1
2
OPTIONAL ACCESSORIES
R
EXHAUST HOSE KIT
P/N 400448. 5"(127mm) x10'
(3.05m). For blowing debris out
of hard-to-reach areas, around
buildings and shrubbery .
GUST ADJUSTER KIT P/
N 400615. Increases
blowing distance and
blowing control.
CREVICE CLEANER KIT
P/N 400620. Cleans out
cracks and crevices.
Thank You for Selecting
The Powerful QUIET BLOW
®
BLOWER
Operator Owner's Manual
For Models:
QB501CE
3
Specifications
UNIT SIZE:
OVERALL LENGTH: 51.75"(1.31m) OVERALL WIDTH 28.5" (0.72m)
OVERALL HEIGHT 39" (0.99m)
Part No. 400988
Page 1 of 8
Form No. F010496B
Download from Www.Somanuals.com. All Manuals Search And Download.
9
GENERAL SAFETY
For your safety and the safety of others, these directions should be followed:
Do not operate this machine without first reading
owner's manual and engine manufacturer's manual.
Use of Ear Protection is recommended while
operating this machine.
·DO NOT direct exhaust outlet toward any bystanders.
·DO NOT operate this equipment without first inspecting
work area.
·DO NOT operate this equipment during excessive vibration.
·DO NOT start engine without housing front plate attached.
·DO NOT operate this machine on slopes greater than 20%.
·DO NOT blow any hot or burning debris, or any toxic or
explosive material.
Use of Eye and breathing protection is recom-
mended when using this machine, especially in
dry and dusty conditions.
·DO NOT place hands or feet inside air intake opening, near
exhaust outlet or near any moving parts.
·DO NOT start engine without deflector attached to exhaust
outlet.
·DO NOT allow children to operate this equipment.
10
ASSEMBLY
Read all safety and operating instructions
before assembling or starting this unit.
1. Install upper handle (Item 28), to preassembled lower handle (item 29),
using two screws (Item 17), and two nut locks, (Item 32). Securely tighten
all fasteners.
2.Connect spark plug wire.
PUT OIL IN ENGINE BEFORE STARTING
NOTE: Front wheel bracket (Item 27), can be inverted to provide a
0.5” (12.7 mm) height adjustment.
Your Billy Goat is shipped from the factory in one carton,
completely assembled except for the upper handle
assembly.
11
PACKING CHECKLIST
These items should be included in your carton. If
any of these parts are missing, contact your dealer.
Boxing Checklist
28
Check
Handle Upper
Assembly
400957
29
32
Per Model
Check
Literature Assy
400565B
17
Literature
Assy
Per Model
Check
Briggs & Stratton 5
Engine
P/N MS9249
Multi-Language
HP
Manual
Page 3 of 8
Download from Www.Somanuals.com. All Manuals Search And Download.
Part No. 400988
Form No. F010496B
LITERATURE ASSY P/N 400565B
12
13
CONTROLS
Throttle Control-
(On Engine)
Set lever to choke position when
starting a cold engine
Literature Checklist
Owner's
Manual
Check
Owner's
Manual
400988
Check
Literature
Literature
QB
QB
Accessories
Accessories
RUN
OFF
CHOKE
400908
IDLE
FAST
Check
Warranty
Card
Warranty
Card
400972
Check
EU Declaration
of Conformity
400989
Set lever to desired engine
speed.
EU Declaration
of Conformity
Move lever completely to the left
to stop engine
Check
EU Distributor
List 900774
EU Distributor
List
14
ENGINE LABELS
INSTRUCTION LABELS
15
These labels should be included on your Blower. If any of
these labels are damaged, replace them before putting this
equipment into operation. Item and part numbers are given
to help in ordering replacement labels.
Briggs & Stratton
WARNING
EXPLOSIVE FUEL
STOP ENGINE AND ALLOW TO
COOL BEFORE REFUELING.
Read Owner’s Manual Before Operating.
Label Do Not Fill While
Engine Is Hot
Item 11 Part No.400268
Lire le manuel d’utilisation avant la mise en route.
Vor Inbetriebnahme Bedienungs - und Wartungsanleitung lesen.
Favor leer las instrucciones de operacion antes de operar el motor.
CL.ao.snSsuk.ol.ttasreeliinl MstarunkutaiolenUensoInenManaSnutatretn. zione prima dell utilizzo.
Label Danger Keep
Hands and Feet Away
Item 41 Part
No.400424
Label Read Owner's Manual
Item No. 59 Part No. 890301
DANGER
Label Ear Eye Breathing
Label Danger Flying Material
Item No. 63 Part No. 890254
Item No. 44 Part No. 810736
Part No. 400988
Form No. F010496B
Page 4 of 8
Download from Www.Somanuals.com. All Manuals Search And Download.
16
OPERATION
INTENDED USE: This machine is designed for cleaning
outdoor surfaces, where the debris can be effectively
blown into a consolidated area for convenient pickup and
removal.
Do not operate if excessive vibration occurs. If excessive
vibration occurs, shut engine off immediately and check
for damaged or worn impeller, loose impeller bolt, loose
impeller key, loose engine or lodged foreign objects.
Note: See parts list for proper impeller bolt torque specifi-
cations. (See trouble shooting section on page 8).
EXHAUST AIR DEFLECTOR ADJUSTMENT:
Like all mechanical tools, reasonable care must
be used when operating machine.
Inspect machine work area and machine before operat-
ing. Make sure that all operators of this equipment are
trained in general machine use and safety.
Fig. 2
Deflector adjusted downward
increases air velocity for
cleaning crevices and
PUT OIL IN ENGINE BEFORE STARTING
blowing heavier debris.
16.1
STARTING
ENGINE: See engine manufacturer’s instructions
for type and amount of oil and gasoline used.
Engine must be level when checking and filling oil and
gasoline.
Fig. 3
ENGINE SPEED: Controlled by throttle lever on the engine.
Under normal conditions, operate at minimum throttle to
accomplish your current cleaning task.
CHOKE: Operated with choke lever on face of engine .
THROTTLE: Move throttle control on face of engine to fast
position. Pull starting rope to start engine.
Optional Gust Adjuster gives operator remote deflector control
increasing blowing control and distance (see Optional Accessories
on page 1).
IFYOUR UNIT FAILSTO START:
See Troubleshooting on page 8.
16.2
BLOWING OPERATION
16.4
HANDLING &TRANSPORTING:
Adjust diverter rod to side discharge for normal blowing or to
forward discharge for blowing along walls, fences or hard-to-reach
areas (see Fig. 1).
Using two people to lift machine is recommended. Lift holding the
handle and frame. Secure in place during transport or when
unattended.
16.5
STORAGE
Never store engine indoors or in enclosed poorly venti-
lated areas with fuel in tank, where fuel fumes may reach an
open flame, spark or pilot light, as on a furnace, water heater,
clothes dryer or other gas appliance.
If engine is to be unused for 30 days or more, prepare as
follows:
Remove all gasoline from carburetor and fuel tank to
prevent gum deposits from forming on these parts and causing
possible malfunction of engine. Drain fuel outdoors, into an
approved container, away from open flame. Be sure engine is
cool. Do not smoke. Run engine until fuel tank is empty and
engine runs out of gasoline.
NOTE: Fuel stabilizer (such as Sta-Bil) is an acceptable alternative in minimizing
the formation of fuel gum deposits during storage. Add stabilizer to gasoline in
fuel tank or storage container. Always follow mix ratio found on stabilizer
container. Run engine at least 10 min. after adding stabilizer to allow it to reach
the carburetor.
Fig. 1
Page 5 of 8
Part No. 400988
Form No. F010496B
Download from Www.Somanuals.com. All Manuals Search And Download.
18
PARTS DRAWING
QB501CE
R
Page 6 of 8
Download from Www.Somanuals.com. All Manuals Search And Download.
Part No. 400988
Form No. F010496B
Item
No.
QB501CE
PARTS
LIST
19
Description
Part No.
Part No.
Part No.
QTY
Part No.
QTY
QTY
QTY
1
ENGINE -
5
HP BRIGGS & STRATTON
400220
1
2
3
4
5
6
7
8
9
LOCK CLIP
400218
1
7
1
1
1
1
1
WASHER SPRING LOCK 1/4 MED.
PLATE FRONT W.A. & GRILL
IMPELLER ASS’Y
KEY SQUARE 1/4 X 2 1/4
DIVERTER PLATE
*8177010
400960B
400421
*9201123
400334
AXLE
400571
WASHER LOCK 3/8 TWISTED TOOTH)
400502
1
10
.
SCREW CAP 3/8 -24 x 1" HEX. HD GR. 8 (TORQUE 50 FT LBS)(68N m)
LABEL DO NOT FILL WHEN ENGINE IS HOT
SHEET METAL SCREW 1/4 AB x 3/4 LG
COTTER PIN , 1/8 x 1
900154
400268
*8122082
*8197031
1
1
7
2
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
NUT LOCK 1/2 -13
SCREW CAP 5/16-18 x 1-1/2
*610323
*8041030
1
6
WASHER FLAT CUT 3/8
WHEEL FRONT 5"
*8171004
400249
*8041100
*8041026
400295
400974
400957A
400950
4
1
1
1
2
1
1
1
SCREW CAP, (FRONT AXLE) 5/16-18 x 2 -1/2"
SCREW CAP 5/16-18 x 3/4
WHEEL, REAR
BRACKET (FRONT WHEEL) 5"
HANDLE UPPER ASS’Y (incl. item 46)
HANDLE LOWER
SCREW CAP 5/16 -18 x 2-3/4
NUT LOCK , 5/16-18 HEX
NUT LOCK 5/16-18 THIN HT
*8041035
*8160002
*8161041
4
15
1
SCREW CAP 5/16 -24 NF x 3/4
*8042026
2
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
WASHER (0.765 1.0 x 1.25 OD x 0.06)
NUT LOCK 10-24
DEFLECTOR
LABEL DANGER HANDS & FEET
BOLT CARRIAGE 5/16 -18 x 1-3/4
WASHER - FLAT 3/4 S.A.E. (3/16 x 1-1/2 x 1/8 )
LABEL DANGER FLYING MATERIAL
WASHER 3/4 - HUB CAP
GRIP
KNOB 5/16-18
GUARD MUFFLER (COMES W/ ITEM 1 )
WASHER LOCK 5/16 EXT, TOOTH
SPACER
850238
*8164005
400333
400424
*8024043
*8172015
810736
850237
400570
890108
400990
*8181008
400330
400340
400332
400296
*8059135
400335
400576
900486
*8171003
890301
*8172009
900455
*8041021
890254
2
2
1
1
1
2
1
2
2
1
1
1
1
1
1
2
2
1
1
2
10
1
1
2
2
1
GRIP RING
SPRING COMPRESSION
SPACER
SCREW MACH. 10 -24 x 5/8 HEX W. F.
ROD DIVERTER
FRAME ASS’Y (INCLUDES 41, 44, 63 )
HUB CAP
WASHER FLAT CUT 5/16 ( 3/8 ID x 7/8 OD x1/16 )
LABEL READ OWNER'S MANUAL
WASHER -SAE 3/8 (13/32 x 13/16 x 3/32 )
NUT LOCK WASHER FACE 1/4 - 20
SCREW CAP 1/4 - 20 x 5 1/2 LG
LABEL EAR EYE BREATHING
Notes standard hardware that may be purchased locally.
Page 7 of 8
*
Part No. 400988
Form No. F010496B
Download from Www.Somanuals.com. All Manuals Search And Download.
17
MAINTENANCE
17.2
IMPELLER REMOVAL
Use only a qualified mechanic for
any adjustments, disassembly or
any kind of repair .
1. Wait for engine to cool and disconnect spark plug.
2. Remove front wheel (item 23),and front wheel bracket
(item 27).
WARNING: TO AVOID PERSONAL INJURY, ALWAYS
TURN MACHINE OFF, MAKE SURE ALL MOVING
PARTS COME TO A COMPLETE STOP.
3. Remove housing front plate (item 4), by removing seven
(7) screws (item 12), around outside of front plate.
4. Remove impeller bolt and lock washer.
NOTE: DO NOT PULL OR PRY ON IMPELLER BLADES.
5. Pull on center hub backplate area only of impeller. If
impeller slides off freely, proceed to (step 8).
DISCONNECT SPARK PLUGWIRE
BEFORE SERVICING UNIT.
6. Place two crowbars between center hub backplate area
of impeller and housing on opposite sides. Carefully pry
impeller away from engine until it loosens. Using a
penetrating oil can help loosen a stuck impeller.
7. If the impeller does not loosen, obtain a 1” (25.4mm)
longer bolt of the same diameter and thread type as the
impeller bolt. Thread longer bolt by hand into the crankshaft
until bolt bottoms. Using a suitable gear or wheel puller
against the bolt head and the impeller back-plate (near the
blades), remove impeller from shaft.
ENGINE: See engine manufacturer
operator's instructions.
RECONNECT SPARK PLUGWIRE AND
GUARDS BEFORE STARTING ENGINE.
17.1
8. Reinstall new impeller in reverse order of removal.
9. Tighten impeller bolt. Torque impeller bolt (see parts list
on page 7 for proper impeller bolt torque specifications).
Follow these hourly maintenance intervals.
Maintenance Schedule
Every
Use
Every 25
hrs.
Every 5 hrs.
or (Daily)
Maintenance Operation
Engine (See Engine Manual)
Check for excessive vibration
Inspect for loose parts
TIRE AIR PRESSURE: Check at regular intervals and
maintain.
Rear Tires only - 30 Psi. (21 kPa).
Inspect for worn or damaged parts
Lubricate wheels
20
Before Requesting Service Review These Suggestions
TROUBLESHOOTING
Possible Cause
Problem
Solution
Poor air performance
Air intake or exhaust clogged.
Clearclog.
Loose or out of balance impeller or loose engine.
Abnormal vibration.
Engine will not start.
Check impeller and replace if required. Check Engine.
Check throttle, choke position and gasoline. Connect spark plug wire.
Clean or replace air cleaner. Or contact a qualified service person.
Throttle in off position. Engine not in full choke position. Out of
gasoline. Bad or old gasoline. Spark Plug wire disconnected.
Dirty air cleaner.
Contact an engine servicing dealer for engine problems.
Engine problem.
Engine is locked, will not
pull over.
WARRANTY PROCEDURE
Engine Service and Warranty
Contact your nearest engine manufacturer's autho-
rized servicing dealer.
22.1
Please fill in the WARRANTY CARD and send the upper part to Billy Goat.
The WARRANTY terms are stated on the lower part which remains with the
user. Whenever a Billy Goat Machine is faulty due to a defect in material
and / or workmanship, the owner should make a warranty claim as follows:
22
Record your machine model, serial number
Serial Plate
The Machine should be taken to the dealer from whom it was
purchased or to an authorized Billy Goat dealer.
21
and date-of-purchase and where purchased
1803 S. Jefferson
P.O. Box 308
The owner should present the remaining half of the Warranty
Lee's Summit,
MO 64063 / USA
Registration Card, or, if this is not available, the invoice or receipt.
R
L
A
Tel (816) 524-9666
Fax (816) 524-6983
The Warranty Claim will be filled in by the authorized Billy Goat Dealer,
who will send it with the faulty part to Billy Goat headquarters.
85
Model
Serial No.
The Quality / Service department at Billy Goat headquarters will study
the claim and parts and will notify their conclusions.
The decision by the Quality / Service department at Billy Goat
headquarters to approve or reject a Warranty claim is final and
binding.
L
A
p
Unit(Weight)
lbs.
Engine Power
kW
91
Operator
kg
rpm
min-1
Note: To process a Warranty Claim, it is necessary to quote the Model
& Serial number who are printed on the Billy Goat Serial Plate.
BILLY GOAT INDUSTRIES INC.
P.O.BOX 308 (1803 S JEFFERSON LEE'S SUMMIT, MO.64063 / USA
PHONE:816-524-9666 FAX:816-524-6983
Purchase
Date
Purchased
from
R
Page 8 of 8
Download from Www.Somanuals.com. All Manuals Search And Download.
Part No. 400988
Form No. F010496B
|