Installation, Service and User Instructions
Built-in gas cooktops
BERTAZZONI
DIMENSIONS: 36’’ (915 mm)(W) x 253/16’’ (640 mm)(D)
Models C36500X (Z36500X)
Models C36600X (Z36600X)
[C3W0..U4X(2 or 5)A]
[C3Y0..U4X(2 or 5)A]
IMPORTANT - PLEASE READ AND FOLLOW
-Before beginning installation, please read these instructions completely and carefully.
-Do not remove permanently affixed labels, warnings, or plates from the product. This may void the warranty. -Please observe all local
and national codes and ordinances.
-Please ensure that this product is properly grounded.
-The installer should leave these instructions with the consumer who should retain for local inspector's use and for
future reference.
-The electrical plug should always be accessible.
Installation must conform with local codes or in the absence of codes, the National Fuel Gas Code ANSIZ223.1-latest edition. Electrical
installation must be in accordance with the National Electrical Code, ANIS/NFPA70
-
latest edition and/or local codes. IN CANADA:
Installation must be in accordance with the current CAN/CGA-B149.1 National Gas Installation Code or CAN/CGA-B 149.2, Propane
Installation Code and/or local codes. Electrical installation must be in accordance with the current CSA C22.1 Canadian Electrical
Codes Part 1 and/or local codes.
Installation of any gas-fired equipment should be made by a licensed plumber. A manual gas shut-off valve must be installed in the gas
supply line ahead of the oven in the gas flow for safety and ease of service.
In Massachusetts: All gas products must be installed by a "Massachusetts" licensed plumber or gasfitter. A "T" handle type manual
gas valve must be installed in the gas supply line to this appliance.
IMPORTANT: SAVE FOR LOCAL ELECTRICAL INSPECTOR’S USE.
READ AND SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
OBSERVE ALL GOVERNING CODES AND ORDINANCES.
WARNING: If the information in this manual is not followed exactly, a
fire or explosion may result causing property damage, personal injury
or death.
Do not store or use gasoline or other flammable vapors and liquids in
the vicinity of this or any other appliance.
WHAT TO DO IF YOU SMELL GAS
- Do not light any appliance.
- Do not touch any electrical switch.
- Do not use any phone in your building.
- Immediately call your gas supplier from a neighbor’s phone. Follow
the gas supplier’s instructions.
- If you cannot reach your gas suppliers, call the fire department.
Installation and service must be performed by a qualified installer,
service agency or the gas supplier.
310200
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION MANUAL
BACKGUARD INSTALLATION INSTRUCTION
Please follow the following installation instructions afther installing the cooktop:
1) Remove n°2 screws fixing worktop as shown in fig.1
2) Place front part of the backguard and attach it from bottom side with the two removed screws (point 2) as shown
in fig .2
3) Fix the front part of the backguard with the screws supplied with the backguard kit (fig.3)
4) Assemble back part with front part of backguard and fix them with a screw supplied with the backguard kit
(fig.4)
1
2
3
4
WORKTOP FRONTGUARD INSTALLATION INSTRUCTIONS
In order to increase the clearance between front edge of the worktop and the burners for your safety it is
recomended to install the worktop frontguard supplied with the appliance. For installation instructions follow
the instructions indicated in the following figures
3
Download from Www.Somanuals.com. All Manuals Search And Download.
PROXIMITY TO SIDE CABINET INSTALLATION
1. This rangetop may be installed directly adjacent to existing 36" (91.5 cm) high base cabinets. IMPORTANT: The top
2.Tgrhaeterasnugpeptoorpt MCUASNTNObeT3b/8e"i(n.s9t5alclemd)daibreocvtelythaedjaadcjeanctetnot bsiadseewcaallbsi,nteatllccoaubnitneerttOs,Pt.all appliances, or other side vertical
surfaces above 36" (91.5 cm) high. There must be a minimum of 6" (15.2 cm) side clearance from the rangetop to
3.3su. cWhitchoinmtbhues6tib" l(e15s.u2rfcamce)ssiadbeocvleeathraen3c6e"t(o9c1o.5mcbmus)tciboluenvteerrthiceailgshut.rfaces above 36" (91.4 cm) I the maximum wall
cabinet depth must be 13" (33.0 cm) and wall cabinets within this 6" (15.2 cm) side clearance must be 18" (45.7 cm)
4.4a.boWvaellthcaeb3in6e"t(s91a.b4ocvme ).thheighracnoguentoteprtmopu.st be a minimum of 36" (91.4 cm) for the open top burner models and a
minimum of 42" (106.7 cm) for the sealed burner models above the rangetop cooking surface for the full width of the
rangetop. This minimum height requirement does nQ1 apply if a rangehood is installed over the cooking surface.
A
B
C
D
E
F
6”(15.2cm) MIN
36”(91.5cm)
36”(91.5cm)
13”(33.0cm)MAX
18”(45.7cm)MIN
36”(91.5cm)
G
H
i
6”1/2(16.5cm)
1”(2.5cm) MIN
9/16” (1.8cm)
2”( 5 cm) MIN
L
120 VAC/60 Hz withing
48” (122.9cm) of right
rear or rangetop
4
Download from Www.Somanuals.com. All Manuals Search And Download.
COOKER HOOD INSTALLATION
The bottom of the hood should be 25 ½ " (65 cm) min. to 31 ½ " (80 cm) above the countertop. Refer to the rangehood
installation instructions for additional information. These dimensions provide for safe and efficient operation of the hood.
ELECTRICAL CONNECTION
This unit is manufactured for a polarized, grounded 120 volt/60 Hz, 16 amp system. Electric power consumption is about
1 W. The minimum of 102 VAC is required for proper operation of gas ignition systems. This circuit must be grounded
and properly polarized. The unit is equipped witth a SJT power cord, and in case of replacement, the cable shall be
replaced with one of the same type, size and length.
WARNING
Electrical Grounding Instructions
This appliance is equipped with a three prong plug for your protection against shock hazard and should be plugged
directly into a properly grounded socket. Do not cut or remove the grounding prong from this plug.
WARNING
ELECTRICAL SHOCK HAZARD
xꢀ Disconnect electrical power at the circuit breaker box or fuse before installing the appliance
xꢀ Electrically ground appliance
xꢀ Use copper conductors only. Failure to follow these instructions could result in seriuos injury or death
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Wiring diagram
For freestanding gas range model C36600X (Z36 6 00 X) C3Y0..U4X(2 or 5)A
CAUTION: label all wires prior to disconnection when servicing controls. Wiring errors can cause improper
and dangerous operation. Verify proper operation after servicing.
For freestanding gas range model C36500X (Z36 5 00 X) C3W0..U4X(2 or 5)A
CAUTION: label all wires prior to disconnection when servicing controls. Wiring errors can cause improper
and dangerous operation. Verify proper operation after servicing.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
GAS CONNECTION
All gas connections must be made according to national and local codes. This gas supply (service) line must be the
same size or greater than the inlet line of the appliance. This range uses a 1/2" NPT (see fig. in this chapter for details of
gas connections installations) inlet. Sealant on ali pipe joints must be resistive to LP gas.
1. Manual Shut-off Valve:
This installer-supplied valve must be installed in the gas service line ahead of the appliance in the gas stream and in
a position where it can be reached quickly in the event of an emergency. The manual shut-off valve shall be installed
properly in order to be accessible when appliance is installed in definitive position. In Massachusetts: A 'T' handle
type manual gas valve must be installed in the gas supply line to this appliance.
2. Pressure Regulator (see fig. in this chapter)
a) All cooking equipment must have a pressure regulator on the incoming service line for safe and efficient
operation, since service pressure may fluctuate with local demand. The pressure regulator is supplied
separately with the appliance; regulator has two female threads ½” NPT; it shall be installed properly in order
to be accessible when appliance is installed in definitive position.
b) Any conversion required must be performed by your dealer or a qualified licensed plumber or gas service
company. Please provide the service person with this manual before work is started on the range. (Gas
conversions are the responsibility of the dealer or end user.)
c) This range can be used with Natural or LP/Propane
7
REPLACEMENT PARTS
Only authorized replacement parts may be used in performing service on the appliance. Replacement parts are available
from factory authorized parts distributors.
CONVERSIONE TO DIFFERENT TYPES OF GAS
Before carrying out any maintenance work, disconnect the appliance from the gas and electric
supply. For Natural Gas fit regulator assembly described in Fig.
Adaptation of the pressure regulator for use with different type of gas
The pressure regulator supplied with the appliance is a convertible type pressure regulator for use with Natural Gas at a
nominal outlet pressure of 4” w.c. or LP gas at a nominal outlet pressure of 11” w.c. and it is pre-arranged from the
factory to operate with one of these gas/pressure as indicated in the pre-arranging labels affixed on the appliance,
package and Instruction booklet.
To convert the regulator for use with the other gas different from which one it is pre-arranged it is enough perform the
following operations:
1) Unscrew by hand the upper metal stopper of the regulator.
2) Unscrew by hand the white plastic piece screwed under the above mentioned metal stopper, afterward screw it again
in opposite way under the metal stopper (for gas reference see the written “LP” and “NAT” with relative indicating arrows
on the white piece).
3) Screw again by hand the metal stopper in the original position on the regulator.
Operating in this way the gas regulator is converted for use with the other gas/pressure.
- CHANGING THE NOZZLES FOR USE WITH OTHER TYPES OF GAS:
To change the nozzles of the burners use the following procedure:
Lift up the burners and unscrew the nozzles ( Fig.) using an adjustable spanner of 7 mm and change the nozzles with
those designed for the new gas supply according to the information given in TABLE shown below.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Models C36600X (Z36 6 00 X) [C3Y0..U4X(2 or 5)A]
Adapting to different types of gas
Burner
Auxiliary
Semi-Rapid
Rapid
Position
Injector
diam. [mm.]
0,90
Gas
Type
NG
Pressure
[i.w.c.]
4”
11”
4”
11”
4”
11”
4”
Max Rate
Min Rate
[BTU/h]
900
900
1500
1500
2500
2500
900
By-pass
diam. [mm]
Regulated
0,29
Regulated
0,36
Regulated
0,47
Regulated
0,29
[BTU/h] [W]
[W]
264
264
439
439
732
732
264
264
1318
1318
Front R
3400
3400
6100
6100
996
0,54
1,18
0,70
1,55
0,92
0,80
0,49
LP (Propane)
NG
LP (Propane)
NG
LP (Propane)
NG
LP (Propane)
NG
LP (Propane)
996
Rear L & C
Front C
Rear L
1787
1787
10400 3047
10400 3047
Front L Inner
Front L Outer
2800
2800
820
820
Dual Burner
11”
4”
11”
900
4500
4500
N°2 x 1,15
N°2 x 0,70
12000 3516
12000 3516
Regulated
0,65
Models C36500X (Z36 5 00 X) [C3W0..U4X(2 or 5)A]
Adapting to different types of gas
Burner
Auxiliary
Semi-Rapid
Rapid
Position
Injector
diam. [mm.]
0,90
Gas
Type
NG
Pressure
[i.w.c.]
4”
11”
4”
11”
4”
11”
4”
Max Rate
Min Rate
By-pass
Diam. [mm]
Regulated
0,29
Regulated
0,36
Regulated
0,47
Regulated
0,29
[BTU/h] [W]
[BTU/h]
900
[W]
264
264
439
439
732
732
264
264
1318
1318
Front R
3400
3400
6100
6100
996
0,54
1,18
0,70
1,55
0,92
0,80
0,49
LP (Propane)
NG
LP (Propane)
NG
LP (Propane)
NG
LP (Propane)
NG
LP (Propane)
996
900
Rear L and R
Rear L
1787
1787
1500
1500
2500
2500
900
10400 3047
10400 3047
Centre Inner
Centre Outer
2800
2800
820
820
Dual Burner
11”
4”
11”
900
N°2 x 1,15
N°2 x 0,70
12000 3516
12000 3516
4500
4500
Regulated
0,65
CAUTION: save the orifices removed from the appliance for future use
Regulation of burners
Work surface burner adjustment: follow the instructions below to adjust the work surface burner minimum:
1) Light the burner and set the knob to the MINIMUM position (small flame).
2) Remove the knob of the valve that is press fit on the rod of that valve.
3) The cooker is equipped with safety valves, use a small slotted screwdriver the choke valve located on the valve body
and turn the choke screw to the right or left until the burner flame is adjusted to minimum
4) Make sure that the flame does not go out when switching quickly from the MAXIMUM to the MINIMUM position.
WARNING: The above-mentioned adjustment should be made only for natural gas, while for operation with
liquid gas the screw must be locked at the end in a clockwise direction. The grill burner always
operates at maximum and therefore no minimum adjustment is required.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
SERVICE & MAINTENANCE INSTRUCTIONS
Service and maintenance only to be carried out by an authorised person
To replace parts such as burners, valves and electric components, the appliance must be open removing the worktop.
Note: if the valves must be replaced, first disassemble the ignitions switches wires.
It is recommended to replace the valve gaskets each time the valve is replaced, thus ensuring a perfect seal between the
body and the gas train.
WARNING: After first installation of the appliance or after any service intervention concerning main gas parts of
the appliance, make the leak test using water with soap on the gas connections in order to verify the correct
installation. Do not use fire for gas leak testing.
USER MANUAL
DESCRIPTIONS
DESCRIPTIVE CAPTION FOR HOB
DESCRIPTION OF HOBS
1. Small Burner
Model C36500X (Z36 5 00 X) [M3W0..U4X(2 or 5)A]Fig. A
Model C36600X (Z36 6 00 X) [M3Y0..U4X(2 or 5)A]Fig. B
2. Medium burner
3. Rapid burner
4. Dual burner
Fig. A
Fig. B
CONTROL PANEL DESCRIPTION
On the control panel, small symbols show the function of each knob or key. Here as follows are the several controls that
a cooker can have:
the symbol
shows the disposition of burners on the worktop, the full dot identifies the burner in object (in
this case the front burner on the right).
WARNINGS:
Keeping appliance area clear and free from combustible materials, gasoline and other flammable vapors and
liquid.
Do not store dangerous or flammable material in the cabinet areas above appliance; store them in a safe place
in order to avoid potential hazards.
For safe use of appliance, do not use it for space heating.
Do not use aerosol sprays in the vicinity of this appliance while it is in operation
10
Download from Www.Somanuals.com. All Manuals Search And Download.
USING BURNERS
A diagram is etched on the control panel above each knob which indicates which burner corresponds to that knob.
Manual ignition:
Manual ignition is always possible even when the power is cut off or in the event of prolonged power failure.
Turn the knob that corresponds to the burner selected counterclockwise to the MAXIMUM position at the etched star
(large flame) and place a lit match up to the burner.
Automatic electric ignition:
Turn the knob that corresponds to the burner selected anticlockwise direction to the MAXIMUM position at the etched
star (large flame) and then press the knob down to activate the spark ignition. Once ignited, keep pressing the knob for
about 10 seconds to allow the flame to heat the thermocouple. If the burner does not remain alight after releasing the
knob repeat the above procedure,
Note: It is recommended not to try to ignite the burner if the relative flame cap is not in the correct position
Note: Dual burner is composed by two burner (inside and outside); each one operates under the relative gas valve
indipendently from the other one.
Tips for using burners correctly:
WARNING: During use of each gas burner(s) adjust the burner flame size properly so it does not extend beyond
the edge of the cooking utensil. This is an instruction based on safety considerations
- Use suitable pots for each burner (see Fig. and Table )
- When the liquid is boiling, turn down the knob to the MINIMUM position.
- Always use pots with a cover.
Cinodircraetcetdfilnamfigeuraes(fplaemcte:)ꢀverify that aspect flame of the worktop burners be completely blue and with an aspect as
Table
Burner
Small
Medium
Large
Dual burner
Recommended pan diameters inches (mm)
35½”-551/8”(90 – 140)
551/8”- 1023/8”(140 – 260)
707/8”- 1023/8” (180 – 260)
862/3”-1023/8” (220 – 260)
WARNING: check the position of the burner caps before operation.
Correct usage of pans:
- Dry the bottom of the pan before placing it on the hotplate.
- Use pots with a flat, thick bottom, except for wok cooking.
- When using the burners, ensure that the handles of the pans are correctly positioned. Keep children away from the
appliance.
- When cooking foods with oil and fat, which are very flammable, the user should not leave the appliance unattended.
WOK PAN: To use the wok pan, please utilize a suitable wok adaptor grid; wok pan external diameter shall not be less
than 10” (25cm) and not more than 16”(40cm).
WARNING: If the power is cut off, the burners can be lit with matches.
The burners equipped with a safety thermocouple can only be lit when the knob is in the MAXIMUM position (large flame
etching).
11
Download from Www.Somanuals.com. All Manuals Search And Download.
CLEANING THE APPLIANCE:
Never use abrasive cleaners
Before cleaning the appliance it should be disconnected from the power supply.
Cleaning the work surface: periodically clean the burner heads, the cast iron pan supports and the burner caps using
warm water.
Any spillage must always be removed as soon as possible using a rag.
If it become difficult to open or close a valve, do not force it, but immediately request the assistance of the
technical service personnel.
Cleaning the enamelled parts: Enamelled parts should be cleaned frequently with soapy water. Never use abrasive
powder. Do not leave acidi or alkaline substances on the enamelled parts (such as vinegar, lemon juice, salt, tomato
sauce, etc.) and do not wash the enamelled parts while they are still hot.
Cleaning the stainless steel parts: Clean the parts with soapy water and dry them with a soft cloth. The shine is
maintained by periodically using specific stainless steel cream cleaner. Never use abrasive powders. Use specific
stainless steel cream cleaner to eliminate the glue remains afther the elimination of the blue plastic protection film on the
worktop after installation.
Cleaning the burner caps: Lift the burner caps from the burner heads and wash them in soapy water and dry
thoroughly. Before replacement on the burner head ensure that the holes are not clogged.
ATTENTION: for further details about cleaning of the appliance, please contact your applliance retailer.ꢀ
AFTER SALE SERVICE:
Please note here below details for after save service.
Refer to warranty certificate for warranty condiftions
Dealer /Importer:
Name, address, phone
SERVICE CENTERS
Name
Phone
MANUFACTURER:
BERTAZZONI SPA
VIA PALAZZINA, 8 – 42016 – GUASTALLA (REGGIO E.) ITALY
12
Download from Www.Somanuals.com. All Manuals Search And Download.
SPARE PART LIST
Quantity
Number
Drawing
Code Description
1
11
601739 CIRCUIT DIAGRAM
1
3
1
1
1
1
1
1
2
1
1
1
2
1
1
1
1
1
1
2
2
1
6
1
3
2
2
1
2
1
1
2
1
1
1
3
1
1
3
1
1
1
3
1
1
1
3
1
1
1
1
1
1
3
2
1
7
2
3
2
2
1
2
2
1
2
1
1
1
202317 PART FOR BURNER FIXING
202386 PART FOR DUAL WOK AND SEMI RAPID BURNERS
510507 SMALL BURNER
11
13
13
510508 SEMI RAPID BURNER
13
510509 RAPID BURNER
13
510511 DUAL BURNER
14
504128 SMALL FLAME SPREADER
504129 MEDIUM FLAME SPREADER
504130 RAPID FLAME SPREADER
504189 ULTRA RAPID FLAME SPREADER
504160 COVER FOR SMALL FLAME SPREADER
504161 COVER FOR MEDIUM BURNER
504162 COVER FOR RAPID BURNER
504186 COVER OUT FOR DUAL BURNER FLAME SPREADER
504187 COVER IN FOR DUAL BURNER FLAME SPREADER
404198 WORKTOP FRONTGUARD
202262 BRIDLE FOR FIXING GAS VALVES
502150 GAS VALVE BY PASS 065
502152 GAS VALVE BY PASS 036
502179 GAS VALVE BY PASS 029
502180 GAS VALVE BY PASS 047
306024 STOP SPRING FOR SPARK PLUG
415054 SPARK PLUG 350MM
14
14
14
15
15
15
15
15
55
160
163
163
163
163
385
415
415
415
430
473
583
583
583
583
648
702
715
715
961
961
1031
1143
1143
1602
1602
1603
1615
1624
1624
1627
1627
1628
415057 SPARK PLUG 700MM
415071 SPARK PLUG FOR DUAL BURNER
415065 ACCUMULATOR
404117 REDUCTIONGRID
508021 TERMOCOUPLE MM600
508025 TERMOCOUPLE MM300
508027 TERMOCOUPLE MM800
508032 TERMOCOUPLE FOR DUAL BURNER
601990 TERMINAL SEPARATOR
408058 ADAPTER FOR WOK BURNER PAN SUPPORT
604063 DASYCHAIN SWITCH
604062 DASYCHAIN SWITCH
1
2
1
6
1
1
408052 CAST IRON PAN SUPPORT 2 BURNERS
408053 CAST IRON PAN SUPPORT 1 BURNER
401904 GAS VALVE KNOB
3
7
1
1
1
410565 FRONT RISER
410566 REAR RISER
210464 CONTROL PANEL
210465 CONTROL PANEL
1
1
1
309119 BRIDLE FOR FIXING GAS VALVES/THERMOSTAT
202395 CONTROL SUPPORT
2
1
1
200317 WORK TABLE
200316 WORK TABLE
1
501624 GAS COLLECTOR
1
1
501625 GAS COLLECTOR
1
1
501646 TUBE FOR RIGHT FRONT BURNER
13
Download from Www.Somanuals.com. All Manuals Search And Download.
1631 501647 TUBE FOR RIGHT BACK BURNER
1800 501652 REAR CENTRAL TUBE
1
1
1
1
1
1
1
1
1801 501648 TUBE FOR LEFT BACK BURNER
1802 501653 FRONT CENTRAL TUBE
1803 501655 TUBE FOR EXTERNAL DUAL BURNER
1804 501654 TUBE FOR INTERNLA DUAL BURNER
1805 501650 CENTRAL TUBE
1806 501651 EXTERNAL CENTRAL TUBE
1807 501649 TUBE FOR FRONT LEFT BURNER
1
1
1
14
Download from Www.Somanuals.com. All Manuals Search And Download.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
|