September 24, 2009
Revision 0
C5051/C5045/C5035/C5030 Series
imageRUNNER ADVANCE
Service Manual
Product Outline
Function
Periodic Servicing
Parts Replacing and Cleaning
Adjustments
Troubleshooting
Error Code
Service Mode
Installation
Appendix
Download from Www.Somanuals.com. All Manuals Search And Download.
1 2 3 4 5 6 7 8 9
fineline6
0-3
The following rules apply throughout this Service Manual:
Explanation of Symbols
The following symbols are used throughout this Service Manual.
1. Each chapter contains sections explaining the purpose of specific functions and the
relationship between electrical and mechanical systems with reference to the timing of
Symbols
Explanation
Symbols
Explanation
operation.
In the diagrams,
represents the path of mechanical drive; where a signal name
Check.
Remove the claw.
accompanies the symbol, the arrow
indicates the direction of the electric
signal.
F-0-1
F-0-2
The expression "turn on the power" means flipping on the power switch, closing the
front door, and closing the delivery unit door, which results in supplying the machine with
power.
Check visually.
Insert the claw.
F-0-3
F-0-5
F-0-4
F-0-6
Check the noise.
Use the bundled part.
Push the part.
2. In the digital circuits, '1' is used to indicate that the voltage level of a given signal is
"High", while '0' is used to indicate "Low". (The voltage value, however, differs from
circuit to circuit.) In addition, the asterisk (*) as in "DRMD*" indicates that the DRMD
signal goes on when '0'.
Disconnect the connector.
Connect the connector.
In practically all cases, the internal mechanisms of a microprocessor cannot be checked
in the field. Therefore, the operations of the microprocessors used in the machines
are not discussed: they are explained in terms of from sensors to the input of the DC
controller PCB and from the output of the DC controller PCB to the loads.
F-0-7
F-0-8
Plug the power cable.
Turn on the power.
F-0-9
F-0-10
F-0-12
Remove the cable/wire
from the cable guide or wire
saddle.
The descriptions in this Service Manual are subject to change without notice for product
improvement or other purposes, and major changes will be communicated in the form of
Service Information bulletins.
F-0-11
F-0-13
F-0-14
F-0-15
All service persons are expected to have a good understanding of the contents of this Service
Manual and all relevant Service Information bulletins and be able to identify and isolate faults
in the machine.
Set the cable/wire to the
cable guide or wire saddle.
Remove the screw.
Tighten the screw.
0-3
Download from Www.Somanuals.com. All Manuals Search And Download.
fineline6
CDRH Act
Laser Safety
Handling of Laser System
Turn power switch ON
Safety of Toner
■
■
■
■
■
■
imageRUNNER ADVANCE
C5051/5045/5035/5030
Series
Notes When Handling a
Lithium Battery
Notes Before Servicing
■
Download from Www.Somanuals.com. All Manuals Search And Download.
fineline6
0
0-2
CDRH Act
Handling of Laser System
The Center for Devices and Radiological Health of the US Food and Drum Administration put
into force regulations concerning laser products on August 2, 1976. These regulations apply
to laser products manufactured on and after August 1, 1976, and the sale of laser products
not certified under the regulations is banned within the Untied States. The label shown here
indicates compliance with the CDRH regulations, and its attachment is required on all laser
products that are soled in the United States.
When servicing the area around the laser assembly, be sure to turn off the main power.
The machine's covers that can reflect laser light are identified by means of a warning label
(Figure). If you must detach a cover showing the label, be sure to take extra caution during
the work.
CANON INC.
30-2,SHIMOMARUKO,3-CHOME,OHTA-KU,TOKYO,JAPAN
MANUFACTURED:
THIS PRODUCT CONHORMS WITH DHHS RADIATION
PERFORMANCE STANDARD 21CFR CHAPTER 1
SUBCHAPTER J.
F-0-16
A different description may be used for a different product.
F-0-17
Laser Safety
Laser beam radiation may pose a danger to the human body. A laser scanner mounted on the
machine is sealed with the protection housing and external cover to prevent the laser beam
from leaking to the outside. The laser beam never leaks out of the scanner as far as users
operate the machine normally.
0-2
Download from Www.Somanuals.com. All Manuals Search And Download.
0
fineline6
0
0-3
Turn power switch ON
Safety of Toner
The machine is equipped with 2 power switches: main power switch and control panel power
About Toner
switch.
The machine goes on when the main power switch is turned on (i.e., other than in low power
mode, sleep mode).
The machine's toner is a non-toxic material made of plastic, iron, and small amounts of dye.
Do not throw toner into fire. It may cause explosion.
If your clothing or skin has come into contact with toner, wipe it off with tissue; then, wash it
off with water.
•
•
•
Do not use warm water, which will cause the toner to jell and fuse permanently with the
fibers of the cloth.
Tonner is easy to react with plastic material, avoid contact with plastic.
0-3
Download from Www.Somanuals.com. All Manuals Search And Download.
0
fineline6
0
0-4
Notes When Handling a Lithium Battery
RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE.
DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS.
The following warnings are given to comply with Safety Principles (EN60950).
Wenn mit dem falschen Typ ausgewechselt, besteht Explosionsgefahr.
Gebrauchte Batterien gemäß der Anleitung beseitigen.
Notes Before Servicing
At servicing, be sure to turn OFF the power source according to the specified steps and
disconnect the power plug.
0-4
Download from Www.Somanuals.com. All Manuals Search And Download.
0
fineline6
|