Washing machine
Instructions for use
CWB 110
Download from Www.Somanuals.com. All Manuals Search And Download.
M) N.B!
If the appliance is installed on a carpeted floor ensure that the ventilation holes on the
base of the appliance are not obstructed.
N) If the appliance is not running properly or breaks down, switch it off, turn off the tap and do
not tamper with the appliance.
Consult only the Authorised Technical Support Service for possible repair and ask them to
use original spare parts.
Failure to comply with the above can compromise the safety of the appliance.
O) If the appliance’s power cable should ever need replacing, consult the Authorised
Technical Support Service
General delivery notes
Please check that the following items are delivered with the appliance:
- Instruction manual
- Certificate of guarantee
- Inlet hose
- Liquid detergent or liquid bleach compartment
Check that no damage has occurred during transit, and if so, call your nearest Authorised
Technical Support Service agent.
Quick start
Washing
-
-
-
-
Open the door by using the button “A” (Fig. 1, page 6)
Select laundry and put it in the machine
Close the door
Put detergent in the compartments as indicated in the programme guide in this instruction
manual
Safety notes
Note:
-
-
Select programme
Wait for the “STOP” indicator light to flash
for cleaning or maintenance of the washing machine.
A) Pull out the plug
B) Turn off the tap
Press additional function buttons (if required)
C) Candy equips all its appliances with earthing. Ensure that the mains supply is earthed,
and if it is not, seek assistance from a qualified person.
D) Do not touch the appliance when hands or feet are wet or damp. Do not use the appliance
with bare feet.
-
-
Press the “Start/Pause” button (page 7)
After few seconds the appliance starts working.
E) The use of adapters, multiple connectors and/or extensions is not recommended.
After washing
-
-
The indicator light “STOP” will go on.
Wait for the door lock to be released
Note:
(about 2 minutes after the programme has finished).
The “Door Security” indicator light will go out.
Switch off the washing machine by turning the selector
to “OFF” position.
water temperature can reach 90°C during the wash cycle.
-
-
F) Check there is no water left in the drum before opening the door.
Open the door and remove the laundry.
G) Do not allow children or unauthorised persons to use the appliance without supervision.
H) Do not pull the power cable or the appliance itself to remove the plug from the socket.
I) The appliance must not be exposed to weather conditions (rain, direct sun, etc...)
L) When moving the appliance never lift it by the controls or by the detergent drawer.
When in transit never rest the door against the trolley or transport the appliance without
the polystyrene base.
Ensure that the machine is correctly installed in line with the instructions found on page 26.
4
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Door open button
Description of controls
A
Important:
Fig. 1
a special safety device prevents the door from opening at the end of the wash/spin cycle. at
the end of the spin phase wait up to 2 minutes before opening the door.
L
DOOR SECURITY indicator light
B
The “Door Security” indicator light is illuminated when the door is fully closed and the machine is ON.
When "Start/Pause" is pressed on the machine with the door closed the indicator will flash
momentarily and then illuminate.
M
If the door is not closed the indicator will continue to flash.
Aspecial safety device prevents the door from being opened immediately after the end of the cycle.
Wait for 2 minutes after the wash cycle has finished and the “Door Security” light has gone out
before opening the door. At the end of the cycle turn the programme selector to "OFF" .
B
A
P
C
F
E G
N
D
H
I
START/PAUSE button
C
When a programme is selecting, wait for the “STOP” indicator
light to flash before pressing the "Start/Pause" button.
Door open button
Door locked indicator light
Start button
A
B
C
D
E
F
G
H
I
Press to start the selected cycle (according to the selected cycle one indicator lights will go on) .
Start Delay button
Super rapid button
Extra Rinse button
Crease guard button
Spin speed control
NOTE: When the "Start/Pause" button has been pressed,
the appliance can take few seconds before it starts
working.
Changing the settings after the programmes has started (PAUSE)
The programme may be paused at any time during the wash cycle by holding down the
"Start/Pause" button for about two seconds. When the machine is in the paused mode, the
indicator light "Time to end" and option buttons will flash.
To restart the programme, press the "Start/Pause" button once again.
If you wish to add or remove items during washing, wait 2 minutes until the safety device
unlocks the door.
Wash Temperature Control Knob
“Time to end” indicator light
Buttons indicator light
L
M
N
P
Timer knob for wash programmes with OFF position
Detergent drawer
When you have carried out the manoeuvre, close the door, press "Start/Pause" button and
the appliance will continue working where it left off.
CANCELLING THE PROGRAMME
To cancel the programme the programme selector should be rotated to the "OFF" position.
6
7
Download from Www.Somanuals.com. All Manuals Search And Download.
The option buttons should be selected before pressing
the "Start/Pause" button.
CREASE GUARD button
Press the button to select or deselect this function.
The Crease Guard function minimizes creases as much as possible with a uniquely designed
anti-crease system that is tailored to specific fabrics.
G
START DELAY BUTTON
D
MIXED FABRICS - the water is gradually cooled throughout the final two rinses with no
spinning and then a delicate spin assures the maximum relaxation of the fabrics.
Appliance start time can be set with this button, delaying the star by 3, 6 or 9 hours.
Proceed as follow to set a delayed start:
Select a programme (“STOP” indicator light blinks)
DELICATE FABRICS – final two rinses with no spinning and then the fabrics are left in water
until it is time to unload. When you are ready to unload, press the "Crease Guard" button –
this will drain.
Press Start Delay button (each time the button is pressed the start will be delayed by 3, 6 or
9 hours respectively and the corresponding light will blink).
Press START to commence the Start Delay operation (the indicator light associated with the
selected Start Delay time stops blinking and remains ON).
WOOLLENS/HAND WASH – after the final rinse the fabrics are left in water until it is time to
unload and the button indicator blinking.
At the end of the required time delay the programme will start.
To cancel the Start Delay function :
When you are ready to unload, press the "Crease Guard" button, this will drain and spin
ready for emptying.
press the Start Delay button until the indicator lights will be off (The STOP light blinks) and
the programme can be started manually using the START button or switch off the appliance
by turning the programme selector to off position.
If you do not want to spin the clothes and activate drain only:
- Turn the programme selector to the "OFF" position;
- Select programme drain only
;
- Switch on the appliance again by pressing the "Start/Pause" button.
SUPER RAPID button
E
Pressing this button reduces the time of the wash programme by a maximum of 50 minutes
depending on the programme and the temperature selected. The "Super Rapid" button can
be used for washing loads of 1 to 5,5 kg. This option may only be utilised on COTTONS and
SYNTHETICS programmes.
F
EXTRA RINSE BUTTON
Thanks to the new electronic system, acting on the button is possible to effect a new special
rinse cycle. The addition of a lot of more water and the new action combined of cycles of
rotation of the drum with load and unloading of water, allow to get laundry perfectly rinsed.
This function has been studied for the people with delicate and sensitive skin, for which also a
least residue of detergent can cause irritations or allergies.
It advises to also use this function for the children items and in case of washings of very dirty
items, for which it is due to use a lot of detergent, or in the washing of towelling items whose
fibers mostly have the tendency to hold the detergent.
This button is not available in the Wool/Hand wash programmes.
9
8
Download from Www.Somanuals.com. All Manuals Search And Download.
VARIABLE SPIN SPEED selector
Can be turned in either direction
TIME TO END indicator light
In order to manage your time better, this washing machine features an indicator light system
that keeps you constantly informed on the remaining cycle time.
L
H
Indicator light START:
Remaining time above 60 minutes.
Indicator light 60:
Remaining time less than 60 minutes.
Indicator light 30:
Remaining time less than 30 minutes.
Indicator light 15:
Remaining time less than 15 minutes.
Indicator light STOP:
The spin stage plays a very important role in preparing the
laundry for efficient drying and your model offers maximum
flexibility to suit all your requirements.
The selector can be turned to reduce the maximum spin
speed, right up to eliminating the spin completely (position
In programmes for mixed fibres, synthetics and delicates,
the washing machine automatically lowers the spin speed.
).
In order not to damage fabrics, it is not possible to increase this spin speeds.
End of the programme.
Note: this model is fitted with an electronic device that
Buttons indicator light
The indicator light around the option buttons will light when specific options are selected.
M
checks the load is balanced correctly. If the load is slightly
unbalanced the machine will re-balance it automatically to carry
out the normal spin.
If, after several attempts, balance is not restored, a reduced spin
speed will be used.
If loads are seriously unbalanced the spin stage will be cancelled.
This helps limit vibration, reduce noise output and improve the
washing machine’s lifespan.
PROGRAMME selector with "OFF" position
N
Rotates in both directions.
The machine is turned on by selecting a
programme via the programme selector.
This status will be indicated by the
"STOP" indicator light flashing, this light
will continue to flash until the machine
has started or the machine is returned to
the "OFF" position.
WASH TEMPERATURE CONTROL KNOB
I
ROTATES IN BOTH DIRECTIONS
With this device it is possible to reduce, but no increase
washing cycle temperature.
Press the "Start/Pause" button to start the selected cycle.
The table of programmes indicate the maximum temperature
advised for each type of wash.
Once a programme is selected the programme selector remains stationary on the selected
programme till cycle ends.
Switch off the washing machine by turning the selector to "OFF".
Note:
The programme selector must be returned to the "OFF" position
at the end of each cycle or when starting a subsequent wash
cycle prior to the next programme being selected and started.
WARNING: THIS TEMPERATURE MUST NEVER BE
EXCEEDED
10
11
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
TABLE OF PROGRAMMES
PROGRAM FOR:
PROGRAMME
SELECTOR ON:
TEMP.
°C
WEIGHT
MAX
kg
CHARGE
DETERGENT
❙ ❙
❙
❙
❙
❙
❙
Resistant fabrics
Whites
with prewash
9 0 °C
P
Up to
90°
5,5
Cotton, linen
**
Up to
60°
Fast coloureds
5,5
5,5
5,5
❙
6 0 °C
Cotton, mixed
Ple a se re a d the se note s
Up to
40°
Fast coloureds
❙
❙
❙
❙
4 0 °C
3 0 °C
Whe n wa shing he a vily so ile d la und ry it is re c o m m e nd e d the lo a d is re d uc e d to 3 kg
ma ximum .
Up to
30°
Non fast coloureds
** Pro g ra m m e a lso re c o m m e nd e d fo r low te m p e ra ture wa sh (b e low the ind ic a te d
Ma x. te m p e ra ture ). Pro g ra m m e s a c c o rd ing to CENELEC EN 60456.
Mixed fabrics and synthetics
Fast coloureds with
Prewash
Up to
60°
6 0 °C
P
2,5
❙
❙
❙
Mixed, resistant
The sp in sp e e d ma y a lso b e re d uc e d , to ma tc h a ny g uid e line s sug g e ste d o n the fa b ric
la b e l, o r fo r ve ry d e lic a te fa b ric s c a nc e l the sp in c o m p le te ly this o p tio n is a va ila b le
with a sp in sp e e d b utto n.
Up to
50°
**
**
Fast coloureds
❙
❙
❙
❙
Synthetics (nylon,
perlon), mixed cotton
5 0 °C
4 0 °C
2,5
2,5
Up to
40°
Non fast coloureds
The va ria b le te m p e ra ture se le c to r a llows a re d uc tio n in the wa sh te m p e ra ture . Fo r
e xa m p le , a n inte nse c o tto ns c yc le c a n b e wa she d in c o ld wa te r sim p ly b y m oving
the d ia l to the
sym b o l.
Up to
40°
Delicates
❙
❙
1,5
1
4 0 °C
4 0 °C
Very delicate fabrics
Whe n o nly a lim ite d num b e r o f a rtic le s ha ve sta ins whic h re q uire tre a tm e nt with
liq uid b le a c hing a g e nts, p re lim ina ry re m ova l o f sta in c a n b e c a rrie d o ut in the
wa shing ma c hine .
“MACHINE
WASHABLE”
woollens
Up to
40°
❙
❙
❙
❙
Po ur the b le a c h into the liq uid b le a c h c o nta ine r, inse rte d into the c o m p a rtm e nt
3 0 °C
Up to
30°
Hand wash
ma rke d "II" in the d e te rg e nt d ra we r, a nd se t the sp e c ia l p ro g ra m m e "RINSE"
.
1
-
Whe n this p ha se ha s te rm ina te d , turn the p ro g ra m m e se le c to r o n the "OFF" p o sitio n,
a d d the re st o f the fa b ric s a nd p ro c e e d with a no rma l wa sh o n the m o st suita b le
p ro g ra m m e .
Rinse
-
❙
Fast spin
Drain only
-
-
-
-
“Mix & wash” System
programme
Up to
40°
5,5
2
❙
❙
❙
Up to
50°
Rapid 32 minute
12
13
Download from Www.Somanuals.com. All Manuals Search And Download.
“MIX & WASH SYSTEM” PROGRAMME
This is an exclusive Candy system and involves 2 great advantages for the
consumer:
Programme selector
For the various types of fabrics and various degrees of dirt the washing machine has different
programme bands according to: wash cycle, temperature and length of cycle (see table of
washing cycle programmes).
• to be able to wash together different type of fabrics (e.g. cotton + synthetic
etc…) NON-FAST COLOUREDS;
• to wash with a considerable energy saving.
The "Mix & Wash" programme has a temperature of 40°C and alternate
dynamic phases (the drum that turns) to static phases (fabrics in soak in
phase of rest) with the programme duration that almost reaching the 3 hours.
The energy consumption for the complete cycle is only 850 W/h.
1 RESISTANTS FABRICS
The programmes have been designed for a maximum wash and the
rinses, with spin intervals, ensure perfect rinsing.
The final spin gives more efficient removal of water.
Important:
• the first washing of new coloureds fabrics must be done separately;
• in every case, never mix NON-FAST COLOUREDS fabrics.
2 MIXED AND SYNTHETIC FABRICS
The main wash and rinse gives the best results thanks to the rotation
rhythms of the drum and to the water levels.
32 MINUTE RAPID PROGRAMME 50°C
A gentle spin will mean that the fabrics become less creased.
The 32 minute rapid programme allows a complete washing cycle to be
carried out in approximately 30 minutes, with up to a maximum load of 2 kg
and a temperature of 50°C.
3 SPECIAL DELICATE FIBRES
This is a new wash cycle which alternates washing and soaking and is
particularly recommended for very delicate fabrics such as Pure Machine
Washable Wool. The wash cycle and rinses are carried out with high water
levels to ensure best results.
When selecting the "32 minute rapid" programme, please note that we
recommend you use only 20% of the recommended quantities shown on
the detergent pack.
Automatic Variable Capacity
“HAND WASH”
This washing machine also has a gentle Hand Wash programme cycle.
This programme allows a complete washing cycle for garments specified
as “Hand Wash only” on the fabric care label. The programme has a
temperature of 30°C and concludes with 3 rinses and a slow spin.
The washing machine is fitted with an automatic reduction in consumption system (known as
Automatic Variable Capacity).
This system enables the machine to use the amount of water needed to wash and rinse the
laundry in relation to the particular load.
This results in a reduction in the amount of water used and electricity needed to heat it to the
minimum required, without in any way compromising the washing and rinsing performance.
In fact the amount of water and electricity used will always be appropriate for the amount of
washing.
The washing machine therefore ensures you achieve excellent washing results whilst
respecting the environment and saving you money.
4. SPECIALS
SPECIAL “MIXED RINSES” PROGRAMME
This programme carries out three rinses with a intermediate spin. It can be
used for rinsing any type of fabric, eg. use after hand-washing.
This program can be also used as cycle of Bleaching (see table of
washing cycle programmes).
SPECIAL “FAST SPIN” PROGRAMME
Programme “FAST SPIN” carries out a maximum spin.
DRAIN ONLY
This programme drains out the water.
14
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Detergent drawer
Detergents, washing aids and amounts to use
Choice of detergent
The detergent drawer is split into 3 compartments:
- the compartment labelled "I" is for prewash detergent;
- the compartment labelled " " is for special additives,
General purpose detergents
-
-
Powder detergents, for a thorough wash, with bleaching agent, particularly suitable for
use in hot wash programmes (60°C and over), for heavily soiled and stained laundry.
Liquid detergents, particularly suitable for grease stains, such as greasy skin marks,
cosmetics and oil.
fabric softeners, fragrances, starch, brighteners etc;
These detergents are not suitable for washing stained laundry, as they do not contain
bleach.
Biological detergents, not all the products available give a really thorough wash.
- the compartment labelled "II" is for main wash
detergent.
-
If liquid detergents are used, please insert the special
container supplied into the compartment marked “II” in the
detergent drawer. This ensures that the liquid detergent
enters the drum at the right stage of the wash cycle.
Additional laundry aids
-
Water softener, means less detergent can be used where water hardness is classed as
hard to very hard.
-
Prewash substances, for the programmed treatment of stains prior to the main wash.
Using them means the subsequent wash can be at a low temperature or with bleach-free
detergents.
Fabric softener, prevents static build-up in synthetic fabrics and softens fabrics.
If you own a tumble dryer, clothes are softened even without the use of a fabric softener.
This special container must be inserted into the
compartment marked "II" in the detergent drawer, also
when you wish to use the "RINSE" programme as
BLEACHING cycle.
-
NOTE:
Do not put solvents in the washing machine!
Keep detergents and other laundry products out of children’s reach.
Before pouring in the detergent check that there are no foreign bodies in the detergent
drawer.
Some Detergents are Difficult to
utilise. Ensure to use an in drum
dispenser if recommended by
the detergent Manufacturer.
Dosage details are usually shown on the detergent packaging. Follow those instructions.
Note: only put liquid products in the compartment
labelled “
” . The machine is programmed to
automatically take up additives during the final rinse
stage for all wash cycles.
16
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Dosages
Useful advice for users
Only use detergents which are suitable for use in a washing machine.
You will obtain the best results from your wash with the minimum use of chemical products
and the best care for your laundry if you take into consideration the degree of soiling as well
as the type of detergent to choose.
Tips on using your domestic appliance in the most environmentally-friendly and economical
way
The amount of detergent to use depends on:
- water hardness: depending on the hardness of the water and the type of detergent used, it
is possible to reduce the amount of detergent.
Do a full load in your washing machine
To prevent any possible waste of energy, water or detergent we recommend that you put a
full load in your washing machine, not exceed the recommended maximum load size.
Up to 50% energy saving can be made with one full load compared to two half load washes
-
the degree of soiling: it is possible to reduce the amount of detergent used depending on
the degree of soiling.
-
amount of laundry: it is possible to reduce the amount of detergent when washing only a
small amount of laundry.
When is prewashing really needed?
Only with particularly dirty loads!
Energy savings of 5 to 15% are made by not selecting the prewash option for normal soiled
laundry.
Dosage for powder detergent
For normal and low concentration detergents: for normally soiled laundry choose a
programme without prewash.
Which wash temperature should you choose?
Put the detergent in compartment “II” of the drawer.
For heavily soiled laundry, choose a programme with prewash.
Put 1/4 of the detergent in compartment “I”, 3/4 in compartment “II” of the drawer.
When using water softeners, first put in the detergent, then add the softener to compartment “II”.
For highly concentrated detergents not in single dose format, follow what is shown on pack
exactly as regards type and amount of dosage.
Using stain removers before machine washing reduces the need to wash at temperatures
over 60°C.
Energy savings of up to 50% can be made by using a 60°C wash temperature rather than
90°C.
To avoid the difficulty of checking if the detergent has been taken up, use the dosage aids
provided in the detergent packaging.
Liquid detergent dosage
Liquid detergents may be used in accordance with the instructions on the relevant
packaging, for all programmes without prewash, by using the special container which is
placed in the drum or, for those models that have it, in the special insert for liquid detergents.
18
19
Download from Www.Somanuals.com. All Manuals Search And Download.
The correct way to wash
Main wash
Preparing the laundry
Sorting the laundry
A) Select the laundry.
-
It is recommended you wash only items which are machine washable with water and
detergent and not dry-clean items.
Loading the laundry
B) Open the porthole.
-
-
If you need to wash rugs, bedspreads or other heavy items, it is best not to spin them.
C) Put the laundry in the washing machine.
Close the porthole again, ensuring that no items of
laundry are obstructing the lock.
Sort the laundry according to fabric type, degree of soiling and wash temperature: Always
follow the wash care advice on the garment label for the most suitable care and
treatment of the laundry
Putting detergent in machine
Laundry for hot wash
D) Open the drawer, choose the detergent and put in
the correct amount, according to the manufacturer’s
instructions and the advice on page 17.
Add any other laundry aids (see page 17). Close the
drawer again.
Coloured, easy-care materials
Delicates and wool
Wash by hand
Items labelled with the following symbol are not suitable for machine washing:
Dry clean
Selecting the wash programme
For very delicate items, such as net curtains, underwear, tights etc., you are advised to
use a laundry net or wash bag.
Woollen items must be labelled with the "Pure New Wool" symbol to be washed in the
Refer to the programme guide or the programme descriptions on the machine to select the
most suitable programme.
Turning the selector knob, the required programme is activated.
Wait for the “STOP” indicator light to flash.
-
-
machine
, and must also be labelled "non-matting" or "machine washable".
Colour often leaks from new coloured items.
This can then colour other lighter items being washed.
We therefore recommend that coloured items should be washed for the first time
separately.
Press additional function buttons (if required).
For future washes, colourfast items can only be washed with whites up to 40°C.
Check that the tap is turned on and that the discharge hose is positioned correctly.
Press the "Start/Pause" button.
When the "Start/Pause" button is pressed the machine sets the working sequence in motion.
Note: when sorting laundry
-
check there are no metal objects in the laundry
(such as paper clips, safety pins, pins, coins
etc...);
The programme carries out with the programme selector stationary on the selected
programme till cycle ends.
Warning: If there is any break in the power supply while the machine is operating, a special
memory stores the selected programme and, when the power is restored, it continues where
it left off.
-
button up pillowcases, fasten zips, hook & eye
fasteners, belts and long dressing gown cords;
remove curtain hooks;
pay close attention to the labels on items
if you notice stubborn stains whilst sorting the
laundry, remove them using a special detergent or
a special stain remover.
-
-
-
When the programme is finished
At the end of the programme the indicator light “STOP” will go on.
Wait for the door lock to be released (about 2 minutes after the programme has finished).
The "Door Security" indicator light will go out.
-
We recommend that you do not do a full load of towelling items only as these become too
heavy since they absorb a lot of water.
Switch off the machine by turning the programme selector on the “OFF” position. Open the
door and remove the laundry. Turn off the tap.
20
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Investigating malfunctions
Cleaning and routine maintenance
Do not use alcohol-based scourers and / or thinners on the outside of your washing machine,
just a wipe with a damp cloth will suffice. The washing machine needs very little maintenance:
- Cleaning the drawer compartments.
What might be the cause of…
Defects you can remedy yourself
MALFUNCTION CAUSE
REMEDY
- Cleaning the door glass.
1. Does not work on any
programme
Plug not in socket.
Not switched on.
Power failure.
Fuse blown.
Plug it in.
Switch on.
Check.
Cleaning the drawer compartments
Even if it is not strictly necessary, it is good to clean the
compartments for bleaching detergents and additives
occasionally.
Check.
Door open.
Close door.
A) To do this you just need to pull them out firmly, but
without forcing them.
B) Clean everything in the compartment under running
water.
2. Does not fill with water
See cause 1.
Check.
Tap turned off.
Turn on tap.
Programme selector not correctly
positioned.
Fill hoses are kinked
Position programme selector
correctly.
Straighten fill hoses
C) Put everything back in its proper place.
3. Water does not drain
away
Kink in discharge hose.
House drain is blocked
Straighten discharge hose.
Clean drain
Cleaning the door glass
Regularly clean the door glass with a damp cloth. A build
up of soiling and
residues from the water may result in water leaking from
the door.
4. Water on floor around
the washing machine
Leaking gasket between tap and water
inlet hose.
Replace gasket and tighten hose and
tap well.
Clean drain
Clean soap drawer
House drain is blocked
Soap drawer blocked with soap residues
Do not use abrasive cleaners as they can scratch the
surface.
5. Does not spin
Water has not yet drained away.
"No spin" selected (certain models only).
Wait a few minutes for machine to empty.
Reset button or turn "no spin" knob.
6. Machine vibrates a lot
during spin
Washing machine not completely level.
Transit brackets not removed yet.
Load not distributed evenly.
Adjust the special adjustable feet.
Remove transit brackets.
Rearrange the laundry evenly.
Transporting the appliance or long
periods when appliance is not in
use
7. Door will not open
Two minutes have not elapsed since the
programme finished.
Wait two minutes.
If the appliance is being transported or is out of use for
long periods in unheated places, all remaining water
must be completely removed from the hoses.
Ensure mains power is off, then unclip the hose and
point it downwards into a basin until all the water has
emptied out.
The machine makes a
different noise when
spinning! This is because it
has a brush motor for better
performance.
Only a small level of water can be
seen in the drum! This is because
new machines do not use much
water, yet achieve the same
When finished, repeat the operation in the reverse order.
standard of washing and rinsing.
23
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Note:
The use of environmentally-friendly, phosphate-free detergents can have the following effects:
-
-
-
-
waste water from rinsing may be cloudier because of the presence of zeolites held in
suspension, without the rinse performance being adversely affected;
presence of white powder (zeolites) on laundry after washing, which is not absorbed by
the fabric and does not alter the colour of the fabric.
The presence of foam in the final rinsing water is not necessarily an indication of poor
rinsing.
Anionic surfactants used in washing detergent formulae often prove to be difficult to
remove from the laundry itself and, even in small quantities, can still cause considerable
foam production.
-
Carrying out more rinse cycles does not serve any purpose in such cases.
CUSTOMER SERVICE AND GUARANTEE
Fig. 2
Your new appliance is fully guaranteed by the manufacturer for 12 months against
electrical/mechanical breakdown excluding:
A. Any faults which occur due to bad installation or misuse of the machine.
B. Any faults which occur due to repair of, or interference with, the machine by any person
not authorised by the manufacturer to carry out service.
Technical data
❙
Max. load of dry laundry for washing
5,5 kg
0,05 ÷ 0,8 MPa
❙
Water pressure
C. Any faults which arise from parts fitted to the machine which are not the manufacturers
original parts.
D. Any faults arising from non-domestic use or unusual or abnormal use of the machine.
E. Any faults arising from operation at an incorrect voltage.
F. Any faults arising from incorrect operation of the machine.
The guarantee applies to Gt. Britain and Northern Ireland only, and is an addition to your
statutory rights.
Measurements
❙
❙
❙
Width
Depth
Height
60 cm
54 cm
82 cm
NB: For specifications regarding electrical data, see the data panel on the front of the washing
machine (porthole area) - as shown in diagram above.
After Sales Service
If, having investigated the possible malfunctions on the chart on the previous page, you
believe the appliance is not working correctly, please call our After Sales Service dept. on
telephone number:
EC Appliance complies with European Directive 89/336/EEC, 73/23/EEC and
subsequent amendments.
Gias Service
-
Tel: 08705 400 600
(Eire 018301 666)
Support Service
24
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Note: we recommend you keep the transit bracket,
braces and screws to immobilise the machine for future
transit.
The Manufacturers will not be responsible for any
possible damage to the machine caused by not
following the rules relating to releasing the mechanism.
The user is responsible for all costs of installation.
SETTING UP + INSTALLATION
Remove the polystyrene base and place the machine near
its permanent position (diagram 1).
1
2
Carefully cut through the hose retaining clip at the rear of
the appliance (diagram 2).
Unscrew the central bolt (A); unscrew the 4 lateral screws
(B) and remove the cross piece (C).Unscrew the two rods D
and remove them. Two plastic spacers will fall inside the
machine. (diagram 3).
Water connection
Lean the machine forward, remove the mentioned plastic
spacers and remove the plastic bags containing the two
polystyrene blocks at the sides, pulling downwards.
(diagram 4).
Stop the holes using the plugs that you will find inside the
bag containing the instruction booklet. (diagram 5).
The appliance must be connected to the water mains using new
hose-sets.
The old hose-sets should not be re-used.
The machine has an inlet hose with 3/4" B.S.P threaded end
connection to attach between the threaded connector on the
appliance and the cold water supply.
This machine only uses cold water, therefore
only one hose is needed to connect to the cold
water supply. Do not connect to the hot supply.
Cold fill is an energy efficient system. Only the
water required for the washing is heated.There
is no loss of heat in the pipeline from a hot
water tank or boiler to the machine.
3
4
5
D
WARNING:
DO NOT LEAVE THE PACKAGING WITHIN REACH
OF CHILDREN AS IT IS A POTENTIAL
SOURCE OF DANGER.
Apply the insulation sheet of corrugated material to the base
as shown.
min 4 cm
Level the machine using the 4 feet.
A
a) Turn the nut clockwise to release the screw adjuster on the foot.
b) Rotate the foot to raise or lower it until it stands firmly on the
ground.
c) Lock the foot in position by turning the nut
anti-clockwise until it comes up against the bottom of the machine.
+2,6 mt max
min 50 cm
max 85 cm
B
C
26
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Note: it is advisable to turn off the tap after each wash
to isolate the washing machine from the water supply.
For the washing machine to function properly the terminal end of the discharge hose (mouth)
must be at a minimum of 50 cm and a maximum of 85 cm from the ground.
ELECTRICAL CONNECTIONS
After installation, the appliance must be positioned so that the plug is accessible.
If the plug we supply does not fit
CUT IT OFF AND DESTROY IT!
You can’t use it on other appliances, and the exposed wires could be dangerous if plugged in.
To fit a replacement plug, proceed as follows:
Connect
to the terminal in the plug
green and yellow wire
marked with the letter E,
OR marked
with the symbol,
OR coloured green,
OR coloured green and yellow.
blue wire
marked N
OR coloured black.
brown wire
marked L
OR coloured red.
WARNING
This appliance must be earthed
Fuses and plugs
This appliance should be used only on a socket with a minimum rating of 13 Amp.
Our ready-fitted plug is already equipped with a 13 amp fuse which is BS 1362 ASTA
approved. Any replacement should be exactly the same.
If the fuse cover is lost, do not use the plug until it is replaced. A correct replacement fuse
cover (obtainable from your local retailer) must be the same colour as shown or named on
the insert on the base of the plug.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
The manufacturer declines all responsibility in the event of any printing mistakes in
this booklet. The manufacturer also reserves the right to make appropriate
modifications to its products without changing the essential characteristics.
Download from Www.Somanuals.com. All Manuals Search And Download.
This appliance is marked according to the European directive 2002/96/EC on Waste Electrical and Electronic
Equipment (WEEE).
By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the
environment and human health, which could otherwise be caused by inappropriate waste handling of this
product.
The symbol on the product indicates that this product may not be treated as household waste. Instead it shall
be handed over to the applicable collection point for the recycling of electrical and electronic equipment
Disposal must be carried out in accordance with local environmental regulations for waste disposal.
For more detailed information about treatment, recovery and recycling of this product, please contact your
local city office, your household waste disposal service or the shop where you purchased the product.
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
|