BiPAC 7401V(G)PX
3G/ VoIP/ (802.11g) ADSL2+
Firewall Router
Quick Start Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Billion BiPAC 7401V(G)PX 3G/ VoIP/ (802.11g) ADSL2+ Firewall Router
PLEASE READ THE QUICK START GUIDE AND FOLLOW THE
STEPS CAREFULLY. THIS QUICK START GUIDE WILL HELP YOU
INSTALL THE DEVICE PROPERLY AND AVOID IMPROPER USAGE.
IF YOU NEED MORE INFORMATION ON THIS SOFTWARE
CONFIGURATION, PLEASE REFER TO THE USER’S MANUAL ON
CD-ROM.
Package Contents
BiPAC 7401V(G)PX ADSL2+ Router
CD containing the on-line manual
RJ-11 ADSL/telephone cable
Ethernet (RJ-45) cable
One 2dBi detachable antenna (Wireless model only)
Power adapter
RJ-45 to RS-232 Console Kit
This Quick Start Guide
Splitter/ Micro-filter (Option)
ꢀ
ꢀ
Do not use the router in high humidity or high temperatures.
Do not use the same power source for the router as other
equipment.
ꢀ
ꢀ
Do not open or repair the case yourself. If the router is too hot,
turn off the power immediately and have it repaired at a qualified
service center.
Warning
Avoid using this product and all accessories outdoors.
ꢀ
ꢀ
Place the router on a stable surface.
Only use the power adapter that comes with the package. Using a
different voltage rating power adaptor may damage the router.
Attention
-1-
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick Start Guide
Hardware Overview
The Front LEDs
Lit green when the
USB device is ready.
Flashes when
Lit when connected to an
Ethernet device.
Green for 100Mbps;
Orange for 10Mbps.
Blink when data is
sending/ receiving
data.
Lit green when the
SIP Registration is
OK.
Lit Green when the device is
successfully connected to an
ADSL DSLAM. (“line sync”)
Transmitted / Received.
Lit green when the
phone is off hook.
Lit when power is ON.
Lit red means system
failure.
Lit green when a
Lit red when WAN port fails to
get IP address.
Lit green when WAN port gets
IP address successfully.
wireless connection is
established. Flash
when the device is
sending/receiving data.
Lit when the inbound
and outbound calls
are transmitted
through PSTN.
The Rear Ports
Press it to reset
the device or
restore to factory
default settings
Connect the
detachable
antennato this port.
Connect this port to
the telephone jack on
the wall with RJ-11
cable.
Connect the
supplied power
adapter to this jack
3G/ HSDPA USB
modem backup for
Internet access
Connect a UTP Ethernet
cable (Cat-5 or Cat-5e) to
one ofthe LAN ports when
connecting to a PC or an
office/home network of
10Mbps or 100Mbps.
Power
ON/OFF
switch
Connect this port to the
ADSL/telephone network
with the RJ-11 cable
Connect this port to
an analog phone set
with RJ-11 cable.
(telephone) provided.
Push WPS button to
trigger Wi-Fi Protected
Setup function.
-2-
Download from Www.Somanuals.com. All Manuals Search And Download.
Billion BiPAC 7401V(G)PX 3G/ VoIP/ (802.11g) ADSL2+ Firewall Router
Hardware Connection
Hardware Installation
1. Power Connection
Plug the supplied power adapter to the wall jack and the other side to the router.
Please note that the plug type may differ according to different countries.
2. LAN Connection
Connect the supplied RJ-45 Ethernet cable to one of the Ethernet ports, and the
other side to the PC’s Ethernet interface.
-3-
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick Start Guide
3. USB Connection
The USB 2.0 port supports 3G/HSDPA modem connectivity: users can
conveniently access Internet via 3G, eliminating the limitations of the wired
network. This solution also employs an auto fail-over feature to ensure always-on
connectivity for SOHO users.
4. Phone Connection
Connect RJ-11 cable to the router’s phone port and the analog phone set.
5. Line Connection
a) Connect RJ-11 cable to the router DSL port and the splitter ADSL port.
b) Connect RJ-11 cable to the router Line port and the splitter phone port.
c) Connect RJ-11 cable to the splitter Line port and the phone jack on the wall.
-4-
Download from Www.Somanuals.com. All Manuals Search And Download.
Billion BiPAC 7401V(G)PX 3G/ VoIP/ (802.11g) ADSL2+ Firewall Router
6. Splitter/ Micro-filter Connection
Splitter / Micro-filter are important for ADSL installation. It helps high-frequency
signals are directed to the ADSL modem, and low-frequency signals are directed
to the telephone or other analog voice-channel device to prevent inter-modulation
distortion and get good speed and stable ADSL sync rate.
a) Splitter connection
If the installation has only a single telephone and a single ADSL modem, then a
splitter can be employed.
b) Micro-filter connection
If the installation has several telephones or other analog devices, then an internal
micro-filter can be employed at each analog device.
Setup Utility
-5-
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick Start Guide
After you complete the hardware installation, insert the CD-ROM to the CD-ROM drive to
perform Setup Utility for network configuration. The Setup Utility will auto-run. Follow the
step-by-step configuration wizard, the utility will guide you complete the basic network
configuration.
Troubleshooting
1. None of the LEDs are on when you turn on the router.
Check the connection between the adapter and the router. If the error persists, you may have
a hardware problem. In this case you should contact technical support.
2. You have forgotten your router login and/or password.
Try the default login and password, please refer to the user manual. If this fails, you can
restore your router to its factory settings by holding the Reset button on the back of your
router for 6 seconds or more.
3. Can’t ping any PCs on the LAN.
Check the Ethernet LEDs on the front panel. The LED should be on for a port that has a PC
connected. If it is off, check the cables between your router and the PC. Make sure you have
uninstalled any software firewall for troubleshooting. Verify that the IP address and the subnet
mask are consistent between the router and the workstations.
4. Frequent loss of ADSL linesync (disconnections).
Ensure that all other devices connected to the same telephone line as your router (e.g.
telephones, fax machines, analogue modems) have a line filter connected between them and
the wall socket (unless you are using a Central Splitter or Central Filter installed by a qualified
and licensed electrician), and ensure that all line filters are correctly installed and the right
way around. Missing line filters or line filters installed the wrong way around can cause
problems with your ADSL connection, including causing frequent disconnections. If you have
a back-to-base alarm system you should contact your security provider for a technician to
make any necessary changes.
Product Support and Contact Information
Most problems can be solved by referring to the Troubleshooting section in the User’s Manual.
If you cannot resolve the problem with the Troubleshooting chapter, please contact the dealer
where you purchased this product.
Contact Billion
WORLDWIDE
Billion Product Registration
Billion is committed to before and after sales customer services. You will get the most out of your Billion's products
after registration. Please register online at www.billion.com/register to receive valuable services and support from
us.
7401V(G)PX: V1.00EN
-6-
Download from Www.Somanuals.com. All Manuals Search And Download.
|