DCN Next Generation
Intercom
en Software User Manual
LBB 4173/00
Download from Www.Somanuals.com. All Manuals Search And Download.
DCN Next Generation Intercom
en | 3
Table of contents
Bosch Security Systems B.V. | 2005 January | 9922 141 70371
Download from Www.Somanuals.com. All Manuals Search And Download.
DCN Next Generation Intercom
en | 4
1 Intercom
i
Note
It is not possible to start Intercom if 30 or more
language channels have been selected in the
System Installation module.
1.1 About Intercom
1.1.1 What is Intercom?
The Intercom module is one of the software modules
designed for monitoring and controlling conferences
and discussions using the contribution equipment.
Intercom provides a means of setting up and
controlling intercom calls between delegates,
chairmen and interpreters during a conference. It
allows several types of calls to be made:
•
•
•
•
•
•
From participant to operator, or vice versa
Between participants, via the operator or directly
From interpreter to operator, or vice versa
From interpreter to chairman
Between interpreters, via the operator or directly
From participant to interpreter, or vice versa, via
the operator or directly
The Intercom software is used in combination with
the intercom handset. This unit can be attached to
chairman and delegate units, and allows private two-
way communication in the manner of a normal
telephone conversation.
The software provides assistance in both the pre-
conference creation of an intercom network, and the
routing and controlling of intercom calls once the
conference is under way. Preparation work includes
assigning special intercom links between participants,
interpreters or a combination of both.
Those to receive intercom facilities can be identified
either by the seat number assigned using System
Installation (LBB 4185) or the screen line assigned
using Delegate Database (LBB 4180). A search
facility is available to simplify this task. Once the
conference is taking place, the operator can establish
and re-route intercom calls via simple on-screen
windows. The Intercom module differs from other
software modules in that it is automatically activated
from an iconized state if an intercom call is made by
a participating delegate.
The number of audio channels available for intercom
purposes is set using the System Installation software.
The minimum available number of channels is zero,
and the maximum is 6. The first channel is used for
busy and ring-tones, the other channels are the actual
intercom channels so the maximum number of
simultaneous calls possible is 5. When no channels
are assigned for intercom purposes, the Intercom
software module cannot be used.
Bosch Security Systems B.V. | 2005 January | 9922 141 70371
Download from Www.Somanuals.com. All Manuals Search And Download.
DCN Next Generation Intercom
en | 5
The software uses two user-created files that contain
2 Getting started
important information about the installed hardware
configuration and about delegates’ names. These files
are:
•
Installation file - containing information about
channel assignment and the numbers that have
been assigned to all microphones connected to
the system. These seat numbers are assigned
using the System Installation software (LBB 4185).
Names file - containing information about the
name, seat number and other conference and
personal details of participating delegates. Names
files are created using the Delegate Database
software (LBB 4180).
2.1 Starting Intercom
2.1.1 The Startup screen
The Intercom program is started from the Startup
screen (shown below).
•
The software modules may be started up from the
Startup main window without specifying either an
installation or names file. However, some software
modules will not run without the appropriate
installation or names file.
Intercom makes use of the information contained
both in an installation file and a names file. The
screen line as specified in a names file is used by
Intercom to define delegates. The seat numbers
assigned using System Installation and contained in
an installation file are also used. The number of
communication channels to be used for intercom
purposes is also assigned using System Installation
and contained in an installation file.
Figure 1 The Startup screen
Selecting an installation- (and a names) file
For details on selecting an installation- (and a names)
file, please refer to the Startup user manual (LBB
4190).
i
i
Note
For starting the Startup program from an icon
at the Windows desktop, refer to the Startup
user manual.
The Intercom icon
For details on the Intercom icon and how to start
Intercom from Startup, please refer to the Startup
user manual (LBB 4190).
Note
If there are no intercom channels assigned in
the System Installation module, then it will not
be possible to open the Intercom module, and
the Intercom icon will be grayed out.
2.2 Using Help
2.2.1 The Help menu
The ‘Help’ menu in the title bar contains commands
for an on-screen help facility. This help facility
contains information on all commands in the ‘File’
menu, on which keyboard keys are functional, a
description of how to use the software, information
on how to use the help facility itself, plus an index
and a glossary of terms. All information contained in
this user manual is also found in the ‘Help’ facility.
i
Note
It is not possible to start Intercom if 30 or more
language channels have been selected in the
System Installation module.
The ‘Help’ facility contains the following options:
•
Index
Bosch Security Systems B.V. | 2005 January | 9922 141 70371
Download from Www.Somanuals.com. All Manuals Search And Download.
DCN Next Generation Intercom
en | 6
•
•
•
•
•
•
Keyboard
•
Select the ‘Help’ menu and click on ‘Procedures’.
Commands
Procedures
Glossary
Using Help
About Intercom.
A list of topics is given. For more information on any
topic contained in the list:
•
Click on the required topic in the list.
A list of options for the selected topic is given. For
more information on any option contained in the list:
2.2.2 Index
To access the index:
•
Click on the required option in the list.
An on-screen page with the requested information
will appear.
•
Select the ‘Help’ menu and click on ‘Index’.
A full list of subjects covered by the help facility is
given in alphabetical order. For more information on
any subject contained in the index:
2.2.6 Glossary
To access the glossary:
•
Click on the required subject in the index.
•
Select the ‘Help’ menu and click on ‘Glossary’.
An on-screen page with the requested information
will appear.
A list of terms used in the help facility is given in
alphabetical order. For more information on any
term contained in the glossary:
2.2.3 Keyboard
•
Click on the required subject in the index.
This gives information on which keys on your
keyboard can be used with the software. This
includes using keys to activate menu items, to move
around in dialogue boxes, for short cuts, and to select
options from the main window. To access the
‘Keyboard’ help facility:
A window with the requested information will appear.
2.2.7 Using Help
This gives information on how to use the help facility.
To access the ‘Using Help’ facility:
•
Select the ‘Help’ menu and click on ‘Keyboard’.
•
Select the ‘Help’ menu and click on ‘Using Help’.
A list of different key types is given. For more
information on any key type contained in the list:
A list of topics is given. For more information on any
topic contained in the list:
•
Click on the required key type in the list.
•
Click on the required topic in the list.
An on-screen page with the requested information
will appear.
A list of options for the selected topic is given. For
more information on any option contained in the list:
•
Click on the required option in the list.
2.2.4 Commands
This gives information on all menu options, covering
the ‘File’, ‘Edit’, ‘View’, ‘Settings’ and ‘Help’ menus.
To access the ‘Commands’ help facility:
An on-screen page with the requested information
will appear.
•
Select the ‘Help’ menu and click on ‘Commands’.
2.2.8 About
This provides software release information. To
display the ‘About Intercom...’ window:
A list of menu groups is given. For more information
on any menu group contained in the list:
•
Select the ‘Help’ menu and click on ‘About
Intercom...’.
•
Click on the required menu group in the list.
A list of options in the selected menu group is given.
For more information on any option contained in the
list:
The following window appears:
•
Click on the required option in the list.
An on-screen page with the requested information
will appear.
2.2.5 Procedures
This gives information on how to use the software.
To access the ‘Procedures’ help facility:
Bosch Security Systems B.V. | 2005 January | 9922 141 70371
Download from Www.Somanuals.com. All Manuals Search And Download.
DCN Next Generation Intercom
en | 7
Figure 2 The ‘About Intercom...’ window
To remove this window:
•
Click on the ‘OK’ push button.
Bosch Security Systems B.V. | 2005 January | 9922 141 70371
Download from Www.Somanuals.com. All Manuals Search And Download.
DCN Next Generation Intercom
en | 8
3 Preparing for a conference
i
Note
The number of available lines depends on the
number of intercom lines specified using
System Installation. When no channels are
assigned for intercom purposes, the Intercom
software module cannot be used.
3.1 The main window
The Intercom main window is used to display
incoming intercom calls from delegates, chairmen or
interpreters, to select a destination for the calls, and
to connect the caller with the appropriate destination.
You can also initiate intercom calls yourself.
The information displayed in the ‘Call From’ display
field is dependent on who has initiated the call. The
following possibilities exist:
•
‘<Delegate/chairman screen line>, <seat number>’.
This indicates that an intercom call has been
made by a chairman or delegate, and that the
following conditions have been met:
From the main window you can also access the menu
bar, which allows you to edit intercom files, set up
and delete special intercom links, alter settings and
access the Help menu.
•
a names file has been opened
•
a screen line has been assigned to the calling
chairman/delegate
•
the chairman/delegate has been identified to
the DCN system as the user of the unit from
where the intercom call is made
i
Note
The order in which this information is displayed
is determined by the ‘Search’ mode. If ‘Names’
is selected, the screen line will appear first,
followed by the seat number. If ‘Number’ is
selected, the seat number will appear first,
followed by the screen line.
•
•
‘<Seat number>’ indicates that an intercom call
has been made by a chairman or delegate, but no
names file has been opened, and/or no
chairman/delegate has been identified to the
DCN system as the user of the unit from where
the intercom call is made.
‘Interpreters Booth <N>, Desk <M>.’ This
indicates that an intercom call has been made by
an interpreter. <N> indicates the booth number
of the interpreter, and <M> gives the desk
number within the booth.
Figure 3 The main window
The main window can be divided into three parts.
The upper part of the window is used to display
information on the person who wishes to initiate an
intercom call. The middle part is used to select a
destination for this call.
The lower part of the screen has a push button that is
used to connect the caller to the destination.
i
Note
The main window contains the following elements:
When an intercom call is made to the operator
by a user (i.e. a chairman, delegate, interpreter),
this is registered by the appearance of the
‘Connect To’ window. For more details, please
refer to paragraph 4.1.
•
•
•
‘Call From’ static text and display field
Group of two ‘Connect To’ radio buttons
List box displaying all those eligible to receive
the call using ‘Connect To’
•
•
•
‘Search’ radio buttons, push button and edit box
Menu bar
‘Connect’ push button with text displaying the
number of available lines
3.1.1 The menu bar
All menu options referred to in this user manual are
contained within the menu bar, located underneath
the title bar at the top of the main window. Access to
drop-down menus is gained by clicking on the menu
Bosch Security Systems B.V. | 2005 January | 9922 141 70371
Download from Www.Somanuals.com. All Manuals Search And Download.
DCN Next Generation Intercom
en | 9
title, displayed in the menu bar. The full list of menu
options is as follows:
i
Note
File
Edit
Settings
Help
Clicking on ‘Cancel’ closes the dialogue box
without initiating commands and/or changes.
This applies to all dialogue boxes in the
Intercom program.
New…
Links…
Ring Tone
Index…
Open…
Save
Intercom Activity…
Keyboard
Commands
Procedures
Glossary
Save As…
Delete…
Print Activity…
Exit
If you have requested to open a new intercom file
before saving a current intercom file that has been
changed, a warning message with the following text is
displayed:
Using Help
About Intercom…
‘Changes have been made to <filename>.’
‘Do you want to save?’
3.2 Working with intercom files
•
•
•
Click on the ‘Yes’ push button to save the
changed intercom file and open the new
intercom file.
3.2.1 Intercom file options
The ‘File’ menu has commands for:
• Click on the ‘No’ push button to open the new
intercom file without saving the changed
intercom file.
•
•
•
•
•
•
•
Opening a new intercom file
Opening an existing intercom file
Saving an intercom file under its current name
Saving an intercom file under a different name
Deleting an intercom file
Printing intercom activity
Exiting the Intercom program
• Click on the ‘Cancel’ push button to return to
the ‘New’ dialogue box.
If you have typed a filename that already exists, a
warning message with the following text is displayed:
‘A file already exists with this name’
i
Note
•
Click on the ‘OK’ push button. You can then
enter a unique name in the ‘New’ dialogue box.
Exiting Intercom is covered in paragraph 4.4
and printing is covered in paragraph 4.34.4
Opening an existing intercom file
To do so:
Creating a new intercom file
To open a new intercom file:
•
Select the ‘File’ menu and click on ‘Open...’.
•
Select the ‘File’ menu and click on ‘New...’.
The following dialogue box appears:
The following dialogue box appears:
Figure 4 The ‘New’ dialogue box
The dialogue box contains a text box for entering the
file name. A text insertion point is already in the text
box and you can type a name up to 12 characters
long.
•
Type the desired intercom file name in the text
box.
Figure 5 The 'Open' dialogue box
This dialogue box contains a list box for selecting the
intercom file name. The name of the current
intercom file is also displayed. When the ‘Open’
dialogue box opens, the list box contains all available
intercom files. If the list contains more names than
•
Click on the ‘Ok’ push button.
A new intercom file opens and the name appears in
the title bar at the top of the window.
Bosch Security Systems B.V. | 2005 January | 9922 141 70371
Download from Www.Somanuals.com. All Manuals Search And Download.
DCN Next Generation Intercom
en | 10
can be displayed, a scroll bar is provided.
To open an intercom file:
The following dialogue box appears:
•
Click on the name in the list.
•
Click on the ‘Ok’ push button.
If you have requested to open a new intercom file
before saving a current intercom file that has been
changed, a warning message with the following text is
displayed:
‘Changes have been made to <filename>.’
‘Do you want to save?’
Figure 6 The ‘Save As’ dialogue box
•
•
•
Click on the ‘Yes’ push button to save the
changed intercom file and open the new
intercom file.
This dialogue box contains a text box for entering
the new intercom file name. When the ‘Save As...’
dialogue box opens, a text insertion point is already
in the text box and you can type a name up to 12
characters long.
Click on the ‘No’ push button to open the new
intercom file without saving the changed
intercom file.
•
Type the desired intercom file name in the text
box.
Click on the ‘Cancel’ push button to return to the
‘New’ dialogue box.
•
Click on the ‘Ok’ push button.
The intercom file is saved with the new name, which
appears in the title bar at the top of the window. The
original file is unchanged. If you have typed a
filename that already exists, a warning message with
the following text is displayed:
Saving an intercom file
To save the current intercom file:
•
Select the ‘File’ menu and click on ‘Save’.
‘A file already exists with this name’
Saving an intercom file under a new name
This allows you to save the current intercom file
under a different name. By doing so, the original file
remains unaltered. To do so:
•
Click on the ‘OK’ push button. You can then
enter a unique name in the ‘Save As’ dialogue
box.
•
Select the ‘File’ menu and click on ‘Save As...’.
Deleting an intercom file
If you wish to delete an intercom file:
•
Select the ‘File’ menu and click on ‘Delete...’.
The following dialogue box appears:
Figure 7 The ‘Delete’ dialogue box
This dialogue box contains a list box for selecting the
file to be deleted. A scroll bar is provided if
necessary.
Bosch Security Systems B.V. | 2005 January | 9922 141 70371
Download from Www.Somanuals.com. All Manuals Search And Download.
DCN Next Generation Intercom
en | 11
•
•
•
•
‘Search’ radio buttons, push button and edit box
‘Special Links’ list box
‘Delete’ push button
•
•
Click on the name in the list.
Click on the ‘Delete’ push button.
‘OK’ and ‘Cancel’ push buttons
Another dialogue box will appear, with the text:
‘Are you sure you want to delete file
<filename>’
Determining where the special link begins
This option allows you to select a delegate, chairman
or interpreter who can initiate a special intercom call.
To select a delegate/chairman:
If you still want to continue:
•
Click on the ‘OK’ push button.
•
Click on the ‘Delegates’ radio button (if this
option is not already enabled).
To select an interpreter:
i
Note
You cannot delete the currently active file.
•
Click on the ‘Interpreters’ radio button (if this
option is not already enabled).
3.3 Setting up special intercom links
The Intercom software allows you to set up special
intercom links between conference participants, or
between participants and interpreters, or between
interpreters. These special links mean that the
selected people can call each other directly.
Normally, intercom calls must go through the
operator.
If ‘Delegates’ has been selected, the ‘From’ list box
will display an alphabetical list of all delegates and
chairmen that can initiate an intercom call, i.e. those
who:
•
have a valid seat number in the currently open
installation file
•
•
are connected to an intercom handset and cradle
have not already been used as the ‘From’ part of
a special intercom link
The special links always have a direction, i.e. they go
from one person to another. Only one special link
can come from a single person, but anyone can
receive as many as the system permits.
Each delegate or chairman will be identified by a
screen line and seat number, or only a seat number if
no screen line has been specified. Whether the seat
number or screen line is displayed first depends on
which ‘Search’ mode has been selected.
The setting up of special intercom links is carried out
from the ‘Special Intercom Links’ dialogue box.
If ‘Interpreters’ has been selected, the ‘Connect To’ list
box will display a list of all installed interpreters.
•
Select the ‘Edit’ menu and click on ‘Links...’.
The following dialogue box appears:
i
Note
What is displayed for interpreters is based on
information contained within an interpreter
configuration file in the Simultaneous
Interpretation software module (LBB 4172). If
no booth/desk numbers have been defined, or
the Simultaneous Interpretation program is not
open, then there will be no information
displayed in the ‘From’ list box.
Each interpreter will be identified by ‘Booth <N>,
Desk <M>’, where <N> indicates the booth number
of the interpreter, and <M> gives the desk number
within the booth.
Figure 8 The ‘Special Intercom Links’ dialogue box
To select a delegate, chairman or interpreter:
This dialogue box contains the following elements:
•
Click on the name in the list.
•
•
•
•
•
•
‘From:’ list box, with
‘Delegates’ and ‘Interpreters’ radio buttons
‘Search’ radio buttons, push button and edit box
‘Link’ push button
‘To:’ list box, with
‘Delegates’ and ‘Interpreters’ radio buttons
If you wish to change your selection, simply repeat
the procedure.
Bosch Security Systems B.V. | 2005 January | 9922 141 70371
Download from Www.Somanuals.com. All Manuals Search And Download.
DCN Next Generation Intercom
en | 12
Search
•
Click on the ‘Search’ push button.
This option allows you to conduct a search for a
particular delegate, chairman or interpreter. There
are two ‘Search’ radio buttons, a ‘Search’ push button
and a list box:
Once the search is completed, the list box displays all
entries corresponding to the input details. You can
select the desired entry by clicking on it.
Determining who the special link goes to
This option allows you to select a delegate, chairman
or interpreter as the destination of a special intercom
link.
The procedure for locating a person to receive a
special intercom link is identical to the procedure for
selecting where the special link comes from. For
more information on how to locate delegates,
chairmen or interpreters and conducting a search,
please refer to page 11.
Figure 9 The ‘Search’ facility
You can specify whether the search is conducted by
screen line (‘Names’) or seat number (‘Numbers’)
when searching for a delegate or chairman.
The conditions under which delegates, chairmen or
interpreters appear in the ‘To’ list box are identical to
the conditions for the ‘From’ list box, except that
names still appear in the list even if they are already
the destination of a special intercom link. This means
in effect that one person can receive any number of
special links.
i
Note
When ‘Interpreters’ is selected, a ‘Search’ is
carried out to locate interpreters. In this case
the ‘Names’ and ‘Numbers’ radio buttons are
deactivated, and you must enter ‘<N>, <M>’ in
the text box located under the ‘Search’ push
button, where <N> and <M> are the booth
number and desk number of the interpreter
respectively.
To select a delegate, chairman or interpreter to
receive the special intercom link:
•
Click on the name in the list.
To choose the mode not currently selected:
Making the link
•
Click on the radio button without the black circle.
Once you have made a selection in the ‘From:’ list
box and the ‘To:’ list box, the arrow-shaped ‘Link’
push button, situated between the two list boxes,
becomes active. To make the link:
i
Note
Specifying the ‘Search’ mode also determines
the way information is displayed in the
•
Click on the ‘Link’ push button.
‘Connect To’ list box. If ‘Names’ is selected,
then the list is arranged alphabetically by
screen line, with the seat number displayed
after each screen line. If ‘Numbers’ is selected,
then the list is arranged by seat number, in
ascending numerical order. The screen line (if
specified) is displayed after each seat number.
A special intercom link is made. The entry selected
in the ‘From’ list box is removed and inserted in the
‘Special Links’ list box under the ‘From’ column. The
entry selected in the ‘To’ list box is de-selected (but
not removed) and appears in the ‘Special Links’ list
box under the ‘To’ column.
Deleting special intercom links
To delete a special intercom link:
You can specify a particular delegate or chairman
you wish to search for. This is done by entering the
details of the required delegate/chairman in the text
box situated under the ‘Search’ push button. If
‘Numbers’ has been specified for the search, you may
only enter up to four alphanumeric characters. If
‘Names’ has been specified for the search, then the
maximum number of characters allowed equals the
maximum length of the screen line. To search:
•
Select an entry in the ‘Special Links’ list box.
•
Click on the ‘Delete’ push button.
The special link will be deleted. The person that the
link came from will be re-inserted at the appropriate
position in the ‘From’ list box.
•
Click on the text box under the ‘Search’ push
button.
When you have finished setting up special links:
•
Click on the ‘OK’ push button.
•
Type the details of the required delegate in the
text box.
You will return to the main window.
Bosch Security Systems B.V. | 2005 January | 9922 141 70371
Download from Www.Somanuals.com. All Manuals Search And Download.
DCN Next Generation Intercom
en | 13
To disable logging again:
Click on the ‘Off’ radio button.
3.4 Specifying intercom settings
You can specify intercom-related parameters using
the ‘Settings’ menu. The ‘Settings’ menu is accessed
from the main window, and has two options:
•
The ‘Send To File’ edit field allows you to specify the
destination file of the logging activity. You can enter
a file name, which must be a valid MS-DOS name no
longer than eight characters. To do so:
•
Ring Tone
•
Intercom Activity
3.4.1 Ring Tone
•
Click on the ‘Send To File’ text box.
This option allows you to enable or disable an
audible tone that sounds every time an intercom call
is made to the operator. The default state is ‘enabled’.
To disable the tone:
•
Type in the file name.
If you enter an invalid filename and/or location, or
do not enter one at all, a warning message with the
following text is displayed:
•
Select the ‘Settings’ menu and click on ‘Ring
Tone’.
‘Invalid filename’
The tick mark (√) will subsequently disappear,
indicating that the ring tone has been disabled.
To turn the ring tone back on:
•
Click on the ‘Ok’ push button.
You will return to the dialogue box and can enter a
valid filename and/or location.
•
Select the ‘Settings’ menu and click on ‘Ring
Tone’ again.
i
i
Note
The tick mark (√) will subsequently appear,
indicating that the ring tone has been enabled again.
The destination file(s) for Intercom activity
logging are located in the DCNNG\Iclog
directory.
3.4.2 Logging intercom activity
This option allows you to enable or disable the
logging of all intercom activity. You can also specify
the name of the file where logging information will
be stored. To do so:
Note
It is possible to print an intercom activity file. To
do so, please refer to paragraph 4.3.
•
Select the ‘Settings’ menu and click on ‘Intercom
Activity’.
Once you have finished specifying all parameters in
the ‘Intercom Activity’ dialogue box:
The following dialogue box appears:
•
Click on the ‘Ok’ push button.
Any changes made will be saved, and you will return
to the main window.
Figure 10 The ‘Intercom Activity’ dialogue box
The ‘Logging’ radio buttons allow you to enable or
disable intercom activity logging. The default state is
‘off’. To enable logging:
•
Click on the ‘On’ radio button.
A black circle will appear to indicate this option has
been selected.
Bosch Security Systems B.V. | 2005 January | 9922 141 70371
Download from Www.Somanuals.com. All Manuals Search And Download.
DCN Next Generation Intercom
en | 14
4.1.1 Routing incoming intercom calls
4 Intercom activity during a
conference
If the call is a request from a user to speak to another
user, you must call up the main window in order to
route and connect the call. To do so:
•
Click on the ‘Connect To...’ push button.
4.1 Handling incoming intercom calls
When an intercom call is made to the operator by a
user (i.e. a chairman, delegate, interpreter), this is
registered by the appearance of the following window
on-screen:
The ‘Connect Request’ dialogue box disappears and
the following dialogue box appears:
Figure 11 The ‘Connect Request’ dialogue box
i
Note
This dialogue box appears even if the Intercom
software module was iconized.
Figure 12 The ‘Intercom’ dialogue box
The presence of an incoming call is also registered by
a single ring tone, if this option has been enabled.
For more details, please refer to paragraph 3.4.
i
Note
The ‘Connect Request’ window also
disappears if the caller or the operator hangs
up.
The ‘Connect Request’ dialogue box contains the
following elements:
•
‘Call From’ text
The field below the ‘Call From’ text identifies the
caller.
•
Text identifying the caller. This can be in the
form of screen line/seat number, seat number
only or interpretation booth and desk number.
For details of which information appears, please
If you wish to connect the caller with another
delegate/chairman:
•
•
‘Please lift handset’ text
‘Connect To...’ push button
•
Click on the ‘Delegates’ radio button (if this
option is not already enabled).
When this window appears:
If you wish to connect the caller to an interpreter:
•
Pick up the handset connected to the PC to
answer the call.
•
Click on the ‘Interpreters’ radio button (if this
option is not already enabled).
If ‘Delegates’ has been selected, the ‘Connect To’ list
box (located beneath the ‘Connect To’ radio buttons)
will display an alphabetical list of all delegates and
chairmen that can receive an intercom call. To be
eligible, they must have the following:
i
Note
If the incoming call is not answered by the
operator within 60 seconds, it will be
cancelled.
•
A valid seat number in the currently open
installation file
•
A connection to an intercom handset
Each delegate or chairman will be identified by a
screen line and seat number, or only a seat number if
Bosch Security Systems B.V. | 2005 January | 9922 141 70371
Download from Www.Somanuals.com. All Manuals Search And Download.
DCN Next Generation Intercom
en | 15
no screen line has been specified. Whether the seat
number or screen line is displayed first depends on
which ‘Search’ mode has been selected.
i
Note
When ‘Interpreters’ is selected, a ‘Search’ can
only be carried out to locate interpreters, and
can therefore only be done by ‘Numbers’,
where numbers is ‘Booth <N>, Desk <M>’.
If ‘Interpreters’ has been selected, the ‘Connect To’ list
box will display a list of all interpreters who can
receive an intercom call.
To choose the mode not currently selected:
•
Click on the radio button without the black circle.
i
Note
What is displayed for interpreters is based on
information contained within an interpreter
configuration file in the Simultaneous
Interpretation software module (LBB 4172). If
no booth/desk numbers have been defined, or
the Simultaneous Interpretation program is not
open, then there will be no information
i
Note
Specifying the ‘Search’ mode also determines
the way information is displayed in the
‘Connect To’ list box. If ‘Names’ is selected,
then the list is arranged alphabetically by
screen line, with the seat number displayed
after each screen line. If ‘Numbers’ is selected,
then the list is arranged by seat number, in
ascending numerical order. The screen line (if
specified) is displayed after each seat number.
displayed in the ‘‘Connect To’ list box.
Each interpreter will be identified by ‘Booth <N>,
Desk <M>’, where <N> indicates the booth number
of the interpreter, and <M> gives the desk number
within the booth.
You can specify a particular delegate or chairman
you wish to search for. This is done by entering the
details of the required delegate/chairman in the text
box situated under the ‘Search’ push button. If
‘Numbers’ has been specified for the search, you may
only enter up to four alphanumeric characters. If
‘Names’ has been specified for the search, then the
maximum number of characters allowed equals the
maximum length of the screen line.
Selecting a delegate, chairman or interpreter for
connection
The procedure for selecting a person to receive the
intercom call is always the same, regardless of
whether a delegate, chairman or interpreter is
selected. To do so:
•
Click on the name in the list.
To search:
If you wish to change your selection, simply repeat
the procedure.
•
•
•
Click on the text box under the ‘Search’ push
button.
Search
This option allows you to conduct a search for a
particular delegate or chairman. The ‘Search’ facility
is located beneath the ‘Connect To’ list box. There are
two ‘Search’ radio buttons, a ‘Search’ push button and
a list box:
Type the details of the required delegate in the
text box.
Click on the ‘Search’ push button.
Once the search is completed, the list box displays all
entries corresponding to the input details. You can
select the desired entry by clicking on it.
Connecting an incoming call
Once you have selected the destination of the
intercom call, you can connect it to the caller. This is
done by means of the ‘Connect’ push button at the
bottom of the dialogue box. This button is enabled if
the following conditions are met:
Figure 13 The ‘Search’ facility
You can specify whether the search is conducted by
screen line (‘Names’) or seat number (‘Numbers’)
when searching for a delegate or chairman.
•
The handset of the operator’s intercom unit is
not on the cradle.
•
•
An item has been selected in the ‘Connect To’ list
There are intercom lines available. If there are
no intercom lines available, the text beneath the
‘Connect’ push button will say ‘(No Lines
Available)’.
Bosch Security Systems B.V. | 2005 January | 9922 141 70371
Download from Www.Somanuals.com. All Manuals Search And Download.
DCN Next Generation Intercom
en | 16
To connect:
If you wish to change your selection, simply repeat
the procedure.
•
Click on the ‘Connect’ push button.
For more details on conducting a search for a
particular delegate or chairman, please refer to page
If the connection is successful, the text beneath the
‘Connect’ push button will be updated so the number
of lines available is reduced by one. The Intercom
application will be automatically iconized.
Connecting the call
Once you have selected the destination of your
intercom call, you can make a connection by means
of the ‘Connect’ push button at the bottom of the
dialogue box. This button is enabled if the following
conditions are met:
4.2 Generating intercom calls
As the operator, you can also initiate intercom calls
to chairmen, delegates or interpreters. To do so:
•
Pick up the handset connected to the PC.
•
•
•
The handset of the operator’s intercom unit is
not on the cradle
An item has been selected in the ‘Connect To’
This causes the following dialogue box to appear:
list
There are intercom lines available. If there are
no intercom lines available, the text beneath the
‘Connect’ push button will say ‘(No Lines
Available)’.
To connect:
•
Click on the ‘Connect’ push button.
If the connection is successful, the text beneath the
‘Connect’ push button will be updated so the number
of lines available is reduced by one. The Intercom
application will be automatically iconized.
4.3 Printing
It is possible to print a record of intercom activity.
Figure 14 The ‘Intercom’ dialogue box
i
Note
The field below the ‘Call From’ text will contain the
word ‘Operator’, indicating that you have initiated the
call.
To print a log file, it is first necessary to ensure
that logging is disabled in the Intercom Activity
dialogue box (see paragraph 3.4.2).
If you wish to call a delegate/chairman:
•
Click on the ‘Delegates’ radio button (if this
option is not already enabled).
To print a record of intercom activity:
•
Select the ‘File’ menu and click on ‘Print
Activity...’.
The following dialogue box appears:
If you wish to call an interpreter:
•
Click on the ‘Interpreters’ radio button (if this
option is not already enabled).
The ‘Call To’ list box only contains
delegates/chairmen or interpreters who can receive
an intercom call. (For more details on how entries
Selecting a delegate, chairman or interpreter for
connection
The procedure for selecting a person to receive the
intercom call is always the same, regardless of
whether a delegate, chairman or interpreter is
selected. To do so:
Figure 15 The ‘Print Activity’ dialogue box
•
Click on the name in the list.
Bosch Security Systems B.V. | 2005 January | 9922 141 70371
Download from Www.Somanuals.com. All Manuals Search And Download.
DCN Next Generation Intercom
en | 17
To select the intercom activity file for printing:
•
Click on the Intercom icon.
•
Click on the arrow button on the right-hand side
of the ‘Name’ entry field. A drop-down list of files
appears.
i
Note
If an intercom call is made by a delegate,
chairman or interpreter, Intercom will
automatically re-open and a message will
•
Scroll through the list and click on the required
file. The filename appears in the entry field.
appear on-screen. For more details, please
refer to paragraph 4.1.
i
Note
4.4.2 Permanently exiting Intercom
If you wish to exit Intercom completely:
The files that appear in this list are the files
specified using the ‘Intercom Activity’ dialogue
box. For more details, please refer to paragraph
•
Select the ‘File’ menu and click on ‘Exit’.
If you have requested to exit before saving an
intercom file that has changed, a warning message
with the following text is displayed:
‘Changes have been made to <filename>.
Do you want to save?’
To specify a page header:
•
Select the ‘Page Header:’ text box. A descriptive
name may be entered up to 20 characters long.
This text box may also be left blank.
•
•
•
Click on the ‘Yes’ push button to save the
changed layout file and exit the program.
To specify the number of copies:
•
Select the ‘Number of Copies:’ field and type in
the required number. The maximum number is
nine.
Click on the ‘No’ push button to exit without
saving the changed layout file.
Click on the ‘Cancel’ push button to return to the
main window without exiting.
i
Note
When you exit Intercom you will return to the
Windows desktop.
The up and down arrow buttons on the right-
hand side of this field can be used to scroll to
the required number.
i
i
Tip
•
Click on the ‘Print’ push button.
You can also exit Intercom by clicking on the
‘close’ button on the far top-right corner of the
window.
The specified number of hard copies of intercom
activity will be printed out.
4.4 Exiting Intercom
Note
By closing the Startup program, all DCN
applications will close.
4.4.1 Temporarily exiting Intercom
It is possible to temporarily leave Intercom without
closing it down completely. To do so:
•
Click on the ‘minimize’ button situated at the
top-right of the application window.
The Intercom program will become iconized in the
Windows desktop.
i
Note
After an intercom connection has been made,
the Intercom application automatically ionizes.
To re-enter Intercom:
Bosch Security Systems B.V. | 2005 January | 9922 141 70371
Download from Www.Somanuals.com. All Manuals Search And Download.
DCN Next Generation Intercom
en | 18
Bosch Security Systems B.V. | 2005 January | 9922 141 70371
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
For more information please visit www.boschsecuritysystems.com
© 2005 Bosch Security Systems B.V.
Data subject to change without notice
January 2005 | 9922 141 70371
Download from Www.Somanuals.com. All Manuals Search And Download.
|