Installation
Instructions
ADA Compliant HN200
Recess-Mounted
Shower with
• Equa Flo™
• Accu-Zone™ Infrared
Control
• Thermostatic Control
• Single Valve
• Air Metering Valve
• Touch-Time™ or
• Touch Time™ w/Battery
Table of Contents
HN200
(Valve Right/Seat Left shown,
Pre-Installation Information . . . . . . . . . . . . 2
HN200 Components . . . . . . . . . . . . . . . . . . .3
HN200 Shower Stall Dimensions . . . . . . . .3
Installation Instructions . . . . . . . . . . . . . . 4-7
Cleaning Instructions . . . . . . . . . . . . . . . . . .7
Shower Seat Repair Parts . . . . . . . . . . . . . . .8
Shower Curtain Repair Parts . . . . . . . . . . . .8
Valve Left/Seat Right is opposite)
36" x 36" enclosure is not
provided as standard equipment
IMPORTANT
Read the entire installation manual to ensure proper
installation of your HN200 shower.
This manual covers all of the HN200 variations and
options available, including shower seat and curtain
installation. Simply omit the steps which do not apply
to the unit you are installing.
Valve Left/Seat Right version is shown throughout
this manual. Valve Right/Seat Left is opposite.
Plumbing contractor shall be responsible for
installing shower face plate at the correct height to
meet accessibility requirements.
This installation manual and parts list should be filed
by the owner’s maintenance department.
P.O. Box 309, Menomonee Falls, Wi 53052-0309
TEL. 1-800-BRADLEY FAX (262) 251-5817
215-1189 Rev. F; EN 02-342
Page 1 of 8
Download from Www.Somanuals.com. All Manuals Search And Download.
ADA Compliant Recess-Mounted Shower
HN200
Installation Instructions
HN200 Components and Shower Stall Dimensions
Elbow with Flange
Showerhead
Inline Backflow
Preventer
Quick Disconnect
Stainless Steel Hose
Diverter Valve
Hand-Held Hose Spray
with Post-Style Bracket
Shower Valve
(Equa-Flo™ shown)
Recessed Soap Dish
Shower Face Plate Assembly
Grab Bar (S53-184)
18"
18"
(457mm)
(457mm)
36"
(914mm)
15"
15"
(381mm)
36"
(381mm)
(914mm)
14-1/4"
(362mm)
max.
14-1/4"
(362mm)
max.
36"
4"
(914mm)
4"
36"
(102mm)
(102mm)
min.
(914mm)
min.
VALVE LEFT/SEAT RIGHT
VALVE RIGHT/SEAT LEFT
NOTE: Compliance and conformity to local codes and ordinance is the responsibility of the installer.
Bradley Corporation • 215-1189 Rev. F; EN 02-342
3
Download from Www.Somanuals.com. All Manuals Search And Download.
ADA Compliant Recess-Mounted Shower
HN200
Installation Instructions
Installation Instructions
NOTE: Flush the supply lines before making connections.
NOTE: Install the supply inlets no lower than 48" and no higher than 60" off of finished floor.
Step 1: Rough in piping for shower
NOTE: When facing the wall, the supply pipe to the left of the centerline is HOT.
1. Rough in 1/2" NPT hot and cold water supply piping for valve at the dimension shown in Figure
1 (piping supplied by installer).
18"
(457mm)
FRONT OF
SHOWER
15"
BACK
WALL
2-1/2"
(64mm)
TYP.
(381mm)
WALL
OPENING
OUTLINE
7-1/2"
(191mm)
3-3/4"
(95mm)
2"
(51mm)
72"
(1829mm)
A.F.F.
45"
(1143mm)
2"
(51mm)
1/2" NPT
SUPPLIES
40"
(1015mm)
48"
(1219mm)
to 60"
(1524mm)
A.F.F.
48"
(1219mm)
A.F.F.
NOTE: Due to differing state codes, if the
valve height is different from the indicated
43" (1091 mm), all dimensions within the
symbol must be changed by the same amount.
C
L
20"
38-1/8"
(968mm)
A.F.F.
Example: If the code approved height is 40",
then 43" (1091mm) - 40" (1015mm) = 3"
(76mm). Result: Subtract 3" (76mm) from all
(508mm)
Figure 1
dimensions within the
symbol.
NOTE: WALL OPENING RECESS
TO BE 4" (102mm) DEEP
4
Bradley Corporation • 215-1189 Rev. F; EN 02-342
Download from Www.Somanuals.com. All Manuals Search And Download.
ADA Compliant Recess-Mounted Shower
HN200
Installation Instructions
Installation Instructions continued…
Step 2: Make plumbing connections
NOTE: Hoses need to be connected to 1/2" NPT pipe supply
before the shower is fastened to the wall.
1. Make water supply connections to the stainless steel hoses
(see Figure 2). Equa-Flo™ and Thermostatic= 1/2" NPT
Hot and Cold supplies. Single Valve, Accu-Zone™ Infrared
Control, Air Valve and Touch Time™ = 1/2" tempered
supply.
Step 3: Install face plate and grab bar
1. Position the face plate on the wall. Mark the wall and install
twelve wall anchors suitable for use with 1/4"-20 x 3/4"
button head Allen key screws (see Figure 3).
2. Attach the face plate to the wall with twelve 1/4"-20 x 3/4"
button head Allen key screws provided (see Figure 3).
3. Attach the grab bar to the wall.
• Position the “L” of the grab bar to fit the back wall of the
shower stall.
VALVE LEFT
SEAT RIGHT
4. Use the flange as a template and mark the six screw hole
locations and install six anchors supplied by installer for
1/4"-20 x 1-1/4" flat head Allen key
Figure 2
screws (see Figure 3).
5. Secure the grab bar to the six wall
anchors using six 1/4”-20 x 1-1/4"
flat head Allen key screws (provided
by installer) (see Figure 3).
1/4"-20 x 3/4"
BUTTON HEAD
ALLEN KEY SCREW
(12) PLACES
(160-143)
FACE PLATE
GRAB BAR
(S53-184)
NOTE: ALL WALL
ANCHORS SUPPLIED
BY INSTALLER.
1/4"-20 x 1-1/4"
FLAT HEAD ALLEN
KEY SCREW
Figure 3
VALVE LEFT - SEAT RIGHT
Bradley Corporation • 215-1189 Rev. F; EN 02-342
5
Download from Www.Somanuals.com. All Manuals Search And Download.
ADA Compliant Recess-Mounted Shower
HN200
Installation Instructions
Installation Instructions continued…
Step 4: Mount shower seat
NOTE: All anchoring devices (supplied by installer)
must be carefully selected to insure adequate support for
the shower seat, given the type of wall construction.
1. Measure and scribe a horizontal line 16-1/16" above
the finished floor (see Figure 4).
2. Position the folding shower seat against the wall
with the three mounting holes on the seat centered
on the scribed line.
• Using the mounting holes as a template, mark the
three mounting locations on the wall.
3. Install appropriate anchors (supplied by installer) for
1/4" sheet metal screws in the wall at the three
mounting locations.
Figure 4
4. Mount the shower seat to the wall with the
three 1/4" sheet metal screws (supplied) at
the anchored mounting locations.
Figure 5
• Position the seat support tube in the
support bracket as shown in Figure 5. The
tube should rest on the bottom of the front
plate.
NOTE: When seat is properly installed, it should
decline downward from back to front 2° to 3° for
water drainage.
5. Place the support bracket against the wall
and adjust the bracket vertically until the
shower seat is level in down position.
• Using the mounting holes on the support
bracket as a template, mark the four
mounting locations on the wall.
6. Install appropriate anchors (supplied by installer) for
1/4" sheet metal screws in the wall at the four
mounting locations.
7. Mount the support bracket to the wall with the four
1/4" sheet metal screws (supplied) at the anchored
mounting locations.
Step 5: Install curtain rod
Figure 6
1. Measure and cut the stainless steel curtain rod to fit
the shower stall opening.
2. Mount one shower rod flange 80" (2032mm) from the floor as close to the opening of shower stall as
possible with two #10-13 x 2" Phillips-head screws provided (see Figure 6).
• Insert one end of the shower rod into the flange.
• Slide the other shower rod flange onto the shower rod.
3. Position the shower rod and flange at the same dimensions as the first flange but on the opposite side
of the shower stall opening.
4. Secure the flange to the wall with two #10-13 x 2" Phillips-head screws provided.
5. Install the ten hooks onto the curtain rod and hang the curtain onto the rod.
6
Bradley Corporation • 215-1189 Rev. F; EN 02-342
Download from Www.Somanuals.com. All Manuals Search And Download.
ADA Compliant Recess-Mounted Shower
HN200
Installation Instructions
Cleaning and Maintenance Instructions for Stainless Steel
Material Description: Stainless steel is extremely durable, and maintenance is simple and inexpensive.
Proper care, particularly under corrosive conditions, is essential. Always start with the simplest solution and
work your way toward the more complicated.
Routine cleaning: Daily or as often as needed use a solution of warm water and soap, detergent, or ammonia.
Apply the cleaning solution per the manufactures instructions and always use a soft cloth or sponge to avoid
damaging the finish.
Stubborn Stains: To remove stains from stainless steel use a stainless steel cleaner and polish such as Ball®
stainless steel cleaner or a soft abrasive. Always follow the manufactures instructions and apply in the same
direction as the polish lines.
IMPORTANT: NEVER USE ORDINARY STEEL WOOL OR STEEL BRUSHES ON
STAINLESS STEEL. ALWAYS USE STAINLESS STEEL WOOL OR
STAINLESS STEEL BRUSHES.
Special Situations for Material
Fingerprints and Smears: To remove fingerprints or smears use a high quality stainless steel cleaner and
polish in accordance with the manufactures instructions. Many of these products leave a protective coating
the helps prevent future smears and fingerprints.
Grease and Oil : To remove grease and oil use a quality commercial detergent or caustic cleaner. Apply in
accordance to the manufactures instructions and in the direction of the polish lines.
Precautions: Avoid prolonged contact with chlorides (bleaches, salts), bromides (sanitizing agents),
thiocyanates (pesticides, photography chemicals, and some foods), and iodides on stainless steel equipment,
especially if acid conditions exist.
IMPORTANT: DO NOT PERMIT SALTY SOLUTIONS TO EVAPORATE AND DRY ON
STAINLESS STEEL.
The appearance of rust streaks on stainless steel leads to the belief that the stainless steel is rusting. Look for the
actual source of the rust in some iron or steel particles which may be touching, but not actually a part of the
stainless steel structure.
NOTE: Strongly acidic or caustic cleaners may attack the steel causing a reddish film to appear. The use of
these cleaners should be avoided.
Brand Names: Use of brand names is intended only to indicate a type of cleaner. This does not constitute an
endorsement, nor does the omission of any brand name cleaner imply its inadequacy. Many products named are
regional in distribution, and can be found in local supermarkets, department and hardware stores, or through your
cleaning service. It is emphasized that all products should be used in strict accordance with package instructions.
Bradley Corporation • 215-1189 Rev. F; EN 02-342
7
Download from Www.Somanuals.com. All Manuals Search And Download.
ADA Compliant Recess-Mounted Shower
HN200
Installation Instructions
Shower Seat Repair Parts
158-010 Left Hand Plastic Seat (Valve Right)
158-011 Right Hand Plastic Seat (Valve Left)
Shower Curtain Repair Parts
Curtain Pre-pack S30-068
ITEM
PART NO.
DESCRIPTION
QUANTITY
1
170-006
170-006D
170-006E
151-001
269-367
150-157
P10-412
Vinyl Shower Curtain
Duck Shower Curtain
Herculite Shower Curtain
Curtain Hook
1
2
3
4
5
10
Curtain Rod
1
Shower Rod Flange
#10-13 x 2” Phillips-Head Screw
2
1 Bag (4 Screws)
8
Bradley Corporation • 215-1189 Rev. F; EN 02-342
Download from Www.Somanuals.com. All Manuals Search And Download.
|