D1 7081 E
D1 7082 E
D1 7101 E
D1 7102 E
D1 7102 ES
D1 7101 EM
Washing Machine
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
Download from Www.Somanuals.com. All Manuals Search And Download.
1 Your Washing Machine
Overview
Figure 1
1
2
3
Top Lid
4 Height-adjustable Feet
5
6
Detergent Drawer
Control Panel
Loading Door
Filter Cap
TR
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
Models
Maximum dry laundry capacity (kg)
Height (cm)
7
7
7
7
7
7
84
60
61
75
84
60
61
75
84
60
61
75
84
60
61
75
84
60
61
75
84
60
61
75
Width (cm)
Depth (cm)
Net Weight (kg)
Electricity (V/Hz.)
Total Current (A)
Total Power (W)
Spinning cycle (rpm max.)
220-240 V / 50hz
10 10
2000-2350
800 1000 1000 1000 1000
10
10
10
10
800
Specifications of this appliance may change without notice to improve the quality of
the product. Figures in this manual are schematic and may not match your product
exactly.
Values stated on the machine labels or in the documentation accompanying it are
obtained in laboratory in accordance with the relevant standards. Depending on
operational and environmental conditions of the appliance, values may vary.
TR
Download from Www.Somanuals.com. All Manuals Search And Download.
5
2 Warnings
Please read the following information.
Otherwise, there may be the risk of
personal injury or material damage.
Moreover, any warranty and reliability
commitment will become void.
for 3 seconds to cancel the program
set in your machine before calling
the authorized service.
First Use
•
To prepare your machine for
General Safety
washing, carry out your first washing
process without loading your
•
Never place your machine on a
carpet covered floor. Otherwise,
lack of airflow from below of your
machine may cause electrical
parts to overheat. This may cause
problems with your washing
machine and with detergent under
“Cottons 90°C” program.
•
Ensure that the cold and hot water
connections are made correctly
when installing your machine.
Otherwise, your laundry may come
out hot at the end of the washing
process and may wear out.
machine.
•
•
If the power cable or mains plug is
damaged you must call Authorized
Service for repair.
Check water hoses for wear. Do
not use old/used water inlet hoses.
These may cause stains on your
laundry.
•
•
If the current fuse or circuit breaker
is less than 16 Amperes, please
have a qualified electrician install a
16 Ampere fuse or circuit breaker.
While using with or without a
•
Fit the drain hose into the discharge
housing securely to prevent any
water leakage and to allow machine
to take in and discharge water as
required. It is very important that the
water intake and drain hoses are not
folded, squeezed, or broken when
the appliance is pushed into place
after it is installed or cleaned.
Your washing machine is designed
to continue operating in the event
of a power interruption. You cannot
cancel any program by pressing
the “On/Off button.” Your machine
will not resume its program when
the power restores. Press the
“Start/Pause/Cancel” button for
3 seconds to cancel the program
(See, Canceling a Program)
transformer, do not neglect to have
the grounding installation laid by a
qualified electrician. Our company
shall not be liable for any damages
that may arise when the machine is
used on a line without grounding.
To make your machine ready for
use, please be sure that the tap
water supply and water drainage
systems are appropriate before
calling the authorized service. If they
are not, call a qualified plumber to
have any necessary arrangements
carried out.
•
•
Intended use
•
This product has been designed for
home use.
•
The appliance may only be used for
washing and rinsing of textiles that
are marked accordingly.
•
•
There may be some water in your
machine when you receive it. This is
from the quality control process and
is normal. It is not harmful to your
machine.
Some problems you may encounter
may be caused by the infrastructure.
Press “Start/Pause/Cancel” button
•
•
Only detergents, softeners and
supplements suitable for washing
machines may be used.
Observe the care instructions
labeled on textile products and
any other instructions given by
TR
6
Download from Www.Somanuals.com. All Manuals Search And Download.
companies that produce detergents
for your machine.
If there are children in your
house...
•
Electrical appliances may be
dangerous for the children. Keep
children away from the machine
when it is operating. Do not let them
tamper with the machine.
Safety instructions
•
•
•
This appliance must be connected
to an earthed outlet protected by a
fuse of suitable capacity.
The supply and draining hoses must
always be securely fastened and
remain in an undamaged state.
Fit the draining hose to a washbasin
or bathtub securely before starting
up your machine. There may be a
risk of being scalded due to high
washing temperatures!
•
•
Close the loading door when you
leave the area where the machine is
located.
Store all detergents in a safe place
out of reach of the children.
•
•
Never open the loading door or
remove the filter while there is still
water in the drum. Otherwise, there
may be the risk of flooding and
possible injury due to the hot water.
Never force to open the locked
loading door! The loading door will
be ready to open just a few minutes
after the washing cycle comes to an
end.
•
•
Unplug the machine when it is not in
use.
Never wash down the appliance
with a water hose! There is the risk
of electric shock! Always disconnect
from the mains by unplugging before
cleaning.
Never touch the plug with wet
hands. Never unplug by pulling
on the cable, always pull out from
the plug only. Do not operate the
machine if the power cord or plug is
damaged.
•
•
•
Never attempt to repair the machine
yourself. Otherwise, you may be
putting yours and other’s lives in
danger.
For malfunctions that cannot
be solved by information in the
operating manual:
Turn off the machine, unplug it, turn
off the water tap and contact an
authorized service agent.
TR
Download from Www.Somanuals.com. All Manuals Search And Download.
7
3 Installation
3. Fit the covers (supplied in the bag
with the Operation Manual) into the
holes on the rear panel. (“P”)
Removing packaging
reinforcement
Tilt the machine to remove the
packaging reinforcement. Remove the
packaging reinforcement by pulling the
ribbon.
C Keep the transportation safety
bolts in a safe place to reuse when
the washing machine needs to be
moved again in the future.
C Never move the appliance without
the transportation safety bolts
properly fixed in place!
Opening the transportation
Appropriate installation
locks
location
C Transportation safety bolts must
be removed before operating the
washing machine! Otherwise, the
machine will be damaged!
Install the appliance in environments
which have no risk of freezing, in a
stable and level position.
C The floor must be capable of
carrying the load on it!
1. Loosen all the bolts with a spanner
until they rotate freely (“C”)
C If the washing machine and a drier
are placed on top of each other,
their approximate weight together
may reach 180 kg when they are
full.
Important:
•
•
•
Do not place the appliance on top of
the power cable.
Keep at least 1cm distance from the
edges of other furniture.
Place the machine on a firm surface;
do not position it on a long pile rug
or suchlike surfaces.
2. Remove transportation safety bolts
by turning them gently.
Adjusting the feet
C Do not use any tools to loosen the
lock nuts. Otherwise, they can be
damaged.
1. Manually (by hand) loosen the lock
nuts on the feet.
2. Adjust them until the machine
stands level and firmly.
TR
8
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Important: Tighten all lock nuts up
again.
to the tap and the elbowed end
must be attached to the machine.
Tighten the nuts of the hose well by
hand; never use wrenches to tighten
the nuts.
Connecting to the water
supply.
Important:
•
The water supply pressure required
to run the machine must be 1-10
bar (0,1 – 10 MPa). (Practically, it
is necessary to have 10 – 80 liters
of water flowing from the tap in
one minute to have your machine
run smoothly.) Attach a pressure-
reducing valve if the water pressure
is higher.
Connect the special hoses supplied
with the machine to the water intake
valves on the machine. The hose
bearing the “red” sign (90°C max)
is the hot water inlet and the hose
bearing the “blue” sign (25°C max) is
for the cold water inlet.
•
Open the taps completely after
making the hose connection to
check if there is any water leakage
at the connection points. Turn off
the tap and remove the nut in case
of any leakage. Retighten the nut
carefully after checking the seal.
To prevent any water leakage and
any other damage to be caused by
it, keep the taps closed when the
machine is not in use.
Models with a single water inlet
should not be connected to the
hot water tap. Laundry may be
damaged or the appliance may
switch to protection mode and not
work.
•
•
When returning the appliance to its
place after maintenance or cleaning,
care should be taken not to fold,
squeeze or block the hoses.
Connecting to the drain
The water discharge hose can be
attached to the edge of a washbasin or
bathtub. The drain hose should be firmly
fitted into the drain as to not get out of
its housing.
•
In order to prevent water leakage
that may occur at the connection
points, there are rubber seals (4
seals for the models with double
water inlet and 2 seals for other
models) attached to the hoses.
These seals should be used at the
tap and machine connection ends of
the hoses. The plain end of the hose
fitted with a filter must be attached
Important:
•
The end of the drain hose can
be directly connected to the
wastewater drain or to the
washbasin. The fitting must
alwasy be secured in all types of
TR
Download from Www.Somanuals.com. All Manuals Search And Download.
9
connections. Your house may be
flooded if the hose gets out of its
housing during water discharging.
The hose should be attached to a
height of at least 40 cm, and 100
cm at most.
Electrical connection
Connect the machine to an earthed
outlet protected by a fuse of suitable
capacity.
•
•
Important:
•
•
•
Connection should comply with
national regulations.
In case the hose is elevated
after laying it on the floor level or
close to the ground (less than
40 cm above the ground), water
discharge becomes more difficult
and the laundry may come out wet.
Therefore, the heights described in
the figure should be followed.
Power cord plug must be within
easy reach after installation.
The voltage and the allowed fuse
protection are specified in the
section “Technical Specifications”.
The specified voltage must be equal
to your mains voltage.
•
•
Connection via extension cords or
multi-plugs should not be made.
B A damaged power cable must be
replaced by a qualified electrician.
B The appliance must not be operated
unless it is repaired! There is the risk
of electric shock!
Destroying the packaging
material
Packaging material can be dangerous to
children. Keep the packaging materials
out of reach of children or dispose
them by classifying according to
waste directives. Do not dispose them
together with normal domestic wastes.
Packaging materials of your machine are
manufactured from recyclable materials.
•
To prevent dirty water refilling the
machine, and to allow for easy
discharge, the end of the hose
must not be submerged in the drain
water. The end of the hose must be
able to take in air. The hose should
be pushed into the drainage for
more than 15 cm. If it is too long
you may have it shortened.
The end of the hose should not be
bent, it should not be stepped on
and it must not be folded between
the drain and the machine.
the length of the hose is too short,
you may add an extension hose
to the original section. The length
of the hose must not be longer
than 3.2 m after coming out of the
machine. To avoid water leakage
failures, the connection between the
extension hose and the drain hose
of the product must be fitted well
with an appropriate clamp as not to
come off and leak.
Disposing of the old machine
Dispose of your old appliance in an
environmental friendly manner.
•
•
•
You may refer to your local agent or
solid waste collection center in your
municipality to learn how to dispose
of your machine.
Before disposing of your old washing
machine, cut off the mains plug and
make the door lock unusable.
TR
10
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Initial preparations for washing
Sorting the laundry
•
Empty pockets and remove all
foreign objects such as coins, pens
and paper clips. If possible, turn
pockets out and brush.
•
Sort the laundry according to type
of fabric, color, and degree of soiling
and permissible water temperature.
Always follow the advice on the
garment labels.
•
Place small items like infants’
socks and nylon stockings, etc.
in a laundry bag, pillow case or
something similar. This will also save
your laundry from getting lost.
Place curtains in the machine with
care. Remove curtain rails and
pullers.
•
•
•
Fasten zippers, sew loose buttons
and mend rips and tears.
Wash “machine washable” or “hand
washable” labeled products only
with an appropriate program.
Do not wash colors and whites
together. New, dark colored cottons
may release a lot of dye. Wash them
separately.
•
•
•
Tough stains must be treated
properly before washing. If you are
not sure, check with a dry cleaner.
Use only dyes/color changers and
lime removers suitable for machine
wash. Always follow the instructions
on the packaging.
•
•
Wash trousers and delicate clothes
turned inside out.
Preparing clothes for washing
Laundry items with metal attachments
such as, bras, belt buckles and metal
buttons will damage the machine.
Remove metal attachments or place the
items in a clothing bag, pillow case, or
something similar.
Keep laundry items made of Angora
wool in the freezer for a few hours
before washing. This will reduce
pilling.
Correct load capacity
•
The maximum load capacity
depends on the type of laundry, the
degree of soiling and the washing
program you wish to use.
C The machine adjusts the amount of
water according to the amount of
laundry placed inside.
C Please follow the information in the
“Program Selection Table”. Washing
results will degrade when the
machine is overloaded.
TR
Download from Www.Somanuals.com. All Manuals Search And Download.
11
Following weights are given as
examples.
Detergent, softener and other
cleaning agents
Add detergent and softener before
starting the washing program.
Never open the detergent dispenser
drawer while the washing program is
running!
When using a program without pre-
wash, no detergent should be put
into the pre-wash compartment
(Compartment no. I).
A program without pre-wash should
not be selected if a detergent bag or
a dispensing ball is going to be used.
You can place the detergent bag or
the dispensing ball directly among the
laundry in your machine.
Laundry type
Bathrobe
Napkin
Weight (gr)
1200
100
700
500
200
250
200
200
100
600
200
500
100
Duvet cover
Bed Sheet
Pillowcase
Tablecloth
Towel
Evening gown
Underclothing
Men’s coveralls
Men’s shirt
Men’s pajamas
Blouse
Choosing the detergent type
The type of detergent to be used
depends on the type and color of fabric.
Loading door
The door locks during program
•
•
•
Use different detergents for colored
and white clothes.
Wash woolens with a special
detergent specifically for woolens.
Use only detergents manufactured
specifically for washing machines.
operation and the Door Locked Symbol
(Figure 3-13i) lights up. The door can be
opened when the symbol fades out.
•
•
Open the loading door.
Place laundry items loosely in the
machine.
•
Push the loading door until it clicks
into place tightly. Ensure that no
items are caught in the door.
Detergent quantity
The amount of washing detergent to
be used depends on the amount of
laundry, the degree of soiling and water
hardness.
Detergents and softeners
Detergent Drawer
The detergent drawer is composed of
three compartments:
•
Do not use amounts exceeding
the quantities recommended on
the package to avoid problems
of excessive foam, poor rinsing,
financial savings and finally,
environmental protection.
The detergent dispenser may be in two
different types according to the model of
your machine.
- (I) for prewash
- (II) for main wash
•
•
Use small amounts of detergent at a
suitable measure for small amounts
of laundry or for only slightly soiled
laundry.
Use exact measures for highly
concentrated detergents.
- (III) siphon
– ( ) for softener
TR
Download from Www.Somanuals.com. All Manuals Search And Download.
12
for washing machines and always
follow the instructions on the
package.
Detergent
quantity
1/2 measure
for prewashing
for main
washing
1 measure
an additional
1/2 measure
with hard water
Softener
Put the softener into the softener
compartment of the detergent
dispenser.
•
Use the proportions recommended
on the packet.
•
Never exceed the (> max <) level
marking; otherwise, the softener will
be wasted without being used.
If the softener has lost its fluidity,
dilute dense softener with water
before placing it in the detergent
drawer.
•
Liquid detergent
When using liquid or gel washing
detergents, please note the following:
•
•
The liquid detergent may leave
stains on your laundry if time delay
feature is selected.
Do not use liquid detergent if you
want to wash using the time delay
feature.
•
•
Do not use liquid detergent for the
main wash in a cycle with pre-wash.
Use the detergent manufacturer’s
measuring cup and follow the
instructions on the package.
Starch
•
Add liquid starch, powder starch
or the dyestuff into the softener
compartment as instructed on the
package.
•
•
Never use fabric softener and starch
together in the same washing cycle.
Wipe the inside of the drum after
using starch.
Eliminating lime formation
•
When required, use only appropriate
lime removers developed specifically
TR
Download from Www.Somanuals.com. All Manuals Search And Download.
13
5 Selecting a program and operating your machine
Control panel
Figure 2
14
7
13
9
8
11a 11b 11c 11d 10
12
7 – Spin Speed Adjustment Button
8 - Time Delaying Button (+/-)
9 - Temperature Adjustment Button
10 - Start/Pause/Cancel Button
11 - Auxiliary Function Buttons
a- Prewash
b- Quick Wash
c- Rinse Plus
d- Anti-creasing
12 - Program Selection Knob
13 - Display
14 - On / Off Button
TR
Download from Www.Somanuals.com. All Manuals Search And Download.
14
Display symbols
Figure 3
appear. Press “Start/Pause/Cancel”
button (Figure 2-10) to start the
program.
Main programs
Depending on the type of textile, the
following main programs are available:
•Cottons
You can wash your durable clothes
at this program. Your laundry shall
be washed with intense washing
movements during a longer washing
cycle. It is recommended for your
cotton clothes (such as bed sheets,
duvet and pillowcase sets, bathrobes,
underclothing, etc.).
C“Super 40” programme may be
selected instead of “Cotton 60*”
programme during winter in areas
where the input water temperatures
low and/or in areas with low supply
voltage.
13.a - Spin Speed Indicator
13.b – Temperature Indicator
13.c – Spinning Symbol
13.c – Temperature Symbol
13.e – Remaining Time and Delaying
Time Indicator
13.f – Program Indicator Symbols
(prewashing/main washing/rinsing/
softener/spinning)
13.g – Economy Symbol
13.h – Time Delaying Symbol
13.i – Door Locked Symbol
13.j – Start Symbol
13.k – Standby Symbol
13.l – Auxiliary Function Symbols
The auxiliary functions in the table may
differ according to the model of your
machine.
•Intensive
Turning the machine on
Plug in your machine. Turn the tap on
completely. Check if the hoses are
connected tightly. Place the laundry
in the machine. Put in detergent and
softener. Press the “On/Off” button
(Figure 2-14).
You can wash your durable and heavily
soiled clothes at this program. In this
program, your clothes will be washed
for a longer time and an extra rinsing
will be made compared to “Cottons”
program. You can use it for your heavily
soiled clothes that you wish to be rinsed
sensitively.
Program selection
• Mini
Select the appropriate program from
the program table according to type,
amount and soiling degree of the laundry
and washing temperatures.
This program is used to quickly wash
a small number of lightly soiled cotton
garments.
•Hand Wash
Bring the Programme Selection Knob
(Figure 2-12) to the program mode that
you wish to wash your laundry at.
The recommended temperature and
spin speed for the selected program
You can wash your woolen/delicate
clothes that bear “not machine-
washable” labels for which hand wash
is recommended at this program. It
TR
Download from Www.Somanuals.com. All Manuals Search And Download.
15
washes the laundry with very tender
washing movements without wearing
your clothes out.
program.
Each of these main programs comprise
of a complete washing process,
including washing, rinsing and, if
required, spin cycles.
•Woolens
You can wash your machine-washable
woolen garments at this program. Wash
by selecting the proper temperature
according to the labels of your clothes.
It is recommended to use appropriate
detergents for woolens.
C Sort the laundry according to type
of fabric, color, degree of soiling and
permissible water temperature while
choosing a program.
•Delicates
You can wash your delicate clothes
at this program. It has more sensitive
washing movements and does not
make intermediate spinning compared
to “Synthetic” program. It must be used
for clothes for which sensitive washing is
recommended.
C Always select the lowest required
temperature. Higher temperature
means higher power consumption.
C For further program details, see
“Program Selection Table”
Economy Symbol
Shows energy saving programs and
temperature selections.
As “Intensive” and “Baby” programs are
long programs with higher temperature
selections to ensure hygiene, “Economy”
Symbol (Figure 3-13g) will not light up.
•Synthetics
You can wash your less durable clothes
at this program. Lighter washing
movements and shorter washing
cycle is used compared to “Cottons”
program. It is recommended for your
synthetic clothes (such as shirts,
blouses, synthetic/cotton blended
garments, etc.). For curtains and veils, it
is recommended to use “Synthetic 40˚C”
program with prewash and anti-creasing
functions selected. Detergent should
not be put in the prewash compartment.
Less detergent should be put in the
main wash compartment as the veil
foams too much because of its meshed
structure.
e
Special programs
For specific applications, you can select
any of the following programs:
• Rinse
This program is used when you want to
rinse or starch separately.
• Spin
Additional programs
For special cases, there are also extra
programs available:
This program spins with maximum
possible rpm in the default setting.
AYou should use a lower spin rpm for
delicate laundries.
• Baby
Increased hygiene is provided by a
longer heating period and an additional
rinse cycle. It is recommended for baby
clothes and clothes worn by allergic
people.
• Pump
This program is used to discharge the
water of the clothes soaked into water in
the machine.
• Super 40
This program washes for a longer period
at 40°C and gives the same result as
the “Cottons 60°C” program, thus it
saves energy. It is suitable for clothes for
which you cannot use the “Cotton 60°C”
Temperature selection
Whenever a new program is selected,
the temperature anticipated for that
TR
16
Download from Www.Somanuals.com. All Manuals Search And Download.
program appears on the temperature
indicator (13b).
To change the temperature, press
the temperature button (Figure 2-9).
Temperature falls with 10° decrements.
Cold selection is shown with “-” symbol.
e
spin is shown with “ ” symbols.
If you do not want to unload your
clothes immediately after the cotton,
synthetics, woolen and delicate fabrics
program, you may use the rinse hold
function in order to prevent your clothes
become wrinkled in an anhydrous
condition. With this function, your
laundry is kept in the final rinsing water.
If you want to spin your laundry after the
rinse hold function:
When the “Temperature” button is
pressed after coming to the Cold
selection, the maximum temperature of
the program you have selected will be
displayed.
-
-
Adjust the spin speed.
To decrease the temperature, press the
“Temperature” button again.
Press Start/Pause/Cancel Button.
Program resumes. Your machines
drains the water and spins your
laundry.
Normally soiled, white
cottons and linens. (Ex.:
You can use no spin function in order to
drain the water without spinning at the
end of the program.
90˚C
60˚C
coffee table covers,
tablecloths, towels, bed
sheets)
Normally soiled, fade proof
colored linens, cottons
or synthetic clothes
(Ex.: shirts, nightgowns,
pajamas) and lightly soiled
white linen clothes (Ex.:
underwear)
For delicate clothes (Ex.: veil
curtains), blended clothes
including synthetics and
woolens.
40˚C-
30°C-
Cold
Spin Speed selection
Whenever a new program is selected,
the maximum spin speed of the selected
program is displayed on the spin speed
indicator (Figure 3-13a).
To decrease the spin speed, press
the “Spin” button (Figure 2-7). Spin
speed decreases gradually. Then, rinse
hold and no spin options are shown
respectively.
Rinse hold is shown with “ ” and no
TR
Download from Www.Somanuals.com. All Manuals Search And Download.
17
Program and consumption table
Programme Duration
(~min)
Auxiliary
functions
Temperature
Programme
Cottons
Cottons
90
7
7
162
153
49 2.72 max.
1,19¹
•
•
•
•
•
•
•
•
•
•
•
•
• • • • • • • • •
• • • • • • • • •
• • • • • • • • •
145¹
148²
136¹
139²
**60
49
max.
1,33²
Cottons
40
40
60
90
60
40
40
7
7
7
7
3
3
2
133
168
198
148
128
93
124
159
189
139
128
93
49 0.72 max.
49 0.84 max.
70 1.43 max.
Super
•
•
•
Intensive
Babycare
Synthetics
Synthetics
Delicate
*
*
•
• • •
70
59
2.4 max.
800
• • • • • • •
1
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
• • • • •
59 0.79 800
65 0.3 600
• • • • •
• • •
75
75
Woollens
Hand wash
40 1.5
30
67
67
59 0.44 600
40 0.25 600
• • •
1
49
49
• •
max.
55 0.22
***
Mini
30 2.5
30
30
• •
• : Selectable
* : Automatically selected, not cancellable.
**: Energy Label programme (EN 60456)
Water and power consumption and programme duration may differ from the table
shown, subject to changes in water pressure, water hardness and temperature,
ambient temperature, type and amount of laundry, selection of auxiliary functions,
and fluctuations in the supply voltage.
1) For D1 7101 E, D1 7102 E, D1 7102 ES, D1 7101 EM models
2) For D1 7081 E, D1 7082 E models
TR
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick wash
Auxiliary functions
With this program (11b), the wash time
is shortened. “2” symbol will light up on
the display.
Auxiliary Function Selection Keys
•
Use this function for smaller
amounts or slightly soiled laundries.
Rinse plus
This function (11c) allows your machine
to perform an extra rinsing in addition
to the rinsing cycles performed by your
machine after main washing cycle.
Thus, the risk for sensitive skins (babies,
allergic skins and etc.) to be effected by
the minimal detergent remnants on the
laundry is reduced. “3” symbol will light
up on the display.
11a 11b 11c 11d
•
Depending on the program, you can
select the desired auxiliary function
by pressing the keys 11a, 11b, 11c,
11d.
Select the required auxiliary
functions before starting the
program.
Some combinations cannot be
selected together. (Ex.: Prewash
(Figure 2-11a) and Quick Wash
(Figure 2-11b).
Symbol of the selected auxiliary
function (Figure 3-13l) will light up.
Anti-creasing
With this function (11d), boiler
movement will be lessened to prevent
creasing and spinning speed is limited.
In addition, washing is carried out at a
higher water level. “4” symbol will light
up on the display.
•
•
•
Use this function for delicate
laundries that crease easily.
C Whenever you select this auxiliary
function, load your machine with
half of the maximum laundry amount
specified in the program table.
•
Auxiliary function selection
If an auxiliary function that should not
be selected together with a previously
selected function is chosen, the first
selected function will be cancelled and
the last auxiliary function selection will
remain active.
Time screen
The display shows the time remaining
for the program to complete while a
program is running. Time is displayed in
hours and minutes as “01:30”.
(Ex.: If you want to select prewash first
and then quick wash, prewash will be
cancelled and quick wash will remain
active.
Auxiliary function that is not compatible
with the program cannot be selected.
(see, “Program Selection Table”)
Prewash
When you select this function (11a), the
display will indicate “1” symbol.
•
Program duration may differ from
the values in the consumption table
subject to the changes in the water
pressure, water hardness and
temperature, ambient temperature,
type and amount of laundry, auxiliary
functions selected, and changes in
•
A prewash is only required with
heavily soiled laundry. Without
prewash you save energy, water,
detergent and time.
•
Prewash without detergent is
recommended for veils and curtains.
TR
Download from Www.Somanuals.com. All Manuals Search And Download.
19
the supply voltage.
Time delay
symbol (Figure 3-13j) will light up.
4. The “:” in the middle of the displayed
time delay will start flashing.
With the “Time delay” function you can
delay the program start up to 24 hours.
Setting can be made in intervals of 30
minutes.
1. Open the loading door, place the
laundry inside and fill with detergent.
2. Set the washing program,
temperature, spin speed and,
if required, select the auxiliary
functions.
Canceling the time delay
If you want to cancel the time delay
countdown and start the program
immediately:
1. Press “Start/Pause/Cancel” button
(Figure 2-10). The “:” in the middle
of the displayed time delay will stop
flashing.
2. Start symbol (Figure 3-13j) will fade.
The standby symbol (Figure 3-13k)
and the time delaying symbol (Figure
3-13h) will flash.
3. Press time delaying button “-”
(Figure 2-8) to decrease the desired
time delay. Program duration after
30 minutes shall be displayed.
4. Press “Start/Pause/Cancel Button”
(Figure 2-10) to start the program.
3. Press “Time delaying” buttons “+”
and “-” (Figure 2-8) to set your
desired time delay. Time delaying
symbol (Figure 3-13h) will flash.
4. Press “Start/Pause/Cancel” button
(Figure 2-10). Then the time delay
starts to count down. Time delaying
symbol (Figure 3-13h) will light up.
Start symbol (Figure 3-13j) will light
up.
The “:” in the middle of the displayed
time delay will start flashing.
Starting the Program
1. Press “Start/Pause/Cancel” button
(Figure 2-10) to start the program.
2. The start symbol (Figure 3-13j)
which indicates that the program
has started will light up.
•
More laundry may be loaded or
taken out during the time delay
period. At the end of the time delay
countdown process, time delaying
symbol (Figure 3-13h) fades and
the washing starts as the program
duration is displayed.
3. The door locks and the door locked
symbol (Figure 3-13i) will light up.
4. Symbol of the relevant step
(prewash, main wash, rinse, softener
and spin) that the program has
started from will light up (Figure 3-
13f).
Changing the delay time
If you want to change the time during
the countdown:
1. Press “Start/Pause/Cancel” button
(Figure 2-10). “:” in the middle of the
screen will stop flashing. Standby
symbol (Figure 3-13k) will light up.
Time delaying symbol (Figure 3-13h)
will flash. Start Symbol (Figure 3-13j)
will fade.
2. Press “Time delaying” buttons “+”
and “-” (Figure 2-8) to set your
desired time delay.
3. Press “Start/Pause/Cancel” button
(Figure 2-10). Time delaying symbol
(Figure 3-13h) will light up. Standby
symbol (Figure 3-13k) will fade. Start
Progress of program.
The progress of a running program is
shown through a number of symbols on
the screen.
•
At the beginning of each program
step, the relevant symbol in the
series of symbols will light up and
thus, at the end of the program,
all symbols will remain lit up. The
symbol that is lit up at the far right of
the series of symbols indicates the
step that is being carried out.
TR
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Prewash
that the machine is in standby mode
lights up and the start symbol (Figure 3-
When “Prewash” auxiliary function is
selected, prewash symbol will light up to 13j) that shows the program has started
indicate the beginning of prewash step.
Main wash
and is still continuing fades out.
Main wash symbol will light up to
indicate that the main wash cycle has
started.
Selecting or canceling an auxiliary
function in standby mode
Auxiliary functions can be cancelled or
selected in accordance with the step the
program is at.
Rinse
Rinse symbol lights up at the beginning
of the rinse step.
Softener
Adding/taking out laundry in standby
mode
Softener symbol lights up at the
beginning of softener step.
Spin
The door can be opened if the water
level is suitable. The door locked symbol
Spin symbol will light up at the beginning (Figure 3-13i) will light up until the door
of the final spin, during “Spin” and
“Pump” special programs.
is suitable for opening. This symbol will
fade out as soon as the door is allowed
to open. Laundry may be added / taken
out by opening the door.
•
If the machine is not spinning, the
program may be in rinse hold mode
or the automatic spin correction
system has been activated because
of the excessive unbalanced
distribution of the laundry in the
machine.
Door lock
Door Locked Symbol (Figure 3-13i) lights
up when the loading door is locked. This
symbol will flash until the door is allowed
to open. Do not force the door at this
stage. This symbol will fade out as soon
as the door is allowed to open. You may
open the door after the symbol fades
out.
Changing the selections after
the program has started
The selected spin speed and program
temperature fade out. An empty frame
appears.
Child-proof lock
You can protect the appliance from
being tampered by children by means
of the child-proof lock. In this case, no
change can be made in the running
program.
When the “Program selection” button is
brought to the appropriate position, rpm
and temperature data reappear.
2. The machine is switched to child-lock
by pressing the 2nd and 4th auxiliary
functions for 3 sec. “C:on” (Child lock is
activated) label appears on the screen.
The same symbol will also be displayed
on the screen whenever any button
is pressed while the machine is child-
Switching the machine to standby
mode
Machine is switched to standby mode
by pressing “Start/Pause/Cancel” button
(Figure 2-10) for a short time. Standby
symbol (Figure 3-13k) which indicates
TR
Download from Www.Somanuals.com. All Manuals Search And Download.
21
locked.
Press “Start/Pause/Cancel” button
(Figure 2-10). Standby symbol (Figure 3-
13k) will fade. Start symbol (Figure 3-13j)
will light up. The program continues and
only pumps out the water.
To deactivate the child-proof lock,
press the 2nd and 4th auxiliary function
buttons for 3 sec.
“C:OFF” (Child lock is deactivated) label
appears on the screen.
End of program
When the program is finished, the
symbols of the relevant steps will remain
lit up and the auxiliary function, spin and
temperature data selected at the start-
up of the program will remain selected.
“End” label will appear on the screen.
Ending the program through
canceling
“Start/Pause/Cancel” button (Figure 2-
10) is pressed for 3 seconds to cancel
the program. Start symbol (Figure
3-13j) will flash during cancellation.
After cancellation, the symbol of the
corresponding step at which the
cancellation was made will remain lit and
“End” label will appear on the screen.
Program in rinse hold mode
•
This process is shown with the
flashing Spin Symbol (Figure 3-
13c) and the lit up Standby Symbol
(Figure 3-13k).
If you wish to spin when the machine is
in this mode:
Adjust the spin speed. Press “Start/
Pause/Cancel” button (Figure 2-10).
The program continues, pumps out
the water and spins. Standby Symbol
(Figure 3-13k) fades out and Start
Symbol (Figure 3-13j) lights up.
If you want to discharge the water only
without spinning:
TR
22
Download from Www.Somanuals.com. All Manuals Search And Download.
6 Quick instructions for daily use
Preparation
of a washing cycle (machine allows
1. Turn the tap on completely. Check if
the hoses are connected tightly.
2. Place the laundry in the machine.
3. Add detergent and softener.
Starting
adding more laundry during a future
step only if the water level is low
enough to open the loading door or
if the temperature in the machine is
low).
1. Press the “On/Off” button (Figure 2-
14).
2. Select the program and the
temperature.
3. If desired:
In order to add laundry after the
start-up of the program:
1. Press “Start/Pause/Cancel” button
(Figure 2-10).
2. Open the loading door and put in
more laundry.
–
–
–
select any auxiliary function,
adjust the spin speed,
set the time delay,
3. Close the loading door.
4. Press “Start/Pause/Cancel” button
(Figure 2-10).
4. Close the loading door.
5. Press “Start/Pause/Cancel” button
(Figure 2-10).
Program is in rinse hold mode
C This process is shown with the
flashing spin symbol (Figure 3-13c)
and the standby symbol (Figure 3-
13k) which is lit up.
If you wish to spin when the machine is
in this mode:
1. Adjust the spin speed.
2. Press “Start/Pause/Cancel”
button (Figure 2-10). The program
continues, pumps out the water and
spins.
3. The standby symbol (Figure 3-13k)
fades out and the start symbol
(Figure 3-13j) lights up.
If you want to discharge the water
without spinning:
1. Press “Start/Pause/Cancel” button
(Figure 2-10).
2. The standby symbol (Figure 3-13k)
fades out and the start symbol
(Figure 3-13j) lights up.
3. The program continues and only
pumps out the water.
Re-spinning the laundry
The control system for an unbalanced
load can pause the spinning in cases
when the distribution of the laundry in
the drum is not balanced.
The display shows the time remaining for
the program to complete if time delay is
not set.
The display shows the time remaining
for the program to start if the time delay
is set.
6. Check if the Door Locked Symbol
(Figure 3-13i) lights up on the
screen.
The Door Locked Symbol (Figure 3-13i)
will light up if time delay is not set.
The Door Locked Symbol (Figure 3-13i)
will fade if time delay is set.
Canceling a program
1. Press and hold the “Start/Pause/
Cancel” button (Figure 2-10) for
about 3 seconds; the Start symbol
(Figure 3-13j) will start flashing.
2. The machine can discharge all
the water or can take in water for
3 times at most to cool down the
clothes and complete discharging
process.
Adding more laundry
•
This is only possible under the
following conditions:
during time delay,
–
C You may add or remove laundry
during the time delay (until the
program starts). At the beginning
If you want to re-spin the clothes:
1. Distribute the laundry in your
machine for a balanced load.
TR
Download from Www.Somanuals.com. All Manuals Search And Download.
23
2. Select the spin program.
3. Adjust the spin speed.
After the program is finished
Program indicator symbols (Figure 3-
13f) on the screen will remain lit after the
program is finished. “End” will appear on
the screen.
1. Open the loading door and take out
the laundry when the door locked
symbol on the display (Figure 3-13i)
fades out.
2. Press the “On/Off” button (Figure 2-
14).
3. Turn the water tap off.
4. Remove any folds in the rubber seal
on the loading door and check for
debris.
5. Leave the loading door and
detergent drawer open to dry.
TR
Download from Www.Somanuals.com. All Manuals Search And Download.
24
7 Cleaning and care
Detergent drawer
Remove any powder residue buildup in
the drawer. To do this;
1. Press the dotted point on the
siphon in the softener compartment
and pull towards you until the
compartment is removed from the
machine.
Body and control panel
When necessary:
•
Wipe the exterior panels of your
machine with soapy water or mild
detergent. Dry it with a soft cloth.
Use only a soft and damp cloth to
clean the control panel.
•
C If more than a normal amount of
water and softener mixture starts to
gather in the softener compartment,
the siphon must be cleaned.
2. Wash the dispenser drawer
and the siphon with plenty of
lukewarm water in a washbasin.
Wear protective gloves or use an
appropriate brush to avoid touching
the residues in the drawer when
cleaning.
C Never use a sponge or scrubbing
material. These will damage the
painted and plastic parts.
Inlet water filters
There is a filter at the end of each
water intake valve at the back side of
the machine and also at the end of
each water intake hose where they
are connected to the tap. These filters
prevent the foreign substances and dirt
in the water to enter into the machine.
Filters should be cleaned as they get
dirty.
3. Replace the drawer into its housing
after cleaning. Check if the siphon
is in its original location.
•
•
Close the taps.
The loading door and the
Remove the nuts of the water intake
hoses to clean the surfaces of the
filters on the water intake valves with
an appropriate brush.
drum
After each wash:
•
Check if there are any foreign
substances in the drum.
Open the hole in the bellow with the
aid of a toothpick if it is clogged.
•
•
If the filters are very dirty, you can
pull them out by means of pliers and
clean them.
Take out the filters on the flat
ends of the water intake hoses
together with the gaskets and clean
thoroughly under streaming water.
Replace the gaskets and filters
carefully to their places and tighten
the hose nuts by hand.
•
C Foreign metal substances in your
machine can cause rust stains. In
such cases:
•
Clean the drum with a stainless steel
cleaning agent. Never use steel wool
or wire wool.
TR
Download from Www.Somanuals.com. All Manuals Search And Download.
25
Draining any remaining water
and cleaning the pump filter
Filter system in your machine prevents
solid items such as buttons, coins and
fabric fibers clogging the pump propeller
during discharging of the washing
water. Thus, a good water discharger is
achieved and the pump life is extended.
If it is composed of one piece, hold it
from both sides and open it by pulling
out.
3- An emergency drain hose is supplied
with some of our models. Others are not
supplied with this item.
•
If your machine fails to drain the
water, the pump filter may be
clogged. You may have to clean
it every 2 years or whenever it is
plugged. Water must be drained off
to clean the pump filter.
If your product is supplied with an
emergency drain hose, do the following
as shown in the figure below:
In addition, water may have to be
drained off completely in the following
cases:
•
before transporting the machine
(e.g. when moving house)
•
when there is the danger of frost
In order to clean the dirty filter and
discharge the water;
1- Unplug the machine to cut off the
supply power.
A There may be water at 90°C in the
machine. Therefore, the filter must
be cleaned only after the inside
water is cooled down to avoid
hazard of scalding.
•
•
Pull out the pump outlet hose from
its housing.
Place a large container at the end of
the hose. Drain the water off into the
container by pulling out the plug at
the end of the hose. If the amount
of water to be drained off is greater
than the volume of the container,
replace the plug, pour the water out,
then resume the draining process.
After draining process is completed,
replace the plug into the end of the
2- Open the filter cap. The filter cap
may be composed of one or two pieces
according to the model of your machine.
If it is composed of two pieces, press
the tab on the filter cap downwards and
pull the piece out towards yourself.
•
TR
26
Download from Www.Somanuals.com. All Manuals Search And Download.
hose and fit the hose back into its
place.
If your product is not supplied with an
emergency drain hose, do the following
as shown in the figure below:
•
•
Place a large container in front of the
filter to receive water flowing from
the filter.
Loosen pump filter (anticlockwise)
until water starts to flow out of it.
Direct the flowing water into the
container you have placed in front
of the filter. You can use a piece of
cloth to absorb any spilled water.
When there is no water left, turn the
pump filter until it is completely loose
and remove it.
Clean any residues inside the filter
as well as fibers, if any, around the
propeller region.
If your product has a water jet
feature, be sure to fit the filter into
its housing in the pump. Never force
the filter while replacing it into its
housing. Fit the filter fully into its
housing; otherwise, water may leak
from the filter cap.
•
•
•
4- Close the filter cap.
Close the two-piece filter cap of your
product by pushing the tab on it.
Close the one-piece filter cap of your
product by fitting the tabs on the bottom
into their positions and pushing the
upper part of it.
TR
Download from Www.Somanuals.com. All Manuals Search And Download.
27
8 Troubleshooting
Problem
Cause
Machine may have
switched to self
protection mode due to
an infrastructure problem
(such as line voltage,
water pressure, etc.).
Explanation / Suggestion
Program
cannot be
started or
selected.
Reset your machine by pressing “Start/Pause/
Cancel” button for 3 seconds. (see, Canceling a
Program)
There may be some
water in your machine
Water in the
machine.
when you receive it. This It is not harmful to your machine.
is from the quality control
process and is normal.
Be sure the seals of the water inlet hoses are
There is water
coming from
the bottom of
the machine.
There might be problems securely fitted.
with hoses or the pump
filter.
Tightly attach the drain hose to the tap.
Make sure that the pump filter is completely
closed.
Tap may be turned off.
Open the inlet water taps fully.
Water inlet hose might be
bent.
Flatten the water intake hose.
Machine does
not fill with
water.
Water inlet filter might be
clogged.
Clean the water intake filter.
Close the loading door.
Clean or flatten the hose.
Clean the pump filter.
The loading door may be
ajar.
Water outlet hose might
be clogged or twisted.
Machine does
not discharge
water.
Pump filter may be
clogged.
Machine feet might have
not adjusted.
Adjust the machine feet.
Transportation safety
bolts might have not
been removed.
Remove the transportation safety bolts.
There may be a small
Machine
vibrates or
shakes.
amount of laundry in the Add more laundry to the machine.
machine.
The machine may be
overloaded or the clothes Reduce the amount of laundry in the machine or
may be distributed
unevenly.
balance the load by hand.
There machine might be
touching a solid surface
Ensure that nothing touches the machine.
Machine
stopped
Machine can stop
It will resume operating when the voltage is back
to the normal level.
shortly after
the program voltage.
started.
temporarily due to low
TR
28
Download from Www.Somanuals.com. All Manuals Search And Download.
The water
being taken
in is directly
discharged.
Improper position of the
drain hose.
Connect the water draining hose as described in
the operation manual.
No water can
be seen in
the machine
during
This is not a problem.
The water level is not
visible from the outside of
the machine.
washing.
Water level might be
above the lower level of
the door.
Run either the “Pump” or “Spin” program.
Machine might be heating
up the water or it may be Wait until the process is over.
at the spinning cycle.
The door is
jammed.
Due to an electrical
mechanism, the door can
only be opened a few
minutes after the program
has stopped.
Wait until the process is over.
Machine fills
with water
when a
process is
cancelled.
Inside of machine may
be hot.
For safety reasons, water should be cycled in and
out a couple times.
The machine will wait until there is a sufficient
amount of water, which may lengthen the
washing time to avoid poor washing results due
to insufficient water.
Water pressure may be
low.
Supply voltage may be
low.
Washing time is lengthened to avoid poor
washing results when the supply voltage is low.
Cycle time lengthens to heat up the water when
the input water is cold. Also, washing time can be
lengthened to avoid poor washing results.
Input temperature of
water may be low.
Washing time
takes longer
than the time
specified in
the manual
The automatic spin correction system might have
been activated due to the unbalanced distribution
of the laundry in the drum.
There may be an
imbalance of laundry in
the machine.
The laundry in the drum may be clustered
(bundled laundry in a bag). Laundry should be
rearranged and re-spun.
No spinning is performed when the laundry is
not evenly distributed in the drum to prevent any
damage to the machine and to its environment.
Number of rinses and/or
amount of rinse water
might have increased.
Water amount is increased to obtain a better
rinse and a rinse cycle is added when necessary.
TR
Download from Www.Somanuals.com. All Manuals Search And Download.
29
In the case of a paused
countdown while taking
in water:
Timer will not countdown
until the machine is filled
with the correct amount
of water.
The machine will wait until there is a sufficient
amount of water to avoid poor washing results
due to lack of water. Then the timer will start to
count down.
In the case of a paused
countdown at the heating
step:
Time will not count
down until the selected
temperature for the
program is reached
It
continuously
washes.
Remaining
time does not
count down.
The automatic spin correction system might have
been activated due to the unbalanced distribution
of the laundry in the drum.
In the case of a paused
countdown at the
spinning step:
There may be an
imbalance of laundry in
the machine.
The laundry in the drum may be clustered
(bundled laundry in a bag). Laundry should be
rearranged and re-spun.
No spinning is performed when the laundry is
not evenly distributed in the drum to prevent any
damage to the machine and to its environment.
The automatic spin correction system might have
been activated due to the unbalanced distribution
of the laundry in the drum.
It
continuously
spins.
There may be an
imbalance of laundry in
the machine.
The laundry in the drum may be clustered
(bundled laundry in a bag). Laundry should be
rearranged and re-spun.
Remaining
time does not
count down.
No spinning is performed when the laundry is
not evenly distributed in the drum to prevent any
damage to the machine and to its environment.
The automatic spin correction system might have
been activated due to the unbalanced distribution
of the laundry in the drum.
There may be an
imbalance of laundry in
the machine. Therefore,
the program might have
been completed without
spinning.
The laundry in the drum may be clustered
(bundled laundry in a bag). Laundry should be
rearranged and re-spun.
It did not
spin.
No spinning is performed when the laundry is
not evenly distributed in the drum to prevent any
damage to the machine and to its environment.
The machine will not
spin if the water has not
completely drained.
- Check the filter.
- Check the drain hose.
TR
30
Download from Www.Somanuals.com. All Manuals Search And Download.
- Using insufficient
amount of detergent for a
long time,
- Use the recommended amount of detergent
appropriate for water hardness and the laundry.
- Select the proper temperature for the laundry
to be washed.
- Washing at low
temperatures for a long
time,
Washing
performance
is poor:
Laundry turns
gray
- Using insufficient
amount of detergent for
hard waters (soil can stick
to the laundry),
- Using excessive
amount of detergent
(detergent can stick to
the laundry).
- If the water hardness is high, using an
insufficient amount of detergent can cause
laundry to turn gray over time.
- It is difficult to eliminate such grayness once it
occurs.
Insufficient amount of
detergent used.
Use recommended amount of detergent
appropriate for the laundry.
Washing
performance
is poor:
Excessive laundry loaded
into machine
Do not load the machine in excess.
Stain could
not be
Wrong program and
temperature might have
been selected.
Select the proper program and temperature for
the laundry to be washed.
removed, not
cleaned.
Improper detergent may
have been used.
Laundry
could not be
whitened.
Wrong type of detergent Put the detergent in the correct compartment.
used.
Do not mix detergent with bleaching agents.
Such odors and bacteria layers may be formed
on the drum as a result of continuous washing
at lower temperatures and/or in short programs.
Leave the detergent dispenser drawer as well as
the loading door of the machine ajar after each
washing. Thus, a humid environment favorable
for bacteria cannot be created inside the
machine.
Washing
performance
is poor:
Oily accumulations on the
drum may have stuck to
the laundry.
Oily stains
appear on
laundry.
Machine must be operated empty either at 60°C
or 90°C program with detergent every 6 months.
Washing
Oily accumulations on the
drum may have stuck to
the laundry.
performance
is poor:
Machine must be operated empty either at 60°C
or 90°C program with detergent every 6 months.
Bad odor
Excessive laundry might
have been loaded in.
Do not overload the machine.
Color of
the clothes
faded.
Detergent may have
gotten damp.
Store detergent in a closed and dry place. Do not
keep them under high temperatures.
A higher temperature
might have been
selected.
Select the proper program and temperature
according to the type and soiling degree of the
laundry.
TR
Download from Www.Somanuals.com. All Manuals Search And Download.
31
The amount, brand and
storage conditions of the Store detergent in a closed and dry place. Do not
detergent used might not keep them under high temperatures.
be appropriate.
If detergent is put in the prewash compartment
Detergent might have
although prewash cycle is not selected, the
been put in the wrong
machine can take this detergent during rinsing or
compartment.
softener step.
Machine filter may be
Check the filter.
clogged.
It does not
rinse well.
Drain hose may be
Check the drain hose.
folded.
There may be an imbalance of laundry in the
machine.
The laundry in the drum may be clustered
Intermediate spins may
be skipped.
(bundled laundry in a bag). Laundry should be
rearranged and re-spun.
No spinning is performed when the laundry is
not evenly distributed in the drum to prevent any
damage to the machine and to its environment.
If the water hardness is higher, using insufficient
amount of detergent can cause the laundry to
become stiff in time. Use appropriate amount of
detergent according to the water hardness.
Insufficient amount of
detergent used.
If detergent is put in the prewash compartment
Clothes
stiffened.
The detergent may have although prewash cycle is not selected, the
been placed into the
machine can take this detergent during rinsing or
wrong compartment; the softener step.
detergent may be mixed Softener should not come into contact with
with the softener.
detergent when being added.
Wash and clean the drawer with hot water.
If the water hardness is higher, using insufficient
amount of detergent can cause the laundry to
become stiff in time. Use appropriate amount of
detergent according to the water hardness.
Insufficient amount of
detergent used.
Clothes do
not smell like
the softener.
If detergent is put in the prewash compartment
The detergent may have although prewash cycle is not selected, the
been placed into the
machine can take this detergent during rinsing or
wrong compartment; the softener step.
detergent may be mixed Softener should not come into contact with
with the softener.
detergent when being added.
Wash and clean the drawer with hot water.
TR
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Detergent may have been
put in wet dispenser
drawer.
Dry the detergent drawer before putting in
detergent.
Detergent may have
gotten damp.
Store detergent in a closed and dry place. Do not
keep them under high temperatures.
Water pressure might be
low
Detergent
residue in the
dispensing
drawer.
The detergent in the main
wash compartment might
have gotten wet while
taking in the prewash
water..
The detergent dispenser outlet (holes) may have
a problem.
There might be problems with the detergent
dispenser valves.
Detergent might be
mixed with the bleaching
agent.
Softener should not come into contact with
detergent when being added.
Excessive laundry might
have been loaded in.
Do not load the machine in excess.
There is
Wrong program and
temperature might have
been selected.
detergent
left on the
laundry.
Select the proper program and temperature for
the laundry to be washed.
Wrong detergent may
have been used.
Use wool detergents for woolens.
You may not be using
proper detergent for
automatic washing
machines.
Use only automatic washing machine detergents
in your washing machine.
Excessive amount of
detergent may have been Use only sufficient amount of detergent.
used.
Too much detergent
may have been used for
Use only sufficient amount of detergent.
a small amount of lightly
soiled laundry.
Detergent may have been Store detergent in a closed and dry location. Do
stored improperly.
not store in excessively hot places.
Type of material being
washed (lace items will
cause excessive foam
due to their meshed
structure).
There is too
much foam.
Use smaller amounts of detergent for lace items.
If you put detergent in the prewash compartment
although you have not selected a prewash cycle,
the machine can take this detergent during
rinsing or softener step.
Detergent might have
been put in the wrong
compartment.
You may have added too much softener.
The detergent dispenser might be problematic.
Water may be siphoned (pulling the softener into
the washer early) during the fill or rinse cycles.
There might be problems with the valves.
Softener being released
early.
TR
Download from Www.Somanuals.com. All Manuals Search And Download.
33
The plug might not be
plugged in the mains
outlet.
Check the plug.
Fuse may have blown.
Check the fuse.
Machine does work.
Nothing is displayed on
the screen.
Electricity may be cut
off.
Check the supply power.
The “On/Off” button
might have not been
pressed.
Press this button.
The machine did not
start after the program
was selected and the
“Start/Pause/Cancel”
button was pressed.
The front door may be
ajar.
The Rinse Symbol
amongst the Program
Indicator Symbols is
flashing. (Subject to the
model of your machine,
water cut-off symbol
may light up too)
You can restart your machine by
pressing the “Start/Pause/Cancel”
button for a short time after ensuring
that the water is not cut off.
Water may have been
cut off.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
|
