Ezy Carve
Electric Knife
Breville is a registered trademark of Breville Holdings Pty. Limited
ABN 98 000 092 928
Breville Customer Care Centre
Australian Customers
Breville Customer Care Centre
✉
Locked Bag 2000
Botany NSW 2019
Australia
Customer Service
Ph: 1300 139 798
✉
Fax (02) 9384 9601
Email Customer Service
New Zealand Customers
Breville Customer Service Centre
Private Bag 94411
Greenmount
✉
Auckland, New Zealand
Customer Service Ph: 07 271 3980
Fax 0800 288 513
✉
Email Customer Service
PRINTED ON
RECYCLED PAPER
© Copyright. Breville Holdings Pty. Limited 2004
Due to continual improvements in design or otherwise, the product you
purchase may differ slightly from the one illustrated in this booklet.
INSTRUCTIONS FOR USE
MODEL BEK5
Model BEK5
Issue 1/01
Download from Www.Somanuals.com. All Manuals Search And Download.
KNOW YOUR BREVILLE EZY CARVE
OPERATING YOUR BREVILLE EZY CARVE
1. Twin Stainless steel blades
2. 150 watts of power
4. Dual safety switch ON/OFF buttons
BEFORE FIRST USE
5. Built-in loop for storage
6. Blade safety guards
Remove all promotional labels and wash the
stainless steel blades in warm, soapy water.
Dry thoroughly.
3. Blade release buttons
1. Interlock the blades together before
inserting into the appliance. To assemble
blades, hold the shaft ends below the
Safety Guards and slip the rivet on the tip
of the other blade (see fig 1). Move
blades together ensuring tips remain
together.
5.
2.
Fig 2
3. Insert the plug into a 230/240v power
outlet and switch on. Ensure the cord is
clear from the blades.
3.
Always ensure blades are
fully locked into position
before operating.
✉
4.
NOTE!
6.
Fig 1
4. Holding the knife with one hand, depress
both the top and bottom ON/OFF
controls to activate the knife. The unit will
not operate unless both controls are
depressed at the same time (see fig 3).
Releasing either of the ON/OFF controls
will automatically stop the knife.
Always use both blades
when operating the
Ezy Carve.
✉
NOTE!
2. Hold assembled blades by the Safety
Guards and insert and slide blades into
the blade slot pushing until both blades
are locked into position. You will hear a
‘click’ sound (see fig 2).
1.
Fig 3
3
4
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING YOUR BREVILLE EZY CARVE
CARE AND CLEANING
(CONTINUED)
ENSURE THE POWER OUTLET
IS SWITCHED OFF AND THE
PLUG REMOVED BEFORE
REMOVING THE BLADES
AND/OR CLEANING.
• Wash the blades in hot soapy water with a
soft cloth or sponge. Rinse thoroughly and
dry completely. Alternatively place blades
into the dishwasher.
AVOID CONTACT WITH
MOVING PARTS. KEEP
HANDS, HAIR, CLOTHING
AND OTHER UTENSILS AWAY
FROM MOVING BLADES
DURING OPERATING TO
PREVENT PERSONAL INJURY
AND/OR DAMAGE TO THE
KNIFE.
THE BLADES OF YOUR EZY
CARVE ARE SHARP! HANDLE
WITH EXTREME CARE. WE
RECOMMEND USING THE
SAFETY GUARDS AT ALL
TIMES PROVIDED WHEN
HANDLING THE BLADES. DO
NOT FIT OR REMOVE THE
BLADES WHILST THE KNIFE
IS CONNECTED TO THE
POWER OUTLET.
• Do not use abrasive scouring pads or
powders on the blades.
• Depress the Blade Release Buttons and
hold the blades by the Safety Guards.
• After cleaning, always store blades in
plastic sleeve provided. To clean motor
housing wipe with a soft damp cloth.
• Ensure the cutting edge of the blades face
downwards. To remove blades pull the
blades firmly out of the slots (Refer fig 4).
• Unlock the blades by sliding apart. Always
hold blades by the Safety Guards when
handling and cleaning.
5. When slicing is completed, turn the
power off at the power outlet and remove
the plug.
DO NOT ALLOW CHILDREN
TO OPERATE THE APPLIANCE
WITHOUT SUPERVISION.
6. Depress and hold both the Blade Release
Buttons on either side of the unit at the
same time holding the blades by the
Safety Guards.
•
7. Ensure the cutting edge of the blades
face downwards. To remove blades pull
the blades firmly out of the slots (see
fig 4).
Fig 4
5
6
|