of the screen changes as shown below according to the disc
that was inserted.
(Blank disc)
Today’s date is assigned as the initial value for the disc’s name. For details on how to change the disc
name, see the “CD-R Document Recorder CD-4070NW Instructions (Software Version).”
(Loaded disc)
The volume of data on the disc is displayed in blue.
(Protected or Locked disc)
You cannot write documents to a disc indicated by this icon.
(Abnormal disc)
The CD-4070NW cannot recognize or use this disc. Replace the disc with a different disc.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3. Getting Started
Ejecting Discs..........................................................................................
Use the touch panel to eject a CD-R disc.
DISC SECURITY
Recorded data that was backed up to the hard disk is written to the CD-R before the disc is ejected. Ejecting a disc can
take a few minutes or longer, depending on the amount of data that is being written to it. Do not touch the unit until
writing to the disc has completed normally.
Press [Eject] on the Main screen.
The Eject Disc screen is displayed.
1
NOTE
Do not use the eject button on the CD drive to eject a disc. The
document recorder disables discs from being ejected with the
eject button.
Press [OK].
2
Data that is not already written to the disc is now written.
NOTE
Selecting [Inhibit re-write] in the Eject Disc screen will
prevent data from being rewritten.
The tray opens when writing to the disc is finished.
3
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3. Getting Started
Remove the disc.
4
DISC SECURITY
• After ejecting a disc, insert it in its case and store in a safe
place.
• Damaged discs whose data can no longer be read cannot be
restored. Canon assumes no liability for damaged discs.
Press the eject button, or lightly push the CD tray to close
it.
5
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the CD-4070NW
Chapter 4
Document Handling
The CD-4070NW can accept a wide variety of document sizes, from business card and personal checks to legal
size. The specifications for a document are:
Width:
2.2” to 10.1” (55 mm - 257 mm)
2.8” to 10.1” (70 mm - 257 mm) with automatic size recognition
2.8” to 14.3” (70 mm - 364 mm)
Length:
Thickness: 0.0024” to 0.059” (0.06 mm - 0.15 mm) with automatic feed
0.0019” to 0.0079” (0.05 mm - 0.2 mm) with manual feed
Weight:
14 to 32 lb bond (52 - 128g/m2) with automatic feed
11 to 40 lb bond (42 - 157g/m2) with manual feed
Follow these guidelines when you prepare an document for scanning:
● To avoid paper jams, all the documents in a batch should be of the same size, thickness, and weight.
● Documents whose ink has not yet dried may cause a malfunction. Make sure that the ink has dried before the
original is scanned.
● Graphite from the surface of a document written in pencil may stain the scanning rollers. After scanning an
document written in pencil or some other sort of writing material, be sure to clean the scanning rollers.
● When recording both sides of documents made from thin paper, the back side might show through on the
recorded image. Check the image by previewing it and adjust the brightness before recording.
● To avoid paper jams, do not feed the following types of paper into the document recorder. Make a copy of
such originals for scanning.
Wrinkled or creased paper
Curled paper
Carbon paper
Coated paper
Onion skin or other thin paper
Torn paper
Stapled paper or paper
with clips
Paper punched with square holes
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4. Using the CD-4070NW
Preparing the Paper Feed Tray and Document Eject Trays
Hold the edge of the paper feed tray and open it.
1
Gently open the paper feed tray toward you.
2
CAUTION
Other than documents, do not place heavy objects on the
B
4
paper feed tray. Doing so may result in them falling
unexpectedly causing injury or damaging the document
recorder.
If you are going to scan long originals, pull out the paper
feed tray extension.
3
4
B
4
A
L
4
T
R
Hold the edge of the document eject tray extension and
open it.
B
4
A
L
4
T
R
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4. Using the CD-4070NW
Gently open the document eject tray extension toward you.
5
NOTE
Be sure to open the document eject tray extension. Otherwise,
ejected originals may fall down and cause paper jams.
B
4
A
L
4
T
R
IMPORTANT
After recording has finished and when not using the document
recorder, close the paper feed tray and document eject tray
extension to avoid damage to the document recorder.
Setting the Document Eject Guide
To avoid paper jams when scanning thin or long documents, set the document eject guide supplied with the
document recorder.
Hold the edge of the document eject tray extension and
open it.
1
B
4
A
L
4
T
R
Attach the auxiliary paper support plate to the document
eject tray extension.
2
B
4
A
L
4
T
R
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4. Using the CD-4070NW
Gently open the document eject tray extension toward you.
3
B
4
A
L
4
T
R
Attach the document eject guide to the document eject tray
extension in the order illustrated.
4
5
Install it so that the ( ) mark on the
guide is aligned with the ( ) mark on
the body.
B
4
A
4
L
T
R
To remove the document eject guide, follow the above
procedure in reverse.
NOTE
• After the original eject guide is set in place, the method of
scanning is the same as when you make regular scans.
However, note that particularly thick and rigid documents
may not stack on the extension easily. In this case, we
recommend removing the document eject guide before use.
• Before you close the document eject tray extension or paper
feed tray, be sure to remove the document eject guide.
B
4
A
L
4
T
R
B
4
A
L
4
T
R
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4. Using the CD-4070NW
Document Feeding
The document recorder provides three feeding methods: standard, automatic, and manual. The procedures for
using each are different.
This section explains the basic procedure for each feeding method. For information on each of the screens, see
the “CD-R Document Recorder CD-4070NW Instructions (Software Version).”
Standard Feeding: Records one document stack at a time.
After being initiated, recording ends when no more document pages remain in the paper
feed tray.
Automatic Feeding: Recording continues each time the sensor detects a document.
If the sensor detects a document after recording has been initiated and before it is
terminated, recording continues.
This enables high volume documents to be recorded in one run.
Manual Feeding:
Documents are recorded by loading one page at a time manually into the paper
feed tray.
Use when scanning documents made from paper that does not feed properly, paper that
is prone to cause paper jams, or from thin paper.
CAUTION
Avoid wearing loose, baggy clothing and accessories that may become caught on the document recorder during
operation. Clothing or accessories may become entangled in the document recorder, and lead to injury. Pay particular
attention to neckties and long hair. If clothing or accessories should become caught inside the document recorder,
immediately disconnect the power cord to stop the document recorder.
NOTE
To avoid tearing the document, jamming, or damaging the document recorder, remove all paper clips, staples or any
other type of fasteners from the document pages before you place them in the document recorder.
Press [Record] on the Main screen.
The Set recording name screen is displayed.
1
2
Press [Mode].
The Set recording mode screen is displayed.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4. Using the CD-4070NW
Press [More].
The More settings screen is displayed.
3
Select [Standard], [Manual], or [Auto] → press [OK] →
[OK].
4
The Set recording name screen is displayed.
NOTE
If [Manual] is selected, the paper feed tray exit raises ready
for manual feeding.
Standard and Automatic Feeding
Adjust the paper side guides to match the width of the
5
document you are going to scan. If you are recording
standard size documents, align the document with the
document positioning mark.
NOTE
To avoid paper jams, do not set the edge of the document in
the area ( ) shown in the illustration.
A4
LTR
B4
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4. Using the CD-4070NW
• The paper side guide is inscribed with a loading limit mark
). This mark indicates the total thickness of
(
approximately 100 sheets of plain paper for recording
(80 g/m2). Do not place documents above this mark.
Otherwise, this may result in a paper jam.
Place the document face up, then adjust the paper side
guides to match the width of the document.
6
7
Specify the recording name → press [Start].
For information on how to specify the recording name, see
“CD-R Document Recoder CD-4070NW Instructions
(Software Version).”
Recording starts.
NOTE
• If feeding stops while recording due to a system error or
paper jam, resolve the problem, confirm that the last
document page fed was correctly recorded, and then
continue recording.
• Take care that documents with low paper thickness do not
fall from the document eject tray.
When no more document pages remain.
If you selected [Standard] Feeding:
8
Recording ends when no more document pages remain, and
the document image is displayed.
If you selected [Auto] Feeding:
Recording is suspended. Recording continues if a
document is loaded and detected. Automatic feeding can be
repeated until you press [Abort].
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4. Using the CD-4070NW
Manual Feeding
Adjust the paper side guides to match the width of the
5
document you are going to scan. If you are recording
standard size documents, align the document with the
document positioning mark.
Specify the recording name → press [Start]. For
6
information on how to specify the recording name, see
“CD-R Document Recorder CD-4070NW Instructions
(Software Version).”
Place one sheet face up with the top inserted into the
document recorder. The sheet starts to feed immediately.
7
B
4
A
L
T
4
R
NOTE
Particularly thin documents or curled documents are
sometimes not fed successfully. If this happens, hold down the
leading edge of the document with your hand when placing
them for scanning, or make copies on a copier and feed the
copy into the document recorder.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4. Using the CD-4070NW
Load the next document.
Recording continues if a document is loaded and detected.
Manual feed can be repeated until you press [Abort].
8
Patch Code Sheets
Patch code sheets are sheets printed with “patch code” patterns on them. They enable documents to be
automatically segmented into files during continuous feeding without interrupting the recording operation. If a
patch code sheet is scanned and the patch code detected, the file is automatically segmented.
NOTE
For information on using patch code sheets, see the “CD-R Document Recorder CD-4070NW Instructions (Software
Version).”
Patch Code Pattern Functions
The following two patch codes work in different ways:
PATCH T (FILE A)
• When this pattern is detected on a patch code sheet, file segmentation occurs from the
next document.
• Sheets printed with this pattern are not included in the recorded document.
PATCH II (FILE B)
• When this pattern is detected on a patch code sheet, file segmentation occurs at this
sheet.
• Sheets printed with this pattern are included in the recorded document.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4. Using the CD-4070NW
Creating Patch Code Sheets
Make copies of the patch code patterns provided at the rear of this manual. Follow the guidelines below when
copying patch code patterns.
● Copy the patch code patterns onto paper of the same type as that of the document to be scanned. If the paper
thickness substantially differs, a feed error may occur.
● Copy patch code patterns ensuring that the copies maintain the same size and image density as that of the
document. If the copies are too light or dark, they may not be scanned properly.
● Copy patch code patterns so that they are positioned on the page within the detectable area specified below.
0.2" (5 mm)
Patch Code
0.2" (5 mm)
0.2"
(5 mm)
3.7" (94 mm)
(Range in which patch code
detection is enabled.)
Units: inches (units in parentheses are millimeters)
● Take care not to get patch code sheets dirty, especially within the detectable area. In order for the sheets to be
scanned properly, make sure they do not get folded or crumpled.
● If the image density is too light or dark, the patch code sheets may not be scanned properly.
Using Patch Code Sheets
Make a copy of the patch pattern printed on p.51. Make
sure the paper is the same size as that of the document to be
scanned. (See “Patch Code Sheets,” on p.35.)
1
Patch Code Sheet
Insert the patch code sheets before or between each
document.
2
Insert the patch code sheets before
the first page of each document
where file segmentation should occur.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4. Using the CD-4070NW
Press [Record] on the Main screen.
The Set recording name screen is displayed.
3
4
5
6
Press [Mode].
The Set recording mode screen is displayed.
Press [More].
The More Settings screen is displayed.
Specify the Batch Separation, settings → press [OK].
The Set recording name screen is displayed.
NOTE
Selecting [Manual] for [Paper supply] disables segmentation
using patch sheets.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4. Using the CD-4070NW
Place the document face up into the paper feed tray.
7
B
4
A
L
4
T
R
Specify the recording name → press [Start].
8
Recording starts, and files are segmented whenever a patch
code is detected on a page. For information on how to
specify the recording name, see “CD-R Document
Recorder CD-4070NW Instructions (Software Version).”
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Clearing Paper Jams
Chapter 5
This chapter describes how to clear paper jams that may occur during use.
CAUTION
Handle paper carefully when you remove jammed paper. Otherwise, you may suffer an unexpected injury, such as
cutting your hand on the edge of the paper.
Remove the documents on the document eject tray.
1
Close the document eject tray extension if it is open.
2
If the document eject guide is installed, there is no need to
remove it and close the document eject tray extension.
Proceed to the next step.
B
4
A
L
4
T
R
Raise the top of the document feeder until it locks in the
open position.
3
B
4
A
L
4
T
R
B
4
A
L
4
T
R
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5. Clearing Paper Jams
Remove the jammed paper from inside the document
recorder.
4
■ If a paper jam occurs at the beginning of scanning:
B
4
A
4
L
T
R
■ If a paper jam occurs at the end of scanning:
NOTE
Do not unnecessarily tug on the jammed paper. Remove it
carefully. If the paper becomes ripped, be sure to remove any
remaining paper scraps in the document recorder.
Grasp the top of the document feeder and push it down
gently into the original position.
5
6
B
4
A
4
L
T
R
Push down on top of the document feeder until you hear it
lock into the closed position.
NOTE
After the problem is resolved, confirm that the last page was
recorded before continuing.
A
L
4
T
R
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Cleaning
Chapter 6
To ensure high-quality image scanning, regularly clean your CD-4070NW as described below.
CAUTION
• For safety, always quit the CD-4070NW and unplug the power cord before cleaning the document recorder.
• Never clean the document recorder with any kind of organic solvent, such as paint thinner or alcohol. Otherwise, the
document recorder’s exterior may be deformed, discolored, or melt. This may also cause a fire or electrical shock.
Cleaning the Exterior
Clean off any dirt on the document recorder’s exterior using a
firmly wrung, soft cloth moistened with water or a neutral
detergent. Then wipe dry with a clean, dry, soft cloth.
Cleaning the Touch Panel
■ Clean the edges and rear of the touch panel using a firmly
wrung, soft cloth moistened with water or a neutral
detergent. Then wipe dry with a clean, dry, soft cloth.
■ Clean off any dirt on the touch panel using a firmly
wrung, soft cloth moistened with water. Wipe lightly
taking care not to apply pressure to the surface of the
touch panel.
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6. Cleaning
Cleaning the Scanning Glasses and Rollers
If the scanning glass and rollers are dirty, recorded images may include lines and important original documents
may be marked. For this reason, periodically clean these parts.
Close the document eject tray extension if it is open.
1
B
4
A
L
4
T
R
Raise the top of the document feeder until it locks in the
open position.
2
B
4
A
L
4
T
R
B
4
A
L
4
T
R
Use a clean, dry, soft cloth to wipe the scanning glasses
3
(areas illustrated by
).
CAUTION
• Be sure to clean both scanning glasses, the one below and the
one above.
Never spray cleaning agents or water directly on the
scanning glasses. Otherwise, precision equipment, such as
the light source, may become damaged.
42
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6. Cleaning
Wipe the rollers (areas illustrated by
) with a firmly
4
wrung, soft cloth moistened with water. Turn all the rollers
in the directions shown in the illustration at 1, 2, and 3 as
you wipe them clean. Then wipe dry with a clean, dry, soft
cloth.
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Chapter 7
This chapter explains the action to take if there is a problem when using the document recorder.
Refer to the pages below depending on the type of problem you are having.
Power Does Not Turn ON ......................................................... p. 44
Cannot Operate the Document Recorder................................ p. 44
Paper Does Not Feed Properly ................................................. p. 44
Unexpected Scan Results .......................................................... p. 45
Cannot Search for Documents.................................................. p. 45
Cannot Search a Text String ..................................................... p. 45
If these suggestions do not remedy the problem, please contact your local anthorized Canon dealer.
Power Does Not Turn ON
Confirm the following:
● Is the power indicator lit? (See “Turning the Power ON,” on p.21.)
● Is the power cord firmly connected to the document recorder? (See “Connecting the Power Cord,” on p.20.)
● Is the power cord firmly inserted into the power outlet? (See “Connecting the Power Cord,” on p.20.)
NOTE
If the power indicator is lit but the touch panel is blank, press the reset switch located at the rear of the touch panel to
turn the power OFF, then wait at least 10 seconds before turning the power back ON. If nothing is still displayed, please
contact your local authorized Canon dealer.
Cannot Operate the Document Recorder
Press the reset switch located at the rear of the touch panel to turn the power OFF in the following situations:
(See “Touch Panel,” on p.19.)
● If the touch panel cannot be used due to a system error, for example
● If the touch panel display freezes and/or access to the CD-R drive (LED lights) takes a long time
● Pressing [Quit] does not turn the document recorder OFF.
NOTE
Always wait at least 10 seconds after turning the power OFF before you turn the power back ON.
Paper Does Not Feed Properly
Paper may not feed properly due to the following causes. Confirm each possible cause and take
the action given as appropriate.
Cause: You tried to scan in a document size, thickness, or weight that the document
recorder cannot handle.
Action: Confirm the document size, thickness, and weight. (See “Document Handling” on
p.27.)
Cause: The scanner rollers inside the unit are dirty or need replacing.
Action: For details on how to clean the rollers, see “Cleaning the Scanning Glasses and Rollers,”
on p.42. If the rollers need replacing, please contact your local authorized Canon
dealer.
For details on how to remove jammed documents, see “Clearing Paper Jams,” on p.39.
44
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 7. Troubleshooting
Unexpected Scan Results
Scanning problems, such as scanned images that are unclear, contain lines, or are dirty, might
be due to the following causes. Confirm each possible cause and take the appropriate action.
Cause: The scanning glasses and rollers inside the unit are dirty.
Action: For details on how to clean the scanning glasses and rollers, see “Cleaning the Scanning
Glasses and Rollers,” on p.42.)
Cause: The scan settings are inappropriate.
Action: Check the brightness and other settings on the settings screen. For example, if a
document will not scan at all, it is likely that the brightness setting is too high. If the
scan results seem far too black, the brightness setting may be too low.
Cause: The system is not functioning properly.
Action: If scanning is still not performed correctly even when the scan settings are properly
configured, the system may not be functioning properly. Please contact your local
authorized Canon dealer.
Cannot Search for Documents
If you cannot search for documents directly from the CD-4070NW or over the Web, possible
causes are given below. Confirm each possible cause and take the appropriate action.
Cause: You tried searching a disc just after inserting it in the CD-4070NW.
Action: The search index is still being built. Wait a while without operating the CD-4070NW
until this operation finishes.
Cause: The system was shut down uncleanly (e.g., due to a power outage while the
CD-4070NW was being used) causing the backup data index to be cleared.
Action: The backup data index is being rebuilt. Wait a while without operating the
CD-4070NW. Depending on the saved backup data, building the backup data index
may take at least 30 minutes.
NOTE
The CD-4070NW search function uses the operating system's indexing service. Therefore, when trying
to search a disc just after inserting it when the index was cleared (e.g., due to a power outage), it is
necessary to wait until the index finishes being built.
Indexes are rebuilt automatically while the CD-4070NW is in standby mode. No message is displayed
indicating indexes are being rebuilt, so do not operate the CD-4070NW while waiting.
Cannot Search a Text String
When text searching, some strings cannot be correctly searched for. Try shortening the string.
45
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Chapter 8
Specifications
Scanner
Type
Desktop image scanner and CD-R document recorder
Windows XP Embedded
Operating System
Scanning Document Specifications:
Width:
2.2" to 10.1" (55 mm to 257 mm)
2.8" to 10.1" (70 mm to 257 mm) with automatic size detection
2.8" to 14.3" (70 mm to 364 mm)
Length:
Thickness: 0.0024" to 0.059" (0.06 mm to 0.15 mm) with automatic feeding
0.0019" to 0.0079" (0.05 mm to 0.2 mm) with manual feeding
Weight:
14 to 32 lb bond (52 to 128 g/m2) with autoamtic feeding
11 to 40 lb bond (42 to 157 g/m2) with manual feeding
Document Feeding Method:
Scanning Method
Light Source
Standard/Automatic/Manual
Contact sensor
LED
Scanning Side
Simplex/Duplex
Scanning Modes
Black and white, text enhanced, error diffusion, grayscale, color
(front side only)
Scanning Resolution
Black and White, Grayscale: 300 x 300 dpi/300 x 150 dpi/240 x 240 dpi/200 x 200 dpi
Color: 200 x 200 dpi/100 x 100 dpi
Scanning Speed (Document Size: LTR/A4)
LTR
A4
Black and White: Simplex:
300 x 150 dpi 43 pages/minute 42 pages/minute
200 x 200 dpi 32 pages/minute 32 pages/minute
240 x 240 dpi 27 pages/minute 26 pages/minute
300 x 300 dpi 21 pages/minute 21 pages/minute
Duplex:
300 x 150 dpi 87 sides/minute
200 x 200 dpi 65 sides/minute
240 x 240 dpi 54 sides/minute
300 x 300 dpi 43 sides/minute
85 sides/minute
64 sides/minute
54 sides/minute
43 sides/minute
Grayscale: Simplex:
Duplex:
200 x 200 dpi 31 pages/minute 30 pages/minute
240 x 240 dpi 26 pages/minute 25 pages/minute
300 x 300 dpi 21 pages/minute 20 pages/minute
200 x 200 dpi 50 sides/minute
240 x 240 dpi 36 sides/minute
300 x 300 dpi 22 sides/minute
48 sides/minute
35 sides/minute
23 sides/minute
Color: Simplex:
100 x 100 dpi 21 pages/minute 20 pages/minute
200 x 200 dpi 10 pages/minute 10 pages/minute
Duplex (the back side is scanned with grayscale):
100 x 100 dpi 35 pages/minute 34 pages/minute
200 x 200 dpi 15 pages/minute 15 pages/minute
46
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 8. Appendix
Amount of paper that can be
stacked in automatic feeder
10 mm stack, maximum
Display
8.4" color LCD
Touch panel
Method of Operation
Compatible Disks
650 MB/700 MB CD-R
(Recordable Compact Disc System Part II)
CD-R Write Speed
Other Functions
52x maximum (configurable)
Automatic document thickness adjustment, patch code
recognition for automatic file segmentation, web serch function, backup
management
Document Recorder Dimensions
With Trays Open:
With Trays Closed: 10.4" x 13.9" x 16.2" (H x W x D)
265 mm x 352 mm x 412 mm (H x W x D)
12.5" x 13.9" x 27.2" (H x W x D)
318 mm x 352 mm x 692 mm (H x W x D)
Panel Dimensions
With Stand Closed: 1.8" x 8.3" x 6.7" (H x W x D)
46.7 mm x 210.6 mm x 169 mm (H x W x D)
With Stand Open:
4.1" x 8.3" x 7.1" (H x W x D)
103 mm x 210.6 mm x 181 mm (H x W x D)
Weight
Approximately 33.1 lb (15 kg)
Power Supply
120 V AC, 60 Hz 0.7 A
220-240 V AC, 50/60 Hz 0.4 A
Noise
Not more than 65 dB
Operating Environment
Temperature: 10°C to 32.5°C (50°F to 90.5°F)
Humidity:
20% to 80% RH
Network
Network
Microsoft Windows Network compliant
10Base-T/100Base-TX compliant
TCP/IP
Interface
Protocol
IP address
Static IP address or automatically acquired (DHCP)
Options
Bar Code Module
Add on module for detecting bar codes.
Consumables
Exchange Roller Kit
This is a transport roller replacement kit. Please contact your local
authorized Canon dealer as they must actually perform the replacement.
Specifications are subject to change without notice.
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 8. Appendix
External Dimensions
Units: inches (units in parentheses are millimeters)
Cable length: approximately 39" (1000 mm)
27.2" (692 mm)
When the paper feed tray and paper feed
tray extension are open
18.8" (478 mm)
When the auxiliary paper
support plate is installed
16.2" (412 mm)
Touch Panel
(With Stand Extended)
Touch Panel
(With Stand Flat)
1.8" (46.7 mm)
7.1" (181 mm)
6.7" (169 mm)
48
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 8. Appendix
Index
Main screen .............................................. 21
Network cable .......................................... 20
Options ..................................................... 47
M
N
O
P
Air Vent .................................................... 16
Auxiliary paper support plate ................... 29
A
B
C
Backup management ................................ 13
Barcodes ................................................... 13
Packaging ................................................. 15
Paper feed tray.................................... 16, 28
Paper feed tray extension ......................... 16
Paper jams ................................................ 39
Paper side guides ...................................... 16
Patch code
Patch code sheets .............................. 35
Patch code pattern ............................. 35
Power code ............................................... 20
Power indicator ........................................ 16
Power switch ...................................... 16, 18
Preparing a location.................................... 5
CD-R drive ......................................... 16, 18
CD tray ..................................................... 18
Cleaning ................................................... 41
Exterior.............................................. 41
Rollers ............................................... 42
Scanning glasses ............................... 42
Touch panel ....................................... 41
Connecting peripherals............................. 20
Specifications .................................... 46
Contrast dial ............................................. 18
Consumables ............................................ 47
Disc
D
Reset switch.............................................. 18
R
S
Handling............................................ 10
Inserting discs ................................... 23
Ejecting discs .................................... 25
Document ................................................. 27
Document eject guide ............................... 15
Document eject tray ........................... 16, 28
Document eject tray extension ................. 16
Document feeding .................................... 31
Automatic feeding ....................... 31, 32
Manual feeding ........................... 31, 34
Standard feeding ......................... 31, 32
Stand......................................................... 18
Startup screen ........................................... 21
Touch panel .................................. 16, 18, 19
Troubleshooting........................................ 44
Turning the power ON/OFF ..................... 21
T
U
Using the CD-4070NW ............................ 27
Web search function ................................. 14
W
Eject button .............................................. 18
External dimensions ................................. 48
E
Features .................................................... 12
Getting Started.......................................... 20
F
G
49
Download from Www.Somanuals.com. All Manuals Search And Download.
M
EM
O
50
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 8. Appendix
Patch code patterns
For details on how to use these patterns, see “Patch Code Sheets,” on p.35.
PATCH T (FILE A)
PATCH II (FILE B)
Download from Www.Somanuals.com. All Manuals Search And Download.
CANON ELECTRONICS INC.
1248, SHIMOKAGEMORI, CHICHIBU-SHI, SAITAMA 369-1892, JAPAN
CANON U.S.A. INC.
ONE CANON PLAZA, LAKE SUCCESS, N.Y. 11042, U.S.A.
CANON CANADA INC.
6390 DIXIE ROAD, MISSISSAUGA, ONTARIO L5T 1P7, CANADA
CANON EUROPA N.V.
BOVENKERKERWEG 59-61, P.O.BOX 2262, 1180 EG AMSTELVEEN, THE NETHERLANDS
CANON LATIN AMERICA, INC.
703 WATERFORD WAY, SUITE 400 MIAMI, FLORIDA 33126, U.S.A.
CANON AUSTRALIA PTY. LTD.
1 THOMAS HOLT DRIVE, NORTH RYDE, SYDNEY. N.S.W, 2113. AUSTRALIA
CANON SINGAPORE PTE. LTD.
1 HARBOUR FRONT AVENUE #04-01, KEPPEL BAY TOWER, SINGAPORE 098632
CANON HONGKONG COMPANY LTD.
19TH FLOOR, THE METROPOLIS TOWER, 10 METROPOLIS DRIVE, HUNGHOM, KOWLOON, HONG KONG.
*CE-IE-444*
PUB.CE-IE-444
0504AB0.3
CANON ELECTRONICS INC. 2004
PRINTED IN JAPAN
Download from Www.Somanuals.com. All Manuals Search And Download.
|