EF300mm f/2.8L IS II USM
EF400mm f/2.8L IS II USM
ENG
Instructions
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Precautions
Handling Cautions
Safety Precautions
OO If the lens is taken from a cold environment into a
warm one, condensation may develop on the lens
surface and internal parts. To prevent condensation
in this case, first put the lens into an airtight plastic bag
before taking it from a cold to warm environment. Then
take out the lens after it has warmed gradually. Do the
same when taking the lens from a warm environment
into a cold one.
OO Do not look at the sun or a bright light source
through the lens or camera. Doing so could result in
loss of vision. Looking at the sun directly through the
lens is especially hazardous.
OO Whether it is attached to the camera or not, do not
leave the lens under the sun without the lens cap
attached. This is to prevent the lens from concentrating
the sun’s rays, which could cause a fire.
OO Do not leave the lens in excessive heat such as in a car
in direct sunlight. High temperatures can cause the
lens to malfunction.
OO When the lens is mounted on a camera, be sure to also
hold the camera by the lens, including when mounting
on a tripod. Only holding by the camera could result in
scratches on the camera body or the lens itself. The lens
may also detach from its mount and fall, causing injury.
OO Do not use a strap attached to the camera. The mount
may break, resulting in the lens falling off and causing
injury or in scratches on the camera. Be sure to use the
camera with a dedicated strap attached correctly to the
strap mount on the lens.
Conventions used in this instruction
Warning to prevent lens or camera malfunction
or damage.
OO Do not stand on top of the lens case. You may fall and
injure yourself.
OO Do not pile lens cases on top of one another as they
may fall and cause injury.
Supplementary notes on using the lens and
taking pictures.
ENG-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Precautions
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) this
device must accept any interference received, including
interference that may cause undesired operation.
Do not make any changes or modifications to the equipment
unless otherwise specified in the instructions. If such changes
or modifications should be made, you could be required to
stop operation of the equipment.
This Class B digital apparatus complies with Canadian ICES-
003.
This equipment has been tested and found to comply with
the limits for a class B digital device, pursuant to part 15
of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
receiver.
• Consult the dealer or an experienced radio/TV technician
for help.
ENG-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Nomenclature
Focusing ring (→ 6)
Distance scale (→ 14)
Hood mount (→ 14)
Orientation locking knob (→ 17)
Security slot (covered) (→ 17)
Strap mount (→ 5)
Drop-in filter (→ 18)
Rubber ring (→ 5)
Playback ring
(→ 9)
AF stop button
(→ 7)
Contacts (→ 5)
Image stabilizer mode selector switch (→ 11)
Image stabilizer switch (→ 11)
Focus preset button (→ 8)
Lens mount index (→ 5)
Focusing distance range
selector switch (→ 6)
Focus preset switch (→ 8)
Tripod mount (→ 17)
Focus mode switch (→ 6)
OO The illustrations used in the explanations in this manual show, with a few exceptions, the EF300mm
f/2.8L IS II USM, but the EF400mm f/2.8L IS II USM is used in the same way.
OO For detailed information, reference page numbers are provided in parentheses (→ **).
ENG-4
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Mounting and Detaching the Lens
See your camera’s instructions for details on
mounting and detaching the lens.
The lens mount has a rubber ring for enhanced
dust- and water-resistance. The rubber ring may
cause slight abrasions around the camera’s lens
mount, but this will not cause any problems. If the
rubber ring becomes worn, it is replaceable by a
Canon Service Center at cost.
Attaching the strap
OOAfter detaching the lens, place the lens with
the rear end up to prevent the lens surface and
contacts from getting scratched.
OOIf the contacts get soiled, scratched, or have
fingerprints on them, corrosion or faulty
connections can result. The camera and lens
may not operate properly.
OOIf the contacts get soiled or have fingerprints on
them, clean them with a soft cloth.
OOIf you remove the lens, cover it with the dust cap.
To attach it properly, align the lens mount index
and the index of the dust cap as shown in
the diagram, and turn clockwise. To remove it,
reverse the order.
Thread the end of the strap through the strap
mount on the lens and then back through the
clasp on the strap. Pull the strap tight and check
that there is no slack in the clasp.
ENG-5
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Setting the Focus Mode 3. Switching the Focusing
Distance Range
To shoot in autofocus (AF) mode, set the focus
mode switch to AF.
You can set the focusing distance range with a
To shoot in manual focus (MF) mode, set the
switch. By setting a suitable focusing distance
focus mode switch to MF, and focus by turning
range, the actual autofocusing time will be
the focusing ring. The focusing ring always
shorter.
works, regardless of the focus mode.
To shoot in power focus (PF) mode, set the
focus mode switch to PF when the focus preset
switch (p. 8) is at OFF.
Operating the playback ring enables focus
change at a set speed. This is a useful feature
for changing focus when shooting movies.
Lens
Ranges
FULL
2 m/6.6 ft. – 6 m/19.7 ft.
6 m/19.7 ft. – ∞
FULL
EF300mm f/2.8L IS II USM
2.7 m/8.9 ft. – 7 m/23 ft.
7 m/23 ft. – ∞
EF400mm f/2.8L IS II USM
After autofocusing in ONE SHOT AF mode, focus
manually by pressing the shutter button halfway
and turning the focusing ring. (Full-time manual
focus)
ENG-6
Download from Www.Somanuals.com. All Manuals Search And Download.
4. AF Stop Button
The AF stop function also works in AI Servo AF
mode.
Angle positioning of the AF stop button is
adjustable by a Canon Service Center at cost.
OOWith the EOS 630/600, RT, A2/A2E/5, or 10S/10
set to the AI Servo AF mode and continuous
shooting, AF will not resume even after you
let go of the AF stop button. Press the shutter
release button halfway to resume AF.
During autofocus operation, you can press the
AF stop button to temporarily pause autofocus.
OOWith the EOS A2/A2E/5 and 10S/10 set to the
Sports mode, AF will not resume even after you
let go of the AF stop button. Press the shutter
release button halfway to resume AF.
If the shutter button is still pressed halfway when
the AF stop button is released, autofocusing will
continue as before.
OOYou can change the functions of the AF stop
button using the camera’s Custom Function. For
details, please refer to the camera’s instructions.
ENG-7
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Focus Preset
By presetting any focusing distance, you can instantly focus at that point even while you are
shooting a different subject. This function operates in any of the AF, PF, and MF modes.
< How to Set >
Set the focus preset switch
to ON or
Press the shutter button
halfway to focus the
Press the focus preset
button.
.
distance you want to preset.
OOThe focused distance will be
preset.
OOIf the focus preset switch was
set to
, the beeper will
sound once.
ENG-8
Download from Www.Somanuals.com. All Manuals Search And Download.
Focus Preset
< How to Focus at the Preset Distance >
OOWhen turning the playback ring, keep your finger
away from the shutter button. In One-Shot AF
mode, the exposure will be locked when you
press the shutter button halfway and focus is
achieved. So if you press the shutter button
halfway while turning the playback ring, the
exposure may not be correct.
OOWhen not using the focus preset, set the switch
to OFF.
OOThe focus preset function will not work while a
Live View image is displayed on the camera.
By turning the playback ring to the left or right,
the focus shifts as far as the preset distance.
Focus will shift freely released of AF focusing
while the playback ring is still turned.
In the following cases, the focusing distance scale
(p. 14) will move slightly. It will not affect the image.
• When you press the focus preset button.
• When you turn the playback ring.
OOIf the focus preset switch was set to
, the beeper
will sound twice.
ENG-9
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Power Focus (PF) Mode
Using the playback ring enables smooth focus change.
This is a useful feature for changing focus when shooting movies.
With the focus preset switch set to OFF, set the focus mode
switch to PF.
Rotate the playback ring to
change the focus.
When the playback ring is rotated in a certain direction, focus changes in the same direction as when
the focusing ring is rotated.
You can make a 2-step change in focus shift speed depending on the angle that the playback ring is
rotated to.
ENG-10
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Image Stabilizer
You can use the image stabilizer in AF, PF, or MF mode.
Set the STABILIZER switch
to ON.
Select the stabilizer mode.
First press the shutter
button down halfway, then
press down all the way to
take the picture.
OO MODE 1: Corrects vibrations in
all directions. It is mainly effective
for shooting still subjects.
OOMODE 2: Corrects vertical
camera shake during
following shots in a horizontal
direction, and corrects
horizontal camera shake
during following shots in a
vertical direction.
OO MODE 3: Corrects vibration only
during exposure. During panning
shots, corrects vibration during
exposure only in one direction
the same as MODE 2.
OOIf you are not going to use the
image stabilizer function, set
the switch to OFF.
OOMODE 1, 2: Press the
shutter button down halfway
to stabilize the image in
the viewfinder and enable
stabilization.
OOMODE 3: Press the shutter
down halfway to initiate
computation of stabilization,
then press down all the way
to enable stabilization.
ENG-11
Download from Www.Somanuals.com. All Manuals Search And Download.
8. Tips on Using the Image Stabilizer
The image stabilizer for this lens is effective for hand-held shots in the following conditions.
O MODE 1
O MODE 2
ON
ON
OFF
OFF
OOIn semi-darkened areas such as indoors or
outdoors at night.
OOWhen panning subjects in motion.
OOIn locations where flash photography is
prohibited, such as art museums and theater
stages.
OOIn situations where your footing is uncertain.
OOIn situations where fast shutter settings
cannot be used.
O MODE 3
OOSince camera shake is stabilized only during
exposure, following a subject is easier such as
when shooting a fast and irregularly moving
player during sports photography.
ENG-12
Download from Www.Somanuals.com. All Manuals Search And Download.
Tips on Using the Image Stabilizer
OOThe Image Stabilizer cannot compensate for a
blurred shot caused by a subject that moved.
OOSet the STABILIZER switch to OFF when you
are taking pictures using the Bulb setting (long
exposures). If the STABILIZER switch is set to
ON, the image stabilizer function may introduce
errors.
OOUsing a tripod also stabilizes the image.
However, depending on the kind of tripod and
shooting conditions, sometimes it may be better
to turn off the Image Stabilizer function.
OOThe stabilizer is equally effective for hand-
held photography and photography with a
monopod. The Image Stabilizer effect may be
reduced, however, depending on the shooting
environment.
OOThe Image Stabilizer might not be fully effective
in the following cases:
• You shoot from a violently moving vehicle.
• You move the camera dramatically for a
panning shot in Mode 1.
OOThe Image Stabilizer consumes more power than
normal shooting, so fewer shots can be taken if
you use the function.
OOThe image stabilizer operates for about two
seconds even when your finger is off the
shutter button. Do not remove the lens while
the stabilizer is in operation. This will cause a
malfunction.
OOThe Image Stabilizer also operates when the
lens is used with extension tube EF12 II or EF25
II or the extender EF1.4× III or EF2× III.
OODepending on the camera there may be image
shake, such as after releasing the shutter.
However, this does not affect shooting.
OOIf you set the camera’s Custom Function to
change the assigned button to operate the AF,
the Image Stabilizer will operate when you press
the newly assigned AF button.
OOWith the EOS-1V/HS, 3, ELAN 7E/ELAN
7/30/33, ELAN 7NE/ELAN 7N/30V/33V, ELAN II/
ELAN II E/50/50E, REBEL 2000/300, IX, IX Lite/
IX7, and D30, the Image Stabilizer will not work
during self-timer operation.
ENG-13
Download from Www.Somanuals.com. All Manuals Search And Download.
9. Infinity Compensation
Mark
10. Hood
Infinity compensation mark
Distance index
The special hoods that come with all these
lenses cut out unwanted light and protect the
front of the lens from rain, snow, and dust.
To compensate for shifting of the infinity focus
point that results from changes in temperature.
The infinity position at normal temperature is the
point at which the vertical line of the distance
scale L mark is aligned with the distance index.
To attach the hood, loosen the hood lock knob
by turning it counterclockwise. Fit the hood onto
the lens’s hood mount, and tighten the lock knob
to fix it in place. Use the same procedure, in
reverse, to remove the hood.
For accurate focusing in MF on subjects at infinity
distance, look through the viewfinder while rotating
the focusing ring.
ENG-14
Download from Www.Somanuals.com. All Manuals Search And Download.
11. Fitting the Lens Cap
Reverse the lens hood, slip
it over the lens, and tighten
the lock knob to fix it in
place.
Lift the hook and loop
With the lock knob at the
opening in the cap, close
the fastener to fix the cap in
place as shown.
fastener, and fit the cap so
that the lock knob rides up
the slot in the cap.
OOCan also be attached to the
front of the hood when using
the lens.
ENG-15
Download from Www.Somanuals.com. All Manuals Search And Download.
12. Case
Slot
Lid
Hinge
Strap
Lever
Keyhole
The illustration shows the EF400mm f/2.8L IS II USM.
Fold the strap and fit it into the space near
Put the lens away as follows.
the case hinges.
Reverse the lens hood, slip it over the lens,
and attach the lens cap.
Fasten the lens securely with the strap.
Close the lid, and then push the lever while
holding the lid from above to lock.
Position the tripod mount towards you as
shown and place it in the case.
Place so that the hood’s lock knob rests in
the slot near you.
OODo not sit on top of the lens case.
OOPlace the lens in the position intended for it.
ENG-16
Download from Www.Somanuals.com. All Manuals Search And Download.
13. Using the Tripod
Mount
14. Security Slot
A tripod or monopod attaches to the tripod
mount on the lens.
Adjusting the Tripod Mount
By loosening the orientation locking knob on the
tripod mount you can rotate the camera to set
the image for any vertical or horizontal position.
An attachment slot is provided for a wire-type
security lock. The slot is located under the cover
for the orientation locking knob.
Replacing the Tripod Mount (EF400mm
f/2.8L IS II USM only)
Replacement with the included monopod mount
can be done at a Canon Service Center at cost.
Since the mount requires special fastening, as
a safety precaution, do not replace the mount
yourself.
A wire-type security lock can be purchased
separately.
ENG-17
Download from Www.Somanuals.com. All Manuals Search And Download.
15. Drop-In Filters
<Using a Gelatin Filter>
A 52(WII)-series drop-in gelatin filter holder with
a glass filter is included with the lens. The drop-
in filter holder can be used fitted with a gelatin
filter (sold separately).
14mm
14mm
47mm
47mm
<Installing and Removing>
Lift up the holder’s retaining plate.
To remove the drop-in filter, press in the left
and right lock buttons and pull the filter holder
straight up out of the slot.
Cut the gelatin filter as shown and mount it in
the holder.
Return the retaining plate to its closed
position.
To install the drop-in filter, push the filter holder
straight down into the slot until it clicks into place.
The Drop-In Screw-Type Filter Holder 52(WII) and
Drop-In Circular Polarizing Filter PL-C52(WII) are
also available (sold separately).
OOThe filter holder can be installed facing either
forwards or backwards.
Because the lens optics are designed to include a
glass filter, you must always install the filter holder,
even if no gelatin filter is fitted.
ENG-18
Download from Www.Somanuals.com. All Manuals Search And Download.
16. Extenders (Sold Separately)
Lens specifications when using extender EF1.4× II/III or EF2× II/III are as follows.
EF300mm f/2.8L IS II USM
EF400mm f/2.8L IS II USM
EF1.4× II/III
420
f/4 – 45
5° 55’
3° 15’
4° 55’
EF2× II/III
600
f/5.6 – 64
4° 10’
2° 20’
3° 30’
EF1.4× II/III
560
f/4 – 45
4° 25’
2° 25’
3° 40’
EF2× II/III
800
f/5.6 – 64
3° 5’
1° 40’
2° 35’
0.35
Focal length (mm)
Aperture
Diagonal
Vertical
Horizontal
Angle of view
Maximum magnification (×)
0.25
0.36
0.25
OOAttach the extender to the lens, and then attach the lens to the camera. To remove it, reverse the order.
Errors may occur if you attach the extender to the camera first.
OOWhen shooting with EOS A2/A2E/5 fitted with either the EF300mm f/2.8L IS II USM or EF400mm f/2.8L IS
II USM, use –0.5 step exposure compensation when using extender EF1.4× II, and use –1 step exposure
when using extender EF2× II.
OOExtenders cannot be used more than one at a time.
OOAF is possible with extender EF1.4× II/III or EF2× II/III.
OOWhen an extender is attached, the AF speed will become slower to retain proper control.
ENG-19
Download from Www.Somanuals.com. All Manuals Search And Download.
17. Extension Tubes
(Sold Separately)
You can attach extension tube EF12 II or EF25
II for magnified shots. The shooting distance and
magnification are shown below.
EF300mm f/2.8L IS II USM
Focusing Distance Range (mm)
Magnification (×)
Close distance Long distance Close distance Long distance
EF12 II
EF25 II
1700
1480
7529
3727
0.22
0.28
0.04
0.09
EF400mm f/2.8L IS II USM
Focusing Distance Range (mm)
Magnification (×)
Close distance Long distance Close distance Long distance
EF12 II
EF25 II
2375
2113
13353
6494
0.21
0.26
0.03
0.07
MF mode is recommended for accurate focusing.
ENG-20
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
EF300mm f/2.8L IS II USM
300mm f/2.8
12 groups, 16 elements
f/32
EF400mm f/2.8L IS II USM
400mm f/2.8
12 groups, 16 elements
f/32
Focal Length/Aperture
Lens Construction
Minimum Aperture
Diagonal: 8° 15’
Vertical: 4° 35’
Horizontal: 6° 50’
Diagonal: 6° 10’
Vertical: 3° 30’
Horizontal: 5° 10’
Angle of View
Min. Focusing Distance
Max. Magnification
2 m/6.6 ft.
0.18×
2.7 m/8.9 ft.
0.17×
Approx. 136 × 205 mm/
5.4 × 8.1 inch (at 2 m/6.6 ft.)
Approx. 139 × 208 mm/
5.5 × 8.2 inch (at 2.7 m/8.9 ft.)
Field of View
Filter
Any 52(WII)-series drop-in filter
Max. Diameter and Length
Weight
Hood
128 × 248 mm/5.0 × 9.8 inch
Approx. 2350 g/82.9 oz
ET-120(WII)
163 × 343 mm/6.4 × 13.5 inch
Approx. 3850 g/135.8 oz
ET-155(WII)
Lens Cap
Case
E-145C
Lens case 300B
E-180D
Lens case 400C
OO The lens length is measured from the mount surface to the front end of the lens. Add 26.5 mm
when including the lens cap and dust cap.
OO The size and weight listed are for the lens only, except as indicated.
OO The Close-up Lenses 250D and 500D cannot be attached.
OO Aperture settings are specified on the camera.
OO All data listed is measured according to Canon standards.
OO Product specifications and appearance are subject to change without notice.
ENG-21
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
0311SZ © CANON INC. 2011
CT1-8570-002
|