Instructions for the Use and Care and Installation of
BFWM7
7Kg Front Load Washing Machine
Download from Www.Somanuals.com. All Manuals Search And Download.
C O N T E N T S
Part 5:
Program Selection and Washing
Machine Operation
Part 1:
Technical features.
Part 2:
Steps before operating Fullautomatic
Washing Machine and safety precautions.
Part 6:
Care and Maintenance
Part 7:
Before Calling Service
Part 3:
Determining Location and Installation
Part 4:
Preparation
Download from Www.Somanuals.com. All Manuals Search And Download.
General Warnings.
• The appliance is not intended for use by young children or infirm persons without supervision.
• Young children should be supervised to ensure that they do not play with the appliance.
• If the appliance installed above carpet, please ensure that the carpet does not obstruct the
openings
• If the supply cord is damaged, it must be replaced by the manufacturer or its service agent or
a similarly qualified person in order to avoid a hazard.
• CAUTION: If the appliance is supplied from a cord extension set or an electrical outlet device,
the cord extension socket or electrical portable outlet device must be positioned so that it is
not subject to splashing or ingress
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Te c h n i c a l f e a t u r e s
Part 1:
Top lid
Control panel
Capacity (dry fabric)
7 kg.
Height
85 cm.
Width
60 cm.
Depth
59 cm.
Net weight
Power requirement
Nominal current
Power
76 kg.
240 V, 50 Hz.
10 A.
Front door
2350 Watts.
52 rpm.
1200 rpm.
Washing speed
Spin speed
The appearance and specifications are subject
to change without notice to raise the unit
quality.
Kick plate
The graphics shown in the manual are
schematic and it is possible that they not
conform with your washing machine.
Kick plate cover
Download from Www.Somanuals.com. All Manuals Search And Download.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Determining location and installation
Part 3:
1. Removing transport safety bolts at the rear of the machine
The transport safety bolts must
be removed before any operation
of the machine. Bolt heads,
marked “C”.
Remove transport safety bolts
and rubber bushes by pulling
outwards. (A up/down action
and a small squirt of washing
up liquid should ease removal.)
Plastic plugs, supplied
inside the protective bag
and designated as “P”,
should be placed in the
safety bolt holes according
to the direction shown.
“C”, should be turned in a
anti clockwise direction
until the bolt can be
partially withdrawn.
Attention!
Please keep the safety bolts for future transportationand reinstate them before transporting your machine. Never
transport your machine without the transport bolts in position.
Never place your machine on a carpet. This prevents air circulation. The electrical components of the machine
may overheat and may cause damage.
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Electrical connection
b) Water drain hose
Water drain hose could be placed either at the side of the laundry tub, or
directly to the drain. The hose should not be bent. Water drain hose should
be secured with the elbow so that it would not fall down on the ground.
Connect the power cord to the appropirate electrical
system which is being supported by the maximum
voltage and current rating indicated on the rating
plate placed inside the kick plate.
Note! Page 1, Steps before operating fully automatic
Washing Machine and safety precautions.
The hose should be placed between 40 and
100 cm. from the ground.
Water drain hose could be
placed directly to the drain
water inlet.
Download from Www.Somanuals.com. All Manuals Search And Download.
6
P reparation
Part 4:
Attention! Before any operation of the machine check the following.
Did you close the front door?
Is the tap open?
Is water drain hose placed properly?
Is power connected?
Sorting laundry
Sort the laundry according to the following groups and wash them seperately:
- white and resistant colored fabrics,
- colored fabrics,
- delicate fabrics (silk, rayon etc.),
- wool.
Be sure to empty pockets and remove any belts, buttons, pins, etc. from the clothing. You can place smaller garments
(baby socks, etc) inside of pillow cases to avoid them slipping into the pump and filter. For stained fabrics, refer to the
“Practical information” section of the operating manual.
To open the front door
press the “door open” button.
For your safety, front door can be opened only when the machine is off.
Loading the machine
Place the garments uniformly inside the machine. Hand knits should be placed inside out in the machine. Make sure that there
is no clothing at the side of the door. Close the door by pushing lightly. If the door does not close completely, the machine could
will not start, this is a safety measure. The door is locked until the end of the washing program and it cannot be re-opened until
about 2 minutes following the end of the program.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Detergent and softener selection
Choose the appropirate detergent specifically used for FRONT LOAD washing machines. Suggested amount is given on the
detergent cover.
Do not attempt to use detergents and bleaching elements that contain chlorine and sulphur. The amount of the detergent
depends on the dirt level of fabric, the amount of fabric and the softness of the water.
Detergent Dispenser
a. Compartment I. detergent compartment for prewash cycle.
b. Compartment II. detergent compartment for wash cycle.
c. " " Compartment for fabric conditioner.
d. Siphon.
WARNING!
When the CURTAIN program is selected Pre-wash function is automatically set. Pre-wash
can be operated even without detergent.
Attention! Fill the softener according to the supplier recommendation (app. <100 ml).
Do not exceed the “MAX level” marked on the detergent dispenser.
Download from Www.Somanuals.com. All Manuals Search And Download.
8
Control Panel
Quick wash
Program follower
Remain time
Prewash
Program selection knob
On/Off Button
Door open button
Rinse Plus
Timedelay
adjustment button
Spin speed
selection
Detergent drawer
Anti Creasing
Start/Pause/Cancel
button
Download from Www.Somanuals.com. All Manuals Search And Download.
9
Functions
Prewash
A pre-wash is only worth while with heavily soiled laundry. Without prewash you save energy, water, washing powder and time.
Quick wash
Shortens washing time for lightly soiled fabrics. This function can be used for cotton and synthetic programs for temperatures below 60° C.
Rinse plus
By using this function your machine will add another rinse process to the three rinse processes that it has already done. This additional
rinse will reduce any affects on sensitive skin by washing leftover detergent.
Anti Creasing
To avoid wrinkling of your clothes, select this function. When Anti-Creasing is choosen please load less cloth, this way a special washing and
spinning profile will reduce the wrinkles and your clothes will be easy to iron.
Spin Speed Selection
Using this button, you can select final spin speed upto 1200 rpm. If you do not want to apply spinning to your clothes, select “No Spin” option.
Rinse Hold
If you desire to leave your synthetic and wool fabrics in the machine after the wash program you may select the Rinse hold option to prevent
them getting wrinkled. If you want to cancel the “Rinse Hold” function, you have to press on “Start/Pause/Cancel” button first, select the desired
spin speed and then repress on the “Start/Pause/Cancel” button.
Download from Www.Somanuals.com. All Manuals Search And Download.
10
Program Selection and Washing Machine Operation
Part 5:
Insert the plug. Press the On/Off button and then the Door Open button. Open the door. Place your laundry into the machine according
to the recommended load capacity and close the front door.
Select the proper program according to the dirt strength and the thermostat value by means of Program Selection Table given on the
following pages.
Turn the program selection knob and set the desired program. Select the spin speed according to the desired program. Select desired
auxiliary functions.
Then, fill the fabric softener and the detergent into the related compartments, and close the detergent dispenser box. Push the Start/Pause
button to operate your machine. In the mean time the Start/Pause LED
of the program follower.
will be on. You can follow the washing steps by means
2
6
4
1
5
3
7
8
II
I
11
9
10
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Program selection
Max
Load
(kg)
Detergent
Hold Creasing Dispenser
Quick Rinse Rinse Anti-
Wash Plus
Fabric type
Programme
Cotton 90
Heavy soiled fabrics made from cotton or linen,
heat resistant
Normal soiled fabrics made from cotton or linen,
heat resistant
Lightly soiled fabrics made from cotton, non-color
fast
Heavy soiled fabrics made from cotton or linen,
heat resistant
•
7
7
139
140
142
175
103
100
81
55
49
49
70
50
50
50
65
60
50
50
40
50
15
_
2.26
1.19
0.50
1.35
1.02
0.50
0.16
0.55
0.35
0.35
0.04
0.15
0.15
0.12
0.1
I+II
I+II
I+II
II
•
•
•
•
•
•
•
•
•
*
•
•
•
*
•
•
•
•
•
•
•
•
•
•
•
•
•
•
(capacity 2.5kg)
•
Cotton 60*
(capacity 2.5kg)
•
7
Cotton 40
(capacity 2.5kg)
•
7
Intensive 60
Synthetics 60
Synthetics 40
Synthetics 30
(capacity 2.5kg)
Normal soiled fabrics made from cotton/synthetics
blended, heat resistant
•
3
I+II
I+II
I+II
I+II
II
•
•
•
•
•
•
*
(capacity 1.5kg)
Lightly Soiled Easy care fabrics made from cotton,
synthetics or blended fabrics (non-color fast)
Very Lightly Soiled Easy care fabrics made from
cotton, synthetics or blended fabrics (non-color fast)
•
3
(capacity 1.5kg)
•
3
(capacity 1.5kg)
2
115
62
Curtain 40 Special programme for curtains
*
(capacity 2kg)
Sensitive, easy care fabrics made from cotton,
synthetics or blended fabrics
•
2
Delicate 40
Woollen 40
(capacity 1kg)
II
1.5
1.5
1
55
Hand wash marked easy care, blended fabrics
Hand wash marked wool and easy care, blended
fabrics
II
48
Woollen Cold
Handwash 30
Special programme for Hand wash marked wool
and silk
II
40
II
Mini 30 Lightly Soiled less amount fabric
Rinse Rinsing
2.5
7
30
-
23
Spin Spinning
-
7
19
Drain Draining
-
-
2
_
_
Depending on water, textile and ambient conditions the actual values given on or with the machine can deviate from the declared standard values,
as they are tested according to the laboratory conditions
Download from Www.Somanuals.com. All Manuals Search And Download.
12
Child Lock
To prevent the knobs from being played with by your children you may activate “child lock” option. Activating the “Child Lock” option
prevents any change from being made to a set program.
To activate child lock, press both on the second and the fourth auxiliary function buttons together for 3 seconds after the machine
starts the washing operation.
After activating the Pre-wash auxiliary function, the LED will blinking.
Only On/Off button will be in operation when the child lock option is selected.
To deactivate child lock, re-press same auxiliary function buttons (second and fourth) for 3 seconds.
In order to open the door at the end of the washing program or to change program selection, child lock must be deactivated if
selected.
When the machine is turned on, the LED of the selected program will light up.
If there is no light on the program selection knob, it means that program selection knob is stuck between two
programs. In that case, the knob should be adjusted on the correct program again.
If the program selection knob is turned while the machine is on and executing the selected program , all LED on
the program selection knob will be off. When the knob is set to selected program again, related LED will be on.
Download from Www.Somanuals.com. All Manuals Search And Download.
13
On/Off
When you press the On/Off button, your machine is ready to select the desired
program. The “door open” LED will be on and the door is ready to open. When the
desired program is selected, related spin speed can be adjusted and the duration
of the program can be observed on the display. To switch the machine off, repress
the On/Off button.
Washing can only then be started when the
button is pressed.
Pressing the On/Off button does not mean that the washing operation is started!
To start the washing, press the Start/Pause button!
Auxiliary Function Selection
It is not possible to activate all auxiliary functions in all wash programs. If any auxiliary function is selected, its LED will be on.
It is restricted to select some auxiliary functions together. For example, if the cotton program is selected, “quick wash” and “pre-wash”
functions can not be selected at the same time. If “Pre-wash” button is selected first and the “Quick wash” function next, the LED of
the pre-wash function will be off as it is not active any more.
Program Follower
If the machine is on, a program can be followed by means of the program follower. If a washing step is over and the next step is started,
the LED of the previous step will continue to light.
It means if the washing operation is finished, all related washing steps on the program follower will be on.
Pre-wash button LED will be on, only if this auxiliary function is selected.
Additional Laundry
Press the Start/Pause button. If the water level does not exceed the limitations, in 1 to 2 minutes door open LED will come on. It means
the washing machine is ready to add laundry.
If door open LED is not lit up after 1-2 minutes, it means the water level inside the machine is too high and you will not be able to open
the door and add laundry. (Look at Program Cancelling).
If you change your mind and decide not to add laundry, press Start/Pause button again to let the program continue.
Download from Www.Somanuals.com. All Manuals Search And Download.
14
End of the Program
If all the wash programs are finished, all the LEDs on the program follower will be on . “1-2 minutes” for door open is displayed on remain
time display. After1-2 min door open LED will light up.
At the end of the washing, all related LEDs on the control panel will be on. Related duration time of the selected program is displayed
and the machine is ready to start again.
To switch off the machine, press the On/Off button.
Unloading the machine
Machine stops automatically after all the programs are finished. Turn off the tap. In 1-2 min, after the door open LED lights up, press the
door open button and open the door. Press the On/Off button to switch off the machine.
Unload the machine and leave the front door open. Check to see if there is any water left in the door hood. If so, remove with a soft cloth.
Download from Www.Somanuals.com. All Manuals Search And Download.
15
Time Delay
By using the time delay buttons, starting time of any program can be delayed. Time delay can be set at intervals of 30 min.
On the display, the delayed starting time is added to the duration of the program.
For example, if the program duration is 2 hours and 16 min and you delayed the program for 2 hours, the display will show “4:16”. After
the time delay is set, press Start/Pause button. The washing period will be started after 2 hours
Program Cancelling
If the program has not started yet, you can cancel the selected program by pressing Start/Pause button for 3 seconds. After 3 seconds
the LED of the Start/Pause button will be off and the LED of the selected program will be on, where it is possible to set a new program
If the program has started and you want to cancel it, press Start/Pause button for 3 seconds. The program will move to the “spin” step
and related LED on the program follower will be on. Machine will start to pump for draining and the door can be opened after the door
open LED is on.
Download from Www.Somanuals.com. All Manuals Search And Download.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Cleaning the pump filter
Remove the electrical power plug. Open the open the Kick plate
cover located at the bottom right side of the machine
by pushing on the marked area shown beside.
Attention! Hot water danger! It is possible that app.
15 lt, 90˚C hot water is inside. Be careful while taking
out the filter!
Before taking out the filter, drain the water by means of pump drain
hose. Take out the pump drain hose from its place. Place a shallow
container under the pump hose to catch the water. Remove the drain
pump hose plug and drain the water.
When all water is discharged, insert the plug into the pump hose
again and replace the pump drain hose in its place.
Open the filter while turning it counterclockwise, drain the left water
(max 30 ml) on to the filter cover. If there are any residual parts inside
the filter, take them out and clean the filter before replacing it. Then,
place the filter while turning it clockwise and at the end, close the
filter cover by pushing on the marked area again.
Attention! The filter and hose plug must be replaced
correctly. Ensure there is no lint around the seal of the
filter which could cause leaking.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Before calling service
Part 7:
You turned the machine on, but the LEDs do not light
up on the panel.
Check that the power cord is plugged in and power is
turned on or a blown fuse. Check the front in closed
properly closure.
Water coming from beneath the machine.
Check the water intake and drain hoses. Tighten the connections.
The washers of the hoses may be worn out. If non of the two,
the pump filter is not closed properly.
Foam coming out of the detergent dispenser.
Check whether your detergent is suitable for FRONT LOAD machines.
Next time use less detergent.
Machine does not take water.
Check the front door for proper closure. Either taps are
closed or water intake filters are clogged.
Pump does not drain water.
Clean the pump filter. Check whether the drain hose is bent or
not. If there is need to clean the pump filter, refer to the pump
filter cleaning section of the manual.
Taken water is directly discharged.
Check if the discharge hose placed as described in the
users manual or not.
Descriptions of the international textile care label (ITCL) symbols
P
A
60°
Washing
temperature
Bleach can
be used
Do not use
bleach
Do not machine
wash
Dry on horizantal
surface
Do not wash
Dry clean
Chemicals can
be used
No dry cleaning
No spin
Can be washed
at centrifugal
machine
Do not wash
centrifugal
machine
Line dry
Iron permitted
Do not iron
Warm iron
Download from Www.Somanuals.com. All Manuals Search And Download.
19
Blanco Contact Information.
NEW SOUTH WALES
SOUTH AUSTRALIA & NORTHERN TERRITORY
Agent and Sales Office
S C Lighting & Electrical Supplies
47 North Terrace
Head Office, Sales & Marketing Office
104 Vanessa Street
Hackney SA 5069
Kingsgrove NSW 2208
Telephone:
Facsimile:
Telephone:
Facsimile:
08 8362 4599
08 8362 4591
02 9503 2888
02 9503 2810
Service and Spare Parts
NSW Showroom*
40 Ebley Street
Bondi Junction NSW 2022
Telephone:
Prestige Appliance Repair Centre
Telephone:
Facsimile:
08 8352 2022
08 8352 3044
02 9386 1190
02 9386 1671
Facsimile:
WESTERN AUSTRALIA
Agent and Sales Office.
Hi –Performance Marketing
7 Coleman Street
Mascot NSW 2020
Telephone:
Agent and sales Office
Elite Appliance Marketing Pty Ltd
Suite 4
14 Main Street
Osborne Park WA 6017
02 88354937
02 90048739
Facsimile:
Telephone:
Facsimile:
08 9201 0311
08 9201 0366
Service and Spare Parts
All General Whitegoods Service
Service and Spare Parts
Telephone:
Facsimile:
02 8788 8666
02 9756 1091
Metropolitan Appliance Repairs
Telephone:
Facsimile:
08 9330 1724
08 9317 1296
AUSTRALIAN CAPITAL TERRITORY
TASMANIA
Service and Spare Parts
Detlevs Appliance & Electrical Care
1/88 Sheppard Street
Hume
Agent and Sales Office
Mark Pearce Agencies
23 Tranmere Road
ACT 2905
Howrah TAS 7018
Telephone:
Facsimile:
02 6280 1033
02 6260 1035
Tel/Fax: 03 6247 9215
VICTORIA
Service and Spare Parts
Electrical Equipment Service (Launceston)
State Office and Showroom*
35 Centre Road
Telephone:
Facsimile:
03 6339 3873
03 6339 4588
Scoresby VIC 3179
Telephone:
Facsimile:
03 8756 7888
03 8756 7907
Baldocks Appliance Service (Hobart)
Telephone:
Facsimile:
03 6234 5995
03 6234 8134
Service and Spare Parts
Advantage Appliances
Telephone:
03 9874 4222
03 9874 6917
Facsimile:
QUEENSLAND
BLANCO CUSTOMER SERVICE
1300 739 033
State Office and Showroom*
148 Robinson Road - East
Geebung
QLD 4034
Website: www.meaappliances.com.au
Telephone:
Facsimile:
07 3259 2500
07 3265 6933
* Showrooms open six days a week
Endeavour Appliances
Telephone:
Facsimile:
07 3872 7444
07 3852 2465
Platinum Appliance Service.
Telephone:
Facsimile:
07 38621154
07 38621114
Download from Www.Somanuals.com. All Manuals Search And Download.
|