User’s Manual
BV9982U
IN-DASH DVD/MP3/CD AM/FM
RECEIVER WITH MOTORIZED
FLIP-OUT 7" (178mm)
WIDESCREEN TOUCHSCREEN
DIGITAL TFT MONITOR
WITH DUAL (FRONT AND REAR) USB PORTS,
SD MEMORY CARD PORT AND
FRONT PANEL AV INPUT
BV9982U
IN-DASH DVD/MP3/CD AM/FM RECEIVER
WITH MOTORIZED FLIP-OUT 7" (178mm)
WIDESCREEN TOUCHSCREEN
DIGITAL TFT MONITOR
WITH DUAL (FRONT AND REAR) USB PORTS, SD MEMORY CARD
PORT AND FRONT PANEL AV INPUT
09.2011
BOSS Audio Systems
3451 Lunar Court • Oxnard, CA 93030
iPod® is a trademark of Apple, Inc.
registered in the U.S. and other countries.
Boss Audio Systems is not affiliated with Apple, Inc.
800.999.1236
Download from Www.Somanuals.com. All Manuals Search And Download.
PRECAUTION
WARNING: TO REDUCE THE
RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE
THIS APPLIANCE TO RAIN OR
MOISTURE.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
!
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral triangle, is
intended to alert the user to the presence of uninsulated dangerous voltage
within the products enclosure that may be of sufficient magnitude to constitute
a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert user to
the presence of important operating and maintenance (servicing) instructions
in the literature accompanying the appliance.
!
CLASS 1 LASER PRODUCT
Laser product symbol: located on the rear panel of the unit, indicate this player is a class
laser product, only use weak laser and no hazardous radiation outside of the unit.
1.Read through this instruction manual before installation and use.
2.Do not touch the power plug with wet hand.
3.Switch off the main power when the unit is not in use. (Disconnect the power plug from
the power outlet when you do not intend to use the unit for a prolonged period of time.)
Before moving the unit, remove the disc from the unit/ tray first.
4.Do not open the cover or touch any of the components exposed out of the unit, only for
qualified technicians.
5.Do not expose the unit under direct sunlight or nearby objects that radiate heat to avoid
damage the unit.
6.Do not place the unit in moist and humid conditions, which effect the pick-up of the unit
lead to out of work.
7.Place the unit on a flat surface and ventilative condition. Please ensure the ventilation
holes are not covered to avoid overheating and malfunction.
8.Clear the panel and case with soft dry cloth only, do not apply any kind of thinner,
alcohol or sprays.
9.The apparatus shall not be exposed to dripping or splashing and that no objects filled
with liquids, such as vases, shall be placed on the apparatus .
Contents
1. Before Operation...........................................................................................3
1.1 Glossary................................................................................................ 3
1.2 Precautions..................................................................................... .......3
1.3 Maintenance and Cleaning of Discs..........................................................4
1.4 Battery Information of the Remote Control.................................................4
1.5 Remote Control Description.....................................................................5
1.6 Locations and Names of Controls on or in the Unit......................................6
1.7 Wires Connection Description..................................................................7
1.8 Unit Installation.......................................................................................8
2. Common Operation........................................................................................9
3. Radio Operation...........................................................................................10
4. Disc, USB and MMC/SD Card Operation........................................................12
4.1 Load/unload Disc, USB or Card...............................................................12
4.2 Pause Playback.....................................................................................14
4.3 Stop Playback .......................................................................................14
4.4 Select Chapter/Track with the UP/DN or the >>|/|<< Buttons......................14
4.5 Select Chapter/Track with the Number Buttons.........................................14
4.6 Select Chapter/Track with the Root/PBC Menu.........................................14
4.7 Playback with Speed..............................................................................15
4.8 Playback with Slow Speed......................................................................15
4.9 Display Still Frame Step by Step.............................................................16
4.10 Playback Repeatedly...........................................................................16
4.10.1 One/All Repeat................................................................................16
4.10.2 A-B Repeat.......................................................................................16
4.11 Playback in Scan Mode.........................................................................17
4.12 Playback from a specified Chapter/Track or a Specified Time...................17
4.13 Playback in Random.............................................................................17
4.14 Playback in Different View-Angle...........................................................17
4.15 Playback in Zoom Mode........................................................................17
4.16 Change the Caption Language..............................................................18
4.17 Change the Audio Language.................................................................18
4.18 Look over the Playback Status..............................................................18
4.19 Program Playback...............................................................................19
4.20 Playback IMAGE files..........................................................................19
4.21 Playback MP4 files..............................................................................20
4.22 ESP and ID3 Function..........................................................................20
4.23 DVD System Menu Setup Operation......................................................20
*
*
Parental Control..................................................................................24
Region Code.......................................................................................25
5. Trouble Shooting.........................................................................................26
6. Specification...............................................................................................27
1. Before Operation
1.1 Glossary
PBC (playback control)
It is a kind of signal(menu) recorded in the disc with SVCD or VCD2.0
format used for the playback control. For the discs containing PBC, It can
playback interactive software with the menu displayed on monitor screen.
If the disc contain still images, it can playback high definition of still images.
Title
Generally, the title is the important part of DVD disc. for example, the
theme part of movie is title 1, the part described how to make movie is title
2, the cast is title 3, etc. Every title contain a serial number that is easy to
look up.
Chapter
A title can be divided into several blocks, so that every block can be operated
as a unit, the unit is called chapter. The chapter contain a unit at least.
Track
It is the biggest component of VCD. Generally, every song of the disc
is a track.
1.2 Precautions
Safety
1. Power Source: The unit should be connected to power supply only of
the type described in the operating instructions or as marked on the unit.
2. The unit is designed for negative terminal of the battery which is
connected to the vehicle metal. Please confirm it before installation.
3. Do not allow the speaker wires to be shorted together when the unit is
switched on. Otherwise it may overload or burn out the power amplifier.
4. Do not install the detachable panel before connecting the wire.
Environment
1. Do not use this unit near water and moisture.
2. If moisture forms inside the Lens, it may not operate properly. To correct
this problem, wait until the moisture is evaporated.
3. If the car interior is extremely hot, do not use the player until the car has
been cool off .
1.3 Maintenance and Cleaning of Discs
Disc Maintenance
6. Specification
1. To keep the disc clean, handle the disc by its edge, do not touch the disc
surface of the play side.
General Specification
2. Do not stick paper or tape on the disc. If there is anything on the disc surface,
wipe it up with a soft cloth before using.
3. Do not expose the disc to direct sunlight, or nearby heat sources such as
caliduct, or leave it in a car parked in direct sunlight where there can be a
considerable rise in temperature.
Power Supply Requirement..................................................DC 12V
Maximum Power Output............4 x 85W(measured at DC 14.4 V)
Dimensions(w x h x d).....................................7”W x 2”H x 6.3”D
4. Put the disc inside disc case to keep temperature after finishing playback.
DVD Deck Specification
Disc Cleaning
Format.....................................DVD/VCD/JPEG/MP4/MP3/WMA/CD
Video System........................................................................NTSC
Audio System..............................................................24 bit/96KHz
Loading System.......................................................... Auto Loading
Mounting Angle.................................................................0 to +/-30
1. Before playing, wipe the disc with a clean cloth. wipe the disc outwards from
the disc center.
2. Do not use petrol, thinner. Commercial cleaner or anti-static spray to wipe
disc.
Video Specification
+
side up
B
Video Type...................................................................16:9 and 4:3
Video Output level......................................Composite:1.0± 0.2Vp-p
Load impedance: 75 ohms
A
Fig.1
Fig.2
Fig.3
Horizontal Resolution................................................................500
Audio Specification
1.4 Battery Information of the Remote Control
Replace Battery in the Remote Control:
1.Before using the remote control for the first time, pull the insulating
sheet out of the remote control as the direction indicated by the
arrow.(see fig.1)
+0
Audio Output(Analog audio)..........................................2.0 -1.0Vrms
Frequency Response.............................20Hz ~ 20KHz(at 1KHz 0 dB)
S/N Ratio(Audio).............................................≥90dB(at 1KHz 0 dB)
Separation..............................................................................50dB
2.Press the movable block hold as the direction indicated by the A arrow
(See fig.2), then pull the battery holder out of the remote control as
the direction indicated by the B arrow(see fig.2).
3.Replace the old battery by a new battery with (+) polarity side upward.
(See fig.3).
4.Insert the battery holder to the original position in remote control.
(See fig.3).
Note about the Battery of the Remote Control:
1.Improper use of battery may cause overheating or explosion.
2.Battery leakage may cause damage to the remote control(Battery
Life: 6 months with normal use in normal room temperature).
3.Do not short the battery.
4.Do not throw the battery into the fire.
5.To avoid the risk of accident, keep the battery out of reach of children.
Radio Specification
FM Section
Frequency range.......................................87.5MHz - 107.9MHz(US)
87.5MHz - 108.0MHz(EU)
Usable sensitivity......................................................................3uV
I.F Frequency....................................................................10.7MHz
AM Section
Frequency....................................................530KHz - 1710KHz(US)
522KHz - 1620KHz(EU)
1.5 The Remote Control Description
5. Trouble Shooting
3
27
1
35
Please read the user’s manual carefully before using the DVD player. If you have any troubles
in using this player, try to solve the problems by the suggestions mentioned below. If you can
not remove the trouble after using all the suggestions, please contact the company or the
technical service center authorized by us. For the sake of your safety, please do not open the
cover and repair the player by yourself, if that, it may cause electric shock.
1. TILT BUTTON
2. MENU BUTTON
3. POWER BUTTON
4. ^ BUTTON
14
4
2
NO PICTURE, SOUND AND INDICATION
29
32
9
33
*
*
*
Ensure that the power switch is on.
Ensure that the power cord is not damaged or the fuse is not blown.
Ensure that the power plug is connected to the inlet tightly.
6
8
5. >>| BUTTON
34
13
31
NO SOUND BUT HAVE PICTURE
6. > BUTTON
5
*
*
*
*
*
Ensure that the player’s audio output has a good connection with amplifier’s audio input.
Check whether the audio connector is damaged.
Check whether you have turned down the volume.
Ensure that you have set the right AUDIO setup of the player.
7
7. |<< BUTTON
8. v BUTTON
10
30
40
11
12
Ensure that the audio is not under muted.
9. SEL BUTTON
10. PLAY/PAUSE BUTTON
NO PICTURE BUT HAVE SOUND
41
24
28
*
*
*
*
Ensure that the player’s video output has a good connection with monitor’s video input.
Ensure that you have turned your monitor to the AV input channel connecting to your player.
Check whether the video connector is damaged.
10+
16
15
18
17
11. NUMBER(0~10,+10
-10) BUTTONS
12. 10+/PTY BUTTON
Ensure that you have set the right VIDEO settings of the player.
21
22
BLACK AND WHITE PICTURE OR SCREEN ROLLING
Ensure that you have set the right TV SYSTEM (e.g. PAL, NTSC) setting.
*
26
25
23
36
37
13. SETUP BUTTON
14. MODE BUTTON
15. APS BUTTON
19
20
39
38
FLAWS OF PICTURE OR SOUND
*
*
*
*
Check whether the setting of AUDIO is right.
Check whether the disc is scratched or stained.
Check whether the AV connector and the output terminal is stained.
Check whether there is condensation inside the Lens. If so, leave the player off for an hour
or so, then try again.
29. MUTE BUTTON
30. STOP BUTTON
31. VOLUME- BUTTON
32. < BUTTON
16. SEARCH BUTTON
17. RDM BUTTON
*
Check whether the installation angle is less than 30°.
DISPLAY NO DISC OR BAD DISC
*
*
*
*
*
*
Ensure that you have put the disc in the unit.
Check whether the disc is put in the reverse side.
Check whether the disc is distorted.
Check whether the disc is stained or scratched badly.
Ensure that the disc format is compatible to the player.
Ensure that the temperature inside the car is not too high. If so, cool off till the ambient
temperature returns to normal.
18. RPT BUTTON
19. SUBTITLE BUTTON
20. TITLE/PBC BUTTON
21. ANGLE/ST BUTTON
22. ZOOM BUTTON
23. AUDIO BUTTON
24. CLK BUTTON
33. OK BUTTON
*
Replace another disc to insert it into the disc compartment.
34. VOLUME+ BUTTON
35. BAND BUTTON
36. PROG BUTTON
37. OSD BUTTON
38. LOUD BUTTON
39. STEP BUTTON
40. TA BUTTON
REMOTE CONTROL IS INSENSITIVE OR DOES NOT WORK
*
Check the batteries of remote control and make sure that they are powerful and have
good conductivity.
*
*
Direct the remote control to the IR sensor of the player.
Check whether there are some obstacles between the remote control and IR sensor.
SOME FUNCTION BUTTONS DO NOT WORK
*
*
*
Turn off the power, then turn on again.
Reset the unit to zero, then turn on again.
Remove the front panel from the unit, then install it again and then turn on again.
25. A-B BUTTON
26. INT BUTTON
THE RADIO DOES NOT WORK
Check whether the antenna cable is connected firmly. Or manually tune for a station.
27. EQ/OPEN BUTTON
*
28. LOC/SLOW-FWD BUTTON
41. AF BUTTON
1.6 The Locations and Names of Controls on or in the unit
19
18
23
5
22
3
20
1
4
*
Region Code
Q: Why does the unit display REGION ERROR after inserting disc into disc
compartment ?
A: Because the DVD player and disc has respective region code. If the region
codes of them do not match with each other, the DVD player can not play
the disc.
12
11 10
9
13
15
2
14
17
8
24
16
6
Front Panel
Appendix: The region code of DVD:
SD/MMC
The Motion Picture Association of America (MPAA) divided the world into
6 regions, and gave every region a code, namely region code. The region
codes and the countries or areas represented by the region codes as
follows:
7
21
The Front Facet after removing the front panel
Region 1: America, Canada, East-Pacific Inlands;
Region 2: Japan, West Europe, North Europe, Egypt, South Africa, Middle
East;
1. OPEN button
2. POWER/MUTE button
3. Monitor
4. AV IN socket
5. Disc Slot
13. INT/2 button
14. RPT/3 button
15. RDM/4 button
16. - 10 / 5 button
17. + 10 / 6 button
18. BAND button
19. APS button
20. EJECT button
21. RESET button
22. Small LCD Screen
23. IR Remote Sensor
24. REL button
Region 3: South-east Asian countries include Taiwan, Hong Kong, South
Korea, Thailand, indonesia, etc.;
Region 4: Australia, New Zealand, Central South America, South Pacific
Inlands;
6. USB Jack
7. SD/MMC Card Slot
8. MODE button
9. VOL knob
10. >>| button
11. |<< button
Region 5: Russia, Mongolia, Indian Peninsula, Middle Asia, East Europe,
North Korea, North Africa, North-west Asia etc.;
Region 6: China mainland.
12. PLAY/PAUSE/1 button
1.7 Wires Connection Description
The Description of the Wires Connection
* Parental Control
Wiring Connecting Socket 1
Fixing Screw Bolt
Q:Why after inserting DVD disc in the disc slot, a dialogue window appears that asks
to input a 4 digits password ?
A:This is because the movie you are playing is rated with the Parental Control, and
the current rating level of DVD player is lower than the current disc. You must change
the Parent Control setting to higher rating level.
GREEN
PARKING LINE
WHITE
Radio Antenna jack
Black
Wiring Connecting Socket 2
Black
Black
REVERSAL LINE
USB LINE IN
1. Parking wire must be connected. And the parking brake must be engaged in order for the monitor to work.
2. Use the clip end of the Ground Wire provided by manufacturer to connect Mounting Screw, using the other
end of the Ground Wire to connect the negative pole of the power source. Otherwise, the video on screen
maybe flashes.
! NOTE
The Description of the Wiring Diagram for Socket 1
* For the factory preset password of the DVD player, please refer to the relative
content of PASSWORD setup menu for details.
WIRING CONNECTING SOCKET 1
WIRING CONNECTING PLUG 1
ISO CONNECTOR
YELLOW
MEMORY B+
WOOFER LINE OUT
GREEN
FUSED
FILTER
BOX 1A
& 10 A
BLACK(GND)
RED
BLACK
RED R
WHITE
FUSES
IGNITION SWITCH
FRONT AUDIO RCA OUT
L
BLUE AUTO ANT
Parental Control
GRAY
WHITE
FRONT
FRONT
WHITE / BLACK
GREEN
GRAY / BLACK
VIOLET
RIGHT
SP
LEFT
SP
The Parental Control function of a DVD player can control the playback of movie
rated level in a disc. You can set the DVD player to be a certain rating level with
SETUP MENU on screen. If the rating level in the disc is higher than one set in the
DVD player, the DVD player can not playback the disc. The rating level setup can
be protected by the password. Therein, if you select Unlock item, the Parental
Control function will be invalid, and all level DVD rating will be played.
REAR
REAR
VIOLET / BLACK
GREEN / BLACK
NOTES:
1. Only speakers with 4 ohms impedance may be used.
2. Ensure that the blue auto antenna cable does not make contact
with any ground connection.
The Description of the Wiring Diagram for Socket 2
The disc movie can be designed as that the DVD player will playback the different
version of content of a same movie according to the different rating level set by
Parental Control. Depending on the DVD feature of seamless switching described
above, the scenes that are not fitting for children will be cleared or replaced by the
other fitting scene automatically.
WIRING CONNECTING SOCKET 2
WIRING CONNECTING PLUG 2
RED
R
BROWN
WHITE
YELLOW VIDEO
L
RED
R
GREY
REAR AUDIO RCA OUT
AV RCAAUX IN
YELLOW
WHITE
L
GREY
All rating levels of Parental Control are as follows:
VIDEO RCA OUT
BLACK
YELLOW
YELLOW
REAR VIEW CAMERA
Unlock
1
2
3
4
5
6
7
8
Kid Safe
G
PG
PG 13
PG R
R
NC 17
Adult
Description of Connecting the Parking Brake Line to the Parking Brake System Built in the Car
Parking brake
Parking brake wire(Green)
Parking brake switch
(inside the car)
To metallic body or chassis of the car
NOTE: after connecting the Parking Line, the video on the small monitor of the front panel will be display only after br aking the car.
HUE
It is for adjusting the hue of the video output.
SATURATION
It is for adjusting the saturation of the video output.
SHARPNESS
1.8 UNIT INSTALLATION
It is for adjusting the sharpness of the video output.
4.23.5 SPEAKER SETUP
INSTALLATION INSTRUCTIONS
THE UNIT IS INSTALLED TO BE AN ANTI-THEFT ONE. THE CHASSIS
OF THE UNIT WEARS A SLIDING METAL HOUSING. PLEASE DO THE
CONNECTION OF THE POWER, SPEAKERS AND ANTENNA ACCORDING
TO THE REQUIREMENT OF THE INSTRUCTION BOOK , THEN INSTALL
THE SLIDING METAL HOUSING IN THE CAR AS FOLLOWS.
TO BOOST UP THE CAPABILITY OF
ANTI-JAMMING, PLEASE FIX THE
METAL STRAP ON THE METAL
CONNECTED TO THE BOTTOM
BRACKET OF THE CAR.
METAL STRAP
SELECT THE PROPER TAB
FOR FIXING THE SLIDING
METAL HOUSING.
DOWNMIX
It is for selecting your desired sound effect when there is not central speaker
and sub-woofer. There are 3 mode: LT/RT, STEREO, VSS.
UNIT CHASSIS
LT/RT: When playing a disc with PRO LOGIC stereo effect, choose the item,
so it will output audio signal with vivid theatre effect.
STEREO: If you choose this item, when outputting audio signal with 5.1 channels,
it will output the left and right channels of signal ; when outputting audio signal
with 2 channels, it will output the common 2 channels of stereo signal.
VSS: If you choose this item, when playing a disc recorded with 5.1 channels,
the main channel speakers can output audio signal with VSS effect.
PLASTIC TRIM OUT
FRONT PANEL
DASH BOARD
SLIDING METAL HOUSING
TO DRAW THE CHASSIS OUT OF
THE SLIDING METAL HOUSING,
INSERT THE LEFT AND RIGHT KEY
PLATES INTO THE RIGHT POSITION
OF THE 2 SIDES OF CHASSIS.
4.23.6 DIGITAL SETUP
OP MODE
It is for selecting audio output mode
LINE OUT: It can compress the audio signal. So the volume level is lower.
RF REMOD: It can make the volume level higher.
DYNAMIC RANGE
After selecting the compression mode of LINE OUT, set the item, so you can
adjust the linear compression ratio. If you set it to be FULL, the Peak-to-Peak
value of the audio signal is the minimum; if you set it to be OFF, the Peak-to-
Peak value is the maximum.
DUAL MONO
It is for selecting a desired audio output mode for the left and right ways of signal.
It is mainly for Karaoke of Ac3. There are 4 modes in all as follows:
STEREO, MONO L, MONO R, MIX MONO.
2. Common Operation
4.23.2 LANGUAGE SETUP
1. To turn on/off the unit
In power off mode, short press any buttons except REL to turn on the unit.
In power on mode, long press the POWER button on the front panel or short
press the POWER button on the remote control to turn off the unit.
2. To slide the monitor of the Car Audio System out of the chassis
Shortly press the OPEN button on the front panel or long press the OPEN
button on the remote control can slide the monitor of the Car Audio System
out of the chassis or slide it into the chassis.
OSD LANGUAGE
This item is for selecting the language of the SYSTEM MENU and all operating
prompt interface displayed during playback.
AUDIO LANG
This item is for selecting a audio language.
SUBTITLE LANG
3. To select function mode
Press the MODE button to select RADIO, DISC
(After inserting a disc), USB(After inserting a USB
storage), SD/MMC CARD(After inserting a SD/
MMC card) or AUX mode.
This item is for selecting a subtitle language.
MENU LANG
This item is for selecting a disc menu language.
During playback, tapping the
icon after popping
up Keyboard interface can pop up Mode Menu as
right image. then tap one icon in it to select your
desired mode.
Mode Menu
4.23.3 AUDIO SETUP
Note: This unit has front and rear USB. Only one will work at a time.
4. To adjust sound level
Rotate the VOL knob on the front panel or press and hold the + or - button on the
remote control will adjust the volume level.
5. To mute sound
Press the MUTE button on the remote control to turn on/off MUTE mode.
Pressing the POWER button on the front panel shortly also can turn on/off MUTE
mode.
AUDIO OUT
There is only ANALOG mode, i.e. SPDIF/OFF, not optional.
KEY
It is for selecting your desired basic music tone(from low to high).
6. To display clock time
Press the CLK button to display clock time on the small monitor of the front panel.
After sliding the monitor into the chassis, pressing the CLK button can display
clock time on the small LCD.
4.23.4 VIDEO SETUP
7. To select a desired EQ mode
Press the EQ button on the remote control to select one of the preset music
equalizer curves: POP, ROCK, CLAS, FLAT. The sound effect will be changed.
8. To turn on/off LOUD mode
Press the LOUD button on the remote to turn on/off LOUD mode.
When turning on LOUD mode, it will enhance bass level immediately when bass
is not enough.
BRIGHTNESS
It is for adjusting the brightness of the video output.
CONTRAST
9. To reset the player
When the monitor , the small LCD display or some buttons are not working or
sound is distorted, press the REL button and detach the front panel from the
main unit, then press the RESET button to reset the program to factory default.
It is for adjusting the contrast of the video output.
11.To do setup
2. There are 6 setup pages in all for the System Menu. Press the > or < button to
select an desired setup page.
3. Press the ^ or v button to select an setup item in the selected setup page.
4. Press the > button to enter the setup item. Then press the v or ^ button to select
a desired mode of the setup item, finally press the OK button to confirm it.
To do setup, tap the
SETUP interface as right.
In the interface, select one of GENERAL, TIME, AUDIO,
VIDEO ,RADIO , CALIBRATE by tapping them, then set
them by tapping some icons on the right side accordingly.
icon in the Main Menu to turn to
*
*
Press the < button to return to the upper level.
Press the SETUP button again or use the direction buttons to highlight the item
of the EXIT SETUP and then press the OK button to exit the System Menu.
GENERAL SETUP
3. Radio Operation
For the DVD System Menu, there are 6 setup pages in all. They display as follows:
1. Enter RADIO mode
4.23.1 SYSTEM SETUP
When you use MODE button or Mode Menu to enter RADIO
mode, it will display RADIO interface as right.
TV TYPE
The setup item is for matching TV screen size.
4:3 PS: Choose the item when connecting a TV set
with 4:3 screen. When playing the pictures with
16:9 size, the left and right parts of the video will be
cut out, and display in full screen.
In RADIO interface, tapping the
Menu; during playback ,press and hold the mode button
can turn on or off TFT display; tapping the icon can
turn to frequency interface as right; the other icons are
same as ones in the unit panel or in the Remote Control.
icon can enter Mode
4:3 LB: Choose the item when connecting a TV set
with 4:3 screen. When playing the pictures with
16:9 size, the top and bottom parts of the TV screen
will be turned into a black square respectively.
16:9: Choose the item when connecting a TV set with 16:9 wide screen.
In menu set interface, you can adjust MUTE, APS, EQ,
TA, AF, PTY as right.
RADIO interface
2. BAND BUTTON
In RADIO mode, press the BAND button on the remote
control to select your desired radio band of FM1, FM2, FM3,
AM1 and AM2, and the word means which band is selected
will be displayed on the small monitor of the front panel.
PASSWORD
This setup item is for locking or unlocking the rating level of the Parental Control.
The defaulted state is locked. The defaulted password is 0000.
You can set a new password that you like: Select the PASSWORD item and then
press the > button to enter it, then input the original password 0000, and then
press the OK button to unlock it. Press the > button to enter it again, then input
a new password that you like and then press the OK button to make it effective.
Before the other persons see the Manual, you should get the password in mind
and cut out the part of PASSWORD in the Manual.
3. TUNE/SEEK UP/DOWN BUTTONS
In RADIO mode:
1) Press and hold the >>|/|<< button to automatically search
up/down for an available station from current frequency.
2) Briefly press the >>| / |<< button to manually search up or down with step by step for your
desired station from the current frequency.
AUDIO & VIDEO SETUP interface
4. APS BUTTON
RATING
In RADIO mode:
The item is for setting a new rating level of the Parental Control.
1. Select the PASSWORD item and then press the > button to enter it, then input
the password mentioned above, and then press the OK button to unlock the
setting of the rating level of the Parental Control.
2. Select the RATING item and then press the > button to enter it, then use the
direction buttons to select your desired rating level, then press the OK button
to confirm.
3. Select the PASSWORD item again and then press the > button to enter it, then
input the password, and then press the OK button to lock the new setting of
the rating level of the Parental Control.
1)When pressing and holding the APS button,the radio searches from the lowest frequency
and checks the signal strength level until 1 cycle search is finished. And then the 6 strongest
stations are preset to the corresponding preset number memory bank. The AS operation is
implemented in the each bank of the selected band. When the AS operation is finished, it
will scan each preset station for 5 seconds in FM or AM band from M1 as briefly pressing
APS button. After finishing a circle of scanning , it will resume broadcasting on the M1.
(It can store 3x6 stations for FM and 2x6 stations for AM in all)
2) When briefly pressing the APS button, the radio will scan each preset station for 5
seconds in FM or AM band from M1. After finishing a circle of scanning, it will resume
broadcasting on the M1.
NOTE: In FM band, FM1,FM2,FM3 is checked one at a time; In AM band, AM1, AM2 is
checked one at a time.
DEFAULT
This item is for making all setup items change back to original status.
5. PRESET STATION [ 1-6 ] BUTTONS
When you select the IMAGE file sort icon, press the ^ or > button to select the
first IMAGE file, then press the v button to select the desired IMAGE file, finally
press the OK or PLAY/PAUSE button to display the image in full screen from
the selected IMAGE file.
In RADIO mode:
1) To memorize the current frequency on the current band, press and hold any one
of the six preset buttons (1-6) on remote control or rotate number knob and long
press it .
3. During IMAGE playback, press one of the >/</^/v buttons to change the angle of
viewing picture that is displaying as follows:
2) To recall the preset memory on the current band, press one of the preset buttons
[1-6] on remote control or rotate number knob and press it .
>: 90 deg cw; <: 90deg ccw; ^:UP<-->DOWN; v: LEFT<-->RIGHT
During IMAGE playback, press the PROG button to change the mode of refresh
picture.
During IMAGE playback, press the STOP button to stop playing and return to the
root menu.
6. STEREO/MONO BUTTON
Press the ST button on the remote control to select the STEREO or MONO sound
mode for FM band.
7. LOC BUTTON
*
*
During IMAGE playback, the following buttons are not available: SLOW-FWD,
SUBTITLE, TITLE, ANGLE, AUDIO, RDM, INT and A-B.
In IMAGE mode, the other operations are same as ones in MP3/WMA mode.
1) In RADIO mode, when the signals of the distant radio stations are very weak and
the receiving effect is bad during tuning, check whether there is the word LOC on
LCD. If there is the word LOC on LCD, press this button to turn off the LOC
function, then tune again for the distance radio station;
2) In RADIO mode, when the signals of the local radio stations are too strong this
causes interference to the receiving effect during tuning, press this button to turn
on the LOC function to display the word LOC on LCD, then tune again for the local
radio station.
4.21 Playback MP4 files
1. The root menu is displayed on TV when beginning to switch on MP4 mode,
then it will automatically play the first file.
During playback, press the STOP button to stop playing and return to the
root menu.
8. PTY (PROGRAM TYPE) BUTTON
2. When displaying the root menu, press the direction buttons to select your
desired FOLDER ,file or file sort icon, then press the OK or PLAY button to
open the FOLDER, open the files of the file sort icon or play the selected file.
When displaying the root menu, you can also use the number buttons to
select the serial number of the file and play the file.
Press the PTY button briefly to select one of the following modes:
PTY MUSIC group- - PTY SPEECH group -- OFF
When PTY group is on, press the VOL+ or VOL- button on the remote control or
rotate the VOL knob on the front panel to select one of PTY programs as follows:
<-->NEWS<-->AFFAIRS<-->INFO<-->SPORT<-->EDUCATE<-->DRAMA
<-->CULTURE<-->SCIENCE<--> VARIED<-->WEATHER<--> FINANCE
<-->CHILDREN<-->SOCIAL<-->RELIGION<-->PHONE IN<-->TRAVEL
<-->LEISURE<-->DOCUMENT< -->PTY NONE<-->POP M< -->ROCK M
<-->EASY M<-->LIGHT M<--> CLASSICS<-->OTHER M<-->JAZZ
<-->COUNTRY<-->NATION M<-->OLDIES<-->FOLK M<-->
*
*
The ANGLE, PROG, RDM, INT and TITLE/PBC button are not valid.
The other functions are same as ones in DVD mode; but the RPT function is
same as one in MP3/WMA mode.
4.22 ESP and ID3 Function
When PTY group is on, pressing the 6 number buttons also can select one of PTY
programs as above.
There is ESP function for all formats of discs.
After selecting one of the PTY programs, it will display SEEK PTY and
automatically search for the station of the PTY program. If the station of the PTY
program does not exist, it will display PTY NONE and then return back to the
normal station.
In MP3/WMA mode, during playback, the information of the file name, folder
name, song s title, artist and album will be scrolling on the LCD display.
As long as the current playing MP3 music contains relevant ID3 tag information
in version 1.0/2.0 format, the 3 items underlined above will be scrolling on the
LCD display; otherwise, they will not.
9. AF [ALTERNATIVE FREQUENCIES] BUTTON
When pressing the AF button briefly,the AF switching mode is selected and the AF
switching mode is displayed by AF segment in display.
4.23 The DVD System Menu Setup Operation
Segment off: AF switching mode off.
Segment on: AF switching mode on, and has RDS information.
Segment flashing: AF switching mode on, but RDS information is not received yet.
1. Press the SETUP button on the remote control to access the DVD System
Menu on the monitor.
When the AF switching mode is selected, the radio checks the signal strength
of the AF all the time. The interval of checking time of each AFs depends on
the signal strength of the current station, from a few minute for the strong
station to a few seconds for the weak station. Every time when a new AF is
stronger than the current station, it switches over to that frequency for very
short time, and the NEW FREQUENCY is displayed for 1-2 second. Because
the mute time of the AF switching or the checking time is very short, it is almost
inaudible in case of normal program. (When AF flashes on the monitor, it will
search for the stronger RDS station. If AF and TP flash on the monitor, it can
only search for the traffic announcement station).
4.19 Program Playback
It allows you to enter the order in which you want some chapters/tracks in
DVD/VCD/MP3/WMA/CD to play.
1 During playback, press the PROG button to enter a program interface as
follows:
In FM mode, when AF is on, SEEK, (SCAN), AUTO-MEMORY functions can
only receive and save the RDS program.
10. TA [TRAFFIC ANNOUNCEMENT] BUTTON
Press the TA button briefly to turn on TA search mode.
When traffic announcement is transmitted:
1).If the unit is in Disc Play mode, it will switch to radio mode temporarily.
2).Temporarily switches over to an station with traffic announcement, and TA,
TP will be displayed on the monitor.
2 Use the direction buttons to move cursor onto the desired place for inputting
the sequence number.
3 Use the number button to input desired sequence number of title/chapter/
* TA interruption function:
The current traffic announcement is cancelled by pressing TA button briefly.
* When TA is on, SEEK, (SCAN), AUTO MEMORY functions can be received
or saved only when traffic program identification code has been received.
track with desired sequence.
4 Use the direction button to move cursor onto Play item, then press the OK
button to play the programmed titles/chapters/tracks in programmed order;
only pressing the PLAY button also can play the programmed titles/chapters
/tracks in programmed order.
4. Disc and USB Operation
*
*
*
*
To exit program playback, firstly press the STOP button, then press the PLAY
button to enter sequence playback; or press the PROG button twice again.
To remove the all programmed sequence numbers, move the cursor onto
Clear item, then press the OK button.
To change the programmed sequence, move the cursor onto the item you
want to change, input the desired sequence number.
4.1 Load/unload disc or USB
To play files in a disc or card, press the EJECT button to slide down the monitor .
Then insert the disc or card into the disc slot or SD/MMC Card slot.
To unload the disc or card, press the STOP button twice to stop playback, then
press the EJECT button to slide down the monitor and eject disc in the disc slot
and then remove the disc; or push the card firstly and pull it out of the card slot.
During VCD playback, if it is in PBC ON mode, at the same time of entering
the state of program playback, it turns off PBC mode.
4.20 Playback IMAGE files
To play files in an USB, insert the USB into the USB jack connecting to the Rear
cabinet.
To unload the USB, press the STOP button twice and then remove the USB .
1. The root menu is displayed on the monitor when beginning to switch on IMAGE
mode. .
In the root menu, the left file sort icon is for MP3/WMA file; the middle file sort
icon is for IMAGE file; the right file sort icon is for VIDEO file. If one of these 3
file sort does not exist, you can not move cursor onto the file sort icon.
2. When displaying the root menu, press the direction buttons to select your
desired FOLDER, file or file sort icon, then press the OK or PLAY button to
open the FOLDER, or play the selected file, or play only this sort of file.
When displaying the root menu, you can also use the number buttons to
select the serial number of the file and play the file.
In USB or CARD mode, select your desired as right.
Remark: the
is for video files; the
Tap the icon to turn to main menu, tap the
icon to turn to previous setting.
icon is for audio files; the
icon
icon is for image files.
USB/CARD INTERFACE
ZOOMx2,ZOOMx3,ZOOMx4,ZOOMx1/2,ZOOMx1/3,ZOOMx1/4,ZOOM OFF.
Press one of the ^/v/>/< buttons to select the area you want to enlarge.
: Tap it can pause playback
: Tap it can stop playback .
4.16 Change the Caption Language
:Tapping one of them can switch on between
the speed levels of fast backward or forward.
(Except image mode.)
When playing DVD , press the SUBTITLE button repeatedly to select the
language of the caption or turn off the caption.(depend on the media used.)
: Tapping one of them can select next or
previous chapter/track.
When playing VCD/MP3/WMA/CD , the button is not available.
Root interface for MUSIC
: Tap it to turn volume up and down.
4.17 Change the Audio Language
: Tap it to turn the selecting page up and down.
: Tap it to select INT play mode(Except image mode.)
1. When playing DVD , press the AUDIO button repeatedly on the IR remote
control to select the desired language type. (depend on the media used)
: During VCD playback, tap it can select the audio
ST/MONO .
2. When playing VCD , press the AUDIO button repeatedly to select the sound
mode of the MONO L, MONO R, MIX MONO and Stereo, no language function.
: Same as the MENU button on the remote control.
: Same as the TITLE button on the remote control.
: Same as the REPEAT button on the remote control.
: Same as the SUBTITLE button on the remote control.
Keyboard interface-1
3. When playing CD/WMA/MP3 , the AUDIO button is disabled.
4.18 Look over the Playback Status
1. When playing DVD , press the OSD button repeatedly on the remote control
to turn on/off the playback status. When it is on, it will display the information
such as: the serial number of the playing title, the serial number of the playing
chapter, the elapsed time of the playing chapter, the remained time of the
playing chapter, the elapsed time of the playing title, the remained time of the
playing title, etc.
: Tap it to select the track from 1-9 and then select
OK to play your selecting.
: During playback, press the ZOOM button
and then tap one of them are same as the direction
buttons on the Remote Control.
(Except music & image mode.);
During playback, press one of them to change the
playback angle.
Keyboard interface-2
2. When playing VCD/CD , press the OSD button repeatedly on the remote
control to turn on/off the playback status. When it is on, it will display the
information such as: the serial number of the playing track, the elapsed time
of the playing track, the remained time of the playing track, the elapsed time
of the disc, the remained time of the disc.
(Only for image mode.)
: Same as the ZOOM button on the Remote Control.
: Same as the RDM button on the Remote Control.
3. When playing MP3/WMA , press the OSD button repeatedly on the remote
control to turn on/off the playback status. When it is on, it will display the
information such as: the serial number of the playing track, the elapsed time
of the playing track, the remained time of the playing track.
: During DVD playback, tap the icon to change the
playback angle.
Keyboard interface-3
Note: This unit has front and rear USB. Only one will work at a time.
4.11 Playback in Scan Mode
4.2 Pause Playback
1. When playing VCD(PBC OFF)/CD , press the INT button to play the previous
15 seconds part of each track on the disc. Press the INT button again to
resume normal playback.
When playing DVD/VCD/CD/MP3/WMA , press the PAUSE button on IR
remote control to pause the playback, press the PLAY button to resume
normal playback.
2. When playing DVD/MP3/WMA , the INT button is not available.
4.12 Playback from a specified chapter/track or a specified time
4.3 Stop Playback
When playing DVD/VCD/MP3/WMA/CD , press the STOP button once to
pause the playback, then press the PLAY button to resume the normal
playback; press the STOP button twice to full stop the playback, then press
the PLAY button to start playing from the beginning of the first chapter/track.
1. When playing DVD , press the SEARCH button to display a interface and
highlight the title item, then use the number buttons to input the serial number
of the title; use the direction buttons to highlight the chapter item, then use the
number buttons to input the serial number of the chapter; you can still use the
direction buttons to highlight the time item, then use the number buttons to
input the desired time to start playback; finally press the OK or PLAY button
to play the selected chapter or play from the selected time.
4.4 Select Chapter/Track with the >>| or |<< Button
Press the >>| or |<< button during playback to select the next or previous
chapter/track to playback.
2. When playing VCD/MP3/WMA/CD , press the SEARCH button to display a
interface and highlight the track item, then use the number buttons to input
the serial number of the track; you can still use the direction buttons to
highlight the time item, then use the number buttons to input the desired
time to start playback; finally press the OK or PLAY button to play the selected
track or play from the selected time.
Note: Press the >>| or |<< button multiple times to advance multiple chapters/
tracks forward or backward.
4.5 Select Chapter/Track with the Number Buttons
4.13 Playback in Random
When playing DVD/VCD(PBC OFF)/MP3/WMA/CD , press one of the 1~9
and the 0/10 number buttons to directly select and play the 1st to 10th track
/chapter (the 0/10 button is used as the 10 button).
When playing DVD/VCD(PBC OFF)/MP3/WMA/CD , press the RDM button to
switch between RANDOM (ON)/RANDOM OFF. When in RANDOM (ON) mode,
it will play in random.
If you want to play the track/chapter larger than 10, use the 10+, 1~9 and
0/10 button. Example 1: to play the 13th track/chapter, first press the 10+
button once, then press the 3 button. Example 2: to play the 34th track/
chapter, first press the 10+ button 3 times, then press the 4 button.
(The 0/10 button is used as the 0 button)
4.14 Playback in Different View-Angle
1. When playing VCD/MP3/WMA/CD , the VIEW-ANGLE button on the IR remote
control is not available.
Note: long pressing the +10 or -10 button can play the next 10th or previous
10th chapter/track(only for MP3/WMA).
2. When playing DVD , press the VIEW-ANGLE button repeatedly on the IR
remote control to view in different angle.(This function is only for the DVD
media with ANGLE function)
4.6 Select Chapter/Track with the Root/PBC Menu (If the disc includes the
root/PBC menu)
4.15 Playback in Zoom Mode
When playing DVD
In video/image mode, during playback, press the ZOOM button continuously
to enlarge a certain area of the images on the screen with these multiples:
1. Press the TITLE button on the remote control to display the title list.
During slow forward, press the PLAY button to resume normal playback.
This function is only for video.
2. Press the direction buttons to select your desired title, and then press the
OK or PLAY button to open the root menu of the selected title.
3. Press the direction buttons to select your desired chapter, finally press the
OK or PLAY button to play the selected chapter.
4.9 Display still frame step by step
If the unit is currently playing video, press the STEP button consecutively
to display still frame step by step.
Press the PLAY button to resume normal playback.
During playback, pressing the MENU button can directly display the root
menu of the title that is playing.
In VCD mode
4.10 Playback Repeatedly
4.10.1 ONE/ALL Repeat
1. When starting to turn on the PBC function, it will play from the beginning of
the disc till it display the PBC menu on the screen if the disc include the PBC
menu.
1. In the mode of DVD playback:
2. Press the number buttons to select your desired track to play.
In MP3/WMA mode
Press the RPT button to select REP CHAPTER, REP TITLE, REP ALL
or REP OFF.
2. In the mode of VCD(PBC OFF)/CD playback:
1. The root menu is displayed on the monitor screen all the time(and the TITLE
or MENU button is not available).
press the RPT button to select REP ONE, REP ALL or OFF.
When it is in the state of PBC ON, during VCD disc playing, the RPT
button are not available.
2. Press the direction buttons to select your desired FOLDER, then press the
OK or PLAY button to open the FOLDER, and then press the direction buttons
to select your desired file, finally press the OK button to play the selected file.
3. In the mode of MP3/WMA playback:
Press the RPT button to select REP ONE, REP DIR, REP ALL or OFF.
In CD mode, the TITLE, PBC, MENU buttons are disabled.
4.10.2 A-B Repeat
4.7 Playback with Speed
Press the A-B button if you want to repeat a specific segment on a disc
that you define:
During normal playback, consecutive pressing of the >>| or |<< button
will fast forward or rewind at the following speeds: x2, x4, x8, x20, normal.
1. Press the A-B button at a point (A) where you want it to be the start point
of the repeat segment. Press the A-B button again at a point (B) where you
want it to be the terminal point of the repeat segment. Then it will play the
segment repeatedly.
During this operation, press the PLAY button to resume normal playback.
4.8 Playback with Slow Speed
2. To cancel the A-B repeat mode and resume normal playback, press the A-B
During playback , press the SLOW_FWD button to execute the Slow Forward
function.
button for the third time.
Note:
With each consecutive pressing of the SLOW_FWD button, the playback
speed decreases. The speed levels in Slow Forward as follows:
x1/2,x1/3,x1/4,x1/5,x1/6,x1/7,normal.
During VCD/MP3/WMA/CD playback, points A and B must be within the
same track.
During DVD playback, points A and B can be selected from different chapters.
|