User Manual
XENYX 1204/1204FX
Thank you
Table of Contents
Congratulations! In purchasing the BEHRINGER XENYX you
have acquired a mixer whose small size belies its incredible
versatility and audio performance.
The XENYX Series represents a milestone in the
development of mixing console technology. With the
new XENYX microphone preamps including phantom
power as an option, balanced line inputs and a powerful
effects section, the mixing consoles in the XENYX Series
are optimally equipped for live and studio applications.
Owing to state-of-the-art circuitry your XENYX console
produces a warm analog sound that is unrivalled. With the
addition of the latest digital technology these best-in-class
consoles combine the advantages of both analog and digital 4. Installation............................................................. 11
technology.
This manual is available in English, German, French, Spanish, Italian, Russian,
Polish, Dutch, Finnish, Swedish, Danish, Portuguese, Greek, Japanese
and Chinese. There may also be more current versions of this document.
Download them by going to the appropriate product page at:
A50-00000-03763
Download from Www.Somanuals.com. All Manuals Search And Download.
XENYX 1204/1204FX User Manual
XENYX 1204/1204FX User Manual
2
3
Important Safety Instructions
1. Introduction
The microphone channels feature high-end XENYX Mic
Preamps that compare well with costly outboard preamps
in terms of sound quality and dynamics and boast the
following features:
!
CAUTION!
[6] Clean only with dry cloth.
◊
We should like to draw your attention to the fact that
extreme volumes may damage your hearing and/or
your headphones or loudspeakers. Turn the MAIN MIX
faders and phones control in the main section fully
[7] Do not block any ventilation openings. Install in accordance
with the manufacturer’s instructions.
[8] Do not install near any heat sources such as radiators, heat
registers, stoves, or other apparatus (including amplifiers) that
produce heat.
•
•
•
130 dB dynamic range for an incredible amount of
headroom
down before you switch on the unit. Always be careful
to set the appropriate volume.
A bandwidth ranging from below 10 Hz to over 200 kHz
for crystal-clear reproduction of even the finest nuances
[9] Do not defeat the safety purpose of the polarized or grounding-
type plug. A polarized plug has two blades with one wider
than the other. A grounding-type plug has two blades and
a third grounding prong. The wide blade or the third prong
are provided for your safety. If the provided plug does not fit
into your outlet, consult an electrician for replacement of the
obsolete outlet.
*
1.1 General mixing console functions
A mixing console fulfils three main functions:
Terminals marked with this symbol carry electrical current of
sufficient magnitude to constitute risk of electric shock. Use only
high-quality commercially-available speaker cables with ¼" TS
plugs pre-installed. All other installation or modification should be
performed only by qualified personnel.
The extremely low-noise and distortion-free circuitry
guarantees absolutely natural and transparent signal
reproduction
•
•
Signal processing: Preamplification, level adjustment,
mixing of effects, frequency equalization.
•
•
They are perfectly matched to every conceivable
microphone with up to 60 dB gain and +48 volt phantom
power supply
Signal distribution: Summing of signals to the
aux sends for effects processing and monitor mix,
distribution to one or several recording tracks, power
amp(s), control room and 2-track outputs.
[10] Protect the power cord from being walked on or pinched
particularly at plugs, convenience receptacles, and the point
where they exit from the apparatus.
They enable you to use the greatly extended dynamic
range of your 24-bit/192 kHz HD recorder to the full,
thereby maintaining optimal audio quality
*
This symbol, wherever it appears, alerts you to the presence of
uninsulated dangerous voltage inside the enclosure - voltage that
may be sufficient to constitute a risk of shock.
•
Mix: Setting the volume level, frequency distribution
and positioning of the individual signals in the stereo
field, level control of the total mix to match the recording
devices/crossover/power amplifier(s). All other mixer
functions can be included in this main function.
[11] Use only attachments/accessories specified by
the manufacturer.
“British EQ”
[12] Use only with the cart, stand, tripod, bracket,
or table specified by the manufacturer, or
sold with the apparatus. When a cart is used,
use caution when moving the cart/apparatus
combination to avoid injury from tip-over.
The equalizers used for the XENYX Series are based on
the legendary circuitry of top-notch consoles made in
Britain, which are renowned throughout the world for their
incredibly warm and musical sound character. Even with
extreme gain settings these equalizers ensure outstanding
audio properties.
!
The interface of BEHRINGER mixing consoles is optimized
for these tasks enabling you to easily keep track of the
signal path.
This symbol, wherever it appears, alerts you to important operating
and maintenance instructions in the accompanying literature.
Please read the manual.
[13] Unplug this apparatus during lightning
storms or when unused for long periods of time.
1.2 The user’s manual
Multi-effects processor
[14] Refer all servicing to qualified service personnel. Servicing is
required when the apparatus has been damaged in any way,
such as power supply cord or plug is damaged, liquid has been
spilled or objects have fallen into the apparatus, the apparatus
has been exposed to rain or moisture, does not operate
normally, or has been dropped.
The user’s manual is designed to give you both an overview
of the controls, as well as detailed information on how to use
them. In order to help you understand the links between
the controls, we have arranged them in groups according
to their function. If you need to know more about specific
where you’ll find explanations of e.g. effects and
Additionally, your XENYX mixing console has an effects
processor with 24-bit A/D and D/A converters included,
which gives you 100 presets producing first-class reverb,
delay and modulation effects plus numerous multi-effects in
excellent audio quality.
!
Caution
To reduce the risk of electric shock, do not remove the top cover
(or the rear section). No user serviceable parts inside. Refer servicing
to qualified personnel.
The XENYX mixing consoles are equipped with a state-
of-the-art switched-mode power supply (SMPS). Unlike
conventional circuitry an SMPS provides an optimum supply
current regardless of the input voltage. And thanks to its
considerably higher efficiency a switched-mode power
supply uses less energy than conventional power supplies.
[15] The apparatus shall be connected to a MAINS socket outlet
!
Caution
dynamics applications.
with a protective earthing connection.
To reduce the risk of fire or electric shock, do not expose this
appliance to rain and moisture. The apparatus shall not be exposed
to dripping or splashing liquids and no objects filled with liquids,
such as vases, shall be placed on the apparatus.
◊
The block diagram supplied with the mixing console
gives you an overview of the connections between the
inputs and outputs, as well as the associated switches
and controls.
[16] Where the MAINS plug or an appliance coupler is used as the
disconnect device, the disconnect device shall remain
readily operable.
USB/Audio interface
For the moment, just try and trace the signal path from the
microphone input to the aux send 1 connector. Don’t be
put off by the huge range of possibilities; it’s easier than you
think! If you look at the overview of the controls at the same
time, you’ll be able to quickly familiarize yourself with your
mixing console and you’ll soon be making the most of all its
many possibilities.
The USB interface supplied with the unit is a perfect
match for the XENYX Series and serves as a powerful
recording interface to your PC or MAC. It supports the
digital transmission of signals on up to four channels with
max. 48 kHz and extremely low latency. When wired to
the CD/TAPE INPUT and OUTPUT connectors, the interface
transfers the stereo mix from the console directly to a
computer. Both the recording signal and the playback signal
from the computer can be monitored at the same time.
In this way, you can use several recording runs to produce
complete multi-track recordings.
!
Caution
These service instructions are for use by qualified service personnel
only. To reduce the risk of electric shock do not perform any
servicing other than that contained in the operation instructions.
Repairs have to be performed by qualified service personnel.
[1] Read these instructions.
[2] Keep these instructions.
[3] Heed all warnings.
[4] Follow all instructions.
[5] Do not use this apparatus near water.
Download from Www.Somanuals.com. All Manuals Search And Download.
XENYX 1204/1204FX User Manual
XENYX 1204/1204FX User Manual
4
5
1.3 Before you get started
2.1.2 Equalizer
◊
If you press the MUTE/ALT 3-4 switch, aux send 1
is muted, provided that it is switched post-fader.
However, this does not affect the aux send 2 of
the 1204FX.
2. Control Elements and
All mono input channels include a 3-band equalizer. All
bands provide boost or cut of up to 15 dB. In the central
position, the equalizer is inactive.
1.3.1 Shipment
Connectors
Your mixing console was carefully packed in the factory to
guarantee safe transport. Nevertheless, we recommend
that you carefully examine the packaging and its contents
for any signs of physical damage, which may have occurred
during transit.
This chapter describes the various control elements of your
mixing console. All controls, switches and connectors will be
discussed in detail.
The circuitry of the British EQs is based on the technology
used in the best-known top-of-the-line consoles and
providing a warm sound without any unwanted side effects.
The result are extremely musical equalizers which, unlike
simple equalizers, cause no side effects such as phase
shifting or bandwidth limitation, even with extreme gain
settings of 15 dB.
AUX 1 (MON)
In the 1204FX, aux send 1 can be switched pre-fader and is
thus particularly suitable for setting up monitor mixes. In the
1204, the first aux send is labeled MON and is permanently
switched pre-fader.
2.1 Mono channels
◊
If the unit is damaged, please do NOT return it to us,
but notify your dealer and the shipping company
immediately, otherwise claims for damage or
replacement may not be granted.
2.1.1 Microphone and line inputs
PRE
When the PRE switch is pressed, aux send 1 is sourced
pre-fader.
1.3.2 Initial operation
AUX 2 (FX)
Be sure that there is enough space around the unit for
cooling purposes and to avoid over-heating please do not
place your mixing console on high-temperature devices
such as radiators or power amps. The console is connected
to the mains via the supplied cable. The console meets
the required safety standards. Blown fuses must only be
replaced by fuses of the same type and rating.
The aux send labeled FX is for sending to effects devices and
is thus set up to be post-fader.
In the 1204FX, the FX send is routed directly to the built-in
effects processor.
◊
If you wish to use the internal effects processor, the
STEREO AUX RETURN 2 connectors should not be
in use.
Fig. 2.2: The equalizer of the input channels
◊
Please note that all units must be properly grounded.
For your own safety, you should never remove any
ground connectors from electrical devices or power
cables, or render them inoperative.
The upper (HI) and the lower band (LO) are shelving filters
that increase or decrease all frequencies above or below
their cut-off frequency. The cut-off frequencies of the upper
and lower band are 12 kHz and 80 Hz respectively. The mid
band is configured as a peak filter with a center frequency
of 2.5 kHz.
Fig. 2.1: Connectors and controls of mic/line inputs
◊
1204FX: you can also connect an external effects
processor to aux send 2, however the internal effects
module will be muted.
MIC
◊
Please ensure that only qualified people install and
operate the mixing console. During installation and
operation, the user must have sufficient electrical
contact to earth, otherwise electrostatic discharges
might affect the operation of the unit.
Each mono input channel offers a balanced microphone input
via the XLR connector and also features switchable +48V
phantom power supply for condenser microphones.The
XENYX preamps provide undistorted and noise-free gain as is
typically known only from costly outboard preamps.
2.1.4 Routing switch, solo and channel fader
2.1.3 Aux sends
1.3.3 Online registration
◊
Please mute your playback system before you activate
the phantom power supply to prevent switch-on
thumps being directed to your loudspeakers. Please
also note the instructions in chapter 2.4.2“Voltage
supply, phantom power and fuse”.
Please do remember to register your new
BEHRINGER equipment right after your purchase
conditions of our warranty carefully.
Fig. 2.3: The AUX SEND controls in the channel strips
LINE IN
Should your BEHRINGER product malfunction, our goal
is to have it repaired as quickly as possible. To arrange for
warranty service, please contact the retailer from whom the
equipment was purchased. Should your BEHRINGER dealer
not be located in your vicinity, you may directly contact
one of our subsidiaries. Corresponding contact information
is included in the original equipment packaging (Global
Contact Information/European Contact Information). Should
your country not be listed, please contact the distributor
nearest you. A list of distributors can be found in the support
area of our website (www.behringer.com).
Aux sends take signals via a control from one or more
channels and sum these signals to a so-called bus. This bus
signal is sent to an aux send connector and then routed,
for example, to an active monitor speaker or an external
effects device. The return from an external effect can then be
brought back into the console via the aux return connectors.
Each mono input also features a balanced line input on a
¼" connector. Unbalanced devices (mono jacks) can also be
connected to these inputs.
◊
Please remember that you can only use either the
microphone or the line input of a channel at any one
time. You can never use both simultaneously!
For situations which require effects processing, the aux
sends are usually switched post-fader so that the effects
volume in a channel corresponds to the position of the
channel fader. If this were not the case, the effects signal
of the channel would remain audible even when the fader
is turned to zero. When setting up a monitor mix, the aux
sends are generally switched to pre-fader; i.e. they operate
independently of the position of the channel fader.
LOW CUT
Fig. 2.4: Panorama and routing controls
The mono channels of the mixing consoles have a
high-slope LOW CUT filter for eliminating unwanted,
low-frequency signal components (75 Hz, 18 dB/octave).
PAN
Registering your purchase and equipment with us helps us
process your repair claims quicker and more efficiently.
The PAN control determines the position of the channel
signal within the stereo image. This control features a
constant-power characteristic, which means the signal
is always maintained at a constant level, irrespective of
position in the stereo panorama.
GAIN
Thank you for your cooperation!
Use the GAIN control to adjust the input gain. This control
should always be turned fully counterclockwise whenever
you connect or disconnect a signal source to one of
the inputs.
Both aux sends are mono, are sourced after the equalizer
and offer up to +15 dB gain.
Download from Www.Somanuals.com. All Manuals Search And Download.
XENYX 1204/1204FX User Manual
XENYX 1204/1204FX User Manual
6
7
MUTE/ALT 3-4
of a stereo signal is needed. There is often a discrepancy
between the settings of the left and the right channels when
using separate equalizers.
◊
If you want to monitor the signal of just one AUX bus,
none of the other SOLO SWITCHES should be pressed
and the MODE switch must be in the SOLO position
(not pressed down).
◊
◊
In this instance, the FX control of the channel being
used as an effects return should be turned fully
counterclockwise, otherwise feedback problems
could occur!
You can use the MUTE/ALT 3-4 switch to divert the channel
from the main mix bus to the Alt 3-4 bus. This mutes the
channel from the main mix.
2.2.3 Aux sends stereo channels
If you wish to use the internal effects processor, no
connectors should be plugged into STEREO AUX
RETURN 2.
MUTE-LED
2.3.2 Aux send connectors 1 and 2
In principle, the aux sends of the stereo channels function
in just the same way as those of the mono channels. As aux
send paths are always mono, the signal on a stereo channel
is first summed to mono before it reaches the aux bus.
The MUTE LED indicates that the relevant channel is diverted
to the submix (Alt 3-4 bus).
2.3.4 Stereo aux return
CLIP-LED
The CLIP LED lights up when the input signal is driven
too high. In this case, turn down the GAIN control and, if
necessary, check the setting of the channel EQ.
2.2.4 Routing switch, solo and channel fader
BAL
Fig. 2.7: Aux send connectors
The function of the BAL(ANCE) control corresponds to the
PAN control in the mono channels.
SOLO
AUX SEND 1
The SOLO switch (1204FX only) is used to route the channel
signal to the solo bus (Solo In Place) or to the PFL bus (Pre
Fader Listen). This enables you to monitor a channel signal
without affecting the main output signal. The signal you hear
is sourced either before (PFL, mono) or after (solo, stereo)
both the pan control and the channel fader (see chapter
2.3.6“Level meters and monitoring”).
The balance control determines the relative proportion
between the left and right input signals before both signals
are routed to the main stereo mix bus.
If you use aux send 1 pre-fader, you would usually connect
the AUX SEND 1 connector to monitors via a power amp (or
an active monitor system). If you use aux send 1 post-fader,
proceed as described under aux send 2.
Fig. 2.9: Stereo aux return controls
The MUTE/ALT 3-4 switch, the MUTE-LED, the CLIP-LED, the
SOLO switch and the channel fader function in the same way
as the mono channels.
STEREO AUX RETURN 1
STEREO AUX RETURN 1 is a stereo control which determines
the level of the signal in the main mix. If STEREO AUX
RETURN 1 is used as effects return, you can add the effects
signal to any“dry”channel signal.
AUX SEND 2
The AUX SEND 2 connector outputs the signal you picked
up from the individual channels using the FX control. You
can connect this to the input of an effects device in order to
process the FX bus signal. Once an effects mix is created, the
processed signal can then be routed from the effects device
output back into the STEREO AUX RETURN connectors.
The channel fader determines the level of the channel signal
in the main mix (or submix).
2.3 Connector panel and main section
Whereas it was useful to trace the signal flow from top to
bottom in order to gain an understanding of the channel
strips, we now look at the mixing console from left to right.
The signals are, so to speak, collected from the same point
on each of the channel strips and then routed to the main
section all together.
◊
In this instance, the effects device should be set at
100% effect.
2.2 Stereo channels
STEREO AUX RETURN MON
2.2.1 Channel inputs
The STEREO AUX RETURN MON control has a special function:
it can be used to add an effect to a monitor mix.
For example:
2.3.3 Stereo aux return connectors
2.3.1 Aux sends 1 and 2
Monitor mix with effect
In this instance, the effects device should be set up as
follows: AUX SEND 2 is connected to the L/Mono input
of your effects device, while its outputs are connected
to STEREO AUX RETURN 1. Connect the amplifier of your
monitor system to AUX SEND 1. The AUX SEND 1 master
control determines the volume of the monitor mix.
Fig. 2.5: Stereo channel inputs and LEVEL switch
Fig. 2.8: Stereo aux return connectors
Each stereo channel has two balanced line level inputs on
¼" connectors for left and right channels. If only the
connector marked“L”is used, the channel operates in
mono. Stereo channels are designed to handle typical line
level signals.
Fig. 2.6: AUX SEND controls of the main section
STEREO AUX RETURN 1
You can now use the STEREO AUX RETURN MON control
to adjust the level of the effects signal routed to the
monitor mix.
A channel signal is routed to aux send bus 1 if the AUX 1
control is turned up on the corresponding channel.
The STEREO AUX RETURN 1 connectors generally serve as the
return path for the effects mix generated using the post-
fader aux send. This is where you connect the output signal
of the external effects device. If only the left connector is
used, the AUX RETURN automatically operates in mono.
You can easily use the headphones distribution amplifier
BEHRINGER POWERPLAY PRO HA4600/HA4700/HA8000
to provide you with four (or eight with the HA8000) stereo
headphone mixes for your studio.
Both inputs can also be used with unbalanced jacks.
AUX SEND 1 (MON)
LEVEL
The AUX SEND control MON acts as master control for aux
send 1 and determines the level of the summed signal. In the
1204FX, the MON control is called AUX SEND 1.
For level matching, the stereo inputs feature a LEVEL switch
which selects between +4 dBu and -10 dBV. At -10 dBV
(home-recording level), the input is more sensitive than at
+4 dBu (studio level).
◊
You can also use these connectors as additional
line inputs.
STEREO AUX RETURN 2 (FX)
AUX SEND 2 (FX)
STEREO AUX RETURN 2
The STEREO AUX RETURN 2 control determines the level of
signals fed into the AUX RETURN 2 connectors which are
routed to the main mix.
Similarly, the FX control (AUX SEND 2) determines the level
for aux send 2.
The STEREO AUX RETURN 2 connectors serve as the return
path for the effects mix generated using the FX control.
If these connectors already function as additional inputs,
you can route the effects signal back into the console via a
different channel, with the added benefit that the channel
EQ can be used to adjust the frequency response of the
effects return signal.
2.2.2 Equalizer stereo channels
The equalizer of the stereo channels is, of course, stereo. The
filter characteristics and crossover frequencies are the same
as those of the mono channels. A stereo equalizer is always
preferable to two mono equalizers if frequency correction
SOLO
MAIN MIX/ALT 3-4
You can use the SOLO switch (1204FX only) to separately
monitor the aux sends via the CONTROL ROOM/PHONES
outputs and check these with the level meters.
The MAIN MIX/ALT 3-4 switch routes the signal connected to
STEREO AUX RETURN 2 to either main mix (not pressed) or
submix (Alt 3-4, pressed).
Download from Www.Somanuals.com. All Manuals Search And Download.
XENYX 1204/1204FX User Manual
XENYX 1204/1204FX User Manual
8
9
2.3.5 Tape input / tape output
MAIN MIX
MODE (1204FX only)
PHONES
The MAIN MIX switch sends the main mix signal to the
above-mentioned outputs and to the level meter.
The MODE switch determines whether the channels’SOLO
switch operates as PFL (Pre Fader Listen) or as solo (Solo
In Place).
You can connect headphones to this ¼" TRS connector. The
signal on the PHONES connection is sourced from the control
room output.
PHONES/CTRL R(oom)
PFL
Use this control to set control room output level and head-
phones volume respectively.
2.3.7 Alt 3-4 and main mix fader
To activate the PFL function, depress the MODE switch.
The PFL function should, as a rule, be used for gain setting
purposes. The signal is sourced pre-fader and assigned to the
mono PFL bus. In the“PFL”setting, only the left side of the
peak meter operates. Drive the individual channels to the
0 dB mark of the VU meter.
CD/TAPE TO MAIN
Fig. 2.10: 2-track connectors
When the CD/TAPE TO MAIN switch is depressed, the 2-track
input is routed to the main mix and thus serves as an
additional input for tape machines. You can also connect
MIDI instruments or other signal sources here that do not
require any further processing. At the same time, this switch
disables the main mix to tape output link.
CD/TAPE INPUT
The CD/TAPE INPUT RCA connectors are provided for
connecting a 2 track machine (e.g. DAT recorder). They can
also be used as stereo line input. Alternatively, the output
signal of a second XENYX or BEHRINGER ULTRALINK PRO
Solo
When the MODE switch is not depressed, the stereo solo bus
is active. Solo is short for“Solo In Place”. This is the customary
method for listening to an individual signal or to a group of
signals. As soon as a solo switch is pressed, all channels in the
control room (and headphones) that have not been selected
are muted thereby retaining stereo panning. The solo bus
can carry the output signals of the channel pan controls, the
aux sends and the stereo line inputs. The solo bus is, as a rule,
switched post-fader.
MX882 can also be connected. If you connect a hi-fi amplifier POWER
with a source selection switch to the CD/TAPE INPUT, you
can easily switch between additional sources (e.g. cassette
recorder, CD player, etc.).
The blue POWER LED indicates that the device is switched on.
+48 V
The red“+48 V”LED lights up when the phantom power
supply is switched on. The phantom power supply is
necessary for condenser microphones and is activated using
the switch on the rear of the device.
CD/TAPE OUTPUT
These connectors are wired in parallel with the MAIN OUT
and carry the main mix signal (unbalanced). Connect the
CD/TAPE OUTPUT to the inputs of your recording device.
The final output level can be adjusted via the high-precision
MAIN MIX fader.
Fig. 2.13: Alt 3-4 and main mix fader
◊
The PAN control in the channel strip offers a constant
power characteristic. This means that the signal is
always at a constant level, irrespective of its position in
the stereo panorama. If the PAN control is moved fully
left or right from center, the level increases by 4 dB in
that channel. This ensures that, when set in the center,
the audio signal is not louder. For this reason, with the
solo function activated (Solo in Place), audio signals
from the channels with PAN controls that have not
been moved fully to the left or right are displayed at a
lower volume than in the PFL function.
◊
Please do not connect microphones to the mixer (or
the stagebox/wallbox) while the phantom power
supply is switched on. Connect micro-phones before
you switch on the power supply. In addition, the
monitor/PA loudspeakers should be muted before you
activate the phantom power supply. After switching
on, wait approx. one minute to allow for system
stabilization.
Use the high-precision quality faders to control the output
level of the Alt 3-4 subgroup and main mix.
◊
If you connect a compressor or a noise gate after the
2-track output, the faders will probably not be able to
create a satisfactory fade-out effect.
2.4 Rear view of 1204FX/1204
2.4.1 Main mix outputs, Alt 3-4 outputs and
control room outputs
2.3.6 Level meter and monitoring
LEVEL METER
The high-precision level meter accurately displays the
appropriate signal level.
As a rule, solo signals are monitored via the control room
outputs and headphones connector and are displayed by
the level meters. If a solo switch is pressed, the signals from
the tape input, Alt 3-4 and main mix are blocked from the
control room outputs, the headphone connector and the
level meter.
LEVEL SETTING:
Fig. 2.14: Main mix outputs, Alt 3-4 outputs and control room outputs
When recording to a digital device, the recorder’s peak
meter should not exceed 0 dB. This is because, unlike analog
recordings, slightly excessive levels can create unpleasant
digital distortion.
MAIN OUTPUTS
MAIN SOLO (1204FX only)
The MAIN outputs carry the MAIN MIX signal and are on
balanced XLR connectors with a nominal level of +4 dBu.
Fig. 2.11: Control room/phones section, level meter
When recording to an analog device, the VU meters of the
recording machine should reach approx. +3 dB with low-
frequency signals (e.g. kick drum). Due to their inertia VU
meters tend to display too low a signal level at frequencies
above 1 kHz. This is why, for example, a Hi-Hat should only
be driven as far as -10 dB. Snare drums should be driven to
approx. 0 dB.
The MAIN SOLO LED lights up as soon as a channel or aux
send solo switch is pressed. The MODE switch also has to be
set at“Solo”.
ALT 3-4 OUTPUTS
CD/TAPE
The ALT 3-4 outputs are unbalanced and carry the signals
of the channels that you have assigned to this group using
the MUTE switch. This can be used to route a subgroup to a
further mixing console for example, or or it could be used as
a recording output working in tandem with the main output.
This means you could record to four tracks simultaneously.
The icing on the cake, so to speak, is that you could connect
Y-cables to these four outputs and then connect your
8-track recorder in such a way that you have 2 x 4 tracks (e.g.
channel 1 feeds track 1 and track 2, etc.). In the first recording
pass, you record on tracks 1, 3, 5 and 7 and in the second
pass, on tracks 2, 4, 6 and 8.
The TAPE switch routes the signal from the TAPE IN
PFL (1204FX only)
connectors to the level meter, the CONTROL ROOM OUT
outputs and the PHONES connector this is a simple way to
check recorded signals via monitor speakers or headphones.
The PFL LED indicates that the peak meter is set to PFL mode.
◊
The peak meters of your XENYX display the level
virtually independent of frequency. A recording level
of 0 dB is recommended for all signal types.
ALT 3-4
Similarly, the ALT 3-4 switch routes the signal from the
Alt 3-4 bus to the same path for monitoring purposes.
Fig. 2.12: PHONES connector
Download from Www.Somanuals.com. All Manuals Search And Download.
XENYX 1204/1204FX User Manual
XENYX 1204/1204FX User Manual
10
11
CONTROL ROOM OUTPUTS
◊
Caution!You must never use unbalanced XLR
connectors (pin 1 and 3 connected) on the MIC inputs
if you intend to use the phantom power supply.
3. Digital Effects Processor
4. Installation
4.1 Rack mounting
The packaging of your mixing console contains two 19" rack
mount wings which can be installed on the side panels of
the console.
The control room output is normally connected to the
monitor system in the control room and provides the stereo
mix or, when required, the solo signal.
input
2.4.2 Voltage supply, phantom power and fuse
2
1
3
Before you can attach the rack mount wings to the mixing
console, you need to remove the screws holding the left and
right side panels. Use these screws to fasten the two wings
onto the console, being careful to note that each wing fits a
specific side. With the rack mount wings installed, you can
mount the mixing console in a commercially available 19"
rack. Be sure to allow for proper air flow around the unit, and
do not place the mixing console close to radiators or power
amps, so as to avoid overheating.
1 = ground/shield
2 = hot (+ve)
3 = cold (-ve)
output
Fig. 2.15: Voltage supply and fuse
Fig. 3.1: Digital effects module (only 1204FX)
1
2
◊
Only use the screws holding the mixing console side
panels to fasten the 19" rack mounts.
FUSE HOLDER
24-BIT MULTI-EFFECTS PROCESSOR
3
The console is connected to the mains via the cable supplied
which meets the required safety standards. Blown fuses
must only be replaced by fuses of the same type and rating.
Here you can find a list of all presets stored in the multi-
effects processor. This built-in effects module produces
high-grade standard effects such as reverb, chorus, flanger,
delay and various combination effects. The integrated effects
module has the advantage of requiring no wiring. This
way, the danger of creating ground loops or uneven signal
levels is eliminated at the outset, completely simplifying
the handling.
4.2 Cable connections
For unbalanced use, pin 1 and pin 3 have to be bridged
You will need a large number of cables for the various
connections to and from the console. The illustrations below
show the wiring of these cables. Be sure to use only
high-grade cables.
IEC MAINS RECEPTACLE
Balanced use with XLR connectors
The mains connection is via a cable with IEC mains
connector. An appropriate mains cable is supplied with
the equipment.
Fig. 4.2: XLR connections
strain relief clamp
sleeve
Strain relief clamp
Sleeve
These effect presets are designed to be added to dry signals.
If you move the FX TO MAIN control, you mix the channel
signal (dry) and the effect signal.
POWER
Use the POWER switch to power up the mixing console.
tip
Tip
PHANTOM
This also goes for mixing effects signals with the monitor
mix. The main difference is that the mix ratio is adjusted
using the FX TO MON control. Of course, a signal has to
be fed into the effects processor via the FX control in the
channel strip for both applications.
The PHANTOM switch activates the phantom power supply
for the XLR connectors of the mono channels which is
required to operate condenser microphones. The red
+48 V LED lights up when phantom power is on. As a rule,
dynamic microphones can still be used with phantom power
switched on, provided that they are wired in a balanced
configuration. In case of doubt, contact the microphone
manufacturer!
sleeve
pole 1/ground
Sleeve
(ground/shield)
◊
On the following page, you will find an illustration
showing how to connect your foot switch correctly.
LEVEL
tip
pole 2
The LED level meter on the effects module should display
a sufficiently high level. Take care to ensure that the clip
LED only lights up at peak levels. If it is lit constantly, you
are overloading the effects processor and this could
cause unpleasant distortion. The FX control (AUX SEND 2)
determines the level that reaches the effects module.
Tip
(signal)
◊
After the phantom power supply has been switched
on, do not connect microphones to the mixer (or
the stagebox/wallbox). Connect the microphones
before you switch phantom power on. In addition, the
monitor/PA loudspeakers should be muted before
activating the phantom power supply. After switching
on, wait approx. one minute to allow the system
to stabilize.
The footswitch connects both poles momentarily
Unbalanced ¼" TS connector
1/4" TS footswitch connector
Fig. 4.3: ¼" TS connector
Fig. 4.1: ¼" TS connector for foot switch
PROGRAM
You can select the effect preset by turning the PROGRAM
control. The display flashes the number of the current preset.
To recall the selected preset, press the button; the flashing
stops. You can also recall the selected preset with the
foot switch.
4.2.1 Audio connections
Please use commercial RCA cables to wire the 2-track inputs
and outputs.
◊
Caution!You must never use unbalanced XLR
connectors (PIN 1 and 3 connected) on the MIC
input connectors if you want to use the phantom
power supply.
You can, of course, also connect unbalanced devices to the
balanced input/outputs. Use either mono plugs, or ensure
that ring and sleeve are bridged inside the stereo plug (or
pins 1 & 3 in the case of XLR connectors).
SERIAL NUMBER
Please note the important information on the serial number
given in chapter 1.3.3.
Download from Www.Somanuals.com. All Manuals Search And Download.
XENYX 1204/1204FX User Manual
XENYX 1204/1204FX User Manual
12
13
strain relief clamp
5. Specifications
Mono inputs
sleeve
ring
tip
Aux sends
Type
physical
¼"TS connector, unbalanced
approx. 120 Ω
Microphone inputs (XENYX Mic Preamp)
1204FX
Impedance
Max. output level
Type
XLR, electronically balanced,
discrete input circuit
Dimensions (H x W x D)
approx. 97 mm (3 7/8") x 247 mm
(9 11/16") x 334 mm (13 5/32")
+22 dBu
Weight (net)
approx. 2.60 kg (5 3/4 lbs)
Mic E.I.N. (20 Hz - 20 kHz)
@ 0 Ω source resistance
@ 50 Ω source resistance
@ 150 Ω source resistance
Frequency response
Stereo aux returns
sleeve
ground/shield
-134 dB / 135.7 dB A-weighted
-131 dB / 133.3 dB A-weighted
-129 dB / 130.5 dB A-weighted
1204
Type
¼"TRS connector,
electronically balanced
Dimensions (H x W x D)
approx. 97 mm (3 7/8") x 247 mm
(9 11/16") x 328 mm (13")
Impedance
approx. 20 kΩ bal. / 10 kΩ unbal.
+22 dBu
ring
cold (-ve)
Weight (net)
approx. 2.56 kg (5 5/8lbs)
Max. input level
<10 Hz - 150 kHz (-1 dB),
<10 Hz - 200 kHz (-3 dB)
tip
hot (+ve)
Main outputs
Type
Measuring conditions:
Gain range
+10 to +60 dB
XLR, electronically balanced
approx. 240 Ω bal. / 120 Ω unbal.
+28 dBu
For connection of balanced and unbalanced plugs,
ring and sleeve have to be bridged at the stereo plug.
Max. input level
Impedance
+12 dBu @ +10 dB gain
approx. 2.6 kΩ balanced
1: 1 kHz rel. to 0 dBu; 20 Hz - 20 kHz; line input; main output; unity gain.
Impedance
Max. output level
2: 20 Hz - 20kHz; measured at main output. Channels 1 - 4 unity gain; EQ flat; all channels on main mix;
channels 1/3 as far left as possible, channels 2/4 as far right as possible. Reference = +6 dBu.
Balanced 1/4" TRS connector
Signal-to-noise ratio
110 dB / 112 dB A-weighted
(0 dBu In @ +22 dB gain)
Control room outputs
Type
Fig. 4.4: ¼"TRS connector
¼"TS connector, unbal.
approx. 120 Ω
Distortion (THD+N)
0.005 % / 0.004 % A-weighted
BEHRINGER is constantly striving to manintain the highest professional standards. As a result of these efforts,
modifications may be made from time to time to existing products without prior notice. Specifications and
appearance may differ from those listed or illustrated.
strain relief clamp
Impedance
Line input
sleeve
ring
tip
Max. output level
+22 dBu
Type
¼" TRS connector
electronically balanced
Headphones output
Type
Impedance
approx. 20 kΩ balanced
10 kΩ unbalanced
-10 to +40 dB
¼"TRS connector, unbalanced
+19 dBu / 150 Ω (+25 dBm)
24-bit Texas Instruments
Max. output level
DSP
Gain range
Max. input level
30 dBu
Converter
24-bit Sigma-Delta,
sleeve
ground/shield
64/128-times oversampling
Fade-out attenuation1
(Crosstalk attenuation)
Main fader closed
Sampling rate
40 kHz
Main Mix systeM data2
90 dB
89.5 dB
89 dB
ring
right signal
Channel muted
Noise
tip
left signal
Channel fader closed
Main mix @ -oo, Channel fader -oo
Main mix @ 0 dB, Channel fader -oo
Main Mix @ 0 dB, Channel fader @ 0 dB
-105 dB / -108 dB A-weighted
-95 dB / -97 dB A-weighted
-82,5 dB / -85 dB A-weighted
Frequency response
Microphone input to main out
<10 Hz - 90 kHz
1/4" TRS headphones connector
Power supply
Mains voltage
Power consumption
Fuse
+0 dB / -1 dB
+0 dB / -3 dB
Fig. 4.5: ¼"TRS connector for headphones
100 - 240 V~, 50/60 Hz
40 W
<10 Hz - 160 kHz
Stereo inputs
100 - 240 V~: T 1.6 A H 250 V
Standard IEC receptacle
Type
¼"TRS connector,
electronically balanced
Mains connection
Impedance
approx. 20 kΩ
+22 dBu
Max. input level
EQ mono channels
Low
Mid
High
80 Hz / 15 dB
2.5 kHz / 15 dB
12 kHz / 15 dB
EQ stereo channels
Low
Mid
High
80 Hz / 15 dB
2.5 kHz / 15 dB
12 kHz / 15 dB
Download from Www.Somanuals.com. All Manuals Search And Download.
XENYX 1204/1204FX User Manual
XENYX 1204/1204FX User Manual
14
15
Limited Warranty
§ 1 Warranty
Legal Disclaimer
§ 6 Claim for damage
Technical specifications and appearance are subject to change without
[2] This limited warranty does not cover the product if it has been electronically or
mechanically modified in any way. If the product needs to be modified or adapted in
order to comply with applicable technical or safety standards on a national or local
level, in any country which is not the country for which the product was originally
developed and manufactured, this modification/adaptation shall not be considered
a defect in materials or workmanship. This limited warranty does not cover any such
modification/adaptation, regardless of whether it was carried out properly or not.
Under the terms of this limited warranty, BEHRINGER shall not be held responsible for
any cost resulting from such a modification/adaptation.
notice. The information contained herein is correct at the time of printing.
BEHRINGER accepts no liability for any loss which may be suffered by any
person who relies either wholly or in part upon any description, photograph
or statement contained herein. Colors and specifications may vary slightly
from product. BEHRINGER products are sold through authorized dealers
only. Distributors and dealers are not agents of BEHRINGER and have
absolutely no authority to bind BEHRINGER by any express or implied
undertaking or representation. This manual is copyrighted. No part of
this manual may be reproduced or transmitted in any form or by any
means, electronic or mechanical, including photocopying and recording
of any kind, for any purpose, without the express written permission of
Red Chip Company Ltd.
Subject only to the operation of mandatory applicable local laws, BEHRINGER shall
have no liability to the buyer under this warranty for any consequential or indirect loss
or damage of any kind. In no event shall the liability of BEHRINGER under this limited
warranty exceed the invoiced value of the product.
[1] This limited warranty is valid only if you purchased the product from a BEHRINGER
authorized dealer in the country of purchase. A list of authorized dealers can be found
the BEHRINGER office closest to you.
[2] BEHRINGER* warrants the mechanical and electronic components of this product
to be free of defects in material and workmanship if used under normal operating
conditions for a period of one (1) year from the original date of purchase (see the
LimitedWarranty terms in § 4 below), unless a longer minimum warranty period
is mandated by applicable local laws. If the product shows any defects within the
specified warranty period and that defect is not excluded under § 4, BEHRINGER
shall, at its discretion, either replace or repair the product using suitable new or
reconditioned product or parts. In case BEHRINGER decides to replace the entire
product, this limited warranty shall apply to the replacement product for the remaining
initial warranty period, i.e., one (1) year (or otherwise applicable minimum warranty
period) from the date of purchase of the original product.
§ 7 Limitation of liability
This limited warranty is the complete and exclusive warranty between you and
BEHRINGER. It supersedes all other written or oral communications related to this
product. BEHRINGER provides no other warranties for this product.
[3] This limited warranty covers only the product hardware. It does not cover
technical assistance for hardware or software usage and it does not cover any software
products whether or not contained in the product. Any such software is provided“AS IS”
unless expressly provided for in any enclosed software limited warranty.
§ 8 Other warranty rights and national law
[1] This limited warranty does not exclude or limit the buyer’s statutory rights as a
consumer in any way.
ALL RIGHTS RESERVED.
[4] This limited warranty is invalid if the factory-applied serial number has been
altered or removed from the product.
[2] The limited warranty regulations mentioned herein are applicable unless they
constitute an infringement of applicable mandatory local laws.
© 2009 Red Chip Company Ltd.
Trident Chambers, Wickhams Cay, P.O. Box 146,
Road Town, Tortola, British Virgin Islands
[5] Free inspections and maintenance/repair work are expressly excluded from this
limited warranty, in particular, if caused by improper handling of the product by the
user. This also applies to defects caused by normal wear and tear, in particular, of faders,
crossfaders, potentiometers, keys/buttons, guitar strings, illuminants and similar parts.
[3] This warranty does not detract from the seller’s obligations in regard to any lack of
conformity of the product and any hidden defect.
[3] Upon validation of the warranty claim, the repaired or replacement product will
be returned to the user freight prepaid by BEHRINGER.
[4] Warranty claims other than those indicated above are expressly excluded.
§ 9 Amendment
[6] Damage/defects caused by the following conditions are not covered by this
limited warranty:
PLEASE RETAIN YOUR SALES RECEIPT. IT IS YOUR PROOF OF PURCHASE COVERING
YOUR LIMITED WARRANTY. THIS LIMITED WARRANTY IS VOID WITHOUT SUCH
PROOF OF PURCHASE.
Warranty service conditions are subject to change without notice. For the latest
warranty terms and conditions and additional information regarding BEHRINGER’s
•
improper handling, neglect or failure to operate the unit in compliance with
the instructions given in BEHRINGER user or service manuals;
connection or operation of the unit in any way that does not comply with the
technical or safety regulations applicable in the country where the product
is used;
§ 2 Online registration
•
* BEHRINGER Macao Commercial Offshore Limited of Rue de Pequim No. 202-A, Macau Finance Centre 9/J,
Macau, including all BEHRINGER group companies
Please do remember to register your new BEHRINGER equipment right after your
conditions of our limited warranty carefully. Registering your purchase and equipment
with us helps us process your repair claims quicker and more efficiently. Thank you for
your cooperation!
•
damage/defects caused by acts of God/Nature (accident, fire, flood, etc) or any
other condition that is beyond the control of BEHRINGER.
[7] Any repair or opening of the unit carried out by unauthorized personnel
(user included) will void the limited warranty.
§ 3 Return authorization number
[8] If an inspection of the product by BEHRINGER shows that the defect in question is
[1] To obtain warranty service, please contact the retailer from whom the equipment
was purchased. Should your BEHRINGER dealer not be located in your vicinity, you
may contact the BEHRINGER distributor for your country listed under“Support”at
be dealt with by our“Online Support”which may also be found under“Support”
by a description of the problem and the serial number of the product. After verifying
the product’s warranty eligibility with the original sales receipt, BEHRINGER will then
issue a Return Materials Authorization (“RMA”) number.
not covered by the limited warranty, the inspection costs are payable by the customer.
[9] Products which do not meet the terms of this limited warranty will be repaired
exclusively at the buyer’s expense. BEHRINGER or its authorized service center will
inform the buyer of any such circumstance. If the buyer fails to submit a written repair
order within 6 weeks after notification, BEHRINGER will return the unit C.O.D. with a
separate invoice for freight and packing. Such costs will also be invoiced separately
when the buyer has sent in a written repair order.
[10] Authorized BEHRINGER dealers do not sell new products directly in online
auctions. Purchases made through an online auction are on a“buyer beware”
basis. Online auction confirmations or sales receipts are not accepted for warranty
verification and BEHRINGER will not repair or replace any product purchased through
an online auction.
[2] Subsequently, the product must be returned in its original shipping carton,
together with the return authorization number to the address indicated by BEHRINGER.
[3] Shipments without freight prepaid will not be accepted.
§ 5 Warranty transferability
§ 4 Warranty Exclusions
This limited warranty is extended exclusively to the original buyer (customer of
authorized retail dealer) and is not transferable to anyone who may subsequently
purchase this product. No other person (retail dealer, etc.) shall be entitled to give any
warranty promise on behalf of BEHRINGER.
[1] This limited warranty does not cover consumable parts including, but not limited
to, fuses and batteries. Where applicable, BEHRINGER warrants the valves or meters
contained in the product to be free from defects in material and workmanship for a
period of ninety (90) days from date of purchase.
Download from Www.Somanuals.com. All Manuals Search And Download.
XENYX 1204/1204FX User Manual
XENYX 1204/1204FX User Manual
16
17
FEDERAL COMMUNICATIONS
COMMISSION COMPLIANCE
INFORMATION
XENYX 1204/1204FX
Responsible party name: BEHRINGER USA, Inc.
Address:
18912 North Creek Parkway,
Suite 200 Bothell, WA 98011,
USA
Phone/Fax No.:
Phone: +1 425 672 0816
Fax: +1 425 673 7647
hereby declares that the product
XENYX 1204/1204FX
complies with the FCC rules as mentioned in the following
paragraph:
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to part
15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause
harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more
of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
receiver.
• Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician
for help.
This device complies with Part 15 of the FCC rules. Operation
is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received,
including interference that may cause undesired operation.
Download from Www.Somanuals.com. All Manuals Search And Download.
XENYX 1204/1204FX User Manual
XENYX 1204/1204FX User Manual
18
19
Download from Www.Somanuals.com. All Manuals Search And Download.
|