EF14mm f/2.8L II USM
ENG
Download from Www.Somanuals.com. All Manuals Search And Download.
Instruction
a Safety Precautions
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause
undesired operation.
Do not make any changes or modifications to the equipment
unless otherwise specified in the instructions. If such changes or
modifications should be made, you could be required to stop
operation of the equipment.
This equipment has been tested and found to comply with the
limits for a class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
againharmful interference in a residential installation. This
ipment generates, uses and can radiate radio frequency
eergy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not occur in
a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of
the following measures:
a Safety Precautions
• Do not look at the sun or a bright light source
through the lens or camera. Doing so could result
in loss of vision. Looking at the sun directly through
the lens is especially hazardous.
• Whether it is attached to the camera or not, do
not leave the lens under the sun without the
lens cap attached. This is to prevent the lens from
concentrating the sun’s rays, which could cause a
fire.
Handling Cautions
• If the lens is taken from a cold environment into
a warm one, condensation may develop on the
lens surface and internal parts. To prevent
condensation in this case, first put the lens into an
airtight plastic bag before taking it from a cold to
warm environment. Then take out the lens after it
has warmed gradually. Do the same when taking
the lens from a warm environment into a cold one.
• Do not leave the lens in excessive heat such as in
a car in direct sunlight. High temperatures can
cause the lens to malfunction.
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Consult the dealer or an experienced radio/TV technician for
help.
This Class B digital apparatus complies with Canadian ICES-003.
ENG-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Nomenclature
Distance scale (→ 5, 6)
Infrared index (→ 6)
Built-in lens hood
Depth-of-Field scale (→ 6)
Distance index (→ 5)
Gelatin filter holder (→ 7)
Contacts (→ 4)
Focusing ring (→ 5)
Focus mode switch (→ 5)
Lens mount index (→ 4)
For detailed information, reference page numbers are provided in parentheses (→ **).
ENG-3
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Mounting and Detaching the Lens
See your camera’s instructions for details on
mounting and detaching the lens.
See the diagrams below for directions for
removing and attaching the lens cap.
¡After detaching the lens, place the lens with the
rear end up to prevent the lens surface and
electrical contacts from getting scratched.
¡If the contacts get soiled, scratched, or have
fingerprints on them, corrosion or faulty
connections can result. The camera and lens
may not operate properly.
The lens mount has a rubber ring for enhanced
water- and dust-resistance. The rubber ring may
cause slight abrasions around the camera's lens
mount, but this will not cause any problems. If the
rubber ring becomes worn, it is replaceable by a
Canon Service Center at cost.
¡If the contacts get soiled or have fingerprints on
them, clean them with a soft cloth.
¡If you remove the lens, cover it with the dust
cap. To attach it properly, align the lens mount
index and the
K
index of the dust cap as shown
in the diagram, and turn clockwise. To remove it,
reverse the order.
ENG-4
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Setting the Focus Mode
3. Infinity Compensation Mark
Infinity compensation mark
Distance index
To shoot in autofocus mode, set the focus mode
switch to AF.
To compensate for shifting of the infinity focus
point that results from changes in temperature.
To use only manual focusing, set the focus mode he infinity position at normal temperature is the
switch to MF, and focus by turning the focusing
ring. The focusing ring always works, regardless
of the focus mode.
point at which the vertical line of the L mark is
aligned with the distance indicator on the
distance scale.
After autofocusing in ONE SHOT AF mode, focus
manually by pressing the shutter button halfway
and turning the focusing ring. (Full-time manual
focus)
For accurate manual focusing on subjects at
infinity distance, look through the viewfinder while
rotating the focusing ring.
ENG-5
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Infrared Index
5. Depth-of-Field Scale
The infrared index corrects the focus setting
when using monochrome infrared film. Focus on
the subject manually, then adjust the distance
setting by moving the focusing ring to the
corresponding infrared index mark.
The depth of field is the distance in front of and
behid the plane of focus on the subject that
pears sharp. The depth of field is indicated by
te area between the depth-of-field scale lines
below the distance scale. The numbers on the
scale are F values, and for example, if the
shooting distance is 0.5m and the aperture is
f/16, the area in focus will extend from about
0.3m to infinity.
Some EOS cameras cannot use infrared film. See
the instructions for your EOS camera.
¡The infrared index position is based on a
wavelength of 800 nm.
¡Be sure to observe the manufacturer’s
instructions when using infrared film.
¡Use a red filter also when you take the picture.
The depth-of-field scale is an approximate
indicator.
ENG-6
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Filter Holder
There is a gelatin filter holder at the rear of the
lens. Cut the gelatin filter to fit within the white
frames. Then insert the gelatin filter into the filter
holder.
¡Only one filter can be used.
¡When you use a gelatin filter, ghosting may
appear in the image.
ENG-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
Image Size
24 × 36 mm
14 mm f/2.8
11 groups, 14 elements
f/22
Focal Length/Aperture
Lens Construction
Minimum Aperture
Angle of View
Min. Focusing Distance
Max. Magnification
Field of View
Diagonal: 114°
0.2 m / 0.7 ft.
0.15 ×
Vertical: 81°
Horizontal: 104°
162 × 250 mm / 6.4 × 9.8 inch (at 0.2 m)
Filter
Insert
Hood
Built-in
Case
LP1016
Max. Diameter and Length
Weight
80 × 94 mm / 3.1 7 inch
645 g / 22.7 oz
¡The lens length is measured from the mount surface to the front end of the lens. Add 21.5 mm when including
the lens cap and dust cap.
¡The size and weight listed are for the lens only, except as indicated.
¡The EF1.4X II/EF2X II extender, the EF12 II/EF25 II extension tube, and 250D/500D close-up lenses cannot be
used with this lens.
¡Aperture settings are specified on the camera.
¡All data listed is measured according to Canon standards.
¡Product specifications and appearance are subject to change without notice.
ENG-8
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
© CANON INC. 2007
CT1-7573-002
2009.7
|