Installation Instructions
EUROLIGHT LD6230
Professional 6-Channel 10 A Dimmer Pack with DMX and Analog Control
Download from Www.Somanuals.com. All Manuals Search And Download.
3
EUROLIGHT LD6230 Installation Instructions
“Support”at behringer.com. If your country is not
listed, please check if your problem can be dealt with
by our“Online Support”which may also be found under
“Support”at behringer.com. Alternatively, please submit
an online warranty claim at behringer.com BEFORE
returning the product. All inquiries must be accompanied
by a description of the problem and the serial number
of the product. After verifying the product’s warranty
eligibility with the original sales receipt, MUSIC Group
will then issue a Return Materials Authorization
(“RMA”) number.
•
•
connection or operation of the unit in any way
that does not comply with the technical or safety
regulations applicable in the country where the
product is used;
(3) This warranty does not detract from the seller’s
obligations in regard to any lack of conformity of the
product and any hidden defect.
§ 9 Amendment
damage/defects caused by acts of God/Nature
(accident, fire, flood, etc) or any other condition that
is beyond the control of MUSIC Group.
Warranty service conditions are subject to change without
notice. For the latest warranty terms and conditions
and additional information regarding MUSIC Group’s
limited warranty, please see complete details online at
behringer.com.
(7) Any repair or opening of the unit carried out by
unauthorized personnel (user included) will void the
limited warranty.
* MUSIC Group Macao Commercial Offshore Limited of
Rue de Pequim No. 202-A, Macau Finance Centre 9/J, Macau,
including all MUSIC Group companies
(8) If an inspection of the product by MUSIC Group
shows that the defect in question is not covered by the
limited warranty, the inspection costs are payable by
the customer.
(2) Subsequently, the product must be returned in
its original shipping carton, together with the return
authorization number to the address indicated by
MUSIC Group.
(9) Products which do not meet the terms of this
limited warranty will be repaired exclusively at the buyer’s
expense. MUSIC Group or its authorized service center will
inform the buyer of any such circumstance. If the buyer
fails to submit a written repair order within 6 weeks after
notification, MUSIC Group will return the unit C.O.D. with
a separate invoice for freight and packing. Such costs will
also be invoiced separately when the buyer has sent in a
written repair order.
(3) Shipments without freight prepaid will not
be accepted.
§ 4 Warranty Exclusions
(1) This limited warranty does not cover consumable
parts including, but not limited to, fuses and batteries.
Where applicable, MUSIC Group warrants the valves or
meters contained in the product to be free from defects
in material and workmanship for a period of ninety (90)
days from date of purchase.
(10) MUSIC Group Authorized Resellers do not sell new
products directly in online auctions. Purchases made
through an online auction are on a“buyer beware”basis.
Online auction confirmations or sales receipts are not
accepted for warranty verification and MUSIC Group will
not repair or replace any product purchased through an
online auction.
(2) This limited warranty does not cover the product
if it has been electronically or mechanically modified
in any way. If the product needs to be modified or
adapted in order to comply with applicable technical
or safety standards on a national or local level, in any
country which is not the country for which the
product was originally developed and manufactured,
this modification/adaptation shall not be considered a
defect in materials or workmanship. This limited warranty
does not cover any such modification/adaptation,
regardless of whether it was carried out properly or not.
Under the terms of this limited warranty, MUSIC Group
shall not be held responsible for any cost resulting from
such a modification/adaptation.
§ 5 Warranty transferability
This limited warranty is extended exclusively to the
original buyer (customer of authorized reseller) and is
not transferable to anyone who may subsequently
purchase this product. No other person (reseller, etc.)
shall be entitled to give any warranty promise on behalf
of MUSIC Group.
(3) This limited warranty covers only the product
hardware. It does not cover technical assistance for
hardware or software usage and it does not cover
any software products whether or not contained in
the product. Any such software is provided“AS IS”
unless expressly provided for in any enclosed software
limited warranty.
§ 6 Claim for damage
Subject only to the operation of mandatory applicable
local laws, MUSIC Group shall have no liability to the buyer
under this warranty for any consequential or indirect
loss or damage of any kind. In no event shall the liability
of MUSIC Group under this limited warranty exceed the
invoiced value of the product.
(4) This limited warranty is invalid if the
factory-applied serial number has been altered or
removed from the product.
§ 7 Limitation of liability
This limited warranty is the complete and exclusive
warranty between you and MUSIC Group. It supersedes
all other written or oral communications related to this
product. MUSIC Group provides no other warranties for
this product.
(5) Free inspections and maintenance/repair work
are expressly excluded from this limited warranty,
in particular, if caused by improper handling of the
product by the user. This also applies to defects caused
by normal wear and tear, in particular, of faders,
crossfaders, potentiometers, keys/buttons, guitar strings,
illuminants and similar parts.
§ 8 Other warranty rights and
national law
(1) This limited warranty does not exclude or limit the
buyer’s statutory rights as a consumer in any way.
(6) Damage/defects caused by the following conditions
are not covered by this limited warranty:
(2) The limited warranty regulations mentioned herein
are applicable unless they constitute an infringement of
applicable mandatory local laws.
•
improper handling, neglect or failure to operate the
unit in compliance with the instructions given in
BEHRINGER user or service manuals;
Download from Www.Somanuals.com. All Manuals Search And Download.
4
EUROLIGHT LD6230 Installation Instructions
The BEHRINGER EUROLIGHT LD6230 Dimmer Pack was developed to meet
the highest demands of light engineering. Its wide-ranging functions
make it an all-purpose workhorse for various commercial applications
(TV studios, theatre or live events).
◊
Defective fuses must be replaced with fuses with identical rating!
The LD6230 is a Class I device in which a low-Ohm protective ground wire is an
integral part of its safety design.
During the installation, make sure that a low-Ohm protective conductor (< 0,1 Ohm)
exists between all bare metal parts and the grounding on the main connector.
The EUROLIGHT LD6230 has all the important features needed to control your
lighting equipment, yet its controls are clearly arranged and simple to use.
You can select between digital DMX or analog control. You get trouble-free
operation with the extensive LEDs used for signal error detection.
Output Channels
Phase
L1
CH 1*
CH 2
CH 3*
CH 4
CH 5*
CH 6
X
X
Important Information
L2
X
X
◊
Installation as well as initial operation must be performed by qualified
personnel. Always assure that your LD6230 is completely disconnected
from the mains before removing the casing cover.
L3
X
X
* Activation of control electronics and respective output channel
◊
◊
The LD6230 was designed for indoor use only.
Connector Terminal Strip
Please keep in mind that sudden temperature changes (e.g. bringing
your equipment from colder environments into warmer environments)
may cause condensation on electronic components, leading to possible
equipment damage and physical harm to the operator.
The connector terminal strip of your LD6230 is laid out for cables with diameters
between 0.326 mm2 (AWG 22) and 4 mm2 (AWG 12). When using flexible access
lines, cable end contacts corresponding to manufacturer specifications have to be
used. To assure good contact, skin the cable endings between 9 - 13 mm.
◊
◊
Please adhere to all applicable national safety standards
during installation.
During the installation, all applicable national standards need to be adhered to.
Please read the installation instructions and the enclosed user’s
manual in their entirety to familiarize yourself with the LD6230
and all of its functions. Please follow all instructions and store both
the installation instructions and the manual in a safe place for
future reference.
(2)
(2)
◊
◊
◊
Please assure that your EUROLIGHT is sufficiently cooled and that it is
not placed near heat sources that could cause overheating.
If you want to run your EUROLIGHT on mains voltage other than
factory-specified voltage, contact the nearest BEHRINGER service center.
(4)
To effectively limit harmonic currents and avoid voltage fluctuations that
could affect other electrical appliances, connect this equipment to an AC
outlet that complies with all applicable technical standards. In all other
cases, contact your local power supply provider for advice prior to usage.
(3)
(1)
Mains/Illuminant Connectors
To facilitate additional flexibility, your dimmer pack has a connector terminal
strip. Cable bushings for connecting to the mains and your illuminants are
located in the back. Flexibility is further enhanced with the option to retrofit a
CEE connector and a 16-pin HARTING connector.
Illustration: LD6230 connector terminal strip
When your LD6230 leaves the assembly plant, all incoming and outgoing
neutral conductor connectors (3) are bridged. The incoming phases L1/L1,
L2/L2 and L3/L3 (1) are always connected to one another in pairs and
switched to the overload protection of the channels 1 to 6. They protect output
connectors E1 to E6 (4). Each of the channels can handle currents of maximum
10 Amperes. The green-yellow conductors (2) (PE) may only be used as
protective conductors.
Both fixed and mobile installations require compliance with IEC 61010-1:2001
(EN 6110-1:2001). In particular, a 3-phase separator (pursuant IEC60947-1 and
IEC60947-3) needs to be included in the installation. This separator needs to be
labeled according to IEC 60417-50008 and IEC 0417-5007.
To assure compliance with Directive 89/336/EEC, only use specified upstream line
filters with your EUROLIGHT. Using it without line filters specified by BEHRINGER
may lead to electromagnetic interference. More detailed information on this
subject can be found at behringer.com.
The lowest cable gauge between L1 and L3, incoming neutral conductor (N)
and protective earth (PE) is 4 mm2 (AWG 12). For outgoing channels E1 to E6,
use cables with gauges corresponding to the loads used (2.5 mm2 (AWG 14)
or 1.5 mm2 (AWG 16)).
Safety and Initial Operation
Output assessment [A] Nominal cross section [mm2] (EU)
AWG (USA)
As soon as you connect your LD6230 to the mains, internal controls are activated.
The six automated fuses (circuit breakers) can all handle 10 A and serve as
overload protection for the connected equipment.
6-10
13-16
18-25
1.5
2.5
4
16
14
12
◊
Please keep in mind that activating circuit breakers 1, 2, 3, 4, 5 or 6 also
means that the respective channels can conduct voltage.
◊
During the installation, please adhere to all manufacturer instructions.
Regardless from mains supply voltage, the maximum output current of
the EUROLIGHT LD6230 is 10 A per dimmer circle.
Electronic controls are additionally protected with triple high-sensitivity fuses
located on the main board.
Download from Www.Somanuals.com. All Manuals Search And Download.
5
◊
EUROLIGHT LD6230 Installation Instructions
Please make sure that each dimmer load is connected to a separate
channel. Never connect more than one output to just one common
neutral conductor.
Specifications
Channels
◊
ATTENTION: Due to electrocution danger, do not use your dimmer pack
if there are bare cables visible.
Number
6
Load per channel
Maximal load per channel
Frequency
0.2 A min./10 A max.
10 A using a 3-phase connector
50/60 Hz
Connection Options for Flexible Usage
Output Connector (HARTING)
In the back of your LD6230 there is a cable bushing for connecting your
illuminants. Open the flap on the top of the LD6230 to get to the terminal clamps
used for this purpose. Here you have the option to retrofit a 16-pin HARTING
connector. To do that, you first have to remove the back-bearing cover sheet and
connect the HARTING connector to the terminal clamps.
Inputs
Power supply
3-phase connector, internal
terminal block/PG cable screw joint,
CEE connector (optional installation by
qualified personnel)
PIN assignment/HARTING connector
Analog
Digital
0 to +10 V via 8 pin DIN
DMX512 via XLR 5 pin
PIN 1 Phase channel 1
PIN 2 Phase channel 2
PIN 3 Phase channel 3
PIN 4 Phase channel 4
PIN 5 Phase channel 5
PIN 6 Phase channel 6
PIN 7 free
E1 PIN 9
E2 PIN 10
E3 PIN 11
E4 PIN 12
E5 PIN 13
E6 PIN 14
Neutral channel 1
Neutral channel 2
Neutral channel 3
Neutral channel 4
Neutral channel 5
Neutral channel 6
free
N
N
N
N
N
N
–
–
Outputs
Digital
Load
DMX512 via XLR 5 pin
–
–
PIN 15
PIN 16
Internal terminal block/PG cable screw
PIN 8 free
free
®
joint, HARTING (optional installation by
Ground wires need to be fastened to their respective PE connectors
qualified personnel)
CEE Power Supply Connector
System Fuses
Also located in the back is a cable bushing for the mains supply. Here, you can
retrofit a 5-pin CEE 32 A mains connector by removing the back-bearing cover
sheet and connect the CEE high-voltage connector to the connecting terminal.
The following illustration shows how the connections are allocated:
Load securing per channel
Control section fuse
10 A cable protection switch (type C)
2 x T 100 mA H/250 V 1 x T 160 mA
H/250 V for voltage range 220 - 230 V
(EU) 2 x T 160 mA H/250 V 1 x T 315 mA
H/250 V for voltage range 120 V (UL)
Power Supply
L3
N
L2
L1
Voltage
USA/Canada
120 V~, 60 Hz
240 V~, 50 Hz
3 x 20 A
Europe/U.K./Australia
Maximum power consumption
CEE connector pin allocation
Dimensions/Weight
◊
Removable mains connector cables with mains interconnections
Dimensions (H x W x D)
approx. 3 1/3 x 19 x 15 9/10"
approx. 84.3 x 482.6 x 403.8 mm
(pursuant IEC60320) must match the minimal load-carrying capacity
of the connector or must comply with the IEC60799 standard.
The interconnection and the cable must comply with prevalent
nominal values (maximal voltage and current).
Weight
approx. 21.6 lbs / 9.80 kg
BEHRINGER continuously strives to assure the highest quality standards possible. Required modifications may
be implemented without prior notice. Technical data and the appearance of the unit may deviate from the above
values and/or illustrations.
◊
During the installation, please adhere to the instructions provided by
the connector manufacturer.
Download from Www.Somanuals.com. All Manuals Search And Download.
6
EUROLIGHT LD6230 Installation Instructions
FEDERAL COMMUNICATIONS
COMMISSION COMPLIANCE
INFORMATION
EUROLIGHT LD6230
Responsible Party Name:
Address:
MUSIC Group Services US Inc.
18912 North Creek Parkway,
Suite 200 Bothell, WA 98011,
USA
Phone/Fax No.:
Phone: +1 425 672 0816
Fax: +1 425 673 7647
EUROLIGHT LD6230
complies with the FCC rules as mentioned in the following paragraph:
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC rules. Operation is subject to the
following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may
cause undesired operation.
Important information:
Changes or modifications to the equipment not expressly approved by MUSIC Group
can void the user’s authority to use the equipment.
Technical specifications and appearances are subject to change without notice and accuracy is not guaranteed. BEHRINGER is part of the MUSIC Group (music-group.com). All trademarks are the property of their respective owners. MUSIC Group
accepts no liability for any loss which may be suffered by any person who relies either wholly or in part upon any description, photograph or statement contained herein. Colors and specifications may VARY FROM ACTUAL PRODUCT. MUSIC Group
products are sold through authorized FULLFILLERS AND RESELLERS only. FULLFILLERS AND RESELLERS are not agents of MUSIC Group and have absolutely no authority to bind MUSIC Group by any express or implied undertaking or representation.
This manual is copyrighted. No part of this manual may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying and recording of any kind, for any purpose, without the express written permission of
MUSIC Group IP Ltd. ALL RIGHTS RESERVED. © 2012 MUSIC Group IP Ltd. Trident Chambers, Wickhams Cay, P.O. Box 146, Road Town, Tortola, British Virgin Islands
Download from Www.Somanuals.com. All Manuals Search And Download.
|