User Manual
Wireless CardBus
Notebook Adapter
WLI-CB-G54S
Download from Www.Somanuals.com. All Manuals Search And Download.
v2.0
www.buffalotech.com
Getting Started
• Insert the AirNavigator CD
into the CD-ROM drive of your
computer. The AirNavigator
Setup Wizard should launch
automatically.
• To launch the AirNavigator
Setup Wizard manually, click
Start, then Run. Type “D:\
Setup.exe”, where D is the drive
letter assigned to your CDrom.
• Click OK to launch the wizard.
Download from Www.Somanuals.com. All Manuals Search And Download.
ꢁ
Installing Wireless Drivers
• Select Install Wireless
Drivers.
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Installing Wireless Drivers
• Click Next to install a driver for the CardBus.
• Select Agree and click Next to continue the process after reviewing the license
agreemennt.
• A window will appear prompting the insertion of the Wireless CardBus Adapter. Firmly
insert the AirStation Card into a CardBus slot on your notebook.
Download from Www.Somanuals.com. All Manuals Search And Download.
5
Insert the Card
• Turn on your notebook PC. Insert the AirStation card, with the Buffalo logo facing up,
into an available CardBus slot. The Found New Hardware Wizard will launch.
• Select Install the software automatically. Click Next.
Download from Www.Somanuals.com. All Manuals Search And Download.
ꢂ
Installing Wireless Drivers
• Select the device you want to install. If multiple drivers are listed, select the most re-
cent driver version. Click the Next button.
• If a window opens, stating that your driver does not pass Windows Logo testing, click
the Continue Anyway button. When the Wireless Notebook Adapter is successfully
installed, click the Finish button. Restart your PC if prompted.
Download from Www.Somanuals.com. All Manuals Search And Download.
ꢃ
Connecting Wireless Clients to your Network
Buffalo supports three different
methods for connecting your wireless
client device to your network.
If your AP supports it, use the simple,
utterly secure AOSS to connect.
Install the Client Manager from your
AirNavigator CD (page 10) and turn to
page 13.
You may also use the Client Manager
software from your AirNavigator CD to
configure your network manually. See
page 18 for more on Client Manager.
If you’re running Windows XP on your
PC, you may use its built-in Zero
Configuration tool to connect to your
router/AP. See page 23 for more on
Zero Configuration.
Download from Www.Somanuals.com. All Manuals Search And Download.
ꢄ
Client Manager
Client Manager can be used to survey and connect to available access points, configure
WPA/WEP encryption, and create connection profiles.
Note: When Client Manager is installed, Windows XP Wireless Zero Configuration is
automatically disabled.
Installing Client Manager
Insert the AirNavigator CD into the CD-
ROM drive of you computer. If the Air
Navigator Setup Wizard does not launch
automatically, launch it manually by
clicking Start and then Run. Enter D:\
Setup.exe in the dialog box that appears.
Click OK. Select Install Wireless Client
Manager.
Download from Www.Somanuals.com. All Manuals Search And Download.
ꢅ
Client Manager
• Once the Client Manager Installer launches, click Next.
• Press Agree to accept the license agreement and continue installation.
Download from Www.Somanuals.com. All Manuals Search And Download.
10
Client Manager
• Click OK when Client Manager
installation is complete.
• Press Exit Setup to exit AirNavigator.
• Client Manager is now installed and
running. Right-click on its icon (the
black antenna) to use it.
Download from Www.Somanuals.com. All Manuals Search And Download.
11
Using AOSS
AOSS (AirStation One-Touch Secure
System) is a simple, one-touch setup for
connecting wireless clients to an access
point while enforcing the most secure
possible connection encryption type.
Users no longer need to worry about
choosing the proper security protocols,
IP addresses, or SSID. AOSS determines
the optimal connection and configures
itself in seconds. If your router doesn’t
support AOSS, turn to page 15 to
configure your connection manually
with Client Manager or page 22 to use
Wireless Zero Config.
The AOSS button for this wireless client is in its Client Manager software. Start
Client Manager by right clicking on the black antenna icon in your System Tray,
or by launching the Client Manager from your Start Menu: Programs >> Buffalo
>> AirStation Utility >> Client Manager.
Download from Www.Somanuals.com. All Manuals Search And Download.
1ꢀ
Using AOSS
• From the Status Screen, select the Profiles tab.
• Initiate AOSS by clicking the blue AOSS button on the Client Manager’s screen. The
AOSS wizard will appear.
• Now, press the AOSS button on the Access Point. Hold it down until the AOSS LED
begins to flash.
Download from Www.Somanuals.com. All Manuals Search And Download.
1ꢁ
Using AOSS
Once AOSS is complete (about 30 seconds), the connection is archived as a profile for later
use. To minimize Client Manager to the system tray, click the ‘X’ in the top right corner.
Notes:
AOSS will scan for an AOSS partner for about two minutes. If it times out before finding
one, just press the AOSS buttons again.
Output power is reduced to 25% of normal during AOSS for security reasons. If you’re
having trouble making an AOSS connection, temporarily move the devices closer together.
AOSS will automatically use the highest level of security available for all currently
connected wireless devices.
If you have trouble connecting with AOSS, temorarily disable all personal firewalls on your
PC, such as ZoneAlarm or Microsoft Personal Firewall. These programs may be re-enabled
after AOSS has finished.
Download from Www.Somanuals.com. All Manuals Search And Download.
14
Client Manager Configuration
You may use Client Manager to configure your wireless network. Client Manager consists
of the Status page, the Survey page, and the Profiles page. You can access each page by
clicking the corresponding button on Client Manager. In addition to these pages, several
dialog boxes are also available. You can access the Edit Profile dialog box, New Profile
dialog box, IP Configuration dialog box, or WEP Configuration dialog box using the Client
Manager pages. You may also initiate AOSS.
Status Page
Click Status to open this page. By
default, this page is displayed when
you start Client Manager. Details of
connection status are displayed.
This page only displays connection
information; no changes to settings are
made here.
This page includes the following
components:
• Adapter Name – Displays the part
number of the wireless adaptor that is
being used.
Download from Www.Somanuals.com. All Manuals Search And Download.
15
Client Manager Configuration
• Network Type - Displays whether network is in Ad-Hoc or Infrastructure mode.
• Rate – The speed of communication between wireless devices. If the Client Manager is
not connected to a remote wireless device (access point or another client), no rate will
be displayed.
• Channel – The channel that the two wireless clients are using for communication. If
the Client Manager is not connected to a remote wireless device, no channel will be
displayed. Channels 1-11 may be used.
• Security – The type of encryption in use. If the Client Manager is not connected to a
remote wireless device, then ‘No Encryption’ will be displayed.
• IP Address – The IP address of the machine the Client Manager is installed on. If the
Client Manager is not connected to a network with DHCP, then no IP address will be
displayed.
• MAC Address – The MAC address of the wireless client device inside the computer
Client Manager is installed on. If no wireless device is present in the computer, then no
MAC Address will be displayed.
• Signal Strength – Displays the signal strength of the peak signal level the wireless
adapter receives from the wireless device to which it is connected. Next to the signal
level is the wireless hardware being used for this measurement.
Download from Www.Somanuals.com. All Manuals Search And Download.
1ꢂ
Client Manager Configuration
Click the Scan tab to open this page. Here, you can survey the area, display available
access points, and connect to available access points.
This page includes the following components:
• Wireless SSID – The SSID is the “name” of
a wireless network. Each wireless device
on a network must use identical SSIDs to
successfully communicate.
• Wireless Mode – Displays available modes for
each available remote wireless device.
• Strength – Displays the relative signal strength of
the wireless networks.
• Encryption – Displays whether the wireless
network is using any sort of encryption.
Click Connect to connect to a highlighted SSID,
or Refresh to update the list of available wireless
devices.
Download from Www.Somanuals.com. All Manuals Search And Download.
1ꢃ
Client Manager Configuration
This dialog will open for you to enter any necessary encryption information.
The correct encryption type should already be
selected automatically in the Encryption Method
drop down list. Only change this setting if
necessary.
The Encryption Key is where the actual key for
the wireless network should be entered. Some
wireless networks allow you to enter multiple
keys; four separate fields are available for this. If
your network only uses one encryption key, then
please use the first field (#1) to enter your key.
The Register Profile option will store this
wireless network in your profiles. You will then
automatically connect to this network when
inside its range. This is recommended if you plan
on using this wireless network again.
Press the Connect button once you have completed entering encryption information.
Download from Www.Somanuals.com. All Manuals Search And Download.
1ꢄ
Client Manager Configuration
Profiles Page
Click the Profiles tab to open this page.
Use this page to access your profiles.
Profiles allow you to save the information
associated with a specific wireless
network so you can quickly and easily
connect to that network when you are in
that location. The Profiles page allows you
to add, delete, and edit your profiles, as
well as import and export data.
• Connect – Click the Connect button
to connect to the selected profile and
return to the Status page.
• Edit – Click the Edit button to edit the
selected profile’s settings. The Edit
button also allows you to delete profiles
that are no longer used or required.
• Add – Click the Add button to add a profile manually. You will need important
information such as SSID, encryption settings, and network type.
Download from Www.Somanuals.com. All Manuals Search And Download.
1ꢅ
Client Manager Configuration
New Profile Dialog Box
• Select Profile – Select whether the profile is for a wireless or
wired connection.
• Profile Name – Enter the name you want to associate with
the new profile.
• Network Type – Select the network mode you want to
associate with the new profile. Select Infrastructure if your
network consists of both wired and wireless devices that
communicate through a central device, such as an access
point. Select Ad-hoc if your network consists of only wireless
devices that communicate with each other directly.
• Network Name SSID – Enter the SSID of your network. The
SSID is the name of your wireless network. All wireless
devices on a network must use identical SSIDs to successfully associate with other devices on
the network. MYSSID is an example of a valid SSID.
• Channel – The channel setting is only used for Ad-hoc connections. When using an Ad-hoc
connection, select a channel and make sure the other Ad-hoc devices are configured to use the
same channel. Otherwise, use Auto-Channel.
• Encryption Method – Displays the types of encryption available. Once encryption is selected,
you will be required to enter an Encryption Key. For the Transmission Key Number, 1 is
recommended.
• OK – Click OK to save your specifications and return to the Profiles page.
Download from Www.Somanuals.com. All Manuals Search And Download.
ꢀ0
Client Manager Configuration
Advanced Profile Options
• Network Tab – Displays the network information tab. A static IP can be specified for
this wireless profile here. It is not recommended to change any of these settings unless
specified by an administrator.
• Browser Tab – Displays settings to change your browser preferences for this wireless
profile. A specific home page can be specified when connected to this wireless profile as
can specific proxy server addresses.
• Printers Tab – Displays the printers tab. A specific default printer can be associated to
this profile. Thus, when connected to this profile, a specific printer will be used as the
default printer.
• OK – Click the OK button to save your specifications and return to the Profiles page.
• AOSS Icon – To automatically add the USB wireless client to your network,
just click this icon and then hold down the AOSS button on your wireless
router for a few seconds.
Check your package for an AOSS Manual, which will give more information
on using AOSS.
Download from Www.Somanuals.com. All Manuals Search And Download.
ꢀ1
Zero Configuration Service
Windows XP includes the Zero Configuration Service, a
built in serrvice to configure your wireless clients from
within Windows. Turn to page 15 if you would rather use
Buffalo’s Client Manager to configure your wireless client.
• If the Wireless Zero Configuration Service is activated,
Windows will scan for available wireless access
points once the Wireless CardBus Adapter is properly
installed. If Windows detects one or more access
points, a networking icon appears within the system
tray. “One or more wireless networks are available”
will appear as a caption accompanying the icon.
• To start Wireless Zero Configuration manually, click
Start >> Control Panel >> Administrative Tools >>
Services. Select Automatic in the Startup Type field of
Wireless Zero Configuration Service.
• Right click the networking icon in the taskbar and
select View Available Wireless Networks. Select an
SSID and click Connect. You may need to check the
box indicating you are connecting to an unsecured
network. See page 23 if you need to enter an SSID
network name or WEP/WPA encryption key.
Download from Www.Somanuals.com. All Manuals Search And Download.
ꢀꢀ
Zero Configuration Service
• Click the Advanced tab to enter an SSID network name or WEP/WPA encryption key if
necessary. To add an SSID network name that is not listed, click Add.
Download from Www.Somanuals.com. All Manuals Search And Download.
ꢀꢁ
Zero Configuration Service
• To configure a WEP/WPA encryption key, select the
wireless network and click Configure.
• From the pull down menu, select the Network
Authentication and Data Encryption types for the
wireless network. Enter and confirm the Network
Key and Key Index. Click OK when finished.
Download from Www.Somanuals.com. All Manuals Search And Download.
ꢀ4
Antenna Information
• The WLI-CB-G54S comes with an external antenna connector. Buffalo Technology
sells numerous external antennas that are compatible with this card. The connector
type is called an MC-Card Connector. Adding an external antenna can further in-
crease the power and range of this device. Please see the Buffalo Technology Web Page
Download from Www.Somanuals.com. All Manuals Search And Download.
ꢀ5
Specifications
Wireless LAN Interface
Standards Compliance
IEEE 802.11g
Communication Protocol
Direct Sequence Spread Spectrum
(DS-SS), Half Duplex
Frequency Range
Transmission Rates
2.412-2.462Mhz
802.11g: 1, 2, 5.5, 11, 18, 24, 36, 48, 54
802.11b: 1, 2, 5.5, 11
Access Mode
Security
Infrastructure mode, Ad-Hoc
WEP 128/64 bit, 802.1x, WPA-TKIP/AES
Others
Interface
CardBus
Environmental Operation
0-55ºc, 20-80% (non-condensing)
Download from Www.Somanuals.com. All Manuals Search And Download.
ꢀꢂ
Troubleshooting / FAQ
Troubleshooting / FAQ
Use this section to locate answers to frequently asked questions.
What should I do if I already have a version of Client Manager on my PC?
Update your Client Manager to the version on the CD. If you do not update your Client
Manager, there could be a loss of functionally, as some versions of Client Manager will
not work properly with the G54 Wireless Notebook Adapter. Before updating Client
Manager, you must uninstall all previous versions of Client Manager. To update your
Client Manager, load the Air Navigator CD and select Install Client Manager.
Why won't all my network clients work?
Some operating systems support only a limited number of network clients.
Windows 98/Me: These operating systems support only four network clients. If you install
more than four network clients, only the first four clients you install will work.
Will Client Manager support all operating systems?
Client Manager and the Wireless Notebook Adapter currently support only Windows 98/
ME/2000/XP. They do not currently support Windows NT, Mac OS, or Linux. For more
information, refer to the Mac OS and Linux page in the Troubleshooting section of this
help file.
Download from Www.Somanuals.com. All Manuals Search And Download.
ꢀꢃ
Troubleshooting / FAQ
Where can I attach my external antenna?
Insert your external antenna into the antenna connector, located on the back of the G54
Wireless Notebook Adapter.
Why won't Client Manager function properly?
Windows XP – The Wireless Zero Configuration Service conflicts with Client Manager. Se-
lect Start»Control Panel»Administrative Tools»Services to open the Services window. Select
Disabled in the Startup Type field of Wireless Zero Configuration Service to disable the
Wireless Zero Configuration Service.
I have more than one Air Navigator CD. Do I need more than one CD?
No. You receive the same Air Navagator CD with each Buffalo Technology access point
and wireless adapter. The CDs are identical and you only need one copy.
Download from Www.Somanuals.com. All Manuals Search And Download.
ꢀꢄ
Glossary
10BaseT or 100BaseTx: 802.3 based Eth-
ernet network that uses UTP (Unshielded
twisted pair) cable and a star topology. 10
is 10 Mbps and 100 is 100 Mbps.
Client: A PC or workstation on a network.
Cross-Over Wiring: A UTP cable that has its
transmit and receive pair crossed to allow
communications between two devices.
802.1x: The standard for wireless LAN
authentication used between an AP and a
client. 802.1x with EAP will initiate key
handling.
DCE (Data Communications Equipment):
Hardware used for communication with a
Data Terminal Equipment (DTE) device.
Default Gateway: The IP Address of either
the nearest router or server for the LAN.
Ad-Hoc Network: The wireless network
based on a peer-to-peer communications
session. Also referred to as AdHoc.
Default Parameter: Parameter set by the
manufacturer.
Bandwidth: The transmission capacity of
a computer or a communication channel,
stated in Megabits per second (Mbps).
Destination Address: The address portion of
a packet that identifies the intended recipi-
ent station.
BSS (Basic Service Set): An 802.11 net-
working framework that includes an Access
Point.
DHCP (Dynamic Host Configuration Proto-
col): Based on BOOTP, it uses a pool of IP
addresses, which it assigns to each device
connected to it, and retrieves the address
when the device becomes dormant for a
period of time.
Bus Mastering: A system in which the spec-
ified Input/Output device (e.g. NIC Card)
can perform tasks without the intervention
of the CPU.
DNS (Domain Name System): System used
Download from Www.Somanuals.com. All Manuals Search And Download.
ꢀꢅ
Glossary
to map readable machine names into IP
addresses
stated in Megabits per second (Mbps).
BSS (Basic Service Set): An 802.11 net-
Driver: Software that interfaces a computer working framework that includes an Access
with a specific hardware device.
Point.
DSSS (Direct Sequence Spread Spectrum):
Method of spreading a wireless signal into
wide frequency bandwidth.
Bus Mastering: A system in which the spec-
ified Input/Output device (e.g. NIC Card)
can perform tasks without the intervention
of the CPU.
DTE (Data Terminal Equipment): Device that
con10BaseT or 100BaseTx: 802.3 based
Ethernet network that uses UTP (Unshield-
ed twisted pair) cable and a star topology.
10 is 10 Mbps and 100 is 100 Mbps.
Client: A PC or workstation on a network.
Cross-Over Wiring: A UTP cable that has its
transmit and receive pair crossed to allow
communications between two devices.
802.1x: The standard for wireless LAN
authentication used between an AP and a
client. 802.1x with EAP will initiate key
handling.
DCE (Data Communications Equipment):
Hardware used for communication with a
Data Terminal Equipment (DTE) device.
Default Gateway: The IP Address of either
the nearest router or server for the LAN.
Ad-Hoc Network: The wireless network
based on a peer-to-peer communications
session. Also referred to as AdHoc.
Default Parameter: Parameter set by the
manufacturer.
Bandwidth: The transmission capacity of
a computer or a communication channel,
Destination Address: The address portion of
Download from Www.Somanuals.com. All Manuals Search And Download.
ꢁ0
Glossary
a packet that identifies the intended recipi-
ent station.
in a TCP/IP network, typically by a DHCP
server.
DHCP (Dynamic Host Configuration Proto-
col): Based on BOOTP, it uses a pool of IP
addresses, which it assigns to each device
connected to it, and retrieves the address
when the device becomes dormant for a
period of time.
ESS (Extended Service Set): A set of two or
more BSSs that form a single sub-network.
ESS-ID is user identification used in the
ESS LAN configuration.
Ethernet: The most widely used architec-
ture for Local Area Networks (LANs). It is
a shared-media network architecture. The
IEEE 802.3 standard details its functional-
ity.
DNS (Domain Name System): System used
to map readable machine names into IP
addresses
Driver: Software that interfaces a computer Ethernet cable: A wire similar to telephone
with a specific hardware device.
cable that carries signals between Ethernet
devices.
DSSS (Direct Sequence Spread Spectrum):
Method of spreading a wireless signal into
wide frequency bandwidth.
File and Print Sharing: A Microsoft applica-
tion that allows computers on a network to
share files and printers.
DTE (Data Terminal Equipment): Device that
controls data flowing to and from a com-
puter.
Firmware: Programming inserted into
programmable read-only memory, thus
becoming a permanent part of a computing
device.
Dynamic IP Address: An IP address that is
automatically assigned to a client station
Download from Www.Somanuals.com. All Manuals Search And Download.
ꢁ1
Glossary
Frame: A fixed block of data, transmitted as Infrastructure: A wireless network or
a single entity. Also referred to as packet.
other small network in which the wireless
network devices are made a part of the
network through the Access Point.
Full-Duplex: To transmit on the same
channel in both directions simultaneously.
ISP (Internet Service Provider): A company
that provides access to the Internet and
other related services.
Gbps (Giga Bits per second): One billion
bits per second.
Half-duplex: To transmit on the same
channel in both directions, one direction at
a time.
IV (Initialization Vector): The header section
of a message packet.
LAN (Local Area Network): A group of com-
puters and peripheral devices connected to
share resources.
Hub: A device which allows connection
of computers and other devices to form a
LAN.
LED (Light Emitting Diode): The lights on a
hardware device representing the activity
through the ports.
IEEE (Institute of Electrical and Electronics
Engineers): The professional organization
which promotes development of electronics
technology.
MAC (Medium Access Control) Address: A
unique number that distinguishes network
cards.
IP (Internet Protocol) Address: A unique
32-binary-digit number that identifies each
sender or receiver of information sent in
packets.
Mbps (Mega Bits Per Second): A measure-
ment of millions of bits per second.
Download from Www.Somanuals.com. All Manuals Search And Download.
ꢁꢀ
Glossary
MDI/X (Media Dependent Interface/Cross-
over): Port on a network hub or switch
that crosses the incoming transmit lines
with the outgoing receive lines.
Packet Filtering: Discarding unwanted
network traffic based on its originating ad-
dress or its type.
PCI (Peripheral Component Interconnect):
A bus that is connected directly to the
CPU.
MHz (MegaHertz): One million cycles per
second.
MIB II: A database containing performance
PCMCIA (Personal Computer Memory Card
information and statistics on each device in International Association) Card: Removable
a network.
module that adds features to a portable
computer.
MIPS (Million Instructions Per Second): A
measurement of processing speed.
Ping (Packet Internet Groper): An Internet
utility used to determine whether a par-
ticular IP address is online.
NAT (Network Address Translation): An in-
ternet standard that enables a LAN to use
one set of IP addresses for internal traffic
and a second set for external traffic.
Plug and Play: Hardware that, once in-
stalled (“plugged in”), can immediately be
used (“played”), as opposed to hardware
that requires manual configuration.
NIC (Network Interface Card): An expan-
sion card connected to a computer so the
computer can be connected to a network.
PoE (Power over Ethernet): A mechanism
to send DC power to a device using a CAT5
Ethernet cable.
Packet: A block of data that is transferred
as a single unit, also called a frame or a
block.
Download from Www.Somanuals.com. All Manuals Search And Download.
ꢁꢁ
Glossary
transmission device.
PPPoE (Point-to-Point Protocol over Ether-
net): A specification for connecting users
on an Ethernet line to the Internet through
a common broadband medium.
ROM (Read Only Memory): Permanent
memory.
Router: Device that can connect individual
LANs and remote sites to a server.
Protocol: A standard way of exchanging
information between computers.
Roaming: The ability to use a wireless de-
vice while moving from one access point to
another without losing the connection.
RADIUS (Remote Authentication Dial In User
Service): A server that issues authentica-
tion key to clients.
Script: A macro or batch file containing
instructions and used by a computer to
perform a task.
RAM (Random Access Memory): Non-per-
manent memory.
Repeater Hub: A device that collects,
strengthens and transmits information to
all connected devices, allowing the network
to be extended to accommodate additional
workstations.
Server: Any computer that makes files or
peripheral devices available to users of the
network and has a resident Network OS.
SMTP (Simple Mail Transfer Protocol): The
protocol used to define and deliver elec-
tronic mail (E-mail) from one location to
another.
RC4: The encryption algorithm that is used
in WEP.
RJ-45 connector: An 8-pin connector used
between a twisted pair cable and a data
SNMP (Simple Network Management Pro-
tocol: An application layer protocol that
outlines the formal structure for communi-
Download from Www.Somanuals.com. All Manuals Search And Download.
ꢁ4
Glossary
cation among network devices.
encryption method replacing WEP. TKIP
uses random IV and frequent key exchang-
es.
Static IP Address: A permanent IP address
is assigned to a node in a TCP/IP network.
Also known as global IP.
Topology: The shape of a LAN (Local Area
Network) or other communications system.
STP (Shielded Twisted Pair): Twisted Pair
cable wrapped in a metal sheath to provide
extra protection from external interfering
signals.
Twisted Pair: Cable that comprises 2 or
more pair of insulated wires twisted to-
gether.
Subnet Mask: An eight-byte address di-
vided into 4 parts separated by periods.
UDP (User Datagram Protocol): A com-
munication method (protocol) that offers a
limited amount of service when messages
are exchanged between computers in a
network. UDP is used as an alternative to
TCP/IP.
TCP/IP (Transmission Control Protocol/Inter-
net Protocol: Protocol used by computers
when communicating across the Internet
or Intranet.
Uplink: Link to the next level up in a com-
munication hierarchy.
TFTP (Trivial File Transfer Protocol): Simple
form of FTP (File Transfer Protocol), which
Uses UDP (User Datagram Protocol), rather
than TCP/IP for data transport and pro-
vides no security features.
UTP (Unshielded Twisted Pair) cable: Two or
more unshielded wires twisted together to
form a cable.
TKIP (Temporal Key Integrity Protocol): An
WAN (Wide Area Network): A networking
Download from Www.Somanuals.com. All Manuals Search And Download.
ꢁ5
system covering a wide geographical area.
WEP (Wired Equivalent Privacy): An en-
cryption method based on 64 or 128-bit
algorithm.
Web Browser: A software program that al-
lows viewing of web pages.
Wi-Fi (Wireless Fidelity): An organization
that tests and assures interoperability
among WLAN devices.
Wire Speed: The maximum speed at which
a given packet can be transferred us-
ing Ethernet and Fast Ethernet standard
specifications.
WLAN (Wireless LAN): A LAN topology using
wireless devices.
VPN (Virtual Private Network): A security
method to connect remote LAN users to a
corporate LAN system.
Download from Www.Somanuals.com. All Manuals Search And Download.
ꢁꢂ
FCC / CE Information
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: To assure continued compliance, (example - use only shielded interface cables
when connecting to computer or peripheral devices). Any changes or modifications not
expressly approved by the party responsible for compliance could void the user’s authority
to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
Download from Www.Somanuals.com. All Manuals Search And Download.
ꢁꢃ
FCC / CE Information
IMPORTANT NOTE:
FCC RF Radiation Exposure Statement:
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with a minimum distance
of 20 centimeters between the radiator and your body.
This transmitter must not be co-located or operating in conjunction with any other antenna
or transmitter.
R&TTE Compliance Statement
This equipment complies with all the requirements of the DIRECTIVE 1999/5/EC OF THE
EUROPEAN PARLIAMENT AND THE COUNCIL of 9 March 1999 on radio equipment and
telecommunication terminal Equipment and the mutual recognition of their conformity
(R&TTE). The R&TTE Directive repeals and replaces in the directive 98/13/EEC
(Telecommunications Terminal Equipment and Satellite Earth Station Equipment) As of
April 8, 2000.
Safety
This equipment is designed with the utmost care for the safety of those who install and
use it. However, special attention must be paid to the dangers of electric shock and static
Download from Www.Somanuals.com. All Manuals Search And Download.
ꢁꢄ
FCC / CE Information
electricity when working with electrical equipment. All guidelines of this manual and of
the computer manufacturer must therefore be allowed at all times to ensure the safe use
of the equipment.
EU Countries intended for use
The ETSI version of this device is intended for home and office use in Austria, Belgium,
Denmark, Finland, France (with Frequency channel restrictions), Germany, Greece,
Iceland, Ireland, Italy, Luxembourg, Norway, The Netherlands, Portugal, Spain, Sweden,
Switzerland and United Kingdom.
The ETSI version of this device is also authorized for use in EFTA member states Iceland,
Liechtenstein, Norway and Switzerland.
EU Countries Not intended for use
None.
Potential restrictive use
France: Only channels 10,11,12, and 13.
Download from Www.Somanuals.com. All Manuals Search And Download.
ꢁꢅ
Warranty Information
Buffalo Technology (USA), Inc. products comes with a two-year limited warranty from the
date of purchase. Buffalo Technology (USA), Inc. warrants to the original purchaser the
product; good operating condition for the warranty period. This warranty does not include
non-Buffalo Technology (USA), Inc. installed components. If the Buffalo product malfunctions
during the warranty period, Buffalo Technology (USA) Inc. will, replace the unit, provided
the unit has not been subjected to misuse, abuse, or non-Buffalo Technology (USA), Inc.
authorized alteration, modifications or repair.
All expressed and implied warranties for the Buffalo Technology (USA) Inc. product line
including, but not limited to, the warranties of merchantability and fitness of a particular
purpose are limited in duration to the above period.
Under no circumstances shall Buffalo Technology (USA), Inc. be liable in any way to the
user for damages, including any lost profits, lost savings or other incidental or consequential
damages arising out of the use of, or inability to use the Buffalo products.
In no event shall Buffalo Technology (USA), Inc. liability exceed the price paid for the prod-
uct from direct, indirect, special, incidental, or consequential damages resulting from the
use of the product, its accompanying software, or its documentation. Buffalo Technology
(USA), Inc. does not offer refunds for any product.
Download from Www.Somanuals.com. All Manuals Search And Download.
40
Technical Support
Buffalo Technology offers toll-free technical support 24 hours a day, 7 days a week for this product.
Customers in the United States and Canada can obtain technical support using the following
information:
Web:
E-mail:
Telephone:
1(ꢄꢂꢂ)-ꢃ5ꢀ-ꢂꢀ10 (USA & Canada only)
FCC Warning
Thisdevicecomplieswithpart15oftheFCCRules. Operationissubjecttothefollowingtwoconditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
GPL Statement
ThisproductusesGPL/LGPLsoftware. PleaseseetheGNULICENSEdocumentontheLinkNavigator
CD-ROM for more information concerning the terms of the license. To obtain a copy of our open
source software, please send a message to [email protected] to inquire about obtaining a pack-
age.
Download from Www.Somanuals.com. All Manuals Search And Download.
41
|