ProHeat®
U S E R ’ S G U I D E
1699, 7901, 8910 SERIES
3
4-5
6
Safety Instructions
Product View / Accessories
Assembly
7-16
Features / Operations
16-18
Troubleshooting / User Maintenance
18
19
20
Consumer Services
Replacement Parts
Warranty
ug310-5868_1699_306.indd
1
3/1/06 3:13:29 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY INSTRUCTIONS
■
■
■
■
■
■
When using an electrical appliance, basic precautions
should be observed, including the following:
Keep appliance on a level surface.
Turn off all controls before unplugging.
Read all instructions before using your PROHEAT®
®
Unplug before attaching the TurboBrush.
Be extra careful when cleaning stairs.
Close attention is necessary when used by or near children.
WARNING: The Power Cord on this product contains
lead, a chemical known to the State of California to
cause birth defects or other reproductive harm.
Wash hand after handling.
WARNING:
To reduce the risk
of fire, electric shock, or injury:
■
■
■
■
■
Do not immerse.
Use only on surfaces moistened by cleaning process.
Always connect to a properly grounded outlet.
See Grounding Instructions.
SAVE THESE
INSTRUCTIONS.
GROUNDING INSTRUCTIONS
This appliance must be connected to a grounded
wiring system. If it should malfunction or break
down, grounding provides a safe path of least
resistance for electrical current, reducing the risk of
electrical shock. The cord for this appliance has an
equipment-grounding conductor and a grounding
plug. It must only be plugged into an outlet that is
properly installed and grounded in accordance with
all local codes and ordinances.
Unplug from outlet when not in use and before
conducting maintenance or troubleshooting.
Do not leave machine when it is plugged in.
Do not service machine when it is plugged in.
Do not use with damaged cord or plug.
If appliance is not working as it should, has been
dropped, damaged, left outdoors, or dropped into
water, have it repaired at an authorized Service Center.
Use indoors only.
Do not pull or carry by cord, use cord as a handle,
close door on cord, pull cord around sharp corners
or edges, run appliance over cord, or expose cord
to heated surfaces.
■
■
■
■
■
■
■
■
Do not carry the appliance while in use.
Do not unplug by pulling on cord. Unplug by grasping
the plug, not the cord.
Grounded
Outlets
■
■
Do not handle plug or appliance with wet hands.
Do not put any object into appliance openings, use with
blocked opening, or restrict air flow.
■
Do not expose hair, loose clothing, fingers or body
parts to openings or moving parts.
Grounding Pin
■
■
Do not pick up hot or burning objects.
Do not pick up flammable or combustible materials
(lighter fluid, gasoline, kerosene, etc.) or use in the
presence of explosive liquids or vapor.
Do not use appliance in an enclosed space filled with vapors
given off by oil base paint, paint thinner, some moth proofing
substances, flammable dust, or other explosive or toxic vapors.
Do not pick up toxic material (chlorine bleach, ammonia,
drain cleaner, gasoline, etc.).
Do not modify the 3-prong grounded plug.
Do not allow to be used as a toy.
Do not use for any purpose other than described in
this User’s Guide.
Do not operate the appliance unless the belt door is
securely assembled in the location provided.
Use only manufacturer’s recommended attachments.
Use only cleaning products formulated by BISSELL for
use in this appliance to prevent internal component
damage. See the cleaning fluid section of this guide.
Keep openings free of dust, lint, hair, etc.
Do not point attachment nozzle at people or animals
WARNING:
Improper
connection of the equipment-grounding
conductor can result in a risk of
■
■
electrical shock. Check with a qualified
electrician or service person if you aren’t
sure if the outlet is properly grounded.
DO NOT MODIFY THE PLUG. If it will not fit
the outlet, have a proper outlet installed
by a qualified electrician. This appliance
is designed for use on a nominal 120-volt
circuit, and has a grounding attachment
plug that looks like the plug in the
drawing above. Make certain that the
appliance is connected to an outlet
having the same configuration as the
plug. No plug adapter should be used with
this appliance.
■
■
■
■
■
■
■
■
This model is for household uses only.
3
w w w . b i s s e l l . c o m
8 0 0 . 2 3 7 . 7 6 9 1
ug310-5868_1699_306.indd
3
3/1/06 3:13:33 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
TurboBrush®
Storage
(Select Models)
SmartTemp™
Ready Light
Flow Indicator
(Filter Inside)
SmartMix®
Switch
Lower Handle
SmartMix®
Tank
ReadyTools™ Dial
Belt Access Door
DirtLifter®
PowerBrush
Floor Nozzle
Window
Optional Accessories:
These items are available for purchase with your model. To order replacement parts or additional tools or
formulas, please refer to page 19.
TurboBrush®
3” Tough Stain Brush
4” Upholstery Tool
PreTreat Wand
Bare Floor Attachment
Spraying Crevice Tool
w w w . b i s s e l l . c o m
Scotchgard™ protector applicator
MeshTool Bag
(bag only)
8 0 0 . 2 3 7 . 7 6 9 1
4
ug310-5868_1699_306.indd
4
3/1/06 3:13:34 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Keep plenty of genuine BISSELL
Advanced Cleaning Formulas on hand
so you can clean whenever it fits your
schedule. Always use genuine BISSELL
deep cleaning formulas. Non-BISSELL
cleaning solutions may harm the
machine and will void the warranty.
Trigger
Tool Caddy
Upper Handle
Power Cord
Quick Release
SmartTemp®
Switch
Tough Stain
Brush Storage
Tank-in-Tank™
Hex Nuts
4" Upholstery
Tool Storage
(Select Models)
Handle Release
Flex Hose
BISSELL Formulas:
48 oz. Fiber
48 oz. Multi-
48 oz. Pet Odor 48 oz. BISSELL
22 oz.
32 oz.
8 oz. Scotchgard
Cleansing Formula™ Allergen Removal™ and Soil Removal™ Natural Orange
Tough Stain Hard Floor Protector Post
PreCleaner™ Solutions™ Treatment
Cartridge
with Scotchgard™ Formula™ with
Protector
Formula with
Scotchgard™
Protector
Extract Formula with
Scotchgard™
Protector
Scotchgard™ Protector
5
w w w . b i s s e l l . c o m
8 0 0 . 2 3 7 . 7 6 9 1
ug310-5868_1699_306.indd
5
3/1/06 3:13:35 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
How to Use this Guide
This User’s Guide has been designed to help you
get the utmost satisfaction from your BISSELL
ProHeat. You’ll find assembly and operating
instructions, safety precautions, as well as
maintenance and troubleshooting instructions.
Please read this Guide thoroughly before
assembling your Deep Cleaner.
Pay particular attention to the product diagram, assembly
instructions, and part names. Locate and organize all parts
before assembly. Familiarize yourself with the parts and
where they go. Following this User’s Guide will greatly
enhance your ability to get the most performance from your
BISSELL ProHeat for many years.
WARNING:
Do Not plug in your
cleaner until you have
completely assembled it per
the following instructions
and are familiar with all
instructions and operating
procedures.
Your ProHeat comes in three, easy to
assemble components:
1
3
5
2
4
6
Upper Handle
Lower Handle
Tool Caddy
The only thing you will need to assemble your cleaner is
a Phillips head
screwdriver.
Assembling Your ProHeat
Refer to Assembly Diagram on page 5
1. Slide Upper Handle onto Lower Handle.
2. Feed bundled power cord through Tool Caddy from
caddy’s flat side.
3. Align Upper Handle holes and Tool Caddy holes.
4. Place hex nut into back of Tool Caddy and hold in
place. Insert bolt from front to back turning into the
hex nut until snug. Do not over tighten. Repeat for
the second bolt and hex nut.
ON
OFF
5. Insert 2 screws into lower 2 holes. Turn until snug.
6. Snap tools into Storage on the Tool Caddy.
7. Wrap Power Cord and Flex Hose as shown in
figure 7.
ProHeat assembly is now complete.
7
ON
OFF
w w w . b i s s e l l . c o m
8 0 0 . 2 3 7 . 7 6 9 1
6
ug310-5868_1699_306.indd
6
3/1/06 3:13:44 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Special Features of Your BISSELL ProHeat
Your BISSELL ProHeat Deep Cleaner is a home
cleaning system that automatically mixes hot
tap water with BISSELL advanced cleaning
formulas and heats the solution as it is applied
to the carpet. The combination of heated solution,
rotating brushes and powerful suction provide a
safe and effective method of cleaning.
SmartTemp®
SmartTemp Ready Light
The BISSELL ProHeat models all feature a
patented built-in heater which will heat hot tap
water you put in up to 25° degrees hotter to
safely optimize cleaning effectiveness. The
heater will never allow the temperature to
exceed 180°. The Heater Switch which is located
on the back of the machine controls the Heater
so you have the option to turn off the heat if you
are cleaning delicate wool or oriental rugs.
DirtLifter® PowerBrush
The DirtLifter PowerBrush is designed to
enhance cleaning performance. The bristle
pattern safely lifts out the deep down dirt while
gently grooming carpet fibers. The floating
suspension self-adjusts to all carpet heights.
When the power is ON ( I ) and the machine is
in the upright position, your carpet is protected
because the brushes are lifted up off the carpet.
SmartMix®
The SmartMix feature automatically mixes hot
tap water with the BISSELL advanced cleaning
formula. Simply choose one of the 3 settings
(High Traffic, Normal, or Water Rinse) and the
ProHeat will adjust the right amount of cleaning
solution to mix with the heated water to fit your
cleaning need.
SmartMix bottle
Having a separate solution tank from the
water tank allows no waste of formula.
Because the water and solution are stored
separately, they are not mixed until you are
ready to clean. When your cleaning job is
finished, the formula can be stored ready to
use in your machine for the next time!
This feature is available on all ProHeat models.
7
w w w . b i s s e l l . c o m
8 0 0 . 2 3 7 . 7 6 9 1
ug310-5868_1699_306.indd
7
3/1/06 3:13:45 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Scotchgard™ Protector Applicator Tool and Scotchgard Warranty
Carpet protection applied at the mill typically
wears down over time from heavy foot traffic
and everyday cleaning, including deep cleaning.
To help restore this important protection, only
BISSELL offers deep cleaning formulas with
Scotchgard protector as well as a post-applicator
to apply the same Scotchgard protector used by
carpet mills. This offers extra protection against
dirt and tough stains to keep your carpets looking
good longer.
To maintain your Scotchgard 5-year
limited stain warranty, you no longer are required
to hire a professional. By using your BISSELL
ProHeat machine with BISSELL formulas containing
Scotchgard protector every 12 months, your carpet
warranty from 3M remains in effect. No other home
deep cleaning system can do this for you. Refer to
the Scotchgard protector warranty for details.
Tank-in-Tank™
Our tank in tank system is designed with a heavy
duty bladder inside for clean water. As you clean,
the clean water in the bladder will empty and mix
with the cleaning formula. Dirty water pulled out
of your carpets will collect around the outside
of the bladder so that clean and dirty water are
always kept separate. This allows the user to
maximize tank space, yet only carry one tank to
and from the sink for emptying and filling.
Ready Tools Dial
This provides either floor cleaning or above
the floor cleaning with the flip of a switch. If
choosing above floor cleaning for upholstery,
stairs, or along the baseboards, choose the
attachment appropriate for the job. Attach tool
to the hose, and you are ready to go!
Flow Indicator
Flow Indicator
This is located on the machine base. It spins
when the trigger is pressed to indicate that the
machine is applying cleaning solution to the
carpet and will stop spinning when the SmartMix
tank or Bladder needs to be refilled, or when the
trigger is released.
T
TOOLS
PRETREA
FLOOR
CLEANING
Note: Flow Indicator does not spin when
spraying through the attachment hose.
ReadyTools Dial
w w w . b i s s e l l . c o m
8 0 0 . 2 3 7 . 7 6 9 1
8
ug310-5868_1699_306.indd
8
3/1/06 3:13:45 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Before You Clean
1. Plan activities to give your carpet time to dry.
2. Move furniture to another area if cleaning an
entire room (optional).
U
H
C
I
N
9
10
EXIT
8
11
3’
12
3. Thoroughly vacuum area with a dry vacuum
7
1
T
AR
ST
HERE
6
5
2
cleaner before deep cleaning.
3
4
4. Plan your cleaning route to leave an exit path. It is best
to begin cleaning in the corner farthest from your exit.
5. Pretreating (optional)
Note: Pretreating is recommended to improve
cleaning effectiveness for heavily soiled carpet in
high traffic areas such as entryways and hallways.
A. Spray the BISSELL Tough Stain Pre-treat formula
onto heavy traffic areas, soiled areas, or stains.
B. Allow to penetrate for at least 3 minutes.
C. Following the instructions below, clean as
normal, using the BISSELL ProHeat machine
on the High Traffic Setting.
ATTENTION:
Some Berber carpets have a
tendency to fuzz with wear.
Repeated strokes in the same
area with an ordinary vacuum
or deep cleaner may aggravate
this condition. Please see Stain
Removal instructions on page 15.
Carpet Cleaning
Fill The Water Tank
1
3
5
2
4
6
1. Release the handle and lay the machine handle
back to access the Tank.
2. Remove the Tank from the base of the machine by
lifting the Tank carry Handle.
3. Carry like a bucket to the sink. Rotate the Handle
forward to unlatch the lid. Lift off and set the lid aside.
4. Fill up the Bladder with clean hot tap water.
*Do not boil or microwave water as it can
destroy the Bladder.
5. Replace the top of the Tank by matching the lid
and tank edges. Handle must be in the forward
position in order to replace lid. Rotate the handle
to the carrying position to latch the lid.
Note: Remember to secure the lid and test to
make sure it is secure before picking up the Tank.
6. Place tank into machine base, seating firmly in place.
Rotate tank handle back into latched position. Bring
machine handle back into upright position.
Fill The SmartMix/Formula Tank
1. Lift the formula Tank up and out of the machine base.
2. To fill the Formula Tank, first unscrew the Cap
and Insert. Always use genuine BISSELL formulas
to maximize cleaning and for the safety of your
machine. Fill formula up to the line and replace the
Cap and Insert. Place Formula Tank back into the
base of machine, making sure it is seated securely.
Note: If bottle leaks, check for proper positioning
of red gromment and straw.
1
2
9
w w w . b i s s e l l . c o m
8 0 0 . 2 3 7 . 7 6 9 1
ug310-5868_1699_306.indd
9
3/1/06 3:13:49 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Choose The SmartMix Setting
Simply choose one of the 3 settings
• High Traffic
• Normal
• Water Rinse/Carpet Protector
and the ProHeat will adjust the right amount of
cleaning solution to mix with the heated water to
fit your cleaning need.
WARNING:
To Reduce the Risk of Fire and
Electric Shock due to internal
component damage, use only
BISSELL cleaning fluids intended
for use with the deep cleaner.
When filling bottle or
storing unit, set
NOTE: When your cleaning job is finished,
the formula can be stored ready to use in
your machine for the next time!
dial to:
SmartMix Dial
Set Ready Tools Dial
Set Ready Tools Dial to the Floor Cleaning Setting.
Power Switch
1. Plug into a proper outlet and turn the Power and
Heater switches to the ON ( I ) position. The
switches are found on the back of the handle.
Allow 1 minute for the built-in heater to warm-up
before cleaning. The ProHeat will be fully warmed
and will provide optimal performance after a
minute of continuous heated cleaning.
ReadyTools Dial
LS
TOO
T
PRETREA
G
OR
FLO
CLEANIN
2. The SmartTemp ready light indicates when the
heater is ON ( I ).
Note: SmartTemp heats the cleaning solution
for carpet and bare floor application only. It
does not heat solution sprayed through the
accessory tools.
Tip:
Deep Cleaning stairs and high traffic areas on
a regular basis can prolong carpet life.
Cleaning strokes
Power Switch
1. While pressing the Trigger, make one slow forward
wet pass and another one back. Let the Built-In
Heater, formula, and DirtLifter PowerBrush do the
work for you. Caution: Do not overwet. Take care
not to run over loose objects or edges of area rugs.
Stalling brush may result in premature belt failure.
1
SmartTemp Switch
ON
ON
OFF
OFF
2. Release the Trigger and make one slow forward and
backward pass over the same area to remove any
residual dirty water, and aid in drying. Repeat cleaning
passes until solution being pulled up appears clean.
Continue passes without pressing the trigger until you
can’t see any more water being pulled up.
SmartTemp Light
2
NOTE: Both the SmartMix tank and the
clean water tank must have liquid in them
in order for the machine to spray. If one
tank is empty the machine will not apply
cleaning solution or water.
3. After cleaning, you may want to turn the SmartMix dial
to Rinse to give your carpeting a final water only rinse.
This will ensure thorough removal of embedded dirt
loosened by the deep cleaning formula. BISSELL deep
cleaning formulas contain an anti-resoiling agent that
helps your carpets repel dirt and keeps them looking
good longer.
WARNING:
To reduce the risk of fire,
electric shock or injury,
unplug from the outlet
before servicing.
w w w . b i s s e l l . c o m
8 0 0 . 2 3 7 . 7 6 9 1
10
ug310-5868_1699_306.indd 10
3/1/06 3:13:50 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Empty The Tank
1. Remove the Water Tank from the base using the Tank
Carry Handle. Carry the Tank like a bucket to a utility
sink or outside where you will dispose of the collection
water. Remove the top of the Tank by rotating the
handle forward to unlatch lid and lifting lid off tank.
2. Empty collection water from bottom of tank.
NOTE: You may notice hair & debris deposits
on the carpet or in the Tank that were
loosened by the cleaning action (especially
with newer carpets that have never been
deep cleaned before). This debris should be
picked up and thrown away.
2
4
1
3
5
3. After each use, remove and rinse the lint screen
located on the Tank lid.
4. Refill the Tank in tank by referencing “Fill the
Water Tank” on page 9. Remember to secure the
top of the Tank by rotating the handle and test to
make sure it is secure before picking up.
5. Return Tank-in-Tank to the machine.
NOTE: Always check the level of cleaning
formula in the SmartMix Tank at the same
time, and refill as needed.
Rinse (Optional)
Rinsing is an optional step that can be done
during the cleaning process by switching to the
Water Rinse setting, or it can be done after the
carpeted area has been cleaned.
1. Simply choose the Water Rinse setting on the
SmartMix Dial, and follow the same path as you
did for cleaning, taking care to do a forward (wet)
stroke by depressing the trigger, a backward (wet)
stroke, and a forward and backward (dry) stroke,
releasing the trigger. Continue this until the water
you see coming up the nozzle is clear.
1
After Cleaning
Machine Storage
Once your cleaning is complete, make sure the
Water Tank is emptied and rinsed out. Put the
unit away in a closet or basement for the next
use. The SmartMix Tank can remain filled and
ready to go (store with machine set to Water
Rinse setting), or it can simply be emptied back
into the formula bottle if that is more convenient.
Note: Store cleaner in a protected, dry area.
Since this product uses water, it must not be
stored where there is a danger of freezing.
Freezing will damage internal components
and void the warranty.
WARNING:
To reduce the risk of fire,
electric shock or injury,
unplug from the outlet
before servicing.
11
w w w . b i s s e l l . c o m
8 0 0 . 2 3 7 . 7 6 9 1
ug310-5868_1699_306.indd 11
3/1/06 3:13:52 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
After Cleaning (Continued)
Machine Care
For best results, a few simple steps can assure
your machine is well maintained after your
cleaning is complete.
Flow Indicator
1. Turn Power and Heater switches OFF ( 0 ). Unplug
the machine and wrap the power cord.
2. After emptying the Water Tank, rinse it out at a
faucet with running hot tap water, taking care to
clean underneath the Heavy Duty Bladder, and all
around it. Clean out lint trap.
3. Replace the Tank in tank on the machine.
4. Clean out the flow indicator filter each time it is used
to ensure best cleaning performance. Unscrew the
Flow indicator cap, lift out the red rotor and white
filter. Rinse all three parts with water. Replace the
filter and rotor. Replace the Flow indicator cap. Turn
until snug, do not over-tighten.
4
5. Any loose hair or debris can be pulled from the
brush roll if desired and thrown away.
6. Wipe the machine’s exterior with a soft cloth.
7. After carpet is dry, vacuum again to remove hair and fuzz.
Post-Treatment Scotchgard Protector* (Optional) (*Available on select models)
Some ProHeat models are equipped with a
Scotchgard Protector post treatment applicator and
cartridge. Using this, along with one of the BISSELL
cleaning formulas containing Scotchgard, helps
to retain the carpet cleanliness achieved with the
ProHeat machine. For best results, the post cleaning
treatment should be applied while the carpet is still
damp. It is recommended that the Scotchgard
Tip:
protector be applied every 12 months to all clean
If clogged, soak applicator tool
in hot tap water before using.
carpeted areas, and after every deep cleaning for high
traffic areas such as entry ways and stairs.
1. Immediately after cleaning and rinsing your carpets,
empty the Water Tank and refill the Heavy Duty
Bladder with clean, hot tap water.
3
4
2. Set the Ready Tools dial to the Tools/Pretreat setting.
This will allow spray from the hose.
3. Purge the hose to eliminate cleaning solution from
the tube by spraying clean water through the hose
without attachments into a sink for 15-30 seconds.
4. Attach Scotchgard post-applicator cartridge to the
Applicator Tool, following the instructions on the
cartridge. Attach the combined Tool/Cartridge to
the hose. The water from the Tank in Tank will
automatically mix with the concentrated Scotchgard
post-treatment formula contained in the cartridge.
5. Turn the SmartMix Dial to the Water Rinse/Carpet
Protector setting.
w w w . b i s s e l l . c o m
8 0 0 . 2 3 7 . 7 6 9 1
12
ug310-5868_1699_306.indd 12
3/1/06 3:13:52 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Post-Treatment Scotchgard Protector* (Optional) (Continued)
6. Before applying Scotchgard protector to a large
area, test in a small, hidden area for colorfastness.
Examine area when dry. If color is affected, do not
use. For use on upholstery, look for manufacturer’s
cleanability code tag. Use only on fabrics coded
“W” or “WS”. If coded “S” or “X”, do not use. Not
recommended for use on velvet, silk vinyl, leather,
or 100% cotton upholstery.
7
7. Apply Scotchgard protector in a slow sweeping
motion with a slight overlap of the treated area. For
best coverage, follow the guide on the cartridge.
8.
One 8 oz. cartridge protects 200 square feet
(18.6 sq. meters). This is equal to two average
size rooms, (each at 10 x 10 ft. or 3 x 3 meters).
Periodically check the product level in the bottle to
ensure the best coverage.
9. Be careful not to spray the protector onto furniture
or fabric that has not been tested for colorfastness.
If this does occur, wipe off the protector.
11
10. When finished remove the bottle from the spraying
applicator tool. If concentrate is left, replace the cap to the
cartridge and store at room temperature for later use.
11. With the applicator tool still on the end of the hose,
spray clean hot water into the sink to avoid any
future clogging.
12. Store tool in a convenient location for use the next time.
Cleaning with Attachments
Your ProHeat machine comes equipped with a
hose and at least one attachment for cleaning
stairs, upholstery, and more.
1. Important! If using to clean Upholstery, check
Upholstery Tags.
A. Check manufacturer’s tag before cleaning.
“W” or “WS” on the tag means you can use
your ProHeat. If the tag is coded with an “X”
or an “S” (with a diagonal stripe through it),
or says “Dry Clean Only”, do not proceed
with any deep cleaning machine. Do not
use on Velvet or Silk. If manufacturer’s tag
is missing or not coded, check with your
furniture dealer.
Manufacturer’s tag
B. Check for colorfastness in an inconspicuous place.
C. If possible, check upholstery stuffing. Colored
stuffing may bleed through fabric when wet.
D. Plan activities to allow upholstery time to dry.
E. Vacuum thoroughly to pick up loose debris and
pet hair. Use a vacuum with a brush attachment
and a crevice tool to clean in fabric folds.
2. Follow the instructions on page 9 for filling the
Water Tank and the Formula Tank.
WARNING:
To reduce the risk of
injury, be extra careful
when cleaning stairs.
Make sure machine is
secure and level.
13
w w w . b i s s e l l . c o m
8 0 0 . 2 3 7 . 7 6 9 1
ug310-5868_1699_306.indd 13
3/1/06 3:13:53 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Cleaning with Attachments (Continued)
3. Set Ready Tools Dial to the Tools/Pretreat Setting. This
will allow spray and divert the suction to the hose.
*SmartTemp heats the cleaning solution for
carpet and bare floor application only. It
does not heat solution sprayed through the
accessory tools.
Tip:
Deep cleaning carpeting and
upholstery with BISSELL
Multi-Allergen Removal
Formula™ with Scotchgard™
protector regularly can
reduce dust and allergens
in your home.
4. Set SmartMix Dial to Normal.
5. Attach the cleaning tool to the end of the hose.
6. Plug in and turn on the Power Switch.
7. Clean by pressing the trigger to spray solution
onto the area to be cleaned. Slowly move the tool
back and forth over the soiled surface. Release
the trigger to suction soiled water. Continue to
clean in the area, working in small sections, until
no more dirt can be removed. Rinse (optional) and
suction as needed. Caution: Do no overwet.
8. When cleaning is complete, remove and rinse
tools in clean, running water.
5
9. Coil hose around the Tool Caddy.
10. Empty Water Tank and rinse out, following the
instructions on page 11.
11. Return Ready Tools Dial to Floor Cleaning.
WARNING:
Cleaning Fluid Section
To Reduce the Risk of Fire
and Electric Shock due to
internal component damage,
use only BISSELL cleaning
fluids intended for use with
the deep cleaner. Non-
BISSELL cleaning solutions
may harm the machine and
void the warranty.
Keep plenty of genuine BISSELL Fiber Cleansing
Formula™ and Scotchgard™ protector cartridges
on hand so you can clean and protect whenever
it fits your schedule. Always use genuine BISSELL
deep cleaning formulas.
48 oz. BISSELL
Fiber Cleansing
Formula™ with
Scotchgard™
Protector
48 oz. BISSELL
Multi-Allergen
Removal™ Formula
with Scotchgard™
Protector
48 oz. BISSELL
Pet Odor and Soil
Removal™ Formula
with Scotchgard™
Protector
48 oz. BISSELL
Natural Orange
Extract Formula with
Scotchgard™ Protector
item # 0740
item # 0710
item # 0720
item # 0730
w w w . b i s s e l l . c o m
8 0 0 . 2 3 7 . 7 6 9 1
14
ug310-5868_1699_306.indd 14
3/1/06 3:13:54 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Stain Removal
Do Not Delay! Attending to an accident soon
after it occurs ensures the chances for full
removal. Leaving it for an extended period of
time may cause it to set and become permanent.
1. Blot up liquids with an absorbent cloth or paper
towels. White materials are recommended because
certain dyes may bleed and make the stain worse.
2. Gently scrape up any semi-solids with a spoon or
spatula. Do not use a knife or other utensil with
sharp edges because it could damage the carpet
or upholstery.
3. If the area has dried, remove the remaining semi-
solids and residue with a sweeper or vacuum.
4. Be sure to test any spot removal formulas in an
inconspicuous area first. This is important as some
dyes and materials could be damaged or discolored
by cleaning solvents. If such a change should occur,
try a different solution or call a professional.
5. If cleaning on Berber carpeting, gently run your
machine over a hidden area. If no fuzzing occurs,
continue cleaning in soiled area.
6. Using the BISSELL Tough Stain PreCleaner, spray
evenly over soiled area. Do not overwet. Wait 3-5
minutes. Gently work the solution by blotting area
with a clean, damp, color safe cloth.
7. Clean using either the Floor Cleaning, or Tools/
Pretreat Setting on the Ready Tools Dial.
Bare Floor Cleaning
Your ProHeat model may have come with a
Bare Floor attachment and Hard Floor Solutions
Formula. If not, these products are available for
purchase by contacting the BISSELL Consumer
Services department by phone or on the website.
The Bare Floor tool provides effective cleaning
for linoleum, vinyl, and tile floors.
Caution: Do not use on hardwood floors.
1. Vacuum or Sweep thoroughly to pick up any loose
debris and pet hair.
2. Move any furniture, if needed.
3. Empty any carpet cleaning formula back into the
BISSELL bottle if stored in the Formula Tank. Fill
Formula Tank with BISSELL Hard Floor Solutions,
available at many retailers, or contact BISSELL
Consumer Services.
15
w w w . b i s s e l l . c o m
8 0 0 . 2 3 7 . 7 6 9 1
ug310-5868_1699_306.indd 15
3/1/06 3:14:02 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Bare Floor Cleaning (Continued)
4. Fill the Water Tank with Hot Tap Water and Set Aside.
5. Attach the Bare Floor Tool onto the Floor Nozzle with
the long tab to the right side of the Floor Nozzle. First
attach left side (short tab) catching tab over nozzle
edge. Gently bend long Tab (right side) outward to
easily snap over edge of clear nozzle on left.
6. Set the Ready Tools Dial to Floor Cleaning.
7. Set the SmartMix Dial to Normal Clean.
8. Plug into an outlet and turn the Power Switch and
Heater ON ( I ).
Bottom Front Edge
of Floor Nozzle
9. Slowly move the machine forward and back over
bare floor surface one time while pressing trigger.
Caution: Do not overwet.
Bare Floor
Cleaning Tool
Snap Together
10. Repeat the motion without pressing the trigger.
This allows the Bare Floor tool to squeegee and
suction up the dirty water.
11. Allow approximately 30 minutes for floors to dry.
12. Remove Bare Floor tool and rinse and dry
before storing.
13. If any formula remains in the Formula Tank, pour
it back into the Hard Floor Solutions bottle for use
the next time.
WARNING:
To reduce the risk of fire,
electric shock or injury
unplug from outlet before
servicing.
14. Rinse out the Formula Tank.
Troubleshooting / User Maintenance
SmartTemp Ready Light does not illuminate.
Possible Causes
Remedies
1. The SmartTemp Switch is not turned ON ( I ).
1. Turn ON ( I ) the SmartTemp
Switch.
2. The machine Power Switch is not
to turned ON ( I ).
2. Both switches must be ON ( I )
to activate the SmartTemp
Ready Light.
Reduced spray or no spray.
Possible Cause
Remedies
1. Bladder may be empty.
2. SmartMix Tank may be empty.
1. Refill Bladder with hot tap water.
2. Fill with BISSELL Fiber Cleansing
Formula for cleaning. Fill with
water if rinsing or using the
Scotchgard applicator.
3. The filter may be clogged.
4. Tanks may not be seated properly.
5. Pump may have lost prime.
3. Clean out Flow Indicator Filter,
page 12.
4. Turn power OFF (O); remove &
reseat tanks.
5. Turn power OFF (O); after 1
minute turn ON and press
Trigger.
w w w . b i s s e l l . c o m
8 0 0 . 2 3 7 . 7 6 9 1
16
ug310-5868_1699_306.indd 16
3/1/06 3:14:03 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting / User Maintenance (Continued)
Reduced spray or no spray. (Continued)
Possible Cause
Remedies
6. The Pump Belt may be broken.
6. Turn the machine OFF (O) and unplug
from the outlet. To check if a Pump
Belt has broken, you will need a flat
head screwdriver. Insert the blade
end into the lower slot of the Belt
Access door to release the lower
snap. If necessary, insert the blade
end into the upper slot to release the
upper snap. Examine the belt for
breakage. You should be able to
see the Pump Belt looped around the
motor shaft. If it is broken or missing,
please refer to Replacement Parts on
page 19 before calling Consumer
Services. Complete installation
instructions will accompany the
replacement belt.
Lift Here
Insert
Screwdriver
Blade Here
DirtLifter PowerBrush does not turn.
Possible Cause
Remedies
1. The Brush Belt or Pump Belt
is off or broken.
1. Turn the machine OFF (O) and unplug
from the outlet. To check if the Brush
Belt or Pump Belt has broken, you
will need a flat head screwdriver.
Insert the blade end into the lower
slot of the Belt Access door to release
the lower snap. If necessary, insert
the blade end into the upper slot to
release the upper snap. Examine the
belt for breakage. If broken, please
refer to Replacement Parts on page 19
before calling Consumer Services.
Complete installation instructions
will accompany the replacement belt.
Carpet Protector is not spraying. (Select Models Only)
Possible Cause
Remedies
1. Cartridge not connected to the tool.
1. Follow instructions on cartridge
assuring proper fit.
2. Solution clogging the Spray Trigger.
2. Soak applicator tool in hot water.
Spray without the cartridge attached to
purge any residual Solution left in the tool.
3.
3. Soak applicator tool in hot
Applicator tool spray is blocked.
water. Spray without the cartridge
attached to
purge any residual
Solution left in the tool.
17
w w w . b i s s e l l . c o m
8 0 0 . 2 3 7 . 7 6 9 1
ug310-5868_1699_306.indd 17
3/1/06 3:14:04 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting / User Maintenance (Continued)
Cleaner not picking up solution.
Possible Causes
Remedies
1. Ready Tools dial may be on the
wrong setting for the cleaning job.
1. Set ReadyTools dial to either or
Tools/PreTreat Floor Cleaning.
2. Nozzle Window may not be
properly attached.
2. Press down firmly on the black
oval gasket at the top window to
make sure the two tabs on the
back of the Nozzle Window are
snapped into the mating slots in
the main housing.
3. Tank-in-Tank lid is not properly installed.
4. Tank-in-Tank is not properly seated.
3. Re-install lid; refer to page 9.
4. Tank-In-Tank must be firmly
seated to function; remove and
reseat Tank-in-Tank.
5. Poor tool position.
5. Adjust angle; apply more
downward pressure.
(Hand held attachments only).
6. Tank-in-Tank has picked up
6. Empty Tank-in-Tank, refer to
page 11.
maximum dirty water.
Other Maintenance or Service not included above should be performed by an
authorized service representative.
Thank you for selecting a BISSELL product.
If you should happen to need assistance during assembly or operations, call 1-800-237-7691
Please do not return this product to the store
BISSELL Consumer Services
For information about repairs or replacement parts, or questions about your warranty, call:
BISSELL Consumer Services
1-800-237-7691
Monday - Friday
Saturday
8 a.m. — 10 p.m. EST
9 a.m. — 8 p.m. EST
Or write:
BISSELL HOMECARE, INC
PO Box 3606
Grand Rapids MI 49501
ATTN: Consumer Services
Or visit the BISSELL website - www.bissell.com
When contacting BISSELL, have model number of unit available.
Please record your Model Number: ___________________
Please record your Purchase Date: ___________________
NOTE: Please keep your original sales receipt. It provides proof of date of purchase in the event
of a warranty claim. See "About Your Warranty" on page 20 for details.
w w w . b i s s e l l . c o m
8 0 0 . 2 3 7 . 7 6 9 1
18
ug310-5868_1699_306.indd 18
3/1/06 3:14:04 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Replacement parts - BISSELL ProHeat
Below a list of common replacement parts*. While not all of these parts may have come
with your specific machine, all are available to you for purchase, if desired.
Item
1
Part No.
210-9201
Part Name
4” Small Area Tool
2
3
4
5
6
7
203-6655
203-6652
214-9131
214-9142
215-9155
015-9043
Spraying Crevice Tool
TurboBrush®
Bare Floor Tool
PreTreat Wand
Tough Stain Brush
Tank Assembly Complete (Includes lid assembly)
8
9
10
11
12
015-4439
015-9041
210-1785
210-1795
555-6503
Tank Lid Assembly
Tank Bottom
SmartMix® Tank (Includes Cap)
SmartMix® Cap Assembly
Flow Indicator Cap Assembly
13
14
15
16
214-9871
210-4052
215-0628
015-0621
Floor Nozzle Window and Gasket
Window Gasket
Replacement Pump Belt (With Instructions)
Replacement Belt Brush (With Instructions)
17
18
19
20
21
22
23
24
213-3501
0710
0720
0730
0484
0400
203-6691
0464
Lint Screen
Fiber Cleansing Formula™ 48 oz
Multi-Allergen Removal™ Formula 48 oz
Pet Odor and Soil Removal™ Formula 48 oz
Hard Floor Solutions™ 32 oz
Tough Stain PreCleaner™ 22 oz
Scotchgard Applicator Tool
Scotchgard protector Post Treatment Cartridge
*Not all parts are included with every model.
1
2
3
4
5
6
7
8
9
10
12
20
13
15
22
16
14
21
11
19
17
18
23
24
19
w w w . b i s s e l l . c o m
8 0 0 . 2 3 7 . 7 6 9 1
ug310-5868_1699_306.indd 19
3/1/06 3:14:05 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Warranty - BISSELL ProHeat
This warranty gives you specific legal rights, and you may also have other rights which may vary from state
to state. If you need additional instruction regarding this warranty or have questions regarding what it may
cover, please contact BISSELL Consumer Services by E-mail, telephone, or regular mail as described below.
Limited One Year Warranty
Subject to the *EXCEPTIONS AND EXCLUSIONS identified below, upon receipt of the product BISSELL
Homecare, Inc. will repair or replace (with new or remanufactured components or products), at BISSELL’s
option, free of charge from the date of purchase by the original purchaser, for one year any defective or
malfunctioning part.
See information below on "If your BISSELL product should require service".
This warranty applies to product used for personal, and not commercial or rental service. This warranty does not
apply to fans or routine maintenance components such as filters, belts, or brushes. Damage or malfunction caused
by negligence, abuse, neglect, unauthorized repair, or any other use not in accordance with the User's Guide is not
covered.
If your BISSELL product should require service:
Contact BISSELL Consumer Services to locate a BISSELL Authorized Service Center in your area.
If you need information about repairs or replacement parts, or if you have questions about your warranty,
contact BISSELL Consumer Services.
Website or E-mail:
Use the “Customer Services” tab.
Or Call:
BISSELL Consumer Services
1-800-237-7691
Monday - Friday 8 a.m. - 10 p.m. ET
Saturday 9 a.m. - 8 p.m. ET
Or write:
BISSELL Homecare Inc.
PO Box 3606
Grand Rapids MI 49501
ATTN: Consumer Services
BISSELL HOMECARE, INC. IS NOT LIABLE FOR INCIDENTAL OR
CONSEQUENTIAL DAMAGES OF ANY NATURE ASSOCIATED WITH THE
USE OF THIS PRODUCT. BISSELL’S LIABILITY WILL NOT EXCEED THE
PURCHASE PRICE OF THE PRODUCT.
Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above
limitation or exclusion may not apply to you.
*EXCEPTIONS AND EXCLUSIONS FROM THE TERMS OF THE LIMITED WARRANTY
THIS WARRANTY IS EXCLUSIVE AND IN LIEU OF ANY OTHER WARRANTIES EITHER
ORAL OR WRITTEN. ANY IMPLIED WARRANTIES WHICH MAY ARISE BY OPERATION
OF LAW, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO THE ONE YEAR DURATION
FROM THE DATE OF PURCHASE AS DESCRIBED ABOVE.
©2006 BISSELL Homecare, Inc
Grand Rapids, Michigan
All rights reserved. Printed in China
Part Number 310-5876
Rev 02/06
Visit our website at:
Scotchgard is a trademark of 3M
w w w . b i s s e l l . c o m
8 0 0 . 2 3 7 . 7 6 9 1
20
ug310-5868_1699_306.indd 20
3/1/06 3:14:14 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
|