WMP 511W
WMP 511S
Washing Machine
User's Manual
Document Number
2820523557 / 05-06-13.(10:03)
Download from Www.Somanuals.com. All Manuals Search And Download.
1.6 Compliance with the WEEE Directive
and Disposing of the Waste Product:
This product complies with EU WEEE Directive
(2012/19/EU). This product bears a classification
symbol for waste electrical and electronic
equipment (WEEE).
This product has been manufactured with high
quality parts and materials which can be reused
and are suitable for recycling. Do not dispose of
the waste product with normal domestic and other wastes at
the end of its service life. Take it to the collection center for
the recycling of electrical and electronic equipment. Please
consult your local authorities to learn about these collection
centers.
2.3 Removing the transportation locks
A WARNING
Do not remove the transportation locks before taking out the
packaging reinforcement.
Remove the transportation safety bolts before operating the
washing machine! Otherwise, the product will be damaged.
2 Installation
Refer to the nearest Authorised Service Agent for installation
of the product. To make the product ready for use, review
the information in the user manual and make sure that the
electricity, tap water supply and water drainage systems are
appropriate before calling the Authorized Service Agent. If they
are not, call a qualified technician and plumber to have any
necessary arrangements carried out.
Loosen all the bolts with a suitable spanner until they rotate
freely (C). Remove transportation safety bolts by turning them
gently. Attach the plastic covers supplied in the User Manual
bag into the holes on the rear panel. (P)
INFORMATIONS
C
Preparation of the location and electrical, tap water and waste
water installations at the place of installation is under customer’s
responsibility.
INFORMATIONS
Keep the transportation safety bolts in a safe place to reuse when
the washing machine needs to be moved again in the future.
C
Make sure that the water inlet and discharge hoses as well as the
power cable are not folded, pinched or crushed while pushing the
product into its place after installation or cleaning procedures.
Never move the product without the transportation safety bolts
properly fixed in place!
B WARNING
Installation and electrical connections of the product must be
carried out by the Authorized Service Agent. Manufacturer shall not
be held liable for damages that may arise from procedures carried
out by unauthorized persons.
2.4 Connecting water supply
INFORMATIONS
C
The water supply pressure required to run the product is between
1 to 10 bars (0.1 – 1 MPa). It is necessary to have 10 – 80 liters
of water flowing from the fully open tap in one minute to have your
machine run smoothly. Attach a pressure reducing valve if water
pressure is higher.
A WARNING
Prior to installation, visually check if the product has any defects on
it. If so, do not have it installed. Damaged products cause risks for
your safety.
If you are going to use the double water-inlet product as a single
(cold) water-inlet unit, you must install the supplied stopper to
the hot water valve before operating the product. (Applies for the
products supplied with a blind stopper group.)
2.1 Appropriate installation location
• Place the machine on a rigid floor. Do not place it on a long
pile rug or similar surfaces.
If you want to use both water inlets of the product, connect the
hot water hose after removing the stopper and gasket group from
the hot water valve. (Applies for the products supplied with a blind
stopper group.)
• Total weight of the washing machine and the dryer -with
full load- when they are placed on top of each other
reaches to approx. 180 kilograms. Place the product on a
solid and flat floor that has sufficient load carrying capacity!
• Do not place the product on the power cable.
• Do not install the product at places where temperature may
fall below 0ºC.
A WARNING
Models with a single water inlet should not be connected to the
hot water tap. In such a case the laundry will get damaged or the
product will switch to protection mode and will not operate.
• Place the product at least 1 cm away from the edges of
other furniture.
Do not use old or used water inlet hoses on the new product. It may
2.2 Removing packaging reinforcement
Tilt the machine backwards to remove the packaging
reinforcement. Remove the packaging reinforcement by
pulling the ribbon.
cause stains on your laundry.
Connect the special hoses supplied with the product to the
water inlets on the product. Red hose (left) (max. 90 ºC) is for
hot water inlet, blue hose (right) (max. 25 ºC) is for cold water
inlet.
Download from Www.Somanuals.com. All Manuals Search And Download.
Washing Machine / User’s Manual
3 / EN
again by hand.
A WARNING
Ensure that the cold and hot water connections are made correctly
when installing the product. Otherwise, your laundry will come out
hot at the end of the washing process and wear out.
Tighten all hose nuts by hand. Never use a wrench when
tightening the nuts. Open the taps completely after making the
hose connection to check for water leaks at the connection
points. If any leaks occur, turn off the tap and remove the nut.
Retighten the nut carefully after checking the seal. To prevent
water leakages and damages caused by them, keep the taps
closed when the machine is not in use.
A WARNING
Do not use any tools to loosen the lock nuts. Otherwise, they will
get damaged.
2.7 Electrical connection
Connect the product to a grounded outlet protected by a 13
A fuse. Our company shall not be liable for any damages
that will arise when the product is used without grounding in
accordance with the local regulations.
2.5 Connecting to the drain
• The end of the drain hose must be directly connected to
the wastewater drain or to the washbasin.
• Connection must comply with national regulations.
• Power cable plug must be within easy reach after
installation.
• If the current value of the fuse or breaker in the house is
less than 13 Amps, have a qualified electrician install a 13
Amp fuse.
A WARNING
Do not remove the transportation locks before taking out the
packaging reinforcement.
• The voltage specified in the “Technical specifications”
section must be equal to your mains voltage.
• Do not make connections via extension cables or multi-
plugs.
• The hose should be attached to a height of at least 40 cm,
and 100 cm at most.
• In case the hose is elevated after laying it on the floor level
or close to the ground (less than 40 cm above the ground),
water discharge becomes more difficult and the laundry
may come out excessively wet. Therefore, follow the
heights described in the figure.
WARNING: Damaged power cables must be
replaced by the Authorized Service Agents.
B
Electrical requirements
Before you insert the plug into the wall socket make sure
that the voltage and the frequency shown in the rating label
corresponds to your electricity supply.
We recommend that this appliance be connected to the mains
supply via a suitable switched and fused socket in a readily
accessible position.
Should the mains lead of the appliance become damaged or
need replacing at any time, it must be replaced by a special
purpose made mains lead which can only be obtained from a
Authorised Service Agent.
• To prevent flowing of dirty water back into the machine and
to allow for easy discharge, do not immerse the hose end
into the dirty water or do not drive it in the drain more than
15 cm. If it is too long, cut it short.
• The end of the hose should not be bent, it should not be
stepped on and the hose must not be pinched between the
drain and the machine.
• If the length of the hose is too short, use it by adding
an original extension hose. Length of the hose may not
be longer than 3.2 m. To avoid water leak failures, the
connection between the extension hose and the drain
hose of the product must be fitted well with an appropriate
clamp as not to come off and leak.
WARNING: This appliance must be earthed
B
If the fitted moulded plug is not suitable for your socket, then
the plug should be cut off and an appropriate plug fitted.
Destroy the old plug, which is cut off as a plug with a bared
cord could cause a shock hazard if inserted into a socket
elsewhere in the house.
The moulded plug on this appliance incorporates a 13A
fuse. Should the fuse need to be replaced an ASTA approved
BS1362 fuse of the same rating must be used. Do not forget
to refit the fuse cover. In the event of losing the fuse cover,
the plug must not be used until a replacement fuse cover has
been fitted. Colour of the replacement fuse cover must be the
same colour as that visible on the pin face of the plug. Fuse
covers are available from any good electrical store.
2.6 Adjusting the feet
A WARNING
In order to ensure that the product operates more silently and
vibration-free, it must stand level and balanced on its feet. Balance
the machine by adjusting the feet. Otherwise, the product may
move from its place and cause crushing and vibration problems.
Loosen the lock nuts on the feet by hand. Adjust the feet until
the product stands level and balanced. Tighten all lock nuts
Download from Www.Somanuals.com. All Manuals Search And Download.
Washing Machine / User’s Manual
4 / EN
Important
INFORMATIONS
Use an anti-limescale suitable for the washing machines.
C
Fitting a different plug
As the colours of the wires in the mains lead of this appliance
may not correspond with the coloured markings identifying
the terminals on your plug, proceed as follows:
1 Connect the green - yellow or green (earth) wire to the
terminal in the plug marked ‘E’ or with the symbol f or
coloured green and yellow or green.
2 Connect the blue (neutral) wire to the terminal in the plug
marked ‘N’ or coloured black.
3 Connect the brown (live) wire to the terminal in the plug
marked ‘L’ or coloured red.
Some water might have remained in the product due to the quality
control processes in the production. It is not harmful for the product.
2.9 Disposing of packaging material
Packaging materials are dangerous to children. Keep
packaging materials in a safe place away from reach of the
children.
Packaging materials of the product are manufactured from
recyclable materials. Dispose of them properly and sort in
accordance with recycled waste instructions. Do not dispose
of them with normal domestic waste.
With the alternative plugs a 13A fuse must be fitted either
in the plug or adaptor or in the main fuse box. If in doubt
contact a qualified electrician.
2.10 Transportation of the product
Unplug the product before transporting it. Remove water drain
and water supply connections. Drain the remaining water in
the product completely; see, "Draining remaining water and
cleaning the pump filter". Install transportation safety bolts in
the reverse order of removal procedure; see, "Removing the
transportation locks".
INFORMATIONS
Never move the product without the transportation safety bolts
properly fixed in place!
C
2.11 Disposing of the old product
Dispose of the old product in an environmentally friendly
manner.
Refer to your local dealer or solid waste collection centre in
your area to learn how to dispose of your product.
For children's safety, cut the power cable and break the
locking mechanism of the loading door so that it will be
nonfunctional before disposing of the product.
Transportation of the product
1. Unplug the product before transporting it.
2. Remove water drain and water supply connections.
3. Drain all water that has remained in the product. See 7.5
4. Install transportation safety bolts in the reverse order of
removal procedure; see 3.3.
3 Preparation
3.1 Things to be done for energy saving
Following information will help you use the product in an
ecological and energy-efficient manner.
• Operate the product in the highest capacity allowed by the
programme you have selected, but do not overload; see,
"Programme and consumption table".
Never move the product without the transportation
C
safety bolts properly fixed in place!
• Always follow the instructions on the detergent packaging.
• Wash slightly soiled laundry at low temperatures.
• Use faster programmes for small quantities of lightly soiled
laundry.
WARNING: Packaging materials are dangerous to
children. Keep packaging materials in a safe place
A
away from reach of the children.
• Do not use high temperatures for laundry that is not heavily
soiled or stained.
2.8 First use
• Do not use detergent in excess of the amount
recommended on the detergent package.
Before starting to use the product, make sure that all
preparations are made in accordance with the instructions in
sections "Important safety instructions" and "Installation".
To prepare the product for washing laundry, perform first
operation in Cotton-90 programme. Before starting the
programme, put max. 100 g of powder anti-limescale into
the main wash detergent compartment (compartment nr. II).
If the anti-limescale is in tablet form, put only one tablet into
compartment nr. II. Dry the inside of the bellow with a clean
piece of cloth after the programme has come to an end.
3.2 Sorting the laundry
• Sort laundry according to type of fabric, colour, and degree
of soiling and allowable water temperature.
• Always obey the instructions given on the garment tags.
3.3 Preparing laundry for washing
• Laundry items with metal attachments such as, underwired
bras, belt buckles or metal buttons will damage the
machine. Remove the metal pieces or wash the clothes by
putting them in a laundry bag or pillow case.
Download from Www.Somanuals.com. All Manuals Search And Download.
Washing Machine / User’s Manual
5 / EN
• Take out all substances in the pockets such as coins, pens
and paper clips, and turn pockets inside out and brush.
Such objects may damage the product or cause noise
problem.
A WARNING
In case of misplacing the laundry, noise and vibration problems may
occur in the machine.
• Put small size clothes such as infant's socks and nylon
stockings in a laundry bag or pillow case.
3.6 Using detergent and softener
• Place curtains in without compressing them. Remove
curtain attachment items.
• Fasten zippers, sew loose buttons and mend rips and
tears.
• Wash “machine washable” or “hand washable” labeled
products only with an appropriate programme.
• Do not wash colours and whites together. New, dark
coloured cottons release a lot of dye. Wash them
separately.
• Tough stains must be treated properly before washing. If
unsure, check with a dry cleaner.
Detergent Drawer
The detergent drawer is composed of three compartments:
- (1) for prewash
- (2) for main wash
– (3) for softener
– (*) in addition, there is siphon piece in the softener
compartment.
3
1
2
• Use only dyes/colour changers and limescale removers
suitable for machine wash. Always follow the instructions
on the package.
• Wash trousers and delicate laundry turned inside out.
• Keep laundry items made of Angora wool in the freezer for
a few hours before washing. This will reduce pilling.
• Laundry that are subjected to materials such as flour, lime
dust, milk powder, etc. intensely must be shaken off before
placing into the machine. Such dusts and powders on the
laundry may build up on the inner parts of the machine in
time and can cause damage.
Detergent, softener and other cleaning agents
• Add detergent and softener before starting the washing
programme.
• Never open the detergent drawer while the washing
programme is running!
• When using a programme without prewash, do not put any
detergent into the prewash compartment (compartment nr.
1).
• In a programme with prewash, do not put liquid detergent
into the prewash compartment (compartment nr. 1).
• Do not select a programme with prewash if you are using a
detergent bag or dispensing ball. Place the detergent bag
or the dispensing ball directly among the laundry in the
machine.
3.4 Correct load capacity
The maximum load capacity depends on the type of laundry,
the degree of soiling and the washing programme desired.
The machine automatically adjusts the amount of water
according to the weight of the loaded laundry.
A WARNING
Follow the information in the “Programme and consumption table”.
When overloaded, machine’s washing performance will drop.
Moreover, noise and vibration problems may occur.
• If you are using liquid detergent, do not forget to place
the liquid detergent cup into the main wash compartment
(compartment nr. 2).
3.7 Choosing the detergent type
Laundry types and their average weights in the following table
are given as examples.
The type of detergent to be used depends on the type and
colour of the fabric.
Laundry type
Weight (g)
• Use different detergents for coloured and white laundry.
• Wash your delicate clothes only with special detergents
(liquid detergent, wool shampoo, etc.) used solely for
delicate clothes.
• When washing dark coloured clothes and quilts, it is
recommended to use liquid detergent.
• Wash woolens with special detergent made specifically for
woolens.
Bathrobe
Duvet cover
Bed Sheet
Pillowcase
Tablecloth
Towel
1200
700
500
200
250
200
200
Men’s shirt
A WARNING
Use only detergents manufactured specifically for automatic
3.5 Loading the laundry
Open the loading door. Place laundry items loosely into the
machine. Push the loading door to close until you hear a
locking sound. Ensure that no items are caught in the door.
washing machines.
Do not use soap powder.
INFORMATIONS
The loading door is locked while a programme is running. The door
can only be opened a while after the programme comes to an end.
C
Download from Www.Somanuals.com. All Manuals Search And Download.
Washing Machine / User’s Manual
6 / EN
Using bleaches
3.8 Adjusting detergent amount
• Select a programme with prewash and add the bleaching
agent at the beginning of the prewash. Do not put
detergent in the prewash compartment.
• Do not use bleaching agent and detergent by mixing them.
• Use just a little amount (approx. 50 ml) of bleaching agent
and rinse the clothes very well as it causes skin irritation.
Do not pour the bleaching agent onto the clothes and do
not use it for coloured clothes.
The amount of washing detergent to be used depends on the
amount of laundry, the degree of soiling and water hardness.
Read the manufacturer's instructions on the detergent
package carefully and follow the dosage values.
• Do not use amounts exceeding the dosage quantities
recommended on the detergent package to avoid problems
of excessive foam, poor rinsing, financial savings and
finally, environmental protection.
• When using oxygen based bleaches, follow the instructions
on the package and select a programme that washes at a
lower temperature.
• Use lesser detergent for small amounts or lightly soiled
clothes.
• Use concentrated detergents in the recommended dosage.
• Oxygen based bleaches can be used together with
detergents; however, if its thickness is not the same with
the detergent, put the detergent first into the compartment
nr. "II" in the detergent drawer and wait until the detergent
flows while the machine is taking in water. Add the
bleaching agent from the same compartment while the
machine is still taking in water.
3.9 Using softeners
Pour the softener into the softener compartment of the
detergent drawer.
• Use the dosages recommended on the package.
• Do not exceed the (>max<) level marking in the softener
compartment.
• If the softener has lost its fluidity, dilute it with water before
putting it in the detergent drawer.
Using limescale remover
• When required, use limescale removers manufactured
specifically for washing machines only.
• Always follow instructions on the package.
3.10 Tips for efficient washing
Clothes
Delicates/
Woolens/Silks
Light colours and whites
Colours
Dark colours
(Recommended
(Recommended
temperature range
based on soiling level:
cold-30ºC)
(Recommended temperature
range based on soiling level:
40-90ºC)
(Recommended temperature
range based on soiling level:
cold-40ºC)
temperature range
based on soiling level:
cold-40ºC)
It may be necessary to pre-treat Powder and liquid
the stains or perform prewash. detergents recommended
Powder and liquid detergents
for colours can be used at
Liquid detergents
Prefer liquid detergents
produced for delicate
clothes. Woolen and
silk clothes must be
washed with special
woolen detergents.
Heavily Soiled
recommended for whites can be dosages recommended for
used at dosages recommended heavily soiled clothes. It is
suitable for colours
and dark colours can
(difficult stains such
as grass, coffee,
fruits and blood.)
for heavily soiled clothes. It is
recommended to use powder be used at dosages
recommended to use powder
detergents to clean clay and recommended for
detergents to clean clay and soil soil stains and the stains that heavily soiled clothes.
stains and the stains that are
sensitive to bleaches.
are sensitive to bleaches. Use
detergents without bleach.
Powder and liquid detergents Liquid detergents
Prefer liquid detergents
produced for delicate
clothes. Woolen and
silk clothes must be
washed with special
Normally Soiled
Powder and liquid detergents
recommended for colours
suitable for colours
and dark colours can
be used at dosages
recommended for whites can be can be used at dosages
(For example, stains
caused by body on
collars and cuffs)
used at dosages recommended recommended for normally
for normally soiled clothes.
soiled clothes. Use detergents recommended for
without bleach.
normally soiled clothes. woolen detergents.
Powder and liquid detergents Liquid detergents
Prefer liquid detergents
produced for delicate
clothes. Woolen and
silk clothes must be
Powder and liquid detergents
recommended for colours
suitable for colours
and dark colours can
be used at dosages
Lightly Soiled
recommended for whites can be can be used at dosages
used at dosages recommended recommended for lightly
(No visible stains
exist.)
for lightly soiled clothes.
soiled clothes. Use detergents recommended for lightly washed with special
without bleach. soiled clothes. woolen detergents.
Download from Www.Somanuals.com. All Manuals Search And Download.
Washing Machine / User’s Manual
7 / EN
4 Operating the product
4.1 Control panel
1
1 - Programme Selection knob
(Uppermost position On / Off)
2 - Door open indicator
2
3
3 - Programme Follow-up indicator
4 - Start / Pause button
4
5
5 - Spin Speed Adjustment button
• Synthetics
4.2 Preparing the machine
Make sure that the hoses are connected tightly. Plug in your
machine. Turn the tap on completely. Place the laundry in the
machine. Add detergent and fabric softener.
Use this programme to wash your synthetic clothes (shirts,
blouses, synthetic/cotton blends, etc.). It washes with a gentle
action and has a shorter washing cycle compared to the
Cotton programme.
For curtains and tulle, use the Synthetic 40˚C programme.
As their meshed texture causes excessive foaming, wash the
veils/tulle by putting little amount of detergent into the main
wash compartment. Do not put detergent in the prewash
compartment.
Programme selection
Select the programme suitable for the type, quantity
and soiling degree of the laundry in accordance with the
"Programme and consumption table" and the temperature
table below. Select the desired programme with the
Programme Selection button.
• Woollens
Use this programme to wash your woolen clothes. Select
the appropriate temperature complying with the tags of your
clothes. Use appropriate detergents for woolens.
Heavily soiled white cottons and linens. (coffee
90˚C
table covers, tableclothes, towels, bed sheets,
etc.)
4.4 Additional programmes
For special cases, additional programmes are available in the
Normally soiled, coloured, fade proof linens,
cottons or synthetic clothes (shirt, nightgown,
pajamas, etc.) and lightly soiled white linens
(underwear, etc.)
machine.
60˚C
INFORMATIONS
Additional programmes may differ according to the model of the
machine.
C
40˚C-
30˚C-
Cold
Blended laundry including delicate textile (veil
curtains, etc.), synthetics and woolens.
• Cottons Eco
Use this programme to wash your laundry washable in
cottons programme for a longer time, still with a very good
performance for saving purposes.
INFORMATIONS
C
Use an anti-limesc Programmes are limited with the highest spin
speed appropriate for that particular type of fabric. ale suitable for
the washing machines.
INFORMATIONS
Cottons Eco programme consumes less energy compared to other
cottons programmes.
C
When selecting a programme, always consider the type of fabric,
colour, degree of soiling and permissible water temperature.
• Delicates
For further programme details, see “Programme and consumption
table”.
Use this programme to wash your delicate clothes. It washes
with a gentle action without any interim spin compared to the
Synthetics programme.
4.3 Main programmes
• Hand wash
Depending on the type of fabric, use the following main
programmes.
Use this programme to wash your woolen/delicate clothes
that bear “not machine- washable” tags and for which hand
wash is recommended. It washes laundry with a very gentle
washing action to not to damage clothes.
• Mini 30
• Cottons
Use this programme for your cotton laundry (such as bed
sheets, duvet and pillowcase sets, towels, bathrobes,
underwear, etc.). Your laundry will be washed with vigorous
washing action for a longer washing cycle.
Use this programme to wash your lightly soiled cotton clothes
in a short time.
Download from Www.Somanuals.com. All Manuals Search And Download.
Washing Machine / User’s Manual
8 / EN
• Cottons with Prewash
Prefer this programme only for heavily soiled cotton clothes.
INFORMATIONS
Not using this programme with prewash will save energy, water,
detergent and time.
C
4.5 Special programmes
For specific applications, select any of the following
programmes.
• Rinse
Use this programme when you want to rinse or starch
separately.
• Spin + Drain
Use this programme to apply an additional spin cycle for your
laundry or to drain the water in the machine.
INFORMATIONS
C
If you wish to drain the water only without spinning your laundry,
select the Spin+Pump programme and press “Start / Pause”
button. Machine will switch to spin step once it completes the
program step. Press “Start / Pause” button to stop the machine as
soon as you see the drum rotating. And cancel this programme by
turning Programme Selection knob to any other position.
Download from Www.Somanuals.com. All Manuals Search And Download.
Washing Machine / User’s Manual
9 / EN
4.6 Programme and consumption table
EN
2
Programme
Cottons
90
60
5
5
130
115
120
120
145
145
116
113
105
66
53
64
50
52
45
38
38
55
54
52
47
50
34
72
1.63
1.10
0.97
0.10
0.80
0.75
0.65
1.02
0.50
0.10
0.26
0.35
0.20
0.21
1400
1400
1400
1400
1400
1400
1400
800
Cottons with Prewash
Cottons
40
5
Cottons
Cold
60**
60**
40**
60
5
Cottons Eco
Cottons Eco
Cottons Eco
Synthetics
Synthetics
Synthetics
Delicates
5
2.5
2.5
2.5
2.5
2.5
2
40
800
Cold
30
800
61
800
Woollens
40
1.5
1
54
800
Hand Wash
Mini
20
41
800
30
2.5
29
1400
• : Selectable
** : Energy Label programme (EN 60456 Ed. 3)
***: If maximum spin speed of the machine is lower then this value, you can only select up to the maximum spin speed.
INFORMATIONS
C
Water and power consumption may vary subject to the changes in water pressure, water hardness and temperature, ambient temperature, type
and amount of laundry, selection of auxiliary functions and spin speed, and changes in electric voltage.
** “Cotton Economic 40°C and Cotton Economic 60°C are standard cycles.” These cycles are known as ‘40°C
cotton standard cycle’ and ‘60°C cotton standard cycle’ and indicated with the
panel.
symbols on the
Download from Www.Somanuals.com. All Manuals Search And Download.
Washing Machine / User’s Manual
10 / EN
4.7 Starting the programme
Press Start / Pause button to start the programme.
Programme follow-up light showing the startup of the
programme will turn on.
INFORMATIONS
If you start a new programme after cancelling the previous one,
this new programme will start without draining the water in the
machine.
C
Progress of programme
If you must certainly open the loading door when the “Door
Open” light is off, you need to use “Spin+Pump” programme. See
“Spin+Pump”
Progress of a running programme can be followed from the
Programme Follow-up indicator with the lights "Running" and
"End/Cancel".
Re-spinning the laundry
Unbalanced load control system can prevent spinning
because of unbalanced load of laundry in the machine. If you
would like to spin again:
INFORMATIONS
C
If the machine does not pass to the spinning step, automatic
unbalanced load detection system might have been activated due to
the unbalanced distribution of the laundry in the machine.
Rearrange the laundry in the machine. Select Spin+Pump
programme and press “Start / Pause" button.
4.8 Loading door lock
There is a locking system on the loading door of the machine
that prevents opening of the door in cases when the water
level is unsuitable.
4.10 End of programme
"End/Cancel" light on the programme follow-up indicator will
light up once the programme comes to an end; and "Door
Open" symbol flashes for 1-2 minutes until the door is ready
to open. When "Door Open" symbol is steadily illuminated, the
door can be opened.
If you want to open loading door when the machine is in use,
press "Start / Pause" button to pause the machine. "Door
Open" light will start flashing when the machine is switched
to Pause mode. Machine checks the level of the water inside.
If the level is suitable, "Door Open" light illuminates steadily
within 1-2 minutes and the loading door can be opened.
If the level is unsuitable, "Door Open" light turns off and the
loading door cannot be opened. If you are obliged to open
the loading door when the "Door Open" light is off, you
have to cancel the current programme; see "Cancelling the
programme".
To turn off the machine, turn program selection knob to "On
/ Off" position. Take out your laundry and close the loading
door. The machine will be ready for the next run.
4.11 Door Open
"Door Open" symbol is illuminated when the door is ready
to open. It flashes until the door gets ready to open. If the
"Door Open" symbol is not illuminated, do not force the door
to open. The symbol's light is steady when the door is ready
to open.
Switching the machine to pause mode
Press the "Start / Pause" button to switch the machine to
pause mode while a programme is running. "Running" light
starts flashing on the Programme Follow-up indicator to show
that the machine has been switched to the pause mode.
When the loading door is ready to be opened, "Door Open"
light will illuminate continuously.
4.12 Your machine is equipped
with a “Standby Mode”
In case of not starting any programme or waiting without
making any other operation when the machine is turned on
by On/Off button and while it is in selection step or if no other
operation is performed approximately 2 minutes after the
programme you selected has come to an end, your machine
will automatically switch to energy saving mode. Brightness of
indicator lights will decrease. Also, if your product is equipped
with a display showing the programme duration, this display
will completely turn off. In case of rotating the Programme
Selection knob or pressing any button, lights and display
will restore to their previous condition. Your selections made
while exiting the energy saving mode may change. Check
the appropriateness of your selections before starting the
programme. Readjust if necessary. This is not a fault.
Adding or taking out laundry
Press "Start / Pause" button to switch the machine to pause
mode. When the machine is switched to pause mode,
"Running" light flashes. Wait until the Loading Door can be
opened. Open the Loading Door and add or take out the
laundry.
Close the Loading Door. Press "Start / Pause" button to start
the machine.
INFORMATIONS
C
The door can be opened if the water level is suitable. Door open
symbol flashes until the loading door gets ready to be opened. The
symbol’s light is steady when the door is ready to open. You can
open the door to add/take out laundry.
4.9 Cancelling the programme
To cancel the programme, turn the Programme Selection knob
to select another programme. Previous programme will be
cancelled. "End/Cancel" light will flash continuously to notify
that the programme has been cancelled.
Download from Www.Somanuals.com. All Manuals Search And Download.
Washing Machine / User’s Manual
11 / EN
5.3 Cleaning the body and control panel
5 Maintenance and cleaning
Wipe the body of the machine with soapy water or non-
corrosive mild gel detergents as necessary, and dry with a
soft cloth.
Service life of the product extends and frequently faced
problems decrease if cleaned at regular intervals.
Use only a soft and damp cloth to clean the control panel.
5.1 Cleaning the detergent drawer
Clean the detergent drawer at regular intervals (every
4-5 washing cycles) as shown below in order to prevent
accumulation of powder detergent in time.
A WARNING
Never use sponge or scrub materials. These will damage the
painted and plastic surfaces.
5.4 Cleaning the water intake filters
There is a filter at the end of each water intake valve at the
rear of the machine and also at the end of each water intake
hose where they are connected to the tap. These filters
prevent foreign substances and dirt in the water to enter the
washing machine. Filters should be cleaned as they do get
dirty.
Press the dotted point on the siphon in the softener
compartment and pull towards you until the compartment is
removed from the machine.
INFORMATIONS
C
If more than normal amount of water and softener mixture starts to
gather in the softener compartment, the siphon must be cleaned.
Wash the detergent drawer and the siphon with plenty of
lukewarm water in a washbasin. Wear protective gloves or use
an appropriate brush to avoid touching of the residues in the
drawer with your skin when cleaning. Insert the drawer back
into its place after cleaning and make sure that it is seated
well.
Close the taps. Remove the nuts of the water intake hoses
to access the filters on the water intake valves. Clean them
with an appropriate brush. If the filters are too dirty, take them
out by means of pliers and clean them. Take out the filters
on the flat ends of the water intake hoses together with the
gaskets and clean thoroughly under running water. Replace
the gaskets and filters carefully in their places and tighten the
hose nuts by hand.
5.2 Cleaning the loading door and the drum
Residues of softener, detergent and dirt may accumulate in
your machine in time and may cause unpleasant odours and
washing complaints. To avoid this, use the Drum Cleaning
programme. If your machine does not have a Drum Cleaning
programme, use Cotton-90 programme. Before starting the
programme, put max. 100 g of powder anti-limescale into
the main wash detergent compartment (compartment nr. II).
If the anti-limescale is in tablet form, put only one tablet into
compartment nr. II. Dry the inside of the bellow with a clean
piece of cloth after the programme has come to an end.
5.5 Draining remaining water and
cleaning the pump filter
The filter system in your machine prevents solid items such
as buttons, coins and fabric fibers clogging the pump impeller
during discharge of washing water. Thus, the water will be
discharged without any problem and the service life of the
pump will extend.
If the machine fails to drain water, the pump filter is clogged.
Filter must be cleaned whenever it is clogged or in every 3
months. Water must be drained off first to clean the pump
filter.
In addition, prior to transporting the machine (e.g., when
moving to another house) and in case of freezing of the water,
water may have to be drained completely.
INFORMATIONS
Repeat Drum Cleaning process in every 2 months.
C
Use an anti-limescale suitable for the washing machines.
After every washing make sure that no foreign substance is
left in the drum.
A WARNING
Foreign substances left in the pump filter may damage your
machine or may cause noise problem.
In order to clean the dirty filter and discharge the water:
Unplug the machine to cut off the supply power.
A WARNING
Temperature of the water inside the machine may rise up to 90 ºC.
To avoid burning risk, filter must be cleaned after the water in the
machine cools down.
If the holes on the bellow shown in the figure is blocked, open
the holes using a toothpick.
INFORMATIONS
C
Foreign metal substances will cause rust stains in the drum.
Clean the stains on the drum surface by using cleaning agents for
stainless steel. Never use steel wool or wire wool.
Open the filter cover by pulling it from both sides at the top.
Download from Www.Somanuals.com. All Manuals Search And Download.
Washing Machine / User’s Manual
12 / EN
INFORMATIONS
C
You can remove the filter cover by slightly pushing downwards with
a thin plastic tipped tool, through the gap above the filter cover. Do
not use metal tipped tools to remove the cover.
Follow the steps below to discharge the water.
Place a large container in front of the filter to catch water
from the filter. Loosen pump filter (anticlockwise) until water
starts to flow. Fill the flowing water into the container you
have placed in front of the filter. Always keep a piece of cloth
handy to absorb any spilled water. When the water inside the
machine is finished, take out the filter completely by turning it.
Clean any residues inside the filter as well as fibers, if any,
around the pump impeller region. Install the filter.
Seat the tabs in the lower part into their places first, and then
press the upper part to close.
Download from Www.Somanuals.com. All Manuals Search And Download.
Washing Machine / User’s Manual
13 / EN
6 Technical specifications
Models (EN)
WMP511W
5
WMP511S
5
Maximum dry laundry capacity (kg)
Height (cm)
84
84
Width (cm)
60
60
41.5
57
41.5
57
Depth (cm)
Net weight (±4 kg.)
Electrical input (V/Hz)
Total current (A)
230 V / 50Hz
10
230 V / 50Hz
10
1550
1100
1.00
0.20
9413
• / -
1550
1100
1.00
0.20
9413
• / -
Total power (W)
Spin speed (rpm/ min., max.)
Stand-by mode power (W)
Off-mode power (W)
Main model code
Single Water inlet / Double Water inlet
• Available
INFORMATIONS
C
Technical specifications may be changed without prior notice to improve the quality of the product.
Figures in this manual are schematic and may not match the product exactly.
Values stated on the product labels or in the documentation accompanying it are obtained in laboratory conditions in accordance with the
relevant standards. Depending on operational and environmental conditions of the product, these values may vary.
Download from Www.Somanuals.com. All Manuals Search And Download.
Washing Machine / User’s Manual
14 / EN
7 Troubleshooting
Programme cannot be started or selected.
• Washing machine has switched to self protection mode due to a supply problem (line voltage, water pressure, etc.). >>>
To cancel the programme, turn the Programme Selection knob to select another programme. Previous programme will be
cancelled. (See "Cancelling the programme")
Water in the machine.
• Some water might have remained in the product due to the quality control processes in the production. >>> This is not a
failure; water is not harmful to the machine.
Machine vibrates or makes noise.
• Machine might be standing unbalanced. >>> Adjust the feet to level the machine.
• A hard substance might have entered into the pump filter. >>> Clean the pump filter.
• Transportation safety bolts are not removed. >>> Remove the transportation safety bolts.
• Laundry quantity in the machine might be too little. >>> Add more laundry to the machine.
• Machine might be overloaded with laundry. >>> Take out some of the laundry from the machine or distribute the load by hand
to balance it homogenously in the machine.
• Machine might be leaning on a rigid item. >>> Make sure that the machine is not leaning on anything.
Machine stopped shortly after the programme started.
• Machine might have stopped temporarily due to low voltage. >>> It will resume running when the voltage restores to the
normal level.
Programme time does not countdown. (On models with display)
• Timer may stop during water intake. >>> Timer indicator will not countdown until the machine takes in adequate amount of
water. The machine will wait until there is sufficient amount of water to avoid poor washing results due to lack of water. Timer
indicator will resume countdown after this.
• Timer may stop during heating step. >>> Timer indicator will not countdown until the machine reaches the selected
temperature.
• Timer may stop during spinning step. >>> Automatic unbalanced load detection system might be activated due to the
unbalanced distribution of the laundry in the drum.
INFORMATIONS
C
Machine does not switch to spinning step when the laundry is not evenly distributed in the drum to prevent any damage to the machine and to
its surrounding environment. Laundry should be rearranged and re-spun.
Foam is overflowing from the detergent drawer.
• Too much detergent is used. >>> Mix 1 tablespoonful softener and ½ l water and pour into the main wash compartment of the
detergent drawer.
INFORMATIONS
C
Put detergent into the machine suitable for the programmes and maximum loads indicated in the “Programme and consumption table”. When
you use additional chemicals (stain removers, bleachs and etc), reduce the amount of detergent.
Laundry remains wet at the end of the programme
• Excessive foam might have occurred and automatic foam absorption system might have been activated due to too much
detergent usage. >>> Use recommended amount of detergent.
INFORMATIONS
C
Machine does not switch to spinning step when the laundry is not evenly distributed in the drum to prevent any damage to the machine and to
its surrounding environment. Laundry should be rearranged and re-spun.
A WARNING
If you cannot eliminate the problem although you follow the instructions in this section, consult your dealer or the Authorized Service Agent.
Never try to repair a nonfunctional product yourself.
Download from Www.Somanuals.com. All Manuals Search And Download.
Washing Machine / User’s Manual
15 / EN
PRODUCT FICHE
Complying Commission Delegated Regulation (EU) No 1061/201
Supplier name or trademark
Beko
WMP511W
5
Beko
WMP511S
5
Model name
Rated capacity (kg)
Energy efficiency class (1)
A+
A+
Annual Energy Consumption (kWh) (2)
168
168
Energy consumption of the standard 60°C cotton programme at full load (kWh)
Energy consumption of the standard 60°C cotton programme at partial load (kWh)
Energy consumption of the standard 40°C cotton programme at partial load (kWh)
Power consumption in ‘off-mode’ (W)
0.800
0.745
0.650
0.200
1.00
9900
B
0.800
0.745
0.650
0.200
1.00
9900
B
Power consumption in ‘left-on mode’ (W)
Annual Water Consumption (l) (3)
Spin-drying efficiency class (4)
Maximum spin speed (rpm)
1100
53
1100
53
Remaining moisture Content (%)
Standard cotton programme(5)
Cotton Eco 60°C and 40°C
Programme time of the standard 60°C cotton programme at full load (min)
Programme time of the standard 60°C cotton programme at partial load (min)
Programme time of the standard 40°C cotton programme at partial load (min)
Duration of the left-on mode (min)
145
145
116
N/A
No
145
145
116
N/A
No
Built-in
(1) Scale from A+++ (Highest Efficiency) to D (Lowest Efficiency)
(2) Energy Consumption based on 220 standard washing cycles for cotton programmes at 60°C and 40°C at full and partial load,
and the consumption of the low-power modes. Actual energy consumption will depend on how the appliance is used.
(3) Water consumption based on 220 standard washing cycles for cotton programmes at 60°C and 40°C at full and partial load.
Actual water consumption will depend on how the appliance is used.
(4) Scale from A (Highest Efficiency) to G (Lowest Efficiency)
(5) “Standard 60°C cotton programme” and the “standard 40°C cotton programme” are the standard washing programmes to which
the information in the label and the fiche relates and these programmes are suitable to clean normally soiled cotton laundry and
that they are the most efficient programmes in terms of combined energy and water consumption.
Download from Www.Somanuals.com. All Manuals Search And Download.
Washing Machine / User’s Manual
16 / EN
Download from Www.Somanuals.com. All Manuals Search And Download.
Washing Machine / User’s Manual
17 / EN
Download from Www.Somanuals.com. All Manuals Search And Download.
Washing Machine / User’s Manual
18 / EN
Service
Download from Www.Somanuals.com. All Manuals Search And Download.
Guarantee
Download from Www.Somanuals.com. All Manuals Search And Download.
www.beko.com
|