See Warranty on page 20 for important information about commercial use of this product.
Operating Instructions and Parts Manual
GW4500
Please read and save these instructions. Read carefully before attempting to assemble, install, operate or maintain the product described.
Protect yourself and others by observing all safety information. Failure to comply with instructions could result in personal injury and/or
property damage! Retain instructions for future reference.
Need
Welder /
Assistance?
Call Us First!
1-800-543-6400
Generator
Unpacking
Table of Contents
After unpacking the welder / generator,
inspect carefully for any damage that
may have occurred during transit. Make
sure to tighten fittings, bolts, etc.,
before putting unit into service. Report
any missing items by calling
Description . . . . . . . . . . . . . . . . . . . . . .1
Unpacking . . . . . . . . . . . . . . . . . . . . . . .1
Safety Guidelines . . . . . . . . . . . . . . . . .1
Specifications. . . . . . . . . . . . . . . . . . . . .1
General Safety Information . . . . . . 2 - 4
Glossary of Terms . . . . . . . . . . . . . . . . .5
Pre-operation . . . . . . . . . . . . . . . . . 6 - 7
Operation . . . . . . . . . . . . . . . . . . . . 7 - 9
Maintenance . . . . . . . . . . . . . . . . . . . . .9
Storage . . . . . . . . . . . . . . . . . . . . . . . . .9
Welding Guidelines. . . . . . . . . . . 10 - 12
1-800-543-6400.
Safety Guidelines
This manual contains information
that is very important to know and
understand. This information is
provided for SAFETY and to PREVENT
EQUIPMENT PROBLEMS. To help
recognize this information, observe the
following symbols.
Specifications
ENGINE
Engine Type . . . . .270cc, 4 stroke OHV
Net Power . . . . . . . . . . . . . . . . . . . . 6.0
Ignition System . . Transistor Magneto
Start Mode. . . . . . . . . . . . . . . . Manual
Fuel Capacity . . . . . . . . . . . 1.4 gallons
Oil Capacity . . . . . . . 38.4 fluid ounces
Troubleshooting Chart . . . . . . . . 13 - 14
General. . . . . . . . . . . . . . . . . . . . . .13
Generator. . . . . . . . . . . . . . . . . . . .13
Welder . . . . . . . . . . . . . . . . . . . . . .14
Welds . . . . . . . . . . . . . . . . . . . . . . .14
Danger indicates an
imminently
hazardous situation which, if not
avoided, WILL result in death or serious
injury.
Wiring Diagram. . . . . . . . . . . . . . . . . .15
Welder / Generator Assembly. . . 16 - 17
Alternator Assembly. . . . . . . . . . 18 - 19
Warranty . . . . . . . . . . . . . . . . . . . . . . .20
Warning indicates a
potentially
hazardous situation which, if not
avoided, COULD result in death or
serious injury.
GENERATOR
Type . . . . . . 2 pole, brushless rotating
Phase . . . . . . . . . . . . . . . . . . . . . Single
Continuous Power
Rating (KVA) . . . . . . . . . . . . . . . . . . 4.5
Rated Voltage (V) . . . . . . . . . 120 / 240
Caution indicates a
potentially
hazardous situation which, if not
avoided, MAY result in minor or
moderate injury.
Description
WELDER
This welder / generator is powered by
an air-cooled four cycle engine and
designed to run at maximum RPM and
give a continuous wattage as rated.
A low-oil level shutoff is provided to
protect the engine. The alternator is
thermostatically protected. To operate
this unit as a generator or welder,
set the switch on the front panel
accordingly.
Max Open Circuit Voltage (V). . . . 62.5
Rated Voltage (V) . . . . . . . . . . . . . 25.6
Rated Current (A) . . . . . . . . . . . . . .140
Max No Load Speed (r/min) . . . . .3850
Current Control Range (A) . . . 60 - 140
Rated Duty Cycle (%) . . . . . . . . . . . .35
Electrode Diameter (mm) . . . . 2.4 - 3.2
Notice indicates
important
information, that if not followed, may
cause damage to equipment.
NOTE: Information that requires special
attention.
REMINDER: Keep your dated proof of purchase for warranty purposes!
Attach it to this manual or file it for safekeeping.
For parts, product & service information
© 2008 Campbell Hausfeld/Scott Fetzer
IN954000AV 8/08
Download from Www.Somanuals.com. All Manuals Search And Download.
GW4500
General Safety Information
(Continued)
•
All persons operating this
•
•
Always attach the work lead first.
equipment or in the area while
equipment is in use must wear
protective welding gear including:
welding helmet or shield with
at least shade 10, flame resistant
clothing, leather welding gloves,
and full foot protection.
Verify that the work piece is
securely grounded.
Always
keep a
fire extinguisher accessible
while performing arc welding
operations.
•
•
•
Always shut off electric arc welding
equipment when not in use and
remove the electrode from the
holder.
•
All installation, maintenance, repair
and operation of this equipment
should be performed by qualified
persons only in accordance with
national, state, and local codes.
Never allow any part of the body to
touch the electrode and ground or
grounded work piece at the same
time.
Never look at arc
welding operations
without eye protection as described
above. Never use a shade filter lens
that is cracked, broken, or rated below
number 10. Warn others in the area not
to look at the arc.
Improper
use of
electric arc welders can cause
electric shock, injury, and
death! Take all precautions
described in this manual to reduce the
possibility of electric shock.
Awkward welding conditions
and positions can be electrically
hazardous. When crouching,
kneeling or at elevations, be sure to
insulate all conductive parts, wear
appropriate protective clothing,
and take precautions to prevent
injury from falls.
Electric
arc
welding operations cause
sparks and heat metal to
temperatures that can cause
severe burns! Use protective gloves and
clothing when performing any metal
working operation. Take all precautions
described in this manual to reduce the
possibility of skin and clothing burns.
•
Verify that all components of the
arc welder are clean and in good
condition prior to operating the
welder. Be sure that the insulation
on all cables, electrode holders,
and power cords is not damaged.
Always repair or replace damaged
components before operating
the welder. Always keep welder
panels, shields, etc. in place when
operating the welder.
•
•
Never attempt to use this
equipment at current settings
or duty cycles higher than those
specified on the equipment labels.
•
Make sure that all persons in the
welding area are protected from
heat, sparks, and ultraviolet rays.
Use additional face shields and
flame resistant barriers as needed.
Never use an electric arc welder to
thaw frozen pipes.
Flying
sparks
•
Never touch work pieces until
completely cooled.
and hot metal can cause
injury. As welds cool, slag
can be thrown off. Take all
precautions described in this manual
to reduce the possibility of injury from
flying sparks and hot metal.
•
•
Always wear dry protective clothing
and welding gloves, and insulated
footwear.
Heat and
sparks
produced during electric arc
welding and other metal
Always operate the welder in a
clean, dry, well ventilated area. Do
not operate the welder in humid,
wet, rainy, or poorly ventilated
areas.
working operations can ignite
flammable and explosive materials! Take
all precautions described in this manual
to reduce the possibility of flames and
explosions.
•
•
Wear ANSI approved face shield
or safety glasses with side shield
protection when chipping or
grinding metal parts.
•
•
Be sure that the work piece is
properly supported and grounded
prior to beginning any electric arc
welding operation.
Wear ear plugs when welding
overhead to prevent spatter or slag
from falling into ears.
•
Remove all flammable materials
within 35 feet (10.7 meters) of
welding arc. If removal is not
possible, tightly cover flammable
materials with fire proof covers.
Electric
arc
Coiled welding cable should be
spread out before use to avoid
overheating and damage to
insulation.
welding operations produce
intense light and heat
and ultraviolet (UV) rays.
This intense light and UV rays can
cause injury to eyes and skin. Take all
precautions described in this manual to
reduce the possibility of injury to eyes
and skin.
•
•
Take precautions to be sure that
flying sparks and heat do not cause
flames in hidden areas, cracks,
behind bulkheads, etc.
Never immerse the
electrode or
electrode holder in water. If the
welder becomes wet for any reason, be
absolutely certain that it is completely
clean and dry prior to attempting use!
Do not use any part of the unit as a
work surface.
•
Always shut the equipment off
prior to moving the unit.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating Instructions and Parts Manual
ADDITIONAL SAFETY STANDARDS
General Safety Information
(Continued)
The
ANSI Standard Z49.1 from American
Welding Society, 550 N.W. LeJune Rd.
Miami, FL 33126
electromagnetic field that
is generated during arc
Fire
hazard!
welding may interfere with
the operation of various electrical
and electronic devices such as cardiac
pacemakers. Persons using such devices
should consult with their physician prior
to performing any electric arc welding
operations.
Do not weld on containers
or pipes that contain or
have contained flammable
materials or gaseous or liquid
combustibles.
Safety and Health Standards
OSHA 29 CFR 1910, from Superintendent
of Documents, U.S. Government Printing
Office, Washington, D.C. 20402
Arc
National Electrical Code
welding
closed cylinders or containers
such as tanks or drums
can cause explosion if not
properly vented! Verify that any
cylinder or container to be welded has
an adequate ventilation hole, so that
expanding gases can be released.
•
Route the electrode and work
cables together and secure with
tape when possible.
NFPA Standard 70, from National Fire
Protection Association, Batterymarch
Park, Quincy, MA 02269
•
•
Never wrap arc welder cables
around the body.
Safe Handling of Compressed Gases in
Cylinders
Always position the electrode and
work leads so that they are on
the same side of the body.
CGA Pamphlet P-1, from Compressed
Gas Association, 1235 Jefferson Davis
Highway, Suite 501, Arlington, VA 22202
Do not
breathe
fumes that are produced by
the arc welding operation.
These fumes are dangerous.
If the welding area cannot be
adequately ventilated, be sure to use an
air-supplied respirator.
•
Exposure to electromagnetic fields
during welding may have other
health effects which are not known.
Code for Safety in Welding and Cutting
CSA Standard W117.2, from Canadian
Standards Association, Standards
Sales, 178 Rexdale Boulevard, Rexdale,
Ontario, Canada M9W 1R3
Always be sure that
the welding area
•
Keep the head and face out of the
welding fumes.
is secure and free of hazards (sparks,
flames, glowing metal or slag) prior to
leaving. Be sure that the equipment is
turned off and electrode is removed. Be
sure that cables are loosely coiled and
out of the way. Be sure that all metal
and slag has cooled.
Cutting And Welding Processes
•
Do not perform electric arc welding
operations on metals that are
galvanized or cadmium plated, or
contain zinc, mercury, or beryllium
without completing the following
precautions:
NFPA Standard 51B, from National Fire
Protection Association, Batterymarch
Park, Quicy, MA 02269
Safe Practices For Occupational And
Educational Eye And Face Protection
ANSI Standard Z87.1, from American
National Standards Institute, 1430
Broadway, New York, NY 10018
Refer to the Material Safety Data Sheets
and the manufacturers instructions
for metals, electrodes, coatings and
cleaners.
a. Remove the coating from the
base metal.
b. Make sure that the welding area
is well ventilated.
c. Use an air-supplied respirator.
Extremely toxic fumes are created when
these metals are heated.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
GW4500
Flux Cored Arc Welding (FCAW) -
also called Gasless, is a welding process
used with a wire-feed welding machine. other contaminants while the weld is
The weld wire is tubular with flux
Slag - a layer of flux soot that
protects the weld from oxides and
Getting To Know Your
Welder / Generator
Glossary of Terms
AC or Alternating Current - electric
current that reverses direction
periodically. Sixty cycle current travels in
both directions sixty times per second.
solidifying (cooling). Slag should be
removed after weld has cooled.
material contained inside for shielding.
Gas Metal Arc Welding (GMAW) -
also called MIG, is a welding process
used with a wire feed welding machine.
The wire is solid and an inert gas is used
for shielding.
Spatter - metal particles thrown from
the weld which cool and harden on the
work surface. Spatter can be minimized
by using a spatter resistant spray on the
work piece before welding.
Arc Length - the distance from the
end of the electrode to the point where
the arc makes contact with the work
surface.
Gas Tungsten Arc Welding (GTAW) -
also called TIG, is a welding process used proper alignment until final welds are
Tack Weld - weld made to hold parts in
Base Metal - the material to be
welded.
with welding equipment with a high
frequency generator. The arc is created
between a non-consumable tungsten
electrode and the work piece. Filler
metal may or may not be used.
made.
Travel Angle - the angle of the
electrode in the line of welding. It varies
from 5º to 45º depending on welding
conditions.
Butt Joint - a joint between two
members aligned approximately in the
same plane.
Lap Joint - a joint between two
overlapping members in parallel planes.
Crater - a pool, or pocket, that is
formed as the arc comes in contact with
the base metal.
T Joint - made by placing the edge of
one piece of metal on the surface of
the other piece at approximately a 90º
angle.
Open Circuit Voltage (OCV) - the
voltage between the electrode and the
work clamp of the welding machine
when no current is flowing (not
welding). The OCV determines how
quickly the arc is struck.
DC or Direct Current - electric current
which flows only in one direction.
The polarity (+ or -) determines which
direction the current is flowing.
Undercut - a condition that results
when welding amperage is too high.
The excessive amperage leaves a groove
in the base metal along both sides of
the bead which reduces the strength of
the weld.
DC Reverse Polarity - occurs when the
electrode holder is connected to the
positive pole of the welding machine.
Reverse Polarity directs more heat
into melting the electrode rather than
the work piece. It is used on thinner
material.
Overlap - occurs when the amperage is
set too low. In this instance, the molten
metal falls from the electrode without
actually fusing into the base metal.
Weld Pool or Puddle - a volume of
molten metal in a weld prior to its
solidification as weld metal.
Porosity - gas pockets, or cavities,
formed during weld solidification. They
weaken the weld.
Weld Bead - a narrow layer or layers of
metal deposited on the base metal as
the electrode melts. Weld bead width
is typically twice the diameter of the
electrode.
DC Straight Polarity - occurs when
the electrode holder is connected to the
negative pole of the welding machine.
With straight polarity more heat is
directed to the work piece for better
penetration on thicker material.
Penetration - the depth into the work
piece that has been heat effected by
the arc during the welding process. A
good weld achieves 100% penetration
meaning that the entire thickness of
the work piece has been heated and
resolidified. The heat effected area
should be easily seen on the opposite
side of the weld.
Work Angle - the angle of the
electrode from horizontal, measured at
right angles to the line of welding.
Electrode - a coated metal wire having
approximately the same composition as
the material being welded.
Fillet Weld - approximately a triangle
in cross-section, joining two surfaces at
right angles to each other in a lap, T or
corner joint.
Shielded Metal Arc Welding
(SMAW) - also called Stick, is a welding
process that uses a consumable
electrode to support the arc. Shielding
is achieved by the melting of the flux
coating on the electrode.
Flux - a coating, when heated, that
produces a shielding gas around the
welding area. This gas protects the
parent and filler metals from impurities
in the air.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating Instructions and Parts Manual
GROUNDING
3. Rotate the engine switch to the ON
position.
Pre-Operation
1. Use the ground terminal and wing
nut on the welder / generator frame
to connect the unit to a suitable
ground source. Securely fasten the
end terminal of the ground wire to
the ground terminal on the
LOCATION
4. Adjust the choke lever as follows:
Selecting the proper location can
significantly increase performance,
reliability and life of the arc welder.
a. For cold engine, move the choke
lever as far as possible to the left,
choke fully ON, position.
•
•
For best results locate the welder /
generator in an environment that is
clean and dry. Dust and dirt in the
unit retain moisture and increase
wear of moving parts.
b. For warm / hot engine, move the
choke lever midway between the
choke and run positions.
welder / generators frame. Tighten
the washer and wing nut on top of
the ground wire end terminal.
2. The ground wire should be made
of #8 gauge wire. Do not use wire
with a higher gauge number.
5. Pull the starter rope with a brisk,
smooth motion.
Store electrodes in a clean, dry
location with low humidity to
preserve the flux coating.
NOTE: Some models may be
equipped with an electric starter.
For models equipped with an
electric starter, turn the key.
Higher gauge numbers indicate
thinner wire, which may not
provide an adequate ground path.
INSTRUCTIONS
1. Check engine oil level. Oil is NOT
mixed with the gasoline, however
adequate oil supply is necessary for
proper engine lubrication. Refer to
the Engine Manual for SAE, API and
fill quantity specifications. Unit is
shipped without oil in engine.
3. The other end of the ground wire
must be securely fastened to an
approved ground source.
6. After each start up, allow the
engine to run for 2-3 minutes with
no load.
The following are ground sources
approved by the National Electric
Code. Other ground sources may be
acceptable. Refer to the National
Electric Code and local regulations for
further ground source information. If
not sure of regulations or procedures,
obtain assistance from a qualified
(licensed or certified) electrical
technician.
7. As the engine warms up and
stabilizes, adjust the choke lever
to the right, until the lever is
positioned as far as possible to the
right.
2. Use of a Ground Fault Interrupter
(GFI) is strongly recommended.
Ground Fault Interrupters can
significantly reduce the possibility
of injury if an electrical short occurs.
In order to install a GFI, the
Engine speed is
preset to provide
proper output voltage. Never attempt
to modify or adjust engine speed or
output voltage.
welder / generators neutral wire
must be internally grounded to the
welder / generators frame, and the
frame must be properly grounded
to the earth.
ENGINE BREAK-IN
a. An underground water pipe at
least ten feet in length
b. A non-corrosive underground
pipe at least eight feet in length
and 3/4 inch diameter
c. A steel or iron underground rod
at least eight feet in length and
5/8 inch diameter
d. A non-ferrous rod at least
eight feet in length, 1/2 inch
in diameter, and approved for
grounding purposes
After initial start-up, the engine
should be broken in according to the
manufacturer's instructions. Refer to the
engine manual for the proper break-in
procedure.
A Ground Fault
Interrupter may
not be effective if used on a welder /
generators that is not grounded! Refer
to the section entitled Grounding for
proper steps to ground the welder /
generator.
SHUT-OFF
1. Shut off and remove all electrical
load devices from the welder /
generator.
3. When installing a GFI, be sure
to follow all national and
2. Allow the engine to run for 2-3
minutes with no electrical loads.
local regulations. If not sure of
regulations or procedures, obtain
assistance from a qualified (licensed
or certified) electrical technician.
Any rod or pipe used for grounding
must be driven to eight feet deep or
buried in the deepest possible trench.
3. Rotate the engine switch to the OFF
position.
4. Verify that the welder / generator
has completely stopped.
STARTING
1. Remove all electrical loads from the
welder / generators.
5. Close the fuel supply valve.
6. Allow the unit to cool before
installing any covers.
2. Move fuel shut-off lever as far as
possible to the right to enable fuel
flow.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
GW4500
combination of 240 volt loads and
also with 120 volt loads through
the 120 volt receptacles.
If actual watt ratings are not available,
the Power Usage Chart, see Table 1, may
be used as a general guideline.
Pre-Operation (Continued)
LOW OIL SHUTDOWN
A low oil shutdown switch is provided
to protect the engine and welder /
generators on most extended run
models. When engine oil level drops
too low for proper engine operation,
the low oil shutdown switch causes the
engine to shut off. If oil level is low
when attempting to start the welder /
generators engine, the low oil level
shutdown switch prevents the engine
from starting. If engine does not start,
check oil level.
The 120/240 volt twist lock
receptacle, found on some welder /
generators, is rated for 20 amps and incandescent light bulbs, motors and
may be used in any combination of
120 volt and 240 volt loads.
Remember that devices which generate
heat during operation such as heaters,
hair dryers have a higher power draw
than devices which generate little heat
during operation such as florescent
bulbs, radios, and clocks.
4. Individual receptacles should not
be loaded beyond the amperage
rating.
Long power cords and extension cords
also draw additional power. Keep cords
at minimum possible length.
5. Total combined load through any
combination of receptacle must
not exceed the rated load limits of
the welder / generator. Refer to the
identification plate on the welder /
generators for amp and wattage
specifications.
Refer to Table 2 for maximum limits for
lengths of extension cords.
NOTE: It is important to keep the
welder / generator unit on a level
surface. The oil level shutdown switch
can prevent the engine from starting
even if oil level is sufficient, when the
welder / generators unit is placed on an
uneven surface.
8. Circuit protection is provided by a
circuit breaker. The circuit breaker
opens when the welder / generator
load exceeds its maximum capacity
or a short circuit occurs. If the
circuit breaker opens, perform the
following procedures to correct the
problem:
6. Always shut off and remove loads
before starting or shutting off the
welder / generator engine.
7. When plugging multiple electrical
load devices into the welder /
Generator Operation
(FRONT PANEL SWITCH MUST BE SET TO
GENERATOR POSITION)
generators receptacles, be sure to
connect and activate the highest
power draw item first. Allow
the welder / generator engine to
stabilize, then connect and activate
the next highest power draw
device. The smallest power draw
device should be connected to the
receptacle and activated last.
a. Shut off and disconnect all
electrical loads.
LOAD DEVICES
b. Attempt to determine the cause
of the electrical problem -
overloading or short circuit.
c. Do not use any devices that have
short circuits. Avoid overloading
the welder / generator.
d. Press the circuit breaker
pushbutton to reset the circuit
breaker.
1. All load devices and extension cords
should use three prong terminals.
Refer to Table 2 for extension cord
and cable size requirements.
2. Allow the engine to run for 2-
3 minutes before applying any
electrical loads.
NOTE: Power draw can be calculated
by multiplying volts and amps. The
resulting number is wattage.
3. The 120 volt receptacles are rated
for 20 amps and may be used in any
combination of 120 volt loads and
also with 240 volt loads through
the 240 volt receptacles.
Repeated cycling of
the circuit breaker
Never exceed the posted maximum
wattage for the welder / generator
or any individual receptacle. Refer to
owner's manuals and product tags to
determine the wattage of all electrical
load devices.
indicates a problem and may cause
damage to the welder / generators or
load devices. Do not operate the
welder / generators if repeated cycling
of the circuit breaker occurs.
The 240 volt receptacles, found on
some welder / generators, are rated
for 20 amps and may be used in any
TABLE 1 - ESTIMATED POWER USAGE (WATTS)
LOAD DEVICE
WATTS
LOAD DEVICE
WATTS
LOAD DEVICE
WATTS
LOAD DEVICE
WATTS
Air conditioner
2000-3000
Electric drill
(large)
500-1000
Radio
50-200
Toaster
900-1700
Automatic
washer
150-1500
100+
Fan
40-200
Refrigerator
190-2000
Vacuum cleaner
200-300
Brooder
Freezer
300-500
330-1100
500-1500
AS RATED
Skillet
1200
Water pump
1000-3000
1000-5000
1000-2000
1500-2500
Clothes dryer
Coffee maker
5000-10,000 Hot plate
Space heater
Sump pump
Television
600-4800
400-3000
200-500
Water heater
Small hand saw
Large hand saw
400-700
Iron
Electric drill
(small)
225-1000
Light bulb
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating Instructions and Parts Manual
Generator Operation
(Continued)
Welder Operation
(FRONT PANEL SWITCH MUST BE SET TO
WELDER POSITION)
INSTALLATION FOR STAND-BY USE
Precautions must be taken to prevent
electrical back feeding into utility
systems. This requires isolation of
the electrical system. To isolate the
electrical system, perform the following
procedures:
WELDING LEAD ASSEMBLIES
Welding leads assemblies are not
included with all units. Use copper
welding cables in the size specified in
Table 3.
GROUND CLAMP (SEE FIGURE 1)
1. Strip 1/2 inch of insulation from the
end of one of the welding cables.
1. Turn off the main electrical system
switch prior to connecting the
welder / generators.
2. Loosen hex nuts on work clamp.
2. In accordance with national and
local standards, a double throw
transfer switch must be installed in
the system.
3. Insert the end of the welding cable
through clamp handle and slide the
bare wire under the clamp block.
Figure 1
Wire Handle
Sleeve
4. Tighten the hex nuts, securing the
cable in place.
Welding
Cable
Always shut off
main power prior to
temporary connection of the welder /
generators to a building electrical
system.
ELECTRODE HOLDER (SEE FIGURE 2)
1. Strip 1/2 inch of insulation from the
end of the other welding cable.
Slide the bare wire into the wire
sleeve.
Cable Setscrew
Handle Phillips Head Screw
Installation of the
welder / generator
as a backup electrical source must be
performed by a qualified (licensed or
certified) electrical technician.
Electrode Holder
Figure 2
2. Loosen the phillips head screw
a few turns. Do not remove it
completely. Pull the insulated
handle off of the electrode holder,
and slide it over the welding cable.
3. Loosen the set screw on the bottom
of the electrode holder.
4. Insert the welding cable / wire
sleeve into the back of the brass
body of the electrode holder.
TABLE 2 - EXTENSION CORDS
Maximum Recommended Lengths (in feet)
Amps
2.5
5
Watts 120 V
300
Watts 240 V
600
#8 Wire
#10 Wire
1000
500
#12 Wire
600
#14 Wire
375
#16 Wire
250
600
1200
300
200
125
7.5
10
900
1800
350
200
125
100
1200
1800
2400
3000
3600
4800
2400
250
150
100
50
15
3600
150
100
65
20
4800
175
150
125
90
125
75
50
25
6000
100
60
30
7200
65
40
9600
TABLE 3 - WELDING CABLES
Total Cable Length *
0 - 20 feet (0 - 6 m)
20 - 40 feet (6 - 12 m)
40 - 60 feet (12 - 18 m)
Maximum Welding Current
Recommended Sizes of Copper Welding Cables
6 AWG (15 mm2)
100 A
150 A
200 A
250 A
6 AWG (15 mm2)
6 AWG (15 mm2)
4 AWG (20 mm2)
3 AWG (25 mm2)
4 AWG (20 mm2)
2 AWG (35 mm2)
1 AWG (40 mm2)
1/0 AWG (55 mm2)
3 AWG (25 mm2)
2 AWG (35 mm2)
2 AWG (35 mm2)
* Total cable length is the sum of the ground and electrode cable lengths.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
GW4500
If heating, welding,
or cutting materials
that are galvanized, zinc plated,
lead, or cadmium plated refer to the
General Safety Information Section for
instructions. Extremely toxic fumes are
created when these metals are heated.
STORAGE
Welder Operation
(Continued)
5. Tighten the set screw, securing the
cable in place.
If the welder / generators is not to be
used for extended periods of time,
the following pre-storage procedures
should be performed:
6. Slide the insulated handle onto
the electrode holder and tighten
the phillips head screw. Do not
overtighten the phillips head
screw. Overtightening will
1. Make sure engine oil is filled to the
proper level.
2. Connect the work clamp to the
work piece. Make sure the contact
is on bare metal and not obstructed
by paint, varnish, corrosion, or non-
metallic materials.
2. Drain all fuel from the tank, lines,
carburetor and fuel valve.
damage the insulated handle.
3. Remove the spark plug, and pour
approximately one teaspoon of oil
into the spark plug hole.
DINSE PLUGS (SEE FIGURE 3)
1. Strip 1/2 inch of insulation from the
opposite end of the welding cable.
3. Insert the exposed part of the
electrode (the end with no flux)
into the jaws of the electrode
holder.
4. Pull the starter cord several times
to spread the oil throughout the
cylinder.
2. Insert this end of the welding cable
through the dinse plug boot and
slide the bare wire into the wire
sleeve.
4. Set the amperage adjustment knob
to the proper amperage for the
electrode diameter. Refer to the
chart on the front panel for proper
electrode current settings.
5. Slowly pull the starter cord, until
resistance is felt. This indicates that
the piston is moving upward on the
compression cycle, and the intake
and exhaust valves are closed. (The
piston pushes a small amount of
air from the spark plug hole on
compression.)
3. Insert the welding cable/wire sleeve
assembly into the back of the dinse
plug.
The electrode holder
and rod are
electrically “live” (current potential)
when the engine is running.
4. Tighten the set screw, securing the
cable in place.
5. Slide the boot over the hex portion
of the dinse plug.
5. Position the electrode to begin
weld, lower the welding helmet or
position the hand shield, and strike
an arc. Adjust weld amperage as
needed.
6. Use of fuel stabilizers or anti-
gumming agents in the fuel system
can help prevent the build up of
gum and varnish.
6. Repeat for the other lead.
Boot
Set Screw
Whenever the welder / generator is
stored, be sure that the fuel shut-off
valve is in the closed position.
Welding
Cable
6. When finished welding, turn
engine off and store unit properly.
Refer to the engine manual that
accompanies this unit for instructions
regarding maintenance of engine
components.
DUTY CYCLE / THERMOSTATIC
PROTECTION
Wire Sleeve
Welder duty cycle is the percentage of
actual weld time that can occur in a ten
minute interval. For example, at a 10%
duty cycle, actual welding can occur for
one minute, then the welder must cool
for nine minutes.
Dinse Plug
Figure 3
Never tamper with
engine speed
settings or welder / generators
frequency settings. Any governor
adjustments should be made by
qualified personnel only.
Welding
1. Verify that the surfaces of metals
to be joined are free from dirt,
rust, paint, oil, scale or other
contaminants. These contaminants
make welding difficult and cause
poor welds.
Internal components of this welder are
protected from overheating with an
automatic thermal switch.
WELD CABLES
1. Check condition of weld cables and
immediately repair or replace any
cables with damaged insulation.
Maintenance
INFREQUENT USAGE
All persons
operating this
2. Check condition of electrode holder
insulating pieces and immediately
replace cracked or missing parts.
If the welder / generator is used
infrequently, starting difficulty may
occur. To help prevent this, the
welder / generators should be run for
approximately 30 minutes per week.
equipment or in the area while
equipment is in use must wear
protective welding gear including: eye
protection with proper shade (minimum
shade 10), flame resistant clothing,
leather welding gloves, and full foot
protection.
EVERY 3 MONTHS
Replace any unreadable labels on the
welder. Use compressed air to blow
all dust and lint from the ventilation
openings.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating Instructions and Parts Manual
STRIKING AN ARC
3. E-7014 Fast fill
Welding Guidelines
GENERAL
Place the bare end of the electrode in
the holder. Grip the holder lightly to
reduce tiring of the hand and arm.
•
•
Smooth bead and fast deposition
This line of welding machines utilizes
a process known as Shielded Metal-Arc
Welding (SMAW). This process is used
to bond metals by heating them with
an electric arc created between the
electrode and the work piece.
Ideal for joints with poor fitup and
general repair work.
NOTE: Always keep the jaws of the
holder clean to insure good electrical
contact with the electrode.
4. E-7018-AC High Strength
•
Ideal for pipes and structural
applications.
Be careful not to
touch the work piece
•
Low hydrogen reduces porosity for
a strong weld.
Electrodes used for shielded metal arc
welding have two parts. The inner
core is a metal rod or wire that should
be similar in composition to the base
metal. The outer coating is called
flux. Various types of flux exist. Each
coating is used for a particular welding
situation.
or welding bench with the electrode as
this causes arc flashes.
NOTE: Only the E-7018-AC electrode
is recommended for use with these
welders. Other E-7018 electrodes are
designed for use with higher open
circuit voltages than these welders are
capable of producing. Recommended
electrode diameter is 3/32 inch or 1/8
inch.
The best method of striking an arc is the
scratching method. Drag the electrode
at an angle along the surface much like
striking a match. Upon contact with the
plate, lift the electrode approximately
1/16” off the surface or it will stick (See
Figure 5).
While the metal is molten, it can be
contaminated by elements in the air.
This contamination could weaken
the weld. The flux coating creates
a protective barrier called slag that
protects the molten metal from
contaminants.
NOTE: Should the electrode stick to the
work piece, break it loose by quickly
twisting or bending at the holder
while pulling upward. If the electrode
does not break loose, disengage the
electrode by releasing it from the
holder.
ARC WELDING BASICS
Four basic techniques affect weld
quality. These are: amperage setting,
weld angle, arc length, and travel
speed. Proper use of these techniques is
necessary for good weld quality.
When current (amperage) flows
through the circuit to the electrode, an
arc is formed between the end of the
electrode and the work piece. The arc
melts the electrode and the work piece.
The melted metal of the electrode flows
into the molten crater and forms a bond
with the work piece as shown in
Figure 4.
AMPERAGE SETTING
The correct amperage involves the
adjustment of the welding machine
to the required amp setting. This is
regulated by a knob on the welder. The
amperage required depends on the size
(diameter) of electrode used and the
thickness of the work piece.
1/16 inch
NOTE: Discontinue using and discard
electrodes that burn down to 1 to 2
inches from the electrode holder.
Same as Electrode Diameter
Consult specifications listed on the
welder. Excessive amps burn through
light metals and the weld bead is flat
and porous (See Figure 7). The bead
appears high and irregular if the
amperage is too low.
Figure 5 - Scratching Method
Wire
ELECTRODE TYPE AND SIZE
Four types of electrodes are
Flux
recommended for this welder. The
electrodes are commonly known by
the AWS (American Welding Society)
designation as follows:
WELD ANGLE
Slag
Weld
Weld angle is the angle at which the
electrode is held during the welding
process. Using the correct angle
ensures proper penetration and bead
formation. Electrode angle involves
two positions - travel angle and work
angle (See Figure 6).
Crater
1. E-6011 Deep penetrating
•
Flat bead with deep penetrating
arc.
Work Piece
•
For rusted or dirty mild steel
general repair work.
Figure 4 - Weld Components
Travel angle is the angle in the line
of welding and may vary from 5º to
45º from the vertical, depending on
welding conditions.
2. E-6013 General Purpose
•
All position, smooth deposit rod
with low spatter.
•
For all mild steel and general
purpose work.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
GW4500
an arc does not create enough heat to
melt the work piece, the electrode has
a tendency to stick, penetration will be
poor, and uneven beads with irregular
ripples result. A proper arc should be no
longer than the diameter of the rod.
Welding Guidelines
(Continued)
Work angle is the angle from
horizontal, measured at right angles to
the line of welding.
5º - 45º
For most applications, a 45º travel
angle and 45º work angle is sufficient.
For specific applications, consult an arc
welding handbook.
The sound of a proper arc is a steady,
crisp sizzle, similar to bacon frying.
Travel Angle
TRAVEL SPEED
NOTE: Right handed welders should
weld from left to right. Left handed
welders should weld from right to left.
The electrode should always point into
the weld puddle as shown.
The travel speed is the rate at which
the electrode is moved across the weld
area (See Figure 7). When the speed is
too fast, the bead is narrow and bead
ripples are pointed as shown. When the
speed is to slow, the weld metal piles
up and the bead is high and wide. To
control travel speed, watch the width
of the weld bead (not the arc) when
welding. The weld bead is the orange,
molten metal behind the arc. The width
should be approximately twice the
diameter of the welding rod. Control
travel speed to obtain a consistent bead
width.
ARC LENGTH
Arc length is the distance from the
work piece to the tip of the electrode,
the distance which the arc must travel.
A proper arc length is essential to
generate the heat needed for welding
(See Figure 7). An arc that is too long
produces an unstable arc, reduces
penetration, increases spatter, and
causes flat and wide beads. Too short
Work Angle
Figure 6 - Weld Angle
W
NOTE: Weld bead
Work Piece
width (W) should be
approximately twice
the diameter for the
electrode rod used.
Normal Amps,
Arc Length,
Speed
Speed Too Fast
Amperage Too Low
Amperage Too High
Speed Too Slow
Arc Length Too Long
Arc Length Too Short
Figure 7 - Weld Appearance
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating Instructions and Parts Manual
All work should be performed in the
flat position if possible. For specific
applications, consult an arc welding
handbook.
4. If there is no change in lamp
brightness when polarity is
reversed, the diodes must be
replaced.
Welding Guidelines
(Continued)
SLAG REMOVAL
Wear ANSI approved
safety glasses (ANSI
Standard Z87.1) and protective clothing
when removing slag. Hot, flying debris
can cause personal injury to anyone in
the area.
For testing of rotor,
WELD PASS
stator, or field
windings, consult an authorized service
center.
Sometimes more then one pass is
necessary to fill the joint. The root pass
is first, followed by filler passes and the
cover pass (See Figures 8 and 9). If the
pieces are thick, it may be necessary to
bevel the edges that are joined at a 60º
angle. Remember to remove the slag
before each pass.
After completing the weld, wait for the
welded sections to cool. A protective
coating called slag now covers the weld
bead which prevents contaminants in
the air from reacting with the molten
metal. Once the weld cools to the point
that it is no longer glowing red, the slag
can be removed. Removal is done with
a chipping hammer. Lightly tap the slag
with the hammer and break it loose
from the weld bead. The final clean-up
is done with a wire brush. When making
multiple weld passes, remove the slag
before each pass.
TESTING WELDER / GENERATOR
DIODES
The following method eliminates the
need to disconnect the diodes from the
welder / generators wiring.
1. Use a 12 Volt battery and
automotive lamp (Type 5001) to
test the diodes in the welder /
generators.
WELDING POSITIONS
2. Connect the battery and lamp as
shown in Figure 10.
Four basic welding positions can be
used; flat, horizontal, vertical, and
overhead. Welding in the flat position
is easier than any of the others because
welding speed can be increased, the
molten metal has less tendency to run,
better penetration can be achieved, and
the work is less fatiguing.
3. If the diodes are operating
properly, the lamp illuminates
brightly when the battery polarity is
correct, and goes dim when battery
polarity is reversed.
Other positions require different
techniques such as a weaving pass,
circular pass, and jogging. A higher
skill level is required to complete these
welds.
Lamp On
Cover
Filler
Root
Lamp Off
Figure 8 - Weld Passes
Figure 9 - Multiple Weld Passes
Figure 10 - Diode Test Procedure
12
Download from Www.Somanuals.com. All Manuals Search And Download.
GW4500
Troubleshooting Chart - General
Symptom
Possible Cause(s)
Corrective Action
Engine will not start 1. Engine switch is set to "OFF".
2. Fuel valve is turned to "CLOSE".
3. Choke is open.
1. Set engine switch to "ON".
2. Turn fuel valve to "OPEN" position.
3. Close the choke.
4. Engine is out of gas.
4. Add gas.
5. Engine is filled with contaminated or
old gas
5. Change the gas in the engine.
6. Spark plug is dirty.
6. Clean spark plug.
7. Spark plug is broken.
7. Replace spark plug.
8. Unit is not on level surface.
8. Move unit to a level surface to prevent low oil shutdown from
triggering.
9. Oil is low.
9. Add or replace oil.
Engine runs but
there is no electrical
output
1. Circuit reset button is off.
1. Wait for 2 minutes and push the circuit reset button to the "ON"
position.
2. If you are using an extension cord, try a different one.
3. Try connecting a different device.
2. Bad connecting of wires / cables.
3. Bad electrical device connected to
generator / welder.
Generator / welder
runs but does not
support all electrical
devices connected.
1. Generator / welder is overloaded
1. Turn off all electrical devices. Unplug all electrical devices. Turn off
generator / welder. Wait several minutes. Restart generator / welder.
Try connecting fewer electrical loads to the generator / welder.
2. Short in one of the connected devices. 2. Try disconnecting any faulty or short-circuited electrical loads.
3. Air cleaner is dirty.
3. Clean or replace air cleaner.
Troubleshooting Chart - Generator
Symptom
Possible Cause(s)
Corrective Action
No output voltage
1. Engine speed is too slow
2. Open, shorted, or incorrect wiring
3. Faulty capacitor
1. Adjust engine speed ★
2. Referring to the wiring diagram, clean and reconnect all wiring ★
3. Replace capacitor ★
4. Open or shorted field windings
5. Open diodes
6. Front panel switch set incorrectly
7. Circuit breaker tripped
4. Test winding resistance, replace field winding if necessary ★
5. Test diodes, replace if necessary ★
6. Set front panel switch to generator
7. Reset circuit breaker
Low output voltage 1. Engine speed is too slow
1. Adjust engine speed ★
with no load
2. Open diodes
3. Faulty capacitor
2. Test diodes, replace if necessary ★
3. Replace capacitor ★
4. Open or shorted field windings
5. Voltage setting on front panel
incorrect
4. Test winding resistance, replace field winding if necessary ★
5. Adjust setting on front panel
High output voltage 1. Faulty capacitor
with no load 2. Engine speed is too fast
1. Replace capacitor ★
2. Adjust engine speed ★
3. Adjust setting on front panel
3. Voltage setting on front panel
incorrect
Low output voltage 1. Open diode
1. Test diodes, replace if necessary ★
2. Adjust engine speed ★
under load
2. Engine speed too slow at full load
3. Excessive load applied
4. Voltage setting on front panel
incorrect
3. Reduce the applied load
4. Adjust setting on front panel
Erratic output
voltage
1. Unbalanced engine
2. Dirty, corroded, or loose wiring
connection
1. Refer to engine manual
2. Referring to the wiring diagram, clean and reconnect all wiring ★
3. Unstable load applied
3. Remove all loads, then apply each one individually to determine which
one is causing erratic function
Noisy operation
1. Loose welder / generators or engine
bolt
1. Tighten all mountings
2. Short circuit in welder / generators
field or load
3. Faulty bearing
2. Test winding resistance, replace field winding if necessary ★
Test load devices for shorts. Replace defective load device.
3. Replace bearing
★ These diagnostic and repair procedures should be performed by an authorized service center.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating Instructions and Parts Manual
Troubleshooting Chart - Welder
Symptom
Possible Cause(s)
Corrective Action
Welder runs but
does not weld
1. Inadequate current at electrode
1. Check work clamp, cable and connection to work piece. Check
electrode cable and clamp
2. Poor connections at welder
3. Front panel switch set incorrectly
4. Open, shorted, or incorrect wiring
5. Faulty capacitor
2. Check all welder external connections
3. Set front panel switch to weld
4. Referring to the wiring diagram, clean and reconnect all wiring ★
5. Replace capacitor ★
6. Open or shorted field windings
7. Open diodes
6. Test winding resistance, replace field winding if necessary ★
7. Test diodes, replace if necessary ★
Welder gives trickle 1. Accidental contact with work piece
1. Avoid contact with work piece
shocks
2. Current leakage caused by moist
clothing or work area
2. Make sure clothing and work area are dry
Arc difficult to strike 1. Wrong type of electrode.
2. Electrode diameter too large
1. Verify that electrode is for alternating current (AC)
2. Use smaller diameter electrode
3. Work piece not properly grounded
4. Engine speed is too slow
3. Verify proper grounding. (No paint, varnish or corrosion)
4. Adjust engine speed
★ These diagnostic and repair procedures should be performed by an authorized service center.
Troubleshooting Chart - Welds
Symptom
Possible Cause(s)
Corrective Action
Bead is
intermittently too
thin or too thick
1. Inconsistent travel speed
2. Output amp setting incorrect
1. Carefully watch and control the width of the molten weld bead
2. Adjust output amp setting or change to smaller diameter electrode
Ragged depressions 1. Travel speed too fast
1. Watch orange molten weld puddle and control bead width
2. Practice running electrode across workpiece with welder OFF
3. Reduce output amp setting
at edge of weld
2. Arc length too short
3. Output amp setting too high
Weld bead does
not penetrate base
metal
1. Inconsistent travel speed
2. Output amp setting too low
3. Electrode diameter too large
1. Decrease and maintain constant travel speed
2. Increase output amp setting
3. Change to smaller diameter electrode
Electrode sticks to
workpiece
1. Arc length short
2. Amp setting low
3. Incorrect electrode
1. Lift electrode to correct arc length as soon as arc is struck
2. Increase amp setting or change to smaller diameter electrode
3. Verify electrode is suitable for 62.5 V open circuit voltage
Electrodes sputter
and stick
Damp electrodes
Use dry electrodes and store in dry location
14
Download from Www.Somanuals.com. All Manuals Search And Download.
GW4500
O r a n g e
l l e o Y w
B r o w n
R e d
G r e y
B l u e
W h i t e
B l a c k
i o V l e t
P o w e r S w i t c h
G e n e r a t o r / W
e l d e r
G r e e n
W h i t e
G r e e n
W h i t e
e l Y l o w
B l a c k
R e d
B r o w n
G r e y
B l u e
R e d
B r o w n
B a t t e r y C h a r g e r
1 2 V A C
B r o w n
B l u e
W h i t e
O r a n g e
R e d
Figure 11 - Wiring Diagram - AC Welder / Generator
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating Instructions and Parts Manual
Welder / Generator Assembly
1
17
18
19
20
16
22
21
11
10
3
6
5
7
4
2
15
14
11
11
12
11
13
9
8
Figure 12
16
Download from Www.Somanuals.com. All Manuals Search And Download.
GW4500
For replacement parts or technical assistance,
call 1-800-543-6400
Please provide following information:
- Model number
- Serial number (if any)
Address parts correspondence to:
Campbell Hausfeld
Attn: Parts Dept.
- Part description and number as shown in parts list
100 Production Drive
Harrison, OH 45030 USA
Replacement Parts List
Ref. No.
Description
Part Number
Qty.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
Engine - Honda GX270
Welded Frame Assembly
Tie Bracket
Isomount - Angle (short)
Isomount - Angle (extended)
Isomount
PM004264AV
GW004000AD
GN004399AD
GN004405AV
GN004406AV
GN004401AV
GW004050AD
▲
1
1
1
1
1
1
1
1
1
4
9
1
1
2
1
1
1
2
1
1
1
1
Hat Bracket
Hex head Screw - M8 - 1.25 x 60 mm
Flat Washer - 2 inch OD
Hex head Screw - 5/16 - 18 x 3/4 inch
Serrated Flange Nut - 5/16 - 18
Ground Wire
Hex head Screw - 5/16 - 18 x 1-1/4 inch
Flat Washer - 5/16 inch ID
Wing Nut - 5/16 - 18
Ground Clamp
Electrode Holder
Dinse Plug
Welding Cable - 6 AWG (14 foot)
Welding Cable - 6 AWG (6 foot)
Warning Decal
▲
▲
▲
GN003811AJ
▲
▲
▲
WC100100AV
WC200200AV
WC000200AV
▲
▲
DK689201AV
DK689202AV
CPSC Warning Decal
▲ Standard hardware item, available at local hardware stores
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating Instructions and Parts Manual
Alternator Assembly
17
22
18
13
2
14
6
11
21
20
12
4
19
23
7
28
10
24
15
16
9
25
27
4
28
3
1
5
26
8
10
Figure 13
18
Download from Www.Somanuals.com. All Manuals Search And Download.
GW4500
For replacement parts or technical assistance,
call 1-800-543-6400
Please provide following information:
- Model number
- Serial number (if any)
Address parts correspondence to:
Campbell Hausfeld
Attn: Parts Dept.
- Part description and number as shown in parts list
100 Production Drive
Harrison, OH 45030 USA
Replacement Parts List
Ref. No.
Description
Part Number
Qty.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
Alternator - 4kW, 140A AC (includes items 2 through 22)
Engine Adapter
Rotor Tie Rod
Nyloc Nut - M8-1.25
Diode, Suppressor, Capacitor Kit (2 each)
Air Outlet Guard
GW001000AV
GN002301SV
GN002304SV
▲
1
1
1
5
1
2
1
1
4
8
4
4
1
1
4
1
1
2
1
1
1
1
2
1
1
1
4
4
GN002337SJ
GN002310SV
GN002311SV
GN002312SV
GN002313SV
▲
Retaining Ring
Bearing
Stud - M8-1.25 x 30mm
Phillips Head Screw - M5-0.8 x 10mm
Phillips Head Screw - M6-1.0 x 10mm
Serrated Flange Nut - M6-1.0
Inductor
Capacitor - 35mF, 450V
Hex Head Screw - 3/8-16 x 1 inch
Alternator Fan
Top Cover
Dinse Socket - 200A
Commutator Knob - Small
Commutator - Output
Commutator Knob - Large
Commutator - Gen/Weld
Circuit Breaker - 25A, 250V
Endbell with Nutcover - GFCI, T-lock
Twistlock Receptacle - 125/250V, 20A
Duplex Receptacle - 120V, 20A
Nylock Nut - #8-32
▲
▲
GW001050SV
GW001016SV
▲
GW001020SV
GW001002SV
WC000300AV
WC400401AV
GW001045SV
GW001046SV
GW001047SV
GN003601AV
GN002480SJ
GN003501AV
GN003403AV
▲
Hex Head Screw - #8-32 x .75 inch
▲
▲ Standard hardware item, available at local hardware stores
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating Instructions and Parts Manual
Limited Warranty
1. DURATION: The manufacturer warrants that it will repair, at no charge for parts or labor, the welder, welding gun, or
cables, proven defective in material or workmanship, during the following time period(s) after date of original retail
purchase:
For 5 Years: The Welder Transformer and Rectifier
For 3 Years: The Entire Welder and Engine Driven Welder Generators (excluding clamps, welding gun, electrode holder,
cables, or accessories packed with the welder)
For 90 Days: The Welding Clamps, MIG Gun, Electrode Holder, Accessories, and Welding Cables (as applicable)
2. WHO GIVES THIS WARRANTY (WARRANTOR): Campbell Hausfeld / Scott Fetzer Company, 100 Production Drive, Harrison,
Ohio, 45030, Telephone: (800) 543-6400
3. WHO RECEIVES THIS WARRANTY (PURCHASER): The original purchaser (other than for purposes of resale) of the Campbell
Hausfeld Industrial product.
4. WHAT IS COVERED UNDER THIS WARRANTY: Substantial defects in material and workmanship which occur within the
duration of the warranty period. This warranty extends to the Welder, the Welders Transformer and Rectifier, Welding Gun
or Electrode holder, and cables only.
5. WHAT IS NOT COVERED UNDER THIS WARRANTY:
A. Implied warranties, including those of merchantability and FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED IN
DURATION TO THIS EXPRESS WARRANTY. After this period, all risks of loss, from whatever reason, shall be on the
purchaser. Some States do not allow limitation on how long an implied warranty lasts, so the above limitations may
not apply to you.
B. ANY INCIDENTAL, INDIRECT, OR CONSEQUENTIAL LOSS, DAMAGE, OR EXPENSE THAT MAY RESULT FROM ANY
DEFECT, FAILURE, OR MALFUNCTION OF THE CAMPBELL HAUSFELD INDUSTRIAL PRODUCT. Some States do not allow
limitations on how long an implied warranty lasts, so above limitations may not apply to you.
C. This warranty does not apply to any accessory items included with the product which are subject to wear from
usage; the repair or replacement of these items shall be at the expense of the owner. These MIG items include but
are not limited to; Contact Tips, Nozzles, Gun Liners, Drive Rollers, Felt Wire Cleaner. In addition, this warranty
does not extend to any damage caused by the untimely replacement or maintenance of any of the previously listed
CONSUMABLE parts.
D. Any failure that results from accident, purchaser’s abuse, neglect or failure to operate products in accordance with
instructions provided in the owner’s manual(s) supplied with product.
E. Pre-delivery service, i.e. assembly, oil or lubricants, and adjustment.
F. Gasoline engine components are expressly excluded from coverage under this limited warranty. Such components
should be returned by the purchaser to the original manufacturer or to its authorized repair stations for service.
6. RESPONSIBILITIES OF WARRANTOR UNDER THIS WARRANTY: Repair or replace, at Warrantor’s option, products or
components which have failed within duration of the warranty period.
7. RESPONSIBILITIES OF PURCHASER UNDER THIS WARRANTY:
A. Please call 800-543-6400 for warranty assistance.
B. Provide dated proof of purchase and maintenance records.
C. All welders must be delivered or shipped to the nearest Campbell Hausfeld Authorized Service Center. Freight costs,
if any, must be borne by the purchaser.
D. Use reasonable care in the operation and maintenance of the products as described in the owner’s manual(s).
8. WHEN WARRANTOR WILL PERFORM REPAIR OR REPLACEMENT UNDER THIS WARRANTY:
Repair or replacement will be scheduled and serviced according to the normal work flow at the servicing location, and
depending on the availability of replacement parts.
This Limited Warranty gives you specific legal rights and you may also have other rights which vary from state to state.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
|