CIGE9 Extractors
Manual for Installation, Use and Maintenance
Customer Care Department • The
Group Ltd. • Harby Road • Langar • Nottinghamshire • NG13 9HY
Download from Www.Somanuals.com. All Manuals Search And Download.
Using your Extractor
For best performance, you should switch on the extractor 15 minutes before starting to cook and leave it to run for
approximately 15 minutes after the end of cooking.
A - Light switch
B - Power indicator light
C - Power switch
A
B
C
A1 A2
C1 C3
C2 C4
Fig. 1
To switch the extractor light on or off
Slide the light switch to position A1 for off, or A2 for on.
•
To switch on the extractor, or change the motor speed
Slide the power switch to the position required dependent on the speed you require.
•
To switch the extractor off
Slide the power switch to position C1 for off.
•
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Care and Maintenance
IMPORTANT: DO NOT PERFORM MAINTENANCE
OR CLEANING OF THE EXTRACTOR WITHOUT FIRST
SWITCHING OFF THE ELECTRICITY SUPPLY.
Cleaning
You should use a non-abrasive cleaner. Any abrasive cleaner
(including Cif) will scratch the surface and could erase the
control panel markings.
You can clean you extractor effectively by simply using a
dilute solution of water and mild detergent and drying to a
shine with a clean cloth, for example the CDA E-Cloth.
Fig. 2
Cleaning the grease filter
The grease filters should be kept clean to minimise the risk
of fire.
At least once a month you should remove and clean the
grease filters with hot soapy water. You can also wash the
grease filters in a dishwasher, ensuring that you place it in an
upright position to prevent damage from other items in the
dishwasher. After rinsing and drying, replace the filters.
To remove the grease filters, pull open the handle on the
grease filter.. It will release at the handle side. Then lower the
grease filter to remove it completely. To replace the grease
filter, repeat the steps in reverse.
Please note:
Cleaning the grease filters in the dishwasher may lead to
discolouration. This is normal and does not constitute a fault
with the appliance.
Changing the charcoal filter (re-circulating only)
To ensure best performance of your extractor, you should
replace the charcoal filters every four to six months,
depending on use.
To attach a new charcoal filter, first remove the grease filters
as described above. Then offer up the charcoal filter to the
side of the motor as shown in figure 2 and turn it clockwise
until it locks into place. Repeat with the other charcoal filter
on the other side of the motor. Then replace the grease
filters and cover panels.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing the Light
IMPORTANT: DO NOT PERFORM MAINTENANCE OR CLEANING OF THE EXTRACTOR WITHOUT FIRST
SWITCHING OFF THE ELECTRICITY SUPPLY.
DO NOT CHANGE THE LIGHT BULB IMMEDIATELY AFTER USE AS THE BULB WILL BE HOT. ALLOW IT TO
COOL BEFORE REMOVING IT.
1. Remove the grease filters as described above.
2. Remove the faulty light bulb and replace with a light bulb no more powerful than that specified on the
rating plate.
3. Replace the grease filters.
Do not touch bulbs or adjacent areas during or straight after prolonged use of the lights.
The light is designed for use during cooking and not for general room illumination. Extended use of the light can
reduce the lifespan of the bulb.
Bulb replacement is not covered by the guarantee.
Only use bulbs recommended for your extractor. Do not fit bulbs of a higher power rating. Bulbs of a lower power
rating may be adequate for use, generally last longer, and use less energy.
Spare bulbs are available from CDA Customer Care or from your local DIY shop.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Mains Electricity Connection
THIS APPLIANCE MUST BE CONNECTED TO THE MAINS SUPPLY BY A COMPETENT PERSON, USING FIXED
WIRING VIA A DOUBLE POLE SWITCHED FUSED SPUR OUTLET AND PROTECTED BY A 3A FUSE.
We recommend that the appliance is connected by a qualified electrician, who is a member of the N.I.C.E.I.C. and who will
comply with the I.E.E. and local regulations.
DOUBLE POLE SWITCHED
The wires in the mains lead of this appliance are coloured in accordance with the
FUSED SPUR OUTLET
following code:
BLUE = NEUTRAL, BROWN = LIVE.
As the colours of the wires in the mains lead for the appliance may not correspond
with the coloured markings identifying the terminals connecting to the fused spur,
proceed as follows:
•
•
The wire which is coloured blue must be connected to the terminal marked N
(Neutral), or coloured black.
The wire which is coloured brown must be connected to the terminal marked
L (Live), or coloured red.
USE A 3 AMP FUSE
NOTE: USE A 3A FUSE
Assembly and electrical connection should be carried out by competent personnel.
When installing this product we recommend you seek the help of another individual.
IMPORTANT: THIS APPLIANCE IS A CLASS II APPLIANCE (DOUBLE INSULATED) AND IS NOT INTENDED TO
BE EARTHED. DO NOT FIT AN EARTH LEAD TO THIS EXTRACTOR.
Do not mount the isolation switch behind the chimney section. It is a requirement that you must be able to isolate the
extractor from the mains electrical supply after installation.
This appliance is intended to be connected to the mains electrical supply by means of an isolation switch and fused spur
and is intended to be protected by a 3A fuse. The use of a 13A fuse can cause damage to the internal wiring in the event
of a fault, and may also invalidate the warranty.
Electrical Information
Mains electrical voltage: 230 – 240Vac.
Total rated power consumption: 230W.
Troubleshooting
If your extractor is not working:
1. Check that the mains supply has not been switched off.
2. Check that the fuse in the spur has not blown.
Contact CDA Customer Care
A : Customer Care Department, The CDA Group Ltd, Harby Road, Langar, Nottinghamshire, NG13 9HY
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
IMPORTANT:
The extractor is intended to be mounted directly to
the ceiling using fixings appropriate for the ceiling.
Ensure that there is adequate ceiling strength and
supports at the fixing points; if in doubt, consult a
joiner or electrician.
540 – 820mm
Mounting Your Extractor:
When the extractor is to be installed above an electric hob,
the minimum distance between the hob and extractor must
exceed 600mm (650mm is recommended)
When the extractor is to be mounted above a gas hob, the
minimum distance between the hob and the extractor must
exceed 700mm (750mm is recommended)
Electric: 650mm recommended
Gas: 750mm recommended
If the instructions provided with your hob state that the
required distance between the hob and extractor must be
greater than 700mm, then that distance should be observed;
this is a legal requirement and may lead to your hob being
disconnected from the gas supply and the installation being
reported to RIDDOR (The height should be measured from
the top of the burners.
Fig. 3
IN THE ABSENCE OF ANY SUPPLIED INSTRUCTIONS
WITH YOUR GAS HOB, THE MINIMUM DISTANCE
BETWEEN THE HOB AND EXTRACTOR MUST BE AT
LEAST 760mm
The width of any hob must not be greater than the width of
the extractor installed above it.
Ducting and Ventilation
For best performance and lowest noise output, we
recommend the use of 120mm ducting. You can also use
100mm ducting but this will reduce performance.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
To fix your extractor to the ceiling, proceed as follows
1. Mark the fixing positions of the wall plugs that will be
used to secure your extractor to the ceiling, as shown in
fig. 4
191
2. Drill 4 holes and insert the wallplugs, ensuring that they
are suitable for use with your ceiling. If the extractor is to
be fixed directly to ceiling joists then wall plugs may not
be required.
203
Fig.4
3. Fit the vent adaptor (G) to the body of the extractor,
using the 2 self-tapping screws.
E
4. Calculate the height of the chimney section as follows
Length of support section = Ceiling height – (285 + H + Hob
height above floor)
D
B
H= 600 min for electric hobs (650mm recommended)
H=700mm minimum for gas hobs (750mm recommended)
5. Fix the 2 support sections(A) at the required length using
4 self-tapping screws. Note that if the exact height
cannot be set, use the frame position corresponding to
the next highest one.
6. Fix the support sections to the main motor body using 4
machine screws.
I
7. Slide the two decorative sections over the frame sections.
A
8. If your extractor is to be used as a recirculation device, fit
the deflector panel (I) onto the top of the frame section,
as shown.
G
9. With assistance, mount the entire assembly to the ceiling
using appropriate fixing screws. Once this operation
has been completed, the extractor is fully supported by
the ceiling fixings.
10. Mount the top chimney section (D) to the top of the
frame section using 2 screws (E)
11. If using the extractor to extract air outside, connect the
duct pipe to the vent adaptor (G), ensuring a good seal
to prevent air escaping. (The lower decorative section
(B) can be raised and tape to allow access to the outlet
adapter (G))
Fig.5
7
Download from Www.Somanuals.com. All Manuals Search And Download.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
To contact our Customer Care Department, or for Service,
please contact us on the details below.
Customer Care Department • The
Group Ltd. • Harby Road • Langar • Nottinghamshire • NG13 9HY
Download from Www.Somanuals.com. All Manuals Search And Download.
|