Black Box Network Hardware FlexPoint T1 E1 converter User Manual

Local loop-back (L/LB)  
This switch will set the FlexPoint T1/E1 converter in  
loop-back mode on both the fiber and copper connections.  
By returning the switch to the normal position the unit will  
resume to normal operation.  
Description:  
320 appliance cable with a minimum rating of 10 AMPs.  
Note: Use copper cables that are compliant with the  
specifications that are outlined in copper cable  
specifications.  
Coax E1 Connector  
Attach the BNC to the FlexPoint T1/E1 converter and  
attach the other end of the BNC to the network equipment.  
Note: Use copper cables that are compliant with the  
specifications that are outlined in copper cable  
specifications.  
Line Type Port Type Distances  
Switch Positions  
a
5. User-supplied cables must meet the required safety  
agency approvals, applicable international standards  
and electrical ratings for the region.  
1
2
3
4
The FlexPoint T1/E1 connects T1 and E1 devices, such as  
PBXs, CSUs and routers, via multimode (MM) or single-mode  
(SM) fiber. Designed to extend the standardT1/E1 twisted pair  
or Coax network distances over fiber, this converter provides  
protection from environmental noise and effectively increases  
high-speed network reliability. The following models are  
described here.  
T1 DSX-1  
T1 DSX-1  
T1 DSX-1  
T1 DSX-1  
T1 DSX-1  
RJ-45/48 0’ - 133’  
RJ-45/48 133’ - 266’  
RJ-45/48 266’ - 399’  
RJ-45/48 399’ - 533’  
RJ-45/48 533’ - 655’  
B B B B  
B B B A  
B B A B  
B B A A  
B A B B  
WARNING!  
Cu-Rx  
FO-Tx  
Before inserting the Power Adapter, verify that the  
power on the unit is appropriate for your AC line  
voltage source.  
US Power Supply  
International Power Supply  
Model #  
Fiber Type  
Max Distance  
5km / 3.1mi  
28km / 16.8mi  
5km / 3.1mi  
28km / 16.8mi  
58km / 36 mi  
5km / 3.1mi  
28km / 16.8mi  
5km / 3.1mi  
MT660A-MM  
MT661A-SM  
MT660A-MM-E  
MT661A-SM-E  
T1 DS-1  
T1 DS-1  
T1 DS-1  
T1 DS-1  
RJ-45/48 0 dB  
B B B B  
B A B A  
B A A B  
B A A A  
MT660A-MM  
MT661A-SM  
MT662A-MSC  
MT663A-SSC  
MT664A-SSC  
MT660A-MM-E  
MT661A-SM-E  
MT662AE-MSC MM, SC, 1300nm  
MT663AE-SSC  
MT664AE-SSC  
MM, ST, 1300nm  
SM, ST, 1300nm  
MM, SC, 1300nm  
SM, SC, 1300nm  
SM, SC, 1300nm  
MM, ST, 1300nm  
SM, ST, 1300nm  
Switch Settings:  
UTP DCE/DTE setting  
The UTP DCE/DTE switch is used to eliminate the need for  
crossoverandcustomcablestoconnectdevicestogetherwhen  
using the RJ-45/48 port. Set this switch to DCE to use a  
straight-through cable and to DTE when a crossover-cable  
would be required.  
Mounting instructions:  
Cu-Tx  
FO-Rx  
RJ-45/48 -7.5 dB  
RJ-45/48 -15.0 dB  
RJ-45/48 -22.5 dB  
The FlexPoint Fiber Converter can be solo-mounted using  
a wall-mounting kit, or rack-mounted using a 5-unit shelf,  
or a high-density FlexPoint 14-Unit Power-Redundant  
Chassis.  
Loopback Enabled  
MT662A-MSC  
MT663A-SSC  
MT662AE-MSC  
MT663AE-SSC  
Remote loop-back (R+L/LB)  
This switch will allow the entire fiber segment to be tested  
at either of the FlexPoint T1/E1 converters without having  
to set switches on both units. When set in this mode of  
operation the local unit is switched in a local loop-back  
mode. And in addition to the local loop-back mode of  
operation the fiber Tx port will be further encoded to carry  
a remote loop-back protocol. This remote loop-back  
protocol will set the far end FlexPoint T1/E1 converter to  
remote loop-back mode of operation and return a signal to  
the sending unit.An LED on the local and remote FlexPoint  
T1/E1 converters will show a confirmation that the fiber  
segment is communicating properly between devices. By  
returning the switch to the normal position it will resume  
to normal operation.  
MT664A-SSC  
MT664AE-SSC  
E1 75 Ω  
E1 120 Ω  
E1 75 Ω  
E1 120 Ω  
Coax/BNC Standard  
RJ-45/48 Standard  
Coax/BNC Extended  
RJ-45/48 Extended  
A B B B  
A B B A  
A B A B  
A B A A  
Fiber Optic Cable Attachment:  
Connect the fiber cables between the FlexPoint T1/E1  
converters. The transmit (Tx) must attach to the receive  
side and the receive (Rx) must attach to the transmit side.  
Note: Use fiber cables that are compliant with the  
specifications that are outlined in fiber cable specifications.  
SM, SC, 1300nm  
SM, SC, 1300nm  
28km / 16.8mi  
58km / 36 mi  
DCE  
DTE  
FlexPointT1/E1 Copper to Fiber  
Line Driver  
Power Adapter Notice  
Operational switch settings and functions  
Twisted  
Pair #1  
RTIP  
TTIP  
Twisted  
Pair #1  
RTIP  
TTIP  
1
2
1
2
1. When Using in a stand-alone configuration, this product  
is intended to be and must be used only with a Listed  
Direct Plug-In Power Unit marked “Class 2” and rated  
at 9VDC, 1 Amp.  
2. This product should always be used only with the supplied  
power unit .  
3. Models shipped with international power supplies are  
capable of auto switching from 100-230V, and are  
supplied with a U.S. type NEMA 5-15 power cable.  
4. For products being shipped outside of the U.S., the  
user is required to install a properly grounded IEC  
RRING  
TRING  
The following operational switches located on the front of  
the FlexPoint T1/E1 converter are to assist in installation  
and fault isolation.  
RRING  
TRING  
Copper Cable Attachment:  
RJ-45/RJ-48 T1/E1 connector  
Twisted  
Pair #2  
4
5
TTIP  
RTIP  
Twisted  
Pair #2  
4
5
TTIP  
RTIP  
TRING  
RRING  
TRING  
RRING  
Connect to the RJ-45/48 connector on the FlexPoint T1/  
E1 converter via a category 3 or better cable (Category 5  
is recomended) and attach the other end to the network  
equipment. (The twisted pair connection requires two active  
pairs in a T1/E1 environment. The active pairs are pins  
1&2 and pins 4&5. Only dedicated wire pairs should be  
used for the active pins.) Set the UTP DCE / DTE switch  
for the RJ-45/48 port to the appropriate setting.  
Order toll-free in the U.S.: Call 877-877-BBOX  
(outside U.S. call 724-746-5500)  
CUSTOMER  
SUPPORT  
INFORMATION  
Local Dual Loop Back  
T1/E1 Copper line configuration settings  
Cu-Rx  
FO-Tx  
FO-Rx  
Cu-Tx  
FREE technical support 24 hours a day, 7 days a  
week; Call 724-746-5500 or fax 724-746-0746  
Remote & Local Loop Back  
The T1/E1 copper line codes and line lengths are configured  
using dip switches located on the side of the FlexPoint T1/E1  
media converter.  
Normal  
Force 1’s to Fiber  
Mailing address: Black Box Corporation,  
1000 Park Drive, Lawrence, PA 15055-1018  
Force 1’s Copper  
Cu-Tx  
FO-Rx  
FO-Tx  
Cu-Rx  
Remote Loop Request  
Over Fiber  
Page 1  
Page 2  
Page 3  
Page 4  
Page 5  
Page 6  
Local loop-back and Remote loop-back  
Operational rating on relay pins 3 & 6: 0-220VDC max 2A  
Wavelength:  
Max Distance:  
1300nm  
58km / 36mi  
TRADEMARKS  
NORMAS OFICIALES MEXICANAS (NOM)  
ELECTRICAL SAFETY STATEMENT  
1. Todas las instrucciones de seguridad y operación deberán ser  
leídas antes de que el aparato eléctrico sea operado.  
2. Las instrucciones de seguridad y operación deberán ser  
guardadas para referencia futura.  
3. Todas las advertencias en el aparato eléctrico y en sus  
instrucciones de operación deben ser respetadas.  
4. Todas las instrucciones de operación y uso deben ser seguidas.  
5. El aparato eléctrico no deberá ser usado cerca del agua—por  
ejemplo, cerca de la tina de baño, lavabo, sótano mojado o  
cerca de una alberca, etc.  
6. El aparato eléctrico debe ser usado únicamente con carritos o  
pedelstales que sean recomendados por el fabricante.  
7. El aparato eléctrico debe ser montado a la pared o al techo sólo  
como sea recomendado por el fabricante.  
8. Servicio—El usuario no debe intentar dar servicio al equipo  
eléctrico más allá a lo descrito en las instrucciones de  
operación. Todo otro servicio deberá ser referido a personal de  
servicio calificado.  
9. El aparato eléctrico debe ser situado de tal manera que su  
posición no interfiera su uso. La colocación del aparato  
eléctrico sobre una cama, sofá, alfombra or superficie similar  
puede bloquea la ventilación, no se debe colocar en libreros o  
gabinetes que impidan el flujo de aire por los orificios de  
ventilación.  
10. El equipo eléctrico deber ser situado fuera del alcance de  
fuentes de calor como radiadores, registros de calor, estufas u  
ostros aparatos (incluyendo amplificadores) que producen  
calor.  
11. El aparato eléctrico deberá ser connectado a una fuente de  
poder sólo del tipo descrito en el instructivo de operación, o  
como se indique en el aparato.  
12. Precación debe ser tomada de tal manera que la tierra fisica y  
la polarización del equipo no sea eliminada.  
When both Local and Remote Loop-back are set to the  
Normal position, the FlexPoint T1/E1 uses the default B8ZS  
data format. When both switches are turned to their On  
position, it uses the AMI data format.  
All applied-for and registered trademarks are the property of their  
respective owners.  
LED Indicators  
13. Los cables de la fuente de poder deben ser guiados de tal  
manera que no sean pisados ni pellizcados por objetos  
colocados sobre o contra ellos, poniendo particular atención a  
los contactos y receptáculos donde salen del aparato.  
14. El equipo eléctrico debe ser limpiado únicamente de acuerdo a  
las recomendaciones del fabricante.  
Copper Cable Specifications:  
Twisted-Pair cable for T1  
Gauge  
Impedance  
Impedance characteristic  
Maximum distance  
Twisted-Pair cable for E1  
Gauge  
LED  
Color  
Status  
Description  
Power:  
FEDERAL COMMUNICATIONS COMMISSION AND  
CANADIAN DEPARTMENT OF COMMUNICATIONS  
RADIO FREQUENCY INTERFERENCE STATEMENTS  
Transmit/force 1’s to fiber  
Yellow On  
Power applied  
22 to 24 AWG  
100 Ω + 10%  
2.6 dB / 100m @ 1.0 MHz  
6,000 ft  
Fiber:  
This switch is used to insert an “all ones” pattern into the  
data stream being transmitted out of the fiber port on the  
FlexPoint T1/E1 converter. Data being received on the coax  
or twisted pair will be disabled and data being received on  
the fiber is passed through to the coax or twisted pair side.  
By returning the switch to the normal position the unit will  
resume to normal operation.  
Green Off  
On  
No signal detect  
Signal detect  
This equipment generates, uses, and can radiate radio frequency  
energy and if not installed and used properly, that is, in strict  
accordance with the manufacturer’s instructions, may cause  
interference to radio communication. It has been tested and found  
to comply with the limits for a Class A computing device in  
accordance with the specifications in subpart J of Part 15 of FCC  
rules, which are designed to provide reasonable protection against  
such interference when the equipment is operated in a commercial  
environment. Operation of this equipment in a residential area is  
likely to be cause interference, in which case the user at his own  
expense will be required to take whatever measures may be  
necessary to correct the interference.  
15. En caso de existir, una antena externa deberá ser localizada  
lejos de las lineas de energia.  
Blink  
All ones received  
16. El cable de corriente deberá ser desconectado del cuando el  
equipo no sea usado por un largo periodo de tiempo.  
17. Cuidado debe ser tomado de tal manera que objectos liquidos  
no sean derramados sobre la cubierta u orificios de ventilación.  
18. Servicio por personal calificado deberá ser provisto cuando:  
A: El cable de poder o el contacto ha sido dañado; u  
B: Objectos han caído o líquido ha sido derramado dentro del  
aparato; o  
UTP/Coax:  
Green Off  
No signal detect  
Signal detect  
22 to 24 AWG  
120 Ω + 10%  
2.6 dB / 100m @ 1.0 MHz  
8,000 ft  
On  
Impedance  
Blink  
All ones received  
Transmit/force 1’s to Coax or UTP  
Impedance characteristic  
Maximum distance  
Coax cable for E1  
Gauge  
Impedance  
Impedance characteristic  
Maximum distance  
Test:  
This switch is used to insert an “all ones” pattern into the  
data stream being transmitted out of the coax or twisted  
pair on the FlexPoint T1/E1 converter. Data being received  
on the fiber will be disabled and data being received on  
the coax or twisted pair is passed through to the fiber side.  
By returning the switch to the normal position the unit will  
resume to normal operation.  
Yellow Off  
Normal operation  
On  
Blink  
L/LB or All 1’s Test mode  
R+L/LB Received master  
22 to 24 AWG  
75 Ω + 10%  
2 dB / 100m @ 1.0 MHz  
8,000 ft  
C: El aparato ha sido expuesto a la lluvia; o  
D: El aparato parece no operar normalmente o muestra un  
cambio en su desempeño; o  
Fast Blink R+L/LB Received slave  
Changes or modifications not expressly approved by the party  
responsible for compliance could void the user’s authority to  
operate the equipment.  
Fiber Cable Specifications:  
Multimode  
E: El aparto ha sido tirado o su cubierta ha sido dañada.  
Alarm Relay Contacts  
Cable:  
50/125, 62.5/125, 100/140 μm  
This digital apparatus does not exceed the Class A limits for radio  
noise emission from digital apparatus set out in the Radio  
Interference Regulation of the Canadian Department of  
Communications.  
The FlexPoint T1/E1 converter also features dry relay  
contacts for optionally connecting the media converter into  
a separate T1/E1 alarm circuit. The relay closes when a  
loss of power or when signal detect is lost to the copper or  
fiber connection.  
Wavelength:  
Max Distance:  
1300nm  
5km / 3.1mi  
Le présent appareil numérique n’émet pas de bruits  
radioélectriques dépassant les limites applicables aux appareils  
numéirques de las classe A prescrites dans le Règlement sur le  
brouillage radioélectrique publié par le ministère des  
Communications du Canada.  
Single-mode  
Cable:  
Relay  
RJ-45/RJ-48  
9/125 μm  
3
Wavelength:  
Max Distance:  
Single-mode long-haul  
Cable:  
1300nm  
28km / 16.8mi  
1000 Park Drive z Lawrence, PA 15055-1018  
724-746-5500 z Fax 724-746-0746  
6
9/125 μm  
040-01021-001E 3/06  
Page 9  
Page 7  
Page 8  
Page 11  
Page 12  
Page 10  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Belkin Portable Speaker F5U228 User Manual
Black Box Network Router PS540A User Manual
Braun Mobility Aid 32899 Rev A User Manual
Brother All in One Printer MFC J6710DW User Manual
Brother Printer QL 500W User Manual
Canon Camcorder CR 1 MARK II User Manual
Canon Indoor Furnishings RS CL07 User Manual
Carrier Air Conditioner 50ZH024 060 User Manual
Casio Digital Camera EX S1 EX M1 User Manual
Chauvet Projector Accessories Projector Accessories User Manual