Lighthouse
Battery Backup
Download from Www.Somanuals.com. All Manuals Search And Download.
Package Contents
1 – USB Cable
1 – Battery Backup System
1 – Detachable LED Flashlight
1 – Phone-Line Cable
3 – AAA NiMH Batteries
1 – Installation CD containing Belkin
Automatic Shutdown Software
• Incorrect battery connection or replacement
creates risk of explosion.
Safety Information
CAUTION:
• All batteries used are sealed-lead batteries.
Batteries should be recycled.
• Risk of electrical shock—hazardous live
parts inside. The Unit is energized by the
battery supply even when the input AC
power is off.
System Requirements
• Risk of electrical shock—do not open
the case.
The Lighthouse Battery Backup can be used
without the software with any computer using
up to a 17-inch CRT or LCD monitor. You do not
have to have the software installed to utilize the
battery-backup outlets.
• No user-serviceable parts exist inside the
Unit. Refer repair issues only to qualified
personnel. Fuses or other parts must be
replaced ONLY with parts of identical types
and ratings. Substitution of non-identical
parts can cause fire and other
To fully utilize the Unit and its software, your
computer must be running one of the following
®
®
operating systems: Windows 98, Me, NT 4,
2000, 2003, XP, and have a USB port.
safety hazards.
• The Unit is intended for installation and
operation in a controlled environment (a
temperature-controlled, indoor area free of
conductive contaminants).
1
2
Battery-Backup Outlets (Fig. 1)
Surge-Protected-Only Outlets (Fig. 1)
Only data-sensitive equipment such as a
computer, monitor, and external drive should
be plugged into these outlets. Battery power
is automatically provided in case of a power
Plug in equipment such as computer
peripherals, printers, fax machines, or desk
lamps to these outlets.
NOTE: These outlets do not provide battery
outage. Power (AC or battery) is not supplied to power during an outage. The “On/Off” button
these outlets when the Unit is switched off. (Do does not control these outlets.
not plug surge protectors or power strips into
the battery-backup outlets.)
Do not plug surge protectors or power
strips into the battery-backup outlets
Caution: Never connect a laser printer or
scanner to the backup outlets along with
other computer equipment. To do so might
overload the Unit.
(i.e., daisy-chaining).
3
AC Circuit Breaker (Fig. 1)
Should a power overload occur, the circuit
breaker triggers the Unit to turn off AC power.
To restore power, depress the “circuit
breaker” button to reset, then depress the
“Power” button.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
4
USB Communication Port (Fig. 1)
Back Panel (Fig. 1)
The Unit features a USB communication
port. Installation of the cable and the Belkin
Automatic Shutdown Software, which allows
the Unit to connect to your computer, is
optional. The Unit will provide backup power
whether or not the cable and software are
installed; however, without them you will be
unable to utilize the data-management
product features.
1
2
5
Phone/Fax/Modem Surge Protection
(Fig. 1)
The phone/fax/modem lines are
surge-protected. There are one input jack and
two output jacks. This allows you to split one
telephone connection to two separate devices.
3
4
5
1
Top Panel (Fig. 2)
Cord-Management Loop (Fig. 2)
This feature helps to organize and manage the
power cables from your connected equipment.
Route all power cables through the loop for a
clean and organized workspace.
2
The “On/Off” button has four functions:
(Fig. 2)
1
a) Turns on the Unit. Depress button at least
2 seconds. The green indicator lights.
b) Cold-start function. If the battery is charged,
the Unit will work without being plugged into
an outlet. Depress and hold the key for at least
2 seconds to turn on the Unit.
2
3
c) Silence function. During “On Battery Mode”,
the audible sound can be turned on or off by
depressing the switch for less than
1.5 seconds.
d) Battery-test function. During “On-Line
Mode”, depressing the switch for less than
1.5 seconds causes the Unit to perform a
battery test in backup mode.
3
Status Indicators (Fig. 2)
Four LED status lights are located on the
front panel. The status lights indicate specific
conditions of the Unit. (See page 5.)
4
Download from Www.Somanuals.com. All Manuals Search And Download.
LED Indicators and Audible Alarms
AC Power Battery Power
Fault
Replace Battery
The Unit will alarm to indicate certain events.
Low Battery
press and hold
Overload
Front-Panel
Label
Visual
Indicator
Audible Alarm
Description
AC Power
AC Power LED
lights
None
The Unit is operating normally on AC power.
Battery Power
Battery Power
LED lights
Tone every
10 seconds
The Unit is operating on battery power.
The alarm will stop when main AC power
is returned.
Low Battery
Low Battery LED
flashes
Tone every
1 second
The battery energy is running low. This alarm
will continue until the Unit performs a forced
shutdown when the battery is depleted.
Fault
Fault LED lights
Continuous tone
A fault has occurred. Disconnect all
equipment from the Unit prior to checking.
Overload
Overload LED
flashes
Tone every
1 second
The Unit is overloaded. Remove connected
equipment until fault mode is cleared.
Replace Battery
Replace Battery
LED lights
None
The battery has reached the end of its useful
life. The user must replace the battery as
soon as possible to ensure proper operation
of the Unit.
NOTE: The audible alarm will not sound after the alarm is muted.
and type of batteries. Do not attempt to use
alkaline or other non-NiMH battery types
for replacement.
Flashlight
The Unit contains a fully functional, detachable
LED flashlight. The flashlight will automatically
illuminate when the power goes out. This safety
function provides an easy way for you to find the
flashlight while illuminating the area surrounding
the Unit. The LED flashlight may be removed from
the Unit to use as a handheld, portable flashlight.
• Risk of energy hazard. Before replacing
batteries, remove conductive jewelry such as
chains, wristwatches, and rings. High energy
through conductive materials could cause
severe burns.
• Do not short-circuit the batteries.
To remove the LED flashlight from the Unit’s
recharging dock, pull the top of the LED flashlight
out and downward until it disengages. When
not in use, return the LED flashlight to the Unit’s
recharging dock. The LED flashlight will only
fit one way in the recharging dock: with the
flashlight lens pointing toward the top of the Unit
and the LED flashlight button toward the outside.
The LED flashlight will only recharge if properly
docked on the Unit.
• Carefully install the batteries in the LED
flashlight housing, ensuring proper polarity.
Reverse polarity installation may cause
damage. The battery installation polarity is
labeled on the LED flashlight housing.
• Do not heat or incinerate the battery. The
battery may explode.
• Only use the UPS Unit to recharge the
batteries. Charging under other conditions
can cause the battery to leak, overheat, burst,
and/or catch fire.
Flashlight Recharging and Battery Replacement
CAUTION:
• The detachable LED flashlight contains 3
NiMH 700mAh AAA batteries. When replacing
batteries, replace with the same number
• Properly dispose or recycle used batteries.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical Specifications
Capacity
550VA/300W
Battery Overvoltage
Protection
Voltage > 15.0V±0.5V
Input Voltage (Nominal) 120VAC
LED Flashlight
Battery Type
NiMH AAA
1.2V/700mAh* 3 pcs
Input Voltage (Range)
96VAC–135VAC
60Hz
Input Frequency
(Nominal)
LED Flashlight
Recharge Time
(At 25° C) – ≤8 Hours Recover
85% Capacity (After Full
Discharge/Input Voltage
120VAC)
Transfer Time (Typical) ≤10ms (Typical)
Alerts
Visual and Audible
LED Flashlight
Battery Runtime
≥10 hrs @ Full battery charge
& Amb 25° C
Input Breaker
10A/125VAC UL/cUL
Surge Energy
Suppression
700 Joules
(Total Performance Rated
With 10*1000µs Pulse)
Interface/Communication
Efficiency (AC Mode)
Waveform
≥90% (Input Voltage=120VAC;
Switching Load=300W)
Battery Mode
USB Port
Modem Protection Single Line (2 Wire, RJ11)
Jack (In*1; Out*2)
Step Wave
(Pseudo Sine-Wave)
Short-Circuit Protection Shutdown
(AC Mode)
Environment
Short-Circuit Protection Shutdown
(Backup Mode)
Operating Temperature 0° C ~ 35° C
Non-Operating/
15° C ~ 40° C (With Battery)
15° C ~ 50° C
Battery Type
12V/4.5Ah
Storage Temperature
(Without Battery)
Battery Protection
30A/32V Fuse *2 pcs
Operating Humidity
Audible Noise
0 ~ 85% RH (Non-Condensing)
< 42 dBA At 1 Meter
Recharge Time
(At 25° C)
≤16 Hours Recover
85% Capacity (After Full
Loading Discharge /
Input Voltage 120VAC)
Battery Run Time
(90% Full Load)
≥1.0 Minutes
Safety Standards
(At Temperature 25° C)
UL/cUL Meets UL 1778/cUL
EMI Meets FCC Class B
Battery Run Time
(Half Load)
≥6 Minutes
(At Temperature 25° C)
Belkin Tech Support
Belkin B.V.
Boeing Avenue 333
1119 PH Schiphol-Rijk, The Netherlands
+31 (0) 20 654 7300
US: 310-898-1100, ext. 2263
800-223-5546, ext. 2263
UK: 0845 607 77 87
Australia: 1800 235 546
+31 (0) 20 654 7349 fax
New Zealand: 0800 235 546
Belkin Ltd.
4 Pioneer Avenue
Belkin Corporation
501 West Walnut Street
Los Angeles, CA 90220, USA
310-898-1100
Tuggerah Business Park
Tuggerah, NSW 2259, Australia
+61 (0) 2 4350 4600
+61 (0) 2 4350 4700 fax
310-898-1111 fax
© 2006 Belkin Corporation. All rights reserved.
All trade names are registered trademarks of respective
manufacturers listed. Windows and NT are either registered
trademarks or trademarks of Microsoft Corporation in the United
States and/or other countries.
Belkin Ltd.
Express Business Park, Shipton Way
Rushden, NN10 6GL, United Kingdom
+44 (0) 1933 35 2000
+44 (0) 1933 31 2000 fax
P75367
Download from Www.Somanuals.com. All Manuals Search And Download.
Flashlight Controls and Functionality
To turn off the LED flashlight when the light is ON
in any condition:
The LED flashlight will automatically turn on in the
following conditions:
• press the LED flashlight button.
—when the LED flashlight is on the Unit
recharging dock and
NOTE:
• We ship the LED flashlight without the batteries
installed. Carefully install the batteries ensuring
proper polarity, which is labeled on the LED
flashlight housing. After installing the UPS and
turning it on, charge the LED flashlight for at
least 8 hours prior to use.
• the AC power is removed;
• the LED flashlight is removed from the dock;
• the LED flashlight button is pressed.
—when the LED flashlight is removed from the
Unit recharging dock and
• During the initial charge period, the LED
flashlight may not function properly due to low
battery charge.
• the LED flashlight button is pressed
NOTE: For maximum benefit, install the
Unit in an easily accessible location so you
may detach the flashlight for use. Do not
place anything on top of the Unit that may
obscure the control panel or flashlight.
E. Turning off the Unit
Turn off your Battery Backup by pressing and
holding the “On/Off” button for more than
two seconds until the “AC Power” or “Battery
Power” LED goes off. The Unit will beep once.
A. Connect to AC Utility Power
F. To Conduct a Self-Test
Plug in the AC cord to a properly grounded wall Use the self-test to verify both the operation
outlet. Please make sure there are no devices
plugged into the Unit.
of the Unit and the condition of the battery. In
normal utility power, push the “On/Off” button
for less than 1.5 seconds and the Unit will
perform a self-test function. During the
B. Charging the Battery
For best results, charge the battery for eight
hours prior to initial use. The Unit charges
its battery whenever it is connected to the
utility power.
self-test, the Unit operates in backup mode.
NOTE: During the self-test, the Unit briefly
operates on battery-backup power (the
“Battery Power” LED comes on). If the Unit
passes the self-test, it returns to online
operation. If the Unit fails the self-test, it
immediately returns to online operation
and lights the “Replace Battery” LED. The
loads are not affected. Recharge the battery
overnight and perform the self-test again.
If the “Replace Battery” LED is still on, the
battery needs to be replaced.
C. Plug in Power Devices
Plug your devices into the AC outlets on the
top of the Unit. To use the Unit as a master
on/off switch, make sure all of the loads are
switched on.
Caution: Never connect a laser printer or
scanner to the backup outlets along with
other computer equipment. A laser printer
or scanner draws significantly more power
when in use than when idle. This may
overload the Unit.
G. To Silence Audible Alarm
While the Unit is in battery-backup mode, push
the “On/Off” button for less than 1.5 seconds
to silence the audible alarm. (This does not
work if the Unit is in a LOW BATTERY or
OVERLOAD condition.)
D. Turning on the Unit
Turn on your Battery Backup by pressing and
holding the “On/Off” button for longer than two
seconds until the “AC Power” green light comes
on. The Unit will beep once.
All equipment must be powered off prior to
plugging into the Unit (installation).
6
Download from Www.Somanuals.com. All Manuals Search And Download.
H. Connect the Phone/Fax/Modem Lines
Connect a single phone/fax/modem line into
the surge-protected outlets on the back of
the Unit. The RJ11 modular outlet accepts
standard single-line telephone connections.
The connection will require another length of
telephone cable (included).
improperly installed. Make sure that the
telephone line from the wall is plugged into
the connector marked “IN”, and the device to
be protected is plugged into the connector
marked “OUT”.
I. Connect the USB (Universal Serial Port)
Communication Port
NOTE: This connection is optional but highly
recommended as phone/fax/modem lines
often carry dangerous surges and spikes.
The Unit works properly without a
A USB port is provided to relay the signal to
support Windows. To fully utilize the Belkin
Automatic Shutdown software, you will need to
connect the Unit to your computer. Connect the
USB cable to the Unit, then connect the other
end to your computer’s USB port.
phone/fax/modem connection.
CAUTION: The phone/fax/modem protection
feature could be rendered inoperable if
Battery–Replacement Procedure
Caution:
battery to leak, overheat, burst, and/or
catch fire.
• The Unit contains a 12V sealed-lead acid
battery. Replace only with identical battery type, • Properly dispose or recycle used batteries.
as specified on the factory-installed battery.
Replacement requires removing the battery
• Risk of energy hazard. Before replacing
batteries, remove conductive jewelry such as
chains, wristwatches, and rings. High energy
through conductive materials could cause
severe burns.
cover plate on the back of the Unit. No tools are
needed. To replace the batteries:
1. Press fastener to remove the battery cover
plate on the back of the Unit.
2. Disconnect the insulated connectors from the
battery terminals.
• Do not short-circuit the battery.
• Carefully install the batteries in the Unit housing,
ensuring proper polarity. Reverse polarity
installation may cause damage.
3. Remove the battery then insert a new battery
pack, and push the connectors onto the
battery terminals (black-to-black and
• Do not dispose of batteries in a fire. The battery
may explode.
red-to-red). WARNING: Misconnection of the
electrical polarity may result in damage.
• Do not open or mutilate batteries. Released
material is harmful to the skin and eyes.
It may be toxic.
NOTE: There may be a small spark at the
battery terminals when reconnecting the
connectors. This is normal and will not
harm you or the Unit.
• Use the UPS Unit only to recharge the batteries.
Charging under other conditions can cause the 4. Close the battery cover.
occur, and safely shuts down your computer
in your absence. Please be sure to close all
applications prior to installing the software.
Software Installation (Optional)
A) To fully utilize the Battery Backup and its
software, your computer must be able to
operate the following operating systems:
1.To install the software, place the CD into
your computer’s CD-ROM drive.
Windows 98, Me, NT 4, 2000, 2003, or XP,
and have a USB port.
2.Your computer should automatically run
the installation from the CD. If it does not,
click the “Start” icon on the lower, left-
hand corner of your screen, and select
B) Your Battery Backup features the Belkin
Bulldog Plus Software. This protects and
saves your data should a power outage
7
Download from Www.Somanuals.com. All Manuals Search And Download.
“Run” from the menu that appears. Enter
or browse to the CD drive (it may be D).
Next, double-click “setup.exe” to execute
the software. Should you continue to have
Once the “Bulldog Plus Online” screen appears,
choose “Help”. The “Bulldog Online Help”
screen will appear. You may use the Contents,
Index, or Search tabs to assist you with your
a problem, please refer to your computer’s help issues and to get more information on the
owner manual to check the designation for specific features and functions of the software.
your CD-ROM drive.
C)User Manual Installation
3.The “Welcome to the Belkin Bulldog Plus
Product Installation Browser” will appear.
Please click “Install” and select the
Windows version.
You will need Adobe Acrobat Reader to
review the user manuals. If you do not have
download a free version of the software.
4.The “Bulldog Plus Installation” window
will appear. Please choose the appropriate
software to install.
1.From the “Welcome to the Belkin Bulldog
Plus Product Installation Browser” window,
locate and choose “User Manuals”.
5.The InstallShield Wizard will appear
on-screen. Click “Next”.
2.The “Bulldog Plus User Manuals” window
will appear. Please move your pointer to the
manual you wish to open and click on it.
6.Please read the User License Agreement
and click “Yes”.
3.An Adobe PDF file will be opened. To save
a copy to your hard drive, you will need to
go to “File” on your menu bar and choose
“Save a copy”.
7.For “Setup Type”, ALL (Standalone) is
the default. Standalone is for
battery-backup management for your
computer only. Networking management
is for administrators who need to manage
several battery backups in a workstation
environment. Do not install the networking
files unless you are technically qualified to
use these features. For more information
on networking, please refer to the software
user’s manual.
4.In the “Save a Copy” window, please
choose a destination folder for the manual.
D) Uninstall for Windows 98, Me, NT 4, 2000,
2003, XP
There are two options for uninstalling the Belkin
Bulldog Plus Software.
Option 1
8.For “Choose Destination Folder”, you have 1. Click on “Start” in the lower, left-hand corner
the option to choose the location on your
computer for the software. We recommend
using the default option as shown
on-screen. To use the default option,
click “Next”.
of your screen and go to the “Programs”
folder. Scroll to the “Belkin Bulldog Plus”
folder and choose “Setup”. The InstallShield
Wizard will appear.
2. Choose “Remove” and click “Next”.
9.For “Select Program Folder”, you have the
option to choose the program folder for
your software. We recommend using the
default option as shown on-screen. To use
the default option, click “Next”.
3. The “Program Files” and “Audio Files” will
be checked. If they are not, please check
them. Click “Next”. The uninstall procedure
will begin.
4. Click “Finish” when complete.
10.In the “Select Language” screen, please
choose the language you wish to use.
Option 2
(Note: Windows 2000, 2003, and XP users, click
on “Start” and choose “Control Panel”; then go
to step 2.)
11.The software will now be installed. Once
completed, click “Finish”.
NOTE: Please refer to the help feature found
on the “Belkin Bulldog Plus Monitor”. To
access this screen, please click the Belkin
InstallShield Wizard found in the lower,
right-hand corner on your taskbar.
1. Click on “Start” in the lower, left-hand corner
of your screen, go to “Settings”, and choose
“Control Panel”.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
2. In Control Panel, locate and click on the
“Add/Remove Programs” icon. The
“Add/Remove Programs” window will appear.
4. Choose “Remove” and click “Next”.
5. “Program Files” and “Audio Files” will be
checked. If they are not, please check them.
Click “Next”. The uninstall procedure
will begin.
3. Locate and select the Belkin Bulldog Plus
Software. Click the “Change/Remove” button
on the right. InstallShield Wizard will appear.
6. Click “Finish” when complete.
Troubleshooting
PROBLEM
POSSIBLE CAUSE
SOLUTION
Flashlight does not
turn on or operates
abnormally
Flashlight batteries not
fully charged
Return the LED flashlight to the Unit
charging dock and charge for at least
8 hours.
Flashlight does not
charge—Unit charging
dock not functioning
1. Make sure the UPS Unit is plugged in
and turned on.
2. Clean off the 2 metal contacts on the
flashlight and the Unit charging dock
using a dry, lint-free cotton cloth. Do not
use any liquid to clean these surfaces.
3. If the LED flashlight does not appear
to recharge after cleaning the contacts,
replace the rechargeable NiMH batteries
using identical replacement batteries.
Unit not on, LED not lit “On/Off” button not
pushed or pushed less
Press the “On/Off” button for more than
2 seconds
than 2 seconds
Battery voltage is too
low
Recharge the Unit at least 8 hours
UPS fault
Contact service personnel
(1-800-2 BELKIN)
Unit always on battery
mode
Power cord loose
Re-plug the power cord
AC breaker is burned
out or tripped
Replace or reset the breaker
AC utility voltage is
too high or too low, or
there is a blackout
Normal condition
Backup time too short
Battery not fully
charged
Recharge the Unit at least 8 hours
The Unit is on overload Remove some unnecessary loads
Charger fault or other
reason
Replace battery;
The Unit continuously
beeps
Overload
Disconnect non-critical devices
Red LED lit
Battery failure
Replace battery;
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Belkin Corporation (“Belkin”) thanks you for
choosing one of our products. This User
License Agreement (“Agreement”) contains the
terms and conditions under which limited use of
the product is licensed to you.
upon such termination you will immediately
destroy all programs and documentation,
including all copies made or obtained by you.
SOFTWARE, PROGRAM, DOCUMENTATION,
AND ANY RELATED INFORMATION, GOODS
OR SERVICES ARE PROVIDED WITH NO
WARRANTY OR REPRESENTATION OF
ANY KIND WHATSOEVER. BELKIN HEREBY
DISCLAIMS ALL OTHER WARRANTIES,
EXPRESSED OR IMPLIED, INCLUDING BUT
PLEASE READ THIS NOTICE CAREFULLY.
DO NOT USE THE SOFTWARE OR PRODUCT
UNTIL YOU HAVE READ AND AGREED
TO THIS AGREEMENT. IF YOU USE THE
SOFTWARE AND PRODUCT, YOU ARE
AGREEING TO THE TERMS AND CONDITIONS NOT LIMITED TO THE IMPLIED WARRANTIES
SET OUT IN THIS AGREEMENT. IF YOU
DO NOT ACCEPT THESE TERMS AND
CONDITIONS, YOU MUST RETURN THE
UNOPENED PRODUCT WITH THE DISKS
INSIDE TO THE PARTY FROM WHOM YOU
RECEIVED IT.
OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE.
The entire risk of the use, results and
performance of the software, program and
documentation is borne by you. Should any
or all of the product, software, program,
documentation, or related information, goods
or services be defective, misused, unsuitable
or cause or give rise to any harm or liability
whatsoever, you, not Belkin or its associates,
dealers or agents, assume the entire liability,
cost of repair, correction or any payment or
other remedy whatsoever. Furthermore, no
warranty or guarantee is made regarding the
use or results of the product, software, program,
documentation, or any related information,
goods or services in terms of correctness,
accuracy, reliability, timeliness or otherwise. You
use and rely on the program at your own risk.
The following is the only and exclusive warranty
and remedy of any kind: Belkin does warrant
that the program disks are free from physical
defects in materials and workmanship under
normal use for a period of one (1) year from
the date of purchase, as evidenced by a copy
of the sales receipt. Return the defective disk
or documentation with your receipt directly to
Belkin for a replacement.
SCOPE OF USE: In this Agreement,
software means all machine-readable software
programs and associated files in this package,
all modified versions of and upgrades or
improvements to such programs and all copies
of such programs and files. You, a single user
opening this envelope, may use the software
on a single central processing unit. You may
not rent it, loan it out, or lease it, nor use it on a
multiuser system.
LICENSE: You have the non-exclusive right
to use the software. You are not permitted
to copy, modify or transfer the software
or documentation. You may not compile,
disassemble or otherwise reverse engineer,
breakdown, analyze or modify the software.
USE AND RESTRICTIONS: You are
permitted to make backup copies of all the
software disks for archival purposes only.
You must reproduce the proprietary notice
set forth on the disks and affix them to all
backup copies. You are not permitted to use
these programs in connection with a computer
service, or to use the backup copies other than
as a replacement for the original copy.
DISCLAIMER: Belkin or its associates will
in no event be liable (i) in any amount for
lost profits or special, incidental, punitive or
consequential damages, or (ii) for any claim
or damage of any nature, or under any theory,
whatsoever, in any amount in excess of the
purchase price you paid for the product. The
warranties and remedies here set forth are
exclusive, and in lieu of all others oral or written,
expressed or implied. Some jurisdictions do
not allow exclusion or limitation of implied
warranties or of liability for incidental damages,
so the foregoing limitations or exclusion may
TERM: This license is effective upon
acceptance by opening this envelope or in
any other way using the enclosed software,
which will constitute your acceptance of, and
agreement to, this Agreement, and is effective
until terminated. The limited license in this
Agreement will be automatically terminated if
you fail to comply with any of the Terms and
conditions in this Agreement. You agree that
10
Download from Www.Somanuals.com. All Manuals Search And Download.
not apply to you. This warranty gives you
statement of agreement between yourself and
specific legal rights, which vary from jurisdiction Belkin and supersedes any prior agreements,
to jurisdiction.
oral or written, and any other communications
relating to the subject matter of this Agreement.
HOWEVER, YOU WAIVE SUCH RIGHTS,
EXCEPT AS EXPRESSLY PROVIDED UNDER
THE TERMS AND CONDITIONS OF THIS
AGREEMENT, TO THE MAXIMUM EXTENT
ALLOWED BY LAW.
SEVERABILITY:
Any term or provision of this Agreement or any
application thereof, which may be prohibited or
unenforceable by law in a particular jurisdiction,
shall be interpreted and enforced to the
maximum extent allowed in such jurisdiction
(which the parties acknowledge could mean
severing the provision from this Agreement or, if
allowed, enforcing it in a narrower form), without
affecting the remainder of this Agreement, or
any other application of such term or provision
in such jurisdiction, or application of such term
or provision in any jurisdiction.
The license is governed by the laws prevailing
in the State of New York, without regard to its
conflicts of laws principles.
ACKNOWLEDGMENT:
By opening the package on which this
Agreement is printed, or through which it is
visible, you acknowledge that you have read
this Agreement, understand it, and agree that
this Agreement is the complete and exclusive
Storage
Store the Unit covered and upright in a cool,
dry location with its battery fully charged.
Before storing, charge the Unit’s battery for
at least six (6) hours. Disconnect any cables
connected to the computer interface port to
avoid unnecessary drainage of the battery.
Extended Storage
During extended storage in environments where
the ambient temperature is +5º F to +86º F,
charge the Unit’s battery every six (6) months.
During extended storage in environments where
the ambient temperature is +86º F to +113º F,
charge the Unit’s battery every three (3) months.
Note—Store the Unit:
Away from sunlight
•
Away from heat
•
Away from water
Recycling Information
Your Battery Backup contains a non-spillable, sealed-lead battery. On the battery, you will find the
battery name. Please reference the chart below for recycling information.
Battery Name Recycling Inside the USA
Recycling Outside the USA
BB Battery
(800) 278-8599
(800) 738-7372
N/A
CSB Battery
1 (817) 244-4415
VISION Battery (604) 730-2877
Ritar Battery (888) 841-5179
N/A
N/A
11
Download from Www.Somanuals.com. All Manuals Search And Download.
|