RF835E Wireless
PIR/Microwave Intrusion Detector with Pet Immunity
Installation Instructions
1.0 Overview
The RF835E wireless detector uses passive infraRed (PIR) technology, microwave (MW) technology, and artificial intelligence to detect
motion. The RF835E may be installed to provide immunity to false alarms caused by pets. Recommended limits are a dog up to 100 lbs.
(45 kg), 2 dogs up to 60 lbs. (27 kg) combined weight, or up to 10 cats. An integral RF transmitter sends alarm, low battery, tamper and
routine supervisory signals to the control panel.
TriTech Motion Sensor
2.0 Specifications
• Coverage area 35 ft. by 35 ft. (10.7 m by 10.7 m).
• Internal coverage pointability -4° to -10° Vertical and ±10° Horizontal.
• Field selectable sensitivity options of Standard and the more sensitive
setting of Intermediate.
• Three minute transmitter lockout time after alarm extends battery life.
• Timed Walk Test Mode automatically disables LED after setup to
extend battery life.
General
• Dimensions ( H x W x D): 5 in. x 2.8 in. x 2.5 in.
(12.7 cm x 7.2 cm x 6.2 cm)
• Power supplied by four 1.5 V AAAlkaline batteries.
Recommended Batteries: PanasonicAM-3
Duracell MN1500 or PC1500
Energizer E91
• Cover activated Tamper indication. Optional wall-activated Tamper is
included.
• Typical current draw is 100 µA with the LED disabled. The LED is
automatically disabled except during walk tests.
RF Transmitter
• Typical battery life is two to three years.
• Operating temperature range of +32°F to +120°F (0°C to +49°C).
• Integral RF transmitter capable of transmitting up to 500 ft. (150 m) in
open air. (Actual acceptable transmitter range should be verified for
each installation). In normal operation, it is recommended that the
RF835 be within 100 ft. (30 m) of the receiver.
• Microwave Frequency: RF835E
RF835E-C 10.588 GHz
• RF Transmit Frequency: 433 MHz
10.525 GHz
• Transmits low battery reports and tamper reports to the control panel.
• Transmits supervisory signal to the control panel every 13 minutes.
• Options: B335 Low Profile Swivel Mount Bracket (use of this bracket
may reduce range and dead zone areas).
• Patents: This product is covered by one or more of the following U.S.
Patents: #4,660,024, #4,764,755, #5,077,548, #5,208,567,
#5,262,783, and #5,450,062. Other patents pending.
3.0 Installation
3.2 Avoid:
3.3 Observe Receiver Range.
3.1 Select a mounting location. Mount
the sensor where an intruder will
most likely cross through the
coverage pattern.
Mounting Outdoors
Moisture
Moving objects
500 ft. max
(150 m)
recommended
100 ft. (30 m)
Direct or
reflected
sunlight
Hot or cold air
directed onto
sensor
Panel Receiver
3.4 Observe the Pet Immunity mounting recommendations.
3.5 Remove the cover and the base.
Notch
NO
6.5 ft.
(2 m)
Insert a
flat-bladed
screwdriver into
notches and twist.
To avoid marring, use
a larger blade and
twist gently.
OK
NO
Don't point where
pets can climb
Mount the detector 6.5 ft.
(2 m) above the floor
Pet Immune Area
Note: The upper areas are
not pet immune.
Notches
3.6 Choose mounting height and desired range, and set the vertical angle.
For pet immune
applications, adjust
the angle to -5.0.
NOTE: The mounting
Range
Mounting
Vertical
Adjust
Screw
height must be
6.5 ft. (2 m) and
the vertical
Height
20 ft. (6.1 m)
35 ft. (10.7 m)
Loosen the
Vertical Adjust
Screw. Adjust the
board to the desired
angle.
6.5 ft. (2 m)
-7°
-9°
-5°
-6°
-7°
INT
- 6
- 10
angle must be
set at -5° for
installations
containing pets.
STD
-
6
- 10
7.0 ft. (2.1 m)
8.0 ft. (2.4 m)
MAX
MIN
MW
-10°
Download from Www.Somanuals.com. All Manuals Search And Download.
|