™
the Infuser
Instruction Booklet
Breville Customer Service Centre
Australian Customers
New Zealand Customers
Mail: PO Box 22
Botany NSW 2019
AUSTRALIA
Mail: Private Bag 94411
Botany Manukau 2163
Auckland NEW ZEALAND
Phone: 1300 139 798
Phone: 0800 273 845
Fax:
(02) 9384 9601
Fax:
0800 288 513
Email: Customer Service:
Email: Customer Service:
Breville is a registered trademark of Breville Pty. Ltd. A.B.N. 98 000 092 928.
Copyright Breville Pty. Ltd. 2013.
Due to continued product improvement, the products illustrated/photographed
in this brochure may vary slightly from the actual product.
BES840 Issue - E13
BES840
Download from Www.Somanuals.com. All Manuals Search And Download.
BREvILLE RECoMMENdS SAFEty FIRSt
BREvILLE RECoMMENdS SAFEty FIRSt
At Breville we are very safety conscious. We design and manufacture consumer products with
the safety of you, our valued customer, foremost in mind. In addition we ask that you exercise
a degree of care when using any electrical appliance and adhere to the following precautions.
IMPoRtANt SAFEGUARdS FoR
ALL ELECtRICAL APPLIANCES
WARNING
Fully unwind the cord before use.
•
Unwind the power cord fully before use.
•
Do not let the power cord hang over
the edge of a bench or table, touch hot
surfaces, or become knotted.
IMPoRtANt SAFEGUARdS
•
•
•
Use only cold, tap water in the water
tank. Do no use any other liquid.
REAd ALL INStRUCtIoNS
BEFoRE USE ANd SAvE FoR
FUtURE REFERENCE
•
•
To protect against electric shock do
not immerse power cord, power plug
or appliance in water or any other
substance.
This appliance is not intended for use
by persons (including children) with
reduced physical, sensory or mental
capabilities, or lack of experience or
knowledge, unless they have been given
supervision or instruction concerning
use of the appliance by a person
responsible for their safety.
Never use the Breville Infuser™ without
water in the water tank.
Ensure the portafilter is firmly inserted
and secured into the brewing head
before using the machine.
Never remove the portafilter during the
brewing operation as the machine is
under pressure.
•
Carefully read all instructions before
operating and save for future reference.
Remove and safely discard any
packaging material and promotional
labels or stickers before using the
Breville Infuser™ for the first time.
•
•
•
•
To eliminate a choking hazard for young
children, remove and safely discard the
protective cover fitted to the power plug
of this appliance.
Do not place the Breville Infuser™ near
the edge of a bench or table during
operation. Ensure the surface is level,
clean and free of water and other
substances.
Do not use the Breville Infuser™ on a
sink drain board.
Do not place the Breville Infuser™ on
or near a hot gas or electric burner, or
where it could touch a heated oven.
•
•
•
Do not move the Breville Infuser™
whilst in operation.
Do not leave the Breville Infuser™
unattended when in use.
Do not touch hot surfaces. Allow the
Breville Infuser™ to cool down before
moving or cleaning any parts.
Do not place anything, other than cups
for warming, on top of the Breville
Infuser™
Always switch off the Breville Infuser™
by pressing the POWER button to ‘Off’,
switch off at the power outlet and unplug
if appliance is to be left unattended,
if not in use, before cleaning, before
attempting to move the appliance,
disassembling, assembling and when
storing the appliance.
•
•
Children should be supervised to ensure
they do not play with the appliance.
It is recommended to regularly inspect
the appliance. Do not use the appliance
if power cord, power plug or appliance
becomes damaged in anyway. Return
the entire appliance to the nearest
authorised Breville Service Centre for
examination and/or repair.
Any maintenance other than cleaning
should be performed at an authorised
Breville Service Centre.
This appliance is recommended for
household use only. Do not use this
appliance for anything other than its
intended use. Do not use in moving
vehicles or boats. Do not use outdoors.
Misuse may cause injury.
The installation of a residual current
device (safety switch) is recommended
to provide additional safety protection
when using electrical appliances. It
is advisable that a safety switch with
a rated residual operating current
not exceeding 30mA be installed in
the electrical circuit supplying the
appliance. See your electrician for
professional advice.
•
•
•
•
•
•
•
Always ensure the Breville Infuser™ is
properly assembled before connecting
to power outlet and operating. Follow the
instructions provided in this book.
•
•
•
The appliance is not intended to be
operated by means of an external timer
or separate remote control system.
Do not use attachments other than
those provided with the Breville
Infuser™.
Do not attempt to operate the Breville
Infuser™ by any method other than those
described in this book.
•
Keep the appliance and accessories
clean. Follow the cleaning instructions
provided in this book.
•
SAvE tHESE
INStRUCtIoNS
Download from Www.Somanuals.com. All Manuals Search And Download.
4
5
FEAtURES oF yoUR BREvILLE PRodUCt
PId tEMPERAtURE CoNtRoL
LoW PRESSURE PRE-INFUSIoN
kNoW
Electronic PID temperature control for
increased temperature stability.
Applies low pressure at the start of the
extraction to gently expand grinds for an
even extraction.
your Breville product
AUto PURGE
ESPRESSo PRESSURE GAUGE
Automatically adjusts water temperature
after steam for optimal coffee temperature.
Indicates the water pressure delivered to
the portafilter during extraction.
tHERMoCoIL HEAtING SyStEM
voLUMEtRIC CoNtRoL
Integrated stainless steel water coil
accurately controls water temperature.
Programmed 1 & 2 cup shot volumes with
manual over-ride.
CoMMERCIAL StyLE StEAM WANd
dRy PUCk FEAtURE
360˚ swivel action for effortless milk
texturing.
Removes excess water from the ground
coffee in the filter basket after extraction
for easy disposal of the coffee puck.
INStANt Hot WAtER oUtLEt
Dedicated hot water outlet for making long
blacks & pre-heating cups.
Download from Www.Somanuals.com. All Manuals Search And Download.
7
kNoW yoUR BREvILLE PRodUCt
kNoW yoUR BREvILLE PRodUCt
A. Power button surround illuminates
Not SHoWN
when machine is switched on.
•
Removable 1.8 litre water tank filled
from the top with integrated water
filtration.
B. Integrated removable tamper for
tamping control.
C. Group head for easy positioning of the
•
Storage tray located behind the drip tray
for storage of accessories.
P
O M
N
L
portafilter.
D. 54mm stainless steel portafilter with
K
J
commercial style spouts.
CUStoM dESIGNEd ACCESSoRIES
E. Extra-tall cup height for coffee mugs
F. Removable drip tray
•
•
Razor Precision Dose Trimming Tool
A
Single wall filter baskets for freshly
ground coffee.
G. Drip tray full indicator
H. 360° swivel action steam wand easily
•
Advanced dual wall filter baskets for
pre-ground coffee.
adjusts to perfect position for texturing.
B
C
D
I. Dedicated Hot Water Outlet
•
•
Stainless steel jug
Measuring spoon
I
J. Steam/Hot Water selector control for
steam and hot water
CLEANING ACCESSoRIES
K. Programmable 1 CUP and 2 CUP
button.
•
•
•
•
Cleaning tool
Cleaning tablets
Cleaning cycle disc
Allen key
L. Steam/Hot Water light illuminates
to indicate that the steam/hot water
function is selected.
H
G
E
F
M. CLEAN ME light indicates when a
cleaning cycle is required.
N. Espresso pressure gauge monitors
espresso extraction pressure.
O. Program button programmable function
that can be personalised with your
favourite espresso volume.
P. Cup warming tray
Download from Www.Somanuals.com. All Manuals Search And Download.
8
9
oPERAtING yoUR BREvILLE PRodUCt
BEFoRE FIRSt USE
FIRSt USE
oPERAtING
Machine Preparation
Initial Start Up
Remove and discard all labeling and
packaging materials attached to your
espresso machine. Ensure you have removed
all parts and accessories before discarding
the packaging.
•
•
•
Fill tank with water
Press POWER on
A pumping sound will be heard. The
machine will reach operating temperature
and go into STANDBy mode.
your Breville product
Clean parts and accessories (water tank,
portafilter, filter baskets and jug) using
warm water and a gentle dish washing liquid
and rinse well. Wipe the outer housing
and drip tray with a soft damp cloth and
dry thoroughly. Do not immerse the outer
housing, power cord or power plug in water
or any other liquid.
FLUSHING tHE MACHINE
It is recommended to complete a water
flushing operation, without ground coffee, to
ensure the machine has been conditioned.
When the machine has reached STANDBy
mode, run the following 2 steps.
The water filter located inside the water tank
will need to be removed before washing the
water tank.
•
Press the 2 CUP button to run hot water
through the group head for 30 seconds.
Activate hot water for 10 seconds.
Repeat this cycle until the water tank
is empty.
•
•
CoNdItIoNING tHE WAtER FILtER
•
Remove filter from the plastic bag and
soak in a cup of water for 5 minutes.
NotE
•
•
Rinse filter under cold running water.
Do not clean any of the parts or
accessories in the dishwasher.
Wash the stainless steel mesh in
the plastic filter compartment with
cold water.
•
•
•
Insert the filter into the filter holder.
Set the dial date 2 months ahead.
To install filter, push down to lock
into place.
•
Slide the water tank into position and
lock into place.
NotE
To purchase water filters contact
Breville Customer Service Centre on
1300 139 798 (Australia) or
0800 273 845 (New Zealand)
Download from Www.Somanuals.com. All Manuals Search And Download.
11
oPERAtING yoUR BREvILLE PRodUCt
FILLING tHE WAtER tANk tRIMMING tHE doSE
oPERAtING yoUR BREvILLE PRodUCt
PRE-PRoGRAMMEd
PRoGRAMMING SINGLE ESPRESSo
SHot voLUME – 1 CUP
•
Ensure the water filter is securely fitted
inside the tank.
Fill the water tank with cold tap water
to the maximum mark on the side of the
tank and slide the water tank back into
position at the back of the machine.
The Razor™ precision dose trimming tool
allows you to trim the puck to the right level
for a consistent extraction.
1. To begin programming, press
the PROGRAM button once. The
machine will beep once and the
program button will begin to flash.
This indicates the machine is in
programming mode.
Press the 1 CUP once. A preset volume of
approximately 30mls will be extracted. The
machine will automatically stop once the
preset volume has been extracted.
•
™
the Razor
Precision dose trimming tool
•
•
Plug the power cord into power outlet
and switch On at power point.
2. Press 1 CUP button to start espresso
extraction. Press 1 CUP again once
desired volume of espresso has been
extracted. The machine will beep
twice to indicate the new 1 CUP
volume has been set.
Press the POWER button to On. The
POWER button surround will flash
while the machine is heating. When the
correct temperature has been reached,
all the button surrounds on the control
panel will illuminate.
Insert the Razor™ into the coffee basket
until the shoulders of the tool rest on the
rim of the filter basket. The blade of the
dosing tool should penetrate the surface
of the tamped coffee.
PRoGRAMMING doUBLE ESPRESSo
1. To begin programming, press the
PROGRAM button once. The machine
will beep once and the program button
will begin to flash. This indicates the
machine is in programming mode.
Rotate the Razor™ dosing tool back and forth
while holding the portafilter on an angle over
the knock box to trim off excess coffee.
NotE
The amount of espresso extracted in
the cup will vary depending on your
grind size and dose amount.
NotE
Check the water level before use and
replace the water daily. The water
tank should be filled with fresh, cold
tap water before each use.
Do not use mineral or distilled water
or any other liquid.
2. Press 2 CUP button to start espresso
extraction. Press 2 CUP again once
desired volume of espresso has been
extracted. The machine will beep
twice to indicate the new 2 CUP
volume has been set.
PRE-PRoGRAMMEd
SHot voLUME – 2 CUP
Press the 2 CUP button once. A preset
volume of approx. 60mls will be extracted.
The machine will automatically stop once
the preset volume has been extracted.
tAMPING tHE GRoUNd CoFFEE
your coffee filter basket is now dosed with
•
Once the grind function has been
completed, carefully withdraw the
portafilter from the grinding cradle,
being careful not to spill any ground
coffee, tap down to collapse and using
the integrated tamper, tamp down firmly
(approx. 15–20 kg of pressure).
the correct amount of coffee.
NotE
When using a finer espresso grind for
the Single Wall Filter basket, you will
need to increase the grind amount to
ensure the filter is correctly dosed.
NotE
Pressing the 1 CUP or 2 CUP buttons
during a programmed espresso will
immediately stop the extraction.
Download from Www.Somanuals.com. All Manuals Search And Download.
12
13
oPERAtING yoUR BREvILLE PRodUCt
oPERAtING yoUR BREvILLE PRodUCt
•
A beep will sound to indicate that
the temperature settings can now be
changed.
AdvANCEd tEMPERAtURE
SEttING
The water temperature can be increased or
decreased by 1°C or 2°C if desired.
Coffee of different origins or roast profiles
may need a different espresso brew water
temperature to optimise their flavour. If your
espresso is tasting slightly “ashy” decrease
the brew water temperature by 1°C. If your
espresso is tasting slightly “sour” increase
your brew water temperature by 1°C.
MANUAL SHot voLUME
ESPRESSo PRESSURE GAUGE
LoW PRESSURE PRE-INFUSIoN
Manually control low pressure
pre-infusion time and shot volume without
re-programming the pre-set shot volume.
The gauge needle will be positioned in
the pre-infusion zone at the start of the
extraction indicating the machine is in
low pressure pre-infusion mode.
The low pressure pre-infusion gradually
increases water pressure to gently expand
grinds for an even extraction before
increasing to full pressure.
•
•
The LED of the last saved setting will be
illuminated. See table on left.
•
Press and hold the 1 CUP or 2 CUP
button. The extraction will enter low
pressure pre-infusion until the button is
released
Pressing the 2 cup button to allows you
to toggle between the different settings.
•
•
When the 1 CUP or 2 CUP button is
released, extraction will continue at full
pressure.
Press the 1 CUP or 2 CUP button again
once the desired volume of espresso has
been extracted
•
Please note that if the 2 cup button is not
pressed within 10 seconds, the machine
will return to STANDBy mode and the
above steps will have to be repeated
MANUAL ESPRESSo
Press and hold the 1 CUP or 2 CUP button.
Release the button once sufficient espresso
has been extracted into the cup.
•
•
After you have made a selection, 2 beeps
will sound to indicate that your setting
has been saved.
IdEAL ESPRESSo ZoNE
During extraction, the gauge needle when
positioned in the middle zone, indicates
the espresso will be extracted at the ideal
pressure.
The machine will then return to
STANDBy mode.
OR
RESEttING dEFAULt voLUMES
To reset the machine to the default 1 CUP
and 2 CUP shot volumes, press and hold the
PROGRAM button until the machine beeps
three times. Release the PROGRAM button.
The machine will return to its original
default setting.
NotE
To amend temperature settings:
For optimal flavour when using a
1 CUP filter, you should extract approx.
30ml. When using a 2 cup filter, you
should extract approx. 60ml.
•
With the machine OFF, press and
hold the 1 cup button and then
simultaneously press and hold the power
button.
NotE
Default settings: 1 CUP shot volume is
approx. 30ml. 2 CUP is approx. 60ml.
WARNING
The metal parts of the portafilter will
be very hot.
POWER
Download from Www.Somanuals.com. All Manuals Search And Download.
14
15
oPERAtING yoUR BREvILLE PRodUCt
oPERAtING yoUR BREvILLE PRodUCt
UNdER ExtRACtEd ZoNE
tExtURING MILk
AUto PURGE
NotE
During extraction, the gauge needle when
positioned in the lower zone, indicates
the espresso has been extracted with
insufficient pressure.
The Infuser™ comes with a commercial style
steam wand.
For extracting espresso immediately after
using the steam function, this machine
features an auto-purge function.
The auto purge function ensures the
ground coffee will not be burnt by the
initial water flow from the thermocoil being
too hot. The water is automatically released
internally into the drip tray ensuring that
the thermocoil is at optimal temperature
for extracting espresso
After 5 minutes of continuous
steaming, the machine will
automatically disable the steam
function. The STEAM/HOTWATER
light will flash. When this occurs
return the steam dial to the STANDBY
position.
tExtURING MILk
•
Turn the STEAM/HOT WATER
selector dial to the steam position.
The STEAM/HOT WATER light will
flash to indicate the machine is heating
to create steam.
Hot WAtER
your espresso will always be extracted at
the optimal temperature ensuring only the
best flavours are extracted.
This occurs when the water flow through
the ground coffee is too fast and results in
an under extracted espresso that is watery
and lacks crema and flavour.
Causes for under extraction include the grind
being too coarse and/or insufficient coffee in
filter and/or under tamping.
•
•
When the STEAM/HOT WATER light
stops flashing the steam wand is ready
for use.
Before inserting the steam wand into
the milk, pause the steam by returning
the dial back to the STANDBy position.
This will avoid the milk splashing out of
the jug (this pause function lasts for 6
seconds before exiting steam mode).
•
•
Turn the STEAM/HOT WATER selector
dial to the Hot Water position.
ovER ExtRACtEd ZoNE
To stop the hot water, return the
STEAM/HOT WATER dial to the
STANDBy position.
The gauge needle, when positioned in the
upper zone during extraction, indicates the
espresso has been extracted with too much
pressure.
•
•
Insert the wand into the milk and return
the dial back to the steam position to
texture milk.
To stop the steam return the Steam dial
to the STANDBy position and remove
the jug.
NotE
This occurs when the water flow through the
ground coffee is too slow and results in an
over extracted espresso that is very dark and
bitter with a mottled and uneven crema.
When the espresso machine creates
steam, a pumping noise can be heard.
This is the normal operation of the
15 bar Italian pump.
Causes for over extraction include the grind
being too fine and/or too much ground
coffee in filter and/or over tamping.
Download from Www.Somanuals.com. All Manuals Search And Download.
16
17
CoFFEE MAkING tIPS & PREPARAtIoN
PRE-HEAtING
dUAL WALL CREMA
SyStEM FILtERS
CoFFEE MAkING tIPS
& PREPARAtIoN
Heating your cup or glass
The Dual Wall filters (1 & 2 CUP) are
designed to be used with pre-ground coffee
and regulate the pressure to help optimise
extraction regardless of the grind, dose or
tamp pressure.
A warm cup will help maintain the coffee’s
optimal temperature. Preheat your cup by
rinsing with hot water and place on the cup
warming tray.
Heating the portafilter and filter basket
A cold portafilter and filter basket can
reduce the extraction temperature enough
to significantly affect the quality of your
espresso. Ensure the portafilter and filter
basket are preheated with hot water before
initial use.
NotE
Wipe the filter and portafilter dry
before dosing with ground coffee as
moisture can encourage ‘channeling’
where water by-passes the ground
coffee during extraction.
The Dual Wall filters have DUAL WALL
stamped on the underside of the filter.
tHE GRINd
If grinding coffee beans, the grind size
should be fine but not too fine. The grind
size will affect the rate at which the water
flows through the ground coffee in the filter
basket and the taste of the espresso.
If the grind is too fine (looks like powder
and feels like flour when rubbed between
fingers), the water will not flow through the
coffee when under pressure. The resulting
espresso will be OVER EXTRACTED, dark
in colour and bitter in flavour
SINGLE WALL FILtERS
The Single Wall filters (1 & 2 CUP) are
designed to be used with freshly ground
coffee and allow you to experiment with
grind, dose, and tamp to create a more
balanced espresso.
If the grind is too coarse the water will
flow through the ground coffee in the filter
basket too quickly. The resulting espresso
will be UNDER EXTRACTED lacking in
colour and flavour.
The Single Wall filters have no markings on
the underside of the filter.
Download from Www.Somanuals.com. All Manuals Search And Download.
19
CoFFEE MAkING tIPS & PREPARAtIoN
CoFFEE doSE ANd tAMPING tRIMMING tHE doSE
CoFFEE MAkING tIPS & PREPARAtIoN
PURGING tHE GRoUP HEAd tExtURING MILk
The Razor™ precision dose trimming tool
allows you to trim the puck to the right level
for a consistent extraction.
There are two phases to texturing milk. The
first is stretching the milk to aerate it and
the second is swirling the milk to make it
silky smooth. These two operations should
blend into one.
•
Before placing the portafilter into the
group head, run a short flow of water
through the group head by pressing
the 1 CUP or 2 CUP button. This
will purge any ground coffee residue
from the group head and stabilise the
temperature prior to extraction.
•
•
Wipe coffee basket with a dry cloth.
If using Single Wall filter baskets,
grind enough coffee to fill the coffee
basket. you may need to experiment
with the amount of coffee to achieve
the correct dose.
•
•
Always start with fresh cold milk.
™
the Razor
Precision dose trimming tool
Fill the jug just below the V at the
bottom of the spout.
•
•
Tap the portafilter several times to
distribute the coffee evenly in the
filter basket.
INSERtING tHE PoRtAFILtER
•
•
•
Position the steam tip over the drip tray
and turn on the steam system, purging
any condensed water.
Place the portafilter underneath the group
head so that the handle is aligned with
the INSERT position. Insert the portafilter
into the group head and rotate the handle
towards the centre until resistance is felt.
Tamp down firmly (using approx.
15-20kgs of pressure). The amount
of pressure is not as important as
consistent pressure every time.
Insert the Razor™ into the coffee basket
until the shoulders of the tool rest on the
rim of the filter basket. The blade of the
dosing tool should penetrate the surface
of the tamped coffee.
Rotate the Razor™ dosing tool back and forth
while holding the portafilter on an angle over
the knock box to trim off excess coffee.
Turn the steam dial to the STANDBy
position, insert steam wand tip into milk
and turn dial back to STEAM position.
Insert the steam tip 1-2cm below
the surface of the milk close to the
right hand side of the jug at the
3 o’clock position.
ExtRACtING ESPRESSo
•
Place pre-warmed cup(s) beneath the
portafilter and press the 1 CUP or
2 CUP button for the required volume.
As a guide, the espresso will start
to flow after 8-10 seconds (infusion
time) and should be the consistency
of dripping honey.
•
Keep the tip just under the surface of the
milk until the milk is spinning clockwise,
producing a vortex (whirlpool effect).
•
•
•
If the espresso starts to flow before
6 seconds you have either under dosed
the filter basket and/or the grind is too
coarse. This is an UNDER-EXTRACTED
shot.
If the espresso starts to drip but doesn’t
flow after 15 seconds, then you have
either over dosed the filter basket
and/or the grind is too fine. This is an
OVER-EXTRACTED shot.
•
As a guide to dose, the top edge of the
metal cap on the tamper should be level
with the top of the filter basket AFTER the
coffee has been tamped.
Wipe excess coffee from the rim of the
filter basket to ensure a proper seal in
the group head is achieved.
•
your coffee filter basket is now dosed with
the correct amount of coffee.
A great espresso is about achieving the
perfect balance between sweetness, acidity
and bitterness.
The flavour of your coffee will depend on
many factors, such as the type of coffee
beans, degree of roast, freshness, coarseness
or fineness of the grind, dose of ground
coffee, and tamping pressure.
•
With the milk spinning, slowly lower the
jug. This will bring the steam tip to the
surface of the milk & start to introduce
air into the milk. you may have to gently
break the surface of the milk with the tip
to get the milk spinning fast enough.
ExtRACtIoN GUIdE
GRIND
DOSE
TAMP
SHOT TIME
OVER EXTRACTED
BITTER • ASTRINGENT
TOO MUCH
TOO FINE
15-20KG
OVER 40 SEC
USE RAZOR TO TRIM
•
•
Keep the tip at or slightly below the
surface, continuing to maintain the
vortex. Texture the milk until sufficient
volume is obtained.
8-10G (1 CUP)
15-18G (2 CUP)
BALANCED
OPTIMUM
15-20KG
25-35 SEC
Experiment by adjusting these factors
just one at a time to achieve the taste
of your preference.
Lower the tip beneath the surface, but
keep the vortex of milk spinning. The
milk is at the correct temperature
TOO LITTLE
UNDER EXTRACTED
UNDERDEVELOPED • SOUR
TOO COARSE
15-20KG
UNDER 20 SEC
INCREASE DOSE &
USE RAZOR TO TRIM
(60-65°C) when the jug is hot to touch.
Download from Www.Somanuals.com. All Manuals Search And Download.
20
21
CoFFEE MAkING tIPS & PREPARAtIoN
•
•
Move the steam dial to the STANDBy
position before taking the tip out of
the milk.
CARE & CLEANING
Set the jug to one side, turn steam on
to purge out any residual milk from the
steam wand and wipe steam wand with
a damp cloth.
•
•
Tap the jug on the bench to collapse
any bubbles.
Swirl the jug to polish and re-integrate
the texture.
•
•
Pour milk directly into the espresso.
The key is to work quickly, before the
milk begins to separate.
HINtS & tIPS
1. Use freshly roasted coffee beans,
with a ‘roasted on’ date and use
within 2 weeks of ‘roasted on’ date.
2. Grind beans immediately before
brewing as ground coffee quickly
loses its flavour and aroma.
3. Store coffee beans in a cool,
dark and dry container. Vacuum
seal if possible.
4. Buy coffee beans in small batches
to reduce the storage time and store
no more than one weeks supply at
any time.
Download from Www.Somanuals.com. All Manuals Search And Download.
22
CARE &CLEANING
CARE &CLEANING
INStALLING/REPLACING tHE
FILtER IN tHE WAtER tANk
CLEANING CyCLE
The espresso machine features an in-built cleaning cycle which should be carried out
periodically. The CLEAN ME light will automatically illuminate to indicate when a cleaning
cycle is required.
1
2
3
4
5
6
1
2
3
4
5
6
INSERT
LOCK
REPLACEMENT DUE
Set date 2 months ahead
Soak the water filter for
5 minutes
Rinse filter & mesh
Assemble
Install filter in water tank
Insert & lock water tank
CLEAN ME
POWER
Cleaning required
Empty drip tray and fill
water tank
Insert cleaning disc & filter Place tablet on top
basket into portafilter
Insert & lock portafilter
into Group Head
Turn machine off
The water filter provided helps to prevent
scale build up which over time can affect the
performance of your machine, potentially
causing blockages and heating, problems
Replacing the water filter every two months
will reduce the need to de-scale the machine.
If you live in a hard water area, we
recommend you change the water filter
more frequently.
PoRtAFILtER CLEANING
7
8
9
10
11
12
AUSTRALIA
1300 139 798
NEW ZEALAND
0800 273 845
INSERT
LOCK
Periodically run water through the machine
with the portafilter in place, but without
any ground coffee, to rinse out any residual
coffee particles.
HOLD TOGETHER 3 SEC
POWER
INSERT
LOCK
?
?
5 MIN
While pressing the POWER button down, press & hold
the 1 CUP & 2 CUP buttons
Wait 5 minutes to finish
Rinse the filter basket &
portafilter before use
No espresso extraction?
See Trouble Shooting Guide Call Service Centre for
cleaning tablets
Page 33.
5. Turn the machine OFF.
CLEANING CyCLE PRoCESS GUIdE
Replacing the Water Filter
•
•
•
Remove the filter from the plastic bag,
and soak in a cup of water for 5 minutes
Rinse the filter under cold running water
for 5 seconds
Wash the stainless steel mesh in the
plastic filter compartment with water
and assemble
6. Simultaneously press and hold the
1 CUP, 2 CUP and POWER button
for 3 seconds.
If cleaning is required, simply follow the
steps below and refer to the Machine
Cleaning Cycle guide.
7. The cleaning cycle will commence
and last for approximately 5 minutes.
Once complete, 3 beeps will sound.
Remove the portafilter and ensure
the tablet has completely dissolved.
1. Insert the cleaning disc into the one
or two cup filter basket.
2. Place the filter basket into
the portafilter.
•
•
Set the date dial 2 months ahead
To install, push down to lock into place
3. Put 1 cleaning tablet into the filter.
If the tablet has not dissolved, repeat steps
5 to 7 until tablet has dissolved.
4. Lock the portafilter into the
The water filter can be removed
from the water tank during operation if
not required.
group head.
NotE
For replacement water filters contact
Breville Customer Service Centre on
1300 139 798 (Australia) or
0800 273 845 (New Zealand).
Download from Www.Somanuals.com. All Manuals Search And Download.
24
25
CARE &CLEANING
dECALCIFyING
CARE &CLEANING
CLEANING tHE StEAM WANd
dECALCIFyING tHE MACHINE
After regular use, hard water can cause
mineral build up in and on many of the
inner functioning components, reducing
the brewing flow, power of the machine,
and affecting the quality of coffee.
We advise decalcifying the machine on a
regular basis (every 2-3 months) using a
mixture of white vinegar and water.
•
Remove the portafilter. Pour the mixture
of white vinegar and water into the
water tank.
Plug the machine into the power outlet
and switch On.
Press the POWER button to the
On position.
Place a large container under the
group head and steam wand.
When the brewing temperature has
been reached all the button surrounds
on the control panel will illuminate.
Press and hold the 1 CUP or 2 CUP
button to commence manual pour.
Release the button once half the mixture
of white vinegar and water has run
through the group head.
Set the STEAM/HOT WATER dial to
the STEAM position and allow steam
to run through the Steam Wand for
approximately 2 minutes. Return the
steam dial back to the STANDBy position.
1
2
3
4
5
•
•
•
•
Run steam to clear milk
from wand after texturing
Wipe steam wand after
each use
Clean hole with pin
Remove tip
Soak tip overnight then
re-attach
Follow the instructions provided, or use
the following as a guide:
•
•
The steam wand should always be
cleaned after texturing milk.
•
•
If the steam wand remains blocked,
use the pin on the cleaning tool to clear
the opening.
If the steam wand continues to be
blocked, the tip of the steam wand can
be removed by using the spanner in the
middle of the cleaning tool.
Wipe the steam wand with a damp cloth,
and then with the steam wand directed
back into the drip tray, briefly set the
steam dial to the STEAM position. This
will clear any remaining milk from
inside the steam wand.
Ensure the steam dial is in the STANDBy
position. Press the POWER button to Off
and allow the machine to cool.
SoLUtIoN FoR dECALCIFyING
diluted Solution (for softer water)
•
•
1 part white vinegar
2 parts cold tap water
•
•
Unscrew the tip with the cleaning tool.
•
Soak the tip in hot water before using
the pin on the cleaning tool to unblock.
Replace the tip back onto the steam
wand and secure with the cleaning tool.
•
•
Concentrated Solution (for harder water)
•
•
1 part white vinegar
1 part cold tap water
After decalcifying, remove the water
tank and rinse thoroughly then refill
with fresh cold water. To rinse the
machine, repeat previous steps.
WARNING
Do not immerse power cord, power
plug or appliance in water or any other
liquid. The water tank should never be
removed or completely emptied during
decalcifying.
Download from Www.Somanuals.com. All Manuals Search And Download.
26
27
CARE &CLEANING
CLEANING / UNBLoCkING tHE FILtERS, PoRtAFILtER ANd GRoUP HEAd
Periodically run water through the machine with the portafilter in place, but without any
ground coffee, to rinse out any residual coffee particles.
tRoUBLESHootING
1
2
3
4
5
6
INSERT
LOCK
PRESS & HOLD
Knock grinds out
Clean filter basket
Place filter basket into
portafilter
Insert & lock portafilter
into Group Head
Flush water
Use cleaning tool to unblock
Repeat steps C1-C2
Should the fine holes in the filters become
blocked follow the following steps:
Remove grill and EMPTy ME! indicator
from the drip tray. Wash the drip tray with
warm soapy water, using a non-abrasive
washing liquid, rinse and dry thoroughly.
The EMPTy ME! indicator can be removed
from the drip tray by pulling upwards to
release the side latches.
1. Place the filter into the portafilter. Run
water through the machine with the
filter and portafilter, without any ground
coffee, in place.
2. The fine pin on the cleaning tool can
The drip tray base and cover are
dishwasher safe.
be used to clear the filter basket holes.
3. To clean the Single Wall filters simply
run water through the portafilter
using the manual pour function by
holding down the 1 CUP button.
CLEANING tHE StoRAGE tRAy
The storage tray can be removed after the
drip tray is removed then cleaned with
a soft, damp cloth (do not use abrasive
cleansers, pads or cloths which can scratch
the surface).
4. For a thorough clean of the filters,
run a cleaning cycle of the machine
with the portafilter and filter in place
StoRING yoUR MACHINE
CLEANING tHE oUtER HoUSING /
CUP WARMING PLAtE
Before storing, press the POWER button to
off, turn the STEAM/HOT WATER dial to
STANDBy switch Off at the power outlet
and unplug.
Insert all accessories into position or into
the storage tray.
The outer housing and tray warming plate
can be cleaned with a soft, damp cloth. Then
polish with a soft, dry cloth.
Do not use abrasive cleansers, pads or cloths
which can scratch the surface.
Store upright. Do not place anything on top.
CLEANING tHE dRIP tRAy
WARNING
The drip tray should be removed, emptied
and cleaned at regular intervals, particularly
when the drip tray full indicator is showing
EMPTy ME!.
Do not immerse power cord, power
plug or appliance in water or any
other liquid. The water tank should
never be removed or completely
emptied during decalcifying.
Download from Www.Somanuals.com. All Manuals Search And Download.
28
tRoUBLESHootING
PRoBLEM
tRoUBLESHootING
PoSSIBLE CAUSES
WHAt to do
PRoBLEM
PoSSIBLE CAUSES
WHAt to do
When the machine is
switched on, the StEAM/
Hot WAtER lights is
flashing.
•
STEAM/HOT WATER
dial is not in STANDBy
position
Turn the STEAM/
Coffee is too cold
•
Cups not preheated
Preheat cups. Refer to
‘Pre-heating Cup or Glass’
on page 18.
HOT WATER dial to
‘STANDBy’ position.
Machine will commence
normal heat up procedure.
•
Milk not heated enough
(if making a cappuccino
or latté)
When the base of the jug
becomes too hot to touch
this is when the milk
is heated at the correct
temperature. Refer to
‘Texturing Milk’, page 20.
Coffee does not run
through
•
Machine is not turned
On or plugged in
Ensure the machine is
plugged in, switched On at
the power outlet and
the POWER button is
pressed On.
No crema
•
•
Coffee is not tamped
firmly enough
Refer to ‘Coffee Dose and
Tamping’, page 19.
•
•
Water tank is empty
Refer to ‘Filling The Water
Tank’, page 12.
Coffee grind is too
coarse
Ensure you use a suitable
espresso grind. Refer to
‘The Grind’ on page 18.
Coffee grind is too fine
Ensure you use a suitable
espresso grind. Refer to
‘The Grind’ on page 18.
•
Ground coffee is not
fresh
Change old beans with
fresh roasted or pre-
ground. Ground coffee
should not be kept for
longer than a week.
•
•
•
Too much coffee in the
filter
Refer to ‘Coffee Dose &
Tamping’, page 12 and 19.
Coffee tamped too
firmly
Refer to ‘Coffee Dose and
Tamping’ on page 19.
•
•
Filter holes are blocked
Use the fine pin on the
cleaning tool to clear the
holes. Refer to ‘Cleaning
The Filters’, page 26.
The filter is blocked
Clean the filters. Refer to
‘Cleaning The Filters’,
page 26.
Machine is making
pulsing/pumping sound
while extracting coffee or
steaming milk
The machine is
carrying out the normal
operation of the 15 bar
pump
No action require as this is
the normal operation of
the machine.
Coffee runs out too
quickly
•
The coffee grind is too
coarse
Ensure you use a suitable
espresso grind. Refer to
‘The Grind’ on page 18.
•
•
Not enough ground
coffee in the filter
Refer to ‘Coffee Dose and
Tamping’, page 12 and 19.
Ground coffee not
tamped firmly enough
Refer to ‘Coffee Dose and
Tamping’, page 19 .
Download from Www.Somanuals.com. All Manuals Search And Download.
30
31
tRoUBLESHootING
PRoBLEM
tRoUBLESHootING
PoSSIBLE CAUSES
WHAt to do
PRoBLEM
PoSSIBLE CAUSES
WHAt to do
Coffee runs out around
the edge of the filter
holder
•
Filter holder is not
inserted in the group
head properly
Insert filter holder to
align into ‘LOCK’ position
in group head. Refer to
‘Inserting The Portafilter’,
page 19.
No steam is generated
•
Machine is not turned
On
Ensure the machine is
plugged in, switched On at
the power outlet and
the POWER button is
pressed On.
•
There are coffee
grounds around the
filter rim
Clean any excess ground
coffee from the rim of the
filter holder to ensure a
proper fit into the brew
head.
•
•
Water tank is empty
Refer to ‘Filling The Water
Tank’, page 12.
Steam Dial is not in
STEAM/HOT WATER
dial position
Turn the STEAM/HOT
WATER dial to the
STEAM position.
•
•
•
Too much ground coffee Refer to ‘Coffee Dose &
in the filter
Tamping’, page 12.
•
Steam Wand is blocked
Use the pin on the cleaning
tool to clear the opening. If
the steam wand continues
to be blocked remove the
tip of the steam wand using
the spanner in the middle
of the cleaning tool. Refer
to ‘Care and Cleaning’,
page 25.
Ground coffee has been
tamped too firmly
Refer to ‘Coffee Dose &
Tamping’, page 19.
Incorrect filter for
amount of ground
coffee used
Ensure you use the small
filter for 1 cup of coffee and
the larger filter for 2 cups
of coffee.
No hot water
•
•
Empty tank
Fill tank
Coffee extracts as drops
from the portafilter
•
The water tank is empty
or low
Refer to ‘Filling The Water
Tank’, page 12.
Milk is not creamy after
texturing
Not enough steam
Steam wand may be
blocked. Refer to ‘Care and
Cleaning’, page 25.
•
•
Coffee grind is too fine
Ensure you use a suitable
espresso grind. Refer to
‘The Grind’ on page 18.
Too much coffee in
basket
Use cold fresh milk. Refer
to ‘Texturing Milk’, page 15.
•
Machine is blocked by
mineral deposits
Decalcify the machine.
Refer to ‘Decalcifying’,
page 23.
Machine is not working
The safety thermal-cut may
have activated due to the
pump overheating.
Machine is making a loud
and continuous pumping
noise
•
•
Water tank is empty
Refer to ‘Filling The Water
Tank’, page 12 .
Turn the machine off and
allow to cool for about
30-60 minutes.
Water tank is not
securely in place
Refer to ‘Filling The Water
Tank’, page 12 .
Download from Www.Somanuals.com. All Manuals Search And Download.
32
33
CoFFEES to tRy
CAPPUCCINo
CoFFEES to tRy
A single shot of espresso with textured milk, garnished with
drinking chocolate.
ESPRESSo
Intense and aromatic, it is also known as an espresso or short
black and is served in a small cup or glass.
LAtté
A latté consists of a single espresso with textured milk and
approx. 10mm of foam.
MACCHIAto
Traditionally served short, the macchiato is also poured as a
long black with a dash of milk or a dollop of textured milk.
LoNG BLACk
Add hot water first, then a shot of espresso (single or double)
so that crema is maintained.
RIStREtto
A ristretto is an extremely short espresso of approximately
15ml, distinguished by its intense flavour and aftertaste.
Download from Www.Somanuals.com. All Manuals Search And Download.
35
|