HP146F4L
HP186F4L
HP148F4L
HP188F4L
Download from Www.Somanuals.com. All Manuals Search And Download.
A
C
E
B
D
F
Download from Www.Somanuals.com. All Manuals Search And Download.
3
G
4
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Personal safety
Intended use
a. Stay alert, watch what you are doing and use common
sense when operating a power tool. Do not use a power
tool while you are tired or under the influence of drugs,
alcohol or medication. A moment of inattention while
operating power tools may result in serious personal injury.
b. Use personal protective equipment. Always wear eye
protection. Protective equipment such as dust mask,
non-skid safety shoes, hard hat, or hearing protection used
for appropriate conditions will reduce personal injuries.
c. Prevent unintentional starting. Ensure the switch is in
the off-position before connecting to power source and/
or battery pack, picking up or carrying the tool. Carrying
power tools with your finger on the switch or energising
power tools that have the switch on invites accidents.
d. Remove any adjusting key or wrench before turning
the power tool on. A wrench or a key left attached to a
rotating part of the power tool may result in personal injury.
e. Do not overreach. Keep proper footing and balance at
all times. This enables better control of the power tool in
unexpected situations.
Your Black & Decker drill/screwdriver has been designed for
screwdriving applications and for drilling in wood, metal, plastics
and soft masonry. This tool is intended for consumer use only.
Safety instructions
General power tool safety warnings
Warning! Read all safety warnings and all
@
instructions. Failure to follow the warnings and
instructions listed below may result in electric shock,
fire and/or serious injury.
Save all warnings and instructions for future reference.
The term "power tool" in all of the warnings listed below refers
to your mains operated (corded) power tool or battery
operated (cordless) power tool.
1. Work area safety
a. Keep work area clean and well lit. Cluttered or dark
areas invite accidents.
b. Do not operate power tools in explosive atmospheres,
such as in the presence of flammable liquids, gases
or dust. Power tools create sparks which may ignite the
dust or fumes.
c. Keep children and bystanders away while operating a
power tool. Distractions can cause you to lose control.
f. Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves away
from moving parts. Loose clothes, jewellery or long hair
can be caught in moving parts.
g. If devices are provided for the connection of dust
extraction and collection facilities, ensure these are
connected and properly used. Use of dust collection can
reduce dust-related hazards.
2. Electrical safety
4. Power tool use and care
a. Power tool plugs must match the outlet. Never modify
the plug in any way. Do not use any adapter plugs
with earthed (grounded) power tools. Unmodified plugs
and matching outlets will reduce risk of electric shock.
b. Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric shock
if your body is earthed or grounded.
a. Do not force the power tool. Use the correct power tool
for your application. The correct power tool will do the job
better and safer at the rate for which it was designed.
b. Do not use the power tool if the switch does not turn it
on and off. Any power tool that cannot be controlled with
the switch is dangerous and must be repaired.
c. Disconnect the plug from the power source and/or the
battery pack from the power tool before making any
adjustments, changing accessories, or storing power
tools. Such preventive safety measures reduce the risk of
starting the power tool accidentally.
d. Store idle power tools out of the reach of children and
do not allow persons unfamiliar with the power tool or
these instructions to operate the power tool. Power
tools are dangerous in the hands of untrained users.
e. Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and any
other condition that may affect the power tools
operation. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly
maintained power tools.
c. Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of
electric shock.
d. Do not abuse the cord. Never use the cord for carrying,
pulling or unplugging the power tool. Keep cord away
from heat, oil, sharp edges or moving parts. Damaged
or entangled cords increase the risk of electric shock.
e. When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of a cord
suitable for outdoor use reduces the risk of electric shock.
f. If operating a power tool in a damp location is
unavoidable, use a residual current device (RCD)
protected supply. Use of an RCD reduces the risk of
electric shock.
Download from Www.Somanuals.com. All Manuals Search And Download.
5
u Before drilling into walls, floors or ceilings, check for the
location of wiring and pipes.
u Avoid touching the tip of a drill bit just after drilling, as it
may be hot.
f. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are less
likely to bind and are easier to control.
g. Use the power tool, accessories and tool bits etc. in
accordance with these instructions, taking into
account the working conditions and the work to be
performed. Use of the power tool for operations different
from those intended could result in a hazardous situation.
u This tool is not intended for use by persons (including
children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction
concerning use of the appliance by a person responsible
for their safety. Children should be supervised to ensure
that they do not play with the appliance.
u The intended use is described in this instruction manual.
The use of any accessory or attachment or performance
of any operation with this tool other than those
recommended in this instruction manual may present a
risk of personal injury and/or damage to property.
5. Battery tool use and care
a. Recharge only with the charger specified by the
manufacturer. A charger that is suitable for one type of
battery pack may create a risk of fire when used with
another battery pack.
b. Use power tools only with specifically designated
battery packs. Use of any other battery packs may create
a risk of injury and fire.
c. When battery pack is not in use, keep it away from
other metal objects, like paper clips, coins, keys,
nails, screws, or other small metal objects, that can
make a connection from one terminal to another.
Shorting the battery terminals together may cause burns
or a fire.
d. Under abusive conditions, liquid may be ejected from
the battery; avoid contact. If contact accidentally
occurs, flush with water. If liquid contacts eyes,
additionally seek medical help. Liquid ejected from the
battery may cause irritation or burns.
Vibration
The declared vibration emission values stated in the technical
data and the declaration of conformity have been measured in
accordance with a standard test method provided by
EN 60745 and may be used for comparing one tool with
another. The declared vibration emission value may also be
used in a preliminary assessment of exposure.
Warning! The vibration emission value during actual use of
the power tool can differ from the declared value depending
on the ways in which the tool is used. The vibration level may
increase above the level stated.
6. Service
When assessing vibration exposure to determine safety
measures required by 2002/44/EC to protect persons regularly
using power tools in employment, an estimation of vibration
exposure should consider, the actual conditions of use and the
way the tool is used, including taking account of all parts of the
operating cycle such as the times when the tool is switched off
and when it is running idle in addition to the trigger time.
a. Have your power tool serviced by a qualified repair
person using only identical replacement parts. This will
ensure that the safety of the power tool is maintained.
Additional power tool safety warnings
Warning! Additional safety warnings for drills and
@
impact drills
Residual risks.
Additional residual risks may arise when using the tool which
may not be included in the enclosed safety warnings. These
risks can arise from misuse, prolonged use etc.
Even with the application of the relevant safety regulations
and the implementation of safety devices, certain residual
risks can not be avoided. These include:
u Injuries caused by touching any rotating/moving
parts.
u Injuries caused when changing any parts, blades or
accessories.
u Injuries caused by prolonged use of a tool. When
using any tool for prolonged periods ensure you take
regular breaks.
u Wear ear protectors with impact drills. Exposure to
noise can cause hearing loss.
u Use auxiliary handles supplied with the tool. Loss of
control can cause personal injury.
u Hold power tool by insulated gripping surfaces when
performing an operation where the cutting accessory
may contact hidden wiring or its own cord. Cutting
accessory contacting a "live" wire may make exposed
metal parts of the power tool "live" and shock the operator.
u Use clamps or another practical way to secure and
support the workpiece to a stable platform. Holding the
work by hand or against your body leaves it unstable and
may lead to loss of control.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
u Impairment of hearing.
u Health hazards caused by breathing dust developed
when using your tool (example:- working with wood,
especially oak, beech and MDF.)
2
Charging (green flashing light)
Defective battery
3
Labels on tool
The following pictograms are shown on the tool:
5
Electrical safety
Low mains supply
Warning! To reduce the risk of injury, the user must
read the instruction manual.
:
Additional safety instructions for batteries and
chargers
Your charger is double insulated; therefore no earth
#
wire is required. Always check that the mains
voltage corresponds to the voltage on the rating
plate. Never attempt to replace the charger unit with
a regular mains plug.
Batteries
u Never attempt to open for any reason.
u Do not expose the battery to water.
u Do not store in locations where the temperature may
exceed 40 °C.
u Charge only at ambient temperatures between 10 °C and
40 °C.
u If the supply cord is damaged, it must be replaced by the
manufacturer or an authorised Black & Decker Service
Centre in order to avoid a hazard.
u Charge only using the charger provided with the tool.
u When disposing of batteries, follow the instructions given
in the section "Protecting the environment".
Features
This tool includes some or all of the following features.
1. Variable speed switch
2. Forward/reverse slider
3. Chuck
Do not attempt to charge damaged batteries.
4. Mode selector / torque adjustment collar
5. Two-gear selector
6. Bit holder
Do not incinerate the battery.
7. Battery
7
Fig. A
8. Charger
Chargers
u Use your Black & Decker charger only to charge the
battery in the tool with which it was supplied. Other
batteries could burst, causing personal injury and damage.
u Never attempt to charge non-rechargeable batteries.
u Have defective cords replaced immediately.
u Do not expose the charger to water.
u Do not open the charger.
9. Charger receptacle
10. Charging indicator
Assembly
Warning! Before assembly, remove the battery from the tool.
Fitting and removing the battery (fig. B)
u To fit the battery (7), line it up with the receptacle on the
tool. Slide the battery into the receptacle and push until
the battery snaps into place.
u To remove the battery, push the release button (11) while
at the same time pulling the battery out of the receptacle.
u Do not probe the charger.
$
The charger is intended for indoor use only.
Read the instruction manual before use.
Battery too hot
Fitting the battery cap (fig. C)
Warning! Fit the cap (12) to the battery (7) for transportation
and storage.
4
1
Charging process completed (continuous green
light)
Download from Www.Somanuals.com. All Manuals Search And Download.
7
u If the new battery gives the same indication as the original
battery, take the charger to be tested at an authorised
services centre.
Fitting and removing a drill bit or screwdriver bit
(fig. D)
This tool is fitted with a keyless chuck to allow for an easy
Note: It may take as long as 15 minutes to determine that the
battery is defective. If the battery is too hot of too cold, the
LED will alternately blink fast and slow, one flash at each
speed and repeat.
exchange of bits.
u Lock the tool by setting the forward/reverse slider (2) to
the centre position.
u Open the chuck by turning it (3) with one hand while
holding the tool with the other.
Selecting the direction of rotation (fig. E)
For drilling and for tightening screws, use forward (clockwise)
rotation. For loosening screws or removing a jammed drill bit,
use reverse (counterclockwise) rotation.
u To select forward rotation, push the forward/reverse slider
(2) to the left.
u Insert the bit shaft (14) into the chuck.
u Firmly tighten the chuck by turning it (3) with one hand
while holding the tool with the other.
This tool is supplied with a double-ended screwdriver bit in the
bit holder (6).
u To remove the screwdriver bit from the bit holder, lift the bit
from the recess.
u To store the screwdriver bit, firmly push it into the holder.
u To select reverse rotation, push the forward/reverse slider
to the right.
u To lock the tool, set the forward/reverse slider into the
centre position.
Use
Warning! Let the tool work at its own pace. Do not overload.
Selecting the operating mode or torque (fig. F)
This tool is fitted with a collar to select the operating mode and
to set the torque for tightening screws. Large screws and hard
workpiece materials require a higher torque setting than small
screws and soft workpiece materials. The collar has a wide
range of settings to suit your application.
Charging the battery (fig. A)
Warning! Do not charge the battery at ambient temperatures
below 10 °C or above 40 °C. Recommended charging
temperature: approx. 24 °C.
u For drilling in wood, metal and plastics, set the collar (4) to
the drilling position by aligning the symbol with the
marking (15).
u For screwdriving, set the collar to the desired setting.
If you do not yet know the appropriate setting, proceed as
follows:
Note: The charger will not charge a battery if the cell
temperature is below approximately 0 °C or above 60 °C.
The battery should be left in the charger and the charger will
begin to charge automatically when the cell temperature
warms up or cools down.
u Plug in the charger (8) and switch on at the mains.
u Insert the battery (7) into the charger. Make sure that the
battery is fully seated in the charger (8).
The charging indicator (10) will flash continuously (slowly). The
charge is complete when the charging indicator (10) lights
continuously. The charger and the battery can be left connected
indefinitely with the LED illuminated. The LED will change to
flashing (charging) state as the charger occasionally tops off the
battery charge. The charging indicator (10) will be lit as long as
the battery is connected to the plugged-in charger.
-
-
-
Set the collar (4) to the lowest torque setting.
Tighten the first screw.
If the clutch ratchets before the desired result is
achieved, increase the collar setting and continue
tightening the screw. Repeat until you reach the correct
setting. Use this setting for the remaining screws.
HP148F4L/HP188F4 - Drilling in masonry (fig. F & G)
u For drilling in masonry, set the collar (4) to the hammer
drilling position by aligning the symbol with the marking
(15).
u Charge discharged batteries within 1 week. Battery life will
be greatly diminished if stored in a discharged state.
u Slide the two-gear selector (5) towards the front of the tool
(2nd gear).
Charging indicators
If the charger detects a problem with the battery, the charging
indicator (10) will flash at a fast rate. Proceed as follows:
u Re-insert the battery (7).
u If the charging indicators continues flashing at a fast rate,
use a different battery to determine if the charging process
works properly.
u If the replaced battery charges correctly, the original
battery is defective and should be returned to a service
centre for recycling.
Two-gear selector (fig. G)
u For drilling in steel and for screwdriving applications, slide
the two-gear selector (5) towards the rear of the tool (1st
gear).
u For drilling in materials other than steel, slide the two-gear
selector (5) towards the front of the tool (2nd gear).
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Drilling/screwdriving
u Select forward or reverse rotation using the forward/
Protecting the environment
reverse slider (2).
Separate collection. This product must not be
disposed of with normal household waste.
u To switch the tool on, press the switch (1). The tool speed
depends on how far you press the switch.
u To switch the tool off, release the switch.
Z
Should you find one day that your Black & Decker product
needs replacement, or if it is of no further use to you, do not
dispose of it with household waste. Make this product
available for separate collection.
Hints for optimum use
Drilling
u Always apply a light pressure in a straight line with the drill
bit.
u Just before the drill tip breaks through the other side of the
workpiece, decrease pressure on the tool.
u Use a block of wood to back up workpieces that may
splinter.
Separate collection of used products and packaging
z
allows materials to be recycled and used again.
Re-use of recycled materials helps prevent
environmental pollution and reduces the demand for
raw materials.
u Use spade bits when drilling large diameter holes in wood.
u Use HSS drill bits when drilling in metal.
u Use masonry bits when drilling in soft masonry.
u Use a lubricant when drilling metals other than cast iron
and brass.
Local regulations may provide for separate collection of
electrical products from the household, at municipal waste
sites or by the retailer when you purchase a new product.
Black & Decker provides a facility for the collection and
recycling of Black & Decker products once they have reached
the end of their working life. To take advantage of this service
please return your product to any authorised repair agent who
will collect them on our behalf.
u Make an indentation using a centre punch at the centre of
the hole to be drilled in order to improve accuracy.
Screwdriving
u Always use the correct type and size of screwdriver bit.
u If screws are difficult to tighten, try applying a small
amount of washing liquid or soap as a lubricant.
u Always hold the tool and screwdriver bit in a straight line
with the screw.
You can check the location of your nearest authorised repair
agent by contacting your local Black & Decker office at the
address indicated in this manual. Alternatively, a list of
authorised Black & Decker repair agents and full details of our
after-sales service and contacts are available on the Internet
at: www.2helpU.com
Maintenance
Your Black & Decker tool has been designed to operate over a
long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.
Batteries
Black & Decker batteries can be recharged many
Your charger does not require any maintenance apart from
regular cleaning.
Z
times. At the end of their useful life, discard batteries
with due care for our environment:
Warning! Before performing any maintenance on the tool,
remove the battery from the tool. Unplug the charger before
cleaning it.
u Regularly clean the ventilation slots in your tool and
charger using a soft brush or dry cloth.
u Run the battery down completely, then remove it from the
tool.
u NiCd, NiMH and Li-Ion batteries are recyclable. Take them
to any authorised repair agent or a local recycling station.
u Regularly clean the motor housing using a damp cloth. Do
not use any abrasive or solvent-based cleaner.
u Regularly open the chuck and tap it to remove any dust
from the interior.
Download from Www.Somanuals.com. All Manuals Search And Download.
9
Technical data
EC declaration of conformity
HP146F4L(H2)
HP148F4L(H2)
14.4
0-350/0-1,200
29
13
MACHINERY DIRECTIVE
Voltage
No-load speed
Max. torque
Chuck capacity
Max. drilling capacity
steel/wood/masonry
Battery cat. no.
Weight (without battery)
VDC 14.4
min-1 0-350/0-1,200
Nm 28
%
HP146F4L, HP148F4L, HP186F4L, HP188F4L
mm 13
Black & Decker declares that these products described under
"technical data" are in compliance with:
mm 13/19
A1514L
kg 1.33
13/19/13
A1514L
1.38
2006/42/EC, EN 60745-1, EN 60745-2-1
For more information, please contact Black & Decker at the
following address or refer to the back of the manual.
HP186F4L(H2)
VDC 18
HP188F4L(H2)
18
0-350/0-1,200
34
13
Voltage
No-load speed
Max. torque
Chuck capacity
Max. drilling capacity
steel/wood/masonry
Battery cat. no.
Weight (without battery)
min-1 0-350/0-1,200
Nm 33
The undersigned is responsible for compilation of the technical
file and makes this declaration on behalf of Black & Decker.
mm 13
mm 13/25
A1518L
kg 1.33
13/25/13
A1518L
1.38
Kevin Hewitt
Vice-President Global Engineering
Black & Decker Europe, 210 Bath Road, Slough,
Berkshire, SL1 3YD
_
Battery
Voltage
Capacity
Battery type
Weight
A1514L
VDC 14.4
Ah 1.5
Li-Ion
kg 0.45
A1518L
18
1.5
Li-Ion
0.44
United Kingdom
19/02/2010
Charger
905514-XX
VAC 230
VDC 21
Input voltage
Output Voltage
Current
A
3
Approx. charging time
Weight
min 40
kg 0.55
Level of sound pressure according to EN 60745:
Sound pressure (LpA) 87.7 dB(A), uncertainty (K) 3 dB(A)
Sound power (LWA) 98.7 dB(A), uncertainty (K) 3 dB(A)
Vibration total values (triax vector sum) according to EN 60745:
(ah, ID) 17.7 m/s2, uncertainty (K) 1.5 m/s2
Impact drilling into concrete
(ah, D) 1.32 m/s2, uncertainty (K) 1.5 m/s2
Drilling into metal
(ah, S) 0.64 m/s2, uncertainty (K) 1.5 m/s2
Screwdriving without impact
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Guarantee
Black & Decker is confident of the quality of its products and
offers an outstanding guarantee. This guarantee statement is
in addition to and in no way prejudices your statutory rights.
The guarantee is valid within the territories of the Member
States of the European Union and the European Free Trade
Area.
If a Black & Decker product becomes defective due to faulty
materials, workmanship or lack of conformity, within 24
months from the date of purchase, Black & Decker guarantees
to replace defective parts, repair products subjected to fair
wear and tear or replace such products to ensure minimum
inconvenience to the customer unless:
u The product has been used for trade, professional or hire
purposes;
u The product has been subjected to misuse or neglect;
u The product has sustained damage through foreign
objects, substances or accidents;
u Repairs have been attempted by persons other than
authorised repair agents or Black & Decker service staff.
To claim on the guarantee, you will need to submit proof of
purchase to the seller or an authorised repair agent. You can
check the location of your nearest authorised repair agent by
contacting your local Black & Decker office at the address
indicated in this manual. Alternatively, a list of authorised
Black & Decker repair agents and full details of our after-sales
service and contacts are available on the Internet at:
register your new Black & Decker product and to be kept up to
date on new products and special offers. Further information
on the Black & Decker brand and our range of products is
available at www.blackanddecker.co.uk
Download from Www.Somanuals.com. All Manuals Search And Download.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
13
14
Download from Www.Somanuals.com. All Manuals Search And Download.
ENGLISH
Do not forget to register your product!
Register your product online at www.blackanddecker.co.uk/productregistration or send your name, surname and product
code to Black & Decker in your country.
Download from Www.Somanuals.com. All Manuals Search And Download.
15
Australia
Black & Decker (Australia) Pty. Ltd.
20 Fletcher Road, Mooroolbark,
Victoria, 3138
Tel. 03-8720 5100
Fax 03-9727 5940
New Zealand
Black & Decker
5 Te Apunga Place
Mt Wellington
Tel. +64 9 259 1133
Fax +64 9 259 1122
Auckland 1060
United Kingdom
Black & Decker
210 Bath Road
Tel. 01753 511234
Fax 01753 551155
Helpline 01753 574277
Slough, Berkshire SL1 3YD
90561597 REV-0
02/2010
Download from Www.Somanuals.com. All Manuals Search And Download.
|