Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Instructions
Work Area Safety
1. Safety Instructions
IMPORTANT: To prevent electric shock, fire and/or personal injury
or damage, read this user’s manual first and observe the following
safety instructions.
1.1 Work Area Safety
Always perform automotive testing in a safe environment.
Keep your work area clean and well lit. Cluttered benches and
dark areas may cause accidents.
Keep clothing, hair, hands, tools, test equipment, etc. away from
all moving or hot engine parts.
Operate the tool in a well-ventilated work area.
Do not operate the tool in explosive atmospheres, such as in the
presence of flammable liquids, gases, or heavy dust.
Keep a fire extinguisher suitable for gasoline/chemical/electrical
fires nearby.
Do not use the tool around corrosive chemicals which can ruin
the photo quality.
Keep bystanders, children and visitors away while operating the
tool.
Keep the tool dry, clean, free from oil, water and grease. Use a
mild detergent on a clean cloth to clean the outside of the tool
when necessary.
1.2 Electrical Safety
Avoid body contact with grounded surfaces such as pipes,
radiators, ranges and refrigerators.
Do not expose the tool to rain or wet conditions. Water entering
the tool will increase the risk of electric shock.
Do not abuse the cord. Never use the cord for carrying, pulling,
or unplugging the tool. Keep cord away from heat, oil, sharp
edges or moving parts.
If operating the tool in a damp location is unavoidable, use a
ground fault circuit interrupter (GFCI) to protect supply.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Instructions
Personal Safety
1.3 Personal Safety
Do not use the tool while tired or under the influence of drugs,
alcohol, or medications. A moment of interruption can result in
serious personal injury.
Do not over-reach. Keep proper footing and balance at all times.
Proper footing and balance enables better control of the tool in
unexpected situations.
Always wear safety eye protection that meets ANSI standards.
Do not wear loose clothing or jewelry. Keep your hair, clothing,
and gloves away from moving parts. Loose clothes, jewelry, or
long hair can be caught in moving parts.
Do not place the tool on any unstable cart or surface. The tool
may fall causing serious injury to a person or serious damage to
the tool itself.
Never spill liquid on the display units. Liquid increases the risk
of electric shock and damage to the tool.
Do not use the tool for personal or medical use in any way.
The product is not shock-resistant. Do not use it as a hammer or
drop it.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Description, Specification and Tool Components
Description
2. Description, Specifications and Tool
Components
2.1 Description
The Inspection Camera is an ideal and powerful tool for inspecting
difficult-to-reach areas normally hidden from sight. It is a completely
digital platform that features the function of capturing and recording
photos and videos either on its internal memory or on removable SD
cards (not included). The ergonomic tool not only features a 3.5" full
color LCD screen, multi-language interface and viewing capacity as
close as 1" with crystal clear output, but also offers the capacity to
view real time images directly connected to a TV and upload captured
photos and videos to a PC. Accessories (magnet, hook and mirror) are
included to attach to the imager head to provide application flexibility.
2.2 Specifications
Indoor
Recommended use
Optimal viewing
Distance
1" to 14"(2.5cm to 35.6cm)
640 x480
Image capture
Screen type
display
3.5" TFT LCD
320 x 240
Display resolution
Built-in rechargeable lithium-ion battery
pack (3.7 Volt)
Power supply
Tested battery life
Dimensions
5-6 hours of continuous use
255 x 108 x 36mm (10" x 4.25" x 1.42")
Net: 0.6 kg (1.3 lbs);
Gross: 2.3 kg (5.1lbs)
Weight
Internal memory or SD card (SD card is
optional and not included)
Recording
medium
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation and Connection
Image controls
Description
Zoom, low light vision
Fully adjustable LED
Lighting
1m (3') -- expandable to 6m (19')
w/optional extensions (not included)
Cable reach
8.5mm (0.33")
Imager head
waterproof
Imager head and cable to 3m (10')
USB, video out and earphone ports
Additonal ports
Main unit: 32°F to 113°F (0°C to 45°C);
Cable: 14°F to 176°F (-10°C to 80°C)
Operating temp.
Storage temp.
-4°F to 158°F (-20°C to 70°C)
5% - 95% non-condensing (display unit)
RCA
Operating
humidity
Video output
2.3 Accessories Included
1) Protective carrying case
2) User’s Manual
3) Imager head and cable (8.5mm)
4) Magnet, hook and mirror
5) Charger
6) USB cable
7) Video-out cable
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation and Connection
Tool Components
2.4 Tool Components
Note: Because of continuing improvements, actual product may
differ slightly from photo.
The Inspection Camera comes with the following items:
Fig. 1
1) LCD Screen – Indicates still images and videos.
2) Cable – Connects to the tool while in use.
3) Cable Connector – Connects the display unit to the imager head
and cable.
4) Imager Head – Connects to the cable to view real-time images.
5) Rubber Boot – Protects the tool casing.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation and Connection
Tool Components
Fig. 2
6) Accessory Magnet – Picks up small metal objects such as
dropped rings or screws on the floor.
7) Accessory Hook – Unclogs obstacles and picks up wires in pipes
or confined areas.
8) Accessory Mirror – Helps users look around corners and see
inside difficult to reach areas.
2.5 Buttons and Ports
Fig. 3
A. Power Button – Turns on/off the tool.
B. Setting/Back Button – Moves to the primary settings screen, or
when pressed again, returns to the last viewed screen.
C. Camera/Video Button – Captures photos or videos.
D. Play Button – Changes to play mode to play captured photos
and videos.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation and Connection
Tool Components
E. Trash Can/Reverse Button – Deletes captured photos and
videos in the play mode. Pressing again will control the direction
of the real-time image and video in the live screen. The real-time
image and video will do a horizontal reverse or a vertical reverse.
F. LEFT Arrow LED Lighting Adjusting Button – Uses left
arrow button to decrease LED brightness in the camera mode.
G. RIGHT Arrow LED Lighting Adjusting Button – Uses right
arrow button to increase LED brightness in the camera mode.
H. UP Arrow Zoom Adjusting Button – Uses up arrow button to
zoom in while in the camera mode.
I. DOWN Arrow Zoom Adjusting Button – Uses down arrow
button to zoom out while in the camera mode.
J. DC Power Source Port – Connects the tool to the supplied
charger for battery charging.
K. Video-out Port – Connects the tool to a TV with the supplied
video-out cable to view the real-time image.
L. Earphone Port – Connects an optional earphone/microphone.
M. Charging Indicator Light – When the battery is charging, the
charging indicator light is red. When the battery is fully charged,
the charging indicator light changes to green.
N. Mini USB Port – Connects the tool to a computer with the
supplied USB cable to upload and view captured photos and
videos.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation and Connection
Accessories Installation
3. Installation and Connection
3.1 The Imager Head and Cable Installation
To use the tool, the imager head and cable must be connected to the
display unit. To connect the cable to the display unit, make sure the
key and slot (Fig. 4) are properly aligned. Once they are aligned, slide
the connecting sleeve up to the threads on the cable, and finger-tighten
to hold the connection firmly in place.
Fig. 4
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation and Connection
Accessories Installation
3.2 Accessories Installation
The three accessories include a magnet, a hook and a mirror (Fig. 2).
All are attached to the imager head in the same manner. Hold the
imager head as shown in Fig. 5.
Fig. 5
Slip the end of the accessory over the tip of the imager head to fix the
accessory as shown in Fig. 6.
Fig. 6
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation and Connection
SD Card Installation
3.3 SD Card Installation
NOTE: The SD card slot provides for additional memory. The SD
card is optional and not included. Different SD cards can be used to
insert into the SD card slot.
To insert an SD card into the SD card slot, make sure the contacts are
facing towards the slot and the angled portion of the card is facing
down. When the SD card is installed, a small SD card icon will appear
at the top right portion of the screen. To remove an SD card, gently
push the SD card inward and then release to eject it from the card slot.
3.4 USB Cable Connection
Use the supplied USB cable to connect the tool to a PC to upload and
view captured photos and videos. A “USB Connected” message will
appear on the screen as shown. (Fig. 7)
Fig. 7
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation and Connection
Video-Out Cable Connection
3.5 Video-Out Cable Connection
Insert the video-out cable into the video-out port of the tool and the
other end of the cable into the video-in port of a TV. The LCD screen
will output a high quality real-time image.
3.6 Earphone Connection
Connect an earphone with microphone (optional, not included) to the
earphone port of the tool. Speak into the microphone to record your
voice.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Battery Charging Precautions
Battery Charging Safety
4. Battery Charging Precautions
IMPORTANT: To reduce the risk of serious injury, read these
precautions and the label on the charger carefully before using.
Lithium batteries store a large amount of energy and will vent fire or
explode if mistreated.
4.1 Battery Charging Safety
Do not probe charger with conductive objects.
Do not use the charger if it has been dropped or damaged in any
way.
Charge the battery in temperatures above 41°F (5°C ) and below
113°F (45°C ).
When in use, keep the charger out of heat, high voltage and away
from children.
Use only the supplied charger. Do not charge the battery over 24
hours.
Do not allow anything to cover the charger while in use.
Unplug the charger from its outlet before attempting any
maintenance or cleaning.
Do not store the charger in damp, wet or explosive environments.
Do not open the charger housing. Have repairs performed only at
authorized locations.
Do not charge the battery near fire or in the sunlight.
Proper care will prevent serious damage to the charger.
4.2 Battery and Charger Specifications
100-240 VAC/12 VDC 50/60Hz
5V DC
Input
Output
3.7V lithium-ion
Battery Type
Battery
Capacity
4500 mA
0.3A/1A (DC)
Input Current
5-6 hours
Charging Time
Cooling
Passive convention cooling (No fan)
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Battery Charging Precautions
Charger Inspection
4.3 Charger Inspection
CAUTION: Before using, inspect the charger and correct any
problems. Set up the charger according to these procedures to
reduce the risk of injury from electric shock, fire and other causes,
and to prevent tool damage.
1) Make sure the charger is unplugged. Inspect the power cord and
charger for damage or modifications, or broken, worn, missing,
misaligned or binding parts. If any problems are found, do not
use the charger until the parts have been repaired or replaced.
2) Clean any oil, grease or dirt from the tool especially on the
buttons. This helps to prevent the tool from slipping from your
hands and allows proper ventilation.
3) Check that the warning label on the charger is intact and
readable.
4) Select an appropriate location for the charger before using.
Check the following:
The charger must be between 41°F (5°C) and 113°F (45°C)
for charging. If the temperature goes below or exceeds this
range at any point during charging, the operation will be
suspended until brought back to the correct temperature
range.
Inspect that the plug fits correctly into the desired outlet.
The charger needs a clearance of at least 4" (10 cm) on all
sides to maintain a proper operating temperature.
4.4 Battery Charging Procedures
NOTE: A new battery reaches full capacity after approximately 5
charging and discharging cycles.
The tool has a 3.7V built-in lithium-ion rechargeable battery. When
the battery is low, a “Battery critically low!” message appears and
suggests you to charge the battery in time. (Fig. 8)
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Battery Charging Precautions
Battery Charging Procedures
Fig. 8
There are two means of charging battery:
1) To charge the battery with the charger: Locate the DC power
source port of the tool. With dry hands, connect the tool to the
charger and plug in the charger to start charging.
2) To charge battery by USB cable: Locate the USB port of the tool.
With dry hands, connect the tool to a PC with the USB cable to
start charging.
The battery will begin charging automatically. While the
battery is charging, the charging indicator light is red.
When the battery is fully charged, the charging indicator light
turns green.
Once the battery is charged, it may remain until it is ready to be
used. There is no risk of over-charging the battery. When the
battery has been fully charged, the charger automatically
switches to retention charging.
Unplug the charger from outlet once charging completes.
)
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation Instructions
Basic Operation
5. Operation Instructions
IMPORTANT: Always wear safety eye protection to protect your eyes
against dirt and other objects. Follow the operation instructions to
reduce the risk of injury from electric shock, entanglement and other
causes.
5.1 Basic Operation
NOTE: When in operation, the cable can be bent into a specific
shape. This may help to maneuver the cable into confined areas.
1) Hold the tool with the LCD screen facing you and press the
Power button to turn it on. Wait for several seconds. While the
unit is booting up an introductory screen is displayed. Then the
live screen is displayed, where you can do most of your work.
2) Press the OK button to capture photos in the camera mode. Press
the OK button to begin capturing videos in the video mode. Press
the Camera/Video button to switch between the two modes.
3) Press the UP and DOWN arrow buttons to zoom in or out. A
zoom indicator bar is displayed as you make the adjustment.
4) Press the LEFT and RIGHT arrow buttons to increase or
decrease the LED brightness while in the camera mode. A
brightness indicator bar is displayed as you adjust LED light
intensity.
5) Press the Play button to view captured photos and videos.
6) Press the Trash Can button to delete captured photos and videos
as needed when playing back captured photos and videos.
7) Press the Reverse button to control the direction of the real-time
image and video as needed in the live screen.
8) Press the Setting/Back button to enter Setup mode or return to
the last viewed screen.
9) Use the supplied accessories to provide application flexibility.
10) Use the supplied USB cable to connect the tool to a PC to upload
and view captured photos and videos.
11) Connect the supplied video-out cable to the video-out port of the
tool and the other end of the cable to the video-in port of a TV to
view a high quality real-time image.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation Instructions
Operation Precautions
12) Connect the optional earphone with microphone to the earphone
port of the tool. Speak into the microphone to record your voice.
5.2 Operation Precautions
Use the tool only as directed. Do not operate the tool unless the
user’s manual has been read thoroughly and proper training has
been completed.
The display unit is not waterproof. The imager head and cable
are waterproof, but not acid-proof or fireproof.
Avoid submersing the imager head and cable into corrosive, oily
places and be sure to keep the imager head and cable away from
high temperature objects.
Do not immerse the tool and display unit in water. Such
measures reduce the risk of electric shock and damage.
Do not use excessive force to insert or withdraw the imager head
and cable. This may result in damage to the tool or inspection
area.
Do not use the imager head and cable to modify surroundings,
clear pathways or clogged areas.
Do not place the imager head and cable into anything or
anywhere that may contain a live electrical charge or moving
parts, which increase the risk of electric shock or entanglement
injuries.
Do not use the tool for personal inspection or medical use in any
way. This is not a medical tool.
Do not eat or smoke while operating the tool. Use hot, soapy
water to wash hands and other body parts exposed to drain
contents after using the tool to inspect drains and other areas that
may contain chemicals or bacteria. This will help prevent
contamination with toxic or infectious material.
When the inspection is completed, carefully withdraw the imager
head and cable from the inspection area.
Store idle components out of the reach of children and other
untrained persons.
Maintain the tool with care. Properly maintained tools are less
likely to cause injury.
Do not drop the tool, if the tool is dropped accidently, check for
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation Instructions
Tool Inspection
breakage and any other condition which may affect its operation.
Use only accessories that are recommended by the manufacturer
for the tool.
Dry your hands before operating the tool or charging the battery.
Always use appropriate personal protective equipment while
handling and using the tool. Appropriate personal protective
equipment always includes safety glasses and gloves, and may
include latex or rubber gloves, face shields, goggles, protective
clothing, respirators and steel toed footwear.
Protect against excessive heat. The tool should be kept away
from heat sources such as radiators, stoves or others products
that produce heat. Do not use the tool near moving machinery or
areas where the temperature will exceed 113°F (45°C).
Store the tool, charger and all cables in a locked area out of the
reach of children and people unfamiliar with the tool.
5.3 Tool Inspection
WARNING: Before using, inspect your tool and correct any
problems to reduce the risk of serious injury from electric shock and
other causes and to prevent damage to the tool.
Make sure the power is OFF.
Clean any oil, grease or dirt from the tool, especially on the
buttons and ports. This helps to prevent the tool from slipping
from your hands.
Inspect the imager head lens for condensation. To avoid
damaging the tool, do not use the tool if condensation forms
inside the imager head. Let the water evaporate before using
again.
Inspect the full length of the cable for cracks or damage. A
damaged cable could allow water to enter the tool and increase
the risk of electric shock.
Make sure the connections between the display unit and imager
head and cable are tight. All connections must be properly
assembled for the cable to be waterproof.
Check if the warning label is present, firmly attached and
readable. Do not operate the tool without the warning label.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation Instructions
Tool and Work Area Set-Up
Turn on the power and make sure the tool starts up as described
in the Basic Operation section.
If the tool does not work well after turning it on, have the tool
checked by a qualified technician. Any tool that cannot be
controlled with the power button is dangerous and must be
repaired.
NOTE: Please check following methods to avoid injury.
FOR WALLS: For inspecting inside walls, shut off the circuit
breaker to the whole house before using the tool.
FOR PIPES: If you suspect a metal pipe could contain an
electrical charge, have a qualified electrician check the pipe
before using.
FOR AUTOMOBILES: Be sure the automobile is not running
during inspection. Metal and liquid under the hood may be hot.
Do not get oil or gas on the imager head.
5.4 Tool and Work Area Set-Up
CAUTION: Set up the tool and work area according to these
procedures to reduce the risk of injury from electric shock,
entanglement, and other causes and prevent tool damage.
1) Check work area for:
Sufficient lighting.
Do not work in an area until flammable sources have been
identified and corrected. The tool is not explosion proof and
can cause sparks.
Do not use the tool while standing in water.
2) Check the area and determine if the Inspection Camera is the
correct tool for the job.
Check the access points to the area.
Check if there is any electric power supplied to the area to
be inspected.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation Instructions
Tool and Work Area Set-Up
Check if any liquids will be contacted during inspection.
The imager head and cable are waterproof to a depth of 3m
(10'). Greater depths may cause leakage into the imager
head and cable and cause electric shock or damage the tool.
The display unit is not waterproof and should not be
exposed to wet conditions.
Check if any chemicals are present, especially in the case of
drains. Chemicals may damage the tool.
Check the temperature of the area. The working temperature
of the tool is between 32°F (0°C ) and 113°F (45°C).
Check if any moving parts are present in the area.
3) Make sure the tool has been properly inspected.
4) Install the correct accessories for use in the appropriate
application.
CAUTION: Make sure the tool has been powered off before
performing maintenance.
Tool maintenance must be performed only by qualified repair
personnel. Maintenance performed by unqualified repair
personnel could cause injury.
When maintaining, use only identical replacement parts. Use of
unauthorized parts or failure to follow maintenance instructions
may create a risk of electric shock or injury.
Do not attempt to take any pieces of the tool apart unless directed
by the manual.
Follow instructions to change accessories.
Do not use acetone to clean the tool. Instead, use only alcohol to
swab the connections. Avoid rubbing too hard on the LCD
screen. After using, wipe the display unit clean gently with a dry
cloth.
Upon the completion of any maintenance of the tool, ask
qualified repair personnel to perform safety checks to examine if
the tool is in proper operating condition.
Stop using the tool if it starts smoking or emitting noxious
fumes.
Always handle the tool with care. It is not shock-resistant.
Do not disassemble the tool beyond what is shown in the manual.
Doing so will void your warranty.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation Instructions
On Screen Navigation
5.5 On Screen Navigation
1) Splash Screen
When the tool is powered on, the first screen displayed is
referred to as the splash screen. (Fig. 9) This screen tells you the
tool is booting up. Once the tool is fully powered up, the screen
will automatically switch to the live screen.
Fig. 9
2) Live Screen
The live screen is where you will do most of your work. A live
image of what the imager head sees is displayed on the screen.
You can zoom in or out, adjust LED brightness, rotate images
and video, view and capture photos and videos from this screen.
3) Switching from Still Image Capture to Video Capture
The tool defaults to still image capture when powered on. Press
the Video/Camera button to switch between still image capture
and video capture as needed.
4) Adjusting LED Brightness
Press the RIGHT and LEFT arrow buttons on the key pad (in
the still camera mode) to increase or decrease the LED
brightness. A brightness indicator bar will be displayed on the
screen as you adjust the brightness. (Fig. 10)
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation Instructions
On Screen Navigation
Fig. 10
5) Zooming
Press the UP and DOWN arrow buttons while in the still camera
mode to zoom in or out. A zoom indicator bar will be displayed
on the screen as you adjust the zoom. (Fig. 11)
Fig. 11
6) Entering the Primary Settings Screen
Pressing the Setting button while in the live screen will take you
to the primary settings screen. (Fig. 12) Pressing the Back
button at any point will take you back to the live screen.
Fig. 12
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation Instructions
7) Capturing a Photo
On Screen Navigation
When in the live screen, make sure the camera icon is present at
the top left portion of the screen. (Fig. 13) Press the OK button
to capture a photo. The image is saved to the internal memory or
SD card. The total number of photos is displayed below the
camera icon. The number will increase or decrease as different
capacity SD cards are used, or the photo quality is adjusted.
Fig. 13
8) Capturing a Video
While in the live screen, make sure the video icon is present at
the top left portion of the screen. (Fig. 14) Press the OK button
to start capturing video. A record icon will appear at the top right
portion of the screen, just below battery capacity icon. This
shows that video is capturing. The time at the top left portion,
just below video icon will begin counting down. This indicates
how much video you can store in the internal memory or SD
card. Press the OK button again to stop capturing a video.
Fig. 14
If you wish to record sound, you can insert the optional earphone
with mic into the earphone port of the tool. When capturing a
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation Instructions
On Screen Navigation
video, you are recording simultaneously. It may take a few
seconds to save the captured video to the internal memory or SD
card.
9) Playing Back and Deleting Captured Photos and Videos
Press the Play button on the key pad to display two modes for
you to select. Photos and videos that were captured will be
displayed on the screen. Use the LEFT and RIGHT arrow
buttons to move from Photo mode to Video mode. (Fig. 15 and
Fig. 16)
Fig. 15
While Photo mode is highlighted (Fig. 15), press the OK button.
The stored photos will be displayed. Use the LEFT and RIGHT
arrow buttons to play back captured photos one after another.
Use the UP and DOWN arrow buttons to zoom in and out.
Fig. 16
While Video mode is highlighted (Fig. 16), press the OK button.
The stored videos will be displayed. Use the LEFT and RIGHT
arrow buttons to play back captured videos one after another.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation Instructions
On Screen Navigation
While in the photo mode, select a photo and press the OK button.
A bar will appear with record mode in the middle of the screen.
(Fig. 17)
Fig. 17
Inserting the optional earphone with microphone and pressing
OK button will begin recording (Fig. 18) and timing.
Fig. 18
Press the OK button as desired to stop recording and then
the“ ” icon will appear.
Press the OK button to play the recording. Press OK again to
pause the recording in the record mode. (Fig. 19 and Fig. 20)
Fig. 19
Fig. 20
If you wish to delete the recording, use LEFT and RIGHT
arrow buttons to select “ ” icon then press OK. (Fig. 21)
Fig. 21
While in the video mode, selecting a video which has been
recorded and pressing the OK button will start playing the
recording. Press the OK button again to pause playing the
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation Instructions
On Screen Navigation
recording. Press the LEFT button to fast forward recording and
the RIGHT button to reverse the recording. Press the UP button
to stop playing the recording.
Either in the Photo mode or in the Video mode, press the Trash
Can button to delete captured photos and videos, and a “Are you
sure you want to delete this file?” message appears on the
screen. (Fig. 22 and Fig. 23) Use the LEFT and RIGHT arrow
buttons to select Yes or No, then press the OK button to save
your selection.
Fig. 22
Fig. 23
When you delete all the photos and videos, a “No Files
Available” message appears on the screen. (Fig. 24)
Fig. 24
10) Entering the Secondary Settings Screen
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation Instructions
On Screen Navigation
While in the Primary Settings Screen (Fig. 12), select Advanced
Settings from Setup and then press OK button, you will enter
the secondary settings screen (Fig. 25) where you can set the
Date and Time, Restore Defaults and select a Language as
needed. Press the Back button at any point to go back to the
primary settings screen and press it again to go back to the live
screen.
Fig. 25
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation Instructions
Icons
5.6 Icons
1)
Battery Capacity - Fully charged battery.
SD Card - Indicates an SD card has been inserted into the tool.
Still Camera - Indicates the tool is operating in still camera
2)
3)
mode.
4)
5)
Video Camera - Indicates the tool is operating in video camera
mode.
Record sound - Push OK to record sound in the photo play
mode.
6)
7)
Record - Press OK to record in the photo record mode.
Stop - Press OK to stop playing recording in the photo record
mode.
8)
9)
Play - Press OK to play recording in the photo record mode.
Pause - Press OK to pause playing recording in the photo record
mode.
10)
Delete - Press OK to delete the recording in the photo record
mode. (You will be prompted: “Are you sure you want to delete this
file,” before deletion is completed.)
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation Instructions
11) Advanced settings
Advanced Settings
Advanced Settings is the default mode from the Setup menu.
Press the Setting button to enter Setup.
Fig. 26
Select Advanced Settings from Setup and press the OK button
to modify advanced settings.
Fig. 27
When necessary, use the UP and DOWN arrow buttons to select
Date and Time, Restore Defaults and Language from
Advanced Settings.
12)
– Displays color or black/white.
Color is the default mode.
Select Color or Black/White from Setup and press the OK
button.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation Instructions
Advanced Settings
Fig. 28
Use the LEFT and RIGHT arrow buttons to select from Color
mode to Black/White mode, then press the OK button to save
your selection.
If you wish to view or capture color images and videos, select
Color from Setup.
Fig. 29
If you wish to view or capture black/white images and videos,
select Black/White from Setup.
Fig. 30
13)
– Asks if format media.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation Instructions
Advanced Settings
Select Format Media from Setup and press the OK button.
Fig. 31
If you wish to format media, select Format Media from Setup
and press the OK button and then use the LEFT and RIGHT
arrow buttons to select Yes, then press the OK button to save
your selection.
Fig. 32
If you do not wish to format media, use the LEFT and RIGHT
arrow buttons to select No to return to the previous menu.
Fig. 33
If you select Yes, a message “Warning - this will erase ALL
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation Instructions
Advanced Settings
files in memory” appears on the screen. Press the OK button to
save your selection and return to the previous menu.
Fig. 34
If you do not wish to format media, select No to return to
previous menu.
Fig. 35
14)
– Displays firmware version.
Select Help from Setup and press OK button to display
Firmware Version.
Fig. 36
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation Instructions
Advanced Settings
Fig. 37
15)
– Sets date and time.
When you enter Advanced Settings, select Date and Time and
press the OK button.
Fig. 38
Use the UP and DOWN arrow buttons to set the exact date and
time while using the LEFT and RIGHT arrow buttons to move
from one item to another and press the OK button to save.
Fig. 39
16)
– Ask to restore factory defaults.
Select Restore Defaults from Advanced Settings and press the
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation Instructions
Advanced Settings
OK button.
Fig. 40
If you wish to restore factory defaults, use LEFT and RIGHT
arrow buttons to select Yes, then press the OK button to save
your selection.
Fig. 41
If you do not wish to restore factory defaults, select No to return
to the previous menu.
Fig. 42
17)
– Displays multi-language interface.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Operations Instructions
Advanced Settings
English is the default language.
Select Language from Advanced Settings and press the OK
button.
Fig. 43
Use the LEFT and RIGHT arrow buttons to switch among
English, Spanish, French, German and Dutch. Select the
desired language and press the OK button to save your selection.
Fig. 44
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
6. Troubleshooting
POSSIBLE
REASONS
SYMPTOMS
SOLUTIONS
Cable connection
is loose.
Check and
reattach.
Display is on, but does not
show image.
Inspect imager
head and clean
if needed.
Imager head is
covered by debris.
LEDs on imager head are dim
at max brightness, display
changes between black and
white, and/or the color display
turns itself OFF after a short
period.
Low battery.
Dead battery.
Charge battery.
Charge battery.
The tool will not turn on.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts List and Diagram
7. Parts List and Diagram
Item # Description
1
2
Rubber Cover
Lens
3
Skin
4
5
Front Shell
Button
6
LCD
7
PCB
8
9
Power Switch
Screw
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
Battery
Back Shell
Screw
Screw
Square Gasket
Hex Nut
Connector
Cable Connector
Ring
Female Connector
Ring
Ring
Imager Head and Cable
Mirror (not shown)
Magnet (not shown)
Hook (not shown)
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts List and Diagram
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
|
