December 2009
LBPD01A-KIT
VDSL2 PoE Ethernet Extender Kit, PD
Extend Ethernet with 100-/60-Mbps downstream/
upstream connections over copper.
Kit includes two extenders—one with standard power and one that’s a PoE
powered device (PD).
Bridges 10BASE-T/100BASE-TX Ethernet interface.
Supports DSL connection up to 4000 feet (1219 m).
Select from Fast and Interleaved modes.
Provides low latency for video/voice/data applications.
IEEE 802.3af PoE compliant.
Order toll-free in the U.S.: Call 877-877-BBOX (outside U.S. call 724-746-5500) •
FREE technical support 24 hours a day, 7 days a week: Call 724-746-5500 or fax 724-746-0746 •
Mailing address: Black Box Corporation, 1000 Park Drive, Lawrence, PA 15055-1018 •
Customer
Support
Information
Download from Www.Somanuals.com. All Manuals Search And Download.
FCC and IC RFI Statements
Federal Communications Commission and Industry Canada Radio Frequency Interference
Statements
This equipment generates, uses, and can radiate radio-frequency energy, and if not installed and used properly, that is, in strict
accordance with the manufacturer’s instructions, may cause interference to radio communication. It has been tested and found to
comply with the limits for a Class A computing device in accordance with the specifications in Subpart J of Part 15 of FCC rules,
which are designed to provide reasonable protection against such interference when the equipment is operated in a commercial
environment. Operation of this equipment in a residential area is likely to cause interference, in which case the user at his own
expense will be required to take whatever measures may be necessary to correct the interference.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to
operate the equipment.
This digital apparatus does not exceed the Class A limits for radio noise emission from digital apparatus set out in the Radio
Interference Regulation of Industry Canada.
Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites applicables aux appareils numériques de
la classe A prescrites dans le Règlement sur le brouillage radioélectrique publié par Industrie Canada.
Page 3
Download from Www.Somanuals.com. All Manuals Search And Download.
VDSL2 PoE Ethernet Extender Kit, PD
Normas Oficiales Mexicanas (NOM) Electrical Safety Statement
INSTRUCCIONES DE SEGURIDAD
1. Todas las instrucciones de seguridad y operación deberán ser leídas antes de que el aparato eléctrico sea operado.
2. Las instrucciones de seguridad y operación deberán ser guardadas para referencia futura.
3. Todas las advertencias en el aparato eléctrico y en sus instrucciones de operación deben ser respetadas.
4. Todas las instrucciones de operación y uso deben ser seguidas.
5. El aparato eléctrico no deberá ser usado cerca del agua—por ejemplo, cerca de la tina de baño, lavabo, sótano mojado o cerca
de una alberca, etc..
6. El aparato eléctrico debe ser usado únicamente con carritos o pedestales que sean recomendados por el fabricante.
7. El aparato eléctrico debe ser montado a la pared o al techo sólo como sea recomendado por el fabricante.
8. Servicio—El usuario no debe intentar dar servicio al equipo eléctrico más allá a lo descrito en las instrucciones de operación.
Todo otro servicio deberá ser referido a personal de servicio calificado.
9. El aparato eléctrico debe ser situado de tal manera que su posición no interfiera su uso. La colocación del aparato eléctrico
sobre una cama, sofá, alfombra o superficie similar puede bloquea la ventilación, no se debe colocar en libreros o gabinetes
que impidan el flujo de aire por los orificios de ventilación.
10. El equipo eléctrico deber ser situado fuera del alcance de fuentes de calor como radiadores, registros de calor, estufas u otros
aparatos (incluyendo amplificadores) que producen calor.
11. El aparato eléctrico deberá ser connectado a una fuente de poder sólo del tipo descrito en el instructivo de operación, o como
se indique en el aparato.
12. Precaución debe ser tomada de tal manera que la tierra fisica y la polarización del equipo no sea eliminada.
13. Los cables de la fuente de poder deben ser guiados de tal manera que no sean pisados ni pellizcados por objetos colocados
sobre o contra ellos, poniendo particular atención a los contactos y receptáculos donde salen del aparato.
14. El equipo eléctrico debe ser limpiado únicamente de acuerdo a las recomendaciones del fabricante.
15. En caso de existir, una antena externa deberá ser localizada lejos de las lineas de energia.
16. El cable de corriente deberá ser desconectado del cuando el equipo no sea usado por un largo periodo de tiempo.
17. Cuidado debe ser tomado de tal manera que objectos liquidos no sean derramados sobre la cubierta u orificios de ventilación.
18. Servicio por personal calificado deberá ser provisto cuando:
A: El cable de poder o el contacto ha sido dañado; u
B: Objectos han caído o líquido ha sido derramado dentro del aparato; o
C: El aparato ha sido expuesto a la lluvia; o
D: El aparato parece no operar normalmente o muestra un cambio en su desempeño; o
E: El aparato ha sido tirado o su cubierta ha sido dañada.
724-746-5500 | blackbox.com
Page 4
Download from Www.Somanuals.com. All Manuals Search And Download.
CE Statement
European Community (CE) Electromagnetic Compatibility Directive
This equipment has been tested and found to comply with the protection requirements of European Emission Standard
EN55022/EN61000-3 and the Generic European Immunity Standard EN55024.
EMC:
EN55022(2003)/CISPR-2(2002): Class A
IEC61000-4-2 (2001): 4 KV CD, 8 KV AD
IEC61000-4-3(2002): 3 V/m
IEC61000-4-4(2001): 1 KV (power line), 0.5 KV (signal line)
Page 5
Download from Www.Somanuals.com. All Manuals Search And Download.
VDSL2 PoE Ethernet Extender Kit, PD
1. Specifications .......................................................................................................................................................................................... 7
2. Overview................................................................................................................................................................................................. 8
2.1 Introduction ...................................................................................................................................................................................... 8
2.2 Features............................................................................................................................................................................................ 8
2.3 Application ....................................................................................................................................................................................... 8
2.4 What’s Included................................................................................................................................................................................ 9
2.5 LED Descriptions ............................................................................................................................................................................... 9
2.6 Front and Back Panels ......................................................................................................................................................................10
3. Installation .............................................................................................................................................................................................11
4. DIP Switches ..........................................................................................................................................................................................12
724-746-5500 | blackbox.com
Page 6
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1: Specifications
1. Specifications
Data Rate (Maximum): 100/60 Mbps
Transmission Distance (Maximum): 4000 ft. (1219 m)
Flow Control: Half-/full-duplex
MDI-X: Automatic
Standards: ITU-T G.993.1/2, SG15Q4 DMT compliant, trellis code with 1024 DMT bins, EMI emissions compliant, FCC Class A,
CE, IEEE 802.3/IEEE 802.3u Ethernet, 10BASE-/100BASE-TX, IEEE 802.3af PoE
PoE Power Reception Supports: Endpoint: Via twisted-pair: Pins 1, 2, 3, 6;
Midspan: Via twisted-pair: Pins 4, 5, 7, 8
Connectors: PD: (1) RJ-11, (1) RJ-45;
Standard: (1) RJ-11, (2) RJ-45
Indicators: PD: (4) LEDs: Power, LAN, DSL, M/S;
Standard: (5) LEDs: Power, LAN1, LAN2, DSL, M/S
Power Input: PD: 100mA @ -48 VDC from IEEE 802.3af PSE or PoE injector;
Standard: 5 VDC, 1 amp
Temperature Tolerance: Operating: 32 to 122° F (0 to 50° C)
Humidity Tolerance: 5 to 95% noncondensing
Size: 0.8"H x 4.7"W x 3.5"D (2 x 12 x 9 cm)
Page 7
Download from Www.Somanuals.com. All Manuals Search And Download.
VDSL2 PoE Ethernet Extender Kit, PD
2. Overview
2.1 Introduction
The LBPD01A-KIT is a VDSL LAN Extender that provides broadband transmission rates up to 100-/60-Mbps for downstream/
upstream over single-pair copper line for point-to-point Ethernet connectivity. The kit includes two extenders—one with standard
power and one that’s a PoE powered device (PD). The PD extender draws its power from a Power over Ethernet (PoE) switch,
so you can easily integrate it into a PoE infrastructure without using another power outlet. The LBPD01A-KIT is ideal for high-
bandwidth applications such as LAN-to-LAN, video streaming, FTTB, and MDU/MTU over single twisted-pair telephone lines.
At 100-/60-Mbps downstream/upstream, the LBPD01A-KIT supports transmission distances up to 500 feet (152.4 meters) and at
28-/0.3-Mbps it supports distances up to 4000 feet (1219 m). Using its Power over Ethernet (PoE) feature, the VDSL2 PoE
Ethernet Extender (PD) derives power over the Ethernet cable from power sourcing equipment (PSE), such as a PoE Ethernet
Switch, so it may work without an external power adapter.
Installation is plug-and-play. You can configure each LBPD01A-KIT as either master for central side (CO) or slave for remote side
(RT) by using the DIP switch settings. The LBPD01A-KIT conforms to the ITU-T G.993.1 and G.993.2 to meet VDSL/VDSL2 and
SG15Q4 DMT for network requirements.
2.2 Features
• ITU-T G.993.1, G.993.2, VDSL/VDSL2, and SG15Q4 DMT compliant
• 100-/60-Mbps downstream/upstream for up to 500 feet (152.4 m)
• Supports DSL connection up to 4000 feet (1219 m) at 28/0.3 Mbps
• Trellis coding support for up to 1024 Discrete Multi-Tone (DMT) bin
• Selectable Fast and Interleaved modes
• Selectable fixed data rate and fixed SNR margin
• Auto MDI-X for 10BASE-T/100BASE-TX Ethernet LAN Port, so you don’t need a crossover cable on the Ethernet side
• IEEE 802.3af PoE compliant
• 4 DIP switches for master/slave configuration
• Low latency for video/voice/data applications
2.3 Application
VDSL2 PoE
Ethernet Extender
(PD), Standard Unit
VDSL2 PoE
Ethernet Extender
(PD), PD Unit
PoE PSE Switch
or PSE Device
Max. 4000 ft.
(1219 m)
for DSL Line
LAN 1
PC
LAN 2
LAN, Power
IP Camera
Figure 2-1. Typical application.
724-746-5500 | blackbox.com
Page 8
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2: Overview
2.4 What’s Included
Your package should include the following items. If anything is missing or damaged,
please contact Black Box Technical Support at 724-746-5500.
• (1) VDSL2 PoE Ethernet Extender (PD)
• (1) VDSL2 PoE Ethernet Extender (Standard)
• (1) 5-VDC, 1-A power adapter for VDSL2 PoE Ethernet Extender (Standard)
• This user’s manual on CD-ROM
2.5 LED Descriptions
Table 2-1. LED indicators.
LED
Color
Green
Green
Green
Function
POWER
DSL
Lights when power is on.
Lights when VDSL is connected.
M/S
Lights when the device is in slave mode.
Off when device is in master mode.
LAN
Green
Lights when Ethernet connection is made.
Blinks when transmitting/receiving data.
Page 9
Download from Www.Somanuals.com. All Manuals Search And Download.
VDSL2 PoE Ethernet Extender Kit, PD
2.6 Front and Back Panels
Figures 2-2 through 2-5 show the extenders’ front and rear panels.
DIP Switches
LED Indicators
Figure 2-2. Front panel, VDSL2 PoE Ethernet Extender (PD), PD unit.
RJ-45 Connector
RJ-11 Connector
Figure 2-3. Rear panel, VDSL2 PoE Ethernet Extender (PD), PD unit.
DIP Switches
LED Indicators
Figure 2-4. Front panel, VDSL2 PoE Ethernet Extender (PD), Standard unit.
Power Input
RJ-11 Connector
RJ-45 Connectors
Figure 2-5. Rear panel, VDSL2 PoE Ethernet Extender (PD), Standard unit.
724-746-5500 | blackbox.com
Page 10
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3: Installation
3. Installation
Because the VDSL2 PoE Ethernet Extenders are preconfigured for basic applications, you can install them quickly. Follow these
steps:
1. Connect the line interface between the units with RJ-11 cable.
2. Connect the Standard Extender to a twisted-pair Ethernet connection. Connect the PD Extender to a PoE PSE switch or
other PSE device using copper twisted-pair cable.
NOTE: Make sure that the PSE device is turned on, or the VDSL2 PoE Ethernet Extender (PD) will not work.
3. Connect the power adapter to the Standard extender and plug it in.
NOTE: The interconnecting cables should be rated for external use and appropriate for the application’s voltage, current,
anticipated temperature, flammability, and mechanical serviceability.
Table 3-1 shows the data rate and transmission distance information via 26 AWG at 6 dB.
Table 3-1. Supported data rates and transmission distances.
Downstream
Upstream
Distance
Data Rate (Mbps)
Data Rate (Mbps) (feet)
100
98
90
80
70
60
48
39
35
28
60
53
44
36
27
18
11
8
500
1000
1250
1500
1750
2000
2500
3000
3500
4000
3.5
0.3
NOTE: Depending on your application, you might need to change the DIP switches for optimum performance.
Page 11
Download from Www.Somanuals.com. All Manuals Search And Download.
VDSL2 PoE Ethernet Extender Kit, PD
4. DIP Switches
Table 4-1 describes the DIP Switches. Select the switches for optimal configuration.
Table 4-1. DIP switches and their functions.
DIP Switches
SW-1
SW-2
SW-3
SW-4
Definition
Master/Slave
Impulse Noise
Data Rate
SNR
Protection Mode
Off
On
Master
Slave
Interleaved
Fast
50/20 Mbps
Full Rate
9 dB
6 dB
Standard extender
PD extender
Figure 4-1. DIP switches’ default settings.
Table 4-2. DIP switches’ descriptions.
SW-1: CO/Remote
Off: VDSL2 PoE Ethernet Extender will act as the master side.
On: VDSL2 PoE Ethernet Extender will act as the slave side.
SW-2: Mode for impulse noise protection
Off: Interleaved mode provides impulse noise protection for any impulse noise with a duration less than 250 µs.
Interleaved mode has a maximum end-to-end latency of 10 ms. Interleaved mode is the default mode.
On: Fast mode guarantees a minimum end-to-end latency less than 1 ms.
SW-3: Rate limit control
Off: Line rate limited to 50/20 Mbps.
On: Provides up to 100-/60-Mbps line rate at distances up to 500 feet (152.4 m).
SW-4: Signal-to-noise ratio (SNR)
Off: Higher SNR margin (9 dB) will result in fewer errors with a more stable VDSL link.
On: Original and normal channel noise protection with 6 dB SNR.
724-746-5500 | blackbox.com
Page 12
Download from Www.Somanuals.com. All Manuals Search And Download.
Black Box Tech Support: FREE! Live. 24/7.
Tech support the
way it should be.
Great tech support is just 20 seconds away at 724-746-5500 or blackbox.com.
About Black Box
Black Box Network Services is your source for more than 118,000 networking and infrastructure products. You’ll find everything
from cabinets and racks and power and surge protection products to media converters and Ethernet switches all supported by
free, live 24/7 Tech support available in 20 seconds or less.
© Copyright 2009. All rights reserved.
724-746-5500 | blackbox.com
Download from Www.Somanuals.com. All Manuals Search And Download.
|