USER’S GUIDE
BOXLIGHT CP-13t
BOXLIGHT
®
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY INSTRUCTIONS
All the safety and operating instructions should be read before
the product is operated.
d. If the projector does not operate normally by following the
operating instructions. Adjust only those controls that are
covered by the operating instructions as improper
adjustment of other controls may result in damage and will
often require extensive work by a qualified technician to
restore the projector to normal operation.
Read all of the instructions given here and retain them for later
use. Unplug this projector from AC power supply before
cleaning. Do not use liquid or aerosol cleaners. Use a damp
cloth for cleaning.
e. If the projector has been dropped or the cabinet has been
damaged.
Do not use attachments not recommended by the
manufacturer as they may cause hazards.
f. When the projector exhibits a distinct change in
performance-this indicates a need for service.
Do not place this projector on an unstable cart, stand, or table.
The projector may fall, causing serious injury to a child or
adult, and serious damage to the projector. Use only with a
cart or stand recommended by the manufacturer, or sold with
the projector. Wall or shelf mounting should follow the
manufacturer's instructions, and should use a mounting kit
approved by the manufacturer.
When replacement parts are required, be sure the service
technician has used replacement parts specified by the
manufacturer that have the same characteristics as the
original part. Unauthorized substitutions may result in fire,
electric shock, or injury to persons.
Upon completion of any service or repairs to this projector, ask
the service technician to perform routine safety checks to
determine that the projector is in safe operating condition.
Do not expose this unit to rain or use near water... for
example, in a wet basement, near a swimming pool, etc...
This projector is equipped with a
grounding type AC line plug.
Should you be unable to insert the
plug into the outlet, contact your
electrician. Do not defeat the
Slots and openings in the back and bottom of the cabinet are
provided for ventilation, to insure reliable operation of the
equipment and to protect it from overheating.
The openings should never be covered with cloth or other
materials, and the bottom opening should not be blocked by
placing the projector on a bed, sofa, rug, or other similar
surface. This projector should never be placed near or over a
radiator or heat register.
safety purpose of this grounding
type plug.
GROUND
Follow all warnings and instructions marked on the projectors.
For added protection to the projector during a lightning storm,
or when it is left unattended and unused for long periods of
time, unplug it from the wall outlet. This will prevent damage
due to lightning and power line surges.
This projector should not be placed in a built-in installation
such as a book case unless proper ventilation is provided.
This projector should be operated only from the type of power
source indicated on the marking label. If you are not sure of
the type of power supplied, consult your authorized dealer or
local power company.
An appliance and cart combination
should be moved with care. Quick
stops, excessive force, and uneven
surfaces may cause the appliance
and cart combination to overturn.
Do not overload wall outlets and extension cords as this can
result in fire or electric shock. Do not allow anything to rest on
the power cord. Do not locate this projector where the cord
may be damaged by persons walking on it.
Never push objects of any kind into this projector through
cabinet slots as they may touch dangerous voltage points or
short out parts that could result in a fire or electric shock.
Never spill liquid of any kind on the projector.
If the projector is to be built into a compartment or similarly
enclosed, the minimum distances must be maintained.
Do not cover the ventilation slot on the projector.
Heat build-up can reduce the service life of your projector, and
can also be dangerous.
Do not attempt to service this projector yourself as opening or
removing covers may expose you to dangerous voltage or
other hazards. Refer all servicing to qualified service
personnel.
20cm
Unplug this projector from wall outlet and refer servicing to
qualified service personnel under the following conditions:
a. When the power cord or plug is damaged or frayed.
b. If liquid has been spilled into the projector.
WALL
PROJECTOR
(FRONT)
PROJECTOR
(SIDE)
c. If the projector has been exposed to rain or water.
50cm
50cm
50cm
3
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
FEATURES AND DESIGN
5
6
COMPUTER MODE
23
SELECTING COMPUTER MODE
SELECTING COMPUTER SYSTEM
PC ADJUSTMENT
23
23
24
PREPARATION
COMPATIBLE COMPUTER SPECIFICATION 26
NAME OF EACH PART OF THE PROJECTOR
6
PICTURE IMAGE ADJUSTMENT
PICTURE POSITION ADJUSTMENT
PICTURE SCREEN ADJUSTMENT
27
28
29
SETTING-UP THE PROJECTOR
POSITIONING THE PROJECTOR
ADJUSTABLE FEET
7
7
7
8
8
9
CONNECTING THE AC POWER CORD
VENTILATION
MOVING THE PROJECTOR
VIDEO MODE
30
SELECTING VIDEO MODE
30
30
30
31
SELECTING COLOR SYSTEM
PICTURE SCREEN ADJUSTMENT
PICTURE IMAGE ADJUSTMENT
CONNECTING THE PROJECTOR 10
TERMINALS OF THE PROJECTOR
CONNECTING TO THE VIDEO EQUIPMENT
CONNECTING TO THE COMPUTER
10
11
12
MCI MODE
32
OPERATING THE PC CARD SLOT
SELECTING MCI MODE
SHOW THE DATA IN THE MEMORY CARD
WRITE DATA INTO THE MEMORY CARD
PICTURE IMAGE ADJUSTMENT
PICTURE POSITION ADJUSTMENT
PICTURE SCREEN ADJUSTMENT
SMART MEDIA AND PC CARD ADAPTER
32
33
34
35
36
36
37
38
BEFORE OPERATION
14
OPERATION OF THE REMOTE CONTROL
LASER POINTER FUNCTION
14
14
15
REMOTE CONTROL BATTERIES INSTALLATION
TOP CONTROLS AND INDICATORS
16
OPERATING ON-SCREEN MENU
HOW TO OPERATE THE ON-SCREEN MENU
FLOW OF ON-SCREEN MENU
MENU BAR
17
17
17
18
SETTING
40
SETTING MENU
SETTING LANGUAGE
40
40
BASIC OPERATION
20
TURNING ON / OFF THE PROJECTOR
20
ADJUSTING THE IMAGE
ZOOM ADJUSTMENT
21
21
21
21
22
22
APPENDIX
41
FOCUS ADJUSTMENT
KEY STONE ADJUSTMENT
NO SHOW FUNCTION
OPERATING WIRELESS MOUSE
MAINTENANCE
41
42
42
42
42
43
43
PICTURE FREEZE FUNCTION
TEMPERATURE WARNING INDICATOR
AIR FILTER CARE AND CLEANING
CLEANING THE PROJECTION LENS
LAMP REPLACEMENT
SOUND ADJUSTMENT
SOUND VOLUME ADJUSTMENT
SOUND MUTE ADJUSTMENT
22
22
22
LAMP REPLACEMENT MONITOR TIMER
TROUBLESHOOTING
TECHNICAL SPECIFICATIONS
44
46
TRADEMARKS
● Apple, Macintosh, and PowerBook are trademarks or registered trademarks of Apple Computer,Inc.
● IBM and PS/2 are trademarks or registered trademarks of International Business Machines, Inc.
● Windows and PowerPoint are registered trademarks of Microsoft Corporation.
● Each name of corporations or products in the owner's manual is a trademark or a registered trademark of its
respective corporation.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
FEATURES AND DESIGN
This Multimedia Projector is designed with the most advanced technology for portability, durability, and ease of
use. The projector utilizes built-in multimedia features, a palette of 16.77 million colors, and matrix liquid crystal
display (LCD) technology.
◆ Compatibility
◆ PC CARD SLOT
This projector is compatible with many different
types of personal computers and video
devices, including;
This projector has the PC CARD SLOT for
easier presentation. Pictures can be projected
just by inserting a memory card including
image data and the presentation data can be
edited by the software "Media Card Imager"
(supplied) easily. Refer to the pages 32 ~ 39
and the Owner's Manual for Media Card
imager for operations.
● IBM-compatible computers, including
laptops, up to 1024 x 768 resolution.
● Apple Macintosh and PowerBook
computers up to 1024 x 768 resolution.
● Various video equipment using any of the
world wide video standards, including
NTSC, NTSC4.43, SECAM, PAL, PAL-M
and PAL-N.
◆ Laser Pointer Function
The Remote Control Unit of this projector has
the Laser Pointer function providing
convenience and smartness for your
presentations.
◆ Image Resolution
Picture Image of the computer is projected in
the resolution of 800 x 600 and it is provided
just as appearing on your computer's monitor.
Screen resolutions between 800 x 600 and
1024 x 768 are compressed to 800 x 600, and
this projector cannot display screen resolutions
above 1024 x 768. If your computer's screen
resolution is higher than 1024 x 768, reset it to
a lower resolution before you connect the
projector.
◆ Other Features
This projector has Motor Zoom/Focus, No
Show, Picture Freeze, Keystone and Mute
functions. And the Air Pad Remote Control is
equipped.
◆ Accessories
This projector comes with the parts listed
below. Check to make sure all are included. If
any part is missing, contact Boxlight
immediately.
● Owner's Manual.
● AC Power Cord.
● Wireless Remote Control Unit.
● Batteries for Remote Control Unit.
● VGA Cable.
◆ Portability
This projector is quite compact in size and
weight. Having a sophisticated shape like an
attaché case with a retractable carrying handle,
the projector will help you make powerful
presentation wherever you go.
◆ Automatic Multiscanning System
● Control Cable for PS/2 Port.
● Media Card Imager for Windows 95 (CD-ROM)
and Owner’s Manual for this software.
● SmartMedia and PC Card Adapter.
● Lens Cover.
This projector automatically tune to the most
personal computers currently distributed by
simply connecting. It is free from complicated
adjustments to project picture images from PC.
● Dust Cover.
◆ Multilanguage Menu Display
Operation menu is displayed in; English,
Deutsch, Français, Italiano, Español, or
Japanese
5
Download from Www.Somanuals.com. All Manuals Search And Download.
PREPARATION
NAME OF EACH PART OF THE PROJECTOR
FRONT OF THE CABINET
PROJECTION LENS
PC CARD SLOT
LENS COVER
CARRY HANDLE
INFRARED REMOTE RECEIVER
SPEAKER (Monaural)
BACK OF THE CABINET
EXHAUST VENT
HOT AIR EXHAUSTED !
Air blown from the exhaust vent is hot.
When using or installing the projector,
following attention should be taken.
● Do not put a flammable object near this
part.
● Keep heat-sensitive objects away from the
exhaust vent.
● Do not touch this part especially screws
and metallic parts. This part will become
hot while the projector is used.
INFRARED
REMOTE RECEIVER
POWER CORD CONNECTOR
BOTTOM OF THE CABINET
AIR INTAKE VENTS
These Air Intake Vents
should not be blocked.
ADJUSTABLE FEET
AND
FEET LOCK LATCHES
LAMP COVER
6
Download from Www.Somanuals.com. All Manuals Search And Download.
PREPARATION
SETTING-UP THE PROJECTOR
POSITIONING THE PROJECTOR
● This projector is basically designed to project on a flat projection surface.
● The projector can be focused from 4.6’(1.4m) ~ 35.4’(10.8m).
● Refer to the figure below to adjust the screen size.
35.4’ (10.8m)
24.0’ (7.3m)
18.0’ (5.5m)
300”
200”
11.8’ (3.6m)
150”
231”
4.6’ (1.4m)
100”
H1
H2
154”
115”
40”
77”
30”
30”
60”
100”
150”
200”
300”
Screen Size
(W x H) mm
610 x 457
1219 x 914
34.3”(870mm)
1.7”(44mm)
2032 x 1524
3048 x 2286
4064 x 3048
6096 x 4572
17.1”(435mm)
0.9”(22mm)
57.1”(1451mm) 85.7”(2177mm) 114.3”(2903mm) 171.4”(4354mm)
2.9”(73mm) 4.3”(109mm) 5.7”(145mm) 8.6”(218mm)
Height (H1)
Height (H2)
ROOM LIGHT
The brightness in the room has a great influence on the picture quality. It is recommended to limit ambient
lighting in order to provide the best image.
ADJUSTABLE FEET
Picture tilt and projection angle can be adjusted by
rotating the ADJUSTABLE FEET. Projection angle can
be adjusted to 10 degrees.
Lift the front of the projector and pull the FEET LOCK
LATCHES on both sides of the projector.
1
Release the FEET LOCK LATCHES to lock the
ADJUSTABLE FEET and rotate the ADJUSTABLE
FEET for fine tune of the position and the tilt.
2
To shorten the ADJUSTABLE FEET, lift the front of the
projector and pull and undo the FEET LOCK LATCHES.
3
FEET LOCK
LATCHES
The position and the keystone distortion of the image
can be also adjusted with the Menu Operation. (Refer
to pages 21, 29, 30 and 37.)
ADJUSTABLE FEET
7
Download from Www.Somanuals.com. All Manuals Search And Download.
PREPARATION
CONNECTING THE AC POWER CORD
This projector uses nominal input voltages of 100-120 V
AC or 200-240 V AC. The projector automatically
selects the correct input voltage. It is designed to work
with single-phase power systems having a grounded
neutral conductor. To reduce the risk of electrical
shock, do not plug into any other type of power system.
Consult your authorized dealer or service station if your
are not sure of the type of power supply being in use.
Connect the projector with the peripheral equipment
before turning the projector on. (Refer to pages 10 ~ 13
for connection.)
Connect the AC power supply cord (supplied) to the
projector.
The socket-outlet must be near this equipment and
must be easily accessible.
CAUTION
For the safety, unplug the AC Power Cord when the
appliance is not used.
When this projector is connected to the outlet with
the AC Power Cord, the appliance is in Stand-by
Mode and consumes a little electric power.
AC outlet side (Male)
Projector side (Female)
VENTILATION
This projector is equipped cooling fans for protection from overheating. Pay attention to the following to
ensure the ventilation and avoid a possible risk of fire and malfunction.
● Do not cover the vent slot.
● Keep the rear grill at least one meter away from any
object.
● Make sure that there is no object on both sides of the
EXHAUST VENT
(REAR SIDE)
projector. Those obstacles may prevent the projector
from taking the cooling air through the side Air Intake
Vent Slots.
AIR INTAKE VENTS
(BOTH SIDES)
8
Download from Www.Somanuals.com. All Manuals Search And Download.
PREPARATION
MOVING THE PROJECTOR
Use the Carry Handle when moving the Projector.
When moving the projector, replace the lens cover and rotate
the feet fully clockwise (to shorten the feet) to prevent from
damage to the lens and the cabinet.
When this projector is not used for the extended period,
replace the lens cover, tuck the Adjustable Feet and apply the
dust cover supplied to this projector.
CAUTION IN CARRYING OR TRANSPORTING THE PROJECTOR
● Do not drop or give a shock to the projector, otherwise damages or malfunctions may result.
● When carrying the projector, use a carrying case recommended by Boxlight.
● Do not transport the projector by using a courier or transport service in an unsuitable transport case. This may cause
damage to the projector. To transport the projector through a courier or transport service, use a case recommended
by Boxlight.
● For carrying or transportation cases, contact a Boxlight at 1-800-762-5757 or 360-779-7901.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTING THE PROJECTOR
TERMINALS OF THE PROJECTOR
S-VIDEO INPUT JACK
VIDEO INPUT JACK
Connect the S-VIDEO output
from the video equipment to this
terminal.
Connect the video output from
the video equipment to this
terminal.
(Refer to P11.)
S-VIDEO
(Refer to P11.)
AUDIO INPUT JACKS
COMPUTER AUDIO INPUT JACK
AUDIO
IN
Connect the audio outputs from
the video equipment to these
terminals.
R-AUDIO-L(MONO)
VIDEO
Connect the audio output from
the computer to this terminal.
(Refer to P12, 13.)
OUT
(Refer to P11.)
COMPUTER IN
MONITOR OUT
● When the audio output is
monaural, connect it to the Left
jack.
AUDIO OUTPUT JACK (STEREO)
Connect the audio amplifier to
this terminal.
(Refer to P12, 13.)
CONTROL PORT
COMPUTER INPUT TERMINAL
Connect the computer output to
this terminal.
(Refer to P12, 13.)
CONTROL PORT CONNECTOR
When controlling the computer
with the Remote Control of this
projector, connect the mouse
port of your personal computer
to this terminal. It is also used
for write on or read from the
data of the PC CARD SLOT in
MCI mode.
MONITOR OUTPUT TERMINAL
This terminal outputs the signal
from the COMPUTER IN
terminal. Connect to the monitor
to this terminal.
(Refer to P12, 13.)
(Refer to P12, 13, 35.)
COMPUTER INPUT / MONITOR OUTPUT TERMINAL
Terminal : HDB15-PIN
Connect the display output terminal of the computer to COMPUTER INPUT with the VGA Cable (supplied). And connect
the monitor to MONITOR OUTPUT with the monitor cable (not supplied). When connecting the Macintosh computer, the
MAC Adapter (not supplied) is required.
1
2
3
4
5
6
7
8
Red Input
Green Input
Blue Input
Sense 2
9
Non Connect
Pin Configuration
10 Ground (Vert.sync.)
11
12
Sense 0
Sense 1
Horiz. sync.
Vert. sync.
Reserved
2
1
5
4
3
10
9
8
7
6
Ground (Horiz.sync.) 13
Ground (Red)
Ground (Green) 15
Ground (Blue)
15
12
14
13
11
14
CONTROL PORT CONNECTOR
Terminal : Mini DIN 8-PIN
Connect control port (PS/2, Serial or ADB port) on your computer to this terminal with the Control Cable (the Control
Cable for PS/2 port is supplied).
PS/2
-----
CLK
DATA
GND
-----
-----
GND
-----
Serial
R X D
-----
-----
GND
RTS
T X D
GND
GND
ADB
-----
ADB
-----
GND
-----
-----
Pin Configuration
1
2
3
4
5
6
7
8
8
7
6
5
4
3
2
1
-----
GND
10
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTING THE PROJECTOR
CONNECTING TO THE VIDEO EQUIPMENT
Video Source (example)
Video Cassette Recorder
Video Disc Player
Video / Audio Output
S-VIDEO Output
Used cables for connection
• VIDEO CABLE ✽
• S-VIDEO CABLE ✽
• AUDIO CABLE (stereo) ✽
Use the either of VIDEO
jack or S-VIDEO jack.
When the both jacks are
connected, the S-VIDEO
jack has priority over the
VIDEO jack.
✽ These cables are not supplied
with this projector.
Video Audio Cable ✽
S-VIDEO Cable ✽
Terminals
of the Projector
S-VIDEO
AUDIO
IN
R-AUDIO-L(MONO)
VIDEO
OUT
COMPUTER IN
MONITOR OUT
CONTROL PORT
Audio Cable (Stereo) ✽
Audio Input
External Audio Equipment
NOTE :
When connecting the cable, the power cords of
both the projector and the external equipment
should be disconnected from AC outlet. Turn the
projector and peripheral equipment on before the
computer is switched on.
Audio Speaker
(stereo)
Audio Amplifier
11
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTING THE PROJECTOR
CONNECTING TO THE COMPUTER
To connect with the computer, refer to the figure below.
Used cables for connection
• VGA CABLE
• CONTROL CABLE FOR PS/2 PORT
• CONTROL CABLE FOR SERIAL PORT,or ADB PORT ✽
• MAC ADAPTER ✽
• MONITOR CABLE ✽
• PC AUDIO CABLE (stereo) ✽
✽ These cables are not supplied with this projector.
IBM-compatible computers or Macintosh computers (VGA / SVGA / XGA / SXGA)
Desktop type
Laptop type
Monitor
Audio Speaker
(stereo)
Audio Amplifier
Audio Input
To each terminal of your computer
To the Monitor
Monitor Output
Serial port PS/2 port
ADB port Audio Output
MAC Adapter ✽
Set the slide
ON
DIP
switches following
the chart on the
next page.
1
2
3
4
5
6
Terminal
Terminal
Terminal
Audio Cable (stereo) ✽
Control Cable for ADB Port ✽
Control Cable for PS/2 Port
Control Cable for Serial Port ✽
VGA Cable
Monitor Cable ✽
NOTE :
When connecting the cable, the power cords of both the projector and the external equipment should be disconnected
from AC outlet. Turn the projector and peripheral equipment on before the computer is switched on.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTING THE PROJECTOR
S-VIDEO
AUDIO
IN
R-AUDIO-L(MONO)
VIDEO
OUT
COMPUTER IN
MONITOR OUT
CONTROL PORT
COMPUTER
IN
MONITOR
OUT
CONTROL
PORT
AUDIO
IN
AUDIO
OUT
◆ MAC ADAPTER (Not supplied)
Set the switches as shown
in the table below depend-
ing on the RESOLUTION
MODE that you want to
use before your turn on the
projector and computer.
ON
Use one of these Control
ON
DIP
Cables corresponding
with the terminal of your
computer.
1
2
3
4
5
6
OFF
1
2
3
4
5
6
13" MODE (640 x 480)
16" MODE (832 x 624)
19" MODE (1024 x 768)
ON ON OFF OFF OFF OFF
OFF ON OFF ON OFF OFF
OFF ON ON OFF OFF OFF
13
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE OPERATION
OPERATION OF THE REMOTE CONTROL
VIDEO BUTTON
Used to select VIDEO
source. (P30)
POWER ON-OFF BUTTON
Used to turn the projector on
or off. (P20)
Left Side
COMPUTER/
MCI
ON-OFF
VIDEO
ZOOM FOCUS
VOLUME
COMPUTER / MCI BUTTON
Used to select source either
COMPUTER or MCI mode.
(P23, 33)
D.ZOOM
MUTE
PAGE
POINT BUTTON
MENU BUTTON
Used to call MENU
operation. (P17-19)
Used to move the pointer on
the MENU, to adjust the item,
or to pan the image in DIGITAL
ZOOM mode. (P29, 37)
MENU
It is also used as a PC mouse
in Wireless Mouse Operation.
(P41)
SELECT BUTTON
✽ When pressing the center of this
button, it works as the SELECT
button.
Used to execute the item
selected or to expand the
image in DIGITAL ZOOM
mode. (P29, 37)
It is also used as a PC mouse
in Wireless Mouse Operation.
(P41)
LASER
RIGHT CLICK BUTTON
ALL-OFF SWITCH
KEYSTONE
NO SHOW
Used to compress the image
in DIGITAL ZOOM mode.
(P29, 30, 37)
When using the Remote Control
Unit, turn this switch to “ON” and
turn it “ALL OFF” when it is not
used.
FREEZE
It is also used as a PC mouse
in Wireless Mouse Operation.
(P41)
AUTO IMAGE
NORMAL
LASER BUTTON
Used to operate laser pointer
function. The laser beam is
emitted while pressing this
button within 1 minute. When
using the laser pointer for
more than 1 minute, release
the button and press it again.
LASER POINTER FUNCTION
This remote control emits a laser beam as the Laser Pointer from the Laser Light Window. When the LASER button is
pressed, the laser light goes on. And when the button is pressed more than 1 minute or the button is released, light goes off.
Laser light is emitted with the RED light which tells the laser beam being emitted.
The laser emitted is a class II laser; therefore, do not look into the Laser Light Window or shine the laser beam on yourself or
other people. The three marks bellow are the caution labels for the laser beam.
CAUTION : Use of controls or adjustments or performance of procedures other than those specified herein may result in
hazardous radiation exposure.
These caution labels are put on the remote control.
Laser Light Window
14
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE OPERATION
Operating Range
VOLUME BUTTON
Used to adjust volume.
(P22)
COMPUTER/
MCI
ON-OFF
Point the remote control toward the
projector (Receiver Window) when
pressing the buttons. Maximum
operating range for the remote
control is about 16.4’ (5m) and 60°
front and rear of the projector
VIDEO
ZOOM BUTTON
Used to adjust zoom.
(P21)
ZOOM FOCUS
VOLUME
D.ZOOM BUTTON
Used to turn the projector
into DIGITAL ZOOM
mode. (P29, 37)
FOCUS BUTTON
Used to adjust focus.
(P21)
D.ZOOM
MUTE
MENU
PAGE
PAGE BUTTONS
Used to move to next /
previous page of the data
in memory card. This
buttons are activated in
MCI mode only. (P34)
60°
MUTE BUTTON
Used to mute sound.(P22)
16.4’
(5 m)
FREEZE BUTTON
Used to stop the picture.
(P22)
LASER
NO SHOW BUTTON
Used to turn the picture
into black image. (P22)
KEYSTONE
NO SHOW
FREEZE
NORMAL BUTTON
Used to reset to normal
picture adjustment preset
by the factory.
AUTO IMAGE
NORMAL
AUTO IMAGE BUTTON
Use to operate AUTO
IMAGE function. (P28)
16.4’
(5 m)
(P27, 31, 36)
60°
KEY STONE BUTTON
Used to correct the key
stone distortion.
(P22, 29, 30, 37)
REMOTE CONTROL BATTERIES INSTALLATION
Remove the battery
compartment lid.
Slide the batteries into the
compartment.
Replace the compartment
lid.
1
2
3
Press the lid down-
ward and slide it.
Two AA size batteries
For correct polarity (+
and –), be sure the
battery terminals are in
contact with the pins in
the compartment.
To insure safe operation, please observe the following precautions :
● Use (2) AA, UM3 or R06 type alkaline batteries.
● Replace two batteries at the same time.
● Do not use a new battery with a used battery.
● Avoid contact with water or liquid.
● Do not expose the Remote Control Unit to moisture, or heat.
● Do not drop the remote control unit.
● If batteries have leaked on the remote control, carefully wipe the case clean and load new batteries.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE OPERATION
TOP CONTROLS AND INDICATORS
NORMAL BUTTON
Used to reset to normal
picture adjustment preset
by factory. (P27, 31, 36)
AUTO IMAGE BUTTON
PAGE BUTTONS
Used to operate AUTO
IMAGE function. (P28)
Used to move to the next /
previous page of the data in
the memory card plugged
into PC CARD SLOT.
These buttons are used to
stop or resume AUTO-
POWER ON–OFF BUTTON
Used to turn the projector
on or off. (P20)
PLAY function.
Page
buttons are activated in
MCI mode. (P34.)
NORMAL
PAGE
VOLUME
LAMP INDICATOR
This indicator is lit in dim
when the projector is
turned on. And the light is
brightened when the
projector is in stand-by
mode.
VOLUME BUTTONS
Used to adjust volume.
(P22)
LAMP
AUTO IMAGE
MODE BUTTON
READY
Used to select input source
either Computer, Video or
MCI mode. (P23, 30, 33)
ON–OFF
MENU
MODE
READY INDICATOR
This indicator is lit in green
when the projector is ready
to be turned on.
WARNING
TEMP.
SELECT BUTTON
SELECT
Used to execute the item
selected. It is also used to
expand the image in
DIGITAL ZOOM mode.
(P29, 37)
WARNING TEMP. INDICATOR
LAMP
REPLACE
This indicator flashes red
when internal projector
temperature is too high.
(P42)
ZOOM
FOCUS
POINT BUTTONS
Used to select an item and
adjust the value on the
MENU. It is also used to
pan the image in DIGITAL
ZOOM mode. (P29, 37)
LAMP REPLACE INDICATOR
This indicator turns to
yellow when the life of the
projection lamp draws to an
end. (P43)
FOCUS BUTTONS
Used to select focus adjust.
(P21)
MENU BUTTON
Used to open or close the
MENU operation.
(P17, 19)
ZOOM BUTTONS
Used to select zoom adjust.
(P21)
16
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE OPERATION
OPERATING ON-SCREEN MENU
HOW TO OPERATE ON-SCREEN MENU
You can control and adjust this projector through ON-
WIRELESS REMOTE CONTROL
SCREEN MENU. Refer to the following pages to
operate the each adjustment on the ON-SCREEN
MENU.
POINT BUTTON
Used to move the
Pointer to UP/ DOWN/
RIGHT/ LEFT.
1 MOVING THE POINTER
Move the pointer (see the NOTE below) by pressing POINT
button(s) on the TOP CONTROL or the REMOTE CONTROL.
SELECT BUTTON
Used to select the item.
2 SELECT THE ITEM
TOP CONTROL
Select the item by pressing SELECT button.
SELECT BUTTON
Used to select the item.
NOTE : Pointer is the icon on the ON-SCREEN Menu to
select the item. See the figures on the section
"FLOW OF ON-SCREEN MENU" below.
SELECT
POINT BUTTONS
Used to move the
Pointer to UP/ DOWN/
RIGHT/ LEFT.
FLOW OF ON-SCREEN MENU
MENU BAR
Display ON-SCREEN MENU
Press MENU button to display the ON-SCREEN MENU
(MENU BAR). The red frame is the POINTER.
1
POINTER
(red frame)
SELECT
BUTTON
ITEM ICON
Select the Item
Move the POINTER (red frame) to the ITEM ICON that
you want to select by pressing POINT RIGHT/ LEFT
buttons.
2
Select the ITEM by pressing SELECT button. The
dialog box of the ITEM appears.
POINTER
(red frame)
3
Control and adjust through ON-SCREEN MENU
MENU
Move the POINTER downward by pressing POINT
DOWN button. (The shape of POINTER become an
arrow.)
4
POINT
DOWN
Move the POINTER to the ITEM that you want to adjust
and adjust the ITEM by pressing SELECT button.
Refer to the following pages for details of respective
adjustments.
BUTTON
5
POINTER
17
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE OPERATION
MENU BAR
MENU BAR IN COMPUTER MODE
Press MENU BUTTON while being in Computer mode.
PC ADJUST MENU
SETTING MENU
MODE MENU
SYSTEM MENU
POSITION MENU
Used to adjust the
parameters to
match with the input
signal format.
Used to set the Display
Menu and to reset
Lamp Replacement
Monitor Timer.
Used to select
the Computer
input mode.
Used to select a
computer
system.
Used to adjust
the position of
the image.
(Refer to P24, 25)
(Refer to P40)
(Refer to P23)
(Refer to P23)
(Refer to P28)
AUTO IMAGE MENU
IMAGE MENU
SCREEN MENU
LANGUAGE MENU
Used to adjust Fine
sync., Total dots,
and Picture Position
automatically.
Used to adjust the
computer image. [Fine
sync. / Total dots /
White Balance /
Contrast / Brightness]
(Refer to P27)
Used to adjust
the size of the
image.
Used to select
the language
used in the
Menu.
(Refer to P29)
(Refer to P28)
(Refer to P40)
MENU BAR IN VIDEO MODE
MODE MENU
Press MENU BUTTON while being in Video mode.
IMAGE MENU
Used to adjust the
Color /
Tint / White Balance /
Contrast / Brightness/
picture image. [
Used to select
the Video input.
(Refer to P30)
These icons have the
same function as the
Computer Mode.
Sharpness
]
(Refer to P31)
SYSTEM MENU
SCREEN MENU
Used to select a
color system among
Used to set the size
of the image either
Regular or Wide,
or to correct the
PAL, SECAM, NTSC,
[
NTSC 4.43, PAL-M and
PAL-N
].
(Refer to P30)
Keystone distortion.
(Refer to P30)
18
Download from Www.Somanuals.com. All Manuals Search And Download.
MENU BAR IN MCI MODE
Press MENU BUTTON while being in MCI mode.
IMAGE MENU
MODE MENU
Used to adjust the
computer image. [Fine
sync. / Total dots /
White Balance /
Contrast / Brightness]
(Refer to P36)
Used to select
the MCI input
mode.
These icons have the
same function as the
Computer Mode.
(Refer to P33)
VIEW MENU
POSITION MENU
SCREEN MENU
Used to display, read
or write the image data
in a memory card
through the PC CARD
SLOT.
Used to adjust
the position of
the image.
Used to adjust
the size of the
image.
(Refer to P36)
(Refer to P37)
(Refer to P34, 35)
19
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC OPERATIONS
TURNING ON / OFF THE PROJECTOR
TURNING ON THE PROJECTOR
Complete the peripheral connections (with Computer, VCR,
and etc.) before turning on the projector. (Refer to
"CONNECTING TO THE PROJECTOR" on Pages 10~13 for
connecting those equipment.
1
Connect the projector's AC power cord into a wall outlet. The
LAMP indicator lights RED, and the READY indicator lights
GREEN.
2
3
30
Press the power ON-OFF button on the Remote Control Unit or
on the Top Control to ON. The LAMP POWER indicator dims,
and the Cooling Fans start to operate. The Preparation Display
appears on the screen and the count-down starts. The signal
from the source appears after 30 seconds.
The Preparation Display disappears after 30 seconds.
TURNING OFF THE PROJECTOR
Press the power ON-OFF button on the Remote Control Unit or
on the Top Control, and the message "Power off?" appears on
the screen.
1
2
Power off?
Press again the power ON-OFF button to turn off the projector.
The LAMP indicator lights bright and the READY indicator turns
off. The Cooling Fans operate for 90 seconds after the
projector is turned off. (During this "Cooling Down" period, this
appliance cannot be turned on.)
The message disappears after 4 seconds.
When the cooling the projector has finished, the READY
indicator turns to green again and you can turn the projector
on. After cooling down completely, disconnect the AC power
cord.
3
TO MAINTAIN THE LIFE OF THE LAMP, ONCE YOU TURN IT ON, WAIT AT LEAST 5
MINUTES BEFORE TURNING IT OFF.
When the TEMPERATURE WARNING indicator flashes red, the projector is automatically turned off. Wait
at least 5 minutes before turning the projector on again.
If the TEMPERATURE WARNING indicator continues to flash, follow procedures below:
1. Disconnect the AC power cord from the AC outlet.
2. Check the air filters for dust accumulation.
3. Clean the Air Filter. (See "AIR FILTER CARE AND CLEANING" section on page 42.)
4. Press the power ON-OFF button to ON.
If the TEMPERATURE WARNING indicator still continues to flash, call Boxlight at 1-800-762-5757 or 360-
779-7901.
NOTE: The Cooling Fan may work for cooling while the projector is turned off. When the Cooling
Fan is working, TEMPERATURE WARNING INDICATOR flashes red.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC OPERATION
ADJUSTING THE IMAGE
ZOOM ADJUSTMENT
Press the ZOOM button on the Top Control or the ZOOM ▲/▼
button on the Remote Control Unit to turn into the ZOOM
mode.
1
2
Press the POINT UP button or the ZOOM ▲ button to have the
image larger, and press the POINT UP button or the ZOOM ▼
button to have the smaller.
Zoom
In the Computer mode, the image can be expanded, compressed,
and panned with the Digital Zoom function. Refer to page 29, 37 for
the Digital Zoom operation.
The message disappears after 4 seconds.
FOCUS ADJUSTMENT
Press the FOCUS button on the Top Control or the FOCUS
▲/▼ button on the Remote Control Unit to turn into the FOCUS
mode.
1
2
Adjust the focus of the image by pressing the POINT
UP/DOWN button or the FOCUS ▲/▼ button.
Focus
The message disappears after 4 seconds.
KEYSTONE ADJUSTMENT
If the picture obtained keystone distortion, correct screen with KEYSTONE adjustment.
Press the KEYSTONE ▲/▼ button on the Remote Control Unit
or select the Keystone on the SCREEN menu. (Refer to page
29, 30, 37.) The message “Keystone” is displayed.
1
Keystone
Correct the Keystone distortion by pressing the KEYSTONE
▲/▼ button or the POINT UP/DOWN button(s). Press the
KEYSTONE ▲ button or the POINT UP button to reduce the
upper part or the image, and press the KEYSTONE ▼ button or
the POINT DOWN button to reduce the lower part.
2
The message disappears after 4 seconds.
Reduce the upper width with the KEY STONE ▲
button or the POINT UP button.
Reduce the lower width with the KEY STONE ▼
button or the POINT DOWN button.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC OPERATION
NO SHOW FUNCTION
Press the NO SHOW button on the Remote Control Unit to turn the
picture into black image. This function is cancelled when the NO
SHOW button is pressed again or any other function button is
pressed.
No show
The message disappears after 4 seconds.
PICTURE FREEZE FUNCTION
Press the FREEZE button on the Remote Control Unit to freeze the picture on screen. This function is cancelled when
the FREEZE button is pressed again or any other function button is pressed.
SOUND ADJUSTMENT
It indicates the level of the volume.
SOUND VOLUME ADJUSTMENT
Press the VOLUME (+/–) button(s) on the Top Control or on the
Remote Control Unit to adjust the volume. The Volume dialog box
appears on the screen for a few seconds.
The VOLUME (+) button to increase the volume, and The VOLUME
(–) button for decreasing.
Press the MUTE button to set
the Mute function On or Off.
SOUND MUTE ADJUSTMENT
The display disappears after 4 seconds.
Press the MUTE button on the Remote Control Unit to cut off the
sound. To restore the sound to its previous level, press again or
press Volume button(s).
22
Download from Www.Somanuals.com. All Manuals Search And Download.
COMPUTER MODE
SELECTING COMPUTER MODE
COMPUTER / MCI
DIRECT OPERATION
button
MODE button
COMPUTER
COMPUTER
Select COMPUTER mode by pressing the MODE button on the Top
Control or the COMPUTER / MCI button on the Remote Control Unit.
MCI
MCI
VIDEO
MENU OPERATION
Press the MENU button and the ON-SCREEN MENU will appear.
Press the POINT LEFT/RIGHT buttons to select Computer
press the SELECT button.
and
CURRENT MODE DISPLAY
When selecting the Computer Mode, the Current Mode display
appears. It shows the information of the computer of the mode
selected.
Providing the information of the computer detected
by the projector.
SELECTING COMPUTER SYSTEM
AUTOMATIC MULTISCANNING SYSTEM
This projector automatically tunes to most different types of computer
based on VGA, SVGA or XGA (refer to “COMPATIBLE COMPUTER
SPECIFICATION” on page 26). When selecting Computer, this
projector automatically tunes to the incoming signal and projects the
proper image without any special setting. (Setting of the Computer
System may be required when connecting some computers.)
SYSTEM BOX
Note : The projector may provides the messages below.
It displays the SYSTEM
being selected.
The projector cannot discriminate or detect the
input signal from the computer. Adjust and set the
computer system manually. (Refer to page 24.)
Go to PC adj.
There is no signal input from the computer. Make
sure the connection of the computer and the
No signal
projector is set correctly.
TROUBLESHOOTING on page 44.)
(Refer to
The system being selected.
SELECT COMPUTER SYSTEM MANUALLY
To set the Computer system manually, select the mode on the ON-
SCREEN MENU.
Press the MENU button and the ON-SCREEN MENU will
appear. Press the POINT LEFT/RIGHT buttons to select
SYSTEM and press the SELECT button. Another dialog box
COMPUTER MODE Menu will appear.
1
The systems on this
dialog box can be
selected.
Press the POINT DOWN button and a red-arrow icon will
appear. Move the arrow to the system that you want to set,
2
and then press
SELECT button.
It closes the
SYSTEM Menu.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
COMPUTER MODE
PC ADJUSTMENT
This Projector can automatically tune to the display signals from most personal computers currently distributed.
However, some computers employ the special signal formats which are different from the standard ones and
may not be tuned by Multiscanning of this projector. If this happens, the projector cannot reproduce a proper
image and the image is recognized as a flickering picture, a non-synchronized picture, a non-centered picture or
a skewed picture.
This projector has PC ADJUSTMENT function, to enable you to precisely adjust several parameters to match
with those exceptional signal formats and the projector has five independent memory areas to memorize those
parameters manually adjusted. This enables you to recall the setting for a specific computer whenever you use
it.
Press the MENU button and the ON-SCREEN MENU will
appear. Press the POINT RIGHT/LEFT buttons to select PC
1
ADJUST
and press the SELECT button. Another dialog
box “Where to reserve” Menu will appear.
In this dialog box, you can store the parameter into the area
from “Mode 1” to “Mode 5.” When memorizing the new
computer parameter, select the Mode with the message of
“Free” by pressing the POINT UP/DOWN buttons and the
SELECT button. To change the parameters of the Mode
previously set, select the Mode with “Stored.”
2
3
This Mode has
parameters being
stored.
When the Mode is selected, Parameter adjustment dialog box
appears. Move the arrow to the item that you want to change
by pressing the POINT UP/DOWN buttons, and adjust the each
item to match with your computer. To change the value, press
either the POINT RIGHT button or the POINT LEFT button.
Refer to the next page for adjusting each item.
The Vacant Mode.
Manual set Computer
Mode (1 to 5).
It closes the PC
ADJUSTMENT Menu.
Move the arrow to “Stored” and press the SELECT button. The
parameter is memorized in the selected Mode.
4
5
To activate the Mode manually adjusted in this PC
ADJUSTMENT Menu, select the Mode at the SYSTEM
SELECT Menu. (Refer to page 23.)
Press the POINT
RIGHT/LEFT
button(s) to
adjust the value.
Press the
SELECT button
to set Full screen
function on/off.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Total lines
The number of the total vertical lines. Adjust the number to match
the image of your personal computer.
Total dots
The number of the total dots in one horizontal period. Adjust the
number to match the image of your personal computer.
Horizontal / Vertical
Adjustment of the horizontal or vertical |picture position. When the
image is not centered on the screen, adjust each of those items.
Clamp
Press the
SELECT button
to select the
typical resolution
of the image.
Adjustment of the clamp level. When the image has a dark bar(s),
try this adjustment.
Display area
Adjustment of the area displayed with this projector. Select the
resolution at the Display area dialog box, or adjust the number at
the column of “H” or “V” to match the resolution of the image.
Full Screen
Set “On” to resize the image with 4 x 3 aspect ratio to fit the
screen.
Each of the keys operates as follow.
Reset
Recalls the parameter data that previously
adjusted.
Mode free
Clears the parameter data previously set in the
selected Mode.
Stored
Quit
Stores the parameters in the memory.
Closes the PC ADJUST Menu.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
COMPUTER MODE
COMPATIBLE COMPUTER SPECIFICATIONS
Basically this projector can accept the signal from all computers with the V, H-Frequency below mentioned
and less than 135 MHz of Dot Clock.
ON-SCREEN
DISPLAY
ON-SCREEN
DISPLAY
H-Freq.
(kHz)
V-Freq.
(Hz)
H-Freq.
(kHz)
V-Freq.
(Hz)
RESOLUTION
RESOLUTION
VGA 1
VGA 2
640 x 480
720 x 400
640 x 400
640 x 480
640 x 480
640 x 480
640 x 480
640 x 480
31.47
31.47
31.47
37.86
37.86
37.50
34.97
35.00
15.734
15.625
35.156
37.88
46.875
53.674
48.08
37.90
34.50
38.00
38.60
59.88
70.09
70.09
74.38
72.81
75.00
66.60
66.67
30
SVGA 10
SVGA 11
SVGA 12
MAC1 6
XGA 1
800 x 600
800 x 600
800 x 600
832 x 624
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
47.90
32.70
38.00
49.72
48.36
68.677
60.023
56.476
60.31
48.50
44.00
63.48
36.00
62.04
61.00
35.522
46.90
47.00
60.24
71.92
51.09
60.51
74.55
60.00
84.997
75.03
70.07
74.92
60.02
54.58
79.35
43.59
77.07
75.70
43.48
58.20
58.30
75.08
VGA 3
VGA 4
VGA 5
VGA 6
XGA 2
MAC LC13
MAC 13
RGB
XGA 3
XGA 4
640 x 480
(Interlace)
768 x 576
(Interlace)
XGA 5
RGB
25
XGA 6
SVGA 1
SVGA 2
SVGA 3
SVGA 4
SVGA 5
SVGA 6
SVGA 7
SVGA 8
SVGA 9
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
56.25
60.32
75.00
85.06
72.19
61.03
55.38
60.51
60.31
XGA 7
XGA 8
1024 x 768
(Interlace)
XGA 9
XGA 10
XGA 11
XGA 12
XGA 13
XGA 14
MAC 19
1024 x 768
1024 x 768
1024 x 768
(Interlace)
1024 x 768
1024 x 768
1024 x 768
NOTE : Specifications are subject to change without notice.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
COMPUTER MODE
PICTURE IMAGE ADJUSTMENT
ADJUST PICTURE IMAGE MANUALLY
Press the MENU button and the ON-SCREEN MENU will
appear. Press the POINT LEFT/RIGHT buttons to select
IMAGE and press the SELECT button. Another dialog box
1
2
PICTURE IMAGE ADJUSTMENT Menu will appear.
Press the POINT DOWN button and a red-arrow icon will
appear. Move the arrow to the item that you want to change by
pressing the POINT UP/DOWN buttons. To change the value,
press either the POINT RIGHT button or the POINT LEFT
button.
It indicates the
roughly level of
the item.
Fine sync.
Adjust the picture as necessary to eliminate flicker from the display.
(From 0 to 255.)
Total dots
Move the arrow to
the item and press
POINT RIGHT /
LEFT button.
The number of the total dots in one horizontal period. Adjust the
number to match your PC image.
White balance (Red / Green / Blue)
Move the arrow to Red, Green, or Blue that you want to adjust.
Press POINT LEFT button to adjust the color of image lighter, and
press POINT RIGHT button to adjust deeper. (From 0 to 63.)
Contrast
Close the PICTURE
IMAGE ADJUSTMENT
Menu.
Press POINT LEFT button to adjust the image lighter, and press
POINT RIGHT button to adjust deeper. (From 0 to 63.)
Brightness
Press POINT LEFT button to adjust the image darker, and press
POINT RIGHT button to adjust brighter. (From 0 to 63.)
Each of the keys operates as follow.
Reset
Stored
Quit
Recalls the data previously adjusted.
Stores the adjusted data in the memory.
Closes the PICTURE IMAGE ADJUSTMENT Menu.
NORMAL FUNCTION
The normal picture level is preset on this projector at the factory and
can be restored anytime you press the NORMAL button (located on
the Top Control or on the Remote Control Unit). The “Normal”
display will be displayed on the screen for a few seconds.
Normal
27
Download from Www.Somanuals.com. All Manuals Search And Download.
COMPUTER MODE
AUTO IMAGE FUNCTION
The Auto Image function is provided to automatically adjust Fine
sync., Total dots, and Picture Position for most computers.
Press the MENU button and the ON-SCREEN MENU will
appear. Press the POINT LEFT/RIGHT buttons to select
1
AUTO IMAGE
and press the SELECT button.
Another dialog box AUTO IMAGE Menu will appear.
Move the arrow to an item that you want to adjust by pressing
the POINT UP/DOWN button. Change the setting On or Off by
pressing the SELECT button.
2
Fine sync.
Adjust the picture as necessary to eliminate flicker from the display.
This item can be adjusted manually. (Refer to page 27.)
Total dots
The number of the total dots in one horizontal period. This item can
be adjusted manually. (Refer to page 27.)
It starts the adjustment
on the item set to "On".
Position
Move the arrow to
the item and then
press the SELECT
button.
Adjustment of the position of the image. This item can be adjusted
manually. (Refer to page 28.)
It terminates the PICTURE
IMAGE ADJUSTMENT Menu.
Move the arrow to “Go!” and press the SELECT button to start
the Auto Image function.
This adjustment can be executed by pressing AUTO IMAGE
button on the Top Control and the Remote Control Unit.
3
Stored
Stores the On/Off setting of each item.
Starts the Auto Image Adjustment.
Go!
Quit
Closes the AUTO IMAGE ADJUSTMENT Menu.
NOTE : The Fine sync., Total dots, and Picture Position of some
computers may not be fully adjusted with the Auto Image
Function. In that case, manual adjustment is required to
make fine image. (Refer to page 27 to adjust "Fine sync." or
"Total dots" and page 28 to adjust Picture Position.)
PICTURE POSITION ADJUSTMENT
The position of the image can be adjusted vertically and horizontally through PICTURE POSITION
ADJUSTMENT.
Press the MENU button and the ON-SCREEN MENU will
appear. Press the POINT LEFT/RIGHT buttons to select
1
POSITION
and press the SELECT button. The PICTURE
POSITION dialog box will appear.
Move the image by pressing the POINT UP / DOWN / RIGHT /
LEFT buttons.
PICTURE POSITION
dialog box
2
Press the POINT UP
/
DOWN / RIGHT / LEFT
buttons to move the image
To cancel POSITION mode, press the any buttons except SELECT,
RIGHT CLICK, POINT, PAGE ▲/▼ or LASER button. To recall the
position previously adjusted, press NORMAL button.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
COMPUTER MODE
PICTURE SCREEN ADJUSTMENT
This projector has a picture screen resize function, which enables you to display the image in desirable size.
Press the MENU button and the ON-SCREEN MENU will
appear. Press the POINT LEFT/RIGHT buttons to select
1
SCREEN
and press the SELECT button. Another dialog
box PICTURE SCREEN Menu will appear.
Press the POINT DOWN button and a red-arrow icon will
appear. Move the arrow to the function that you want to select
and then press SELECT button.
2
True
Move the arrow to the
function and press the
SELECT button.
To turn the image into its original size select True in the dialog box.
When the original image size is larger than the screen size (800 x
600), this projector becomes Digital Zoom mode automatically.
Keystone
When the image is distorted vertically, select Keystone in the dialog
box. The ON-SCREEN menu and SCREEN ADJUST menu
disappears and the message “Keystone” is displayed. Correct the
Keystone distortion by pressing the KEYSTONE ▲/▼ button or the
POINT UP/DOWN button(s). Refer to KEYSTONE ADJUSTMENT
on page 21.
Digital Zoom
To adjust the image size or pan the image, select Digital zoom in
the dialog box. The ON-SCREEN menu and SCREEN ADJUST
menu disappears and the message “D. Zoom” is displayed.
This projector is also turned into Digital Zoom mode by pressing
the D.ZOOM ▲/▼ button on the Remote Control Unit.
Refer to the following for operation.
Expand function
To expand the image size, press the D.ZOOM ▲ button or the SELECT button.
Compress function
To compress the image size, press the D.ZOOM ▼ button or the RIGHT CLICK button. The size of image is reduced by
degrees.
Panning function
To pan the image, press the POINT UP/DOWN/LEFT/RIGHT buttons. Panning function can work only when the image
is larger than the screen size.
To cancel Digital Zoom mode, press the any buttons except D.ZOOM ▲/▼, SELECT, RIGHT CLICK, POINT, PAGE
▲/▼ or LASER button. To adjust the image to the screen size (800 x 600), press NORMAL button.
● This projector cannot display in the resolution higher than 1024 X 768. If your computer’s screen resolution is higher
than 1024 X 768, reset the resolution to the lower before connecting the projector.
● The image data in other than SVGA (800 x 600) is modified to fit the screen size in the initial mode.
● The normal "Panning Operation" may not function properly if the computer system prepared with the "PC Adjust" is
used.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
VIDEO MODE
SELECTING VIDEO MODE
MODE button
COMPUTER
DIRECT OPERATION
Select VIDEO mode by pressing the MODE button on the Top
Control or the VIDEO button on the Remote Control Unit.
MCI
VIDEO
MENU OPERATION
Press the MENU button and the ON-SCREEN MENU will appear.
Press the POINT LEFT/RIGHT buttons to select Video
press the SELECT button.
and
SELECTING COLOR SYSTEM
Press the MENU button and the ON-SCREEN MENU will
This box indicates the
system being selected.
1
2
appear. Press the POINT LEFT/RIGHT buttons to select
SYSTEM and press the SELECT button. Another dialog box
VIDEO SYSTEM Menu will appear.
Press the POINT DOWN button and a red-arrow icon will
appear. Move the arrow to "Auto", and then press the
SELECT
button.
Auto
The projector automatically detects the incoming Video system, and
adjusts itself to optimize its performance.
When the Video System is PAL-M or PAL-N, select the system
manually.
Move the arrow to
the Mode and press
the SELECT button.
PAL / SECAM / NTSC / NTSC4.43 / PAL-M / PAL-N
If the projector cannot reproduce the proper video image, it is
required to select a specific broadcast signal format among PAL,
SECAM, NTSC, NTSC 4.43, PAL-M, or PAL-N.
PICTURE SCREEN ADJUSTMENT
This projector has a picture screen resize function, which enables you to display the image in desirable size.
Press the MENU button and the ON-SCREEN MENU will
appear. Press the POINT LEFT/RIGHT buttons to select
1
SCREEN
and press the SELECT button. Another dialog
box PICTURE SCREEN ADJUSTMENT DISPLAY will appear.
Press the POINT DOWN button and a red-arrow icon will
appear. Move the arrow to the screen size that you want to
2
set, and then press the
SELECT button.
Regular
Normal Video Image size with 4 x 3 aspect ratio.
Move the pointer to the function that and
press the SELECT button.
Wide
Resizes the image for wide screen size with 16 x 9 aspect ratio.
Keystone
When the image is distorted vertically, select Keystone in the dialog
box. Correct the Keystone distortion by pressing KEYSTONE ▲/▼
button or POINT UP/DOWN button(s). Refer to KEYSTONE
ADJUSTMENT on page 21.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
VIDEO MODE
PICTURE IMAGE ADJUSTMENT
ADJUSTING THE PICTURE IMAGE
Press the MENU button and the ON-SCREEN MENU will
appear. Press the POINT LEFT/RIGHT buttons to select
IMAGE and press the SELECT button. Another dialog box
1
2
PICTURE IMAGE ADJUSTMENT Menu will appear.
Press the POINT DOWN button and a red-arrow icon will
appear. Move the arrow to the item that you want to adjust by
pressing the POINT UP/DOWN buttons. To change the value,
press either the POINT RIGHT button or the POINT LEFT
button.
Color
It indicates the
roughly level of
the item.
Press POINT LEFT button to adjust the image lighter, and press
POINT RIGHT button to adjust deeper. (From 0 to 63.)
Move the arrow to
the item and press
POINT RIGHT /
LEFT button.
Tint
Press POINT LEFT button to adjust the color more purple, and
press POINT RIGHT button to adjust more green. (From 0 to 63.)
White balance (Red / Green / Blue)
Move the arrow to Red, Green, or Blue that you want to adjust.
Press POINT LEFT button to adjust the color of image lighter, and
press POINT RIGHT button to adjust deeper. (From 0 to 63.)
Contrast
It closes the PICTURE
IMAGE ADJUSTMENT
Menu.
Press POINT LEFT button to adjust the image lighter, and press
POINT RIGHT button to adjust deeper. (From 0 to 63.)
Brightness
Press POINT LEFT button to adjust the image darker, and press
POINT RIGHT button to adjust brighter. (From 0 to 63.)
Sharpness
Press POINT LEFT button to adjust the image softer, and press
POINT RIGHT button to adjust sharper. (From 0 to 63.)
Each of the keys operates as follow.
Reset
Stored
Quit
Recalls the data previously adjusted.
Stores the data in the memory.
Closes the PICTURE IMAGE ADJUSTMENT Menu.
NORMAL FUNCTION
The normal picture level is preset on this projector at the factory and
can be restored anytime you press the NORMAL button (located on
the Top Control or on the Remote Control Unit). The "Normal"
display will be displayed on the screen for a few seconds.
Normal
31
Download from Www.Somanuals.com. All Manuals Search And Download.
MCI MODE
OPERATING THE PC CARD SLOT
This projector has PC CARD SLOT and the pictures in a memory card (SmartMedia with PC Card Adapter or
PC card) can be displayed just by inserting the card into it. It is unnecessary to connect with other input
equipment. Media Card Imager (supplied with CD-ROM) can edit the image data and record it into a memory
card for projecting with the projector.
PC with Windows 95
Media Card Imager
(CD-ROM)
MC I
PC Card
(not supplied)
Digital Camera
SmartMedia with PC Card Adapter
(supplied)
PC CARD SLOT (Front)
HOW TO LOAD THE MEMORY CARD INTO THE PROJECTOR
LOAD
PC CARD SLOT
Insert PC Card Adapter (with SmartMedia) or PC card into PC CARD
SLOT. Make sure EJECT button pops out.
NOTE : Be sure to insert the memory card with the front side to the
left side of the projector. Do not insert the card in the
reverse. The card may be damaged.
Memory Card
Insert with the front side of the card
to the left side of the projector.
UNLOAD
Press EJECT button, and the memory card pops out.
NOTE : Do not take the card out while the PC CARD SLOT loading.
Data and the card can be damaged.
PC CARD INDICATOR
WHEN THIS INDICATOR IS LIGHTING, THE
PROJECTOR IS READING OR WRITING THE
DATA INTO THE MEMORY CARD. DO NOT
REMOVE THE MEMORY CARD. DATA IN
THE MEMORY CARD MAY BE DAMAGED.
EJECT BUTTON
32
Download from Www.Somanuals.com. All Manuals Search And Download.
AVAILABLE DATA
This projector can project the image data as follow through PC
CARD SLOT.
● The data edited by “Media Card Imager.”
● The data of the resolution between VGA (640 X 480) and XGA
(1024 X 768) in Bit Map type (BMP) or JPEG type (JPG), such as
Digital Camera data, can be also displayed.
(Some image data in XGA size may not be displayed properly. In
that case, reset the resolution to the lower.)
Media Card Imager
Media Card Imager (CD-ROM) is attached
to this projector to edit the image data for
projecting. Installation of Media Card
Imager is recommended. Refer to
Owner’s Manual of Media Card Imager for
installation and operation.
Refer to “SHOW THE DATA IN THE MEMORY CARD” on page 34
to display the image data.
AVAILABLE CARD
SmartMedia (with PC Card Adapter) or Type || PCMCIA-ATA Card can be used with this projector. (Those memory cards
are supplied with this projector.)
Refer to SMARTMEDIA AND PC CARD ADAPTER on pages 38 and 39 for operation.
NOTE : Some PCMCIA Adapter or PC Card is not available for this projector and cannot provide the image data. In that
case, use our SmartMedia and PC Card Adapter.
SELECTING MCI MODE
When the memory card is inserted into PC CARD SLOT, mode is automatically set to MCI mode and the first
Page of the latest Index is projected on the screen. To turn Video/Computer mode to MCI mode manually,
operate as follows.
COMPUTER / MCI
DIRECT OPERATION
button
MODE button
COMPUTER
Select MCI mode by pressing the MODE button on the Top Control
or the COMPUTER / MCI button on the Remote Control Unit.
COMPUTER
MCI
MCI
VIDEO
MENU OPERATION
Press the MENU button and the ON-SCREEN MENU will appear.
Press the POINT LEFT/RIGHT buttons to select MCI
the SELECT button.
and press
33
Download from Www.Somanuals.com. All Manuals Search And Download.
MCI MODE
SHOW THE DATA IN THE MEMORY CARD
BASIC OPERATION
Insert the memory card and turn the projector into MCI mode.
The image in the memory card is displayed.
1
2
Select the Index
To change the image to others, press the PAGE ▲ or ▼
button. (When the “Display Timer” is set in the image with the
Media Card Imager, the image is changed to another
automatically.)
Index
To select Index or Page in the table, follow the instructions of
INDEX SELECTION and PAGE SELECTION.
Pages in the Index
Index and Page
The data edited with Media Card Imager is the Index format
consisting of several Pages. To project the desirable image,
select the Index and then select the Page in the Index.
● This projector can project only the image data in Bit Map type or in JPEG type or the data edited by Media Card Imager
(supplied) through the PC CARD SLOT. Other data is not available and should be edited and written in a memory card
with Media Card Imager before loading PC CARD SLOT.
(The data in Bit Map type or in JPEG type, such as the data captured with a digital camera, can be projected directly
through PC CARD SLOT.)
● If there are the data edited by Media Card Imager and other data (such as in Bit Map type or JPEG type) together in
one memory card, the data edited by Media Card Imager has a priority to be projected with the LCD projector. The
other image data in Bit Map type or JPEG type is not projected. In that case, edit those data and write in the memory
card with the Media Card Imager.
INDEX SELECTION
Press the MENU button and the ON-SCREEN MENU will
appear. Press the POINT LEFT/RIGHT buttons to select VIEW
and press the SELECT button. Another dialog box VIEW
SETTING menu will appear.
1
Press the POINT DOWN button and a red-arrow icon will
appear. Move the arrow to "Index", and then press the
2
The table of Indexes in the memory card will
SELECT button.
appear.
Press the POINT UP/DOWN/LEFT/RIGHT buttons to move to
the Index that you want to project and press the SELECT
button. The first Page of the Index selected is displayed.
(Press SELECT button again to display the table of Pages.)
Move the arrow to
each operation and
press the SELECT
button.
3
PAGE SELECTION
Press the MENU button and the ON-SCREEN MENU will
appear. Press the POINT LEFT/RIGHT buttons to select VIEW
and press the SELECT button. Another dialog box VIEW
SETTING menu will appear.
1
2
3
Press the POINT DOWN button and a red-arrow icon will
appear. Move the arrow to "Page", and then press the
The table of pages of the index card will
SELECT button.
appear.
Press the POINT UP/DOWN/LEFT/RIGHT buttons to move to
the Page that you want to project and press the SELECT
button. The page selected is displayed on the screen.
The table of Pages can be displayed by pressing the SELECT
button when the page is displayed on full screen.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
MCI MODE
WRITE DATA INTO THE MEMORY CARD
The data edited by Media Card Imager in the computer can be written in or read from the memory card with the
PC Card drive of your Personal Computer or the PC CARD Slot of this projector.
The data edited by Media Card Imager is written in Bit Map type (BMP) or JPEG type (JPG).
ACCESS TO THE MEMORY CARD THROUGH THE PROJECTOR
If your computer doesn't have the PC card writing equipment, the data can be written or read by connecting
with this projector.
NOTE : This operation can be made only by Media Card Imager in the Personal Computer.
Connect the projector to the Personal Computer with the
Control Cable for Serial Port (optionally supplied / refer
to page 12, 13).
Connect the projector to your computer with the Control Cable
for Serial Port (optionally supplied). (Refer to “CONNECTING
COMPUTER” on Page 12, 13.)
1
Insert the memory card into PC CARD SLOT of the projector.
And then, turn on the projector first and the computer.
Press the MENU button and the ON-SCREEN MENU will
appear. Press the POINT LEFT/RIGHT buttons to select View
and press the SELECT button. Another dialog box VIEW
SETTING Menu will appear.
2
Press POINT DOWN button and a red arrow appear. Move the
arrow to Card access by pressing POINT UP/DOWN button.
And then press SELECT button. “Ready to access” is
press the SELECT
displayed.
Move the arrow to
each operation and
3
button.
Operate Media Card Imager of your computer to write/read the
data in the PC card. (Refer to Owner's Manual of Media Card
Imager for operation.)
NOTE : Connect the projector to the computer with Control Cable
before turning those appliances on.
Do not press any button while read/write the data through
PC CARD Slot of the projector. Those operations are
canceled and the data in the memory card may be
damaged.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
MCI MODE
PICTURE IMAGE ADJUSTMENT
ADJUST THE PICTURE IMAGE MANUALLY
Press the MENU button and the ON-SCREEN MENU will
appear. Press the POINT LEFT/RIGHT buttons to select
IMAGE and press the SELECT button. Another dialog box
1
2
PICTURE IMAGE ADJUSTMENT Menu will appear.
Press the POINT DOWN button and a red-arrow icon will
appear. Move the arrow to the item by pressing the POINT
UP/DOWN buttons. To change the value press either the
POINT RIGHT button or the POINT LEFT button.
It indicates the rough-
ly level of the item.
White balance (Red / Green / Blue)
Move the arrow to Red, Green, or Blue that you want to adjust.
Press POINT LEFT button to adjust the color of image lighter, and
press POINT RIGHT button to adjust deeper. (From 0 to 63.)
Move the arrow to
the item and press
POINT RIGHT /
LEFT button.
Contrast
Press POINT LEFT button to adjust the image lighter, and press
POINT RIGHT button to adjust deeper. (From 0 to 63.)
Close the PICTURE
IMAGE ADJUSTMENT
Menu.
Brightness
Press POINT LEFT button to adjust the image darker, and press
POINT RIGHT button to adjust brighter. (From 0 to 63.)
Each of the keys operates as follow.
Reset
Stored
Quit
Recalls the data previously adjusted.
Stores the adjusted data in the memory.
Closes the PICTURE IMAGE ADJUSTMENT Menu.
NORMAL FUNCTION
The normal picture level is preset on this projector at the factory and
can be restored anytime you press the NORMAL button (located on
the Top Control or on the Remote Control Unit). The "Normal"
display will be displayed on the screen for a few seconds.
Normal
PICTURE POSITION ADJUSTMENT
The position of the image can be adjusted vertically and horizontally through PICTURE POSITION
ADJUSTMENT.
Press the MENU button and the ON-SCREEN MENU will
appear. Press the POINT LEFT/RIGHT buttons to select
1
POSITION
and press the SELECT button. The PICTURE
POSITION dialog box will appear.
PICTURE POSITION
dialog box
Move the image by pressing the POINT UP / DOWN / RIGHT /
LEFT buttons.
2
Press the POINT UP
/
DOWN / RIGHT / LEFT
buttons to move the image
To cancel POSITION mode, press the any buttons except SELECT,
RIGHT CLICK, POINT, AUTO IMAGE, PAGE ▲/▼ or LASER button.
To recall the position previously adjusted, press NORMAL button.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
MCI MODE
PICTURE SCREEN ADJUSTMENT
This projector has a picture screen resize function, which enables you to display the image in desirable size.
Press the MENU button and the ON-SCREEN MENU will
appear. Press the POINT LEFT/RIGHT buttons to select
1
SCREEN
and press the SELECT button. Another dialog
box PICTURE SCREEN Menu will appear.
Press the POINT DOWN button and a red-arrow icon will
appear. Move the arrow to the function that you want to select
and then press SELECT button.
2
True
To turn the image into its original size select True in the dialog box.
When the original image size is larger than the screen size (800 x
600), this projector becomes Digital Zoom mode automatically.
Move the arrow to the
function and press the
SELECT button.
Keystone
When the image is distorted vertically, select Keystone in the dialog
box. The ON-SCREEN menu and SCREEN ADJUST menu
disappears and the message “Keystone” is displayed. Correct the
Keystone distortion by pressing KEYSTONE ▲/▼ button or POINT
UP/DOWN button(s). Refer to KEYSTONE ADJUSTMENT on
page 21.
Digital Zoom
To adjust the image size or pan the image, select Digital zoom in
the dialog box. The ON-SCREEN menu and SCREEN ADJUST
menu disappears and the message “D. Zoom” is displayed.
This projector is also turned into Digital Zoom mode by pressing
D.ZOOM ▲/▼ button on the Remote Control Unit.
Refer to the following for operation.
Expand function
To expand the image size, press D.ZOOM ▲ button or SELECT button. The image is magnified by degrees.
Compress function
To compress the image size, press D.ZOOM ▼ button or RIGHT CLICK button. The size of image is reduced by
degrees.
Panning function
To pan the image, press POINT UP/DOWN/LEFT/RIGHT buttons. Panning function can work only when the image is
larger than the screen size.
To cancel Digital Zoom mode, press the any buttons except D.ZOOM ▲/▼, SELECT, RIGHT CLICK, POINT, PAGE
▲/▼, AUTO IMAGE, or LASER button. To adjust the image to the screen size (800 x 600), press NORMAL button.
● This projector cannot display in the resolution higher than 1024 X 768. If your computer’s screen resolution is higher
than 1024 X 768, reset the resolution to the lower before connecting the projector.
● The image data in other than SVGA (800 x 600) is modified to fit the screen size in the initial mode.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
MCI MODE
SMARTMEDIA AND PC CARD ADAPTER
SmartMedia and PC Card Adapter are provided with this LCD projector. SmartMedia can be used as a PC card
conforming to the PC Card Standard-ATA by combining with PC Card Adapter.
INSTALL / REMOVE THE SMARTMEDIA
INSTALL
PC Card Adapter
(supplied)
Insert SmartMedia fully into PC Card Adapter. Make sure EJECT
button pops out.
NOTE : The front side of SmartMedia has Contact Area on its
surface.
SmartMedia
(supplied)
The front side of PC Card Adapter has Eject button on the
left side of the slot.
Do not insert SmartMedia in the reverse. The card and the
data can be damaged.
REMOVE
To remove SmartMedia, fully press in the EJECT button. The card
pops out, then take out the card.
NOTE : Do not pull SmartMedia by force. It may damage
SmartMedia or PC Card Adapter.
EJECT button
IMPORTANT NOTE
THE DATA STORED ON THE MEMORY CARD (SMARTMEDIA OR PC CARD) MAY BE DAMAGED OR
LOST BECAUSE OF THE DAMAGE OF THE MEMORY CARD OR THE ACCIDENTAL ERASURE. IT IS
RECOMMENDED THAT ANY IMPORTANT DATA SHOULD BE COPIED ONTO SEPARATE MEDIA,
SUCH AS A FLOPPY DISK, A HARD DISK, OR A MO DISK. WE SHALL NOT BE LIABLE FOR ANY
DAMAGE OR LOSS OF PROFITS ARISING FROM THE LOSS OF DATA BECAUSE OF THE ACCIDEN-
TAL OPERATION AND THE DAMAGE OF A MEMORY CARD OR APPLIANCES. REFER TO OWNER’S
MANUAL OF MEDIA CARD IMAGER FOR OPERATING THE SOFTWARE.
38
Download from Www.Somanuals.com. All Manuals Search And Download.
MCI MODE
PRECAUTIONS AND SPECIFICATIONS OF THE SMARTMEDIA
● SmartMedia is a precision device. Do not bend it, drop it, subject it
to strong forces or shocks or place where strong static electrical
charge can be generated.
● Do not touch the surface of the Contact Area with fingers or allow it
to be stained with foreign materials. Store SmartMedia inside its
protective case when it is not used.
● SmartMedia is a consumable item. The data may not be written in
or read from SmartMedia by using for a long time. In that case,
replace SmartMedia with new one.
①Contact Area
Memory capacity : 8MB
Data is written in Contact Area. Never
scratch or stain this area.
Operating voltage : 3.3 V DC
Usage environment
➁ Write Protect Area
Temperature : 0~55 °C (during use)
-20~65 °C (during storage)
Humidity : less than 95% (during use, during storage)
Affix Write Protect Sticker onto Write
Protect Area to prevent from accidental
erasure.
CAUTION
➂ Index Area
Write Protect Sticker is not available for PC. When PC attempts
to read the data from SmartMedia with Write Protect Sticker, it pro-
vides the error messages or the control of PC becomes insecure
because of the property of the interface. When the error messages
are displayed, press any key to return to the normal display. It is
recommended, however, SmartMedia should be used on PC with-
out Write Protect Sticker.
Affix Index Label onto Index Area.
PRECAUTIONS AND SPECIFICATIONS OF THE PC CARD ADAPTER
● Do not bend it, drop it, subject it to strong forces or shocks or place
where strong static electrical charge can be generated.
● Do not insert materials other than SmartMedia. The adapter may
be damaged. Store PC Card Adapter inside its protective case
when it is not used.
● Do not shake the adapter, turn off the appliances, or remove
SmartMedia from the PC Card Adapter during writing or reading
data. It may damage the data in SmartMedia.
Operating voltage : 5 V DC
Usage environment
Temperature : 0~55 °C (during use)
-20~65 °C (during storage)
Humidity : less than 95%
(during use, during storage)
This adapter can be adapted to only our SmartMedia indicated below.
Available SmartMedia : 3.3V / 5V, 2MB / 4MB / 8MB /16MB
39
Download from Www.Somanuals.com. All Manuals Search And Download.
SETTING
SETTING MENU
Press the MENU button and the ON-SCREEN MENU will
appear. Press the POINT LEFT/RIGHT buttons to select
SETTING and press the SELECT button. Another
dialog box SETTING Menu will appear.
1
2
Press the POINT DOWN button and a red-arrow icon will
appear. Move the arrow to the item that you want to set, and
then press the
SELECT button to set it "On" or "Off".
When this function is in the "On" position, this projector
will produce a blue image instead of the video noise on
the screen when all the input source is unplugged or
turned off.
Blue back
When this function is in the "On" position, the On-
Screen Displays always appear when adjustments are
made. (The following displays disappear by switching
this function "Off.")
Display
Set the Pointer to the item,
and then press the SELECT
button.
● Preparation Display
(The Number-counting-down Display)
● Mode Display
● Volume/Mute Display
● Zoom Display
● Focus Display
● Normal Display
● No show Display
● Keystone Display
● D.Zoom Display
Ceiling function
Rear function
When this function is in the “On” position, the top /
bottom and the left / right reversed picture is provided
to project the image from a ceiling mounted projector.
Ceiling
Rear
When this function is in the “On” position, the left / right
reversed picture is provided to project the image to a
rear projection screen.
Turn this function “On” position in the SETTING menu.
The picture will change into next one by sliding black
image side ways like drawing the black curtains when
the input source is turned into another one.
Split wipe
The Lamp age function is designed to reset the lamp
replacement monitor timer. When replacing the lamp,
reset the lamp replacement monitor timer by using this
function. (Refer to page 43.)
Lamp age
SELECTING LANGUAGE
The language used in the ON-SCREEN MENU is selectable from
among English, German, French, Italian, Spanish and Japanese.
Press the MENU button and the ON-SCREEN MENU will
appear. Press POINT LEFT/RIGHT buttons to select
LANGUAGE and press the SELECT button. Another dialog
box LANGUAGE Menu will appear.
1
Move the Pointer to the
language that you want
to set, and then press
the SELECT button.
Press the POINT DOWN button and a red-arrow icon will
appear. Move the arrow to the language that you want to set,
2
and then press the
SELECT button.
40
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
OPERATING WIRELESS MOUSE
The Wireless Remote Control Unit is not only able to operate the projector but also usable as a wireless mouse
for most Personal Computers. The POINT buttons and the two CLICK buttons are used for the wireless mouse
operation.
The wireless mouse is usable when PC mouse pointer is displayed on the screen. When the menu or the
indicator of the projector is displayed on the screen instead of the PC mouse pointer, the wireless mouse cannot
be used.
INSTALLATION
To use the Wireless Remote Control Unit as the Wireless Mouse for a Personal Computer, installation of the
mouse driver (not supplied) is required. Make sure that the mouse driver is properly installed in your
computer. And make sure that the mouse port of the computer connected to Control Port is activated.
Connect the mouse port of your computer to the Control Port of
the projector with the Control Cable. (Refer to page 10 to 13 for
connection.)
1
Note : When the computer has no
mouse port, connect the Serial
Port of the computer to Control
Port of the projector with the
Control Cable for Serial Port.
Turn the projector on first, and then turn on your computer.
When the computer is switched on first, the Wireless Mouse
may not work properly.
2
OPERATING WIRELESS MOUSE
When controlling the pointer of the computer, operate the Wireless Mouse with POINT button, SELECT
button, and RIGHT CLICK button on the Wireless Remote Control Unit.
POINT button (Move the pointer)
POINT button
Used to move the pointer. The pointer is moved corresponding with
the direction you are pressing.
SELECT (LEFT CLICK) button
This button has the same function as the left button in a PC mouse.
RIGHT CLICK button
This button has the same function as the right button in a PC mouse.
Pressing this button does not affect any operation when in Menu
mode.
SELECT button
(left button of the
mouse)
RIGHT CLICK button
(right button of the mouse)
41
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
MAINTENANCE
TEMPERATURE WARNING INDICATOR
The TEMPERATURE WARNING Indicator flashes red when the internal temperature of the projector exceeds
the normal temperature. The Indicator stops flashing when the temperature of the projector become normal.
When the TEMPERATURE WARNING Indicator continues to flash, check the item listed below.
The Ventilation slots of the projector may be blocked. In such an event, reposition the appliance so that the
ventilation slots are not obstructed.
1
Air filters are clogged with dust particles. Clean the air filters by following AIR FILTER CARE AND CLEANING
below.
2
If the TEMPERATURE WARNING Indicator remains on after performing the above checks, the Cooling Fans or the
Internal Circuits may be malfunctioning. In that case, call the Boxlight.
3
AIR FILTER CARE AND CLEANING
The Removable Air Filters prevent dust from accumulating on the surface of the Projection Lens and the
Projection Mirror. Should the Air Filters become clogged with dust particles, it will reduce the Cooling Fans'
effectiveness and may result in internal heat build up and adversely affect on the life of the projector.
Clean the Air Filters following the steps below:
Turn the power off, and disconnect the AC power cord from the
AC outlet.
AIR FILTERS
1
Turn the projector upside down and remove 2 Air Filters by
pulling the latches of them upward.
2
Clean the Air Filters with brush or wash out the dust and
particles.
3
Replace the Air Filter. Make sure that the Air Filters are fully
inserted.
4
CAUTION
Do not operate the projector with the Air Filter removed.
The dust is stuck on the LCD Panel and the Mirror, and it
may spoil the fine picture image.
Do not put the small parts into the Air Intake Vents. It result
in the malfunction of the projector.
The Air Filter is small part. Take care that children don’t eat
or swallow it.
RECOMMENDATION
We recommend to avoid dusty/smoky place for operating the projector. Using in dusty place may
cause the picture of poor quality.
When using under the dusty or smoky conditions, dust may accumulate on the liquid crystal panel and lens inside it, and
may resultantly be projected on the screen together with the picture.
When the above symptoms are noticed contact Boxlight at 1-800-762-5757 or 360-779-7901 for cleaning.
CLEANING THE PROJECTION LENS
Follow these steps to clean the projection lens:
Apply a non-abrasive camera lens cleaner to a soft, dry cleaning cloth. Avoid using an excessive amount of cleaner.
Abrasive cleaners, solvents or other harsh chemicals might scratch the lens.
1
Lightly wipe the cleaning cloth over the lens.
2
3
When you don't use the projector, replace the lens cover.
42
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
LAMP REPLACEMENT INDICATOR
When the life of the Lamp of this projector draws to an end, the LAMP REPLACEMENT indicator lights red.
When the image becomes dark or the color of the image become unnatural, replacement of the Lamp is
required.
LAMP REPLACEMENT
CAUTION
● For continued safety, replace with a lamp assembly of the same type.
● Allow the projector to cool for at least 45 minutes before you open the lamp cover. The inside of the projector
can become very hot.
● Do not drop the lamp assembly or touch the glass bulb! The glass can shatter and may cause injury.
Follow these steps to replace the lamp assembly.
Turn off the projector and disconnect the AC plug. Allow the
projector to cool for at least 45 minutes.
1
Remove a screw with a screwdriver and remove the Lamp
Cover.
2
Remove 2 screws with a screwdriver and pull out the Lamp
Assembly by grasping the handle.
3
LAMP COVER
Replace the Lamp Assembly with new one and tighten 2
screws. Make sure that the Lamp Assembly is set properly.
And replace the Lamp Cover and tighten a screw.
4
HANDLE
Connect the AC Power Cord to the projector and turn the
projector on.
5
6
Reset the Lamp Replacement Monitor Timer (refer to the
section “Lamp Replacement Monitor Timer” below).
NOTE : Do not reset the LAMP REPLACEMENT MONITOR
LAMP
ASSEMBLY
TIMER, when the lamp is not replaced.
ORDER REPLACEMENT LAMP
Replacement Lamp can be ordered through Boxlight at 1-800-762-5757 or 360-779-7901.
● Model No. of your projector : BOXLIGHT CP-13t
● Replacement Lamp Type No. : POA-LMP21J
(Service Parts No. 610 280 6939)
LAMP REPLACEMENT MONITOR TIMER
Be sure to reset the Lamp Replacement Monitor Timer when the Lamp Assembly is replaced. When the
Lamp Replacement Monitor Timer is reset, the LAMP REPLACEMENT indicator stops lighting.
Turn the projector on, and press the MENU button and the ON-SCREEN MENU will appear. Press the POINT
1
LEFT/RIGHT buttons to select SETTING
dialog box SETTING MENU will appear.
and press the SELECT button (refer to the page 40). Another
Press the POINT DOWN button and a red-arrow icon will appear. Move the arrow to Lamp age, and then press the
SELECT button. The message "Lamp replace monitor Reset?" is displayed.
2
3
Select [Yes] to reset the Timer.
Do not reset the Lamp Replacement Monitor Timer, except after the lamp is replaced.
43
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
TROUBLESHOOTING
Before calling your dealer or service station for assistance, check the matters below once again.
1. Make sure you have connected the projector to your equipment a s described in section "CONNECTING THE
PROJECTOR" on pages 10 ~ 13.
2. Check cable connection. Verify that all computer, video and power cord are properly connected.
3. Verify that all power is switched on.
4. If the projector still does not produce the image, re-start the computer.
5. If the image sill does not appear, unplug the projector from the computer and check the computer monitor's
display. The problem may be with your graphics controller rather than with the projector. (When you
reconnect the projector, remember to turn the computer and monitor off before your power up the projector.
Power the equipment back in order of : Projector and computer.)
6. If the problem still exists, check with following chart.
Problem:
No power.
Try these Solution
● Plug the projector into the AC outlet.
● Be sure READY Indicator light is On.
● Wait 90 seconds after the projector is turned OFF before turning the projector back on.
NOTE : After pressing the power ON-OFF switch to OFF, make sure the projector works
as follow.
1. The LAMP indicator will light and the READY indicator will turn off.
2. After 90 seconds, the READY indicator will light green again and the projector
may be turned on by pressing the power ON-OFF button.
● Check the TEMPERATURE WARNING indicator. If the indicator flashes red, the
projector cannot be turned on.
(See "TURNING ON/OFF THE PROJECTOR" section on page 20.)
● Check the Projection Lamp. (Refer to the page 43.)
● Adjust the focus
Image is out of
focus.
● Make sure the projection screen is at least 4.6’ (1.4m) from the projector.
● Check the projection lens to see if it needs cleaning.
NOTE : Moving the projector from a cool temperature location to a warm temperature
location may result in moisture condensation on the lens. In such an event, leave
the projector OFF an d wait until condensation disappears.
● Check Ceiling / Rear feature. (See “SETTING” section on page 40.)
● Check Ceiling feature. (See “SETTING” section on page 40.)
Picture is Left/Right
reversed.
Picture is
Top/Bottom
reversed.
● Check Display feature.(See “SETTING” section on page 40.)
Some displays are
not seen during the
Operation.
● Check the connection between the computer or video equipment and the projector.
● When turning the projector on, it is about 30 seconds to display the image.
● Check the system that you select is corresponding with the computer or the video
equipment.
No image.
● Make sure the temperature is not out of the Operating Temperature (5°C ~ 35°C).
● Check audio cable connection from audio input source.
● Adjust the audio source.
No sound.
● Press VOLUME (+) button.
● Press MUTE button.
44
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
Problem:
Remote Control Unit
does not work.
Try these Solution
● Check the batteries.
● Check the ALL-OFF switch on the Remote Control Unit is set to “ON.”.
● Make sure anything is blocking between the Remote Receiver and the Remote Control
Unit.
● Make sure you are not too far from the projector when using the Remote Control Unit.
Maximum operating range is 16.4’ (5m).
● Check the cable connection between the projector and the computer.
● Check the mouse setting on your computer.
● Turn the projector before your turn on the computer.
Wireless Mouse
function does not
work.
● Check the memory card is inserted properly into PC CARD SLOT.
● Check SmartMedia or PC Card Adapter is set properly.
● Check MCI mode is selected.
● Check the image data is recorded in the memory card properly.
● Start the projector again.
The image data in
memory card isn’t
displayed.
● Check the projector is turned on.
● Check “Card access” in VIEW menu is selected.
● Check Control Cable for Serial Port (optional) is connected properly.
● Check the memory card is inserted properly into PC CARD SLOT.
● Check Media Card Imager (supplied) is installed in your computer properly.
● Check the setting in Media Card Imager (like Serial Port Setting) is set properly.
The image data can’t
be written in, read
from the memory
card.
WARNING :
High voltages are used to operate this projector. Do not attempt to open the cabinet.
Boxlight Service is easily obtained. If after all operating instructions above, you find that service is necessary,
contact Boxlight for assistance at 1-800-762-5757 or 360-779-7901.
Give the model number and explain the difficulty. We will advise you how to obtain service.
45
Download from Www.Somanuals.com. All Manuals Search And Download.
TECHNICAL SPECIFICATIONS
Multi-media Projector
Projector Type
(not including Adjustable Feet)
9.41" x 3.54" x 12.72" (239mm x 90mm x 323mm)
8.82 lbs (4.0 kg)
(W x H x D)
Dimensions
Net Weight
0.9" TFT Active Matrix type, 3 panels
800 x 600 dots
LCD Panel System
Panel Resolution
Number of Pixels
Color System
1,440,000 (800 x 600 x 3 panels)
PAL, SECAM, NTSC, NTSC4.43, PAL-M and PAL-N
H-sync. 15 ~ 80 KHz, V-sync. 50 ~ 100 Hz
Adjustable from 30” to 300”
Scanning Frequency
Projection Image size
Horizontal Resolution
Projection Lens
Throw Distance
(Diagonal)
750 TV lines
F 1.7 ~ 2.0 lens with f 33.2mm ~ 43.1mm Motor zoom and focus
4.6’ ~ 35.4’ (1.4 m ~ 10.8 m)
150 W
Projection Lamp
AV Input Jacks
RCA Type x 1 (Video, Audio R and L) and Mini DIN 4 pin (S-Video) x 1
(VGA) HDB 15 Terminal x 1
Mini DIN 8 pin x 1
Computer Input Jacks
Control Port Jack
Monitor Output Jack
(VGA) HDB 15 Terminal x 1
Mini Jack (stereo)
Computer Audio Input Jack
Audio Output Jack
Internal Audio Amp
Built-in Speaker
Mini Jack (stereo)
1W RMS (Monaural)
1 speaker, 1.57" x 1.18" (40mm x 30mm)
0˚ to 10˚
Feet Adjustment
AC 100 ~ 120 V / 200 - 240 V, 50 / 60 Hz
2.5 A / 1.4 A (Max. Ampere)
41 ˚F ~ 95 ˚F (5 ˚C ~ 35 ˚C)
Voltage
Power Consumption
Operating Temperature
Storage Temperature
Remote Control Transmitter
14 ˚F ~ 140 ˚F (-10 ˚C ~ 60 ˚C)
Power Source
Operating Range
Dimensions
Net Weight
Laser Pointer
:
:
:
:
:
AA,UM3 or R06 Type x 2
16.4’ (5m) / ±30˚
2.2” x 1.3” x 7.6” (55mm x 34mm x 192mm)
0.35 lbs (160 g) (including batteries)
(Max. Output : 1mW / Wave length : 650±20nm)
Class II Laser
Owner’s Manual
AC Power Cord
Accessories
Remote Control Transmitter and Batteries
VGA Cable
Control Cable for PS/2 port
Media Card Imager for Windows 95 (CD-ROM)
and Owner's Manual for this software
SmartMedia and PC Card Adapter
Dust Cover
Lens Cover
● The specifications are subject to change without notice.
This symbol on the nameplate means the product is Listed by Underwriters Laboratories Inc. It
is designed and manufactured to meet rigid U.L. safety standards against risk of fire, casualty
and electrical hazards.
46
Download from Www.Somanuals.com. All Manuals Search And Download.
OPTIONAL PARTS
The parts listed below are optionally supplied. When ordering those parts, give the
name and the Type No. of it to the sales dealer.
● Control Cable for Serial Port
● Control Cable for ADB Port
● MAC Adapter
Type No. : POA-MCSRL
Type No. : POA-MCMAC
Type No. : POA-MACAP
47
Download from Www.Somanuals.com. All Manuals Search And Download.
LIMITED WARRANTY
BOXLIGHT CORPORATION (“BOXLIGHT”) warrants that each Boxlight CP-13t (“the Product”) sold hereunder will
conform to and function in accordance with the written specifications of BOXLIGHT. Said limited warranty shall apply
only to the first person or entity that purchases the Product for personal or business use and not for the purpose of
distribution resale. Said warranty shall continue for a period of two (2) years from the date of such purchase.
BOXLIGHT does not warrant that the Product will meet the specific requirements of the first person or entity that
purchases the Product for personal or business use. Lamp is warrantied for 120 days.
BOXLIGHT CORPORATION’s liability for the breach of the foregoing limited warranty is limited to the repair or
replacement of the Product or refund of the purchase price of the Product, at BOXLIGHT’s sole option. To exercise
the Purchaser’s rights under the foregoing warranty, the Product must be returned at the Purchaser’s sole cost and
expense, to BOXLIGHT or any authorized service center provided, however, that the Product must be accompanied by
a written letter explaining the problem and which includes (i) proof of purchase; (ii) the dealer’s name; (iii) the model
and serial number of the Product. A return authorization number, issued by the BOXLIGHT customer service
department, must also be clearly displayed on the outside of the shipping carton containing the Product.
WARRANTY LIMITATION AND EXCLUSION
BOXLIGHT CORPORATION shall have not further obligation under the foregoing limited warranty if the Product has
been damaged due to abuse, misuse, neglect, accident, unusual physical or electrical stress, unauthorized
modification, tampering, alterations, or service other than by BOXLIGHT or its authorized agents, causes other than
from ordinary use or failure to properly use the Product in the application for which said Product is intended.
DISCLAIMER OR UNSTATED WARRANTIES
The warranty printed above is the only warranty applicable to this purchase.
All other warranties express or implied, including, but not limited to, the implied warranties or merchantability and
fitness for a particular purpose are disclaimed. There are no warranties that extend beyond the face of hereof and the
foregoing warranty shall not be extended, altered or varied except by written instrument signed by BOXLIGHT
CORPORATION.
LIMITATION OR LIABILITY
It is understood and agreed that BOXLIGHT’s liability whether in contract, in tort, under any warranty, in negligence or
otherwise shall not exceed the return of the amount of the purchase price paid by purchaser and under no
circumstances shall BOXLIGHT be liable for special, indirect or consequential damages. The price stated for the
Product is a consideration in limiting BOXLIGHT’s liability. No action regardless of form, arising out of the agreement
to purchase the product, may be brought by purchaser more than one year after the cause of action has accrued.
BOXLIGHT
®
Boxlight
19332 Powder Hill Place
Poulsbo, WA 98370-7407 USA
U.S. and Canada 800-762-5757
International 360-779-7901
United Kingdom 0800-762-575
France 0800-9132-88
Germany 0800-180-8381
Printed in Japan
Part No. 610 280 7660 (1AA6P1P1961-- MA6L)
Download from Www.Somanuals.com. All Manuals Search And Download.
|