Application Note
BlueBox Demo-Board for the digital sensors
SMB365 (acceleration) and SMD500 (pressure)
Bosch Sensortec
AN18002
Installation and use of the BOSCH Sensortec
multi sensor, wireless Demo-Board
BlueBox V1.0
ABSTRACT
Based on the experience of 500 million MEMS sensors and testing to highest quality
standards, BOSCH Sensortec has developed a sensor family, consisting out of
pressure- and acceleration sensors with best-of-the-market performance and out-
standing reliability. Both the SMB365 acceleration sensor and the SMD500 pressure
sensor are specifically designed for digital low-power applications to enhance
functionality in consumer electronic devices as well as in health, logistics and security
systems. These sensors are available in small and thin standard packages
(QFN 4x4 mm² for acceleration and LCC8 5x5 mm² for pressure) to fit even into the
smallest, state-of-the-art devices.
This application note shows how to set up and how to install the SensorDesktop
software and the BlueBox hardware for functionality demonstration and some minor
evaluation purposes or application examples of the SMB365 and the SMD500 sensor.
The proper use and some general functions, e.g. wireless operation of the BlueBox
Demo-Board, are also described. For specific product evaluation refer to the BOSCH
Sensortec Evaluation Board which is especially designed for application engineering or
extensive testing purposes.
Discover more innovative perspectives for Life Sience and consumer applications:
Page 1
Rev. 1.0
© Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such
copying and passing onto third parties.
7211RB11.
Download from Www.Somanuals.com. All Manuals Search And Download.
Application Note
BlueBox Demo-Board for the digital sensors
SMB365 (acceleration) and SMD500 (pressure)
Bosch Sensortec
AN18002
Content
1
INTRODUCTION
4
1.1
1.1.1
1.1.2
1.2
BOARD OVERVIEW
5
6
6
7
Acceleration Part (SMB365)
Pressure Part (SMD500)
BOARD CONSTITUENTS
2
3
HARD- & SOFTWARE INSTALLATION
8
QUICK-START
17
3.1
3.2
3.3
3.3.1
3.3.2
3.3.3
USB WIRE BOUND
BLUETOOTH WIRELESS
CUSTOM CALIBRATION OF THE PRESSURE SENSOR SMD500
17
19
21
22
23
24
Calibrate at sea level (via internet)
Calibrate at sea level (manual)
Calibrate altitude (manual)
4
OPERATION
25
4.1
4.2
4.2.1
4.3
4.3.1
4.3.2
4.3.3
4.3.4
THE BLUEBOX COCKPIT WINDOW
THE BLUEBOX ALTIMETER WINDOW
Additional Plots and Altimeter Settings
THE BLUEBOX ACCELEROMETER WINDOW
25
27
29
33
35
36
37
40
42
SMB365 Normal-Power Mode
SMB365 Low-Power Mode in global interrupt conditions
SMB365 Low-Power Mode in independent interrupt conditions
SMB365 Selftest
4.4
SENSOR EVALUATION AND DIRECT DATA EXPORT
Page 3
Rev. 1.0
© Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such
copying and passing onto third parties.
7211RB11.
Download from Www.Somanuals.com. All Manuals Search And Download.
Application Note
BlueBox Demo-Board for the digital sensors
SMB365 (acceleration) and SMD500 (pressure)
Bosch Sensortec
AN18002
1
Introduction
Sensors from Bosch Sensortec provide many capabilities for consumer products, offering a
wide range of new functions. By measuring acceleration, pressure and angular rate, they make
operating devices simpler and more intuitive. BOSCH Sensortec MEMS sensors also contribute
to more efficient medical care. Devided into acceleration and pressure sensing, the applications
are typically realized in the fields of
Acceleration Sensing
•
•
•
•
•
•
•
•
•
•
•
Mobile phones and PDAs
Portable music players
Toys and gaming
Portable city- and outdoor navigation
Leisure and sports
Camera and video equipment
Mobile computing
Security systems
Health
Home appliances
Logistics
Pressure Sensing:
•
•
•
•
•
•
Portable city- and outdoor navigation
Dead reckoning
Leisure and sports
Weather forecast
Vertical velocity indication (rise / sink speed)
Security systems
Page 4
Rev. 1.0
© Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such
copying and passing onto third parties.
7211RB11.
Download from Www.Somanuals.com. All Manuals Search And Download.
Application Note
BlueBox Demo-Board for the digital sensors
SMB365 (acceleration) and SMD500 (pressure)
Bosch Sensortec
AN18002
1.1 Board overview
+Z
+Y
+X
SMD500
SMB365
[1.1] BlueBox overview including axes alignment for SMB365 acceleration sensor
The Bosch Sensortec BlueBox Demo-Board in combination with its SensorDesktop software
was built for the simultaneous demonstration of the general functionality of the digital
accelerometer sensor SMB365 and the digital pressure sensor SMD500. This includes the
possibility of demonstrating output signal behaviors of each sensor as graphical functions,
interrupt features different power modes, threshold and hysteresis limits, different acceleration
or pressure ranges, the self test function, as well as a user defined direct data export. All either
wire bound via USB or wireless via Bluetooth. Note that the Bosch BlueBox Demo-Board should
not be considered as an evaluation tool. For specific product evaluation refer to the
corresponding BOSCH Evaluation Kits.
After a simple installation of the SensorDesktop software and the connection of the demo board
to a free USB port acceleration specific signals corresponding e.g. to tilt, movement, free-fall,
vibration, shock as well as pressure specific signals corresponding e.g. to height, atmospheric
Page 5
Rev. 1.0
© Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such
copying and passing onto third parties.
7211RB11.
Download from Www.Somanuals.com. All Manuals Search And Download.
Application Note
BlueBox Demo-Board for the digital sensors
SMB365 (acceleration) and SMD500 (pressure)
Bosch Sensortec
AN18002
or differential pressure, change in weather and many more can all be measured and visualized
in real-time.
1.1.1 Acceleration Part (SMB365)
In order to measure the above mentioned acceleration specific signals, the BlueBox demo
board is equipped with the Bosch Sensortec SMB365 acceleration sensor. This digital, triaxial
accelerometer, on the basis of the differential capacitive principle, is able to measure low gravity
accelerations in two ranges (±2g and ±10g full scale) in all 3 directions in space, the X, Y and Z
direction with a resolution of 0.004g in the low g range. The alignment of the positive X, Y and Z
direction according to the acceleration sensor is described in the illustration [1.1] above. The
SMB365 is based on automotive proven Robert Bosch technology for silicon surface micro-
machining processes. This has been proven in more than 200 million Bosch accelerometers so
far.
1.1.2 Pressure Part (SMD500)
Additionally to the accelerometer, the BlueBox board is equipped with another Bosch Sensortec
product, the SMD500 pressure sensor, which marks a new generation of high precision digital
pressure sensors for consumer applications. The SMD500 is based on piezoresistive
technology for EMC robustness, high accuracy and linearity as well as long term stability. Its
ultra low-power, low voltage electronics are optimized for use in mobile phones, PDAs, GPS
devices and outdoor equipment. With an altitude noise down to 0.03 hPa (0.25 m) it offers
superior performance in a measurement range from 300 to 1100 hPa (+9000 to -500 m).
For detailed information please refer to the SMB365 and SMD500 related data sheets.
Page 6
Rev. 1.0
© Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such
copying and passing onto third parties.
7211RB11.
Download from Www.Somanuals.com. All Manuals Search And Download.
Application Note
BlueBox Demo-Board for the digital sensors
SMB365 (acceleration) and SMD500 (pressure)
Bosch Sensortec
AN18002
1.2
Board constituents
The following illustration describes the main elements of the BlueBox multi sensor demo board.
Main components are:
Number
Component
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
Bluetooth unit
Bosch Sensortec SMB365 acceleration sensor
Vreg Voltage Regulator and VShift Logic Level Shifter
Microcontroller Programming Interface
8bit Microcontroller
Converter ASIC; Bit Parallel to USB
Bosch Sensortec SMD500 pressure sensor
Data Transmission and Control LED‘s
USB I/O Port
On/Off switch
4
1
8
6
9
5
3
2
10
7
3
3
Page 7
Rev. 1.0
© Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such
copying and passing onto third parties.
7211RB11.
Download from Www.Somanuals.com. All Manuals Search And Download.
Application Note
BlueBox Demo-Board for the digital sensors
SMB365 (acceleration) and SMD500 (pressure)
Bosch Sensortec
AN18002
2
Hard- & Software Installation
1. Insert SensorDesktop-CD
2. Run “setup.exe” from the directory …:\ SensorDesktop _DemoSoftware
3. The following message box appears
4. Click “Next”
5. The following message box appears
6. Select the primary installation directories “BST_SensorDesktop” and “National
Instruments” in the user specific directory “Program Files” (drive may vary from C:\)
7. The following message box appears
Page 8
Rev. 1.0
© Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such
copying and passing onto third parties.
7211RB11.
Download from Www.Somanuals.com. All Manuals Search And Download.
Application Note
BlueBox Demo-Board for the digital sensors
SMB365 (acceleration) and SMD500 (pressure)
Bosch Sensortec
AN18002
8. Accept the License Agreement(s) as described above.
9. Click “Next”
10. The following message box appears
11. Confirm installation by clicking on “Next”
12. While the installation is in progress, the following message box appears
Page 9
Rev. 1.0
© Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such
copying and passing onto third parties.
7211RB11.
Download from Www.Somanuals.com. All Manuals Search And Download.
Application Note
BlueBox Demo-Board for the digital sensors
SMB365 (acceleration) and SMD500 (pressure)
Bosch Sensortec
AN18002
13. Wait until the installation is finished
14. When the installation of SensorDesktop is finished, the following message box appears
15. Click finish and restart computer if necessary
Page 10
Rev. 1.0
© Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such
copying and passing onto third parties.
7211RB11.
Download from Www.Somanuals.com. All Manuals Search And Download.
Application Note
BlueBox Demo-Board for the digital sensors
SMB365 (acceleration) and SMD500 (pressure)
Bosch Sensortec
AN18002
16. After restarting the computer, connect the BlueBox demo board to a free USB port
17. Turn on the BlueBox (main switch on the board into the direction to the USB connector)
18. The following message boxes appears
19. Click “Next”
20. The following message box appears
21. Install Hardware Device Drivers by recommended selection as described above
22. Click “Next”
Page 11
Rev. 1.0
© Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such
copying and passing onto third parties.
7211RB11.
Download from Www.Somanuals.com. All Manuals Search And Download.
Application Note
BlueBox Demo-Board for the digital sensors
SMB365 (acceleration) and SMD500 (pressure)
Bosch Sensortec
AN18002
23. The following message box appears
24. Locate Files by selecting “CD-ROM drives” and “Specify a location” as described above
25. Click “Next”
26. The following message box appears
27. Make sure that the correct CD-ROM is inserted and confirm by clicking “OK”
28. Select “FTDIBUS.INF” as Hardware Device Driver
29. Click “Open”
Page 12
Rev. 1.0
© Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such
copying and passing onto third parties.
7211RB11.
Download from Www.Somanuals.com. All Manuals Search And Download.
Application Note
BlueBox Demo-Board for the digital sensors
SMB365 (acceleration) and SMD500 (pressure)
Bosch Sensortec
AN18002
30. If driver file has been successfully found, the following message box appears
31. Confirm the selection by clicking “Next”
32. If the driver file has been successfully installed, the following message box appears
33. Click “Finish” to complete the FTDIBUS.INF Device Driver installation
Page 13
Rev. 1.0
© Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such
copying and passing onto third parties.
7211RB11.
Download from Www.Somanuals.com. All Manuals Search And Download.
Application Note
BlueBox Demo-Board for the digital sensors
SMB365 (acceleration) and SMD500 (pressure)
Bosch Sensortec
AN18002
34. After finishing of the FTDIBUS.INF Device Driver installation the following message
boxes appears
35. Click “Next”
36. The following message box appears
37. Install Hardware Device Drivers by recommended selection as described above
38. Click “Next”
Page 14
Rev. 1.0
© Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such
copying and passing onto third parties.
7211RB11.
Download from Www.Somanuals.com. All Manuals Search And Download.
Application Note
BlueBox Demo-Board for the digital sensors
SMB365 (acceleration) and SMD500 (pressure)
Bosch Sensortec
AN18002
39. The following message box appears
40. Locate Files by selecting “CD-ROM drives” and “Specify a location” as described above
41. Click “Next”
42. The following message box appears
43. Make sure that the correct CD-ROM is inserted and confirm by clicking “OK”
44. Select “FTDIPORT.INF” as Hardware Device Driver
45. Click “Open”
Page 15
Rev. 1.0
© Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such
copying and passing onto third parties.
7211RB11.
Download from Www.Somanuals.com. All Manuals Search And Download.
Application Note
BlueBox Demo-Board for the digital sensors
SMB365 (acceleration) and SMD500 (pressure)
Bosch Sensortec
AN18002
46. If the driver file has been successfully found, the following message box appears
47. Confirm the selection by clicking “Next”
48. If the driver file has been successfully installed, the following message box appears
49. Click “Finish” to complete the Device Driver installation
Page 16
Rev. 1.0
© Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such
copying and passing onto third parties.
7211RB11.
Download from Www.Somanuals.com. All Manuals Search And Download.
Application Note
BlueBox Demo-Board for the digital sensors
SMB365 (acceleration) and SMD500 (pressure)
Bosch Sensortec
AN18002
3
Quick-Start
Note: It is strongly recommended that the BST Sensor Desktop software is already installed on
your PC before continuing with the following chapters.
3.1 USB wire bound
1. Turn on the BlueBox demo board (Main Switch into the direction of the USB connector)
o The demo board performs a self test indicated as a LED light up sequence
o LEDs in general from left to right:
- outer red: (flashes) battery warning
- yellow: (constant) continuous data transmission
- green: (constant) logic COM port connection
- yellow: (alternately flashes with green LED) searching COM port
- inner red: (constant) recharging battery
USB connector
Main Switch
LEDs
2. Connect the BlueBox to a free USB-Port on your PC
o the red LED on the board indicates: “recharging battery pack”, used for optional
wireless operation, the green LED indicates “logic connection to COM port O.K.”
3. Execute the SensorDesktop software on the PC from Start\Programs\ SensorDesktop
Page 17
Rev. 1.0
© Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such
copying and passing onto third parties.
7211RB11.
Download from Www.Somanuals.com. All Manuals Search And Download.
Application Note
BlueBox Demo-Board for the digital sensors
SMB365 (acceleration) and SMD500 (pressure)
Bosch Sensortec
AN18002
4. After starting the software, the cockpit window of the BlueBox software appears. The
software tries to locate automatically the corresponding COM port of the demo board. If
the demo board is located, a status message at the bottom left hand corner of the
software window will indicate to which COM port the module is connected. If the status
window indicates “Module not found” the board has to be located manual. Only in this
case click on “File” Æ “Detect Module on COM Port” in the status bar.
Select „File“ Æ “Detect Module on COM Port” for manual COM port location
Start data acquisition
Status window
5. Press the „Start“ button to start data acquisition of acceleration and pressure sensor
6. Accelerate, roll, tilt or lift the BlueBox board
7. Watch the graphs in the different displays on the cockpit screen
o Note: For exact altimeter response it is strongly recommended to correct the
ambient air pressure data before further using the board (see chapter 3.3)
Page 18
Rev. 1.0
© Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such
copying and passing onto third parties.
7211RB11.
Download from Www.Somanuals.com. All Manuals Search And Download.
Application Note
BlueBox Demo-Board for the digital sensors
SMB365 (acceleration) and SMD500 (pressure)
Bosch Sensortec
AN18002
3.2 Bluetooth wireless
1. Make sure that the used PC or laptop supports Bluetooth capability.
2. Make sure that system specific Bluetooth hard- and software as well as drivers are
installed and activated.
3. Before using wireless data transmission via Bluetooth start up the BlueBox once
according to chapter 3.1 and let the BlueBox connected at least 5 hours to fully charge
the battery pack.
Main Switch
Bluetooth Device ID
Bluetooth unit
4. Double Click on the Bluetooth symbol
in the system tray or start your Bluetooth
software to set up the correct Bluetooth environment for the BlueBoard.
o Bluetooth software must support SPP Protocoll (Serial Port Profile) and virtual
serial COM port respectively
o Configure according to “Pair Devices” or “Pairing”
5. Turn on the BlueBox demo board (USB cable disconnected) for wireless use
6. Search for the corresponding Bluetooth Device ID in Bluetooth environment
in this example “7763” according to the illustration above
o When asked for Bluetooth Pin or Key enter “0000”
8. Execute the SensorDesktop software on the PC from Start\Programs\ SensorDesktop
Page 19
Rev. 1.0
© Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such
copying and passing onto third parties.
7211RB11.
Download from Www.Somanuals.com. All Manuals Search And Download.
Application Note
BlueBox Demo-Board for the digital sensors
SMB365 (acceleration) and SMD500 (pressure)
Bosch Sensortec
AN18002
9. After starting the software, the cockpit window of the BlueBox software appears. The
software tries to locate automatically the corresponding virtual COM port of the demo
board. If the demo board is located, a status message at the bottom left hand corner of
the software window will indicate, to which COM port the module is connected. If the
status window indicates “Module not found” the board has to be located manually. Only
in this case click on “File” Æ “Detect Module on COM Port” in the status bar.
Select „File“ Æ “Detect Module on COM Port” for manually COM port location
Start data acquisition
Status window
10. Press the „Start“ button to start data acquisition of acceleration and pressure sensor
11. Accelerate, roll, tilt or lift the BlueBox board
12. Watch the graphs in the different displays on the cockpit screen
o Note: For exact altimeter response it is strongly recommended to correct the
ambient air pressure data before further using the board (see chapter 3.3)
Page 20
Rev. 1.0
© Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such
copying and passing onto third parties.
7211RB11.
Download from Www.Somanuals.com. All Manuals Search And Download.
Application Note
BlueBox Demo-Board for the digital sensors
SMB365 (acceleration) and SMD500 (pressure)
Bosch Sensortec
AN18002
3.3 Custom calibration of the SMD500 altimeter function
With the SMD500, there is the possibility to precisely measure the ambient air- or atmospheric
pressure. According to the international barometric formula it is possible to determine the
current altitude out of the measured atmospheric pressure. Before using the SMD500 on the
BlueBox multi sensor demo board for exact altitude measurements, some facts are good to
know:
The ambient air- or atmospheric pressure is a typical weather and temperature related
phenomena. As a law of nature, the atmospheric pressure varies in a certain range over the day
and can be referred in two ways. Either to the ambient (as is) pressure, including the actual
position altitude or to the pressure at sea level (virtual), excluding the altitude of the actual
position. This “virtual” or “re-calculated” pressure, the so called pressure at sea level, always
refers to the height of “zero” above sea level. According to the international barometric formula
mentioned above, altitude (h) in meter, atmospheric pressure (p) and pressure at sea level (p0)
can be related as followed:
1
⎛
⎞
⎟
5.255
⎜
⎛
⎞
p
⎜
⎜
⎟
⎟
h = 44262.7 ⋅ 1-
h in meter
⎜
⎟
p0
⎝
⎠
⎜
⎝
⎟
⎠
According to the formula above, the SMD500 always measures precisely the absolute
atmospheric pressure, including height, temperature and weather effects. In combination with
the pressure at sea level, it is possible e.g. to determine the altitude. For accurate altitude
measurements, using the SMD500 on the BlueBox demo board, it is necessary to recalibrate
the board at least once a day. For an exact altitude measurement we recommend to calibrate
the board straight before the measurement.
Generally, there are three possibilities for a calibration. On the one hand, if the exact sea level
pressure is known or possible to get (e.g. from internet or a nearby airport), there is the
possibility to “calibrate at sea level” either “via internet” or “manual”. On the other hand, if the
exact altitude is known, there is the possibility for a calibration using the function “calibrate
altitude”.
Page 21
Rev. 1.0
© Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such
copying and passing onto third parties.
7211RB11.
Download from Www.Somanuals.com. All Manuals Search And Download.
Application Note
BlueBox Demo-Board for the digital sensors
SMB365 (acceleration) and SMD500 (pressure)
Bosch Sensortec
AN18002
3.3.1 Calibrate at sea level via internet
This function applies to altitude measurements under a known sea level pressure obtained from
the internet.
1. Open Settings Æ Calibrate at sea level
2. Chose “via internet tab” [a]
a
b
c
d
e
f
3. Connect the PC to the internet
4. Select the nearby location from the default list [b]
o location in default list should be < 200 km off current location
o if current location is > 200 km in distance calibrate according chapter 3.3.2
5. Choose the unit [c]
6. Press “get pressure at sea level” [d] for pressure at sea level update
7. Confirm with OK [e] or cancel [f] selection
Page 22
Rev. 1.0
© Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such
copying and passing onto third parties.
7211RB11.
Download from Www.Somanuals.com. All Manuals Search And Download.
Application Note
BlueBox Demo-Board for the digital sensors
SMB365 (acceleration) and SMD500 (pressure)
Bosch Sensortec
AN18002
3.3.2 Calibrate at sea level manually
This function applies to altitude measurements under a known and manually obtained sea level
pressure.
1. Open Settings Æ Calibrate at sea level
2. Choose “manual tab” [a]
a
b
c
d
e
3. Obtain current pressure at sea level
o E.g. from local weather service or nearby airport
4. Choose corresponding unit [b]
5. Put in the pressure value [c]
6. Confirm with OK [d] or cancel [e] selection
Page 23
Rev. 1.0
© Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such
copying and passing onto third parties.
7211RB11.
Download from Www.Somanuals.com. All Manuals Search And Download.
Application Note
BlueBox Demo-Board for the digital sensors
SMB365 (acceleration) and SMD500 (pressure)
Bosch Sensortec
AN18002
3.3.3 Calibrate altitude manually
This function applies to pressure measurements under a known and manually obtained altitude
1. Open Settings Æ Calibrate altitude
2. the following message box appears
a
d
b
c
3. Obtain actual altitude above sea level
o E.g. from map with altitude details, travel guide or internet
4. Choose corresponding unit [a]
5. Put in the altitude value [b]
6. Confirm with OK [c] or cancel [c] selection
Page 24
Rev. 1.0
© Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such
copying and passing onto third parties.
7211RB11.
Download from Www.Somanuals.com. All Manuals Search And Download.
Application Note
BlueBox Demo-Board for the digital sensors
SMB365 (acceleration) and SMD500 (pressure)
Bosch Sensortec
AN18002
4
Operation
4.1 The BlueBox Cockpit Window
The following figure gives an overview of the BlueBox Cockpit Window
1
2
3
4
6
7
8
9
5
1. Cockpit Tab
2. Acceleration display (SMB365)
•
•
•
•
•
Display shows output signals of all 3 axes (X, Y, Z) of the SMB365 in g
1 g corresponds to an acceleration of approximately 9,81 m/s²
The abscissa (x-coordinate) corresponds to time in seconds
The ordinate (y-coordinate) corresponds to acceleration in g
The ordinate features custom Min/Max scaling (± 2g full scale in low g mode)
Page 25
Rev. 1.0
© Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such
copying and passing onto third parties.
7211RB11.
Download from Www.Somanuals.com. All Manuals Search And Download.
Application Note
BlueBox Demo-Board for the digital sensors
SMB365 (acceleration) and SMD500 (pressure)
Bosch Sensortec
AN18002
3. Altitude Display (SMD500)
•
•
The display shows the primary output signal of the SMD500 converted to altitude
8.5 m differential height corresponds to an differential pressure of about 1 hPa
pressure at sea level
•
•
•
The abscissa (x-coordinate) corresponds to time in seconds
The ordinate (y-coordinate) corresponds to altitude in meter or feet
The ordinate features custom min/max scaling
4. Yaw Display (SMG300)
•
Disabled on BlueBord V1.0
5. COM Port Status Window
•
Indicates connection status of the BlueBoard demo board
6. Temperature Display (SMD500)
•
Display shows temperature as a secondary output signal of the SMD500 in °C,
°F or K (details see chapter 4.2 [18] )
•
•
•
The abscissa (x-coordinate) corresponds to time in seconds
The ordinate (y-coordinate) corresponds to the temperature in °C, °F or K
The ordinate features custom min/max scaling
7. Pressure Display (SMD500)
•
•
•
•
•
Display shows the primary output signal of the SMD500 in hPa, PSI or mm Hg
1hPa is equal to a pressure of 1mbar
The abscissa (x-coordinate) corresponds to time in seconds
The ordinate (y-coordinate) corresponds to absolute pressure in hPa, PSI or mm Hg
The ordinate features custom min/max scaling
8. Start button
•
To start data acquisition of acceleration- and pressure sensor output signals
9. Stop button
•
To end data acquisition of acceleration- and pressure sensor output signals
Page 26
Rev. 1.0
© Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such
copying and passing onto third parties.
7211RB11.
Download from Www.Somanuals.com. All Manuals Search And Download.
Application Note
BlueBox Demo-Board for the digital sensors
SMB365 (acceleration) and SMD500 (pressure)
Bosch Sensortec
AN18002
4.2 The BlueBox Altimeter Window
The following figure gives an overview of the BlueBox Altimeter Window
10
11
12
17
18
14
15
13
16
19
8
9
5
10. Altimeter Tab
11. absolute pressure
•
•
Display shows the absolute pressure in hPa, PSI or mm Hg
hPa, PSI and mm Hg can be converted as followed:
o PSI = hPa * 0.01450377
o mm Hg = hPa / 1.333224
o hPa = PSI / 0.01450377
o mm Hg = PSI * 51.71496
o hPa = PSI / 0.01450377
o mm Hg = hPa * 1.333224
Page 27
Rev. 1.0
© Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such
copying and passing onto third parties.
7211RB11.
Download from Www.Somanuals.com. All Manuals Search And Download.
Application Note
BlueBox Demo-Board for the digital sensors
SMB365 (acceleration) and SMD500 (pressure)
Bosch Sensortec
AN18002
12. absolute altitude above sea level
•
•
Display shows the absolute altitude above sea level in meter or feet
the absolute altitude in meter is calculated according to the international
barometric formula (see chapter 3.3)
•
meter and feet can be converted as followed:
o meter = feet / 0.3048
o feet = meter * 0.3048
13. Altimeter gauge
•
Display shows the calculated altitude in the meter or feet
14. digital value pressure
•
Display shows digital output pressure value of the SMD500 in LSB
15. pressure at sea level
•
Display shows the pressure at sea level in hPa, PSI or mm Hg
16. Barometer gauge
•
Display shows the pressure at sea level in hPa, PSI and mm Hg
17. digital value temperature
•
Display shows digital output temperature value of the SMD500 in LSB
18. Temperature
•
•
Display shows the calculated temperature value in °C, °F or K
Fahrenheit, Kelvin and Celsius can be converted as followed:
o °F = °C * 1.8 + 32
o K = °C + 273.15
o °C = (°F - 32) / 1,8
o K = °F + 459.67 / 1.8
o °C = K - 273.15
o °F = K *1.8 - 459.67
19. Thermometer gauge
Display shows the calculated temperature value in °C and °F
•
Page 28
Rev. 1.0
© Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such
copying and passing onto third parties.
7211RB11.
Download from Www.Somanuals.com. All Manuals Search And Download.
Application Note
BlueBox Demo-Board for the digital sensors
SMB365 (acceleration) and SMD500 (pressure)
Bosch Sensortec
AN18002
4.2.1 Additional Plots and Altimeter Settings
Plots
For a more detailed view of the SMD500 related signal outputs there is the possibility to express
the data (altitude, pressure, temperature) in additional plots as followed:
1. Open plots Æ View graphs
2. The following plot box appears
Page 29
Rev. 1.0
© Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such
copying and passing onto third parties.
7211RB11.
Download from Www.Somanuals.com. All Manuals Search And Download.
Application Note
BlueBox Demo-Board for the digital sensors
SMB365 (acceleration) and SMD500 (pressure)
Bosch Sensortec
AN18002
3. Edit or customize plot box view
•
Three plots will be generated
o Altitude, Pressure and Temperature
All three plots offer automatically scaling of the y-axis
In general there are 2 views possible
•
•
o Rolling graphs with 30 minutes (Yes or No)
o Rolling only effects data of > 30 min sampling time
o The two views are not reversible, if changed after 30 minutes
Rolling graphs with 30 minutes: YES
•
•
o After 30 minutes the measurement starting point will be scrolled
o There will be only the last 30 minutes of measurement data visible
Rolling graphs with 30 minutes: NO
o After 30 minutes the time scale will be scaled
o All measurement data will be visible according to the new time scale
Page 30
Rev. 1.0
© Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such
copying and passing onto third parties.
7211RB11.
Download from Www.Somanuals.com. All Manuals Search And Download.
Application Note
BlueBox Demo-Board for the digital sensors
SMB365 (acceleration) and SMD500 (pressure)
Bosch Sensortec
AN18002
Settings Æ Measurements
According to customized settings (high signal resolution or low power consumption) it is
possible to choose different sample averaging numbers and update rates. E.g. increasing the
resolution leads to a decreased noise with increased power consumption and contrariwise. This
behavior can be edited by the following:
4. Open Settings Æ Measurements
5. The following message box appears
6. Chose sampling average number and update rate according to the text
•
•
•
sampling average number = Number of single values for avg. calculation
o edit by mouse scroll
update rate = time for a new “send data command”
o Minimum update rate 0.5 s
sample rate = update rate / sampling average number
o Minimum sampling rate 0.1 s
o Maximum 2 values per second (2 Hz) possible
Page 31
Rev. 1.0
© Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such
copying and passing onto third parties.
7211RB11.
Download from Www.Somanuals.com. All Manuals Search And Download.
Application Note
BlueBox Demo-Board for the digital sensors
SMB365 (acceleration) and SMD500 (pressure)
Bosch Sensortec
AN18002
Settings Æ Display PROM Data
For some basic evaluation purposes, there is the possibility to display the stored SMD500
PROM data.
1. Open Settings Æ Display PROM data
2. The following message box appears
3. It is possible to manually view the stored data:
•
AC1 to AC6 are the calibration coefficients expressed as raw data
o varying form 9 to 14 bit words
•
F1 to F4 are shifted calibration coefficients
o shifted to generate 4 uniform 16 bit words containing the 6 AC
coefficients
Page 32
Rev. 1.0
© Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such
copying and passing onto third parties.
7211RB11.
Download from Www.Somanuals.com. All Manuals Search And Download.
Application Note
BlueBox Demo-Board for the digital sensors
SMB365 (acceleration) and SMD500 (pressure)
Bosch Sensortec
AN18002
4.3 The BlueBox Accelerometer Window
The following figure gives an overview of the BlueBox Accelerometer Window
20
21
22
26
23
27
28
29
30
24
25
8
9
5
20. Sensor Mode selection
•
•
•
Normal Power for full performance mode (10bit resolution)
Low Power for interrupt mode (7bit resolution)
Standby for energy saving mode (0bit resolution)
21. Acceleration range selection
•
•
± 2g for low g applications
± 10g for high g applications
22. Interrupt mode selection
•
•
global interrupt conditions (same for all axes)
independent interrupt conditions (individual for each axis)
Page 33
Rev. 1.0
© Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such
copying and passing onto third parties.
7211RB11.
Download from Www.Somanuals.com. All Manuals Search And Download.
Application Note
BlueBox Demo-Board for the digital sensors
SMB365 (acceleration) and SMD500 (pressure)
Bosch Sensortec
AN18002
23. Hysteresis and Threshold level settings
•
for global interrupt conditions
o Threshold and Hysteresis for all axes are given in digits (d) of a 7bit word
o 1d corresponds to 4 LSB (16mg in low g mode and 0.08g in high g mode)
for axis individual interrupt conditions
•
o Threshold for each axis is given in digits (d) of a 5bit word
o 1d corresponds to 16 LSB (64mg in low g mode and 0.32g in high g mode)
o Hysteresis for each axis is given in digits (d) of a 3 bit word
o 1d corresponds to 64 LSB (256mg in low g mode and 1.28g in high g mode)
24. Selftest selection
•
Off/On (disable/enable) selftest to check signal evaluation path (MEMS plus ASIC)
25. Interrupt signal output LED
•
•
LED off = interrupt inactive; LED on = interrupt active
No software-function but direct readout of the SMB365 internal interrupt logic pin
26. Acceleration signal output screen
•
•
Acceleration sensitive digital signal, given in LSB, g or m/sec²
1LSB corresponds to 4mg in low g mode and 20mg in high g mode
27. Ordinate unit selection (acceleration)
•
choose proper unit of acceleration sensor output signal (g, m/s² or LSB)
28. Output signal reference color
•
X-axis = green
Y-axis = yellow
Z-Axis = red
29. Ordinate scale selection (acceleration)
•
•
full scale: ±512LSB, ±20m/s² or ±2g in 2 g range (resolution: 1LSB = 4mg)
full scale: ±512LSB, ±100m/s² or ±10g in 10g range (resolution: 1LSB = 20mg)
30. Abscissa scale selection (timebase)
select from 2000 to 50 msec/div
•
Page 34
Rev. 1.0
© Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such
copying and passing onto third parties.
7211RB11.
Download from Www.Somanuals.com. All Manuals Search And Download.
Application Note
BlueBox Demo-Board for the digital sensors
SMB365 (acceleration) and SMD500 (pressure)
Bosch Sensortec
AN18002
4.3.1 SMB365 Normal-Power Mode
Software and sensor offer the following features
•
•
•
•
Full performance (10bit resolution)
Two selectable acceleration ranges: 2g and 10g
Full selftest capability (see chapter 4.3.4)
No interrupt functionality
20
21
22
26
23
27
28
29
30
24
25
8
9
5
How to set up the SMB365 in Normal-Power mode:
•
•
•
•
Select Normal-Power Mode [20]
Select any acceleration range [21]
Scale ordinate [27], [29] and abscissa [30]
Start and stop data acquisition [8], [9] or activate self test [24] during data acquisition
Page 35
Rev. 1.0
© Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such
copying and passing onto third parties.
7211RB11.
Download from Www.Somanuals.com. All Manuals Search And Download.
Application Note
BlueBox Demo-Board for the digital sensors
SMB365 (acceleration) and SMD500 (pressure)
Bosch Sensortec
AN18002
4.3.2 SMB365 Low-Power Mode in global interrupt conditions
Software and sensor offer the following features
•
•
•
•
•
•
Interrupt functionality, e.g. for free-fall demonstration
Increased acceleration output signal speed
Reduced power consumption (20%)
Reduced acceleration output signal resolution (7bit)
Two selectable acceleration ranges: 2g and 10g
Individual settings for global interrupt:
o Threshold (7bit): 1d = 4LSB (16mg in 2g mode and 0.08g in 10g mode)
o Hysteresis (7bit): 1d = 4LSB (16mg in 2g mode and 0.08g in 10g mode)
Full selftest capability (see chapter 4.3.4)
•
20
21
22
26
23
27
28
29
30
24
25
8
9
5
How to set up the SMB365 in global interrupt conditions:
Page 36
Rev. 1.0
© Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such
copying and passing onto third parties.
7211RB11.
Download from Www.Somanuals.com. All Manuals Search And Download.
Application Note
BlueBox Demo-Board for the digital sensors
SMB365 (acceleration) and SMD500 (pressure)
Bosch Sensortec
AN18002
•
•
•
•
•
•
Select Low-Power Mode [20]
Select any acceleration range [21]
Select Global Interrupt Mode [22]
Put in global Hysteresis and Threshold digits [23]
Start data acquisition [8]
Accelerate, roll or tilt the BlueBox board while watching the interrupt LED [25]
Notes:
The triggering of an interrupt depends, in the first instance, on global Threshold value settings.
The global Threshold can be assumed as the interrupt “switch-on” level which must be
exceeded from at least one axis dependent acceleration signal. If any acceleration signal
exceeds this value, an interrupt will be activated. If all signals are below the Threshold value
again, the interrupt will be deactivated, provided that the Hysteresis value is set to zero, e.g.:
LED [25] = 1 if LSBX > Threshold OR LSBY > Threshold OR LSBZ > Threshold
LED [25] = 0 if LSBX < Threshold AND LSBY < Threshold AND LSBZ < Threshold
In addition to the global Threshold value a global Hysteresis value can also be set. The
Hysteresis can be assumed as the interrupt “switch-off” level, which must be under-run again
from all signals, to deactivate the triggered interrupt. It relates directly to the before set
Threshold value by a mathematical subtraction. The following example shows how to set up the
global Threshold and Hysteresis values. The calculation corresponds to the 2g operation mode,
e.g.:
LED [25] = 1 if LSBX > Threshold OR LSBY > Threshold OR LSBZ > Threshold
LED [25] = 0 if LSBX < Hysteresis AND LSBY < Hysteresis AND LSBZ < Hysteresis
Threshold:
Hysteresis:
75d = 75⋅ 4LSB = 300LSB
∝
∝
75⋅16mg =1.2g
25d = 300LSB − 25⋅ 4LSB = 200LSB
1.2g − 25⋅16mg = 0.8g
If Hysteresis is equal or above Threshold, the interrupt functionality will be disabled. For a total
reset of the sensor internal interrupt information just switch to standby mode [20] and continue.
4.3.3 SMB365 Low-Power Mode in independent interrupt conditions
Software and sensor offer the following features
Page 37
Rev. 1.0
© Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such
copying and passing onto third parties.
7211RB11.
Download from Www.Somanuals.com. All Manuals Search And Download.
Application Note
BlueBox Demo-Board for the digital sensors
SMB365 (acceleration) and SMD500 (pressure)
Bosch Sensortec
AN18002
•
•
•
•
•
Interrupt functionality, e.g. for theft protection
Reduced power consumption (20%)
Reduced acceleration output signal resolution (7 bit)
Two selectable acceleration ranges: 2g and 10g
Individual interrupt settings for each axis:
o Threshold (5 bit): 1d = 16LSB (64mg in 2g mode and 0.32g in 10g mode)
o Hysteresis (3 bit): 1d = 64LSB (256mg in 2g mode and 1.28g in 10g mode)
Full selftest capability (see chapter 4.3.4)
•
20
21
22
26
23
27
28
29
30
24
25
8
9
5
How to set up the SMB365 in axis independent interrupt conditions:
•
Select Low-Power Mode [20]
Page 38
Rev. 1.0
© Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such
copying and passing onto third parties.
7211RB11.
Download from Www.Somanuals.com. All Manuals Search And Download.
Application Note
BlueBox Demo-Board for the digital sensors
SMB365 (acceleration) and SMD500 (pressure)
Bosch Sensortec
AN18002
•
•
•
•
•
Select any acceleration range [21]
Select independent interrupt mode [22]
Put in Hysteresis and Threshold digits for X, Y and Z axis [23]
Start data acquisition [8]
accelerate, roll or tilt the TriBox board while watching the interrupt LED [25]
For Interrupt operation as a function of Threshold and Hysteresis the same as shown in chapter
4.3.2 before applies with one exception. Threshold and Hysteresis can be selected individually
for each axis. For Hysteresis set = Zero, the following logic applies, e.g.:
LED [25] = 1 if LSBX > ThresholdX OR LSBY > ThresholdY OR LSBZ > ThresholdZ
LED [25] = 0 if LSBX < ThresholdX AND LSBY < ThresholdY AND LSBZ < ThresholdZ
For Hysteresis set ≠ Zero, the following logic applies, e.g.:
LED [25] = 1 if LSBX > ThresholdX OR LSBY > ThresholdY OR LSBZ > ThresholdZ
LED [25] = 0 if LSBX < HysteresisX AND LSBY < HysteresisY AND LSBZ < HysteresisZ
The following example shows how to set up the axis specific Threshold and Hysteresis. The
calculation corresponds to the low g operation mode:
Threshold:
20d = 20⋅16LSB = 320LSB
∝
20⋅64mg = 1.28g
Hysteresis: 1d = 320LSB −1⋅64LSB = 256LSB ∝
1.28g −1⋅ 256mg = 1.02g
If Hysteresis is equal or above Threshold (LSB values), the interrupt functionality will be
disabled. For a total reset of the sensor internal interrupt information just switch to standby
mode [20] and continue.
Page 39
Rev. 1.0
© Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such
copying and passing onto third parties.
7211RB11.
Download from Www.Somanuals.com. All Manuals Search And Download.
Application Note
BlueBox Demo-Board for the digital sensors
SMB365 (acceleration) and SMD500 (pressure)
Bosch Sensortec
AN18002
4.3.4 SMB365 Selftest
All operation modes of the SMB365 sensor (2g, 10g, normal power, low-power, global and
independent interrupt condition) offer full on-chip selftest capability. The selftest acts on all three
axes to check all signal evaluation paths of the MEMS simultaneously. This includes the silicon
sensing element as well as the ASIC itself. The selftest is realized by a physical deflection of the
seismic mass due to an electrostatic force. In operation, it is possible to perform the selftest at
any time over the complete life cycle. For more details please refer to the latest sensor related
datasheet.
20
21
falling edge
rising edge
22
23
26
Selftest deactivated
Selftest activated
27
28
29
30
24
25
8
9
5
Page 40
Rev. 1.0
© Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such
copying and passing onto third parties.
7211RB11.
Download from Www.Somanuals.com. All Manuals Search And Download.
Application Note
BlueBox Demo-Board for the digital sensors
SMB365 (acceleration) and SMD500 (pressure)
Bosch Sensortec
AN18002
How to perform a SMB365 Selftest:
•
•
•
•
Put the BlueBox in a stable neutral-horizontal position
Select Operation Mode (example refers to Normal-Power Mode) [20]
Select acceleration range (example refers to low g Mode) [21]
Scale ordinate [27], [29] and abscissa [30] (example refers to ±512 LSB full scale, in 2g
range)
•
•
•
•
•
•
•
Start data acquisition [8]
Wait a few seconds
Activate Selftest (Selftest On) [24]
Wait a few seconds
Deactivate Selftest (Selftest Off) [24]
Stop data acquisition [9]
Interpret selftest by comparing LSB signals
A successful test shows a rising edge (signal ad on) while activating the Selftest function and a
falling edge (signal subtraction) while activating the Selftest function at every axis on the
acceleration signal output screen. Dependent on sensor, acceleration range and axis, the test
signal should respond a LSB value within the specified tolerance level in a stable neutral-
horizontal position of the board.
Acceleration range
Axis
X and Y
Z
Successful selftest signal
see related sensor datasheet
see related sensor datasheet
see related sensor datasheet
see related sensor datasheet
Low g (± 2g)
X and Y
Z
High g (± 10g)
Page 41
Rev. 1.0
© Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such
copying and passing onto third parties.
7211RB11.
Download from Www.Somanuals.com. All Manuals Search And Download.
Application Note
BlueBox Demo-Board for the digital sensors
SMB365 (acceleration) and SMD500 (pressure)
Bosch Sensortec
AN18002
4.4 Sensor Evaluation and Direct Data Export
Using the BST Sensor Desktop software in combination with the BlueBox demo board, it is
possible to perform a minor sensor evaluation. This includes both the SMD500 pressure and the
SMB365 acceleration sensor simultaneously. For basic evaluation purposes, the software
features a so-called online Direct Data Export in *.txt format via USB or wireless via Bluetooth.
The Direct Data Export is unlimited in time. While exporting the Data, for each tab activated
(Cockpit, Altimeter or Accelerometer) a corresponding header is automatically added to the *.txt
file. This means that only the active tab corresponding data is recorded.
Note: To sample either pressure or acceleration specific signals please use corresponding tab
for increased sampling speed.
How to perform a Direct Data Export:
•
Open menu “Export Data” from the Sensor Desktop menu bar.
•
Check “Activated” box
•
•
Browse and/or create storage folder
Choose appropriate filename and confirm with “OK”
Page 42
Rev. 1.0
© Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such
copying and passing onto third parties.
7211RB11.
Download from Www.Somanuals.com. All Manuals Search And Download.
Application Note
BlueBox Demo-Board for the digital sensors
SMB365 (acceleration) and SMD500 (pressure)
Bosch Sensortec
AN18002
•
If the Direct Data Export is activated correctly, the status message “Data export on”
appears at the bottom of the Sesor Desktop software window.
Status message
•
If the data acquisition is started by a click on “Start”, only the tab-corresponding data will
be exported. Regarding the figure above, only acceleration data will be exported.
Page 43
Rev. 1.0
© Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such
copying and passing onto third parties.
7211RB11.
Download from Www.Somanuals.com. All Manuals Search And Download.
Application Note
BlueBox Demo-Board for the digital sensors
SMB365 (acceleration) and SMD500 (pressure)
Bosch Sensortec
AN18002
•
Every time, the tabs (Cockpit, Altimeter and Accelerometer) are switched, the
corresponding data export to the *.txt file stops.
•
•
If started again, a corresponding new header is added to the *.txt file
The new sampled data will be automatically appended to the *.txt file
Page 44
Rev. 1.0
© Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such
copying and passing onto third parties.
7211RB11.
Download from Www.Somanuals.com. All Manuals Search And Download.
Application Note
BlueBox Demo-Board for the digital sensors
SMB365 (acceleration) and SMD500 (pressure)
Bosch Sensortec
AN18002
Document History and Modification
Rev. No Chapter
Description of Modification/Changes
Basic Description
Review
Name
Kult
kult
Date
10-July-06
18-July-06
0.0
1.0
All
All
Page 45
Rev. 1.0
© Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such
copying and passing onto third parties.
7211RB11.
Download from Www.Somanuals.com. All Manuals Search And Download.
Application Note
BlueBox Demo-Board for the digital sensors
SMB365 (acceleration) and SMD500 (pressure)
Bosch Sensortec
AN18002
1st Issue: No. 1.0
Date:
18-July-06
Signature:
signed Kult, BST/ENG
Revision No.:
No.:
No.:
No.:
No.:
Date:
Date:
Date:
Date:
Signature:
Signature:
Signature:
Signature:
Department:
BST/ENG
Date:
Signature:
18-July-06
signed Schatz, BST/ENG
Page 46
Rev. 1.0
© Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such
copying and passing onto third parties.
7211RB11.
Download from Www.Somanuals.com. All Manuals Search And Download.
|