Safe Operation Practices • Set-Up • Operation • Maintenance • Service • Troubleshooting • Warranty
OperatOr’s Manual
Two Stage Snow Thrower — Models 930 SWE & 933 SWE
WARNING
READ AND FOLLOW ALL SAFETY RULES AND INSTRUCTIONS IN THIS MANUAL
BEFORE ATTEMPTING TO OPERATE THIS MACHINE.
FAILURE TO COMPLY WITH THESE INSTRUCTIONS MAY RESULT IN PERSONAL INJURY.
CUB CADET LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019
Printed In USA
FORM NO. 769-02572A
(July, 2007)
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Safe Operation Practices
2
WARNING! This symbol points out important safety instructions which, if not followed,
could endanger the personal safety and/or property of yourself and others. Read and follow
all instructions in this manual before attempting to operate this machine. Failure to comply
with these instructions may result in personal injury.
When you see this symbol. HEED ITS WARNING!
CALIFORNIA PROPOSITION 65
WARNING! Engine Exhaust, some of its constituents, and certain vehicle components
contain or emit chemicals known to State of California to cause cancer and birth defects
or other reproductive harm.
DANGER: This machine was built to be operated according to the safe operation practices in
this manual. As with any type of power equipment, carelessness or error on the part of the
operator can result in serious injury. This machine is capable of amputating fingers, hands,
toes and feet and throwing foreign objects. Failure to observe the following safety
instructions could result in serious injury or death.
Training
Preparation
1.
Read, understand, and follow all instructions on the
Thoroughly inspect the area where the equipment is to be used.
Remove all doormats, newspapers, sleds, boards, wires and other
foreign objects, which could be tripped over or thrown by the
auger/impeller.
machine and in the manual(s) before attempting to
assemble and operate. Keep this manual in a safe place for
future and regular reference and for ordering replacement
parts.
1.
Always wear safety glasses or eye shields during operation
and while performing an adjustment or repair to protect
your eyes. Thrown objects which ricochet can cause serious
injury to the eyes.
2.
3.
Be familiar with all controls and their proper operation.
Know how to stop the machine and disengage them
quickly.
Never allow children under 14 years of age to operate this
machine. Children 14 and over should read and understand
the instructions and safe operation practices in this manual
and on the machine and be trained and supervised by an
adult.
2.
Do not operate without wearing adequate winter outer
garments. Do not wear jewelry, long scarves or other loose
clothing, which could become entangled in moving parts.
Wear footwear which will improve footing on slippery
surfaces.
4.
5.
Never allow adults to operate this machine without proper
instruction.
3.
4.
Use a grounded three-wire extension cord and receptacle
for all machines with electric start engines.
Thrown objects can cause serious personal injury. Plan
your snow-throwing pattern to avoid discharge of material
toward roads, bystanders and the like.
Adjust collector housing height to clear gravel or crushed
rock surfaces.
5.
6.
Disengage all control levers before starting the engine.
6.
7.
Keep bystanders, helpers, pets and children at least 75 feet
from the machine while it is in operation. Stop machine if
anyone enters the area.
Never attempt to make any adjustments while engine is
running, except where specifically recommended in the
operator’s manual.
Exercise caution to avoid slipping or falling, especially
when operating in reverse.
7.
Let engine and machine adjust to outdoor temperature
before starting to clear snow.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
5.
Never run an engine indoors or in a poorly ventilated area.
Engine exhaust contains carbon monoxide, an odorless
and deadly gas.
Safe Handling of Gasoline
To avoid personal injury or property damage use extreme care
in handling gasoline. Gasoline is extremely flammable and the
vapors are explosive. Serious personal injury can occur when
gasoline is spilled on yourself or your clothes which can ignite.
Wash your skin and change clothes immediately.
6.
7.
8.
9.
Do not operate machine while under the influence of
alcohol or drugs.
Muffler and engine become hot and can cause a burn. Do
not touch. Keep children away.
a. Use only an approved gasoline container.
Exercise extreme caution when operating on or crossing
gravel surfaces. Stay alert for hidden hazards or traffic.
b. Extinguish all cigarettes, cigars, pipes and other
sources of ignition.
Exercise caution when changing direction and while
operating on slopes.
c. Never fuel machine indoors.
d. Never remove gas cap or add fuel while the engine is
hot or running.
10. Plan your snow-throwing pattern to avoid discharge
towards windows, walls, cars etc. Thus, avoiding possible
property damage or personal injury caused by a ricochet.
e. Allow engine to cool at least two minutes before
refueling.
11. Never direct discharge at children, bystanders and pets or
allow anyone in front of the machine.
f.
Never over fill fuel tank. Fill tank to no more than ½
inch below bottom of filler neck to provide space for
fuel expansion.
12. Do not overload machine capacity by attempting to clear
snow at too fast of a rate.
g. Replace gasoline cap and tighten securely.
13. Never operate this machine without good visibility or light.
Always be sure of your footing and keep a firm hold on the
handles. Walk, never run.
h. If gasoline is spilled, wipe it off the engine and
equipment. Move machine to another area. Wait 5
minutes before starting the engine.
14. Disengage power to the auger/impeller when transporting
or not in use.
i.
Never store the machine or fuel container inside
where there is an open flame, spark or pilot light
(e.g. furnace, water heater, space heater, clothes
dryer etc.).
15. Never operate machine at high transport speeds on
slippery surfaces. Look down and behind and use care
when backing up.
j.
Allow machine to cool at least 5 minutes before
storing.
16. If the machine should start to vibrate abnormally, stop
the engine, disconnect the spark plug wire and ground it
against the engine. Inspect thoroughly for damage. Repair
any damage before starting and operating.
k. Never fill containers inside a vehicle or on a truck
or trailer bed with a plastic liner. Always place
containers on the ground away from your vehicle
before filling.
17. Disengage all control levers and stop engine before you
leave the operating position (behind the handles). Wait
until the auger/impeller comes to a complete stop before
unclogging the chute assembly, making any adjustments,
or inspections.
l.
If possible, remove gas-powered equipment from
the truck or trailer and refuel it on the ground. If this
is not possible, then refuel such equipment on a
trailer with a portable container, rather than from a
gasoline dispenser nozzle.
18. Never put your hand in the discharge or collector
openings. Always use the clean-out tool provided to
unclog the discharge opening. Do not unclog chute
assembly while engine is running. Shut off engine and
remain behind handles until all moving parts have stopped
before unclogging.
m. Keep the nozzle in contact with the rim of the fuel
tank or container opening at all times until fueling is
complete. Do not use a nozzle lock-open device.
Operation
19. Use only attachments and accessories approved by the
manufacturer (e.g. wheel weights, tire chains, cabs etc.).
1.
2.
3.
4.
Do not put hands or feet near rotating parts, in the auger/
impeller housing or chute assembly. Contact with the
rotating parts can amputate hands and feet.
20. When starting engine, pull cord slowly until resistance
is felt, then pull rapidly. Rapid retraction of starter cord
(kickback) will pull hand and arm toward engine faster than
you can let go. Broken bones, fractures, bruises or sprains
could result.
The auger/impeller control lever is a safety device. Never
bypass its operation. Doing so makes the machine unsafe
and may cause personal injury.
The control levers must operate easily in both directions
and automatically return to the disengaged position when
released.
21. If situations occur which are not covered in this manual, use
care and good judgment. Contact Customer Support for
assistance and the name of your nearest servicing dealer.
Never operate with a missing or damaged chute assembly.
Keep all safety devices in place and working.
4
sectiOn 2 — iMpOrtant safe OperatiOn practices
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance & Storage
Do not modify engine
1.
Never tamper with safety devices. Check their proper
operation regularly. Refer to the maintenance and
adjustment sections of this manual.
To avoid serious injury or death, do not modify engine in any
way. Tampering with the governor setting can lead to a runaway
engine and cause it to operate at unsafe speeds. Never tamper
with factory setting of engine governor.
2.
Before cleaning, repairing, or inspecting machine
disengage all control levers and stop the engine. Wait until
the auger/impeller come to a complete stop. Disconnect
the spark plug wire and ground against the engine to
prevent unintended starting.
Notice Regarding Emissions
Engines which are certified to comply with California and federal
EPA emission regulations for SORE (Small Off Road Equipment)
are certified to operate on regular unleaded gasoline, and
may include the following emission control systems: Engine
Modification (EM) and Three Way Catalyst (TWC) if so equipped.
3.
4.
5.
Check bolts and screws for proper tightness at frequent
intervals to keep the machine in safe working condition.
Also, visually inspect machine for any damage.
Do not change the engine governor setting or over-speed
the engine. The governor controls the maximum safe
operating speed of the engine.
Spark Arrestor
WARNING! This machine is equipped with an
internal combustion engine and should not be used
on or near any unimproved forest-covered, brush
covered or grass-covered land unless the engine’s
exhaust system is equipped with a spark arrester
meeting applicable local or state laws (if any).
Snow thrower shave plates and skid shoes are subject to
wear and damage. For your safety protection, frequently
check all components and replace with original equipment
manufacturer’s (OEM) parts only. “Use of parts which do
not meet the original equipment specifications may lead to
improper performance and compromise safety!”
If a spark arrester is used, it should be maintained in
effective working order by the operator. In the State of California
the above is required by law (Section 4442 of the California
Public Resources Code). Other states may have similar laws.
Federal laws apply on federal lands.
A spark arrester for the muffler is available through your
nearest engine authorized service dealer or contact the service
department, P.O. Box 361131 Cleveland, Ohio 44136-0019.
6.
Check control levers periodically to verify they engage
and disengage properly and adjust, if necessary. Refer
to the adjustment section in this operator’s manual for
instructions.
7.
8.
9.
Maintain or replace safety and instruction labels, as
necessary.
Observe proper disposal laws and regulations for gas, oil,
etc. to protect the environment.
Average Useful Life
According to the Consumer Products Safety Commission
(CPSC) and the U.S. Environmental Protection Agency (EPA),
this product has an Average Useful Life of seven (7) years, or 60
hours of operation. At the end of the Average Useful Life, buy
a new machine or have the machine inspected annually by an
authorized service dealer to ensure that all mechanical and
safety systems are working properly and not worn excessively.
Failure to do so can result in accidents, injuries or death.
Prior to storing, run machine a few minutes to clear snow
from machine and prevent freeze up of auger/impeller.
10. Never store the machine or fuel container inside where
there is an open flame, spark or pilot light such as a water
heater, furnace, clothes dryer etc.
11. Always refer to the operator’s manual for proper
instructions on off-season storage.
12. Check fuel line, tank, cap, and fittings frequently for cracks
or leaks. Replace if necessary.
13. Do not crank engine with spark plug removed.
WARNING! Your Responsibility—Restrict the use of this power machine to persons who read, understand and
follow the warnings and instructions in this manual and on the machine.
SAVE THESE INSTRUCTIONS!
sectiOn 2 — iMpOrtant safe OperatiOn practices
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly & Set-Up
3
Contents of Carton
•
•
One Snow Thrower
•
•
Two Replacement Auger Shear Pins
•
•
One Chute Assembly
One Snow Thrower Operator’s
Manual
One Tecumseh Engine Operator’s
Manual
One Product Registration Card
4. Secure the upper handle and lower handle with the two
wing nuts, belleville washers, and carriage bolts removed
earlier. Tighten the two wing nuts already installed in the
upper holes to firmly secure the upper handle and sup-
port tubes. See Figure 3-2.
Assembly
IMPORTANT: Two replacement auger shear pins are
included with this manual (or stowed in the plastic handle
panel). Refer to the Maintenance section for more informa-
tion regarding shear pin replacement.
NOTE: All references in this manual to the left or right side
of the snow thrower is from the operating position only.
Exceptions, if any, will be specified.
IMPORTANT: This unit is shipped with the engine full of
oil. After assembly, refer to the Tecumseh Engine manual
packed separately with your snow thrower for fuel and oil
fill-up details.
NOTE: Specifications are subject to change without
notification or obligation. Images may not reflect your
exact model and are for reference purposes only.
Handle
1. Remove any packaging material from the upper handle.
2. Remove the lower plastic wing nut, belleville washer
and carriage bolt from each side of the upper handle;
then raise the upper handle assembly until it snaps over
the lower handle. See Figure 3-1.
Figure 3-ꢀ
Chute Directional Control
1. Remove the flat washer and hairpin clip from the end of
the chute directional control. See Fig. 3-3.
B
A
Figure 3-3
2. Insert the end of the chute directional control into the
lower bracket and secure with the flat washer and hairpin
clip just removed. If necessary, the lower bracket can be
adjusted. Refer to Chute Bracket Adjustment on Page 16.
Figure 3-1
3. Looking beneath the handle panel, check that all of the
cables (steering, auger, shift, and drive) are properly
routed and not pinched or kinked. Make certain the
springs at the lower end of the auger and drive cables are
securely hooked into their respective actuator bracket.
Chute Assembly
1. Remove lock nuts and screws securing one of the flange
keepers to the chute assembly. Loosen the fasteners of
the other two flange keepers. See Figure 3-4.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Place chute assembly onto chute base as shown in Figure
3-4. Make sure that the chute notches engage with the
spiral end of chute directional control, and the two flange
keepers are beneath the flange on the chute base.
Headlight Harness
If not already done, wrap the wires of the headlight wire
harness around the lower right handle; then attach the
wires to the engine as shown in Figure 3-7.
B
A
Figure 3-7
Figure 3-4
Set-Up
3. Secure flange keeper removed earlier with lock nuts
and screws. Tighten down nuts securing the other two
flange keepers. See Figure 3-5.
Shear Pins
A pair of replacement auger shear pins and bow tie cotter pins
have been included with your snow thrower. There are holes
provided in the plastic dash panel for convenient storage of the
shear pins. Push the pins through the holes in the dash panel
and secure with the bow-tie cotter pins. See Fig. 3-8.
Figure 3-5
4. Check that the chute cables are properly routed
through the cable guide on top of engine shroud. See
Figure 3-6.
Figure 3-8
Chute Clean-Out Tool
The chute clean-out tool is fastened to the top of the auger
housing with a mounting clip and a cable tie at the factory. Cut
the cable tie before operating the snow thrower. See Fig. 3-9.
Cable
Chute
Cables
Guide
Cleanout Tool
Figure 3-6
Figure 3-9
sectiOn 3 — asseMbly & set-up
7
Download from Www.Somanuals.com. All Manuals Search And Download.
2. While observing the distance between the shave plate
and the ground, adjust the skids shoes up or down to
achieve the desired shave plate height. See Figure 3-10.
Tire Pressure (Pneumatic Tires)
The tires are over-inflated for shipping purposes. Check the
tire pressure before operating the snow thrower. Refer to
the tire side wall for tire manufacturer’s recommended psi
and deflate (or inflate) the tires as necessary.
3. Make certain the entire bottom surface of skid shoes are
against the ground to avoid uneven wear on the skid
shoes; then tighten nuts and bolts securely.
NOTE: If the tire pressure is not equal in both tires, the unit
may pull to one side or the other and the shave plate will
not sit level on the ground.
Auger and Drive Control Cables
WARNING! Prior to operating your snow
thrower, carefully read and follow all instructions
below. Perform all adjustments to verify your
snow thrower is operating safely and properly.
IMPORTANT: Under any circumstance do not exceed
manufacturer’s recommended psi. Equal tire pressure
should be maintained at all times. Excessive pressure when
seating beads may cause tire/rim assembly to burst with
force sufficient to cause serious injury. Refer to sidewall of
tire for recommended pressure.
Testing Auger Drive Control
1. When the auger control is released and in the disen-
gaged “up” position, the cable should have very little
slack. It should NOT be tight. Refer to Figure 3-11.
Adjustments
Skid Shoes
The snow thrower skid shoes are adjusted upward at the
factory for shipping purposes. Adjust them downward, if
desired, prior to operating the snow thrower.
Shift Lever
Chute Tilt Control
CAUTION: It is not recommended that you
operate this snow thrower on gravel as it can
easily pick up and throw loose gravel, causing
personal injury or damage to the snow thrower
and surrounding property.
Auger
Drive
Control
Control
•
•
For close snow removal on a smooth surface, adjust the
skid shoes so that the shave plate on the bottom of the
auger housing is just off the ground.
Adjust the skid shoes to a lower position to raise the
shave plate off the ground when clearing uneven areas,
such as a ribbon type driveway or a gravel driveway
Drive
Auger
Control
Cable
Control
Cable
NOTE: If you choose to operate the snow thrower on a gravel
surface, keep the skid shoes in position for maximum clearance
between the ground and the shave plate.
To adjust the skid shoes:
1. Adjust skid shoes by loosening the six (three on each
side) hex nuts, washers, and carriage bolts securing the
skid shoes to the auger housing. Refer to Figure 3-10.
Figure 3-11
2. In a well-ventilated area, start the snow thrower engine
as instructed in Section 5 - “Operation” on page 13.
Make sure the throttle is set in the FAST position.
Lower
Shave
Plate
3. While standing in the operator’s position (behind the
snow thrower), engage the auger.
Shave
Plate
Raise
Shave
Plate
Figure 3-10
8
sectiOn 3— asseMbly & set-up
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Allow the auger to remain engaged for approximately
ten (10) seconds before releasing the auger control.
Repeat this several times.
5. With the throttle control in the FAST (rabbit) position
and the auger control in the disengaged “up” position,
walk to the front of the machine.
6. Confirm that the auger has completely stopped rotating
and shows NO signs of motion. If the auger shows ANY
signs of rotating, immediately return to the operator’s
position and shut off the engine. Wait for ALL moving
parts to stop before re-adjusting the auger control.
Testing Drive Control & Shift Lever
1. With the engine turned off, move the shift lever into
sixth (6) position. Refer to Figure 3-11.
2. With the wheel drive control released, push the snow
thrower forward, then pull it back. The machine should
move freely.
Figure 3-1ꢀ
3. Engage the drive control and attempt to move the ma-
chine both forward and back, resistance should be felt.
4. Move the shift lever into the fast reverse (R2) position
and repeat the previous two steps.
5. If you experienced resistance rolling the unit, either
when repositioning the shift lever from 6 to R2 or when
attempting to move the machine with the drive control
released, adjust the drive control immediately. See
Adjusting Drive and Auger Controls.
Adjusting Drive and Auger Controls
1. From beneath the handle, pull downward on the appro-
priate cable and unhook the spring found on the end of
the cable from its respective actuator bracket. Refer to
Figures 3-11 and 3-12.
2. Slide the spring up the cable to expose the cable cou-
pler threads and lock nut. Refer to Figure 3-13.
3. Adjust the lock nut as follows: If adjusting the drive
cable, thread the lock nut outward (down the coupler)
to lengthen the cable and allow the unit to move freely
when the control is released. Thread the lock nut inward
(up the coupler) to shorten the cable to reduce slippage
and prevent the machine from being easily moved with
the drive control engaged.
Figure 3-13
Gas & Oil Fill-Up
WARNING! Use extreme care when handling
gasoline. Gasoline is extremely flammable
and the vapors are explosive. Never fuel the
machine indoors or while the engine is hot or
running. Extinguish cigarettes, cigars, pipes and
other sources of ignition.
Service the engine with gasoline and oil as instructed in
the Tecumseh Engine Operator’s Manual packed separately
with your snow thrower. Read instructions carefully.
WARNING! Do not over-tighten the cable.
Over-tightening may prevent the auger from
disengaging and compromise the safety of the
snow thrower.
4. If adjusting the auger cable, thread the lock nut down to
lengthen the cable as necessary to stop the auger from
turning when the control is released.
5. Securely hook each cable’s spring into the appropriate
hole of the respective actuator bracket. The auger cable
hooks into the forward-most hole in the bracket, the
drive cable hooks into the rear-most hole of its bracket.
6. Repeat the wheel drive and auger control tests to verify
proper adjustment. Repeat previous steps if necessary
to attain proper adjustment of each cable
sectiOn 3 — asseMbly & set-up
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Controls and Features
4
Drive Control
Shift Lever
Two-Way
Chute Control™
Auger Control
Headlight
Fuel Tank
Gas Cap
Wheel Steering
Control
Oil Fill
Chute
Assembly
Chute Directional
Control
Engine Controls
Recoil Starter
Handle
Electric Starter
Switch
Primer
Bulb
Ignition
Key
Choke
Control
Throttle
Control
Clean-Out
Tool
Augers
Skid Shoe
Figure 4-1
Snow thrower controls and features are described below
and illustrated in Fig. 4-1.
Choke Control
NOTE: For detailed information on all engine controls,
refer to the separate Tecumseh Engine Operator’s Manual.
Shift Lever
The shift lever is located in the right side of
the handle panel and is used to determine
ground speed and direction of travel.
The choke control is found on the rear of the engine and
is activated by rotating the knob clockwise. Activating the
choke control closes the choke plate on the carburetor and
aids in starting the engine.
Forward
Ignition Key
There are six forward (F) speeds. Position one
(1) is the slowest and position six (6) is the
fastest.
The ignition key is a safety devise. It must be fully inserted
in order for the engine to start. Remove the ignition key
when the snow thrower is not in use.
Reverse
Important: Do not turn the ignition key in an attempt to
start the engine. Doing so may cause it to break.
There are two reverse (R) speeds. One (R1) is
the slower and two (R2) is the faster.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Throttle Control
Auger Control
The throttle control is located on the rear
of the engine. It regulates the speed of the
engine and will shut off the engine when
moved into the STOP position.
Primer Bulb
Pressing the primer bulb forces fuel directly
into the engine’s carburetor to aid in starting
a “Cold” engine. NOTE: Do not use the
primer bulb to restart a warm engine after a
short shutdown.
Oil Fill
Engine oil level can be checked and oil
added through the oil fill.
The auger control is located on the left handle. Squeeze
the control grip against the handle to engage the augers
and start snow throwing action. Release to stop.
Skid Shoes
Position the skid shoes based on surface conditions. Adjust
upward for hard-packed snow. Adjust downward when
operating on gravel or crushed rock surfaces.
Drive Control / Auger Clutch Lock
Electric Starter Outlet
Requires the use of a three-prong outdoor extension cord
and a 120V power source/wall outlet.
Recoil Starter Handle
This handle is used to manually start the engine.
Electric Starter Switch
Pressing the button on the top of the electric starter switch
engages the engine’s electric starter when plugged into a
120V power source.
Augers
When engaged, the augers rotate and draw snow into the
auger housing.
The drive control is located on the right handle. Squeeze
the control grip against the handle to engage the wheel
drive. Release the handle to stop.
Chute Assembly
Snow drawn into the auger housing is discharged out the
chute assembly.
The drive control also locks the auger control so that
you can operate the chute directional control without
interrupting the snow throwing process. If the auger
control is engaged simultaneously with the drive control,
the operator can release the auger control (on the left
handle) and the augers will remain engaged. Release both
controls to stop the augers and wheel drive.
Gas Cap
Unthread the gas cap to add gasoline to the fuel tank.
Note: Always release the drive control before changing
speeds. Failure to do so will result in increased wear on
your machine’s drive system.
sectiOn 4 — cOntrOls and features
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Two-Way Chute Control™
Wheel Steering Controls
The two-way chute control is located on the left side of
the dash panel and is used to control the distance of snow
discharge from the chute.
The left and right wheel steering controls are located on
the underside of the handles. Squeeze the right control to
turn right; squeeze the left control to turn left.
•
To change the upper chute angle to control the
distance that snow is thrown, pivot the lever forward
or backward.
NOTE: Operate the snow thrower in open areas until you are
familiar with these controls.
Chute Clean-Out Tool
CHUTE DIRECTIONAL CONTROL
WARNING! Never use your hands to clear a
clogged chute assembly. Shut off engine and
remain behind handles until all moving parts
have stopped before unclogging.
DISCHARGE
RIGHT
DISCHARGE
LEFT
The chute clean-out tool is conveniently fastened to the
rear of the auger housing with a mounting clip. Should
snow and ice become lodged in the chute assembly during
operation, proceed as follows to safely clean the chute
assembly and chute opening:
CHUTE TILT
DOWN
1. Release both the Auger Control and the Drive
Control.
CHUTE TILT
UP
2. Stop the engine by removing the ignition key.
3. Remove the clean-out tool from the clip which
secures it to the rear of the auger housing.
•
•
Move the lever forward to pivot the upper chute down
and reduce the distance snow is thrown.
4. Use the shovel-shaped end of the clean-out tool
to dislodge and scoop any snow and ice which has
formed in and near the chute assembly.
Move the lever rearward to pivot the upper chute
upward and increase the distance snow is thrown.
Chute Directional Control
The chute directional control is located on the left side of
the snow thrower.
5. Refasten the clean-out tool to the mounting clip on
the rear of the auger housing, reinsert the ignition
key and start the snow thrower’s engine.
6. While standing in the operator’s position (behind the
snow thrower), engage the auger control for a few
seconds to clear any remaining snow and ice from the
chute assembly.
•
To change the direction in which snow is thrown,
crank clockwise to discharge to the left and
counterclockwise to discharge to the right.
1ꢀ
sectiOn 4— cOntrOls and features
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
5
5. As the engine warms, slowly rotate the choke control
to the OFF position. If the engine falters, quickly
rotate the choke control back toward FULL choke, and
then slowly into the OFF position again.
Starting The Engine
1. Attach spark plug wire to spark plug. Make certain
the metal loop on the end of the spark plug wire
(inside the rubber boot) is fastened securely over the
metal tip on the spark plug.
6. When disconnecting the extension cord, always
unplug the end at the three-prong wall outlet before
unplugging the opposite end from the snow thrower.
2. Make certain both the auger control and drive control
are in the disengaged (released) position.
Recoil Starter
3. Move throttle control up to FAST position. Insert
ignition key into slot. Make sure it snaps into place.
Do not attempt to turn the key.
1. Rotate choke control to FULL choke position (cold
engine start).
NOTE: If the engine is already warm, place choke
control in the OFF position instead of FULL.
NOTE: The engine cannot start unless the key is
inserted into ignition switch.
2. Push the primer two or three times for cold engine
start, making sure to cover vent hole in the center of
the primer when pushing.
Electric Starter
Determine that your home’s wiring is a three-wire
grounded system. Ask a licensed electrician if you are not
certain.
NOTE: DO NOT use primer to restart a warm engine
after a short shutdown.
WARNING! The optional electric starter is
equipped with a grounded three-wire power
cord and plug, and is designed to operate on
120 volt AC household current. It must be used
with a properly grounded three-prong
receptacle at all times to avoid the possibility of
electric shock. Follow all instructions carefully
prior to operating the electric starter.
NOTE: Additional priming may be necessary if the
temperature is below 15° Fahrenheit.
3. Grasp the recoil starter handle and slowly pull the
rope out. At the point where it becomes slightly
harder to pull the rope, stop pulling and allow the
rope to slowly recoil.
4. Pull the starter handle with a firm, rapid stroke. Do
not release the handle and allow it to snap back.
Keep a firm hold on the starter handle and allow it to
slowly recoil.
If you have a grounded three-prong receptacle, proceed as
follows:
1. Plug the extension cord into the outlet located on the
engine’s surface. Plug the other end of extension cord
into a three-prong 120-volt, grounded, AC outlet in a
well-ventilated area.
5. As the engine warms, slowly rotate the choke control
to the OFF position. If the engine falters, quickly
rotate the choke control back toward the FULL choke
position, and then slowly into the OFF position again.
2. Rotate choke control to FULL choke position (for a
cold engine start).
NOTE: Allow the engine to warm up for a few minutes
after starting. The engine will not develop full power
until it reaches operating temperatures.
NOTE: If the engine is already warm, place choke
control in the OFF position instead of FULL.
Stopping The Engine
Run engine for a few minutes before stopping to help dry
off any moisture on the engine.
3. Push the primer two or three times for cold engine
start, making sure to cover vent hole in the center of
the primer when pushing.
NOTE: DO NOT use primer to restart a warm engine
after a short shutdown.
1. Move throttle control to STOP position.
2. Remove the ignition key and store in a safe place.
4. Push starter button to start engine. Once the engine
starts, release starter button.
3. Wipe all snow and moisture from the area around
the engine as well as the area in and around the drive
control and auger control. Also, engage and release
both controls several times.
NOTE: Do NOT hold the button down for longer than
seven (7) seconds at a time. Doing so may damage
your engine’s electric starter.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
To Engage Drive
Operating Tips
NOTE: Allow the engine to warm up for a few minutes.
The engine will not develop full power until it reaches
operating temperature.
1. With the throttle control in the Fast (rabbit) position,
move shift lever into one of the six forward (F)
positions or two reverse (R) positions. Select a speed
appropriate for the snow conditions and a pace
you’re comfortable with.
WARNING: The temperature of the muffler
and the surrounding areas may exceed 150° F.
Avoid these areas.
NOTE: Use slower speeds in higher snow and/or until you
are familiar with the snow thrower operation
1. If possible, remove snow immediately after it falls.
2. Discharge snow downwind whenever possible.
3. Slightly overlap each previous path.
2. Squeeze the drive control against the handle the
snow thrower will move. Release it and drive motion
will stop.
4. Set the skid shoes 1/4” below the shave plate for
normal usage. Adjust them upward for hard-packed
snow and downward when using on gravel or
crushed rock.
CAUTION: NEVER move the shift lever without
first releasing the wheel drive control. Doing so
will cause premature wear on the drive system’s
friction wheel
3. To turn the snow thrower to the left or right, squeeze
the respective wheel steering control. Refer to Figure
4-1.
Replacing Shear Pins
Each of the four auger spiral assemblies are secured to the
spiral shaft with a shear pin and cotter pin. If the auger
should strike a foreign object or ice jam, the snow thrower
is designed so that the pins may shear. If the augers will
not turn, check to see if the pins have sheared. See Fig. 5-1.
To Engage Augers
1. To engage the augers and start throwing snow,
squeeze the auger control against the left handle.
Release to stop the augers.
CAUTION: NEVER replace the auger shear pins
with anything other than OEM Part No. 738-
04155 replacement shear pins. Any damage to
the auger gearbox or other components as a
result of failing to do so will NOT be covered by
your snow thrower’s warranty.
2. While the auger control is engaged, squeeze the drive
control to engage the interlock mechanism and to
drive the snow thrower. The interlock mechanism
locks the auger control so you can turn the chute
control without interrupting the snow throwing
process.
WARNING! Always turn off the snow thrower’s
engine and remove the key prior to replacing
shear pins.
3. Release the auger control; the interlock mechanism
should keep the auger control engaged until the
drive control is released.
4. Release the drive control to stop both the augers and
the wheel drive. To stop the auger, both levers must
be released.
Shear Pin
Cotter Pin
Figure 5-1
14
sectiOn 5— OperatiOn
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance & Adjustments
6
3. Slide the shave plate out of the off-set slot at the
Maintenance
Engine
Refer to the Tecumseh Engine manual packed with your
machine for all engine maintenance.
bottom of the housing, and from between the skid
shoes and side panels of the housing.
4. With the mounting holes toward the back, slide the
new shave plate into position and secure with the
fasteners removed previously.
Shave Plate and Skid Shoes
The shave plate and skid shoes on the bottom of the snow
thrower are subject to wear. They should be checked
periodically and replaced when necessary.
Lubrication
Gear Shaft
The gear (hex) shaft should be lubricated at least once a
season or after every twenty-five (25) hours of operation.
NOTE: The skid shoes on this machine have two wear edges.
When one side wears out, they can be rotated 180° to use the
other edge.
1. Carefully pivot the snow thrower up and forward so
that it rests on the auger housing.
To Remove skid shoes:
2. Remove the frame cover from the underside of the
snow thrower by removing four self-tapping screws
which secure it. Refer to Figure 6-6.
3. Apply a light coating of engine oil (or 3-in-1 oil) to the
hex shaft. See Fig. 6-2.
1. Remove the six carriage bolts, hex nuts, and bell
washers that secure the two skid shoes to the sides of
the auger housing. Refer to Figure 6-1.
2. Position the new skid shoes and secure with the
carriage bolts, bell washers, and hex nuts. Make
certain the skid shoes are adjusted to be level. Refer
to Fig. 6-1.
Hex
Shaft
Skid Shoe
Shave
Plate
Figure 6-ꢀ
NOTE: When lubricating the hex shaft, be careful not to get
any oil on the aluminum drive plate or the rubber friction
wheel. Doing so will hinder the snow thrower’s drive system.
Wipe off any excess or spilled oil
Figure 6-1
To replace shave plate:
Wheels
1. Remove the hex nuts, bell washers, and carriage bolts
that secure the shave plate to the bottom of the snow
thrower housing.
At least once a season, remove both wheels. Clean and
coat the axles with a multipurpose automotive grease
before reinstalling wheels.
2. Remove the rear most hex nut, bell washer, and
carriage bolt securing the back of each skid shoe to
the sides of the housing. Loosen the remaining hex
nuts securing the skid shoes.
Chute Directional Control
Once a season, lubricate the eye-bolt bushing and the
spiral with 3-in-1 oil.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Auger Shaft
Adjustments
Shift Cable
If the full range of speeds (forward and reverse) cannot be
achieved, refer to the Figure 6-4 and adjust the shift cable
as follows:
At least once a season, one at a time, remove the shear
pins from the auger shaft. Spray lubricant inside the hub
of each auger spiral assembly and around the spacers on
the auger shaft. See Figure 6-3.
Grease fittings can also be found at each end of the auger
shaft. Lubricate with a grease gun once a season. See
Figure 6-3.
1. Place the shift lever in the fastest forward speed
position.
2. Loosen the hex nut on the shift cable index bracket.
See Fig. 6-4.
Grease
Fitting
Shear Pin
Vent Plug
Figure 6-4
3. Pivot the bracket downward to take up slack in the
cable.
Cotter Pin
Spacers
4. Retighten the hex nut.
Figure 6-3
Chute Bracket Adjustment
If the spiral at the bottom of the chute directional control
is not fully engaging with the chute assembly, the chute
bracket can be adjusted. To do so:
Gear Case
The auger gear case is equipped with a grease fitting.
Lubricate with Shell Alvania lead-free grease once a season
(order part number 737-0168). See Figure 6-3.
1. Loosen the two nuts which secure the chute bracket
and reposition it slightly. See Figure 6-5.
NOTE: To relieve pressure, remove the vent plug before
lubricating the gear case. See Figure 6-3. Failure to do so could
result in damage to the gear case seals.
Augers
Each of the four auger spiral assemblies is secured to the
spiral shaft with a shear pin and cotter pin. If the auger
should strike a foreign object or ice jam, the snow thrower
is designed so that the pins may shear.
1. If augers do not turn, check to see if pins have
sheared.
2. Replace the pins if needed. Two replacement shear
pins and cotter pins have been provided with the
snow thrower. Spray an oil lubricant into shaft before
inserting new pins and securing with new cotter pins.
Figure 6-5
2. Retighten the nuts.
16
sectiOn 6— Maintenance & adjustMents
Download from Www.Somanuals.com. All Manuals Search And Download.
3. With the drive control engaged, the friction wheel
must contact the drive plate. Refer to Figure 6-7.
Drive Control
Refer to “Auger and Drive Control Cables” of the Assembly & Set-
Up - Section 3 for instructions to adjust the drive control.
To further check the adjustment, proceed as follows:
4. If there is no friction wheel clearance, or the friction
wheel does not solidly contact the drive plate,
re-adjust the lock nut on the lower end of the drive
cable following the instructions in the Assembly
section.
1. With the snow thrower tipped forward (be certain
to drain gasoline or place plastic film under the gas
cap if the snow thrower has already been operated),
remove the frame cover underneath the snow
thrower by removing the self-tapping screws. See
Figure 6-6.
5. Reassemble the frame cover.
Chute Directional Control
The distance snow is thrown can be adjusted by adjusting
the angle of the chute assembly. Move the remote chute
lever on the control panel forward to pivot the upper
chute down; move the lever rearward to pivot the upper
chute upward.
The chute directional control is located on the left side of
the snow thrower. To change the direction in which snow
is thrown, crank clockwise to discharge to the left and
counterclockwise to discharge to the right.
Auger Control
Figure 6-6
Refer to the Assembly and Set-up section for instructions
on adjusting the auger control cable.
2. Locate the opening between the axle support
bracket and the front frame support (See Figure 6-7).
Looking through this opening, with the drive control
released, there must be clearance between the
friction wheel and the drive plate in all positions of
the shift lever.
Skid Shoes
Refer to the Assembly and Set-up section for instructions
on adjusting the skid shoes.
Tire Pressure
Refer to the tire sidewall for the manufacturer’s recom-
mended tire air pressure. Keep the tires filled to the
recommended psi.
If the tire pressure is not equal in both tires, the unit may
pull to one side or the other
Friction
Wheel
Drive
Plate
Axle Supp.
Brkt.
Opening
Figure 6-7
sectiOn 6 — Maintenance & adjustMents
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Service
7
Belt Replacement
Belt Removal Preparation
Remove
1. Disconnect the chute crank assembly at the discharge
chute end by removing the hairpin clip and the flat
washer. Refer to Figure 7-1.
Loosen
Figure 7-3
Auger Belt Replacement
To remove and replace your snow thrower’s auger belt,
proceed as follows:
1. Remove the hairpin clip and flat washer from the
ferrule in order to disconnect the auger idler rod from
the brake bracket assembly. See Figure 7-4.
NOTE: Make sure to maintain the location of the ferrule
on the idler rod.
Figure 7-1
2. Remove the plastic belt cover on the front of the
engine by removing the three self-tapping screws. See
Fig. 7-2.
Figure 7-4
Figure 7-ꢀ
2. Slip the auger control belt (the front belt) off the
engine pulley.
3. Loosen the bolt shown in Figure 7-3 securing the belt
keeper bracket and remove the other bolt. Push the
belt keeper bracket up off the engine pulley. Refer to
Figure 7-3.
3. Pull the brake bracket assembly towards the cable
guide roller and unhook the auger cable “Z” fitting.
Refer to Figure 7-5.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
ensure the adapter does fall and get damaged when
removing the pulley.
8. Place the new auger belt in the V-groove of the auger
pulley and place the pulley w/belt inside the belt
keepers.
Adapter Post
B
Figure 7-5
4. From both sides of the frame assembly, use a 1/2"
wrench to remove the three hex tap screws securing
the transmission frame to the auger housing assembly.
Refer to Figure 7-1. NOTE: Do not remove the lower hex
flange lock nut on each side.
C
Pulley Slot
Belt Keeper
A
5. Place a block of wood underneath the auger housing as
shown in Figure 7-6 and separate auger housing from
the transmission frame by tilting the housing forward
and pulling up the handles.
Figure 7-7
9. Turn the pulley as necessary to align its three slots
approximately with the posts of the pulley adapter, then
move the brake bracket assembly away from the input
shaft. While aligning the pulley slots and adapter
posts, push the auger pulley fully onto the adapter.
Refer to Figure 7-7.
NOTE: If the pulley adapter was removed with the pulley,
align the splines of the pulley adapter and auger input
shaft, and push the pulley and adapter onto the input
shaft. Refer to Figure 7-7.
10. Slide the washer onto the hex screw removed earlier
and apply Loctite 262 to the threads of the hex screw.
11. Insert the hex screw through the pulley assembly and
into the threads of the input shaft. Torque the hex
screw to 250-325 in. /lbs. to secure the auger pulley
assembly on the input shaft.
12. If also replacing the drive belt, proceed to the “Drive
Belt” instruction. If not, reposition the transmission
frame back onto the auger housing. Install the drive
belt on the engine pulley, re-connect the auger cable
“Z” fitting and auger idler rod ferrule to the brake
bracket. Reposition and secure the engine pulley belt
guard, and re-install the belt cover.
Figure 7-6
6. Block the impeller with a piece of wood the prevent
from spinning and use a 1/2” wrench to remove the
hex screw and flat washer from the center of the auger
input shaft and auger pulley adapter. Refer to Figure
7-7.
NOTE: Make sure to remove the piece of wood blocking
the impeller.
7. Lift the brake bracket assembly out of the pulley
groove and slide the pulley assembly off the posts of
the auger pulley adapter to remove the old belt. Refer
to Figure 7-7.
Check the auger drive belt adjustment. With the auger
clutch lever in the disengaged position, the top surface of
the new belt should be even with the outside diameter of
the pulley.
NOTE: The pulley adapter may slide off the auger input
shaft when removing the pulley. Use extra caution to
sectiOn 7 — service
19
Download from Www.Somanuals.com. All Manuals Search And Download.
To adjust, disconnect ferrule from brake bracket assembly.
Thread ferrule in (towards idler) to increase tension on belt,
or out to decrease belt tension.
3. Remove screws from the frame cover underneath the
snow thrower (refer to Figure 7-9). Remove the right
wheel from the axle.
NOTE: The brake puck must always be firmly seated in the
pulley groove when auger control is disengaged.
IMPORTANT: Repeat the “Testing Auger Drive Control” from
the Assembly and Set-up section before operating the
snow thrower.
Drive Belt Replacement
If not already done, remove the auger drive belt from the
front pulley of the engine double pulley. Refer to “Auger
Belt Replacement” instructions in the previous sub-section.
1. Pull the idler pulley away from the backside of the drive
belt to relieve the tension and slip the drive belt off the
idler pulley. Carefully release the idler pulley. See Figure
7-8.
Figure 7-9
4. Using a 3/4” wrench, hold the hex shaft and remove the
hex screw and belleville washer and bearing from left
side of the frame. Refer to Figure 7-10.
3
Friction Wheel Ass’y.
Remove Hex Screw
Belleville Washer
1b
1a
Slide Hex
Shaft Out
Right Side
2
Hex Shaft
Figure 7-8
Figure 7-10
5. Holding the friction wheel assembly, slide the hex shaft
out of the right side of the frame. The spacer on the left
side of the hex shaft will fall and the sprocket should
remain hanging lose in the chain.
2. Roll the drive belt off the lower drive pulley and then
remove the belt from the engine pulley.
3. Install the new belt on the pulleys in the reverse order and
re-tension with the idler pulley.
6. Lift the friction wheel assembly out between the axle
shaft and the drive shaft assemblies.
4. Reassemble by performing the previous steps in the
opposite order and manner of removal.
7. Remove four screws securing the friction wheel to the
hub assembly (refer to Figure 7-11). Discard old friction
wheel.
Changing Friction Wheel
The rubber on the friction wheel is subject to wear and
should be checked after the first 25 hours of operation,
and periodically thereafter. Replace the friction wheel if
any signs of wear or cracking are found.
8. Reassemble the new friction wheel onto the hub
assembly, tightening the four screws in rotation and
with equal force. It is important to assemble the friction
wheel symmetrically for proper functioning. Refer to
Figure 7-11.
1. Drain the gasoline from the snow thrower, or place a
piece of plastic under the gas cap.
2. Tip the snow thrower up and forward, so that it rests on
the housing.
ꢀ0
sectiOn 7— service
Download from Www.Somanuals.com. All Manuals Search And Download.
15. Place the belleville washer (rounded side toward head)
onto the hex screw removed earlier, and insert the
screw into the threaded hole of the hex shaft.
16. Gradually tighten the hex screw to fully seat the
bearings in each side of the frame and to secure the
hex shaft.
17. Position the frame cover on the bottom of the frame
and secure with the self-tapping screws. Pivot the snow
thrower down to its normal operating position.
NOTE: If you placed plastic film under the gas cap, be
certain to remove it.
Off-Season Storage
Figure 7-11
If the snow thrower will not be used for 30 days or longer,
the equipment needs to be stored properly. Follow storage
instructions below to ensure top performance from the
snow thrower for many more years.
9. Reposition the friction wheel assembly in the snow
thrower frame. Insert the pin from the shift arm
assembly into the friction wheel assembly and hold
assembly in position. Refer to Figure 7-12.
NOTE: Refer to the engine manual for more detailed
information on preparing the snow thrower engine for
storage.
Short-Term Storage
It is important to prevent gum deposits from forming
in essential fuel system parts of the engine such as the
carburetor, fuel filter, fuel hose, or tank during short-term
storage (15-30 days). To prevent this, treat the fuel system
using a fuel stabilizer.
Fuel stabilizer (such as STA-BIL™ or ULTRA-FRESH™) is an
acceptable alternative in minimizing the formation of fuel
gum deposits during storage. Add stabilizer to gasoline
in fuel tank or storage container. Always follow mix ratio
found on stabilizer container. Run engine at least 10
minutes after adding stabilizer to allow it to reach the
carburetor.
Figure 7-12
WARNING: Never store snow thrower with fuel
in tank indoors or in poorly ventilated areas,
where fuel fumes may reach an open flame,
spark or pilot light as on a furnace, water heater,
clothes dryer or gas appliance.
10. Slide the hex shaft through the right side of the frame
toward the left side and through the friction wheel
assembly.
NOTE: If the sprocket fell from the snow thrower chain
while removing the hex shaft, position the hex hub of the
sprocket toward the friction wheel and place the sprocket
in the chain.
Long-Term Storage
To avoid engine problems, the fuel system should be
emptied before storage for 30 days or longer.
1. Run the engine until the fuel tank is empty and it stops
due to lack of fuel. Do not attempt to pour fuel from
the engine.
11. After making certain that the chain is on both the large
and the small sprocket, align the hex shaft with the hex
hub of the small sprocket, and slide the shaft through
the sprocket.
2. Remove the spark plug and pour one (1) ounce of
engine oil through the spark plug hole into the
cylinder. Cover spark plug hole with a rag and crank the
engine several times to distribute the oil. Replace spark
plug.
12. Slide the spacer onto the end of the hex shaft.
13. Align the bearing on the right end of the hex shaft with
the hole in the right side of the frame, then push the
hex shaft to the left into position in the frame.
WARNING: Never use engine or carburetor
cleaning products in the fuel tank or
permanent damage may occur.
14. Slide the bearing onto the left end of the hex shaft and
press into the hole on the left side the frame.
sectiOn 7 — service
ꢀ1
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
8
Problem
Cause
Remedy
Engine fails to start
1. Choke control not in ON position.
2. Spark plug wire disconnected.
3. Fuel tank empty or stale fuel.
4. Engine not primed.
1. Move choke control to ON position.
2. Connect wire to spark plug.
3. Fill tank with clean, fresh gasoline.
4. Prime engine as instructed in the Operation
section.
5. Faulty spark plug.
5. Clean, adjust gap, or replace spark plug.
6. Insert key fully into the switch.
6. Safety key not inserted .
Engine runs erratic
1. Engine running on CHOKE.
2. Stale fuel.
1. Move choke control to OFF position.
2. Fill tank with clean, fresh gasoline.
3. Drain fuel tank. Refill with fresh fuel.
4. Contact a Tecumseh Engine Service Center.
3. Water or dirt in fuel system.
4. Carburetor out of adjustment.
Engine overheats
Excessive vibration
1. Carburetor not adjusted properly.
1. Loose parts or damaged auger.
1. Contact a Tecumseh Engine Service Center.
1. Stop engine immediately and disconnect
spark plug wire. Tighten all bolts and nuts. If
vibration continues, have unit serviced by an
authorized Service Center.
Loss of power
1. Spark plug wire loose.
1. Connect spark plug wire.
2. Gas cap vent hole plugged.
2. Remove ice and snow from gas cap. Be
certain vent hole is clear.
Unit fails to propel itself
Unit fails to discharge snow
1. Drive control cable in need of adjustment.
1. Adjust drive control cable. Refer to
Maintenance & Adjustments section.
2. Drive belt loose or damaged.
1. Chute assembly clogged.
2. Replace drive belt. Refer to Service section
1. Stop engine immediately and disconnect
spark plug wire. Clean chute assembly and
inside of auger housing with clean-out tool
or a stick.
2. Foreign object lodged in auger.
2. Stop engine immediately and disconnect
spark plug wire. Remove object from auger
with clean-out tool or a stick.
3. Auger control cable in need of adjustment.
3. Adjust auger control cable. Refer to Assembly
& Set-Up section.
4. Auger belt loose or damaged.
5. Shear pin(s) sheared.
4. Replace auger belt refer to Service section.
5. Replace shear pin(s).
ꢀꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
Replacement Parts
9
Part Number
Component
Description
30 Inch
33 Inch
Extention Cord, 110V
929-0071
929-0071
Auger Drive Belt
Wheel Drive Belt
954-04131
954-0367
954-0222A
954-0131
Friction Wheel Assembly
918-04178
718-04034
918-04178
718-04034
Friction Wheel w/Bonded Rubber
Lamp, 12V, (#1141)
925-1629
925-1629
Shear Pin, 1.50
738-04155
714-04040
738-04155
714-04040
Bow-tie Cotter Pin
Slide Shoe, Stainless Steel
Chute Clean-out Tool
790-00199
731-2643
790-00199
731-2643
Shave Plate, Stainless
790-00277
TC-35062
790-00196A
TC-35062
Key
759-3338
TC-34645
Resistor Spark Plug
Champion RJ19LM
Champion RN4C
Phone (800) 965-4CUB (4282) to order replacement parts or a complete Parts Manual (have your full model number and
ꢀ3
Download from Www.Somanuals.com. All Manuals Search And Download.
CUB CADET LLC
MANUFACTURER’S LIMITED WARRANTY FOR
SNOW THROWERS
The limited warranty set forth below is given by Cub Cadet LLC with
c. Cub Cadet does not extend any warranty for products sold or
exported outside of the United States and/or Canada, and their
respective possessions and territories, except those sold through
Cub Cadet’s authorized channels of export distribution.
respect to new merchandise purchased and used in the United States,
its possessions and territories, and by MTD Products Limited with
respect to new merchandise purchased and used in Canada and/or its
territories and possessions.
d. Replacement parts that are not genuine Cub Cadet parts.
For non-commercial use: Cub Cadet warrants this product (excluding
Normal Wear Parts, as described below) against defects in material
and workmanship for a period of three (3) years from the date of
original retail purchase or lease.
e. Service completed by someone other than an authorized service
dealer.
f. Transportation charges and service calls.
For commercial uses and applications: Cub Cadet warrants this
product (excluding Normal Wear Parts, as described below) against
defects in material and workmanship for a period of one (1) year from
the date of original retail purchase or lease.
No implied warranty, including any implied warranty of mer-
chantability of fitness for a particular purpose, applies after the
applicable period of express written warranty above as to the
parts as identified. No other express warranty, whether written
or oral, except as mentioned above, given by any person or
entity, including a dealer or retailer, with respect to any product,
shall bind Cub Cadet. During the period of the warranty, the
exclusive remedy is repair or replacement of the product as set
forth above.
The provisions as set forth in this warranty provide the sole and
exclusive remedy arising from the sale. Cub Cadet shall not be
liable for incidental or consequential loss or damage including,
without limitation, expenses incurred for substitute or replace-
ment lawn care services or for rental expenses to temporarily
replace a warranted product.
“Cub Cadet” will, at its option, repair or replace, free of charge, any
part found to be defective in materials or workmanship. This limited
warranty shall only apply if this product has been operated and
maintained in accordance with the Operator’s Manual furnished with
the product, and has not been subject to misuse, abuse, neglect,
accident, improper maintenance, alteration, vandalism, theft, fire,
water, or damage because of other peril or natural disaster. Damage
resulting from the installation or use of any part, accessory or
attachment not approved by Cub Cadet for use with the product(s)
covered by this manual will void your warranty as to any resulting
damage.
Normal Wear Parts are warranted to be free from defects in material
and workmanship for a period of thirty (30) days from the date of
purchase. Normal wear parts include, but are not limited to items
such as: belts, skid shoes, shave plates and tires.
Some states do not allow the exclusion or limitation of incidental
or consequential damages, or limitations on how long an implied
warranty lasts, so the above exclusions or limitations may not apply
to you.
HOW TO OBTAIN SERVICE: Warranty service is available, WITH
PROOF OF PURCHASE, through your local authorized service
dealer. To locate the dealer in your area:
In no event shall recovery of any kind be greater than the amount
of the purchase price of the product sold. Alteration of safety
features of the product shall void this warranty. You assume the
risk and liability for loss, damage, or injury to you and your property
and/or to others and their property arising out of the misuse or
inability to use the product.
In the U.S.A.
To locate the dealer in your area, check your Yellow Pages, or contact
Cub Cadet LLC at P.O. Box 361131, Cleveland, Ohio 44136-0019, or
com.
This limited warranty shall not extend to anyone other than the
original purchaser or to the person for whom it was purchased as a
gift.
In Canada
Contact MTD Products Limited, Kitchener, ON N2G 4J1, or call
com.
HOW STATE LAW RELATES TO THIS WARRANTY: This limited
warranty gives you specific legal rights, and you may also have other
rights that vary in different jurisdictions.
This limited warranty does not provide coverage in the following
cases:
IMPORTANT: Owner must present Original Proof of Purchase to
obtain warranty coverage.
a. The engine or component parts thereof. These items may
carry a separate manufacturer’s warranty. Refer to applicable
manufacturer’s warranty for terms and conditions.
b. Routine maintenance items such as lubricants, filters, blade
sharpening, tune-ups, brake adjustments, clutch adjustments,
deck adjustments, and normal deterioration of the exterior finish
due to use or exposure.
Cub Cadet LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019; Phone: 1-877-282-8684
MTD Canada Limited - KITCHENER, ON N2G 4J1; Phone 1-800-668-1238
GDOC-100093 REV. A
Download from Www.Somanuals.com. All Manuals Search And Download.
|