Operating & Maintenance
Instructions
Model Series
Covered in
This Manual
470000
540000
Model
Type
Code
Note: General Model Series numbers noted above are inclusive of the specific model
number found on your engine. To get replacement parts or technical assistance in
the future, write your engine Model, Type, Code and date of purchase here.
Month Day Year
WARNING
TABLE OF CONTENTS
Emission Information . . . . . . . . . . . . . . . . . . . . . . 2
Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5
Engine Information . . . . . . . . . . . . . . . . . . . . . . 5-7
Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Fuel and Coolant . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Starting and Stopping . . . . . . . . . . . . . . . . . . . . . 10
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . 11-14
Adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . 14-15
Parts and Service & Storage . . . . . . . . . . . . . . . 16
Warranty Information . . . . . . . . . . . . . . . . . . . . . 17
Briggs & Stratton does not approve or authorize the use of
these engines on 3-wheel All Terrain Vehicles (ATVs), motor
bikes, aircraft products or vehicles intended for use in
competitive events. Use of these engines in such applications
could result in property damage, serious injury (including
paralysis), or even death.
Need assistance? Go to www.briggsandstratton.com
for detailed information regarding
Briggs & Stratton engines.
Or call, 1-800-233-3723, (U.S.A. and Canada)
to hear a menu of pre-recorded messages
offering engine maintenance information.
PRINTED IN U.S.A.
Copyright 2003 by Briggs & Stratton Corporation
FORM NO. 275723-5/03
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE OPERATING ENGINE
• Read entire Operating & Maintenance Instructions AND the
instructions for the equipment this engine powers.*
• Failure to follow instructions could result in serious injury or
death.
THE OPERATING & MAINTENANCE INSTRUCTIONS
CONTAIN SAFETY INFORMATION TO
• Make you aware of hazards associated with engines
• Inform you of the risk of injury associated with those hazards, and
• Tell you how to avoid or reduce the risk of injury.
The safety alert symbol
information about hazards that can result in personal injury.
( )
is used to identify safety
HAZARD SYMBOLS AND MEANINGS
A signal word (DANGER, WARNING, or CAUTION) is used with
the alert symbol to indicate the likelihood and the potential severity
of injury. In addition, a hazard symbol may be used to represent
the type of hazard.
Fire
Explosion
Moving Parts
Shock
DANGER indicates a hazard which, if not
avoided, will result in death or serious injury.
Toxic Fumes
Hot Surface
WARNING indicates a hazard which, if not
avoided, could result in death or serious injury.
Kickback
Hot Liquid or Steam
CAUTION indicates a hazard which, if not
avoided, might result in minor or moderate
injury.
THE INTERNATIONAL SYMBOLS USED
ON THE ENGINE OR
CAUTION, when used without the alert symbol,
indicates a situation that could result in damage
to the engine.
IN THIS MANUAL INCLUDE:
WARNING
On Off
Read Owner’s Manual
Safety Alert
The engine exhaust from this
product contains chemicals known
to the State of California to cause
cancer, birth defects, or other
reproductive harm.
Oil
Choke
Stop Fuel Shutoff
Fuel
*
Briggs & Stratton does not necessarily know what equipment this engine will power. For that reason, you should carefully read
and understand the operating instructions for the equipment on which your engine is placed.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY
WARNING
WARNING
Gasoline and its vapors are extremely flam-
mable and explosive.
Starting engine creates sparking.
Sparking can ignite nearby flammable gases.
Explosion and fire could result.
Fire or explosion can cause severe burns or
death.
WHEN ADDING FUEL
• If there is natural or LP gas leakage in area, do not start
engine.
• Turn engine OFF and let engine cool at least 2 minutes
• Do not use pressurized starting fluids because vapors
before removing gas cap.
are flammable.
• Fill fuel tank outdoors or in well-ventilated area.
• Do not overfill fuel tank. Fill tank to approximately 1-1/2
inches below top of neck to allow for fuel expansion.
• Keep gasoline away from sparks, open flames, pilot
lights, heat, and other ignition sources.
• Check fuel lines, tank, cap, and fittings frequently for
cracks or leaks. Replace if necessary.
WARNING
WHEN STARTING ENGINE
Rapid retraction of starter cord (kickback) will pull
hand and arm toward engine faster than you can let
go.
• Make sure spark plug, muffler, fuel cap and air cleaner
are in place.
• Do not crank engine with spark plug removed.
• If fuel spills, wait until it evaporates before starting engine.
Broken bones, fractures, bruises or sprains could
result.
• If engine floods, set choke to OPEN/RUN position, place
throttle in FAST and crank until engine starts.
• When starting engine, pull cord slowly until resistance is
felt, then pull rapidly.
WHEN OPERATING EQUIPMENT
• Do not tip engine or equipment at angle which causes
gasoline to spill.
• Remove all external equipment/engine loads before
starting engine.
• Direct coupled equipment components such as, but not
limited to, blades, impellors, pulleys, sprockets, etc.,
must be securely attached.
• Do not choke carburetor to stop engine.
WHEN TRANSPORTING EQUIPMENT
• Transport with fuel tank EMPTY or with fuel shut-off valve
OFF.
WHEN STORING GASOLINE OR EQUIPMENT
WITH FUEL IN TANK
WARNING
• Store away from furnaces, stoves, water heaters or other
appliances that have pilot light or other ignition source
because they can ignite gasoline vapors.
Rotating parts can contact or entangle hands,
feet, hair, clothing, or accessories.
Traumatic amputation or severe laceration can
result.
• Operate equipment with guards in place.
• Keep hands and feet away from rotating parts.
• Tie up long hair and remove jewelry.
• Do not wear loose-fitting clothing, dangling drawstrings or
items that could become caught.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY
WARNING
WARNING
Running engines produce heat. Engine parts,
especially muffler, become extremely hot.
Engines give off carbon monoxide, an odorless,
colorless, poison gas.
Severe thermal burns can occur on contact.
Breathing carbon monoxide can cause nausea,
fainting or death.
Combustible debris, such as leaves, grass,
brush, etc. can catch fire.
• Start and run engine outdoors.
• Allow muffler, engine cylinder and fins to cool before
touching.
• Do not start or run engine in enclosed area, even if doors
or windows are open.
• Remove accumulated combustibles from muffler area
and cylinder area.
• Install and maintain in working order a spark arrester
before using equipment on forest-covered, grass-cov-
ered, brush-covered unimproved land. The state of
California requires this (Section 4442 of the California
Public Resources Code). Other states may have similar
laws. Federal laws apply on federal land.
WARNING
WARNING
Never remove radiator cap or radiator reservoir
cap while the engine is hot or running. Severe
thermal burns or injury can occur by escaping
steam or hot engine coolant.
Unintentional sparking can result in fire or
electric shock.
Unintentional start-up can result in entangle-
ment, traumatic amputation, or laceration.
Before Performing Adjustments or Repairs
• Disconnect spark plug wire and keep it away from spark
plug.
• Stop engine and allow to cool before removing radiator or
reservoir cap.
• To remove reservoir cap after engine is cool, place a thick
• Disconnect battery at negative terminal (only engines
cloth over cap and remove it slowly.
with electric start).
• To remove radiator cap after engine is cool, place a thick
cloth over cap and rotate it slowly counter-clockwise to
the first stop. Pressurized steam may emit from the cap,
stand back to avoid injury. Once all pressure is released,
rotate cap counter-clockwise while pushing down on cap
to remove.
When Testing For Spark
• Use approved spark plug tester.
• Do not check for spark with spark plug removed.
ENGINE INFORMATION
TECHNICAL INFORMATION
POWER RATINGS: The power ratings for an individual engine
model are initially developed by starting with SAE (Society of
Automotive Engineers) code J1940 (Small Engine Power &
Torque Rating Procedure) (Revision 2002-05). Given both the
wide array of products on which our engines are placed, and the
variety of environmental issues applicable to operating the
equipment, it may be that the engine you have purchased will not
develop the rated horsepower when used in a piece of power
equipment (actual “on-site” power). This difference is due to a
variety of factors including, but not limited to, the following:
differences in altitude, temperature, barometric pressure,
humidity, fuel, engine lubrication, maximum governed engine
speed, individual engine to engine variability, design of the
particular piece of power equipment, the manner in which the
engine is operated, engine run-in to reduce friction and clean out
of combustion chambers, adjustments to the valves and
carburetor, and other factors. The power ratings may also be
adjusted based on comparisons to other similar engines utilized
in similar applications, and will therefore not necessarily match the
values derived using the foregoing codes.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
ENGINE INFORMATION
MODEL SERIES 470000
11
13
12
1
2
10
16
15
16
3
3
4
14
9
20
5
8
17
6
7
1. Oil fill cap
12. Air Cleaner
18
2. Dipstick
13. Fuel pump (if equipped)
14. Muffler
15. Choke control
16. Throttle control
(2 possible locations)
17. Radiator reservoir
18. Oil filter
3. Spark plug (2 locations)
4. Starter solenoid
5. Starter
6. Oil drain plug (2 locations)
7. Fan belt
6
19
8. Fuel filter
9. Radiator drain plug
10. Radiator screen and handle
11. Radiator and radiator cap
19. Oil pressure sensor
20. Engine Model label
Model
Type
Code
xxxxxxxx
xxxxxx
xxxx xx
GENERAL INFORMATION
TUNE-UP SPECIFICATIONS
MODEL SERIES 470000
Armature air gap . . . . . . . . . 0.008 - 0.012 in. (0.20 - 0.30 mm)
Spark plug gap . . . . . . . . . . . . . . . . . . . . . . . . 0.020 in. (0.51 mm)
Valve clearance with valve springs installed and piston 1/4 in. (6 mm)
past top dead center (check when engine is cold).
This is a twin cylinder, overhead valve (OHV), liquid-cooled
engine. It is a low emissions engine.
In the state of California, Model Series 470000 engines are
certified by the California Air Resources Board to meet emissions
standards for 250 hours. Such certification does not grant the
purchaser, owner or operator of this engine any additional
warranties with respect to the performance or operational life of
this engine. This engine is warranted solely according to the
product and emissions warranties stated elsewhere in this
manual.
Intake . . . . . . . . . . . . . . . . . . . 0.007 - 0.009 in. (0.18 - 0.23 mm)
Exhaust . . . . . . . . . . . . . . . . . 0.007 - 0.009 in. (0.18 - 0.23 mm)
Bore . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.19 in. (81 mm)
Stroke . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.87 in. (73 mm)
Displacement . . . . . . . . . . . . . . . . . . . . . . . . . 45.9 cu. in. (752 cc)
Note: For practical operation, the horsepower loading should not
exceed 85% of rated horsepower. Engine power will decrease
3-1/2% for each 1,000 feet (300 meters) above sea level and 1%
for each 10° F (5.6° C) above 77° F (25° C). Engine will operate
satisfactorily at an angle up to 25°.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
ENGINE INFORMATION
MODEL SERIES 540000
12
12
1
19
11
10
13
2
3
14
4
18
3
9
15
5
6
16
17
8
7
7
1. Choke control
10. Carburetor
2. Breather/Breather tube
3. Spark plug (2 locations)
4. Engine Model label
11. Mechanical fuel pump
12. Air cleaner
13. Oil Fill
Model
Type
Code
xxxxxxxx
14. Dipstick
xxxxxx
xxxx xx
15. Regulator/Rectifier
16. Starter solenoid
17. Starter
18. Exhaust system/Muffler
19. Throttle control (2 locations)
5. Oil pressure sensor
6. Oil filter
7. Oil drain plug (2 locations)
8. Rotating screen
9. Carburetor cover (Removed)
GENERAL INFORMATION
TUNE-UP SPECIFICATIONS
MODEL SERIES 540000
Armature air gap . . . . . . . . . 0.005 - 0.008 in. (0.13 - 0.20 mm)
Spark plug gap . . . . . . . . . . . . . . . . . . . . . . . . 0.020 in. (0.51 mm)
Valve clearance with valve springs installed and piston 1/4 in. (6 mm)
past top dead center (check when engine is cold).
This is a twin cylinder, overhead valve (OHV), air-cooled engine.
It is a low emissions engine.
In the state of California, Model Series 540000 engines are
certified by the California Air Resources Board to meet emissions
standards for 1000 hours. Such certification does not grant the
purchaser, owner or operator of this engine any additional
warranties with respect to the performance or operational life of
this engine. This engine is warranted solely according to the
product and emissions warranties stated elsewhere in this
manual.
Intake . . . . . . . . . . . . . . . . . . . 0.004 - 0.006 in. (0.10 - 0.15 mm)
Exhaust . . . . . . . . . . . . . . . . . 0.004 - 0.006 in. (0.10 - 0.15 mm)
Bore . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85.5 mm (3.36 in.)
Stroke . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78 mm (3.07 in.)
Displacement . . . . . . . . . . . . . . . . . . . . . . . . 895 CC (54.6 cu. in.)
Note: For practical operation, the horsepower loading should not
exceed 85% of rated horsepower. Engine power will decrease
3-1/2% for each 1,000 feet (300 meters) above sea level and 1%
for each 10° F (5.6° C) above 77° F (25° C). Engine will operate
satisfactorily at an angle up to 25°.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
OIL
SAE Viscosity Grades
CAUTION: This engine is shipped from Briggs & Stratton
without oil. Check oil level before starting engine. If you start
the engine without oil, the engine will be damaged beyond
repair and will not be covered under warranty.
**
*
OIL CAPACITY
Model Series
Capacity
87 oz. (2.6 l)*
80 oz. (2.3 l)*
470000
540000
-20
-30
0
20
32 40
0
60
80
100
40
°F
°C
-20
-10
10
20
30
*Approximate amount when changing oil and filter.
STARTING TEMPERATURE RANGE ANTICIPATED BEFORE NEXT OIL CHANGE
TYPE OF OIL TO USE
• Use a high quality detergent oil classified “For Service SF, SG,
SH, SJ” or higher, such as Briggs & Stratton 30, Part Number
100005 (20 oz) or 100028 (48 oz).
• Do not use special additives.
• Do not mix gasoline with oil.
*
CAUTION: The use of non-synthetic multi-viscosity oils
(5W-30, 10W-30, etc.) in temperatures above 40° F (4° C)
will result in higher than normal oil consumption. When
using a multi-viscosity oil, check oil level more frequently.
** CAUTION:SAE 30 oil, if used below 40° F (4° C), will result
in hard starting and possible engine bore damage due to
inadequate lubrication.
• Choose a viscosity according to the table opposite.
Note: Synthetic oil meeting ILSAC GF-2, API
certification mark and API service symbol
(shown at left) with “SJ/CF ENERGY
CONSERVING” or higher, is an acceptable oil
at all temperatures. Use of synthetic oil does
not alter required oil change intervals.
CHECKING AND ADDING OIL
• Check oil level before starting the engine.
• Check level daily, or after every eight (8) hours.
• Keep oil level at FULL.
• Do not overfill.
Oil filling procedure:
First add 67 ounces (2 liters). Start and run engine at idle for 30
seconds. See Starting Instructions.
Shut engine off and wait 30 seconds.
OIL FILL
Then add more oil slowly to bring level to Full mark on dipstick.
Oil checking procedure:
[1] Place engine level.
Clean around oil fill and dipstick.
[2] Remove dipstick and wipe clean with cloth.
[3] Then push dipstick back in and remove to check oil level. Oil
should be at FULL line on dipstick.
[4] If oil is needed, add slowly.
[5] Fill to FULL line on dipstick - recheck.
[6] Replace dipstick firmly.
FULL
DIPSTICK
8
Download from Www.Somanuals.com. All Manuals Search And Download.
FUEL
TYPE OF FUEL TO USE
• Use clean, fresh, regular unleaded gasoline with a minimum of 85
octane. Fresh fuel prevents gum from forming in the fuel system
or on essential carburetor parts. Purchase fuel in quantity that
can be used within 30 days.
CAUTION: Some fuels, called oxygenated or reformulated
gasoline, are gasoline blended with alcohols or ethers.
Excessive amounts of these blends can damage the fuel
system or cause performance problems. If any undesirable
operating symptoms occur, use gasoline with a lower percent-
age of alcohol or ether.
• Do not use gasoline which contains Methanol.
• Do not mix oil with gasoline.
• For engine protection use Briggs & Stratton Gasoline Additive
available from your Authorized Briggs & Stratton Dealer (P/N
5041 or single use pouch).
• This engine is certified to operate on gasoline. Exhaust
Emission Control System: EM (Engine Modifications).
ADDING FUEL
WARNING
[1] Remove cap. Fill tank to approximately 1-1/2 inches below
top of neck to allow for fuel expansion. Be careful not to
overfill.
Briggs & Stratton Smart-Fill fuel can fills to the correct
level and automatically shuts off, reducing spills and
emissions.
• Turn engine OFF and let engine cool at least 2 minutes
before removing gas cap.
• Fill fuel tank outdoors or in well-ventilated area.
• Keep gasoline away from sparks, open flames, pilot lights,
[2] Replace cap before starting.
heat, and other ignition sources.
• If fuel spills, wait until it evaporates before starting engine.
COOLANT
MODEL 470000
• Do not touch radiator or open
radiator cap, or open reservoir
when engine is hot or running.
WARNING
• Allow engine to cool before
changing or adding coolant.
• This engine is liquid cooled.
• A 50/50% mixture is required of phosphate-free antifreeze and
tap water for heat dissipation, rust resistance and lubrication.
ADDING COOLANT
• Fill radiator to bottom of filler neck, and fill reservoir between
FULL and LOW.
COOLANT LEVEL
IN RESERVOIR
• Start and run engine for 30 seconds.
See Starting Instructions.
• Shut engine off and allow it to cool.
Recheck coolant levels in radiator and reservoir.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
STARTING & STOPPING
OIL PRESSURE SWITCH
CAUTION
BEFORE STARTING ENGINE FOR THE FIRST TIME:
• Fill and check oil level.
If engine is equipped with an oil pressure switch, the switch will
either activate a warning device or stop the engine when the
engine runs low on oil. (Read the operating instructions supplied
by the equipment manufacturer to determine if and how your
engine is equipped.)
• Fill with fresh gasoline.
See OIL PRESSURE on page 12 for oil filling instructions.
• Fill and check coolant level.
• Charge battery as the equipment manufacturer
TEMPERATURE LIGHT (If equipped)
MODEL 470000 ONLY
recommends.
If temperature light comes on, engine is overheating.
• The manufacturer of equipment
WARNING
on which this engine is installed
specifies top speed at which
engine will be operated. DO NOT
EXCEED this speed.
CAUTION:
DO NOT OPERATE If the temperature light is on. Check
coolant levels, fan belt, and any restriction to air flow. If light
persists, see an Authorized Service Dealer.
STARTING IN COLD WEATHER:
♦ Use correct type of oil for expected starting temperature. See
♦ Open fuel shut-off valve, if equipped, before starting engine.
Oil.
♦ Allow engine to warm up several seconds to several
minutes, depending on outside temperature.
♦ Use fresh gasoline, which has higher volatility to improve
♦ Gradually open choke.
starting.
♦ For maximum performance and life, operate engine with
♦ Remove external equipment/engine loads.
choke in OPEN and throttle in FAST.
(See equipment operating instructions.)
TO START ENGINE
[1] Check oil level (see p. 8).
Typical Controls
[2] Open fuel shut-off valve (if equipped).
[3] Move choke control to CHOKE or START.
[4] Move throttle (if equipped) to FAST.
[5] Push rocker switch (if equipped)
to ON or RUN.
[6] Insert key and turn to START.
CAUTION: To prolong starter life, use short starting
cycles (5 seconds maximum, then wait one minute).
Follow equipment manufacturer’s recommendations
for charging battery.
Fuel Shut-off
Choke
Throttle
[7] Let engine warm up.
If choke equipped: Slowly adjust toward RUN position.
Wait until engine runs smoothly before each choke
adjustment.
TO STOP ENGINE
[1] Move throttle to SLOW (if equipped).
STOP
Stop Switch
RUN
[2] Turn key to OFF. Remove key and store out of reach of children.
[3] Push rocker switch (if equipped) to OFF or STOP.
[4] Close fuel shut-off valve (if equipped).
Key
10
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
MAINTENANCE
Regular maintenance will improve the performance and extend the life of the engine. See any Authorized Briggs & Stratton Dealer for
service. Use only genuine Briggs & Stratton parts. Other parts may not perform as well, may damage the engine, and may result in
injury. In addition, use of other parts may void your warranty.
ENGINE AND ENGINE PARTS
We recommend that you see an authorized Briggs & Stratton Service Dealer for all maintenance and service of the engine and engine
parts. Use only genuine Briggs & Stratton parts.
Perform the following at recommended intervals:
Task
Perform task at hourly
or calendar interval,
whichever comes first.
EMISSION CONTROL
Maintenance, replacement or repair of the emission control
devices and systems may be performed by any nonroad
engine repair establishment or individual. However, to obtain
no charge repairs under the terms and provisions of the Briggs &
Stratton warranty statement, any service or emission control part
repair or replacement must be performed by a factory authorized
dealer.
Check oil level
4
Check for
4
oil leaks
WARNING
Change oil
4*
4*
If you perform any maintenance on the engine, first
disconnect the spark plug wires from the spark
plugs, and disconnect the battery at the negative
terminal (electric starter engines only) to prevent
unintentional sparking. Unintentional sparking can
result in fire or electric shock. Unintentional start-up
can result in entanglement, traumatic amputation or
laceration. Use only correct tools.
Change oil filter
Clean
air cleaner
4
*
*
Replace air cleaner
cartridge
4
*
*
Check valve
clearance
4
*
4
4
Check battery
electrolyte
Change
spark plugs
WARNING
• Do not strike the flywheel with a hammer or hard object
because the flywheel may later shatter during operation.
4
Change fuel filter
4
Clean spark
arrestor (if equipped)
• Do not tamper with governor spring, links or other parts to
4
increase engine speed.
MODEL 540000 ONLY
Replace Safety
filter cartridge
SPARK PLUG
Change spark plugs yearly. Use only Briggs & Stratton Spark
Tester (part number 19368) to check for spark.
4
MODEL 470000 ONLY
Check coolant
4
Note: In some areas, local law
requires using resistor spark plug
to suppress ignition signals. If this
engine was originally equipped
with resistor spark plugs, use
same type for replacement.
.020” (0.51 mm)
WIRE GAGE
Change coolant
Check fan belt
4
*
*
*
4
*
Change oil and filter after first 50 hours of use, then every
100 hours or every season. Change oil every 50 hours when
operating the engine under heavy load or in high
temperatures.
Check valve clearance after first 50 hours of use, then
every 250 hours.
** Clean more often under dusty conditions or when airborne
debris is present. Replace air cleaner parts, if very dirty.
VALVE CLEARANCE
*** If an extended life coolant is used, interval may be increased
to once every 3000 hours.
Check valve clearance every 250 hours.
(See Tune-up Specifications on page 6).
11
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
CHANGING OIL AND OIL FILTER
Change oil and filter after first 50 hours and every 100 hours thereafter.
[1] With engine OFF but still warm, remove oil drain plug and drain oil into
appropriate receptacle. Reinstall drain plug
OIL FILTER
[2] Remove oil filter. Before installing new filter, lightly oil filter gasket with
fresh, clean oil.
[3] Screw filter on by hand until gasket contacts oil filter adapter. Tighten
1/2 to 3/4 turn more.
[4] Place engine level. Remove oil fill cap and add fresh oil.
Oil filling procedure: First, add 67 ounces (2 liters). Start and run
engine at idle for 30 seconds. Shut engine off and wait 30 seconds.
Then, add more oil slowly to bring level to Full mark on dipstick. Do
not overfill.
OIL DRAIN PLUG
OIL FILL
[5] Replace oil fill cap and dipstick
CAUTION: Used oil is a hazardous waste product. Dispose of used oil
properly. Do not discard with household waste. Check with your local
authorities, service center, or dealer for safe disposal/recycling facilities.
OIL PRESSURE
If oil pressure drops below 1-4 psi (.1-.2 kg/cm ), an oil pressure switch (if
2
engine is equipped) will either activate a warning device or stop the engine.
Check oil level with dipstick. If oil level is between ADD and FULL mark on
dipstick, Do not try to restart engine. Contact an Authorized Briggs & Stratton
Service Dealer. Do not operate engine until oil pressure is corrected.
FULL
DIPSTICK
If oil level is below ADD mark on dipstick, add oil to bring level to FULL mark.
Restart engine and check oil pressure. If pressure is normal, continue to
operate engine.
Note: Oil pressure gauge, if engine is equipped, is supplied by manufactur-
er of equipment.
AIR CLEANER
CLAMPS
CAUTION: Do not use pressurized air or solvents to
clean cartridge. Pressurized air can damage cartridge;
solvents will dissolve cartridge.
AIR
CLEANER
BODY
COVER
Clean cartridge every 100 hours. To clean cartridge, gently tap on
end with handle of screwdriver. Replace cartridge every 600
hours. Clean and replace more often under dusty conditions.
AIR FILTER
CARTRIDGE
Model 5400 Safety Filter Installation
[1] Unlock clamps and remove cover.
SAFETY FILTER
AIR FILTER
[2] Remove cartridge from air cleaner body, and inspect.
Replace if very dirty or any damage occurs to cartridge.
CARTRIDGE
CARTRIDGE
[3] Carefully clean out air cleaner cover.
[4] Install cartridge in body.
[5] Install cover and lock clamps with rubber valve down.
AIR
CLEANER
BODY
AIR
CLEANER
BODY
Model 5400 Safety Filter Installation
Replace cartridge every 600 hours, or with every other air filter
cartridge replacement. To replace cartridge, pull carefully to
remove from air cleaner body, ensure no debris enters engine.
Install new safety cartridge first, then install air filter cartridge over
safety filter.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
CHANGING COOLANT (MODEL 470000)
Coolant should be replaced every year, unless an approved
extended life coolant is used. Then replace every 3000 hours.
WARNING
• A 50/50% mixture is required of phosphate-free antifreeze and
Never remove radiator cap or radiator reservoir
cap while the engine is hot or running. Severe
thermal burns or injury can occur by escaping
steam or hot engine coolant.
tap water for heat dissipation, rust resistance and lubrication.
[1] Remove drain plug. As coolant is running out, open radiator
cap to allow any trapped coolant to drain. Replace drain
plug.
• Stop engine and allow to cool before removing radiator or
reservoir cap.
[2] Remove reservoir bottle, drain it and reinstall.
• To remove reservoir cap after engine is cool, place a thick
cloth over cap and remove it slowly.
[3] Fill radiator to bottom of filler neck and reservoir between
FULL and LOW. Replace radiator cap.
• To remove radiator cap after engine is cool, place a thick
cloth over cap and rotate it slowly counter-clockwise to
the first stop. Pressurized steam may emit from the cap,
stand back to avoid injury. Once all pressure is released,
rotate cap counter-clockwise while pushing down on cap
to remove.
[4] Start and run engine for 30 seconds.
[5] Shut engine off and allow it to cool. Recheck coolant levels in
radiator and reservoir.
CAUTION: Used coolant is a hazardous waste product.
Dispose of used coolant properly. Check with your local
authorities, service center, or dealer for safe disposal/re-
cycling facilities.
[6] Coolant level in reservoir should be between FULL and LOW
when engine is cold.
Normal coolant temperature
gauge (if equipped) should
read between 175° and 195° F
(80° and 90° C) when engine is
running.
WARNING
If coolant temperature rises above 220° F (105° C), the
temperature light (if equipped) will illuminate. Idle engine down
for a while. Then stop engine. Once engine is cooled, check
coolant level, fan belt tension and clean any clogged radiator
fins.
COOLANT LEVEL
IN RESERVOIR
RADIATOR
DRAIN PLUG
Side view
Front view
FAN BELT (MODEL 470000)
♦ Check condition of fan belt.
♦ Replace if damaged or worn.
FAN BELT
BOLT “A”
To adjust fan belt tension
[1] First, loosen bolt A and bolt B.
TORQUE
WRENCH
TORQUE
WRENCH
SQUARE
TORQUE
HOLE
[2] Fit torque wrench in the square
torque hole located on the bracket.
SQUARE
TORQUE HOLE
BOLT “B”
[3] Apply 115 in-lbs of torque in the
direction of the arrow.
FAN
BELT
[4] While belt is being tensioned per
step [3], torque bolt A and B to 135
in-lbs.
BOLT “B”
13
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
CLEANING DEBRIS
Daily or before every use, clean accumulated debris from engine.
Keep linkage, springs and controls clean. Keep area around and
behind muffler free of any combustible debris.
Model 470000: Use the handle on the radiator screen to lift off for
cleaning. Clean screen thoroughly and clean radiator fins.
CLEAN DEBRIS
RADIATOR
SCREEN
HANDLE
CLEAN DEBRIS
Model 540000: Remove front carburetor cover, and clean around
intake manifold and carburetor.
CLEAN DEBRIS
CAUTION: Do not use water to clean engine parts. Water could
contaminate fuel system. Low pressure compressed air may be
used, be careful not to damage radiator fins.
Engine parts should be kept
clean to reduce the risk of over-
heating and ignition of accumu-
lated debris.
WARNING
FUEL FILTER
MUFFLER/FUEL SYSTEM
Drain fuel tank or close fuel shut-off
valve before replacing fuel filter.
Otherwise, fuel can leak out,
creating a fire/explosion hazard.
Replacement parts for the muffler
WARNING must be the same and installed in
the same position as the original
WARNING
parts, otherwise fire can occur.
When replacing fuel filter, ensure
clamps are tight and fuel flows into
the same direction as the arrow
marked FLOW.
Replacement parts for fuel system
(cap, hoses, tanks, filters, etc.) must be the same as original
parts, otherwise fire can occur.
PART NO. 807241
ADJUSTMENTS
CARBURETOR ADJUSTMENT
Differences in fuel, temperature, altitude or load may require minor
carburetor adjustment. Air cleaner and air cleaner cover must be
assembled to carburetor before starting engine.
The manufacturer of the equipment
on which this engine is installed
specifies top speed at which the
WARNING
engine will be operated. DO NOT EXCEED this speed.
The carburetor on this engine is low emission. The carburetor is
equipped with an idle speed adjustment screw. The Model
470000 is equipped with an idle mixture valve with a limiter (see
inset), which allows some adjustment. DO NOT remove limiter
caps. DO NOT force beyond limit.
Engine will be running to perform
WARNING
this adjustment. Keep away from all
rotating and moving parts.
TO ADJUST CARBURETOR
[1] Start engine and warm up approximately 5 minutes before
adjusting.
[2] Place throttle control in SLOW position.
[3] Rotate carburetor throttle lever against the idle speed screw
and hold it.
Note: Engines operated at about 3000 feet (900 meters) or higher above
sea level may require a high altitude carburetor main jet. If erratic perfor-
mance is observed, contact a Briggs & Stratton Authorized Service
Dealer for cost to install/purchase a high altitude carburetor main jet.
[4] Turn idle speed screw to obtain 1500 rpm
LIMITER
CARBURETOR
CAP
[5] Model 470000 Only: While still holding carburetor throttle
lever against idle speed screw, set cylinder #1 idle mixture
valve to obtain highest speed. Then set cylinder #2 idle
mixture valve to obtain highest speed. Do not force beyond
limit. Do not remove limiter caps.
[6] Model 470000 Only: Release carburetor throttle lever.
Move throttle control to FAST position. Engine should
accelerate smoothly. If it does not, readjust idle mixture
valves slightly counterclockwise.
THROTTLE
LEVER
IDLE MIXTURE
IDLE SPEED
SCREW
VALVES
CYL # 1
CYL # 2
Only Model 470000 carburetor has idle mixture valves
14
Download from Www.Somanuals.com. All Manuals Search And Download.
ADJUSTMENTS
Disconnect spark plug and battery before performing adjustments.
WARNING
REMOTE CONTROL ADJUSTMENTS
MODEL 4700000
THROTTLE STOP
THROTTLE LEVER
ALTERNATE REMOTE THROTTLE
WIRE AND CASING
THROTTLE WIRE AND CASING
ALTERNATE REMOTE THROTTLE
CASING CLAMP SCREW
THROTTLE CASING CLAMP SCREW
CHOKE
LEVER
REMOTE CHOKE CASING
CLAMP SCREW
Throttle control adjustment
Choke control adjustment
[1] Move choke control to CHOKE position. (Carburetor
choke should be completely closed.)
[1] Move throttle control to FAST. (Swivel should be against
throttle stop.)
[2] If not, loosen casing clamp screw.
[2] If not, loosen casing clamp screw. Move casing and wire
until swivel is against throttle stop, see direction shown by
arrow.
[3] Then move casing, wire and engine choke lever in
direction shown until choke is completely closed.
[4] Tighten casing clamp screw.
[3] Tighten casing clamp screw.
REMOTE CONTROL ADJUSTMENTS
MODEL 540000
THROTTLE WIRE AND CASING
CHOKE
LEVER
VARIABLE FRICTION
SETTING NUT
THROTTLE
CASING CLAMP
SCREW
THROTTLE
SWIVEL
THROTTLE STOP
REMOTE CHOKE CASING
CLAMP SCREW
THROTTLE LEVER
ALTERNATE REMOTE
THROTTLE CASING
CLAMP SCREW
ALTERNATE REMOTE THROTTLE
WIRE AND CASING
Throttle control adjustment
Choke control adjustment
[1] Move throttle control to FAST. (Swivel should be against
throttle stop.)
[1] Move choke control to CHOKE position. (Carburetor
choke should be completely closed.)
[2] If not, loosen casing clamp screw. Move casing and wire
until swivel is against throttle stop, see direction shown by
arrow.
[2] If not, loosen casing clamp screw.
[3] Then move casing, wire and engine choke lever in
direction shown until choke is completely closed.
[4] Tighten casing clamp screw.
[3] Tighten casing clamp screw.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
STORAGE
Then, engine and fuel can be stored up to 24 months.
[2] While engine is still warm, change oil.
STORAGE
Engines stored over 30 days need special attention.
[3] Remove spark plugs and pour about 1 oz. (30 ml) of engine
oil into each cylinder. Replace spark plugs and crank slowly
to distribute oil.
[1] To prevent gum from forming in fuel system or on essential
carburetor parts:
a) if fuel tank contains oxygenated or reformulated gasoline
(gasoline blended with an alcohol or an ether), run engine
until it stops from lack of fuel, or b) if fuel tank contains
gasoline, either run engine until it stops from lack of fuel, or add
a gasoline additive to the gas in the tank. (See parts list.
Single-use pouches of gas additive are available from your
service dealer.) If you use a gas additive, run the engine for
several minutes to circulate the additive through the carburetor.
[4] Clean engine of surface debris, chaff or grass.
[5]
Store in a clean, dry area. Do not
store in same area as a stove,
furnace, water heater, or other
appliance that uses a pilot light or
has a device that can create a
spark.
WARNING
SERVICE
See an Authorized Briggs & Stratton Service Dealer. Each one
carries a stock of Genuine Briggs & Stratton Parts and is equipped
with special service tools. Trained mechanics assure expert repair
service on all Briggs & Stratton engines. Only dealers advertising
as “Authorized Briggs & Stratton” are required to meet Briggs &
Stratton standards.
PARTIAL LIST OF
GENUINE BRIGGS & STRATTON PARTS
PART PART NO.
Air cleaner cartridge (Model 470000) . . . . . . . . . . . . . . . 820263
Air cleaner cartridge (Model 540000) . . . . . . . . . . . . . . . 809670
Safety air cleaner cartridge (Model 540000) . . . . . . . . . . 821136
Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100028
Oil filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 492932
Fuel filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 691035
Fuel pump (Model 470000) . . . . . . . . . . . . . . . . . . . . . . . 807242
Fuel pump (Model 540000) . . . . . . . . . . . . . . . . . . . . . . . 809669
Fan belt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 807243
Gas additive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5041
Resistor spark plug . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 491055
Spark plug wrench . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19374
When you purchase equipment powered by a Briggs
& Stratton engine, you are assured of highly skilled,
reliable service at more than 30,000 Authorized
Service Dealers worldwide, including more than
5,000 Master Service Technicians. Look for these
signs wherever Briggs & Stratton service is offered.
You may locate your nearest Authorized Briggs & Stratton Service
Dealer in our dealer locator map on our web site
Spark tester . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19368
Oil pump kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5056
(uses standard electric drill to remove oil from engine quickly)
directory under “Engines, Gasoline” or “Gasoline En-
gines,” or “Lawn Mowers” or similar category.
Repair Manual (Model 470000) . . . . . . . . . . . . . . . . . . . . 275429
An illustrated shop manual includes common
specifications and detailed information cover-
ing adjustment, tune-up and repair of Briggs &
Stratton OHV, twin cylinder, 4 cycle engines. It
is available for purchase from an Authorized
Briggs & Stratton Service Dealer or you can
order it from the factory. Write: Briggs & Stratton
Corporation, Attn: Service Division
P. O. Box 1144, Milwaukee, WI 53201
16
Download from Www.Somanuals.com. All Manuals Search And Download.
BRIGGS & STRATTON ENGINE OWNER WARRANTY POLICY
Effective January 1, 2003 replaces all undated Warranties and all Warranties dated before January 1, 2003
LIMITED WARRANTY
Briggs & Stratton Corporation will repair or replace, free of charge, any part(s) of the engine that is defective in material or workmanship or both.
Transportation charges on parts submitted for repair or replacement under this warranty must be borne by purchaser. This warranty is effective for the
time periods and subject to the conditions stated below. For warranty service, find the nearest Authorized Service Dealer in our dealer locator map
THERE IS NO OTHER EXPRESS WARRANTY. IMPLIED WARRANTIES, INCLUDING THOSE OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR FROM PURCHASE, OR TO THE EXTENT PERMITTED BY LAW ANY AND ALL IMPLIED
WARRANTIES ARE EXCLUDED. LIABILITY FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES ARE EXCLUDED TO THE EXTENT
EXCLUSION IS PERMITTED BY LAW. Some states or countries do not allow limitations on how long an implied warranty lasts, and some states or
countries do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation and exclusion may not apply to you.
This warranty gives you specific legal rights and you may also have other rights which vary from state to state and country to country.
OUR PRODUCT
Vanguard
E
Classic
E
Fource
E
ELSE
EtekE
Intek
(Kool Bore)
Power BuiltE OHV
E
I/Cr
Industrial Plus
E
Intek
E
Quantumr
(Sleeve Bore)
Quattro
E
Q45E
Sprint
E
WARRANTY PERIOD*
Consumer Use
2 years
1 year
2 years
90 days
1 year
2 years
1 year
Commercial Use
90 days
*
Note the following special warranty periods: 2 years for Classic engines in the European Union and Eastern European countries, for all consumer products in
the European Union, and for emission control systems on engines certified by EPA and CARB. 5 years for consumer use, 90 days for commercial use of Touch-N-
Mow starter on Quantum and Intek engines. Engines used in competitive racing or on commercial or rental tracks are not warrantied.
The warranty period begins on the date of purchase by the first retail consumer or commercial end user, and continues for the period of time stated in the table
above. “Consumer use” means personal residential household use by a retail consumer. “Commercial use” means all other uses, including use for commercial,
income producing or rental purposes. Once an engine has experienced commercial use, it shall thereafter be considered as a commercial use engine for pur-
poses of this warranty.
NO WARRANTY REGISTRATION IS NECESSARY TO OBTAIN WARRANTY ON BRIGGS & STRATTON PRODUCTS. SAVE YOUR PROOF OF PURCHASE
RECEIPT. IF YOU DO NOT PROVIDE PROOF OF THE INITIAL PURCHASE DATE AT THE TIME WARRANTY SERVICE IS REQUESTED, THE
MANUFACTURING DATE OF THE PRODUCT WILL BE USED TO DETERMINE THE WARRANTY PERIOD.
ABOUT YOUR ENGINE WARRANTY
Briggs & Stratton welcomes warranty repair and apologizes to
you for being inconvenienced. Any Authorized Service Dealer
may perform warranty repairs. Most warranty repairs are
handled routinely, but sometimes requests for warranty
service may not be appropriate. For example, warranty would
not apply if engine damage occurred because of misuse, lack
of routine maintenance, shipping, handling, warehousing or
improper installation. Similarly, warranty is void if the serial
number of the engine has been removed or the engine has
been altered or modified.
If a customer differs with the decision of the Service Dealer, an
investigation will be made to determine whether the warranty
applies. Ask the Service Dealer to submit all supporting facts to
his Distributor or the Factory for review. If the Distributor or the
Factory decides that the claim is justified, the customer will be
fully reimbursed for those items that are defective. To avoid
misunderstanding which might occur between the customer
and the Dealer, listed below are some of the causes of engine
failure that the warranty does not cover.
the engine because of improper maintenance, is not covered
by warranty.
intervals, clean and re−oil the Oil−Foamelement or the
foam pre−cleaner, and replace the cartridge.) Read
Operating & Maintenance Instructions.
This warranty covers engine related defective material
and/or workmanship only, and not replacement or refund
of the equipment to which the engine may be mounted.
Nor does the warranty extend to repairs required because
of:
1. PROBLEMS CAUSED BY PARTS THAT ARE NOT
ORIGINAL BRIGGS & STRATTON PARTS.
2. Equipment controls or installations that prevent starting,
cause unsatisfactory engine performance, or shorten
engine life. (Contact equipment manufacturer.)
3. Leaking carburetors, clogged fuel pipes, sticking valves,
or other damage, caused by using contaminated or stale
fuel. (Use clean, fresh, lead−free gasoline and Briggs &
Stratton Fuel Stabilizer, Part No. 5041.)
4. Parts which are scored or broken because an engine
was operated with insufficient or contaminated
lubricating oil, or an incorrect grade of lubricating oil
(check oil level daily or after every 8 hours of operation.
Refill when necessary and change at recommended
intervals.) OIL GARD may not shut down running
engine. Engine damage may occur if oil level is not
properly maintained. Read Operating & Maintenance
Instructions.
5. Repair or adjustment of associated parts or assemblies
such as clutches, transmissions, remote controls, etc.,
which are not manufactured by Briggs & Stratton.
6. Damage or wear to parts caused by dirt, which entered
the engine because of improper air cleaner
maintenance, re−assembly, or use of a non−original air
cleaner element or cartridge. (At recommended
7. Parts damaged by over−speeding, or overheating
caused by grass, debris, or dirt, which plugs or clogs the
cooling fins, or flywheel area, or damage caused by
operating the engine in a confined area without sufficient
ventilation. (Clean fins on the cylinder, cylinder head and
flywheel at recommended intervals.) Read Operating &
Maintenance Instructions.
8. Engine or equipment parts broken by excessive
vibration caused by a loose engine mounting, loose
cutter blades, unbalanced blades or loose or
unbalanced impellers, improper attachment of
equipment to engine crankshaft, over−speeding or other
abuse in operation.
9. A bent or broken crankshaft, caused by striking a solid
object with the cutter blade of a rotary lawn mower, or
excessive v−belt tightness.
10. Routine tune−up or adjustment of the engine.
11. Engine or engine component failure, i.e., combustion
chamber, valves, valve seats, valve guides, or burned
starter motor windings, caused by the use of alternate
fuels such as, liquified petroleum, natural gas, altered
gasolines, etc.
Normal wear:
Engines, like all mechanical devices, need periodic parts
service and replacement to perform well. Warranty will not
cover repair when normal use has exhausted the life of a part or
an engine.
Improper maintenance:
The life of an engine depends upon the conditions under which
it operates, and the care it receives. Some applications, such
as tillers, pumps and rotary mowers, are very often used in
dusty or dirty conditions, which can cause what appears to be
premature wear. Such wear, when caused by dirt, dust, spark
plug cleaning grit, or other abrasive material that has entered
Warranty is available only through service dealers which
have been authorized by Briggs & Stratton Corporation.
your nearest Authorized Service Dealer is listed in the
ꢀYellow Pages" of your telephone directory under
ꢀEngines, Gasoline" or ꢀGasoline Engines," ꢀLawn
Mowers," or similar category.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Briggs & Stratton Corporation (B&S), the California Air Resources Board (CARB)
and the United States Environmental Protection Agency (U.S. EPA)
Emission Control System Warranty Statement (Owner’s Defect Warranty Rights and Obligations)
EMISSION CONTROL WARRANTY COVERAGE IS APPLICABLE TO CERTIFIED ENGINES PURCHASED IN CALIFORNIA IN 1995 AND THERE-
AFTER, WHICH ARE USED IN CALIFORNIA, AND TO CERTIFIED MODEL YEAR 1997 AND LATER ENGINES WHICH ARE PURCHASED AND
USED ELSEWHERE IN THE UNITED STATES (AND AFTER JANUARY 1, 2001 IN CANADA).
California and United States Emission Control Defects Warranty Statement
The California Air Resources Board (CARB), U.S. Elsewhere in the United States, new non-road, Your emission control system includes parts
EPA and B&S are pleased to explain the Emission spark-ignition engines certified for model year such as the carburetor, air cleaner, ignition sys-
Control System Warranty on your model year 1997 and later must meet similar standards set tem, muffler and catalytic converter. Also in-
2002 and later small off-road engine (SORE). In forth by the U.S. EPA. B&S must warrant the emis- cluded may be connectors and other emission
California, new small off-road engines must be de- sion control system on your engine for the periods related assemblies.
signed, built and equipped to meet the State’s of time listed below, provided there has been no
Where a warrantable condition exists, B&S will
repair your small off-road engine at no cost to
you including diagnosis, parts and labor.
stringent anti-smog standards.
abuse, neglect or improper maintenance of your
small off-road engine.
Briggs & Stratton Emission Control Defects Warranty Coverage
Small off-road engines are warranted relative to emission control parts defects for a period of two years, subject to provisions set forth below. If any
covered part on your engine is defective, the part will be repaired or replaced by B&S.
Owner’s Warranty Responsibilities
As the small off-road engine owner, you are re- As the small off-road engine owner, you should The undisputed warranty repairs should be
sponsible for the performance of the required however be aware that B&S may deny you war- completed in a reasonable amount of time, not
maintenance listed in your Operating and Main- ranty coverage if your small off-road engine or a to exceed 30 days.
tenance Instructions. B&S recommends that part has failed due to abuse, neglect, improper
you retain all your receipts covering mainte- maintenance or unapproved modifications.
If you have any questions regarding your war-
ranty rights and responsibilities, you should con-
nance on your small off-road engine, but B&S
You are responsible for presenting your small
tact
a
B&S Service Representative at
cannot deny warranty solely for the lack of re-
off-road engine to an Authorized B&S Service
1-414-259-5262.
ceipts or for your failure to ensure the perfor-
mance of all scheduled maintenance.
Dealer as soon as a problem exists.
The emission warranty is a defects warranty.
Defects are judged on normal engine perfor-
mance. The warranty is not related to an in-use
emission test.
Briggs & Stratton Emission Control Defects Warranty Provisions
The following are specific provisions relative to your Emission Control Defects Warranty Coverage. It is in addition to the B&S engine warranty for non-
regulated engines found in the Operating and Maintenance Instructions.
1. Warranted Parts
2. Length of Coverage
set forth in the B&S Engine Warranty Policy.
B&S is not liable to cover failures of War-
ranted Parts caused by the use of add-on,
non-original, or modified parts.
B&S warrants to the initial owner and each
subsequent purchaser that the Warranted
Parts shall be free from defects in materials
and workmanship which caused the failure
of the Warranted Parts for a period of two
years from the date the engine is delivered to
a retail purchaser.
Coverage under this warranty extends only
to the parts listed below (the emission con-
trol systems parts) to the extent these parts
were present on the engine purchased.
5. Maintenance
a. Fuel Metering System
Any Warranted Part which is not scheduled
for replacement as required maintenance or
which is scheduled only for regular inspec-
tion to the effect of “repair or replace as nec-
essary” shall be warranted as to defects for
the warranty period. Any Warranted Part
which is scheduled for replacement as re-
quired maintenance shall be warranted as to
defects only for the period of time up to the
first scheduled replacement for that part. Any
replacement part that is equivalent in perfor-
mance and durability may be used in the per-
formance of any maintenance or repairs.
The owner is responsible for the perfor-
mance of all required maintenance, as de-
fined in the B&S Operating and Maintenance
Instructions.
•
•
•
Cold start enrichment system
Carburetor and internal parts
Fuel Pump
3. No Charge
Repair or replacement of any Warranted
Part will be performed at no charge to the
owner, including diagnostic labor which
leads to the determination that a Warranted
Part is defective, if the diagnostic work is
performed at an Authorized B&S Service
Dealer. For emissions warranty service
contact your nearest Authorized B&S Ser-
vice Dealer as listed in the “Yellow Pages”
under “Engines, Gasoline,” “Gasoline En-
gines,” “Lawn Mowers,” or similar category.
b. Air Induction System
•
•
Air cleaner
Intake manifold
c. Ignition System
•
•
Spark plug(s)
Magneto ignition system
d. Catalyst System
•
•
•
Catalytic converter
Exhaust manifold
Air injection system, Pulse valve
4. Claims and Coverage Exclusions
Warranty claims shall be filed in accordance
with the provisions of the B&S Engine War-
ranty Policy. Warranty coverage shall be ex-
cluded for failures of Warranted Parts which
are not original B&S parts or because of
abuse, neglect or improper maintenance as
e. Miscellaneous Items
6. Consequential Coverage
•
Vacuum, temperature, position,
time sensitive valves
and switches
Coverage hereunder shall extend to the fail-
ure of any engine components caused by
the failure of any Warranted Part still under
warranty.
•
Connectors and assemblies
Briggs & Stratton Engines Are Made Under One Or More Of The Following Patents: Design D−247,177 (Other Patents Pending)
5,819,513
5,813,384
5,765,713
5,645,025
5,642,701
5,619,845
5,606,948
5,606,851
5,548,955
5,546,901
5,503,125
5,501,203
5,497,679
5,320,795
5,271,363
5,269,713
5,265,700
5,243,878
5,235,943
5,197,425
5,197,422
5,191,864
5,188,069
5,186,142
5,138,996
5,086,890
5,070,829
5,058,544
5,040,644
5,009,208
4,996,956
4,977,879
4,971,219
4,895,119
4,819,593
4,719,682
4,633,556
4,630,498
4,522,080
4,520,288
4,512,499
4,453,507
4,430,984
DES. 308,871
DES. 308,872
DES. 309,457
DES. 356,951
DES. 361,771
DES. 375,963
6,325,036
6,284,123
6,260,529
6,230,678
6,202,616
6,116,212
6,077,063
6,064,027
6,014,808
5,894,715
5,852,951
5,823,153
18
Download from Www.Somanuals.com. All Manuals Search And Download.
(Cette page ne s’applique que pour le Canada et les Etats−Unis)
La Corporation Briggs & Stratton (B&S), le California Air Resources Board (CARB)
et le Bureau de protection environnementale des EtatsUnis (US EPA)
Garantie sur le système d’échappement (Garantie contre les défectuosités, droits et obligations du propriétaire)
LA GARANTIE SUR LE SYSTÈME D’ÉCHAPPEMENT EST APPLICABLE SUR LES MOTEURS
CERTIFIÉS ACHETÉS EN CALIFORNIE EN 1995 ET LES ANNÉES SUIVANTES ET QUI SONT UTI−
LISÉS EN CALIFORNIE, AINSI QU’AUX MODÈLES CERTIFIÉS DE 1997 ET LES ANNÉES SUI−
VANTES QUI ONT ÉTÉ ACHETÉS ET UTILISÉS AILLEURS AUX ETATS−UNIS (ET APRÉS LE 1ER
JANVIER 2001 AU CANADA).
Déclaration de garantie sur le système d’échappement pour la Californie, les EtatsUnis
Le California Air Resources Board (CARB), le Bureau américain de protection environnementale
pement de votre moteur pour la période de temps mentionnée ci−contre, sauf s’il a fait l’objet
(U.S. EPA) et B& S sont heureux d’expliquer la garantie sur le système d’échappement des petits
moteurs hors−route de votre modèle 2000 et des années ultérieures (SORE). En Californie, les
nouveaux petits moteurs hors route doivent être conçus, construits et équipés pour rencontrer les
standards rigoureux d’antipollution. Ailleurs aux Etats−Unis, les nouveaux moteurs hors route à
bougie d’allumage certifiés pour les modèles de 1997 et plus, doivent rencontrer des normes simi−
laires mises de l’avant par le U.S. EPA. Briggs & Stratton garantit le système de contrôle d’échap−
d’abus, de négligence ou d’un entretien inapproprié.
Votre système de contrôle d’échappement comprend des pièces telles que le carburateur, le filtre à
air, le système d’ignition, le silencieux et le convertisseur catalytique. Il peut aussi comprendre les
connecteurs et autres pièces reliées à l’émission.
Lorsqu’il y a condition à garantie, B&S réparera gratuitement votre petit moteur hors−route incluant
le diagnostic, les pièces et la main d’œuvre.
Couverture de garantie Briggs & Stratton contre toute défectuosité du système de contrôle d’échappement
Les petits moteurs hors route sont garantis contre la défectuosité des pièces du système de contrô−
le d’échappement pour une période de 2 ans, sujette aux conditions stipulées ci−contre. Si n’impor−
te quelle pièce de votre moteur couverte par cette garantie est défectueuse, elle sera réparée ou
remplacée par B&S.
Responsabilités du propriétaire
En tant que propriétaire d’un petit moteur hors route, vous êtes responsable de veiller à l’exécution
de l’entretien requis tel que stipulé dans votre manuel d’opération et d’entretien. B&S vous recom−
mande de conserver tous les reçus couvrant les travaux d’entretien de votre petit moteur hors rou−
te, mais B&S ne peut refuser la garantie en raison d’absence de reçus ou pour défaut d’avoir suivi
tout l’échéancier du programme d’entretien.
En tant que propriétaire d’un petit moteur hors route, vous devez être informé que B&S peut refuser
d’honorer cette garantie si la défectuosité de votre moteur ou d’une partie de votre moteur est due à
un emploi abusif, une négligence, un entretien incorrect ou une modification non approuvée.
Vous avez la responsabilité d’apporter votre petit moteur hors route à un détaillant autorisé B&S
aussitôt que survient un problème. Les réparations sous garantie doivent être complétées dans un
délai raisonnable ne devant pas excéder 30 jours.
Si vous avez des questions relativement à votre garantie, vos droits et responsabilités, veuillez
communiquer avec un représentant de service B&S au numéro 1−414−259−5262.
La garantie du système d’échappement est une garantie contre les défectuosités. Les défectuosi−
tés sont jugées en fonction d’une utilisation normale du moteur. La garantie n’est pas reliée à un
test d’échappement effectué à l’intérieur.
Dispositions de la garantie du système d’échappement Briggs & Stratton
Ce qui suit concerne les dispositions spécifiques relativement à votre garantie sur le système de contrôle d’échappement. C’est une addition à la garantie B&S pour les moteurs non réglementés contenue
dans le manuel d’entretien et d’utilisation.
1. Pièces sous garantie
3. Aucuns Frais
La couverture de cette garantie ne s’applique que sur les pièces listées ci−contre (les parties
du système de contrôle d’échappement) dans la mesure où ces pièces étaient présentes sur le
moteur au moment de l’achat.
La réparation ou le remplacement de toute pièce sous garantie sera effectuée sans aucuns
frais pour le propriétaire, incluant les frais de main d’œuvre pour le diagnostic afin de détermi−
ner si la pièce sous garantie est défectueuse, conditionnel à ce que le diagnostic soit effectué
chez un détaillant autorisé B&S. Pour la garantie relative au système d’échappement, commu−
niquez avec le détaillant autorisé B&S le plus proche tel que listé dans les pages jaunes de
votre localité sous la rubrique moteur à essence, tondeuse ou autre catégorie similaire.
a. Système de dosage du carburant
•
•
•
Système d’enrichissement de démarrage à froid
Carburateur et parties internes
Pompe à essence
4. Réclamations et exclusions de la couverture.
Les réclamations de garantie doivent être complétées en accord avec les dispositions de la
politique de garantie B&S. La garantie ne couvre pas les défectuosités de pièces qui ne sont
pas des pièces d’origine B&S ou dans le cas d’abus, négligence ou d’un entretien inapproprié.
La garantie B&S ne couvre pas les défectuosités de pièces sous garantie qui ont fait l’objet
d’ajouts, ont été modifiées ou de pièces qui ne sont pas des pièces B&S d’origine.
b. Système d’induction d’air
•
Filtre à air
Tubulure d’admission
•
c. Système d’ignition
•
Bougies d’allumage
Système d’allumage électromagnétique
5. Entretien
•
Toute pièce sous garantie qui n’est pas remplacée au moment requis selon le manuel d’entre−
tien ou qui est planifiée seulement pour une inspection régulière sous la mention « réparer ou
remplacer si nécessaire » est garantie contre toute défectuosité pour la période de garantie.
Toute pièce sous garantie qui est planifiée pour un remplacement tel que requis dans l’entre−
tien est garantie contre toute défectuosité seulement pour la période de temps qui va jusqu’au
premier remplacement prévu pour cette pièce. Toute pièce de remplacement équivalente en
performance et durabilité peut être utilisée pour l’entretien ou la réparation. Le propriétaire est
responsable de l’exécution de tout entretien requis tel que défini dans le manuel d’instruction
B&S sur l’entretien et la réparation.
d. Système catalyseur
•
•
•
Convertisseur catalytique
Collecteur d’échappement
Système d’injection d’air ou à pulsion
e. Autres pièces utilisées dans les systèmes ci−haut mentionnés
•
Soupapes et interrupteurs de dépression, de température, de position.
Connecteurs et assemblages.
•
2. Durée de la couverture
6. Couverture indirecte
B&S garantit le propriétaire initial et tous les acheteurs subséquents que les pièces sous ga−
rantie sont exemptes de vice de matière ou de fabrication qui pourraient causer des défectuosi−
tés des pièces sous garantie pour une période de deux ans à partir de la date à laquelle le mo−
teur a été livré à l’acheteur.
La couverture ci−contre s’étend à toute défectuosité des composantes du moteur causée par
la défectuosité de n’importe quelle pièce couverte par la garantie et dont la garantie est encore
en vigueur.
Consultez les informations sur la période de durabilité d’émission et l’INDICE d’air sur l’étiquette d’émission de votre moteur
Les moteurs qui sont certifiés conformes aux normes standards d’émission du California Air Resources Board (CARB) Tier 2, doivent afficher l’information concernant la période de durabilité du système
d’émission et l’INDICE d’air. Cette information est indiquée sur les étiquettes apposées sur les moteurs par Briggs & Stratton.
Lapériode de durabilité d’émission indique le nombre d’heures d’utilisation normale pour lequel le moteur est certifié conforme aux normes d’émission sous réserve d’un entretien approprié tel qu’indiqué dans
le manuel d’opération et d’entretien. Les catégories suivantes sont utilisées :
Modéré
Intermédiaire
Prolongé
le moteur est certifié conforme pour 125 heures d’utilisation normale.
le moteur est certifié conforme pour 250 heures d’utilisation normale.
le moteur est certifié conforme pour 500 heures d’utilisation normale.
Par exemple, une tondeuse de modèle standard est utilisée environ 20 à 25 heures par année. Par conséquent, la période de durabilité d’émission d’un moteur dans la catégorie intermédiaire pour ce type de
tondeuse équivaut à 10 à 12 ans.
L’indice d’air est un nombre qui décrit le niveau relatif d’émission pour une catégorie spécifique de moteur. Plus l’indice d’air est bas, plus le moteur est écologique. Cette information est indiquée sous une
forme graphique sur l’étiquette d’émission.
er
À compter du 1 juillet 2000, surveillez la période de conformité d’émission sur les étiquettes
er
Après le 1 juillet 2000, certains moteurs B&S seront certifiés conformes aux normes environnementales d’émission standard du United States Environmental Protection Agency (US EPA) Phase 2. Pour les
moteurs certifiés pour la Phase 2, la période de conformité d’émission mentionnée sur les étiquettes indique le nombre d’heures d’utilisation pour lequel le moteur rencontre les normes fédérales. Pour les
moteurs de force moindre que 225 cc, la catégorie C = 125 heures, B = 250 heures et A = 500 heures. Pour les moteurs de 225 cc et plus, la catégorie C = 250 heures, B = 500 heures et A = 1000 heures.
Le remplacement du moteur portant le modèle de série
INFORMATIONS IMPORTANTES
470000 est 752 cc.
CORPORATION BRIGGS & STRATTON
FAMILLE YBSXS.3192VA
CE MOTEUR EST CONFORME AUX NORMES
ANTIPOLLUTION 2000 2001 DE CALIFORNIE
274812
Le remplacement du moteur portant le modèle de série
540000 est 895 cc.
-
POUR LES PETITS MOTEURS HORS ROUTE ET
AUX NORMES ENVIRONNEMENTALES
AMÉRICAINES (EPA PHASE 2) POUR LES
PETITS MOTEURS HORS ROUTE. CONSULTEZ
LE MANUEL DU PROPRIÉTAIRE POUR LES
SPÉCIFICATIONS, L’ENTRETIEN ET LES
AJUSTEMENTS. CONFORME À LA PÉRIODE
D’ÉMISSION EPA : CATÉGORIE : C
Ceci est une représentation des étiquettes d’émission
que vous retrouverez sur les moteurs certifiés :
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
|