EZ Melt,
Fill and Filter
Models EZ18, EZ24, AND EZ34
Operator’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
If you accept the machine from the shipping
company, you are, in effect, saying that the
machine is in good condition, and you must
pay for the machine. Belshaw cannot pay for
shipping damage, because the freight company
has accepted the machine from Belshaw in good
condition, and is responsible for its safe delivery.
For your protection, inspect the machine to see
that no parts are bent, scratched, or otherwise
damaged. If any damage has occurred in
shipping, file a freight claim with the shipping
company immediately.
EQUIPMENT RECORD
Please provide the information below when you correspond with us about your machine.
Purchased by _____________________________________________________________________
Installed by ______________________________________________________________________
Date of Installation ________________________________________________________________
Model number ___________________________________________________________________
Serial number
0103
MN-1316EN
Belshaw Bros., Inc.
1750 22nd Avenue South
Seattle, WA 98144-4590
Phone: (206) 322-5474 š Fax: (206) 322-5425
Toll Free: (800) 578-2547
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
2
Operation
Melting and Filling
Filtering
3
4
5
Cleaning
Troubleshooting
Parts List
16
18
20
22
24
26
28
EZ18-2000 Shortening Melter Assembly (120V)
EZ18-2001 Shortening Melter Assembly (240V)
EZ24-2000 Shortening Melter Assembly (120V)
EZ24-2001 Shortening Melter Assembly (240V)
EZ34-2000 Shortening Melter Assembly (120V)
EZ34-2001 Shortening Melter Assembly (240V)
EZ24/34-1000 Heater Head Assembly
6
Appendix
30
Insert
Insert
Wiring Diagram (EZ18-4002) - 120V, 50/60 Hz, 1 Ph
Wiring Diagram (EZ18-4003) - 208/240V, 50/60 Hz, 1 Ph
Belshaw Bros., Inc. š 1750 22nd Ave. S. š Seattle, WA 98144 š Phone 206-322-5474 š Fax 206-322-
5425
EZ Melt Model EZ18, EZ24, EZ34
MN-1316EN
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
Figures
1-1.
Front View.
1
2
1-2.
1-3.
1-4
Side View.
Top View, Heater Head.
Heater Head.
2
3
1-5
Elements & Kettle.
3
2-1.
2-2.
2-3.
2-4.
Packing Solid Shortening in the Kettle.
Cube Melter.
5
5
Installing the Cube Melter.
When to Add a Cube of Shortening.
5
6
2-4A. When to Add a Cube of Shortening. EZ-34 Only.
6
2-5.
2-6.
Positioning the Filter Frame for Melting.
When to Drain the Fryer.
6
7
2-6A. When to Drain the Fryer EZ-34 Only.
7
2-7.
2-8.
3-1.
5-1.
5-2.
5-3.
5-4.
5-5.
5-6.
5-7
Positioning the Filter Assembly for Filtering.
Rinsing Hose.
7
8
Removing the Heater Head.
10
17
19
21
23
25
27
29
EZ18-2000 Shortening Melter Assembly (120V)
EZ18-2001 Shortening Melter Assembly (240V)
EZ24-2000 Shortening Melter Assembly (120V)
EZ24-2001 Shortening Melter Assembly (240V)
EZ34-2000 Shortening Melter Assembly (120V)
EZ34-2001 Shortening Melter Assembly (240V)
EZ24/34-1000 Heater Head Assembly
Belshaw Bros., Inc. š 1750 22nd Ave. S. š Seattle, WA 98144 š Phone 206-322-5474 š Fax 206-322-
5425
iv
MN-1316EN
EZ Melt Model EZ18, EZ24, EZ34
Download from Www.Somanuals.com. All Manuals Search And Download.
Preface
The EZ Melt, Fill and Filter models EZ18, EZ24,
and EZ34 are designed to be used with Belshaw
fryers. It performs four functions:
š Make sure the EZ Melt kettle has enough
room in it before draining shortening
from the fryer. If you do not, shortening
may overflow the kettle and get on the
floor, possibly causing slips, falls, injury,
burns, or even death.
š It melts shortening
š It holds shortening
š It supplies shortening to the fryer kettle
š It filters used shortening for re-use
š Make sure the nozzle of the supply hose
is securely mounted on the side of the
fryer before turning on the pump. If you
do not, hot shortening could spray you,
resulting in serious burns. Also,
shortening could get on the floor,
possibly causing slips, falls, injury,
burns, or even death.
It is not designed to perform any other functions.
The EZ Melt, Fill and Filter uses electrical
elements to melt shortening.
The EZ Melt moves around on casters. It is
meant to be used on the floor. The operator of
the EZ Melt is expected to behave safely and to
read this manual and follow its instructions and
warnings.
š Make sure that the system and the
shortening are cool before attempting
any adjustments or repairs. If you do
not, you may be burned.
Study the instructions and warnings in this
manual carefully. A thorough understanding of
how to install, maintain, and safely operate the
EZ Melt, Fill and Filter will prevent production
delays and injuries.
š Be careful never to get shortening,
water, or other materials on the floor. If
anything does get spilled on the floor,
mop it up immediately. If you do not,
someone could slip or fall, be burned or
injured, or even die.
To use the EZ Melt safely, heed the following
warnings and all other warnings that appear in
this manual:
š To avoid damaging the EZ Melt, never
use force to assemble, disassemble,
operate, clean, or maintain it.
š Make sure all hose connections are tight.
If you do not, you may be sprayed with
hot shortening. This could result in
serious burns.
š To avoid electrocution, make sure that
the power cord is not frayed or cracked
and that it does not pass through any
water or shortening.
š Make sure no water gets into the
shortening. Water causes hot shortening
to spatter, which could cause serious
burns.
š Make sure that the power cord is routed
so that no one will trip over it.
Belshaw Bros., Inc. š 1750 22nd Ave. S. š Seattle, WA 98144 š Phone 206-322-5474 š Fax 206-322-
5425
EZ Melt Model EZ18, EZ24, EZ34
MN-1316EN
v
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
1
Installation
To help familiarize you with the major parts of
your EZ Melt model EZ18, EZ24, or EZ34, please study the
photographs below.
handle
heater head
filter assembly
kettle
casters
foot pedal
Figure 1-1. Front View.
Belshaw Bros., Inc. š 1750 22nd Ave. S. š Seattle, WA 98144 š Phone 206-322-5474 š Fax 206-322-
5425
EZ Melt Model EZ18, EZ24, EZ34
MN-1316EN
1
Download from Www.Somanuals.com. All Manuals Search And Download.
hose connector
filter assembly
heater head
power cord
kettle
frame with
casters
cube melter
foot pedal
Figure 1-2. Side View.
heating
element
kettle
hose connector
supply hose
Figure 1-3. Top View, Heater Head.
Belshaw Bros., Inc. š 1750 22nd Ave. S. š Seattle, WA 98144 š Phone 206-322-5474 š Fax 206-322-
5425
2
MN-1316EN
EZ Melt Model EZ18, EZ24, EZ34
Download from Www.Somanuals.com. All Manuals Search And Download.
Reset
button
Pump switch with
pilot light
Heat
switch
with pilot
light
Figure 1-4. Heater head
Bleeder
Pickup tube
Heating
element
kettle
Figure 1-5. Elements and kettle.
Belshaw Bros., Inc. š 1750 22nd Ave. S. š Seattle, WA 98144 š Phone 206-322-5474 š Fax 206-322-
5425
EZ Melt Model EZ18, EZ24, EZ34
MN-1316EN
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Thoroughly clean your EZ Melt before using it.
Refer to Section 3, “Cleaning,” for cleaning
instructions.
WARNING
Moisture causes hot shortening to spatter,
which may cause serious injury. Thoroughly
dry the kettle and any other parts you wash.
WARNING
To avoid electrocuting yourself or damaging
the EZ Melt, never allow water, steam,
cleaning solution, or other liquid to enter the
heater head.
Make sure that the power requirements of the EZ
Melt, shown on the data plate, match your power
source.
Belshaw Bros., Inc. š 1750 22nd Ave. S. š Seattle, WA 98144 š Phone 206-322-5474 š Fax 206-322-
5425
4
MN-1316EN
EZ Melt Model EZ18, EZ24, EZ34
Download from Www.Somanuals.com. All Manuals Search And Download.
2
Operation
Melting and Filling
1. Completely cover the heating element with
shortening. There are two ways to do this:
š Pre-melt some shortening in a pan on the
stove and pour it into the kettle to cover
the element.
š Pack solid shortening tightly around the
heating element and bulbs. Do not leave
any air spaces. Cover the heating element
at least 2”/5 cm. (See Figure 2-1)
Figure 2-2. Cube Melter
WARNING
Air spaces can cause the shortening to
overheat and catch on fire.
2. Install the cube melter in the kettle, opposite
the heater head. Push the cube melter through
Figure 2-3. Installing the Cube Melter.
3. Position the EZ Melt near the fryer.
4. Install the supply hose. Follow these steps:
a. Attach the hose to the pump outlet by
hand-tightening the hose connector.
the shortening so its legs rest on the bottom
of the kettle. (See Figures 2-2 & 2-3.)
b. Mount the nozzle of the hose on the edge
of the fryer kettle with the opening
inside the kettle.
Figure 2-1. Packing Solid Shortening in the
Kettle.
Belshaw Bros., Inc. š 1750 22nd Ave. S. š Seattle, WA 98144 š Phone 206-322-5474 š Fax 206-322-
5425
EZ Melt Model EZ18, EZ24, EZ34
MN-1316EN
5
Download from Www.Somanuals.com. All Manuals Search And Download.
5.
Make sure that the HEAT and PUMP
switches are in the OFF position. Connect
the EZ Melt to the power source.
SIDE OF
CUBE
MELTER
IF SHORTENING
LEVEL IS HERE
OR BELOW ADD
ONE CUBE OF
SHORTENING.
To avoid damaging the heating element, make
sure it is completely covered with shortening
before you turn the heater on.
BOTTOM OF
KETTLE
6. Turn the machine on using the HEAT
switch. When the heat is on, the heating
element melts shortening at 200“ F/93“ C.
The heat must also be on to operate the
pump.
Figure 2-4A. (EZ34 ONLY) When to Add a
Cube of Shortening.
To add a cube of shortening, follow these steps:
7. Turn the pump on using the PUMP switch.
1. Position the filter assembly so you can
add shortening. The edge of the kettle
has one or two sets of holes in it. Use
the set of holes that is nearer to the
heater head. When two of the filter
frame’s pins rest in these holes, the filter
assembly hangs vertically. (See Figure
2-5.)
8. When you want to supply shortening to the
fryer, press the foot pedal.
WARNING
To avoid burning yourself, never touch the
nozzle while the machine is in use.
9. When the fryer has enough shortening in it,
release the foot pedal.
10. As needed, add shortening to the kettle, one
cube at a time. Always add a cube if the
shortening level drops to the tops of the legs
of the cube melter. (See Figure 2-4 & 2-4A.)
IF
SIDE OF
CUBE
MELTER
SHORTENING
LEVEL IS
HERE OR
BELOW ADD
ONE CUBE OF
SHORTENING
Figure 2-5. Positioning the Filter Frame for
Melting.
BOTTOM OF
KETTLE
b. Place a solid cube of shortening on the
cube melter. Let one cube melt and be
pumped out before adding another cube.
Do not overload the EZ Melt.
Figure 2-4. When to Add a Cube of
Shortening.
Belshaw Bros., Inc. š 1750 22nd Ave. S. š Seattle, WA 98144 š Phone 206-322-5474 š Fax 206-322-
5425
6
MN-1316EN
EZ Melt Model EZ18, EZ24, EZ34
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Position the shortening filter assembly on
the EZ Melt kettle. The edge of the kettle
has one or two sets of holes in it. Use the
set of holes that is farther from the heater
head. When two of the filter frame’s pins
rest in these holes, the filter assembly rests
horizontally on the end of the kettle. (See
Figure 2-7.)
Filtering
1. Turn the fryer off. Allow the shortening to
cool to 130“ F/54“ C.
WARNING
Hot shortening may cause serious injury.
2. Turn the EZ Melt off. Make sure that both
the HEAT and PUMP switches are in the
OFF position.
3. Make sure that the top of the cube melter is
exposed.
If
shortening
level is
here or
Side of
Cube
Melter.
below
drain fryer.
Bottom of
kettle.
Figure 2-7. Positioning the Filter Assembly
for Filtering.
Figure 2-6. When to Drain the Fryer.
5. Disconnect the supply hose from the hose
connector. Hold the two ends of the hose up
so shortening does not drip out. Hang hose
vertically over a pan so the shortening will
drip into the pan.
If
Side of
cube
melter.
shortening
level is here
or below
drain fryer.
Bottom of
kettle.
6. Attach the rinsing hose securely to the hose
connector. (See Figure 2-8.)
Figure 2-6A. (EZ-34 ONLY) When to Drain
the Fryer.
WARNING
When you begin to drain the fryer, the
shortening in the EZ Melt must be shallow
enough for the top of the cube melter to be
exposed. If the shortening is deeper it might
overflow when you drain the fryer, thus
causing burns or other serious injury.
Belshaw Bros., Inc. š 1750 22nd Ave. S. š Seattle, WA 98144 š Phone 206-322-5474 š Fax 206-322-
5425
EZ Melt Model EZ18, EZ24, EZ34
MN-1316EN
7
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING
Thoroughly clean and dry the floor if
shortening, water, or other materials are
spilled. Materials spilled on the floor may
cause serious injury and loss of life.
11. After you have rinsed all the loose particles
out of the fryer kettle, release the foot pedal.
12. After the shortening has drained out of the
fryer kettle and through the EZ Melt filter,
close the drain valve.
13. Turn the EZ Melt off. Make sure that both
the HEAT and PUMP switches are in the
OFF position.
14. Disconnect the rinsing hose assembly. Hold
the two ends of the hose up so shortening
does not drip out. Hang the hose vertically
over a pan so shortening will drip into the
pan.
Figure 2-8. Rinsing Hose.
15. Bring the supply hose back to the EZ Melt,
holding the two ends of the hose up so
shortening does not drip out.
7. Position the EZ Melt so the filter is directly
under the drain in the fryer kettle.
8. Reach under the table and slowly open the
fryer’s drain valve.
16. Securely attach the supply hose to the hose
connector. Make sure the outlet nozzle is
securely mounted to the fryer, with the
opening inside the kettle.
9. Move the HEAT and PUMP switches of the
EZ Melt to the ON position.
17. Move the HEAT and PUMP switches to the
ON position. Press the foot pedal to supply
filtered shortening to the fryer.
10. Hold the insulated handle of the hose.
Direct the nozzle into the fryer kettle. Press
the foot pedal and rinse the kettle with
shortening. Do not let shortening splash out
of the kettle!
18. Before you filter shortening again, empty the
EZ Melt filter. Follow these steps:
a. Allow the filter assembly to cool to the
touch.
WARNING
b. Lift off the filter assembly, holding it by
the frame.
To avoid burning yourself, never hold or
touch the metal portion of the nozzle while
the machine is in use. Wear protective
gloves.
c. Invert the filter assembly over a sink or
garbage can and shake the sediment off
of it. DO NOT rinse the filter.
Belshaw Bros., Inc. š 1750 22nd Ave. S. š Seattle, WA 98144 š Phone 206-322-5474 š Fax 206-322-
5425
8
MN-1316EN
EZ Melt Model EZ18, EZ24, EZ34
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING
Rinsing the filter could cause water to drop
into the kettle. Hot shortening could spatter
and cause serious injury.
d. Put the filter assembly back on the EZ
Melt.
To order replacement filters for your EZ Melt,
call Belshaw.
Belshaw Bros., Inc. š 1750 22nd Ave. S. š Seattle, WA 98144 š Phone 206-322-5474 š Fax 206-322-
5425
EZ Melt Model EZ18, EZ24, EZ34
MN-1316EN
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Cleaning
3
Clean the EZ Melt after every use. Follow these
steps:
WARNING
1. Turn on the heat and the pump.
Thoroughly clean and dry the floor if
shortening, water, or other materials are
spilled. Materials spilled on the floor may
cause serious injury and loss of life.
2. Press the foot pedal to pump shortening out
of the EZ Melt and into a metal container or
fryer kettle.
3. When you cannot pump any more shortening
out of the EZ Melt, release the foot pedal.
Turn off the heat and the pump.
7. Remove the cube melter.
8. Loosen the two fasteners at the back of the
heater head, lift it off the kettle and place it
in a clean safe place. The foot valve and
cord will unsnap from the frame. See Figure
3-1.
4. Disconnect the EZ Melt from the power
source.
5. Allow the shortening in the EZ Melt kettle
to cool to 115“ F/46“ C.
WARNING
Hot shortening can cause serious injury.
6. Clean the EZ Melt filter. Follow these steps:
a. Allow the filter assembly to cool to the
touch.
b. Lift off the filter assembly, holding it by
the frame.
c. Invert the filter assembly over a sink or
garbage can and shake the sediment off
of it.
d. Unsnap the filter to remove it from the
filter frame.
e. Rinse the remaining shortening and
crumbs off of the filter.
Figure 3-1. Removing the Heater Head.
(Place heater head as shown above so no
damage is done to the element.)
Belshaw Bros., Inc. š 1750 22nd Ave. S. š Seattle, WA 98144 š Phone 206-322-5474 š Fax 206-322-
5425
10
MN-1316EN
EZ Melt Model EZ18, EZ24, EZ34
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING
Do not touch the heating element! It is very
hot and will burn you.
11. Remove the kettle from the frame. You
must remove it from the rear.
12. Pour any shortening remaining in the kettle
into a metal container. If it is too heavy or
awkward for you to lift by yourself, get
someone to help you.
WARNING
Thoroughly clean and dry the floor if
shortening, water, or other materials are
spilled. Materials spilled on the floor may
cause serious injury and loss of life.
13. Scrape out any residue and discard it.
14. Wash the kettle, the cube melter, and the
filter frame with warm, soapy water.
15. Dry all the parts completely. The kettle and
all other parts must be completely dry before
you use the EZ Melt again.
WARNING
Moisture on parts causes hot shortening to
spatter, which may cause serious injury.
16. Re-assemble the EZ Melt.
Belshaw Bros., Inc. š 1750 22nd Ave. S. š Seattle, WA 98144 š Phone 206-322-5474 š Fax 206-322-
5425
EZ Melt Model EZ18, EZ24, EZ34
MN-1316EN
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
4
This section is designed as an aid in trouble-
shooting, not as a substitute for a qualified
technician. You may encounter a problem with
your EZ Melt that is not covered in this section,
or you may try the remedies suggested here and
find that they do not correct the problem. In
either case, feel free to call Belshaw Bros. at
(206)322-5474. One of our customer support
representatives will be happy to help you. When
you call, please specify the following:
For factory service, call us for a return goods
authorization. Then send your machine to us,
freight prepaid, with your instructions for
service, your phone number, and the name of the
person for us to contact when we have made a
cost estimate. In most cases, the machine can be
shipped back, freight collect, within five days.
To avoid down time, call us to see whether we
have a machine we can loan to you while your
machine is being serviced.
š The model number of the machine.
š The serial number of the machine.
Ship machines in need of servicing to:
Belshaw Bros., Inc.
1750-22nd Ave. S.
Seattle, WA 98144 USA
š The voltage, phase, and hertz (cycle) of
the machine.
Following is a troubleshooting chart to help you
identify and solve some basic problems.
CAUTION
If you perform repairs yourself or have them
performed by anyone other than Belshaw
Bros. or a service technician authorized by
Belshaw Bros., you do so at your own risk.
WARNING
Disconnect the machine from the power
source before disassembling, repairing, or
wiring.
Belshaw Bros., Inc. š 1750 22nd Ave. S. š Seattle, WA 98144 š Phone 206-322-5474 š Fax 206-322-
5425
12
MN-1316EN
EZ Melt Model EZ18, EZ24, EZ34
Download from Www.Somanuals.com. All Manuals Search And Download.
THE SHORTENING DOES NOT FLOW FREELY THROUGH THE FILTER
SYSTEM
Possible Causes
What To Do
The hose is crimped.
Straighten the hose.
WARNING
To avoid being burned, before doing any of the
following, turn off the EZ Melt and allow the
shortening to cool.
The hose is clogged with shortening.
Soak the hose in warm water to help release the
clogged shortening. Hang it up and let it dry
before you use it again.
The drain tube is clogged with solid shortening.
Remove the drain tube and soak it in warm water
to help release the clogged shortening.
The pickup tube is clogged with residue.
THE PUMP MOTOR WILL NOT RUN
Possible Causes
Remove the pickup tube and clean it.
What To Do
The connection of the power cord to the power
source is faulty.
Make sure the power cord is fully plugged in to a
proper power source.
The circuit breaker has been tripped.
Press the reset button.
If the problem persists, consult your Belshaw
dealer, or call Belshaw.
Belshaw Bros., Inc. š 1750 22nd Ave. S. š Seattle, WA 98144 š Phone 206-322-5474 š Fax 206-322-
5425
EZ Melt Model EZ18, EZ24, EZ34
MN-1316EN
13
Download from Www.Somanuals.com. All Manuals Search And Download.
This page has been left blank intentionally.
Belshaw Bros., Inc. š 1750 22nd Ave. S. š Seattle, WA 98144 š Phone 206-322-5474 š Fax 206-322-
5425
14
MN-1316EN
EZ Melt Model EZ18, EZ24, EZ34
Download from Www.Somanuals.com. All Manuals Search And Download.
5
Parts Lists
The following pages contain current lists of the
parts that make up the EZ18, EZ24, and EZ34
models. Each list refers to an exploded-view
assembly drawing. You can use the parts lists
and assembly drawings as a reference to order
replacement parts.
When ordering replacement parts, please provide
the model number and serial number along with
the correct electrical information about your
equipment. Some of the part numbers vary
according to the voltage, phase, cycle and serial
number of the machine.
IMPORTANT
The parts lists and assembly drawings are
meant as guides. We cannot provide lists and
drawings for every possible configuration of
the EZ Melt models.
Belshaw Bros., Inc. š 1750 22nd Ave. S. š Seattle, WA 98144 š Phone 206-322-5474 š Fax 206-322-
5425
EZ Melt Model EZ18, EZ24, EZ34
MN-1316EN
15
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS LIST 5-1 EZ18-2000 SHORTENING MELTER ASSEMBLY (120V)
BILL OF MATERIAL
ITEM QTY PART NO.
DESCRIPTION
FASTENERS
1
2
3
4
5
6
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
3
1
3
EZ18-0500
EZ18-0502
EZ18-0503
EZ18-0504
EZ24-1000
EZ6-0507
Kettle Frame, WLDT
Kettle, WLDT
ITEM QTY. DESCRIPTION
A
2
¼-20 X ¼
Tek Screw
Filter Holder, WLDT
Cube Melter, Assy.
Motor Enclosure, Assy. (120v)
Tube Assy, Back Supply
Tube Assy, Front Assy.
Rinsing Hose Assy.
Filter Bag
EZ6-0510
7
8
9
SF100-0503
SM100-0002
SM100-0507RH Hose Supply, Assy. RH
SM100-0507LH
SM100-0510
EZ18-0505
EZ18-0011
EZ24-0016
618-0116
Hose Supply, Assy LH
Hose Supply Assy.
Hose Nozzle Assy.
Side Splash Guard
Label: EZ18 Name Plate
Label: Caution; Hot
Data Plate
10
11
12
13
14
0158
990-0651
Wire Holder, ½”
Belshaw Bros., Inc. š 1750 22nd Ave. S. š Seattle, WA 98144 š Phone 206-322-5474 š Fax 206-322-
5425
16
MN-1316EN
EZ Melt Model EZ18, EZ24, EZ34
Download from Www.Somanuals.com. All Manuals Search And Download.
FIGURE 5-1 EZ18-2000 SHORTENING MELTER ASSEMBLY (120V)
Belshaw Bros., Inc. š 1750 22nd Ave. S. š Seattle, WA 98144 š Phone 206-322-5474 š Fax 206-322-
5425
EZ Melt Model EZ18, EZ24, EZ34
MN-1316EN
17
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS LIST 5-2 EZ18-2001 SHORTENING MELTER ASSEMBLY (240V)
BILL OF MATERIAL
ITEM QTY PART NO.
DESCRIPTION
FASTENERS
1
2
3
4
5
6
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
3
1
3
EZ18-0500
EZ18-0502
EZ18-0503
EZ18-0504
EZ24-1001
EZ6-0507
Kettle Frame, WLDT
Kettle, WLDT
ITEM QTY. DESCRIPTION
A
2
¼-20 X ¼
Tek Screw
Filter Holder, WLDT
Cube Melter, Assy.
Motor Enclosure, Assy. (240v)
Tube Assy, Back Supply
Tube Assy, Front Assy.
Rinsing Hose Assy.
Filter Bag
EZ6-0510
7
8
9
SF100-0503
SM100-0002
SM100-0507RH Hose Supply, Assy. RH
SM100-0507LH
SM100-0510
EZ18-0505
EZ18-0011
EZ18-0016
618-0116
Hose Supply, Assy LH
Hose Supply Assy.
Hose Nozzle Assy.
Side Splash Guard
Label: EZ18 Name Plate
Label: Caution; Hot
Data Plate
10
11
12
13
14
0158
990-0651
Wire Holder, ½”
Belshaw Bros., Inc. š 1750 22nd Ave. S. š Seattle, WA 98144 š Phone 206-322-5474 š Fax 206-322-
5425
18
MN-1316EN
EZ Melt Model EZ18, EZ24, EZ34
Download from Www.Somanuals.com. All Manuals Search And Download.
FIGURE 5-2 EZ18-2001 SHORTENING MELTER ASSEMBLY (240V)
Belshaw Bros., Inc. š 1750 22nd Ave. S. š Seattle, WA 98144 š Phone 206-322-5474 š Fax 206-322-
5425
EZ Melt Model EZ18, EZ24, EZ34
MN-1316EN
19
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS LIST 5-3 EZ24-2000 SHORTENING MELTER ASSEMBLY (120V)
BILL OF MATERIAL
ITEM QTY PART NO.
DESCRIPTION
FASTENERS
1
2
3
4
5
6
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
3
1
3
EZ24-0500
EZ24-0502
EZ24-0503
EZ24-0504
EZ24-1000
EZ6-0507
Kettle Frame, WLDT
Kettle, WLDT
ITEM QTY. DESCRIPTION
A
2
¼-20 X ¼
Tek Screw
Filter Holder, WLDT
Cube Melter, Assy.
Motor Enclosure, Assy. (120v)
Tube Assy, Back Supply
Tube Assy, Front Assy.
Rinsing Hose Assy.
Filter Bag
EZ6-0510
7
8
9
SF100-0503
SM100-0002
SM100-0507RH Hose Supply, Assy. RH
SM100-0507LH
SM100-0510
EZ24-0505
EZ24-0017
EZ24-0016
618-0116
Hose Supply, Assy LH
Hose Supply Assy.
Hose Nozzle Assy.
Side Splash Guard
Label: EZ24 Name Plate
Label: Caution; Hot
Data Plate
10
11
12
13
14
0158
990-0651
Wire Holder, ½”
Belshaw Bros., Inc. š 1750 22nd Ave. S. š Seattle, WA 98144 š Phone 206-322-5474 š Fax 206-322-
5425
20
MN-1316EN
EZ Melt Model EZ18, EZ24, EZ34
Download from Www.Somanuals.com. All Manuals Search And Download.
FIGURE 5-3 EZ24-2000 SHORTENING MELTER ASSEMBLY (120V)
Belshaw Bros., Inc. š 1750 22nd Ave. S. š Seattle, WA 98144 š Phone 206-322-5474 š Fax 206-322-
5425
EZ Melt Model EZ18, EZ24, EZ34
MN-1316EN
21
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS LIST 5-4 EZ24-2001 SHORTENING MELTER ASSEMBLY (240V)
BILL OF MATERIAL
ITEM QTY PART NO.
DESCRIPTION
FASTENERS
1
2
3
4
5
6
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
3
1
3
EZ24-0500
EZ24-0502
EZ24-0503
EZ24-0504
EZ24-1001
EZ6-0507
KETTLE FRAME, WLDT
KETTLE, WLDT
ITEM QTY. DESCRIPTION
A
2
¼-20 X ¼
TEK SCREW
FILTER HOLDER, WLDT
CUBE MELTER, ASSY.
MOTOR ENCLOSURE, ASSY. (240V)
TUBE ASSY, BACK SUPPLY
TUBE ASSY, FRONT ASSY.
RINSING HOSE ASSY.
FILTER BAG
EZ6-0510
7
8
9
SF100-0503
SM100-0002
SM100-0507RH HOSE SUPPLY, ASSY. RH
SM100-0507LH
SM100-0510
EZ24-0505
EZ24-0017
EZ24-0016
618-0116
HOSE SUPPLY, ASSY LH
HOSE SUPPLY ASSY.
HOSE NOZEL ASSY.
SIDE SPLASH GUARD
LABEL: EZ24 NAME PLATE
LABEL: CAUTION; HOT
DATA PLATE
10
11
12
13
14
0158
990-0651
WIRE HOLDER, ½”
Belshaw Bros., Inc. š 1750 22nd Ave. S. š Seattle, WA 98144 š Phone 206-322-5474 š Fax 206-322-
5425
22
MN-1316EN
EZ Melt Model EZ18, EZ24, EZ34
Download from Www.Somanuals.com. All Manuals Search And Download.
FIGURE 5-4 EZ24-2001 SHORTENING MELTER ASSEMBLY (240V)
Belshaw Bros., Inc. š 1750 22nd Ave. S. š Seattle, WA 98144 š Phone 206-322-5474 š Fax 206-322-
5425
EZ Melt Model EZ18, EZ24, EZ34
MN-1316EN
23
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS LIST 5-5 EZ34-2000 SHORTENING MELTER ASSEMBLY (120V)
BILL OF MATERIAL
ITEM QTY PART NO.
DESCRIPTION
FASTENERS
1
1
1
1
1
1
1
1
1
1
3
1
3
EZ34-0500
EZ34-0502
EZ34-0503
EZ34-0504
EZ34-1000
EZ34-0505
EZ34-0027
EZ34-0035
EZ34-0036
618-0116
0158
Kettle Frame, WLDT
Kettle, WLDT
ITEM QTY. DESCRIPTION
2
A
2
¼-20 X ¼
Tek Screw
3
Filter Holder, WLDT
Cube Melter, Assy.
Motor Enclosure, Assy. (120v)
Hose Nozzle Assy.
Filter Bag
4
5
6
7
8
Side Splash Guard
Label: EZ34 Name Plate
Label: Caution; Hot
Data Plate
9
10
11
12
990-0651
Wire Holder, ½”
Belshaw Bros., Inc. š 1750 22nd Ave. S. š Seattle, WA 98144 š Phone 206-322-5474 š Fax 206-322-
5425
24
MN-1316EN
EZ Melt Model EZ18, EZ24, EZ34
Download from Www.Somanuals.com. All Manuals Search And Download.
FIGURE 5-5 EZ34-2000 SHORTENING MELTER ASSEMBLY (120V)
Belshaw Bros., Inc. š 1750 22nd Ave. S. š Seattle, WA 98144 š Phone 206-322-5474 š Fax 206-322-
5425
EZ Melt Model EZ18, EZ24, EZ34
MN-1316EN
25
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS LIST 5-6 EZ34-2001 SHORTENING MELTER ASSEMBLY (240V)
BILL OF MATERIAL
ITEM QTY PART NO.
DESCRIPTION
FASTENERS
1
1
1
1
1
1
1
1
1
1
3
1
3
EZ34-0500
EZ34-0502
EZ34-0503
EZ34-0504
EZ34-1001
EZ34-0505
EZ34-0027
EZ34-0035
EZ34-0036
618-0116
0158
Kettle Frame, WLDT
Kettle, WLDT
ITEM QTY. DESCRIPTION
2
A
2
¼-20 X ¼
Tek Screw
3
Filter Holder, WLDT
Cube Melter, Assy.
Motor Enclosure, Assy. (240v)
Hose Nozzle Assy.
Filter Bag
4
5
6
7
8
Side Splash Guard
Label: EZ34 Name Plate
Label: Caution; Hot
Data Plate
9
10
11
12
990-0651
Wire Holder, ½”
Belshaw Bros., Inc. š 1750 22nd Ave. S. š Seattle, WA 98144 š Phone 206-322-5474 š Fax 206-322-
5425
26
MN-1316EN
EZ Melt Model EZ18, EZ24, EZ34
Download from Www.Somanuals.com. All Manuals Search And Download.
FIGURE 5-6 EZ34-2001 SHORTENING MELTER ASSEMBLY (240V)
Belshaw Bros., Inc. š 1750 22nd Ave. S. š Seattle, WA 98144 š Phone 206-322-5474 š Fax 206-322-
5425
EZ Melt Model EZ18, EZ24, EZ34
MN-1316EN
27
Download from Www.Somanuals.com. All Manuals Search And Download.
FIGURE 5-7 EZ24/34-1000 HEATER HEAD ASSEMBLY
Belshaw Bros., Inc. š 1750 22nd Ave. S. š Seattle, WA 98144 š Phone 206-322-5474 š Fax 206-322-
5425
28
MN-1316EN
EZ Melt Model EZ18, EZ24, EZ34
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS LIST 5-7 EZ24/34-1000 HEATER HEAD ASSEMBLY
Belshaw Bros., Inc. š 1750 22nd Ave. S. š Seattle, WA 98144 š Phone 206-322-5474 š Fax 206-322-
5425
EZ Melt Model EZ18, EZ24, EZ34
MN-1316EN
29
Download from Www.Somanuals.com. All Manuals Search And Download.
6
Wiring Diagrams
This section contains the following wiring
diagrams:
EZ18-4002 (120V, 50/60 Hz, 1 Ph)
EZ18-4003 (208/240V, 50/60 Hz, 1 Ph)
Belshaw Bros., Inc. š 1750 22nd Ave. S. š Seattle, WA 98144 š Phone 206-322-5474 š Fax 206-322-
5425
30
MN-1316EN
EZ Melt Model EZ18, EZ24, EZ34
Download from Www.Somanuals.com. All Manuals Search And Download.
Belshaw Bros., Inc. š 1750 22nd Ave. S. š Seattle, WA 98144 š Phone 206-322-5474 š Fax 206-322-
5425
EZ Melt Model EZ18, EZ24, EZ34
MN-1316EN
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Belshaw Bros., Inc. š 1750 22nd Ave. S. š Seattle, WA 98144 š Phone 206-322-5474 š Fax 206-322-
5425
32
MN-1316EN
EZ Melt Model EZ18, EZ24, EZ34
Download from Www.Somanuals.com. All Manuals Search And Download.
|
