Canon Oven PIXMA MP560 User Manual

<< Previous  
Installing Your Multifunction  
to Your Network for the First Time  
PIXMA MP990 / PIXMA MP640 / PIXMA MP560  
Windows OS  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1
 
Preparing to Connect My Multifunction  
To My Network  
Network Requirements  
Before connecting the machine to the network, make sure that configuration of the computer and access point or router is  
complete, and that the computer is connected to the network.  
Notes on Network Connection  
The configuration, router functions, setup procedures and security settings of the network device vary depending on your  
system environment. For details, refer to your device's instruction manual or contact its manufacturer.  
The machine cannot be used over a wireless and wired connection at the same time.  
Wireless Connection  
Connect to your network environment over a wireless connection.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3
 
Preparing to Connect My Multifunction  
To My Network  
An "Ad-hoc connection," which establishes a direct  
connection to the computer over a wireless connection  
without using an access point, is not supported.  
Be sure to prepare an access point.  
Important Information You Need Before Adding Your Multifunction  
The following information is required to connect to your access point or router.  
Access Point Name/Network Name:  
Also referred to as SSID. A name to identify the specific access point.  
Network Key:  
Also referred to as encryption key, WEP key or WPA/WPA2 passphrase, Pre-Shared key.  
A password is required to prevent unauthorized access to communication.  
Check your access point or router for the following information, and then write it down.  
NOTE: For details on how to check the following information, refer to the manual of your access point or router, or contact its manufacturer.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4
 
Adding Your Multifunction to Your Network  
Adding Your Multifunction to Your Network  
Step One  
Step Two  
Use the Easy-Scroll Wheel* (A) to select Settings, and  
then press the OK button.  
Select Device settings, then press the OK button.  
*Easy-Scroll Wheel location varies according to model.  
MP640 pictured in examples below.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
5
 
Adding Your Multifunction to Your Network  
Step Three  
Step Four  
Select Yes, then press the OK button.  
Select Change wireless / wired, then press the OK button.  
When wireless connection is enabled, the Wi-Fi lamp**  
(B) lights blue.  
**Wi-Fi lamp location varies according to model.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
6
 
Adding Your Multifunction to Your Network  
Step Five  
Step SIx  
Select the access point name you wrote down,  
then press the OK button.  
When one of the following screens is displayed, enter the network  
key you wrote down, then press the OK button.  
If the following screen is not displayed, go to Step Eight.  
Use the Easy-Scroll Wheel to select the character. Use the  
to move the cursor to the right.  
button  
NOTE: If you are living in an apartment, nearby access  
points in use may be detected.  
IMPORTANT: Enter upper and lower case letters of the alphabet  
correctly.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
7
 
Adding Your Multifunction to Your Network  
Step Seven  
Step Eight  
Make sure that the network key is correct, and  
then press the OK button.  
When the completion screen appears, press the OK button, then  
press the HOME*** button (C).  
***HOME button location varies depending on model.  
The standby screen returns.  
NOTE: If Failed to connect to the access point. appears, press the OK  
button, make sure that the network key is correct, then enter it again. If a  
connection still cannot be established, refer to the printed manual: Network  
Setup Troubleshooting.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
8
 
Adding Your Multifunction to Your Network  
Confirm Connection Status  
Step One  
Step Two  
Press the HOME*** button (A), select Settings using the  
Easy-Scroll Wheel (B), and then press the OK button.  
Select Device settings, and then press the OK button.  
***HOME button location varies depending on model.  
IMPORTANT: Confirm connection status after installing  
the machine in the target location.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
9
 
Adding Your Multifunction to Your Network  
Step Three  
Step Four  
Select LAN settings, and then press the OK button.  
Select Confirm LAN settings, then press the OK button.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
10  
 
Adding Your Multifunction to Your Network  
Step Five  
Select Wireless LAN setting list, then press the OK button.  
Make sure that Connection is set to Active, and then press the HOME button.  
It may take a while before the connection is complete. In this case, press the Back* button (C) and wait for about a minute, then  
display the Wireless LAN setting list screen again.  
*Back button location varies depending on model.  
NOTE:  
If the communication status does not improve, make sure of the following.  
The machine and network device are turned on.  
There is no obstacle between the machine and access point, and wireless communication is possible.  
There is no microwave, refrigerator or any other object that may cause radio interference nearby.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
11  
 
Downloading and Installing the Drivers  
Downloading the Driver  
To use the machine by connecting it to a computer, software including the drivers needs to be copied (installed) to the computer's hard disk. The  
installation process takes about 20 minutes. (The installation time varies depending on the computer environment or the number of applications  
to be installed.)  
Step Two  
Step One  
Select your operating system in the Select OS dropdown  
menu.  
Go to the Drivers & Software for your model  
Download from Www.Somanuals.com. All Manuals Search And Download.  
12  
 
Downloading and Installing the Drivers  
Step Three  
In the Drivers section, click the Download icon  
for the MP Driver  
*Name varies by model  
example: MP990  
* The file name turns red when the mouse pointer is on the file name  
Download from Www.Somanuals.com. All Manuals Search And Download.  
13  
Downloading and Installing the Drivers  
Step Four  
On the next screen, read the information and instructions and click I Agree - Begin Download  
Select [Save] or [Run]. If [Run] is selected, the file will be automatically installed  
If [Save] is selected, once the file has been downloaded, double-click it to begin the installation process  
IMPORTANT:  
Quit all running applications before installation.  
Log on as the administrator (or a member of the Administrators group).  
Do not switch users during the installation process.  
Internet connection may be required during the installation. Connection fees apply.  
It may be necessary to restart your computer during the installation process. Follow the on-screen instructions. The  
installation resumes once your computer has restarted.  
If the firewall function of your security software is turned on, a warning message may appear that Canon software is attempting  
to access the network. If such a warning message appears, set the security software to always allow access.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
14  
 
Downloading and Installing the Drivers  
Installing the Driver  
NOTE: If a User Account Control screen appears, click Continue or Yes (depending on Windows version) to continue.  
NOTE: If the same screen reappears in subsequent steps, click Continue or Yes.  
Step One  
Step Two  
Click Next on the Welcome screen.  
Select your place of residence and click Next.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
15  
 
Downloading and Installing the Drivers  
Step Three  
Step Four  
Click Yes for the License Agreement.  
Installation proceeds  
Download from Www.Somanuals.com. All Manuals Search And Download.  
16  
 
Downloading and Installing the Drivers  
Step Four  
Step Five  
Select Use the Printer on network on the Connection  
method screen, and then click Next.  
After searching for printers, the Detected Printers List appears.  
Verify your printer is detected and click Next.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
17  
 
Downloading and Installing the Drivers  
Step Seven  
Step Six  
When the Connection Performance Measurement dialog box  
appears, click Next.  
Setup will install the driver components. After  
completion, click Next on the Setup Completion screen.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
18  
 
Downloading and Installing the Drivers  
Step Eight  
If the following window appears, click OK to restart or Cancel to  
restart later  
Confirm the measurement results, and then click Finish.  
Ensure that  
is displayed in Connection Performance between the Printer and the  
Access Point.  
If an icon other than  
appears, improve the communication status by referring to  
the displayed message or the help file, then click Remeasurement.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
19  
 

Bissell Vacuum Cleaner 81L8 User Manual
Blackberry Baby Gym 9780 User Manual
Black Box Cable Box A C 7P RO User Manual
Bloomfield Coffeemaker 8781A User Manual
Bosch Appliances Home Security System PLE 10M2 EU User Manual
Bose Home Theater System 1 SR User Manual
Breville Toaster BTA630XL User Manual
Broan Ventilation Hood RM503004 User Manual
Cecilware Cooktop IC 18A User Manual
Ceiva Digital Photo Frame SHR508A US User Manual