Barco Home Theater Screen R9000740 User Manual
BARCO PROJECTION SYSTEMS  
VISION  
701 MULTIMEDIA  
R9000740  
OWNER'S MANUAL  
Date:  
070597  
Rev. :  
01  
Art. No.  
R5975238  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TABLE OF CONTENTS  
WARNINGS ........................................................................................................ 1-1  
SAFETY INSTRUCTIONS ................................................................................... 1-1  
On safety .................................................................................................... 1-4  
Oninstallation ............................................................................................. 1-5  
On servicing ............................................................................................... 1-6  
Oncleaning ................................................................................................ 1-6  
On repacking .............................................................................................. 1-7  
Onillumination ............................................................................................ 1-7  
LOCATION AND FUNCTION OF CONTROLS ...................................................2-1  
Rear panel terminology ..............................................................................2-2  
Front panel terminology ..............................................................................2-3  
Control panel terminology ...........................................................................2-4  
a. The local keypad ....................................................................................2-4  
b. RCU control panel terminology ...............................................................2-4  
POWER (MAINS) CONNECTION .......................................................................3-1  
Switching on/off ..........................................................................................3-2  
Power (mains) cord connection ..................................................................3-2  
SOURCE CONNECTIONS .................................................................................4-1  
Signal input connection to the projector : ....................................................4-2  
Connecting a Composite Video source. ......................................................4-3  
Connecting a S-Video source. ....................................................................4-4  
Connecting a RGB Analog source with composite sync. .............................4-5  
Connecting a RGB Analog source with Tri-level sync. ................................4-7  
Connecting a Component source................................................................4-8  
Connecting a Component source with Tri-level sync. ..................................4-9  
Connecting a computer, e.g. IBM PC (or compatible), Apple Macintosh to  
the RS232 input of the projector. .............................................................. 4-11  
Connecting a RCVDS 05 switcher to the projector. ..................................... 4-12  
Connecting a VS05 switcher to the projector. ............................................. 4-12  
Connecting an IR Remote Receiver to the projector .................................. 4-12  
Peripheralequipment ................................................................................ 4-12  
CONTROLLING ..................................................................................................5-1  
Battery installation in the RCU. ...................................................................5-2  
How to use your RCU .................................................................................5-3  
Projector address .......................................................................................5-5  
How to display a projector address? ...........................................................5-5  
How to program an address into the RCU? .................................................. 5-6  
Inputselection ............................................................................................. 5-6  
Picturecontrols ........................................................................................... 5-8  
The Pause key. ......................................................................................... 5-11  
START UP OF THE ADJUSTMENT MODE ........................................................6-1  
Entering the adjustment mode ....................................................................6-2  
Adjustment mode .......................................................................................6-3  
1
R5975238 BARCOVISION 701 MULTIMEDIA 070597  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TABLE OF CONTENTS  
GUIDED ADJUSTMENT MODE ..........................................................................7-1  
Start up of the guided adjustment mode. ......................................................7-2  
Overview flowchart 'Guided Adjustment' procedure. .....................................7-3  
SelectingSetupPattern ...............................................................................7-4  
Internal Cross Hatch Pattern .......................................................................7-5  
Picturetuning ..............................................................................................7-6  
Sync Fast/Slow toggle .................................................................................7-6  
Line Doubler (option) ...................................................................................7-6  
Enhanced blue ON/OFF ..............................................................................7-7  
Raster Centering on Green CRT Faceplate ..................................................7-8  
Shifting Red and Blue on Green ................................................................. 7-10  
Left-Right(East-West)Adjustments ........................................................... 7-10  
Vertical Centerline Bow Adjustment ........................................................... 7-11  
Vertical Centerline Skew Adjustment.......................................................... 7-11  
RightKeystoneAdjustment ....................................................................... 7-12  
LeftKeystoneAdjustment .......................................................................... 7-12  
Right Bow Adjustment ............................................................................... 7-12  
Left Bow Adjustment ................................................................................. 7-13  
HorizontalSizeAdjustment ........................................................................ 7-13  
Top-Bottom(North-South)Adjustments...................................................... 7-14  
Horizontal Centerline Skew Adjustment...................................................... 7-15  
Horizontal Centerline Bow Adjustment ....................................................... 7-15  
TopKeystoneAdjustment.......................................................................... 7-15  
Top Bow Adjustment ................................................................................. 7-16  
BottomKeystoneAdjustment ..................................................................... 7-16  
Bottom Bow Adjustment ............................................................................ 7-16  
Size-linearityAdjustment ........................................................................... 7-17  
VerticalLinearityAdjustment ..................................................................... 7-17  
VerticalSizeAdjustment ............................................................................ 7-18  
HorizontalPhaseAdjustment ..................................................................... 7-19  
ConvergenceAdjustment .......................................................................... 7-20  
BlankingAdjustment.................................................................................. 7-21  
Topblankingadjustment ............................................................................ 7-22  
Bottomblankingadjustment ....................................................................... 7-22  
Leftblankingadjustment ............................................................................ 7-23  
Rightblankingadjustment.......................................................................... 7-23  
ColorBalance ........................................................................................... 7-24  
RANDOM ACCESS ADJUSTMENT MODE ....................................................... 8-1  
Starting up the random access adjustment mode. ..................................... 8-2  
Overview flowchart 'Random Access Adjustment' mode ............................ 8-3  
Selecting Setup Pattern ............................................................................. 8-5  
Internal Cross Hatch Pattern ..................................................................... 8-6  
Random Access Adjustment Mode Selection menu. .................................. 8-6  
Picture tuning ............................................................................................ 8-7  
Color Balance ............................................................................................ 8-7  
Sync Fast/Slow Adjustment .........................................................................8-8  
Linedoubler ................................................................................................8-9  
Enhanced Blue On/Off Adjustment...............................................................8-9  
Color Select .............................................................................................. 8-10  
2
R5975238 BARCOVISION 701 MULTIMEDIA 070597  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TABLE OF CONTENTS  
GeometryAdjustments .............................................................................. 8-11  
HorizontalPhaseAdjustment ..................................................................... 8-12  
RasterShiftAdjustment ............................................................................. 8-14  
Left-Right(east-west)Adjustments ............................................................ 8-16  
Top-Bottom(north-south)Adjustments ....................................................... 8-18  
HorizontalSizeAdjustment ........................................................................ 8-20  
VerticalLinearityAdjustment ..................................................................... 8-21  
VerticalSizeAdjustment ............................................................................ 8-22  
BlankingAdjustments ................................................................................ 8-23  
ConvergenceAdjustments ........................................................................ 8-25  
SERVICE MODE ................................................................................................9-1  
Starting up the Service mode. ....................................................................9-2  
Overview flowchart 'Service' mode. .............................................................. 9-3  
Projector set up ........................................................................................... 9-4  
Identification ............................................................................................... 9-4  
Total run time .............................................................................................. 9-5  
Changepassword ....................................................................................... 9-6  
Changelanguage ........................................................................................ 9-7  
Change projector address ........................................................................... 9-8  
Changebaudrate ........................................................................................ 9-8  
Power up mode ........................................................................................... 9-9  
BARCO logo ............................................................................................. 9-10  
Memorymanagement................................................................................ 9-11  
Copy a block ............................................................................................. 9-11  
Deletion of blocks ...................................................................................... 9-12  
Deleting block by block .............................................................................. 9-13  
Deletion of all blocks ................................................................................. 9-14  
All settings to midposition .......................................................................... 9-14  
Undo all settings to midpos ........................................................................ 9-15  
R & B convergence mid ............................................................................. 9-15  
Undo R & B convergence mid .................................................................... 9-16  
Switch green convergence off .................................................................... 9-16  
Switch green convergence on .................................................................... 9-17  
Commonsettings ...................................................................................... 9-17  
G2adjustment .......................................................................................... 9-18  
CRT run in cycle ....................................................................................... 9-19  
Projector warm up ..................................................................................... 9-20  
I2CDiagnostics ........................................................................................ 9-21  
MESSAGES, WARNINGS AND FAILURES ....................................................... 10-1  
OPTIONS ......................................................................................................... 11-1  
IR Receiver 800 ....................................................................................... 11-2  
Hardwired RCU ........................................................................................ 11-2  
ProjectorControlsoftware ......................................................................... 11-3  
RCVDS 05 ................................................................................................ 11-3  
VS05 ........................................................................................................ 11-3  
Adapter and communication cables ........................................................... 11-3  
Ceiling mount CM50 .................................................................................. 11-4  
3
R5975238 BARCOVISION 701 MULTIMEDIA 070597  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TABLE OF CONTENTS  
OrbitingKit ................................................................................................ 11-4  
Soft edge matching kit ............................................................................... 11-4  
Contrastmodulationkit .............................................................................. 11-4  
Appendix A : Battery replacement in the RCU. ................................................... A-1  
Appendix B : Orbiting .......................................................................................... B-1  
Appendix C : Soft edge matching ........................................................................ C-1  
Appendix D : Contrast modulation (option) ........................................................... D-1  
Appendix E : Adjustment Blocks (memory blocks) ............................................... E-1  
Appendix F : Source numbers 90 - 99 ................................................................. F-1  
4
R5975238 BARCOVISION 701 MULTIMEDIA 070597  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SAFETY INSTRUCTIONS  
WARNINGS  
SAFETY INSTRUCTIONS  
on safety  
on installation  
on servicing  
on cleaning  
on repacking  
on illumination  
R5975238 BARCOVISION 701 MULTIMEDIA 070497  
1-1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SAFETY INSTRUCTIONS  
Notice on Safety  
Thisequipmentisbuiltinaccordancewiththerequirementsoftheinternationalsafety  
standardsEN60950,UL1950andCSAC22.2No.950,whicharethesafetystandards  
ofinformationtechnologyequipmentincludingelectricalbusinessequipment.  
These safety standards impose important requirements on the use of safety critical  
components, materials and isolation, in order to protect the user or operator against  
risk of electric shock and energy hazard, and having access to live parts.  
Safety standards also impose limits to the internal and external temperature rises,  
radiationlevels,mechanicalstabilityandstrength,enclosureconstructionandprotec-  
tion against the risk of fire.  
Simulatedsinglefaultconditiontestingensuresthesafetyoftheequipmenttotheuser  
even when the equipment's normal operation fails.  
INSTALLATION INSTRUCTIONS  
Before operating this equipment please read this manual thoroughly, and  
retain it for future reference.  
Installation and preliminary adjustments should be performed by qualified  
BARCO personnel or by authorized BARCO service dealers.  
OWNER’S RECORD  
The part number and serial number are located at the left side of the projector.  
Record these numbers in the spaces provided below. Refer to them whenever you  
call upon your BARCO dealer regarding this product.  
PART NUMBER :  
SER. NUMBER :  
DEALER :  
R5975238 BARCOVISION 701 MULTIMEDIA 070497  
1-2  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SAFETY INSTRUCTIONS  
The lightning flash with an arrowhead within a triangle is  
intended to tell the user that parts inside this product may cause  
a risk of electrical shock to persons.  
Theexclamationpointwithinatriangleisintendedtotelltheuser  
that important operating and/or servicing instructions are in-  
cluded in the technical documentation for this equipment.  
WARNING  
TO PREVENT FIRE OR ELECTRICAL SHOCK HAZARD, DO  
NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE  
FEDERAL COMMUNICATION COMMISSION (FCC STATEMENT)  
This equipment has been tested and found to comply with the limits of a class A  
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to  
provide reasonable protection against harmful interference when the equipment is  
operated in a commercial environment. This equipment generates, uses and can  
radiate radio frequency energy and, if not installed and used in accordance with the  
instruction manual, may cause harmful interference to radio communications.  
Operation of this equipment in a residential area is likely to cause harmful  
interference in which case the user will be required to correct the interference at his  
own expense.  
R5975238 BARCOVISION 701 MULTIMEDIA 070497  
1-3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SAFETY INSTRUCTIONS  
* All the safety and operating instructions should be read before using this unit.  
*Thesafetyandoperatinginstructionsmanualshouldberetainedforfuturereference.  
*Allwarningsontheequipmentandinthedocumentationmanualsshouldbeadhered  
to.  
* All instructions for operating and use of this equipment must be followed precisely.  
On safety  
1. This product should be operated from an AC power source  
Operating AC power voltage of the projector:  
BARCOVISION 701 MULTIMEDIA  
Art.No. R9000740 (230V AC)  
The projector leaves the factory for 230 Vac. Consult your dealer to switch over to  
120 Vac.  
If you are not sure of the type of AC power available, consult your dealer or local  
power company.  
2. This product is equipped with a 3-wire grounding plug, a plug having a third  
(grounding) pin. This plug will only fit into a grounding-type power outlet. This is a  
safetyfeature.Ifyouareunabletoinserttheplugintotheoutlet,contactyourelectrician  
toreplaceyourobsoleteoutlet.Donotdefeatthepurposeofthegrounding-typeplug.  
WARNING FOR THE CUSTOMERS: THIS APPARATUS MUST BE GROUNDED  
(EARTHED) via the supplied 3 conductor AC power cable.  
(If the supplied power cable is not the correct one, consult your dealer.)  
A. Mains lead (Power cord) with CEE 7 plug:  
The wires of the mains lead are colored in accordance with the following code.  
Green and yellow:  
Blue:  
earth (safety earth)  
neutral  
Brown:  
line (live)  
R5975238 BARCOVISION 701 MULTIMEDIA 070497  
1-4  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SAFETY INSTRUCTIONS  
B. Power cord with ANSI 73.11 plug:  
The wires of the power cord are colored in accor-  
dance with the following code.  
Green/yellow: ground  
White:  
Black:  
neutral  
line (live)  
3. Do not allow anything to rest on the power cord. Do not locate this product where  
persons will walk on the cord.  
To disconnect the cord, pull it out by the plug. Never pull the cord itself.  
4.Ifanextensioncordisusedwiththisproduct,makesurethatthetotaloftheampere  
ratings on the products plugged into the extension cord does not exceed the  
extension cord ampere rating. Also make sure that the total of all products plugged  
into the wall outlet does not exceed 15 amperes.  
5. Never push objects of any kind into this product through cabinet slots as they may  
touch dangerous voltage points or short out parts that could result in a risk of fire or  
electrical shock.  
Never spill liquid of any kind on the product. Should any liquid or solid object fall into  
the cabinet, unplug the set and have it checked by qualified service personnel before  
resuming operations.  
6. Lightning - For added protection for this video product during a lightning storm, or  
when it is left unattended and unused for long periods of time, unplug it from the wall  
outlet. This will prevent damage to the projector due to lightning and AC power-line  
surges.  
Oninstallation  
1. Do not place this equipment on an unstable cart, stand, or table. The product may  
fall, causing serious damage to it.  
2. Do not use this equipment near water.  
3. Slots and openings in the cabinet and the back or bottom are provided for  
ventilation; to ensure reliable operation of the product and to protect it from  
overheating, these openings must not be blocked or covered. The openings should  
never be blocked by placing the product on a bed, sofa, rug, or other similar surface.  
R5975238 BARCOVISION 701 MULTIMEDIA 070497  
1-5  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SAFETY INSTRUCTIONS  
This product should never be placed near or over a radiator or heat register.  
Theprojectorshouldnotbeplacedinabuilt-ininstallationorenclosureunlessproper  
ventilationisprovided.  
Onservicing  
Do not attempt to service this product yourself, as opening or removing covers may  
expose you to dangerous voltage potentials and risk of electric shock!  
Refer all servicing to qualified service personnel.  
Unplugthisproductfromthewalloutletandreferservicingtoqualifiedservice  
personnel under the following conditions:  
a. When the power cord or plug is damaged or frayed.  
b. If liquid has been spilled into the equipment.  
c.If the product has been exposed to rain or water.  
d. If the product does not operate normally when the operating instructions are  
followed.  
Note : Adjust only those controls that are covered by the operating instructions since  
improperadjustmentoftheothercontrolsmayresultindamageandwilloftenrequire  
extensive work by a qualified technician to restore the product to normal operation.  
e. If the product has been dropped or the cabinet has been damaged.  
f. If the product exhibits a distinct change in performance, indicating a need for  
service.  
Replacement parts - When replacement parts are required, be sure the service  
technician has used original BARCO replacement parts or authorized replacement  
parts which have the same characteristics as the BARCO original part. Unauthor-  
ized substitutions may result in degraded performance and reliability, fire, electric  
shock or other hazards. Unauthorized substitutions may void warranty.  
Safety check - Upon completion of any service or repairs to this projector, ask the  
servicetechniciantoperformsafetycheckstodeterminethattheproductisinproper  
operating condition.  
On cleaning  
Unplug this product from the wall outlet before cleaning. Do not use liquid  
cleaners or aerosol cleaners. Use a damp cloth for cleaning.  
-Tokeepthecabinetlookingbrand-new,periodicallycleanitwithasoftcloth.Stubborn  
stains may be removed with a cloth lightly dampened with mild detergent solution.  
Never use strong solvents, such as thinner or benzine, or abrasive cleaners, since  
these will damage the cabinet.  
R5975238 BARCOVISION 701 MULTIMEDIA 070497  
1-6  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SAFETY INSTRUCTIONS  
-Toensurethehighestopticalperformanceandresolution,theprojectionlensesare  
specially treated with an anti-reflective coating, therefore, avoid touching the lens.  
To remove dust on the lens, use a soft dry cloth. Do not use a damp cloth, detergent  
solution, or thinner.  
Onrepacking  
Save the original shipping carton and packing material; they will come in handy if you  
everhavetoshipyourequipment.Formaximumprotection,repackyoursetasitwas  
originally packed at the factory.  
Onillumination  
In order to obtain the best quality for the projected image, it is essential that the  
ambient light which is allowed to fall on the screen be kept to an absolute minimum.  
When installing the projector and screen, care must be taken to avoid exposure to  
ambient light directly on the screen. Avoid adverse illumination on the screen from  
direct sunlight or fluorescent lighting fixtures.  
The use of controlled ambient lighting, such as incandescent spot light or a dimmer,  
is recommended for proper room illumination. Where possible, care should also be  
taken to ensure that the floors and walls of the room in which the projector is to be  
installed are non-reflecting, dark surfaces. Brighter surfaces will tend to reflect and  
diffuse the ambient light and hence reduce the contrast of the projected image on the  
screen.  
R5975238 BARCOVISION 701 MULTIMEDIA 070497  
1-7  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SAFETY INSTRUCTIONS  
R5975238 BARCOVISION 701 MULTIMEDIA 070497  
1-8  
Download from Www.Somanuals.com. All Manuals Search And Download.  
LOCATION AND FUNCTION OF CONTROLS  
LOCATION AND FUNCTION OF CONTROLS  
Rear Panel Terminology  
Front Panel Terminology  
RCUTerminology  
R5975238BARCOVISION701MULTIMEDIA070497  
2-1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
LOCATION AND FUNCTION OF CONTROLS  
REAR PANEL TERMINOLOGY  
CO MM PO RT  
(800 peripherals)  
R
G( S)  
Y(S)  
B
B-Y  
RS232 IN  
RS23 2OUT  
I
R
S- VI DEO  
R EM OT  
E
S
VID EO  
R
-
Y
5
1
4
8
2
3
6
7
RS232IN  
1
2
Connection between the BARCOVISION 701 MULTIMEDIA and an IBM  
PC (or compatible) or MAC (RS422) for remote computer control and data  
communication.  
RS232OUT  
Used to connect to the next projector, RS232IN plug  
(communication link for PC or MAC to the next projector)  
IR sensor  
3
4
receiver for control signals transmitted from the RCU.  
Communication port (800 peripherals)  
* allows communication between the RCVDS switcher and the projector.  
* allows connection of a remote IR receiver unit to the projector.  
* allows connection of an IRIS 800 to converge the image automatically.  
IR Remote  
remote input for wired remote control  
5
6
RGB-S IN or (R-Y)Y(B-Y)-S IN (4x BNC connector):  
RGB-S in : allows a character generator, microcomputer, video camera,  
etc. having analog RGB output to be connected to the projector.  
Line inputs:  
- signals RED-GREEN-BLUE  
- COMPOSITE sync. signal  
(R-Y)Y(B-Y)-S IN (component in):allows to connect e.g. a professional  
VCR having component outputs to the projector.  
Line inputs  
- signals RED-LUMA, LUMA, BLUE-LUMA  
- COMPOSITE sync. signal  
R5975238BARCOVISION701MULTIMEDIA070497  
2-2  
Download from Www.Somanuals.com. All Manuals Search And Download.  
LOCATION AND FUNCTION OF CONTROLS  
VIDEO IN (Composite video, 1x BNC connector): allows a video tape  
recorder, video camera, color receiver/monitor, etc. having video line  
output to be connected to the projector.  
7
S-VIDEO IN: Separated Y/C (luma-chroma) signal inputs and outputs  
for higher quality playback of Super VHS signals (4-pin S-VIDEO  
connector).  
8
FRONT PANEL TERMINOLOGY  
1
2
3
4
AUTODIAGNOSIS DISPLAY  
LED indication for service purposes.  
1
POWER (MAINS) SWITCH : press the switch to turn the projector ON.  
2
Depending on the hardware set-up of the projector during installation,  
the projector switches to ‘standby’ or to ‘operational mode’. If in  
standby, the standby led in the autodiagnosisdisplay lights up.  
POWER (MAINS) INPUT: Connect the supplied ac power (mains) cord  
here and to wall the outlet.  
3
4
IR SENSOR  
receiver for control signals transmitted from the RCU700.  
R5975238BARCOVISION701MULTIMEDIA070497  
2-3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
LOCATION AND FUNCTION OF CONTROLS  
Control panel terminology  
a. The local keypad  
Getting access  
The local keypad is covered by a door on  
which the projector logo is screened.  
S
TANDBY  
E
NTER  
To open this door, push as indicated on next drawing and turn it to the front side of  
the projector.  
b. RCU control panel terminology  
This remote control includes a battery powered infrared (IR) transmitter that allows  
the user to control the projector remotely.  
This remote control is used for source selection, control, adaptation and set-up. It  
includes automatic storing of :  
- picture controls (Brightness, Sharpness,....)  
- picture geometry adjustments  
- convergence adjustments  
Other functions of the remote control are:  
- switching between standby and operational modes  
- switching to "pause" (blanked picture, full power for immediate restarting)  
- direct access to all connected sources  
- variable adjustment speed : when pushing continuously on the arrow keys or the  
picture keys, the adjustment will be executed in an accelerated fashion.  
R5975238BARCOVISION701MULTIMEDIA070497  
2-4  
Download from Www.Somanuals.com. All Manuals Search And Download.  
LOCATION AND FUNCTION OF CONTROLS  
RCU  
Local keypad  
12  
2
10  
ADJ US T  
EXIT  
S T AND BY  
E N TE R  
1 1  
1 0  
9
1
2
EXIT  
ADJ  
ENTER  
3
4
5
STBY  
PAUSE  
TEXT  
4
1 1  
9
8
7
+
-
-
-
0
9
7
SHARPNESS  
+
+
+
8
6
4
TINT  
6
5
3
1
COLOR  
stand-by  
-
BRIGHTNESS  
pause/park  
+
-
2
CONTRAST  
sharpness  
tint  
color  
32 c  
brightness  
contrast  
R5975238BARCOVISION701MULTIMEDIA070497  
2-5  
Download from Www.Somanuals.com. All Manuals Search And Download.  
LOCATION AND FUNCTION OF CONTROLS  
Backlightkey:whenactivated,allkeyswillbelitupandvisibleinthedark.  
ADJ. : adjust key, to enter or exit the adjustment mode.  
1
2
3
Address key (sunk key), to enter the address of the projector (between  
0 and 9). Press the address key, followed by pressing one digit button  
between 0 and 9.  
STBY : stand by button : - to initiate remote power up operation  
4
5
6
7
8
- to stop projection without main power off.  
Pause :to blank the image, press PAUSE. The image disappears but full  
power is retained for immediate restarting.  
Digit buttons : direct input selection.  
Picture controls : use these buttons to obtain the desired level (see also  
'Controlling') for each picture function.  
TEXT : when adjusting one of the image controls during a meeting, the  
displayed bar scale can be removed by pressing 'TEXT' key first. To re-  
display the bar scale on the screen, press 'TEXT' key again. 'TEXT' key  
is only active in operational mode. When 'TEXT' is off, no warning  
message will be displayed.  
ENTER : to start up the adjustment mode or to confirm an adjustment or  
selection in the adjustment mode.  
9
EXIT : to leave the adjustment mode or to scroll upwards when in the  
10  
11  
adjustment mode.  
Control disk : to make menu selections when in the adjustment mode.  
Also allows to increment or decrement an adjustment in the adjustment  
mode.  
control disk up = up arrow in the menus  
control disk down = down arrow in the menus  
control disk to the right = arrow to the right on the menus  
control disk to the left = arrow to the left on the menus  
RC operating indication : lights up when a button on the remote control  
is pressed. (This is a visual indicator to check the operation of the remote  
control)  
12  
R5975238BARCOVISION701MULTIMEDIA070497  
2-6  
Download from Www.Somanuals.com. All Manuals Search And Download.  
POWER CONNECTION  
POWER (MAINS) CONNECTION  
R59 75456 BARCOVISION 701 MULTIMEDIA 070497  
3-1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
POWER CONNECTION  
Power (mains) cord connection  
Use the supplied power cord to connect your projector to the wall outlet. Plug the  
female power connector into the male connector at the front of the projector.  
See installation instructions before  
connecting to the supply  
V
I
NOM 120/230 Volt  
MAX 5/2.5 AMP  
FREQ 60/50 Hz  
O N  
OFF  
See installation instructions before  
connecting to the supply  
V NOM 120/230 Volt  
I MAX  
FREQ  
5/2.5 AMP  
60/50 Hz  
O N  
O F F  
Switching on/off  
The projector is switched ON and OFF using the power (mains) switch ON/OFF.  
Pressed : ON  
Not pressed : OFF  
The projector can start now in the 'operational mode' (image displayed) or in the  
'stand by mode', depending on the position of the 'power up' dip switch on the  
controller unit. This DIP switch is set during installation by a qualified technician.  
If you want to change this start up mode, call a qualified technician.  
Stand by indication lamp :  
no light up : projector in operational mode  
red : projector is in stand by.  
Leds on the front plate of the projector  
3-2  
R5975238 BARCOVISION 701 MULTIMEDIA 070497  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CONNECTIONS  
SOURCE CONNECTIONS  
- connecting a Video source  
- connecting a S-Video source  
- connecting a RGsB or RGBS analog source  
- connecting a RG3sB or RGB3S analog source  
- connecting a (R-Y)Ys(B-Y) or (R-Y)Y(B-Y)S analog source  
-connectinga(R-Y)Y3s(B-Y)or(R-Y)Y(B-Y)3Sanalogsource  
PERIPHERAL EQUIPMENT CONNECTION  
-Connectingacomputer, e.g. IBMPC(orcompatible), Apple  
Macintosh to the RS232 input of the projector.  
- connecting a RCVDS 05  
- connecting a VSO5  
- connecting an IR Remote Receiver  
R5975238 BARCOVISION 701 MULTIMEDIA 280497  
4-1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CONNECTIONS  
Signal input connection to the projector :  
- Composite Video (*)  
- S-Video (*)  
- RGBS or RGsB  
- RGB3S or RG3sB  
- (R-Y)Y(B-Y)S or (R-Y)Ys(B-Y) [component input] (**)  
- (R-Y)Y(B-Y)3S or (R-Y)Y3s(B-Y) [component input] (**)  
(*) If the line douoble feature is built in, this feature is available via a software on/off toggle.  
(**) If the line double feature is built in, this feature is available for component video signals on standard  
frequency via software on/off toggle.  
COMM PORT  
(800 peripherals)  
R
G(S)  
(S  
B
B-Y  
S-VI DEO  
REMOTE  
S
VI DEO  
R
-
Y
Y
)
RS232 OUT  
RS232 IN  
3
1
2
Source No Projector input  
Pressdigitbutton  
1
2
3
4
5
Comp. Video  
S-Video*  
1
2
3
4
RGBS or RGsB**  
RGB3S or RG3sB***  
(R-Y)Y(B-Y)S or  
(R-Y)Ys(B-Y)****  
5
6
6
(R-Y)Y(B-Y)3Sor  
(R-Y)Y3s(B-Y)*****  
*
Input signal Y/C (luma/chroma)  
**  
Input signal : R, G and B with composite sync on G or separate composite  
sync  
***  
****  
Input signal : R, G and B with Tri level sync on G or separate Tri level sync.  
Input signal : R-Y, Y and B-Y with composite sync on Y or separate  
composite sync  
*****  
Input signal : R-Y, Y and B-Y with Tri level sync on Y or separate Tri level  
sync.  
R5975238 BARCOVISION 701 MULTIMEDIA 280497  
4-2  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CONNECTIONS  
Connecting a Composite Video source.  
Composite video signals from a VCR, OFF air signal decoder, etc..  
If a line doubler is built in :  
the default position of this line doubler is ON (active), the video input signal  
will be displayed as a non interlaced image (= improved image stability).  
To enable or to disable this line doubler function, enter the adjustment mode  
and change the position of the ON/OFF toggle switch (see Picture tuning in  
chapter 'Guided' adjustment mode or 'Random access' adjustment mode).  
COMM PORT  
(800 peripherals)  
R
G(S)  
Y(S)  
B
S-VI DEO  
REMO TE  
S
VI DEO  
RS232 IN  
RS2 32  
O
UT  
R
-
Y
B-Y  
C om po si te  
v id e o  
Audio amplifier  
TV tuner, e.g. TVDM40 stereo  
V C R  
Video input selection :  
a. Press digit button 1 on the RCU or  
b. with the local keypad :  
(to gain access to the local keypad, see Local keypad in chapter Location and  
function of control.)  
- press ADJUST key, the General access menu is displayed on the screen.  
R5975238 BARCOVISION 701 MULTIMEDIA 280497  
4-3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CONNECTIONS  
- use the control disk to high-  
light 1.  
- press ENTER to select the  
highlighted source.  
GENERAL ACCESS  
S H A R P N E S S  
TI N T  
C O L O R  
B R I G H TN E S S  
C O N T R A S T  
5
3
1
6
4
2
En ter A DJU ST  
Select with  
,
or  
then <ENTER>.  
<EXIT> to return  
Connecting a S-Video source.  
Separate Y-luma/C-chroma signals for higher quality playback of Super VHS  
signals.  
If a line doubler is built in :  
the default position of this line doubler is ON (active), the video input signal  
will be displayed as a non interlaced image (= improved image stability).  
To enable or to disable this line doubler function, enter the adjustment mode  
and change the position of the ON/OFF toggle switch (see Picture tuning in  
chapter 'Guided' adjustment mode or 'Random access' adjustment mode).  
COMM PORT  
(800 peripherals)  
R
G
Y(S)  
(S)  
B
B-Y  
S- VID EO  
REMO TE  
S
VI DEO  
RS2 32  
O
UT  
RS23 2 IN  
R
-
Y
L u m a / C h r o m a  
VCR S-VHS  
Audio amplifier  
R5975238 BARCOVISION 701 MULTIMEDIA 280497  
4-4  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CONNECTIONS  
S-Video input selection  
a. Press digit button 2 on the RCU or  
b. with the local keypad :  
(to gain access to the local keypad, see Local keypad in chapter Location and  
functions of control.)  
- Press ADJUST key, the General access menu is displayed on the screen.  
- Use the control disk to  
highlight2.  
- Press ENTER to select  
GENERAL ACCESS  
thehighlightedsource.  
S H A RP N E S S  
TI N T  
C O L O R  
B R IG H TNE S S  
C O N TR A S T  
5
3
1
6
4
2
En ter ADJU ST  
Select with  
,
or  
then <ENTER>.  
<EXIT> to return  
Connecting a RGB Analog source with composite sync.  
RGB analog input terminals with composite sync input or with sync on green. The  
projector detects automatically where the sync signal is located.  
Always use an interface when a computer and local monitor have to be connected  
to the projector. Examples of interfaces which can be applied :  
Universal analog interface  
RGB 120 MHz Analog Interface  
Multifunctional Analog Interface Kit  
(MAGIK)  
R9826100  
R9826570 (230V)  
R9828120 (230V)  
R9828129 (120V)  
R9828070 (230V)  
R9828079 (120V)  
R9828050 (230V)  
R9828059(120V)  
VGA interface  
MAC interface  
R5975238 BARCOVISION 701 MULTIMEDIA 280497  
4-5  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CONNECTIONS  
COMM PORT  
(800 peripherals)  
R
G( S)  
Y(S)  
B
B-Y  
S-VI DEO  
R
E
M
O
T
E
S
VI DEO  
RS232 OUT  
R
-
Y
RS23 2 IN  
AN AL OG  
G
O
UT  
B
R
S
I NPU T  
RGBS or RGsB input selection  
a. Press digit button 3 on the RCU or  
b. With the local keypad :  
(to gain access to the local keypad, see Local keypad in chapter Location and  
functions of control.)  
- Press ADJUST key, the General access menu is displayed on the screen.  
-Usethecontroldisktohigh-  
light 3.  
GENERAL ACCESS  
- Press ENTER to select the  
highlighted source.  
S H A RP N E S S  
TI N T  
C O L O R  
B R IG H TNE S S  
C O N TR A S T  
5
3
1
6
4
2
En ter ADJU ST  
Select with  
,
or  
then <ENTER>.  
<EXIT> to return  
R5975238 BARCOVISION 701 MULTIMEDIA 280497  
4-6  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CONNECTIONS  
Connecting a RGB Analog source with Tri-level sync.  
RGBanaloginputterminalswithTrilevelsyncinputorwithTri-levelsyncongreen.  
The projector detects automatically where the sync signal is located.  
COMM PORT  
R
G
(S)  
B
B-Y  
S-VI DEO  
REMO TE  
(800 peripherals)  
S
VI DEO  
RS2 32  
O
UT  
RS232 IN  
R
-
Y
Y(S)  
VCR HDTV player  
Audio amplifier  
RGB3S or RG3sB input selection  
a. Press digit button 4 on the RCU or  
b. With the local keypad :  
(to gain access to the local keypad, see Local keypad in chapter Location and  
functions of control.)  
- Press ADJUST key, the General access menu is displayed on the screen.  
- Use the control disk to high-  
light 4.  
GENERAL ACCESS  
- Press ENTER to select the  
highlighted source.  
S H A RP N E S S  
TI N T  
C O L O R  
B R IG H TNE S S  
C O N TR A S T  
5
3
1
6
4
2
En ter ADJU ST  
Select with  
,
or  
then <ENTER>.  
<EXIT> to return  
R5975238 BARCOVISION 701 MULTIMEDIA 280497  
4-7  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CONNECTIONS  
Connecting a Component source.  
(R-Y)Y(B-Y) analog input terminals with sync input or with sync on the luminance  
(Y) input. The projector detects automatically where the sync signal is located.  
Line doubling is possible for component video input sources on standard line  
frequency.  
If a line doubler is built in :  
the default position of this line doubler is ON (active), the component video input  
signal will be displayed as a non interlaced image (= improved image stability).  
To enable or to disable this line doubler function, enter the adjustment mode and  
change the position of the ON/OFF toggle switch (see Picture tuning in chapter  
'Guided' adjustment mode or 'Random access' adjustment mode).  
COMM PO RT  
(800 peripherals)  
R
G
(S)  
B
B-Y  
S- VI DEO  
R EM OT  
E
RS23 2 OU T  
R
-
Y
Y(S)  
S
VID EO  
RS23 2 IN  
Professional VCR  
Audio amplifier  
(R-Y)Y(B-Y)S or(R-Y)Ys(B-Y) input selection  
a. Press digit button 5 on the RCU or  
b. With the local keypad :  
(to gain access to the local keypad, see Local keypad in chapter Location and  
functions of control.)  
- Press ADJUST key, the General access menu is displayed on the screen.  
R5975238 BARCOVISION 701 MULTIMEDIA 280497  
4-8  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CONNECTIONS  
- Use the control disk to high-  
light 5.  
G E NE R A L A C CE S S  
SH AR PN ES S  
- Press ENTER to select the  
highlighted source.  
TI N T  
C O L O R  
BR IG HTNE SS  
C O N TR A S T  
5
3
1
6
4
2
Enter ADJUST  
Select with  
,
or  
t he n <E N TE R> .  
<EXIT> t o return  
Connecting a Component source with Tri-level sync.  
(R-Y)Y(B-Y) analog input terminals with Tri-level sync input or with Tri-level sync  
on the luminance input.  
COMM PORT  
(800 peripherals)  
R
G
(S)  
B
B-  
S- VID EO  
REMO TE  
S
VI DEO  
RS2 32  
O
UT  
R
-
Y
Y(S)  
Y
RS232 IN  
Professional VCR  
with Tri-level sync  
Audio amplifier  
R5975238 BARCOVISION 701 MULTIMEDIA 280497  
4-9  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CONNECTIONS  
(R-Y)Y(B-Y)3S or (R-Y)Y3s(B-Y) input selection  
a. Press digit button 6 on the RCU or  
b. With the local keypad :  
(to gain access to the local keypad, see Local keypad in chapter Location and  
functions of control.)  
- Press ADJUST key, the General access menu is displayed on the screen.  
- Use the control disk to high-  
light 6.  
G E NE R A L A C CE S S  
- Press ENTER to select the  
highlighted source.  
SH AR PN ES S  
TI N T  
C O L O R  
BR IG HTNE SS  
C O N TR A S T  
5
3
1
6
4
2
Enter ADJUST  
Select with  
,
or  
t he n <E N TE R> .  
<EXIT> t o return  
R5975238 BARCOVISION 701 MULTIMEDIA 280497  
4-10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CONNECTIONS  
Connecting a computer, e.g. IBM PC (or compatible), Apple  
Macintosh to the RS232 input of the projector.  
The projector has a RS232 port that allows it to communicate with a computer.  
Applications: remote control and data communications.  
a) remote control:  
- easy adjustment of the projector via IBM PC (or compatible) or MAC connection.  
- allow storage of multiple projector configurations and set ups.  
- wide range of control possibilities.  
- address range from 0 to 255.  
b) data communications:  
- sending data to the projector or copying the data from the projector to a hard  
memory device.  
COMM PO RT  
(800 peripherals)  
R
G
(S)  
B
B-  
S- VI DEO  
R EM OT  
E
S
VID EO  
RS23 2 IN  
RS23 2 OU T  
R
-
Y
Y(S)  
Y
RS232  
connection  
R5975238 BARCOVISION 701 MULTIMEDIA 280497  
4-11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CONNECTIONS  
PERIPHERAL EQUIPMENT  
Connecting a RCVDS 05 switcher to the projector.  
-Upto10inputs(20inputs whenvideoandS-video)withtheRCVDS05switcherand  
up to 90 inputs when 10 RCVDS switchers are linked via the expansion modules.  
- Serial communication with the projector.  
-RemotecontrolbuttonsontheRCVDStocontroltheprojector(sourceselectionand  
analogsettings)  
- The selected source number will be displayed on a 2 digit display and the selected  
input modules will be indicated with a LED on the rear.  
For more information about the use of the RCVDS 05, consult the Owner's Manual,  
ordernumber:R5975765.  
Connecting a VS05 switcher to the projector.  
TheVS05canswitchupto5CompositeVideosources,3S-VideoSourcesand1RGB  
analogorcomponentVideosourcetotheprojector. Inaddition,theaudiosignalproper  
to the source, can be switched to an audio amplifier.  
Order number : R9827890.  
For more information about the use of the VS05, consult the Owner's Manual, order  
number:R5975245.  
Connecting an IR Remote Receiver to the projector  
Thisinfra-redreceiverunitmakesitpossibletocontroltheprojectorfromanotherroom.  
There is a communication line cable between the IR receiver and the projector or the  
RCVDS. The infrared control information from the Remote Control Unit is sent to the  
IR Remote Receiver. The IR Remote Receiver 800 displays the selected source on  
a 7-segment display.  
Order number : R9827515.  
R5975238 BARCOVISION 701 MULTIMEDIA 280497  
4-12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CONTROLLING  
CONTROLLING  
Battery installation in the RCU  
How to use the RCU  
Projectoraddress  
How to display a projector address  
How to program an address into the RCU  
Inputselection  
Picturecontrols  
The Pause key  
R5975238BARCOVISION701MULTIMEDIA070497  
5-1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CONTROLLING  
Battery installation in the RCU.  
A new battery (not yet installed to save the battery life  
time) is delivered inside the plastic bag with the power  
cord. Before using the RCU, start first the battery  
installation procedure.  
Remove the battery cover on the backside of the  
remote control by pushing the indicated handle a little  
to the bottom of the RCU. Lift up the top side of the  
cover at the same time (fig. 1).  
Insert the new 9 V battery (E-block type, e.g. 6F22S or  
equivalent) in the lower compartment and connect the  
battery to the contact plate.  
Insert the battery into the lower compartment and put  
the cover back.  
fig.1  
Insert here,  
behind the  
plastic cover, the  
'Insert card for  
RCU'. You can  
cut out the  
correct insert  
card on one of  
the last pages of  
this manual.  
Contact  
plate  
Battery  
fig.2  
310a.DRW  
5-2  
R5975238BARCOVISION701MULTIMEDIA070497  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CONTROLLING  
The BARCOVISION 701 MULTIMEDIA can be controlled with  
a. the RCU  
b. the hardwired RCU (cable not included)  
c. the local keypad.  
Controlling the projector with the RCU and the hardwired RCU is the same.  
How to use the RCU  
a) Point the front of the RCU towards the reflective screen surface  
Ceiling  
IR sensor  
Scr een  
R C U 7 0 0  
b) Point the front of the RCU towards one of the IR sensors in the projector.  
When using the wireless remote control, make sure you are within the effective  
operating distance (30m, 100ft in a straight line). The remote control unit will not  
function properly if strong light strikes the sensor window or if there are obstacles  
between the remote control unit and the projector's IR sensor.  
R5975238BARCOVISION701MULTIMEDIA070497  
5-3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CONTROLLING  
Rear side of projector  
Front of projector  
45°  
45°  
45°  
45°  
E
N
T
ER  
E
F
N
T
E
E
R
Z
FR E  
E Z  
R
E
0
0
R C U  
9
7
9
7
8
6
8
5
3
5
3
6
4
2
4
2
1
1
c) RCU used in a hardwired configuration.  
C
(8  
OM  
M
P
O
h
R
e
T
ra  
R
S
2
3
2
I
N
R
S
2
3
2
OU  
T
I
R
S
-V  
I
D
E
O
R
E
M
O
T
E
R
G
(
S
)
B
S
V
I
D
E
O
0
0
p
e
ri  
p
l
s
)
219  
Plug one end of the remote cable in the connector on the bottom of the RCU and the  
second side in the connector in the rear panel of the BARCOVISION 701 MULTIME-  
DIA labelled 'REMOTE'.  
5-4  
R5975238BARCOVISION701MULTIMEDIA070497  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CONTROLLING  
Projectoraddress  
a. hardware set up of the projector address.  
Every projector requires an individual address between 0 and 16 which is set with  
hardware DIP switches inside the projector. To change that address, contact a  
BARCO authorized technician.  
b. How to control the projector.  
The projector's address may be set to any value between 0 and 16. When the address  
is set, the projector can be controlled now with :  
- the RCU for addresses between 0 and 9.  
- computer, e.g. IBM PC (or compatible), Apple MAC, etc. for addresses between  
0 and 16 (only when the optional RS232 communication port is installed)  
Note : a projector will respond to an RCU set to an address of '0' regardless of what  
address is set in the projector itself.  
c. Using the RCU.  
Before using the RCU, it is necessary to enter the projector address into the RCU  
(only when that address is between 1 and 9). The projector with the corresponding  
address will listen to that specific RCU.  
When address 0, 'zero address' is programmed into the RCU, every projector, without  
exception will listen to the commands given by this RCU.  
How to display a projector address?  
Press the ADDRESS key (re-  
cessed key on the RCU) with a  
pencil.  
The projector's address will be dis-  
played in a 'Text box'. This text box  
disappears after a few seconds.  
To continue using your RCU, it is  
necessary to enter an address with  
the digit buttons (address between  
0 and 9). For example : if the  
Address key displays projector  
address 003, the press "3" digit  
PROJECTOR  
ADDRESS  
001  
button on the RCU to set the RCU's  
address to match the projector's  
address. Do not press digit 003.  
This will address the remote to '0'  
and control all projectors in the  
room.  
R5975238BARCOVISION701MULTIMEDIA070497  
5-5  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CONTROLLING  
How to program an address into the RCU?  
Press the ADDRESS key (recessed key on the RCU) with a pencil and enter the  
address with the digit buttons. That address can be any digit between 0 and 9.  
When programming '0', zero address, the RCU will control a projector regardless of  
the projector's address. This feature allows multiple projectors with different  
addresses to be controlled by a single RCU.  
Inputselection  
Source No Projectorinput  
Pressdigitbutton  
1
2
3
4
5
Comp. Video  
S-Video  
1
2
3
4
RGBS or RGsB  
RGB3S or RG3sB  
(R-Y)Y(B-Y)S or  
(R-Y)Ys(B-Y)  
5
6
6
(R-Y)Y(B-Y)3Sor  
(R-Y)Y3s(B-Y)  
Two possible ways of selecting an input :  
a) With the digit buttons on the RCU, it is possible to select one of the four input  
sources, Video, S-Video, RGsB or RGBS, RG3sB or RGB3S, (R-Y)Ys(B-Y) or  
(R-Y)Y(B-Y)S, (R-Y)Y3s(B-Y) or (R-Y)Y(B-Y)3S.  
b) With the local keypad :  
press first the ADJUST key to display the  
General access menu.  
ADJUST  
EXI T  
STANDBY  
ENTER  
5-6  
R5975238BARCOVISION701MULTIMEDIA070497  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CONTROLLING  
Use the control disk to highlight the  
desired source number. Push the  
control disk up or down to move the  
cursor up and down, push the con-  
trol disk to the left or to the right to  
move the cursor to the left and to  
the right.  
G E N E R A L A C C E S S  
S H A RP N E S S  
TI N T  
C O L O R  
B R IG H TNE S S  
C O N TR A S T  
5
3
1
6
4
2
En ter ADJU ST  
Select with  
Press ENTER to confirm your se-  
lection.  
,
or  
t he n < E NTE R> .  
<EXI T> to re turn  
When a valid and available source  
is selected, there will be informa-  
tion displayed on the screen about  
that source. This information in-  
cludes :  
- Source number  
- Horizontal frequency  
- Vertical frequency  
Source  
2
Fh= 15.6 kHz  
Fv= 50 Hz  
When the entry is a non valid  
sourcenumber,awarningappears  
on the screen : 'input not avail-  
able'.  
WA RN IN G  
input not  
available  
R5975238BARCOVISION701MULTIMEDIA070497  
5-7  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CONTROLLING  
When a valid source number is  
selected, the projector will display  
this source or it will wait on the  
selected source number until the  
sourcebecomesavailable. Ames-  
sage 'source not available' will be  
displayed for a short time.  
W A RNI NG  
source not  
available  
Picturecontrols  
The picture controls can be adjusted with :  
a) The RCU. The control keys are located on the left side of the key panel of the RCU  
and indicated with the name of the control and an icon.  
When an image control is pressed, a text box with bar scale and the function  
name of the control, e.g. 'brightness...' appears on the screen (only if text is ON).  
The length of the bar scale indicates the current memorized setting for this  
source. The bar scale changes as the + or - buttons of the control are pressed.  
b) The local keypad  
All controls are hidden in the General access menu.  
- Press ADJUST to display the  
General access menu.  
- Use the control disk to highlight  
the desired analog control and  
ADJUST  
EXIT  
press ENTER to select.  
STANDBY  
ENTER  
5-8  
R5975238BARCOVISION701MULTIMEDIA070497  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CONTROLLING  
G E N E R A L A C C E S S  
S H A RP N E S S  
TI N T  
C O L O R  
B R IG H TNE S S  
C O N TR A S T  
5
3
1
6
4
2
En ter ADJU ST  
Select with  
,
or  
t he n <E N TE R> .  
<EXIT> t o return  
When a picture control is selected, a text box with bar scale and the function name  
of the control appear on the screen. The length of the bar scale indicates the current  
memorized setting for this source (percentage scale). The bar scale changes as the  
control disk is pushed to the left or to the right.  
Brightness Control  
A correct 'brightness' setting is im-  
portant for good image reproduc-  
tion. Adjust the brightness with the  
+ button and - button (RCU) or  
pushing the control disk to the left  
or to the right (local keypad) until  
the darkest parts of the picture ap-  
pear black.  
A bar scale gives a visual indica-  
tion on the screen of the current  
brightness setting while pressing  
BRI G HT NESS  
on the above indicated buttons. If  
3 5  
the bar scale is not visible on the  
18 9  
screen, press 'TEXT' once and re-  
try the above indicated buttons.  
The bar scale increases when  
pressing on the + button (higher  
brightness) and decreases when  
pressing on the - button (lower  
brightness).  
R5975238BARCOVISION701MULTIMEDIA070497  
5-9  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CONTROLLING  
Contrast Control  
A correct 'contrast' setting is impor-  
tant for good image reproduction.  
Adjust the contrast to the level you  
prefer, according to room lighting  
conditions.  
A bar scale gives a visual indication  
on the screen of the current con-  
trast setting while pressing the + or  
- buttons (RCU) or pushing the con-  
trol disk to the left or to the right  
(local keypad). If the bar scale is  
not visible on the screen, press  
'TEXT'keyonceandretrytheabove  
indicated buttons.  
CO NT RAST  
7 0  
The bar scale increases when  
pressing on the + button (higher  
contrast) and decreases when  
pressing on the - button (lower con-  
trast).  
Color Saturation Control  
Color saturation is only active for  
Video and S-Video. Adjust the  
color intensity of the picture. Ad-  
just the color saturation using the +  
and - buttons (RCU) or pushing  
the control disk to the left or to the  
right (local keypad). A bar scale  
gives a visual indication on the  
screen of the current color setting  
while pressing on the above indi-  
cated buttons. If the bar scale is  
not visible on the screen, press  
'TEXT' key once and retry the  
above indicated buttons. The bar  
scale increases when pressing on  
the + button (richer colors) and  
decreases when pressing the -  
button (lighter colors).  
C O L O R  
7 0  
5-10  
R5975238BARCOVISION701MULTIMEDIA070497  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CONTROLLING  
Tint Control  
Tint is only active for Video and S-  
Video. Tint control is effective  
only when using the NTSC 4.43 or  
NTSC 3.58 system. A bar scale  
gives a visual indication on the  
screen of the current tint setting  
while pressing the + or - buttons  
(RCU) or pushing the control disk  
to the left or to the right (local  
keypad). If the bar scale is not  
visible on the screen, press the  
'TEXT' key once and retry the  
above indicated buttons.  
TI NT  
7 0  
The bar scale increases when  
pressing on the + button and de-  
creases when pressing the - but-  
ton.  
Sharpness Control.  
Sharpness control only active for  
Video and S-Video. A bar scale  
gives a visual indication on the  
screen of the current sharpness  
setting while pressing the + or -  
buttons (RCU) orpushing the con-  
trol disk to the left or to the right  
(local keypad). If the bar scale is  
not visible on the screen, press  
'TEXT' key once and retry the  
above indicated buttons.  
SHARPNESS  
The bar scale increases when  
pressing on the + button (sharper  
picture) and decreases when  
pressing on the - button (softer  
picture).  
3
dB  
The Pause key.  
When the Pause key is pressed, the image projection is stopped but the projector  
remains with full power for immediate restart.  
To restart the image :  
- Press the Pause key,  
- Select a source number.  
R5975238BARCOVISION701MULTIMEDIA070497  
5-11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CONTROLLING  
5-12  
R5975238BARCOVISION701MULTIMEDIA070497  
Download from Www.Somanuals.com. All Manuals Search And Download.  
START UP OF THE ADJUSTMENT MODE  
START UP OF THE ADJUSTMENT MODE  
R5975238 BARCOVISION 701 MULTIMEDIA 070497  
6-1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
START UP OF THE ADJUSTMENT MODE  
Entering the adjustment mode  
ADJUSTMENT MODE  
Select  
be lo w:  
a
path from  
G U I D E D  
R A N D O M A C C E S S  
I NS TAL LA TIO N  
S E RV I C E  
I RI S  
so urce  
1
Select with  
or  
th en <E NTER >  
<EXIT> to return  
IRIS  
Installation  
(only for qualified  
technician)  
Service  
Random Access  
Adjustment  
Guided  
Adjustment  
6-2  
R5975238 BARCOVISION 701 MULTIMEDIA 070497  
Download from Www.Somanuals.com. All Manuals Search And Download.  
START UP OF THE ADJUSTMENT MODE  
Adjustment mode  
All picture geometry and convergence adjustments are made while in the  
'Adjustment mode'. Two possible ways to enter the adjustment mode :  
a) Using the RCU.  
Press the ADJUST key.  
The projector displays the path selection menu.  
b) Using the local keypad.  
AD JU ST  
EXIT  
Press the ADJUST key.  
The projector displays the General  
access menu.  
STA N DB Y  
EN T ER  
Use the control disk to high-  
light enter ADJUST and press  
ENTER. The path selection  
menu will be displayed.  
GENERAL ACCESS  
S H A RP N E S S  
TI N T  
C O L O R  
B R IG H TNE S S  
C O N TR A S T  
5
3
1
6
4
2
En ter ADJU ST  
Select with  
,
or  
then <ENTER>.  
<EXIT> to return  
R5975238 BARCOVISION 701 MULTIMEDIA 070497  
6-3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
START UP OF THE ADJUSTMENT MODE  
Note : to adjust the Analog picture control while in the 'Adjustment mode', press  
the ADJUST key. The next General Access menu will be displayed.  
Push the control disk up or  
down to select the analog con-  
trol to be adjusted and press  
G E N E R A L A C C E S S  
S HA RP N ES S  
TI N T  
the ENTER key to confirm.  
C O L O R  
B RI GH TN ES S  
C O N TR A S T  
When the analog control is  
adjusted the projector returns  
automatically to the General  
quit ADJUST  
access menu. When you want  
Select with  
,
to return to the Adjustment  
mode, press EXIT, otherwise  
select quit ADJUST and press  
ENTER to return to operational  
mode.  
or  
t he n < E NTE R> .  
<EXI T> to re turn  
64 3  
You are now in the 'Adjustment mode'. The control disk is used to make menu  
selections and also vertical and horizontal adjustments. The ENTER and EXIT  
keys are used to move forward and backward through the menu structure. The  
ADJUST key can be used to terminate the adjustment mode while a path  
selection menu (head menu) is displayed.  
There are 5 possible paths to follow once in the Adjustment mode. They are :  
INSTALLATION - Installation  
should be selected if the pro-  
jector has been relocated and/  
ADJUSTMENT MODE  
Select  
be lo w:  
a
path from  
or a different screen size is  
desired.  
G U I D E D  
R A N D O M A C C E S S  
I NS TA LL A TIO N  
S E R V I C E  
When selecting 'Installation',  
the user or operator will be  
warned to call a qualified tech-  
nician to perform the installa-  
tion procedure (see example  
of projected warning on next  
page).  
I RI S  
so urce  
1
Select with  
th en < EN TE R>  
<EXIT> to return  
or  
GUIDED - Guided should be selected if the user intends to perform a complete  
alignment of the projected image. All of the necessary geometry and conver-  
gence adjustments are made in a predetermined sequence.  
RANDOM ACCESS - Random Access should be selected if the user intends to  
make only a few adjustments.  
SERVICE-Serviceshouldbeselectediftheuserintendstodeleteblocks,change  
password or apply information.  
IRIS - This selection will only be available when the autoconvergence unit IRIS  
is connected to the projector.  
6-4  
R5975238 BARCOVISION 701 MULTIMEDIA 070497  
Download from Www.Somanuals.com. All Manuals Search And Download.  
START UP OF THE ADJUSTMENT MODE  
While in Guided or Random Access adjustment Mode, the user may use an  
external source, an internally generated genlocked pattern or an internally  
generated multifrequency cross hatch pattern as a setup pattern.  
Warning during the start up of  
the installation mode.  
WARNING  
RISK OF ELECTRICAL SHOCK  
NO USER ADJUSTABLE PARTS  
INSIDE  
THE FO LL O WI NG  
I NS TA LL ATIO N ME NU S  
AR E R ESER VED TO ,  
A ND TO BE P ER FO RM ED O NL Y  
BY BA RCO PER SON NEL , O R  
B AR CO A UTHO RI ZE D DE AL ER S  
IF QUALIFI ED, PRESS  
<E NTER > TO CO NTIN UE , OR  
IF N OT, <E XIT> TO RETU RN.  
Some items in the Adjustment mode are password protected. While selecting  
such an item, the projector asks you to enter your password. (Password  
protection is only available when the password DIP switch on the controller  
module is in the ON position. Contact a BARCO authorized technician when no  
password is requested during the adjustment procedure and password protec-  
tion is desired.)  
Your password contains 4 dig-  
its.  
a) Adjusting the projector with  
the RCU.  
Enter the digits with the numeric  
keys on the RCU.  
Example : 2 3 1 9  
enter  
password  
xxxx  
For each digit entered, a 'X' ap-  
19 7  
pears on the screen under the  
displayed text 'enter password'.  
When your password is correct,  
you get access to the 'Adjust-  
ment mode'.  
When the entered password is  
wrong, The message 'Wrong  
password !!!' will be displayed.  
The projector stays on the pre-  
vious selected item.  
W RO NG  
PASSWORD  
Factory programmed  
!!!  
password : 0000  
1 9 8  
R5975238 BARCOVISION 701 MULTIMEDIA 070497  
6-5  
Download from Www.Somanuals.com. All Manuals Search And Download.  
START UP OF THE ADJUSTMENT MODE  
b) adjusting the projector with the local keypad.  
When the 'compose password'  
menu is displayed, select with con-  
trol disk the first digit of your pass-  
word and press ENTER. Continue  
by selecting the second digit with  
the control disk and press ENTER.  
Handle in the same way for the  
third and fourth digit.  
C O M P O S E  
P A S S W O R D  
? ? ?  
7
4
1
8
5
2
0
9
6
3
Select with  
,
or  
t hen <ENTE R>  
< EXIT> to r et ur n  
When your password is correct,  
you get access to the 'Adjustment  
mode'.  
When the entered password is  
wrong, the message 'Wrong pass-  
word' will be displayed.  
Once the password is correctly entered, all other password protected items are  
accessible without re-entering your password.  
When re-entering the adjustment mode, it will be necessary to enter your  
password again when selecting a password protected item.  
6-6  
R5975238 BARCOVISION 701 MULTIMEDIA 070497  
Download from Www.Somanuals.com. All Manuals Search And Download.  
GUIDED ADJUSTMENT MODE  
GUIDED ADJUSTMENT MODE  
7-1  
R5975238 BARCOVISION 701 MULTIMEDIA 070497  
Download from Www.Somanuals.com. All Manuals Search And Download.  
GUIDED ADJUSTMENT MODE  
Start up of the guided adjustment mode.  
Push the control disk up or  
down to highlight GUIDED on  
the 'Adjustment mode' menu  
and then press ENTER.  
ADJUSTMENT MODE  
Select  
be lo w:  
a
path from  
G U I D E D  
R A N D O M A C C E S S  
I NS TA LL A TIO N  
S E R V I C E  
The Guided Adjustment mode  
is password protected (when  
the password function is ac-  
tive). Enter your password to  
continue(seealsochapterStart  
up of the adjustment mode)  
I RI S  
so urce  
1
Select with  
or  
th en < EN TE R>  
<EXIT> to return  
ENTER continues to the password menu  
and then to Setup Pattern Selection  
EXIT returns to operational mode.  
7-2  
R5975238 BARCOVISION 701 MULTIMEDIA 070497  
Download from Www.Somanuals.com. All Manuals Search And Download.  
GUIDED ADJUSTMENT MODE  
Overview flowchart 'Guided Adjustment' procedure.  
G U I D E D A D J US TM E N T M O D E  
INS U RE T HA T  
T HE P RO JE CT O R HA S BE EN  
INS TA LL ED C OR RE CT LY ,  
AN D TH AT T HE L EN SE S/CR TS  
Picture tuning  
H AV E BE EN PR OP ER LY  
F OC US ED AN D A LIGN ED .  
AL L AD JU ST ME NT S AR E  
M AD E WITH TH E A RR O W K EY S  
<ENTE R> to con tinue  
<EXIT> to return  
Horizontal & vertical  
shift  
Left - right corrections  
Top - bottom correc-  
tions  
Size - linearity adjust-  
ment  
Convergence  
Blanking  
Color Balance  
7-3  
R5975238 BARCOVISION 701 MULTIMEDIA 070497  
Download from Www.Somanuals.com. All Manuals Search And Download.  
GUIDED ADJUSTMENT MODE  
Selecting Setup Pattern  
If an external source is con-  
nected to the projector, the  
Setup pattern menu will be dis-  
played. Push the control disk  
up or down to highlight the  
desired setup pattern and then  
press ENTER.  
C h o o s e  
a
setup pattern  
fro m bel ow:  
S E L E C TED S O U R C E  
G E N L O C K E D P A TTE R N  
I NTE RN A L  
#
P ATTER N  
so urce  
1
Genlocked pattern : internally  
generated cross hatch pattern,  
locked on the external source.  
Select with  
th en < EN TE R>  
<EXIT> to return  
or  
Internal # pattern : internally  
generated cross hatch pattern  
and locked on internal gener-  
ated sync signals. (No external  
source necessary)  
ENTER continues to Guided Adjustment  
Mode or Internal # Pattern Selection  
EXIT returns to Path Selection  
ADJUST returns to operational mode  
If no external source is con-  
nected to the projector, the in-  
ternalcrosshatchpatternmenu  
will be displayed.  
The menus in this manual are  
created for an external source,  
connected to one of the inputs,  
and the 'Genlocked pattern' is  
selected.  
7-4  
R5975238 BARCOVISION 701 MULTIMEDIA 070497  
Download from Www.Somanuals.com. All Manuals Search And Download.  
GUIDED ADJUSTMENT MODE  
Internal Cross Hatch Pattern  
The Internal # pattern menu  
will be displayed if the internal  
cross hatch pattern has been  
selected or if no source is con-  
nected to the projector.  
INTERNAL  
#
PATTERN  
kHz  
/
Hz  
15.6/50  
15.7/60  
31.2/50  
31.5/60  
31.2/5 0  
31.5/60  
33.7/60  
PAL/SECAM  
NTSC  
EDTV  
IDTV  
The table below lists the fac-  
tory preset frequencies avail-  
able.  
HDTV EUREKA  
HDTV ATV  
HDTV HI-VISION  
Select with  
or  
<ENTE R> to ac cept  
<EXIT> to return  
Push the control disk up or  
down to highlight the desired  
crosshatchfrequencyandthen  
press ENTER.  
ENTER continues to Guided Adjustment  
Mode.  
kHz/Hz  
EXIT returns to Setup Pattern Selection.  
15.6/50  
15.7/60  
31.2/50  
31.5/60  
31.2/50  
31.5/60  
33.7/60  
15.8/60  
21.8/60  
31.5/70  
35.5/87  
PAL/SECAM  
NTSC  
EDTV  
48.5/60  
44.2/70  
61.0/76  
22.2/60  
SUPER VGA 1  
SUPER VGA 2  
SUPER VGA 3  
MAC CLASSIC  
IDTV  
HDTV EUREKA  
HDTV ATV  
HDTV HI-VISION  
EGA 1  
EGA 2  
VGA 1,2  
VGA 4  
Note: Before continuing, in-  
sure that the lenses are prop-  
erly focused and that the CRT  
projectionangleiscorrectlyad-  
justed. If any misalignment is  
noticed, consult a qualified  
service technician.  
GUIDED ADJUSTMENT MODE  
I NS UR E THA T  
TH E PR OJ EC TOR H AS B EE N  
I NS TA LL ED C OR RE CTLY ,  
AN D TH AT TH E LE NSE S/ CR TS  
HA VE B EE N P RO PE RL Y  
FO CU SE D AN D AL IG NE D.  
AL L AD JU STME NTS AR E  
M AD E WI TH THE A RR OW K EY S  
<ENTER> to continue  
<EXIT> to return  
ENTER continues with the Picture Tuning  
EXIT returns to Setup Pattern Selection or  
Internal # Pattern Selection  
ADJUST returns to operational mode  
7-5  
R5975238 BARCOVISION 701 MULTIMEDIA 070497  
Download from Www.Somanuals.com. All Manuals Search And Download.  
GUIDED ADJUSTMENT MODE  
Picturetuning  
Depending on the source type (video, S-Video, RGB(S) analog with composite  
or Tri-level sync, component input with composite or Tri-level sync) the picture  
tuning menu offers the possibility to toggle :  
For Video, S-Video or Component video sources :  
- The Synchronisation speed  
- The Line Doubler feature (option)  
For RGB analog or component input with composite or tri-level sync sources:  
- Synchronisation speed  
- Enhanced blue on or off  
SyncFast/Slowtoggle  
Highlight Sync by pushing the  
control disk up or down and  
press ENTER to toggle be-  
tween FAST and SLOW  
PICTURE TUNING  
Note : SYNC is normally used  
in the SLOW position. The  
FAST position is used to com-  
pensate for unsteady sync  
pulses from older video play-  
back equipment.  
SY NC  
CH ROMA D EL AY  
:
FA ST  
:
P AL  
C O N TI N U E  
Select with  
<ENTER> t o accept  
<EXIT> to return  
or  
Hint : when the line doubler  
feature is ON (active), toggle  
the sync to FAST.  
ENTER toggles between SLOW and FAST.  
EXITreturnstotheGuidedAdjustmentmenu.  
LineDoubler(option)  
Line doubling is only possible for Video, S-Video or Component Video images  
on standard line frequency.  
To eliminate the video line patterns and to improve the image stability the line  
doubler has to be switched on. The line doubler is default set in the ON position  
when starting up for the first time. The setting of the line doubler will be saved  
together with the source number.  
Hint : when the line doubler feature is ON (active), toggle the sync to FAST.  
When a bad video tape has to be displayed, switch off the line doubler feature to  
obtain a stable image.  
7-6  
R5975238 BARCOVISION 701 MULTIMEDIA 070497  
Download from Www.Somanuals.com. All Manuals Search And Download.  
GUIDED ADJUSTMENT MODE  
Highlight LineDoubler by push-  
ing the control disk up or down  
and press ENTER to toggle  
between ON (active) and OFF  
(non active)  
PI CT UR E TU NI NG  
SY NC  
:
FA ST  
CH RO MA DE LA Y  
LI NE DOUB LER  
:
:
P AL  
ON  
C O N T I N U E  
Select with  
or  
<ENTER> t o accept  
<EXIT> to return  
ENTER toggles beween ON and OFF.  
EXIT returns to the Guided Adjustment Menu.  
Enhanced blue ON/OFF  
Highlight Enhanced Blue by  
pushing the control disk up or  
down and press ENTER to  
toggle between ON and OFF  
(only available when RGB  
analog signals are connected  
to the projector).  
PI CT UR E TU NI NG  
SY NC  
:
FA ST  
EN HAN CED B LUE  
:
ON  
C O N TI N U E  
When Enhanced Blue is ON,  
the blue color will be displayed  
as cyan.  
Select with  
<ENTER> t o accept  
or  
<EXIT> to return  
Note : Enhanced blue is only  
used when an RGBS or RGsB  
analog signal from a computer  
is being displayed. Enhanced  
blue is not recommended for  
non computer generated im-  
ages.  
ENTER will toggle Enhanced Blue between  
ON and OFF.  
EXIT will return to the Guided Adjustment  
menu.  
For displaying graphics, this  
Enhanced Blue function could  
falsify the color reproduction.  
In this case, put Enhanced  
Blue OFF  
7-7  
R5975238 BARCOVISION 701 MULTIMEDIA 070497  
Download from Www.Somanuals.com. All Manuals Search And Download.  
GUIDED ADJUSTMENT MODE  
RasterCenteringonGreenCRTFaceplate  
The green raster must be  
centered both horizontally and  
vertically on the center of the  
CRT surface. To center the  
greenraster,lookintothegreen  
lens and use the control to  
move the raster.  
H
AND  
V
SHIFT  
U SE THE A RR OW K EY S  
TO CE NTE R TH E R AS TE R  
ON THE FA CE PLA TE OF THE  
G RE E N C RT HO R IZO NTA LL Y  
AN D VE RTIC ALLY ,  
AN D THEN TO S HIFT  
TH E RED A ND BL UE IMAG ES  
VER TICA LLY, IN ORDE R  
TO CO NV ER GE TH E CE NTER  
OF THE P RO JEC TE D IMAG E.  
Caution  
<ENTER> to continue  
<EXIT> to return  
It is necessary to look into the  
lenses to perform these ad-  
justments. To avoid eye dis-  
comfort while looking into the  
lenses,reducethecontrastand  
gradually increase the bright-  
ness level until the raster be-  
comes visible.  
ENTER continues to Green Raster Shift  
EXIT returns to Guided Adjustment Mode  
ADJUST returns to operational mode  
Warning : In order to ensure maximum CRT longevity and to avoid  
CRT damage, do not shift the raster outside the phosphor area of the  
CRT.  
forbidden area  
projected raster  
crt faceplate border  
phosphor border  
To begin the adjustment, press the ENTER key.  
7-8  
R5975238 BARCOVISION 701 MULTIMEDIA 070497  
Download from Www.Somanuals.com. All Manuals Search And Download.  
GUIDED ADJUSTMENT MODE  
correct raster position  
wrong raster position  
After centering the green raster, press the ENTER key to continue.  
ENTER continues to Red Raster Shift  
EXIT returns to Horizontal and Vertical  
Shift  
7-9  
R5975238 BARCOVISION 701 MULTIMEDIA 070497  
Download from Www.Somanuals.com. All Manuals Search And Download.  
GUIDED ADJUSTMENT MODE  
Shifting Red and Blue on Green  
Use the control disk to shift the red image until the center coincides with the  
center of the green image.  
red or blue  
imag e  
green  
ima ge  
When the red image is correctly positioned, press the ENTER key to continue  
with the blue image.  
ENTER continues to blue raster shift  
EXIT returns to green raster shift  
Left-Right(East-West)Adjustments  
Left-right adjustments affect  
only the vertical lines of the  
LEFT-RIGHT (E/W)  
setup pattern. Only the green  
image is displayed while mak-  
ing left-right adjustments. The  
A D J U S T  
VE RTIC AL CE NTER LI NE  
B OW A ND SK EW ,  
SI DE BO W A ND KE YSTON E.  
red and blue images will auto-  
matically be corrected in the  
same manner.  
A FTER S Q UA RI NG  
THE SID ES OF THE IMA GE,  
AD JU ST THE D ES IR ED  
SCRE EN WIDTH. (H S IZE)  
Convergence corrections are  
automatically disabled for the  
duration of these adjustments.  
<ENTER> to continue  
<EXIT> to return  
Press the ENTER key to con-  
tinue.  
ENTER continues to vertical centerline bow  
adjustment  
EXIT returns to Picture Tuning  
ADJUST returns to operational mode  
7-10  
R5975238 BARCOVISION 701 MULTIMEDIA 070497  
Download from Www.Somanuals.com. All Manuals Search And Download.  
GUIDED ADJUSTMENT MODE  
VerticalCenterlineBowAdjustment  
Correct by pushing  
the control disk to  
the right  
The vertical centerline bow  
adjustment corrects for curva-  
ture in the horizontal direction  
in the middle of the picture for  
the vertical lines.  
Push the control disk to the  
left or to the right to adjust the  
vertical centerline bow of the  
setup pattern and then press  
the ENTER key to continue.  
Vertical centerline  
Correct by pushing  
the control disk to  
the left  
VerticalCenterlineSkewAdjustment  
The vertical centerline skew  
function corrects for tilting of  
the vertical lines in the middle  
of the picture.  
Correct by pushing  
the control disk to  
the right  
Push the control disk to the  
right or to the left to adjust the  
vertical centerline skew of the  
setup pattern until this line is  
straight. Misalignment of the  
outer vertical lines will be cor-  
rected with the bow and key-  
stone corrections. Press EN-  
TER to continue.  
Vertical centerline  
Correct by pushing  
the control disk to  
the left  
7-11  
R5975238 BARCOVISION 701 MULTIMEDIA 070497  
Download from Www.Somanuals.com. All Manuals Search And Download.  
GUIDED ADJUSTMENT MODE  
RightKeystoneAdjustment  
Correct by pushing  
the control disk to  
the right.  
The right keystone function  
corrects the keystone geom-  
etry distortion of the vertical  
lines on the right side of the  
image.  
Push the control disk to the  
right or to the left to adjust the  
right keystone (vertical lines)  
of the setup pattern and press  
ENTER to continue  
Correct by pushing  
the control disk to  
the left.  
LeftKeystoneAdjustment  
Correct by pushing  
the control disk to  
the right.  
Theleftkeystonefunctioncor-  
rects the keystone geometry  
distortion of the vertical lines  
on the left side of the image.  
Push the control disk to the  
right or to the left to adjust the  
left keystone (vertical lines)  
ofthesetuppatternandpress  
ENTER to continue  
Correct by pushing  
the control disk to  
the left.  
Right Bow Adjustment  
The right bow function corrects  
for curvature occurring the ver-  
tical lines at the right of the  
displayed image.  
Correct by pushing  
the control disk to  
the right.  
Push the control disk to the  
right or to the left to adjust the  
right bow of the setup pattern  
(vertical lines) and press EN-  
TER to continue.  
Correct by pushing  
the control disk to  
the left.  
7-12  
R5975238 BARCOVISION 701 MULTIMEDIA 070497  
Download from Www.Somanuals.com. All Manuals Search And Download.  
GUIDED ADJUSTMENT MODE  
Left Bow Adjustment  
The left bow function corrects  
forcurvatureoccurringthever-  
tical lines at the left of the dis-  
played image.  
Correct by pushing  
the control disk to  
the right.  
Push the control disk to the  
left or to the right to adjust the  
left bow of the setup pattern  
(vertical lines) and press EN-  
TER to continue.  
Correct by pushing  
the control disk to  
the left.  
HorizontalSizeAdjustment  
Adjust the horizontal size by  
pushing the control disk to the  
left or to the right until the cor-  
rect image width is obtained.  
Note :  
- if the internal # pattern was  
selected, this pattern re-  
mains on the screen.  
- if the genlocked pattern was  
selected,theexternalsource  
will be displayed.  
H
SIZE  
7 0  
A bar scale and a number  
indicator(between 0 and 100)  
give a visual indication of the  
horizonal size adjustment.  
7-13  
R5975238 BARCOVISION 701 MULTIMEDIA 070497  
Download from Www.Somanuals.com. All Manuals Search And Download.  
GUIDED ADJUSTMENT MODE  
H size too  
large  
Correct by pushing  
the control disk to  
the left.  
Ideal image width  
H size too  
small  
Correct by pushing  
the control disk to  
the right.  
Top-Bottom(North-South)Adjustments  
Top-Bottom adjustments affect  
only the horizontal lines of the  
setup pattern. These adjust-  
ments are performed only on  
the green image. The red and  
blue images are automatically  
corrected in the same manner.  
TOP-BOTTOM  
A DJ US T H OR IZO NTAL  
CE NTER LI NE B OW A ND S KE W,  
TOP B OW A ND KE YS TO NE ,  
B OTTOM BO W A ND KE Y STO NE .  
Convergence corrections are  
automatically disabled for the  
duration of these adjustments.  
<ENTER> to continue  
<EXIT> to return  
Press the ENTER key to con-  
tinue.  
7-14  
R5975238 BARCOVISION 701 MULTIMEDIA 070497  
Download from Www.Somanuals.com. All Manuals Search And Download.  
GUIDED ADJUSTMENT MODE  
HorizontalCenterlineSkewAdjustment  
The horizontal skew function  
corrects for tilting of the hori-  
zontal lines in the middle of the  
picture.  
Correct by pushing  
the control disk up  
Push the control disk up or  
down to adjust the horizontal  
centerline skew of the setup  
Hor. centerline  
pattern.  
A bar scale and a numeric  
indicator (between 0 and 100)  
will give a visual indication of  
the skew correction.  
Correct by pushing  
the control disk  
down.  
HorizontalCenterlineBowAdjustment  
The horizontal centerline bow  
function corrects for curvature  
of the horizonal lines in the  
vertical direction in the middle  
of the picture.  
Correct by pushing  
the control disk  
down.  
Push the control disk up or  
down to adjust the horizontal  
centerline bow of the setup  
pattern.  
A bar scale and a numeric indi-  
cator (between 0 and 100 ) will  
give a visual indication of the  
bow correction.  
Hor. centerline  
Correct by pushing  
the control disk up.  
TopKeystoneAdjustment  
The top keystone function cor-  
rects for keystone geometry  
distortion ofthehorizontallines  
in the upper part of the picture.  
Adjust the horizontal lines in  
the upper part of the picture  
with the control disk until these  
lines are straight. Press EN-  
TER to continue.  
Correct by pushing  
the control disk  
down.  
A bar scale and a number indi-  
cator (between 0 and 100 ) will  
give a visual indication of the  
keystone correction.  
Correct by pushing  
the control disk up.  
7-15  
R5975238 BARCOVISION 701 MULTIMEDIA 070497  
Download from Www.Somanuals.com. All Manuals Search And Download.  
GUIDED ADJUSTMENT MODE  
Top Bow Adjustment  
Correct by pushing  
the control disk up.  
The top bow function corrects  
for curvature occurring in the  
upper part of the image.  
Adjust the bow of the horizon-  
tal lines in the upper side of the  
image by pushing the control  
disk up or down until these  
lines are straight.  
A bar scale and a number indi-  
cator below indicate the  
amount of adjustment.  
Correct by pushing  
the control disk  
down.  
BottomKeystoneAdjustment  
Correct by pushing  
the control disk up.  
The bottom keystone function  
corrects for keystone geometry  
distortion of the horizontal lines  
in the lower part of the image.  
Adjust the horizontal lines in  
the lower part of the image by  
pushing the control disk up or  
down until these lines are  
straight.  
A bar scale and a number indi-  
cator (between 0 and 100) will  
give a visual indication of the  
adjustment.  
Correct by pushing  
the control disk  
down.  
BottomBowAdjustment  
Correct by pushing  
the control disk up.  
The bottom bow function cor-  
rects for curvature occurring  
in the lower part of the image.  
Push the control disk up or  
down to adjust the bottom bow  
in the lower part of the setup  
pattern. Adjust until the hori-  
zontal lines are straight.  
Correct by pushing  
the control disk  
down.  
A bar scale and a number  
indicator (between 0 and 100  
%) give a visual indication of  
the adjustment.  
7-16  
R5975238 BARCOVISION 701 MULTIMEDIA 070497  
Download from Www.Somanuals.com. All Manuals Search And Download.  
GUIDED ADJUSTMENT MODE  
Size-linearityAdjustment  
Size adjustments affect the  
height and width of the pro-  
jected image. The vertical lin-  
earity adjustment is used to  
adjust the horizontal lines of  
thesetuppatternuntilthespac-  
ing between them is even. The  
horizontal phase adjustment is  
used to shift the image hori-  
zontally across the raster.  
SIZE-LINEARITY  
AD JUST VER TICA L SI ZE  
AND LINEA RITY, IN OR DER  
TO ADJ UST THE DE SIRE D  
IM AGE D IME NSI ON S.  
US E TH E  
H
PHA SE C ON TR OL  
TO SHI FT THE IMAG E  
WI TH R ES PE CT TO  
TH E RA STER .  
<ENTER> to continue  
<EXIT> to return  
VerticalLinearityAdjustment  
Correct by pushing  
the control disk up.  
Adjust the vertical linearity with  
the control disk until the dis-  
tance between the horizontal  
lines of the set up pattern are  
equal.  
Correct by pushing  
the control disk  
down  
7-17  
R5975238 BARCOVISION 701 MULTIMEDIA 070497  
Download from Www.Somanuals.com. All Manuals Search And Download.  
GUIDED ADJUSTMENT MODE  
VerticalSizeAdjustment  
Adjusttheverticalsizebypush-  
ing the control disk up or down  
until the exact image height is  
obtained.  
Note :  
- if the internal # pattern was  
selected, this pattern re-  
mains on the screen.  
- if the genlocked pattern was  
selected, the external  
source will be displayed.  
V
SIZE  
7 0  
Hint :  
In order to avoid loss of resolu-  
tion in the projected image and  
to ensure maximum CRT lon-  
gevity, do not use an  
exessively small vertical size  
setting.  
A bar scale and a number indi-  
cator (between 0 and 100 )  
give a visual indication of the  
vertical size adjustment.  
Correct by pushing  
the control disk  
down.  
Correct by pushing  
the control disk up.  
7-18  
R5975238 BARCOVISION 701 MULTIMEDIA 070497  
Download from Www.Somanuals.com. All Manuals Search And Download.  
GUIDED ADJUSTMENT MODE  
HorizontalPhaseAdjustment  
Note : No horizontal phase  
adjustment is available on the  
internal # pattern.  
For external sources :  
If the raster shift is correctly  
adjusted, the text box H phase  
is projected in the middle of  
the raster. At that moment,  
the >< indicates the middle of  
the raster.  
> <  
PHASE  
H
Adjust the hor phase control  
until the middle of the pro-  
jected image is equal with the  
middle of >< .  
7 0  
Note :  
-ifthegenlockedpatternwas  
selected, the external  
source will be displayed.  
A bar scale and a number in-  
dicator (between 0 and 100)  
on the screen give a visual  
indication of the horizontal  
phase adjustment.  
Correct by pushing  
the control disk to  
the right.  
><  
H
PHASE  
70  
Correct by pushing  
the control disk to  
the left.  
><  
H
PHASE  
70  
7-19  
R5975238 BARCOVISION 701 MULTIMEDIA 070497  
Download from Www.Somanuals.com. All Manuals Search And Download.  
GUIDED ADJUSTMENT MODE  
ConvergenceAdjustment  
Convergence adjustments af-  
fect both the horizontal and  
vertical lines of the setup pat-  
tern. These adjustments are  
performed on the red image  
while superimposed on the  
green image and then on the  
blue image while superim-  
posed on the green image.  
CONVERGENCE  
STAR T WITH GR EEN O NL Y,  
TH EN R ED O N GR EE N,  
TH EN B LU E O N GR EE N.  
US E THE A RRO W KE YS FO R  
HO RI ZON TA L A ND VE RTI CA L  
AD JU STMEN TS IN THE AR EA  
IND ICATE D BY THE B OX.  
<E NTER > WI LL M OV E  
TH E B OX TO TH E N EXT AR EA  
TO B E C ON VER GE D, AN D  
<EX IT> WI LL MOV E IT B ACK  
TO THE PR EVI OU S.  
The screen area is divided into  
25 areas. Within each area it is  
possible to move the horizon-  
tal and vertical lines of the red  
and blue picture until they co-  
incide with the green lines.  
<ENTER> to continue  
<EXIT> to return  
1 5  
1 4  
1 7  
1 6  
2 5  
2 4  
2 3  
2 2  
9
8
Use the control disk to make  
horizontal and vertical conver-  
gence adjustments in the area  
indicated by the box. Pressing  
ENTER will move the box to  
the next area of the setup pat-  
tern to be converged. Press-  
ingEXITwillmovetheboxback  
to the last area.  
5
4
1
2
3
2 0  
2 1  
1 8  
1 9  
6
7
1 2  
1 3  
1 0  
1 1  
3 9 7  
The ‘guided adjustment’ program will start with the convergence adjustment of  
the red picture on the green and continues with the blue image on the green  
image.  
Attention : when green convergence adjustments are available (option). The  
control software starts with these green corrections (the menu will indicate it also).  
Adjust until the vertical and horizontal lines are straight.  
gr een image  
red image  
CONVERGE  
ADJUSTMENT  
7 0  
7-20  
R5975238 BARCOVISION 701 MULTIMEDIA 070497  
Download from Www.Somanuals.com. All Manuals Search And Download.  
GUIDED ADJUSTMENT MODE  
BlankingAdjustment  
Blanking adjustments affect  
only the edges of the projected  
image and are used to frame  
the projected image on to the  
screen and to hide or black out  
unwanted information (or  
noise). A 0% on the bar scale  
indicates no blanking.  
BLANKING  
AD JU ST THE TOP , BO TTOM,  
LE FT A ND R IGH T BL AN KI NG  
I N OR D ER TO FR AM E  
THE P R OJ EC TED IM AG E  
O NTO TH E S CR E EN .  
The following blanking correc-  
tions are possible :  
- top blanking  
<ENTER> to continue  
<EXIT> to return  
- bottom blanking  
- left blanking  
- right blanking  
Note :  
- if the internal # pattern was  
selected, this pattern re-  
mains on the screen.  
- if the genlocked pattern was  
selected,theexternalsource  
will be displayed.  
Top blanking  
Right blanking  
Left blanking  
Bottom blanking  
7-21  
R5975238 BARCOVISION 701 MULTIMEDIA 070497  
Download from Www.Somanuals.com. All Manuals Search And Download.  
GUIDED ADJUSTMENT MODE  
Topblankingadjustment  
Push the control disk up or  
down to adjust the top blank-  
ing of the setup pattern. Press  
ENTER to continue.  
unwanted information  
(to be blanked out)  
Correct by pushing  
the control disk  
down.  
useful information  
(to be displayed)  
Correct by pushing  
the control disk up  
Bottomblankingadjustment  
Correct by pushing  
the control disk  
down.  
Push the control disk up or  
down to adjust the bottom  
blanking of the setup pattern.  
useful information  
(to be displayed)  
Correct by pushing  
the control disk up.  
unwanted information  
(to be blanked out)  
7-22  
R5975238 BARCOVISION 701 MULTIMEDIA 070497  
Download from Www.Somanuals.com. All Manuals Search And Download.  
GUIDED ADJUSTMENT MODE  
Leftblankingadjustment  
unwanted information  
(to be blanked out)  
Push the control disk to the  
right or to the left to adjust the  
left blanking of the setup pat-  
tern.  
Correct by pushing  
the control disk to  
the right.  
ENTER continues to right  
blanking adjustment.  
EXIT returns to bottom blank-  
ing adjustments.  
Correct by pushing  
the control disk to  
the left.  
useful information  
(to be displayed)  
Rightblankingadjustment  
Push the control disk to the  
right or to the lef to adjust the  
right blanking of the setup pat-  
tern.  
unwanted information  
(to be blanked out)  
Correct by pushing  
the control disk to  
the left.  
Correct by pushing  
the control disk to  
the right.  
useful information  
(to be displayed)  
7-23  
R5975238 BARCOVISION 701 MULTIMEDIA 070497  
Download from Www.Somanuals.com. All Manuals Search And Download.  
GUIDED ADJUSTMENT MODE  
ColorBalance  
Use the control disk to select  
between :  
- Fixed Color Balance (one of  
the 4 predefined values)  
- Custom white balance  
- Custom black balance  
C O L O R B A L A N C E  
FI XE D CO LO R BA LA NC E  
3200  
4900  
6500  
9300  
C US TOM W H ITE B AL A NC E  
C US TOM B L AC K B AL A NC E  
C O N TI N U E  
Fixed Color Balance  
select with arrow keys  
th en <EN TER >.  
You can adjust red with  
4 color temperatures are prepro-  
grammed :  
or  
and blue with  
or  
<EXIT> to return  
- 3200 K (reddish)  
- 4900 K  
892  
- 6500 K (white)  
- 9300 K (bluish)  
Select one of the 4 preprogrammed color temperatures with the control disk and  
press ENTER to display the desired color balance on the screen.  
Press ENTER again to continue.  
CustomWhiteBalance  
Select custom white balance with the control disk and press ENTER to start the  
adjustment. Push the control disk up or down to adjust red gain and push the  
control disk to the right or to the left to adjust the blue gain. A bar scale indicates  
the amount of adjustment.  
Custom Black Balance  
Select custom black balance with the control disk and press ENTER to start the  
adjustment. Push the control disk up or down to adjust the red cut off and push  
the control disk to the right or to the left to adjust the blue cut off.  
When the color balance is adjusted, select continue with the control disk and  
press ENTER.  
7-24  
R5975238 BARCOVISION 701 MULTIMEDIA 070497  
Download from Www.Somanuals.com. All Manuals Search And Download.  
RANDOM ACCESS ADJUSTMENT MODE  
RANDOM ACCESS ADJUSTMENT MODE  
Starting up the random access adjustment mode  
Overview flow chart 'Random Access adjustment mode'  
Selecting Setup Pattern  
Internal cross hatch pattern  
Picture tuning  
Color balance  
Sync Fast/Slow  
Line Doubler  
Enhanced Blue  
Geometryadjustments  
Horizontalphase  
Raster shift adjustment  
Left-rightadjustments  
Top-Bottomadjustments  
Horizontalsize  
Verticallinearity  
Verticalsize  
Blankingadjustments  
Convergenceadjustments  
Colorselect  
8-1  
R5975238 BARCOVISION 701 MULTIMEDIA 070497  
Download from Www.Somanuals.com. All Manuals Search And Download.  
RANDOM ACCESS ADJUSTMENT MODE  
Starting up the random access adjustment mode.  
Push the control disk up or  
down to highlight "RANDOM  
ACCESS" and then press EN-  
TER.  
ADJUSTMENT MODE  
Select  
be lo w:  
a
path from  
G U I D E D  
R A N D O M A C C E S S  
I NS TA LL A TIO N  
S E R V I C E  
Some items in the Random  
access mode are password  
protected (when the password  
functionisenabled). Enteryour  
passwordtocontinue. Allother  
password protected items are  
now also available if you stay  
in the adjustment mode.  
I RI S  
so urce  
1
Select with  
or  
th en < EN TE R>  
<EXIT> to return  
ENTER continues to Setup Pattern Selec-  
tion  
EXIT returns to operational mode  
8-2  
R5975238 BARCOVISION 701 MULTIMEDIA 070497  
Download from Www.Somanuals.com. All Manuals Search And Download.  
RANDOM ACCESS ADJUSTMENT MODE  
Overview flowchart 'Random Access Adjustment' mode  
R AN D O M A C CE S S  
A D JU S TME N T MO D E  
PIC TURE TUN ING  
G EO M E TR Y  
C ON VE R GE NC E  
CO LOR SELE CT  
Select with  
or  
<ENTER> to accept  
<EXIT> to return  
C O LO R S E LE C T  
PI CTURE TU NI NG  
CO LO R B AL AN CE  
R E D  
G R E E N  
B L U E  
R ED A ND GR EE N  
BL UE A ND G RE EN  
RE D AN D BL UE  
SYNC  
:
FAST  
LINE DOUBLER  
:
ON  
Select with  
or  
Select with  
or  
<ENTER> to accept  
<EXIT> to return  
<ENTER> to accept  
<EXIT> to return  
C O NV E R G EN C E  
G E O M E T R Y  
H
P H AS E  
RA STE R SHIFT  
LEFT RIGHT (E-W)  
TOP B OTTO M (N -S)  
SIZE  
L INEAR ITY  
SIZE  
B LA NK IN G  
-
GR EEN ON LY  
RE D O N GRE EN  
BLU E ON GRE EN  
-
H
V
V
Select with  
or  
Select with  
or  
then <ENTE R>  
the n <E NTER >  
<EXIT> to return  
<EXIT> to return  
8-3  
R5975238 BARCOVISION 701 MULTIMEDIA 070497  
Download from Www.Somanuals.com. All Manuals Search And Download.  
RANDOM ACCESS ADJUSTMENT MODE  
G EO M E TR Y  
LE FT-RIG HT  
H
PH ASE  
RASTER SHIFT  
LEFT RIGHT (E-W)  
TOP BOTTOM (N-S)  
SIZE  
LINEARITY  
SIZE  
BLAN KING  
V
V
CENTER LINE BOW  
CENTERLINE SKEW  
RIG HT B OW  
RIGHT K EYSTONE  
LEFT BOW  
-
-
H
V
LEFT KEYSTONE  
V
Select with  
then <ENTER>  
or  
Select with  
or  
then <ENTER>  
<EXIT> to return  
<EXIT> to return  
TO P  
-
B OTTOM  
H
H
CENTER LINE BOW  
CENTERLINE SKEW  
TO P B OW  
TOP KE YSTONE  
BO TTO M B OW  
BOTTOM K EYSTONE  
Select with  
or  
then <ENTER>  
<EXIT> to return  
BL AN KI NG  
T O P  
B OT TO M  
LE FT  
RIGH T  
Select with  
or  
then <ENTER>  
<EXIT> to return  
C ON V ER G E NC E  
CO NV ER GE NC E  
SEL  
:
select area  
using  
arrow keys  
adjust area  
using  
GR EEN ON LY  
RE D ON GRE EN  
BLUE ON GR EEN  
ADJ  
:
arrow keys  
Toggle between  
SEL and ADJ  
with <ENTER>  
Select with  
or  
then <ENTE R>  
<ENTER> continue  
<EXIT> to return  
<EXIT> to return  
8-4  
R5975238 BARCOVISION 701 MULTIMEDIA 070497  
Download from Www.Somanuals.com. All Manuals Search And Download.  
RANDOM ACCESS ADJUSTMENT MODE  
Selecting Setup Pattern  
If an external source is con-  
nected to the projector, the  
path selection menu will be  
displayed. Push the control  
disk up or down to highlight  
the desired setup pattern and  
C h o o s e  
setup pattern  
fro m bel ow:  
a
S E L E C TED S O U R C E  
G E N L O C K ED P A TTE R N  
I NTER N AL P A TTER N  
then press ENTER.  
#
so urce  
1
Genlocked pattern : internally  
generatedcrosshatchpattern,  
locked on the external source.  
Select with  
th en < EN TE R>  
<EXIT> to return  
or  
Internal # pattern : internally  
generatedcrosshatchpattern  
and locked on internal gener-  
ated sync signals. (No exter-  
nal source necessary)  
ENTER continues to Random Access Ad-  
justment Mode or Internal # Pattern Selec-  
tion  
EXIT returns to Path Selection  
ADJUST returns to operational mode  
If no external source is con-  
nected to the projector, the in-  
ternalcrosshatchpatternmenu  
will be displayed.  
The menus in this manual are  
created for an external source,  
connected to one of the inputs,  
and the 'Genlocked pattern' is  
selected.  
8-5  
R5975238 BARCOVISION 701 MULTIMEDIA 070497  
Download from Www.Somanuals.com. All Manuals Search And Download.  
RANDOM ACCESS ADJUSTMENT MODE  
Internal Cross Hatch Pattern  
The Internal # pattern menu  
will be displayed if the internal  
cross hatch pattern has been  
selected or if no source is con-  
nected to the projector.  
INTERNAL  
#
PATTERN  
kHz  
/
Hz  
15.6/50  
15.7/60  
31.2/50  
31.5/60  
31.2/5 0  
31.5/60  
33.7/60  
PAL/SECAM  
NTSC  
EDTV  
IDTV  
The table below lists the fac-  
tory preset frequencies avail-  
able.  
HDTV EUREKA  
HDTV ATV  
HDTV HI-VISION  
Select with  
or  
<ENTE R> to ac cept  
<EXIT> to return  
Push the control disk up or  
down to highlight the desired  
crosshatchfrequencyandthen  
press ENTER.  
kHz/Hz  
ENTER continues to the Random Access  
Adjustment Mode.  
15.6/50  
15.7/60  
31.2/50  
31.5/60  
31.2/50  
31.5/60  
33.7/60  
15.8/60  
21.8/60  
31.5/70  
PAL/SECAM  
NTSC  
EDTV  
EXIT returns to the Setup Pattern Selection  
menu.  
IDTV  
35.8/87  
48.5/60  
44.2/70  
61.0/76  
22.2/60  
VGA 4  
HDTV EUREKA  
HDTV ATV  
HDTV HI-VISION  
EGA 1  
EGA 2  
VGA 1,2  
SUPER VGA 1  
SUPER VGA 2  
SUPER VGA 3  
MAC CLASSIC  
Random access adjustment mode selection menu.  
This is the main menu for the  
Random Access adjustment  
mode.  
RANDOM ACCESS  
ADJUSTMENT MODE  
Through this menu, the follow-  
ing adjustments and features  
are accessible :  
- Picture tuning  
enhanced blue (only for  
P IC TU R E TUN IN G  
G E O M E T R Y  
C O N V E R G E N C E  
C O L O R S E L E C T  
RGB)  
Select with  
<ENTER> t o accept  
<EXIT> to return  
or  
sync slow/fast(video/s-  
video)  
color balance  
- Geometry  
- Convergence  
- Color select  
8-6  
R5975238 BARCOVISION 701 MULTIMEDIA 070497  
Download from Www.Somanuals.com. All Manuals Search And Download.  
RANDOM ACCESS ADJUSTMENT MODE  
Picture tuning  
Highlight Picture tuning by  
pushing the control disk up or  
down and press ENTER.  
The Picture tuning menu will  
be displayed.  
Depending on the input  
source, the Picture tuning  
menu will display different  
items.  
PICTURE TUNING  
C O LO R B A LA N C E  
SY NC  
:
FA ST  
LI NE DOUB LER  
:
ON  
Select with  
<ENTER> t o accept  
<EXIT> to return  
or  
- Color balance  
- Sync slow / fast  
- Line doubling  
- Enhanced blue ON/OFF  
ColorBalance  
The Color Balance function is  
used to select or adjust the  
colortemperatureofwhiteused  
by the projector. The Color  
Balance can be adjusted on  
two different ways :  
PICTURE TUNING  
C O LO R B A LA N C E  
SY NC  
LI NE DOUB LER  
:
FA ST  
- fixed color balance. You  
have the choice between 3200  
K (reddish), 4900 K, 6500 K  
(white) or 9300 K (bluish).  
:
ON  
Select with  
<ENTER> t o accept  
<EXIT> to return  
or  
Fixed Color Balance.  
Highlight one of the 4 prepro-  
grammed color temperatures  
with the control disk and press  
ENTER to display the Color  
Balance.  
C O L O R B A L A N C E  
FI XE D CO LO R BA LA NC E  
3200  
4900  
6500  
9300  
C US TOM W H ITE B AL A NC E  
C US TOM B L AC K B AL A NC E  
C O N TI N U E  
select with arrow keys  
th en <EN TER >.  
You can adjust red with  
or  
and blue with  
or  
<EXIT> to return  
892  
8-7  
R5975238 BARCOVISION 701 MULTIMEDIA 070497  
Download from Www.Somanuals.com. All Manuals Search And Download.  
RANDOM ACCESS ADJUSTMENT MODE  
Custom Color Balance.  
Select custom white balance by pushing the control disk up or down and press  
ENTER to start the adjustment.  
Push the control disk up or  
down to adjust the red gain and  
push the control disk to the left  
or to the right to adjust the blue  
gain. A bar scale indicates the  
amount of adjustment.  
Select custom black balance  
with the control disk and press  
ENTER to start the adjustment.  
Push the control disk up or  
RED GAIN  
down to adjust the red cut-off  
and push the control disk to the  
7 0  
left or to the right to adjust the  
blue cut-off.  
When the color balance is ad-  
justed, select continue by push-  
ing the control disk up or down  
and press ENTER  
SyncFast/SlowAdjustment  
The sync function is used to  
minimize horizontal jittering or  
tearing at the top to the dis-  
PICTURE TUNING  
played image.  
Highlight SYNC with the con-  
trol disk and press ENTER to  
toggle between FAST and  
SLOW.  
C O L O R B A L A N C E  
SY NC  
:
FA ST  
EB U  
O N  
D EC OD IN G  
:
L INE D OU BL ER  
:
Select with  
or  
<ENTER> t o accept  
<EXIT> to return  
Note: SYNC is normally used  
in the SLOW position. The  
FAST position is used to com-  
pensate for unsteady sync  
pulses from older video play-  
back equipment.  
ENTER will toggle Sync between FAST  
and SLOW  
Hint : when the line doubler  
feature is ON (active), toggle  
the sync to FAST.  
EXIT will return to the Randam Access  
Adjustment menu.  
8-8  
R5975238 BARCOVISION 701 MULTIMEDIA 070497  
Download from Www.Somanuals.com. All Manuals Search And Download.  
RANDOM ACCESS ADJUSTMENT MODE  
LineDoubler  
Line doubling is only possible for Video, S-Video or Component Video images on  
standard line frequency.  
To eliminate the video line patterns and to improve the image stability, the line  
doubler has to be switched on. The line doubler is default set in the ON position  
when starting up for the first time. The setting of the line doubler will be saved  
together with the source number. Each time this source number is selected, the  
last saved version will be loaded.  
Highlight Line Doubler with the  
control disk and press ENTER  
to toggle between ON (active)  
and OFF (non active).  
PICTURE TUNING  
C O L O R B A L A N C E  
SY NC  
DE CO DIN G  
LI NE DO UBL ER  
:
FA ST  
I RE  
ON  
:
:
Select with  
or  
<ENTER> t o accept  
<EXIT> to return  
ENTER will toggle Sync between FAST and  
SLOW  
EXIT will return to the Randam Access Ad-  
justment menu.  
EnhancedBlueOn/OffAdjustment  
HighlightENHANCEDBLUEby  
pushing the control disk up or  
down and press ENTER to tog-  
gle between ON and OFF.(only  
available when RGB signals  
are connected)  
When 'Enhanced Blue' is ON,  
the blue color will be displayed  
as cyan.  
PICTURE TUNING  
W HI TE B A LA NC E  
SY NC  
:
FA ST  
EN HAN CED B LUE  
:
ON  
Select with  
<ENTER> t o accept  
<EXIT> to return  
or  
Note: Enhanced blue is only  
used when an RGBS or RGsB  
analog signal from a computer  
is being displayed. Enhanced  
blue is not recommended for  
non computer generated im-  
ages.  
For displaying graphics, this  
'Enhanced Blue' function could  
falsify the color reproduction.  
Inthiscase,putEnhancedBlue  
OFF.  
ENTER will toggle Enhanced Blue be-  
tween ON and OFF  
EXIT will return to the Random access  
main menu.  
ADJUST returns to operational mode  
8-9  
R5975238 BARCOVISION 701 MULTIMEDIA 070497  
Download from Www.Somanuals.com. All Manuals Search And Download.  
RANDOM ACCESS ADJUSTMENT MODE  
ColorSelect  
Highlight COLOR SELECT by  
pushing the control disk up  
and down and press ENTER to  
display the color select menu.  
RANDOM ACCESS  
ADJUSTMENT MODE  
P IC TU R E TUN IN G  
G E O M E T R Y  
C O N V E R G E N C E  
C O L O R S E L E C T  
Select with  
or  
<ENTER> t o accept  
<EXIT> to return  
ENTER continues to the color select menu  
EXIT will return to Internal Crosshatch  
Selection or Setup Pattern Selection Menu  
ADJUST returns to operational mode  
Use the control disk to high-  
light a color (CRT) or combina-  
tion of colors to display the  
projected image in that spe-  
cific color.  
COLOR SELECT  
R E D  
G R E E N  
To select a new color, press  
ENTER, the color selection  
menu appears again on the  
screen. To terminate the color  
select procedure, press EXIT.  
B L U E  
R ED A ND GR EE N  
B LU E AN D GR EE N  
RE D AN D BL UE  
Select with  
<ENTER> t o accept  
or  
<EXIT> to return  
ENTER continues with the selected color or  
color combination.  
EXIT returns to the Random access main  
menu.  
8-10  
R5975238 BARCOVISION 701 MULTIMEDIA 070497  
Download from Www.Somanuals.com. All Manuals Search And Download.  
RANDOM ACCESS ADJUSTMENT MODE  
GeometryAdjustments  
The geometry adjustments have to be done only on the green image. These  
adjustments are automatically implemented for the other color images : Left-right  
(EW) and Top-Bottom corrections, blanking, Horizontal amplitude, vertical  
amplitude, vertical linearity and Horizontal phase.  
Highlight GEOMETRY by  
pushing the control disk up or  
down and press ENTER to dis-  
play the geometry menu.  
RANDOM ACCESS  
ADJUSTMENT MODE  
P IC TU R E TUN IN G  
G E O M E T R Y  
C O N V E R G E N C E  
C O L O R S E L E C T  
Select with  
or  
<ENTER> t o accept  
<EXIT> to return  
ENTER will display Geometry menu  
EXIT will return to Internal Crosshatch Se-  
lection or Setup Pattern Selection Menu  
ADJUST returns to operational mode  
Within the geometry adjust  
menu, the following adjust-  
ments are available :  
GEOMETRY  
H
P H A S E  
R AS TE R S H IFT  
LE FT RI GHT (E- W)  
TO P BO TTOM (N-S)  
S IZE  
LI NE AR ITY  
S IZE  
B L A N K I N G  
- horizontal phase (not for in-  
ternal # pattern).  
- raster shift  
- left-right corrections  
- top-bottom corrections  
- horizontal size  
-
-
H
V
V
Select with  
or  
th en < EN TE R>  
- vertical linearity  
- vertical size  
<EXIT> to return  
- blanking  
ENTER will display the selected option  
EXIT will return to Random Access Adjust-  
ment Mode main menu  
The convergence corrections  
are disabled during geometry  
corrections. The blanking cor-  
rections are only enabled dur-  
ing the blanking adjustments.  
ADJUST returns to operational mode  
8-11  
R5975238 BARCOVISION 701 MULTIMEDIA 070497  
Download from Www.Somanuals.com. All Manuals Search And Download.  
RANDOM ACCESS ADJUSTMENT MODE  
HorizontalPhaseAdjustment  
Push the control disk up or  
down to highlight H PHASE on  
Geometrymenuandthenpress  
ENTER.  
GEOMETRY  
H
P H A S E  
R AS TE R S H IFT  
LE FT RI GHT (E- W)  
TO P BO TTOM (N-S)  
S IZE  
LI NE AR ITY  
S IZE  
B L A N K I N G  
-
-
H
V
V
Select with  
or  
th en < EN TE R>  
<EXIT> to return  
ENTER will select the horizontal phase  
adjustment.  
EXIT returns to the Random access ad-  
justment main menu.  
ADJUST returns to operational mode.  
Note : No horizontal phase  
adjustment is available on the  
internal # pattern.  
For external sources :  
If the raster shift is correctly  
adjusted,thetextboxHphase  
is projected in the middle of  
the raster. At that moment,  
the >< indicates the middle of  
the raster.  
> <  
PHASE  
H
Adjust the hor phase control  
until the middle of the pro-  
jected image is equal with the  
middle of >< .  
7 0  
ENTER continues to geometry menu .  
8-12  
R5975238 BARCOVISION 701 MULTIMEDIA 070497  
Download from Www.Somanuals.com. All Manuals Search And Download.  
RANDOM ACCESS ADJUSTMENT MODE  
Note :  
- if the genlocked pattern was  
selected, the external  
source will be displayed.  
A bar scale and a number indi-  
cator (between 0 and 100) on  
the screen give a visual indica-  
tion of the horizontal phase ad-  
justment.  
Correct by pushing the  
control disk to the right.  
> <  
H
PHASE  
7 0  
Correct by pushing the  
control disk to the left.  
> <  
H
PHASE  
7 0  
8-13  
R5975238 BARCOVISION 701 MULTIMEDIA 070497  
Download from Www.Somanuals.com. All Manuals Search And Download.  
RANDOM ACCESS ADJUSTMENT MODE  
RasterShiftAdjustment  
The green raster must be  
centered both horizontally and  
vertically on the center of the  
CRT surface. To center the  
greenraster,lookintothegreen  
lens and use the control disk  
to move the raster.  
GEOMETRY  
H
P H A S E  
R AS TE R S H IFT  
LE FT RI GHT (E- W)  
TO P BO TTOM (N-S)  
S IZE  
LI NE AR ITY  
S IZE  
-
-
H
V
V
CAUTION  
It is necessary to look  
into the lenses to  
perform these adjust-  
ments. To avoid eye  
C OA R SE S H IF T  
G R EE N H OR I ZO NTA L  
G RE EN VE R TI CA L  
R ED VE RTI CA L  
BL UE V ER TI CA L  
discomfort  
while  
lookingintothelenses,  
reduce the contrast  
andgraduallyincrease  
the brightness level  
until the raster be-  
comes visible on the  
face of the CRT.  
Select with  
<ENTER> t o accept  
<EXIT> to return  
or  
Warning : In order to ensure maximum CRT longevity and to avoid CRT  
damage, do not shift the raster outside the phosphor area of the CRT.  
forbidden area  
projected raster  
crt faceplate border  
phosphor border  
To start the adjustment, use the arrow keys to highlight Raster shift and press  
ENTER to display the coarse shift menu. Select 'Green horizontal' and adjust for  
correct raster position in horizontal direction on the phosphor.  
Continue with 'Green vertical', then with 'Red vertical' and with 'Bleu vertical' until  
the rasters of the 3 tubes correctly centered on the phosphor.  
8-14  
R5975238 BARCOVISION 701 MULTIMEDIA 070497  
Download from Www.Somanuals.com. All Manuals Search And Download.  
RANDOM ACCESS ADJUSTMENT MODE  
correct raster position  
wrong raster position  
Press EXIT to return to the Geometry menu.  
Note : Horizontal and Vertical shifts for Red and Blue should be end up with a  
setting close to 50%. If these settings are significantly greater or lesser than 50%,  
then contact a BARCO authorized service technician.  
8-15  
R5975238 BARCOVISION 701 MULTIMEDIA 070497  
Download from Www.Somanuals.com. All Manuals Search And Download.  
RANDOM ACCESS ADJUSTMENT MODE  
Left-Right(east-west)Adjustments  
Left-right and center adjustments affect only the vertical lines of the projected  
image.  
To start up the left-right and center adjustments, follow the next procedure :  
Push the control disk up or  
down to highlight LEFT-RIGHT  
(E/W) on the geometry menu  
GEOMETRY  
and then press ENTER.  
H
P H A S E  
R AS TE R S H IFT  
LE FT RI GHT (E- W)  
TO P BO TTOM (N-S)  
S IZE  
LI NE AR ITY  
S IZE  
B L A N K I N G  
-
-
H
V
V
Select with  
or  
th en < EN TE R>  
LEFT-RIGHT  
<EXIT> to return  
V
V
C EN TE RL IN E BO W  
CE NTERL IN E SK EW  
R I G HT B O W  
R IG HT KE Y STON E  
L E FT B O W  
L EFT K E YS TON E  
ENTER will select Left-  
Right adjustment menu  
EXIT returns to random ac-  
cess adjustment mode  
main menu.  
Select with  
t he n <E NTER >  
or  
<EXIT> to return  
ADJUST returns to opera-  
tional mode  
Only the green image is displayed while making left-right adjustments. The red  
and blue images will automatically be corrected in the same manner. Conver-  
gence corrections are automatically disabled for the duration of these adjust-  
ments.  
The following adjustments can be executed  
- vertical centerline bow  
- vertical centerline skew  
- side keystone (left - right)  
- side bow (left - right)  
All adjustment are indicated on  
the screen with the function  
name, a bar scale and a number  
between 0 and 100. See next  
example "V Certerline Bow"  
V
CENTERLINE  
B O W  
7 0  
8-16  
R5975238 BARCOVISION 701 MULTIMEDIA 070497  
Download from Www.Somanuals.com. All Manuals Search And Download.  
RANDOM ACCESS ADJUSTMENT MODE  
Adjust the next alignments until the  
vertical lines are straight.  
To enter an alignment, push the  
control disk up or  
down to highlight a  
function and press  
ENTER to activate  
this function.  
Corrects for curvature of the vertical lines in the middle  
of the image.  
Press EXIT to return.  
Corrects the tilting of the vertical lines in the middle of  
the image.  
LEFT-RIGHT  
V
V
C EN TE RL IN E BO W  
CE NTERL IN E SK EW  
R I G HT B O W  
R IG HT KE Y STON E  
L E FT B O W  
Corrects for curvature of the vertical lines on the right side  
L EFT K E YS TON E  
Select with  
t he n < EN TER >  
or  
<EXIT> to return  
Corrects the keystone geometry correction of the vert. lines  
on the right side  
Corrects for curvature of the vertical lines on the left side  
Corrects the keystone geometry correction of the vert. lines  
on the left side  
Correct by pushing  
the control disk to the  
right  
Correct by pushing  
the control disk to  
the left  
8-17  
R5975238 BARCOVISION 701 MULTIMEDIA 070497  
Download from Www.Somanuals.com. All Manuals Search And Download.  
RANDOM ACCESS ADJUSTMENT MODE  
Top-Bottom(north-south)Adjustments  
Top-Bottom and center adjustments affect only the horizontal lines of the  
projected image.  
To start up the Top-Bottom and center corrections, follow the next procedure :  
Push the control disk up or  
down to highlight TOP-BOT-  
TOM (N/S) on the geometry  
GEOMETRY  
menu and then press ENTER.  
H
P H A S E  
R AS TE R S H IFT  
LE FT RI GHT (E- W)  
TO P BO TTOM (N-S)  
S IZE  
LI NE AR ITY  
S IZE  
B L A N K I N G  
-
-
H
V
V
Select with  
or  
th en < EN TE R>  
TOP  
-
BOTTOM  
<EXIT> to return  
H
H
C EN TE RL IN E BO W  
CE NTERL IN E SK EW  
TO P B O W  
TOP K EY S TON E  
B O T TO M B O W  
B O TTO M K E Y S TO N E  
ENTER will select Top-Bot-  
tom adjustment menu  
EXIT returns to random ac-  
cess adjustment mode menu.  
ADJUSTreturnstooperational  
mode  
Select with  
or  
t he n < EN TER >  
<EXIT> to return  
Only the green image is displayed while making top-botton adjustments. The  
red and blue images will automatically be corrected in the same manner.  
Convergence corrections are automatically disabled for the duration of these  
adjustments.  
The following adjustments can be executed :  
- horizontal centerline bow  
- horizontal centerline skew  
- top bow  
- top keystone  
- bottom bow  
- bottom keystone  
All adjustment are indicated  
on the screen with the function  
name,abarscaleandanumber  
between 0 and 100. See next  
H
CENTERLINE  
B O W  
example "H Certerline Bow"  
7 0  
8-18  
R5975238 BARCOVISION 701 MULTIMEDIA 070497  
Download from Www.Somanuals.com. All Manuals Search And Download.  
RANDOM ACCESS ADJUSTMENT MODE  
Adjust the next alignments until  
the vertical lines are straight.  
To enter an alignment, push the  
control disk up or down  
to highlight a function  
and press ENTER to  
activate this function.  
Press EXIT to return.  
Corrects for curvature of the horizontal lines in the  
middle of the image.  
Corrects the tilting of the horizontal lines in the middle  
of the image.  
TOP  
-
BOTTOM  
H
H
C EN TE RL IN E BO W  
CE NTERL IN E SK EW  
TO P B O W  
TOP K EY S TON E  
B O T TO M B O W  
B O TTO M K E Y S TO N E  
Corrects for curvature of the horizontal lines on the upper  
side  
Select with  
or  
t he n <E NTER >  
<EXIT> to return  
Corrects the keystone geometry correction of the hor. lines  
on the upper side  
Corrects for curvature of the horizontal lines on the lower  
side  
Corrects the keystone geometry correction of the hor. lines  
on the lower side  
Correct by pushing  
the control disk down  
Correct by pushing  
the control disk up  
8-19  
R5975238 BARCOVISION 701 MULTIMEDIA 070497  
Download from Www.Somanuals.com. All Manuals Search And Download.  
RANDOM ACCESS ADJUSTMENT MODE  
Horizontal Size Adjustment  
Push the control disk up or  
down to highlight H SIZE on  
the Geometry menu and then  
press ENTER.  
GEOMETRY  
H
P H A S E  
R AS TE R S H IFT  
LE FT RI GHT (E- W)  
TO P BO TTOM (N-S)  
S IZE  
LI NE AR ITY  
S IZE  
B L A N K I N G  
-
-
H
V
V
Select with  
or  
th en < EN TE R>  
<EXIT> to return  
ENTER will select horizontal size adjust-  
ment  
EXIT returns to random access adjustment  
mode menu.  
ADJUST returns to operational mode  
Adjust the horizontal size by  
pushing the control stick to the  
right or to the left until the exact  
image width is obtained.  
Note :  
- if the internal # pattern was  
selected, this pattern re-  
mains on the screen.  
- if the genlocked pattern was  
H size too  
large  
H
SIZE  
7 0  
selected, the external source will be  
displayed.  
A bar scale and a number indicator give  
a visual indication of the horizontal size  
adjustment.  
Ideal image size  
Hint : In order to avoid loss of resolution  
in the projected image and to ensure  
maximum CRT longevity, do not use an  
excessively small horizontal size set-  
ting.  
H size too  
small  
EXIT will return to Geometry  
8-20  
R5975238 BARCOVISION 701 MULTIMEDIA 070497  
Download from Www.Somanuals.com. All Manuals Search And Download.  
RANDOM ACCESS ADJUSTMENT MODE  
VerticalLinearityAdjustment  
The vertical linearity adjust-  
ment function corrects for ver-  
tical non-linearities which ex-  
tend from the center of the im-  
age to the top and bottom of  
the image.  
Push the control disk up or  
down to highlight V LINEAR-  
ITY on the Geometry menu  
and then press ENTER.  
GEOMETRY  
H
P H A S E  
R AS TE R S H IFT  
LE FT RI GHT (E- W)  
TO P BO TTOM (N-S)  
S IZE  
LI NE AR ITY  
S IZE  
B L A N K I N G  
-
-
H
V
V
Select with  
or  
th en < EN TE R>  
<EXIT> to return  
ENTER will select vertical linearity adjust-  
ment  
EXIT returns to random access adjustment  
mode menu.  
ADJUST returns to operational mode  
Adjust the vertical linearity with  
the control disk until the dis-  
tances between the horizontal  
lines of the set up pattern are  
equal.  
V
LINEARITY  
7 0  
EXIT will return to the Geometry menu  
8-21  
R5975238 BARCOVISION 701 MULTIMEDIA 070497  
Download from Www.Somanuals.com. All Manuals Search And Download.  
RANDOM ACCESS ADJUSTMENT MODE  
Vertical Size Adjustment  
Push the control disk up or  
down to highlight V SIZE on  
the Geometry menu and then  
press ENTER.  
GEOMETRY  
H
P H A S E  
R AS TE R S H IFT  
LE FT RI GHT (E- W)  
TO P BO TTOM (N-S)  
S IZE  
LI NE AR ITY  
S IZE  
B L A N K I N G  
-
-
H
V
V
Select with  
or  
th en < EN TE R>  
<EXIT> to return  
ENTER will select vertical size adjustment  
EXIT returns to random access adjustment  
mode menu,.  
ADJUST returns to operational mode  
Adjusttheverticalsizebypush-  
ing the control disk up or down  
until the exact image height is  
obtained.  
V
SIZE  
7 0  
Image too  
tall  
Note :  
- If the internal # pattern was selected, this  
pattern remains on the screen.  
- If the genlocked pattern was selected, the  
external source will be displayed.  
A bar scale and a number indicator give a  
visual indication of the vertical size adjust-  
ment.  
Hint : In order to avoid loss of resolution in the  
projected image and to ensure maximum CRT  
longevity, do not use an excessively small  
vertical size setting.  
Image too  
short  
EXIT will return to Geometry.  
8-22  
R5975238 BARCOVISION 701 MULTIMEDIA 070497  
Download from Www.Somanuals.com. All Manuals Search And Download.  
RANDOM ACCESS ADJUSTMENT MODE  
BlankingAdjustments  
Blanking adjustments affect only the edges of the projected image and are used  
to frame the projected image on to the screen and to hide or black out unwanted  
information (or noise). A 0% on the bar scale indicates no blanking.  
To start up the Blanking adjustments, follow the next procedure :  
Push the control disk up or  
down to highlight BLANKING  
on the Geometry menu and  
GEOMETRY  
then press ENTER.  
H
P H A S E  
R AS TE R S H IFT  
LE FT RI GHT (E- W)  
TO P BO TTOM (N-S)  
S IZE  
LI NE AR ITY  
S IZE  
B L A N K I N G  
-
-
H
V
V
Select with  
th en < EN TE R>  
or  
BLANKING  
<EXIT> to return  
T O P  
B O T T O M  
L E F T  
R I G H T  
ENTER will select blanking  
adjustmentmenu.  
Select with  
t he n <E NTER >  
or  
EXIT returns to random ac-  
cess adjustment mode  
menu.  
<EXIT> to return  
ADJUST returns to opera-  
tional mode  
Thefollowingblankingcorrectionsarepossible:  
- Top blanking  
Top blanking  
- Bottom blanking  
- Left blanking  
- Right blanking  
Right blanking  
Left blanking  
Therefore :  
- If the internal # pattern was  
selected, this pattern remains  
on the screen.  
- If the genlocked pattern was  
selected, the external source  
will be displayed.  
Bottom blanking  
8-23  
R5975238 BARCOVISION 701 MULTIMEDIA 070497  
Download from Www.Somanuals.com. All Manuals Search And Download.  
RANDOM ACCESS ADJUSTMENT MODE  
Adjust the next blanking alignments until the image is correctly framed or the  
unwanted information is blanked out.  
To enter a blanking alignment, push the control disk up or down to highlight a  
function and press ENTER to activate this function.  
Press EXIT to return.  
Adjustment of the blanking on the of the image  
BLANKING  
T O P  
B O T T O M  
L E F T  
Adjustment of the blanking on the bottom of the image  
R I G H T  
Correct by pushing the control disk up or  
down.  
Select with  
t he n <E NTER >  
or  
<EXIT> to return  
Adjustment of the blanking on the left side.  
Adjustment of the blanking on the right side.  
Correct by pushing the control disk to the  
right or to the left.  
8-24  
R5975238 BARCOVISION 701 MULTIMEDIA 070497  
Download from Www.Somanuals.com. All Manuals Search And Download.  
RANDOM ACCESS ADJUSTMENT MODE  
ConvergenceAdjustment  
Convergence adjustments af-  
fect both the horizontal and  
vertical lines of the setup pat-  
tern. These adjustments are  
performed on the red image  
while superimposed on the  
green image and then on the  
blue image while superim-  
posed on the green image.  
CONVERGENCE  
G R E E N O N L Y  
R ED O N G R EE N  
B LU E O N G R EE N  
Select with  
or  
th en < EN TE R>  
Note : the green convergence  
adjustments can be added as  
an option. When these are  
available, start always with  
'green only'. This option will  
<EXIT> to return  
ENTER will display the Convergence  
menu.  
EXITwillreturntoRandomAccessAdjust-  
ment Mode main menu.  
also be indicated on the con-  
vergence menu.  
Highlightfirst'Greenonly'when  
available by pushing the con-  
trol disk up or down and press  
ENTER to display the conver-  
gence adjustment menu  
ADJUST returns to operational mode.  
CONVERGENCE  
SEL  
:
select area  
using  
arrow keys  
adjust area  
using  
ADJ  
:
arrow keys  
Toggle b etween  
SE L an d A DJ  
wi th < ENTE R>  
<EN TER> conti nue  
<EXIT> to return  
ENTERwillcontinuetoconvergenceadjust-  
ment  
EXIT returns to convergence menu.  
8-25  
R5975238 BARCOVISION 701 MULTIMEDIA 070497  
Download from Www.Somanuals.com. All Manuals Search And Download.  
RANDOM ACCESS ADJUSTMENT MODE  
The screen area is divided into 25 areas. Use the control disk to move the box  
tothedesiredzoneandthenpressENTERtobegintheconvergenceadjustment.  
Start the convergence adjustment with zone one and continue as mentioned in  
the diagram hereafter.  
1 5  
1 4  
1 7  
1 6  
2 5  
2 4  
2 3  
2 2  
9
8
5
4
1
2
3
2 0  
2 1  
1 8  
1 9  
6
7
1 2  
1 3  
1 0  
1 1  
3 9 7  
Use the control disk to make  
horizontal or vertical conver-  
gence adjustments in the se-  
lected zone and then press  
ENTER to move the box to  
another zone or EXIT to return  
to the Convergence menu.  
CONVERGE  
ADJUSTMENT  
7 0  
green image  
red image  
ENTER toggles the control disk between  
zone selection and zone adjustment .  
EXIT returns to convergence menu  
8-26  
R5975238 BARCOVISION 701 MULTIMEDIA 070497  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SERVICE MODE  
SERVICE MODE  
Starting up the service mode  
OverviewflowchartServicemode  
ProjectorSetUp  
MemoryManagement  
CommonSettings  
I2CDiagnostics  
R5975228 BARCOVISION 701 MULTIMEDIA 070597  
9-1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SERVICE MODE  
Starting up the Service mode.  
Use the control disk to highlight  
'Service' and then press ENTER.  
ADJUSTMENT MODE  
Select  
below:  
a
path from  
Some items in the Service mode  
are password protected (when the  
password function is active). Enter  
yourpasswordtocontinue. Allother  
password protected items are now  
also free available if you stay in the  
adjustment mode.  
GUI DED  
RANDOM ACCESS  
INSTALLATION  
SERVICE  
IRIS  
source  
1
Select with  
then <ENTER>  
<EXIT> to return  
or  
ENTER continues to the Service Mode  
main menu.  
EXIT returns to the Operational mode.  
SERVICE MODE  
PROJECTORSET-UP  
MEMORY MANAGEMENT  
COMMON SETTINGS  
I2CDIAGNOSTICS  
Select with  
or  
then <ENTER>  
<EXIT> to return.  
9-2  
R5975228 BARCOVISION 701 MULTIMEDIA 070597  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SERVICE MODE  
Overviewflowchart'Service'mode.  
SERVICE MODE  
IDENTIFICATION  
TOTAL RUN TIME  
CHANGEPASSWORD  
CHANGELANGUAGE  
PROJECTORSET-UP  
CHANGEPROJECTORADDRESS  
CHANGEBAUDRATE  
POWER UP MODE  
BARCOLOGO  
COPY A BLOCK  
DELETE A BLOCK  
DELETE ALL BLOCKS  
ALL SETTINGS TO MIDPOS  
R&B CONVERGENCE MID  
MEMORY MANAGEMENT  
GR CONV. MID  
G2 ADJUSTMENT  
CRT RUN IN CYCLE  
PROJECTOR WARM UP  
CRT DRIVE MODE  
COMMON SETTINGS  
I2CDIAGNOSTICS  
R5975228 BARCOVISION 701 MULTIMEDIA 070597  
9-3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SERVICE MODE  
ProjectorSet-up  
Highlight 'Projector Set-Up' by push-  
ing the control disk up or down and  
press ENTER to display the projector  
set-up menu.  
Within the projector set-up menu, the  
following items can be consultated or  
set to the desired setting :  
- Identification  
SERVICE MODE  
PROJECTORSET-UP  
MEMORY MANAGEMENT  
COMMON SETTINGS  
I2CDIAGNOSTICS  
- Total run time  
- Change password  
Select with  
then <ENTER>  
or  
<EXIT> to return.  
- Change language  
- Change projector address  
- Change baudrate  
- Power up mode  
- BARCO logo  
PROJECTORSET-UP  
IDENTIFICATION  
TOTAL RUN TIME  
CHANGEPASSWORD  
CHANGELANGUAGE  
CHANGEPROJECTORADDRESS  
CHANGEBAUDRATE  
POWER UP MODE : operating  
BARCOLOGO  
Select with  
or  
then <ENTER>  
<EXIT> to return.  
Identification  
Highlight 'Identification' with the con-  
trol disk and press ENTER.  
PROJECTORSET-UP  
IDENTIFICATION  
TOTAL RUN TIME  
CHANGEPASSWORD  
CHANGELANGUAGE  
CHANGEPROJECTORADDRESS  
CHANGEBAUDRATE  
POWER UP MODE : operating  
BARCOLOGO  
Select with  
or  
then <ENTER>  
<EXIT> to return.  
ENTER will start the selected item.  
EXIT returns to the Service mode menu.  
9-4  
R5975228 BARCOVISION 701 MULTIMEDIA 070597  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SERVICE MODE  
The 'Identification' screen gives in-  
formation concerning :  
- Projector address. To change the  
address of your projector, contact  
a qualified service technician.  
V 701 MULTIMEDIA  
Proj. addr ess  
Sof t. Ver sion  
:
001  
5.00  
:
- Software version.  
Conf ig.  
:
Ceiling  
front  
Baudr at e PC  
Text O N  
Ser ial No.  
:
9600  
:
- Configuration.  
Possible installations :  
* Front-ceiling  
* Front-table  
:
10359852  
* Rear-ceiling  
* Rear-table  
- Baud rate PC : transfer speed for communication with an IBM PC (or compat-  
ible) or MAC. The baud rate of the projector must be the same as the baud rate  
of the connected computer. When there is a difference, contact a qualified  
service technician to make the appropriate changes.  
- Text ON/OFF  
Indicates in operational mode if the bar scale and number indicator will be  
displayed and if warnings and failures will be displayed.  
ON : displayed  
OFF : not displayed  
The status can be changed by pressing the 'TEXT' key once on the RCU.  
- Serial no. : indicates the fabrication number of the projector. This number can  
be useful when calling for technical assistance.  
Total Run Time  
Highlight 'Total Run Time' with the  
control disk and press ENTER to  
PROJECTORSET-UP  
display the amount of time the pro-  
jector has played since its first start  
up at the factory.  
IDENTIFICATION  
TOTAL RUN TIME  
CHANGEPASSWORD  
CHANGELANGUAGE  
CHANGEPROJECTORADDRESS  
CHANGEBAUDRATE  
POWER UP MODE : operating  
BARCOLOGO  
Select with  
or  
then <ENTER>  
<EXIT> to return.  
ENTER gives the selected item.  
EXIT returns to the Service mode menu.  
ADJUST returns to the Operational mode.  
R5975228 BARCOVISION 701 MULTIMEDIA 070597  
9-5  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SERVICE MODE  
Note : all projectors leave the factory after a burn-in period of approximately 100  
hours.  
Changepassword  
This item is password protected.  
Highlight 'Change Password' with the  
PROJECTORSET-UP  
control disk and press ENTER.  
IDENTIFICATION  
TOTAL RUN TIME  
CHANGEPASSWORD  
CHANGELANGUAGE  
CHANGEPROJECTORADDRESS  
CHANGEBAUDRATE  
POWER UP MODE : operating  
BARCOLOGO  
Select with  
or  
then <ENTER>  
<EXIT> to return.  
ENTER will display the selected item.  
EXIT will return to the Path Selection  
main menu.  
ADJUST will return to the Operational  
mode.  
The current password is displayed.  
The new password must consist of 4  
digits between 0 and 9. Push the  
control disk to the left or to the right to  
select the digits to be changed. Use  
the numeric keys to enter the new  
digits.  
Press ENTER to save the new pass-  
word. Before saving the new pass-  
word, a confirmation screen will be  
displayed.  
PA SSW O RD  
Enter new password  
:
1
9
9
2
Use  
and  
to select,  
and reprogram  
with numeric keys.  
<ENTER> to confirm  
<EXIT> to return  
Press EXIT to return to the Projector  
Set-up menu without saving the new  
password.  
ENTERdisplaystheConfirmationmenu.  
EXIT returns to the Service mode with-  
out saving the new password.  
9-6  
R5975228 BARCOVISION 701 MULTIMEDIA 070597  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SERVICE MODE  
When the displayed password is cor-  
rect, press ENTER to save.  
If not correct, press EXIT to cancel  
the saving.  
CHANGE PASSW ORD  
Password will be  
reprogrammed as XXXX.  
<ENTER> to confirm  
<EXIT> to cancel  
ENTER saves the entered password.  
EXIT returns without saving.  
ChangeLanguage  
The 'Change Language' function of-  
fers the possibility to change the  
language of the screen menus to :  
- English  
- Spanish  
- French  
PROJECTORSET-UP  
IDENTIFICATION  
TOTAL RUN TIME  
CHANGEPASSWORD  
CHANGELANGUAGE  
CHANGEPROJECTORADDRESS  
CHANGEBAUDRATE  
POWER UP MODE : operating  
BARCOLOGO  
- German  
Highlight 'Change Language' with  
the control disk and press ENTER.  
Select with  
then <ENTER>  
<EXIT> to return.  
or  
ENTER selects the Change language  
menu.  
EXIT returns to the Service menu.  
Push the control disk up or down to  
select the desired language and  
press ENTER to change the lan-  
guage.  
LANGUAGE  
ENGLISH  
ESPAÑOL  
FRANCAIS  
DEUTSCH  
Select with  
or  
then <ENTER>  
<EXIT> to return.  
R5975228 BARCOVISION 701 MULTIMEDIA 070597  
9-7  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SERVICE MODE  
Change Projector Address  
Everyprojectorrequiresanindividual  
address between O and 255. This  
address can be software installed.  
To change that address, push the  
control disk up or down to highlight  
'ChangePorjectorAddress'andpress  
ENTER. The Change Projector Ad-  
dress menu will be displayed and the  
actual address will be filled in.  
PROJECTORSET-UP  
IDENTIFICATION  
TOTAL RUN TIME  
CHANGEPASSWORD  
CHANGELANGUAGE  
CHANGEPROJECTORADDRESS  
CHANGEBAUDRATE  
POWER UP MODE : operating  
BARCOLOGO  
Select with  
or  
then <ENTER>  
<EXIT> to return.  
ENTER displays the 'Change Projector  
Address' menu.  
EXIT returns to the Service mode main  
menu.  
The first digit is highlighted. Select  
the individual digits by pushing the  
control disk to the right or to the left.  
Reprogram with the digit keys on the  
RCU.  
PROJECTORADDRESS  
Enternewprojector  
address :  
0 0 0  
Press ENTER to confirm.  
Press EXIT to return to the projector  
set up menu.  
Use  
and  
to select,  
andreprogram  
with numeric keys.  
Highest address is 255  
<ENTER> to confirm  
<EXIT> to return.  
Changebaudrate  
The communication speed between  
projector and computer has 8 pos-  
sible speeds. The baud rate speed  
can be software set up.  
Highlight 'Change Baudrate' by  
pushing the control disk up or down  
and press ENTER to display the  
Baud rate menu.  
PROJECTORSET-UP  
IDENTIFICATION  
TOTAL RUN TIME  
CHANGEPASSWORD  
CHANGELANGUAGE  
CHANGEPROJECTORADDRESS  
CHANGEBAUDRATE  
POWER UP MODE : operating  
BARCOLOGO  
Select with  
or  
then <ENTER>  
<EXIT> to return.  
9-8  
R5975228 BARCOVISION 701 MULTIMEDIA 070597  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SERVICE MODE  
The following baud rates are avail-  
able :  
BAUDRATE  
- 9600  
- 4800  
Selectnew  
baudrate:  
- 2400  
- 1200  
- 600  
9600  
2400  
600  
4800  
1200  
300  
150  
110  
Select with arrow  
keys ;  
- 300  
- 150  
- 110  
<ENTER> to accept  
<EXIT> to return.  
The actual baud rate will be high-  
lighted. To change the baud rate,  
push the control disk up or down  
or to the left or to the right to select  
the desired baud rate and press  
ENTER to accept this baud rate.  
ENTER to accept the selected baud  
rate.  
EXIT to return without changing the  
baud rate.  
Powerupmode  
When pressing the power switch,  
the projector can start up in 'oper-  
ating mode' or in 'stand-by mode'.  
Operating mode : the projector start  
up and displays image .  
Stand-by mode : the projector start  
up in stand-by and waits until the  
stand-by button or a digit key is  
pressed.  
To change the Power up mode,  
select Power Up mode by pushing  
the control disk up or down and  
press ENTER to toggle between  
'Operating' and 'Standby'.  
PROJECTORSET-UP  
IDENTIFICATION  
TOTAL RUN TIME  
CHANGEPASSWORD  
CHANGELANGUAGE  
CHANGEPROJECTORADDRESS  
CHANGEBAUDRATE  
POWER UP MODE : operating  
BARCOLOGO  
Select with  
or  
then <ENTER>  
<EXIT> to return.  
ENTER to toggle between operating and  
standby.  
EXIT to return to the Service menu.  
R5975228 BARCOVISION 701 MULTIMEDIA 070597  
9-9  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SERVICE MODE  
BARCO_logo  
The BARCO logo can be added to the  
image, in overlay or in background,  
on any place on the screen.  
To add the BARCO logo or to change  
a setting in the BARCO logo menu,  
highlight 'BARCO logo' by pushing  
the control disk up or down and press  
ENTER to select.  
PROJECTORSET-UP  
IDENTIFICATION  
TOTAL RUN TIME  
CHANGEPASSWORD  
CHANGELANGUAGE  
CHANGEPROJECTORADDRESS  
CHANGEBAUDRATE  
POWER UP MODE : operating  
BARCOLOGO  
Select with  
then <ENTER>  
<EXIT> to return.  
or  
WARNING : Continuous use of the  
BARCO logo damages the RED  
CRT.  
ENTERdisplaystheBARCOlogomenu.  
EXIT returns to the Service menu  
The BARCO logo menu will be dis-  
played on the screen. Within this  
menu, four toggle settings are avail-  
able.  
Mode [ON/OFF] :  
ON : BARCO logo will be displayed  
on the screen.  
To position the logo on the screen,  
push the control disk up, down, to  
the left or to the right until the  
desired position is reached.  
OFF : No BARCO logo displayed  
on the screen.  
BARCOLOGO  
MODE : ON  
SIZE : SMALL  
BACKGROUND : ON  
ORBITTING : ON  
You can move the logo  
on the screen, using  
the arrow keys.  
WARNING : continuous  
use of the BARCO logo  
damages the RED CRT !  
Select with  
or  
<ENTER> to toggle  
<EXIT> to return.  
Size [SMALL/LARGE] :  
Orbiting [ON/OFF] :  
SMALL : Small BARCO logo will be  
displayed if mode is on.  
LARGE : Large (double size)  
BARCO logo will be displayed if  
mode is on.  
ON : on the BARCO logo will orbit  
around it axis.  
OFF : no orbit of the BARCO logo  
Background [ON/OFF] :  
ON : BARCO logo will be displayed  
on a black background.  
BARCO  
OFF : BARCO logo will be dis-  
played without any background.  
BARCO  
9-10  
R5975228 BARCOVISION 701 MULTIMEDIA 070597  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SERVICE MODE  
Memorymanagement  
Highlight 'Memory management' by  
pushing the control disk up or down  
and press ENTER to display the  
memory management menu.  
Within the memory management  
menu, the following items can be  
consultated or executed :  
- copy a block  
SERVICE MODE  
PROJECTORSET-UP  
MEMORY MANAGEMENT  
COMMON SETTINGS  
I2CDIAGNOSTICS  
- delete a block  
- delete all blocks  
- all settings to midposition  
- R & B convergence to mid  
- Gr convergence mid (only if green  
convergence is available)  
Select with  
then <ENTER>  
<EXIT> to return.  
or  
MEMORY MANAGEMENT  
COPY A BLOCK  
DELETE A BLOCK  
DELETE ALL BLOCKS  
ALL SETTINGS TO MIDPOS  
R & B CONVERGENCE MID  
GR CONVERGENCE MID  
Select with  
or  
then <ENTER>  
<EXIT> to return.  
Copyablock  
The copy a block function copies  
the settings of a selected block into  
the active block.  
Highlight copy a block with the con-  
trol disk and press ENTER.  
MEMORY MANAGEMENT  
COPY A BLOCK  
DELETE A BLOCK  
DELETE ALL BLOCKS  
ALL SETTINGS TO MIDPOS  
R & B CONVERGENCE MID  
GR CONVERGENCE MID  
Select with  
or  
then <ENTER>  
<EXIT> to return.  
ENTER will select the highlighted item.  
EXIT returns to the Path Selection main  
menu.  
ADJUST returns to the Operational mode.  
R5975228 BARCOVISION 701 MULTIMEDIA 070597  
9-11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SERVICE MODE  
To copy the settings of a closed  
block to the block you are working on  
(active block), use the control disk to  
select a block.  
All existing settings will be overwritten  
with the new settings.  
COPY MODE  
Nr. Src Fh  
Fv  
inp  
conf.  
FC  
1
2
3
4
5
6
7
8
1
3
-
2
-
15.6 50  
31.2 60  
15.6 50  
31.5 50  
33.7 60  
video  
RGB3S RT  
intern FC  
RGB3S FC  
intern FC  
Press ENTER to copy the selected  
block. A confirmation screen will be  
displayed.  
Active block nr.  
or  
1
Select with  
<ENTER> to copy  
<EXIT> to return  
ENTER displays a confirmation screen.  
EXIT returns to the Service Mode main  
menu.  
If you are certain you wish to copy  
the contents of the selected block  
into the active block, press ENTER.  
EXIT cancels the copy procedure  
and returns without copying the block.  
COPY BLOCK  
Settings  
in current block  
wil be overwritten  
!
<ENTER> to confirm  
<EXIT> to cancel  
Deletionofblocks  
This item is password protected.  
The delete function is used to clear  
all data (settings) from an adjust-  
ment block.  
A delete can be given :  
- block by block  
or  
- for all blocks.  
9-12  
R5975228 BARCOVISION 701 MULTIMEDIA 070597  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SERVICE MODE  
Deletingblockbyblock  
MEMORY MANAGEMENT  
The 'delete a block' function deletes  
the settings of a selected block.  
Highlight 'Delete a block' with the  
control disk and press ENTER.  
COPY A BLOCK  
DELETE A BLOCK  
DELETE ALL BLOCKS  
ALL SETTINGS TO MIDPOS  
R & B CONVERGENCE MID  
GR CONVERGENCE MID  
Select with  
or  
then <ENTER>  
<EXIT> to return.  
ENTER will select the pointed item.  
EXIT returns to the Path Selection main  
menu.  
ADJUST returns to the Operational mode.  
Push the control disk up or down to  
select the desired adjustment block.  
Press ENTER to delete the selected  
adjustment block. A confirmation  
menu will be displayed.  
DELETE MODE  
Nr. Src Fh  
Fv  
inp  
conf.  
FC  
1
2
3
4
5
6
7
8
1
3
-
2
-
15.6 50  
31.2 60  
15.6 50  
31.5 50  
33.7 60  
video  
RGB3S RT  
intern FC  
RGB3S FC  
intern FC  
Active block nr.  
or  
1
Select with  
<ENTER> to copy  
<EXIT> to return  
ENTER displays the confirmation menu.  
EXIT returns to the Service Mode main  
menu.  
DELETE BLOCK  
The selected block  
will be deleted  
!
<ENTER> to confirm  
<EXIT> to cancel  
ENTER will delete the selected block.  
EXIT cancels the deletion procedure and  
returns to the Service mode main menu.  
R5975228 BARCOVISION 701 MULTIMEDIA 070597  
9-13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SERVICE MODE  
Deletionofallblocks  
Highlight 'delete all blocks' with the  
control disk and press ENTER.  
MEMORY MANAGEMENT  
COPY A BLOCK  
DELETE A BLOCK  
DELETE ALL BLOCKS  
ALL SETTINGS TO MIDPOS  
R & B CONVERGENCE MID  
GR CONVERGENCE MID  
Select with  
or  
then <ENTER>  
<EXIT> to return.  
ENTER gives a confirmation message  
before deleting.  
EXIT returns to the Path Selection  
main menu.  
If you are certain you wish to delete  
all blocks, press ENTER to confirm,  
otherwise press EXIT to return.  
Once ENTER is pressed, all block  
headers and adjustment settings are  
permanently removed and cannot be  
restored.  
DELETE ALL BLOCKS  
All 32 blocks  
will be deleted  
!
<ENTER> to confirm  
<EXIT> to cancel  
Allsettingstomidposition  
Item is password protected.  
Highlight 'All settings to midposition'  
with the control disk and press EN-  
TER to set all settings to their  
midposition.  
MEMORY MANAGEMENT  
COPY A BLOCK  
DELETE A BLOCK  
DELETE ALL BLOCKS  
ALL SETTINGS TO MIDPOS  
R & B CONVERGENCE MID  
GR CONVERGENCE MID  
A confirmation menu will be displayed  
first.  
Select with  
or  
then <ENTER>  
<EXIT> to return.  
ENTER displays a Confirmation screen.  
EXIT returns to the Service menu.  
9-14  
R5975228 BARCOVISION 701 MULTIMEDIA 070597  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SERVICE MODE  
ENTER will set all settings to their  
midposition. EXIT will cancel the  
operation to set all settings to their  
midposition.  
ALL SETTINGS TO M IDPOSITION  
All settings  
in current block  
wil be overwritten  
!
<ENTER> to confirm  
<EXIT> to cancel  
Undoallsettingstomidpos  
When "All settings to midpos" is  
selected, all settings are set to their  
midposition. To cancel this action,  
select 'Undo all settings to midpos'  
by pushing the control disk up or  
down and press ENTER. 'Undo all  
settings to Midposition' is displayed  
in the Memory management menu  
in stead off 'All settings to  
midposition' when this latter is  
pressed.  
MEMORY MANAGEMENT  
COPY A BLOCK  
DELETE A BLOCK  
DELETE ALL BLOCKS  
UNDO ALL SETTINGS TO MIDPOS  
R & B CONVERGENCE MID  
GR CONVERGENCE MID  
Select with  
or  
then <ENTER>  
<EXIT> to return.  
An undo is possible as long as the  
projector is playing on the same  
source (= same adjustment block)  
even when some adjustments as  
geometry or convergence are al-  
ready readjusted. When undo is  
presssed all settings are reset to  
the previous settings.  
R & B convergence mid  
Item is password protected.  
Highlight 'R & B convergence mid'  
with the control disk and press  
ENTER to set all convergence set-  
tings to their midposition. A confir-  
mation screen will be displayed  
first.  
MEMORY MANAGEMENT  
COPY A BLOCK  
DELETE A BLOCK  
DELETE ALL BLOCKS  
ALL SETTINGS TO MIDPOS  
R & B CONVERGENCE MID  
GR CONVERGENCE MID  
Select with  
or  
then <ENTER>  
<EXIT> to return.  
R5975228 BARCOVISION 701 MULTIMEDIA 070597  
9-15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SERVICE MODE  
ENTER sets the convergence set-  
tings to their midposition. EXIT can-  
cels the procedure to set the conver-  
gence settings to their midposition.  
R
&
B
CONVERGENCE MID  
Conver gence set t ings  
in cur rent block  
wil be overwritt en  
!
<ENTER> t o conf ir m  
<EXIT> t o cancel  
UndoR&Bconvergencemid  
When "R & B convergence mid" is  
selected, all convergence settings  
are set to their midposition. To  
cancel this action, select 'Undo R &  
B convergence mid' by pushing the  
control disk up or down and press  
ENTER. 'Undo R & B convergence  
mid' is displayed in the Memory man-  
agement menu in stead off 'R & B  
convergence mid' when this latter is  
pressed.  
MEMORY MANAGEMENT  
COPY A BLOCK  
DELETE A BLOCK  
DELETE ALL BLOCKS  
ALL SETTINGS TO MIDPOS  
UNDO R & B CONVERGENCE MID  
GR CONVERGENCE MID  
Select with  
or  
then <ENTER>  
<EXIT> to return.  
An undo is possible as long as the  
projector is playing on the same  
source (= same adjustment block)  
even when some adjustments are  
already readjusted. When undo is  
presssed all settings are reset to the  
previous settings.  
Greenconvergencemid  
Only available when the projector is  
equipped with green convergence  
adjustmentes.  
Highlight 'Gr convergence mid' by  
pushing the control disk up or down  
and press ENTER to switch off the  
green convergence.  
MEMORY MANAGEMENT  
COPY A BLOCK  
DELETE A BLOCK  
DELETE ALL BLOCKS  
ALL SETTINGS TO MIDPOS  
R & B CONVERGENCE MID  
GR CONVERGENCE MID  
Select with  
or  
then <ENTER>  
<EXIT> to return.  
9-16  
R5975228 BARCOVISION 701 MULTIMEDIA 070597  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SERVICE MODE  
Undogreenconvergencemid  
Only available when the projector  
is equipped with green conver-  
gence adjustmentes.  
The item 'Undo green convergence  
mid' will automatically be displayed  
when the green convergence is  
switched to midposition.  
MEMORY MANAGEMENT  
COPY A BLOCK  
DELETE A BLOCK  
DELETE ALL BLOCKS  
ALL SETTINGS TO MIDPOS  
R & B CONVERGENCE MID  
UNDO GR CONVERGENCE MID  
PressENTERtoswitchonthegreen  
convergence.  
Select with  
or  
then <ENTER>  
<EXIT> to return.  
CommonSettings  
Highlight 'Common settings' by push-  
ing the control disk up or down and  
press ENTER to display the com-  
mon settings menu.  
Within the common settings menu,  
the following items can be set up or  
executed :  
SERVICE MODE  
PROJECTORSET-UP  
MEMORY MANAGEMENT  
COMMON SETTINGS  
I2CDIAGNOSTICS  
- G2 adjustment  
- CRT run in cycle  
- Projector warm up  
Select with  
then <ENTER>  
or  
<EXIT> to return.  
COMMON SETTINGS  
G2 ADJUSTMENT  
CRT RUN IN CYCLE  
PROJECTOR WARM UP  
Select with  
or  
then <ENTER>  
<EXIT> to return.  
R5975228 BARCOVISION 701 MULTIMEDIA 070597  
9-17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SERVICE MODE  
G2Adjustment  
Item is password protected.  
Highlight 'G2 adjust' with the control  
disk and press ENTER to continue.  
COMMON SETTINGS  
G2ADJUSTMENT  
CRT RUN IN CYCLE  
PROJECTOR WARM UP  
Select with  
or  
then <ENTER>  
<EXIT> to return.  
A safety notice will be displayed on  
the screen as it is necessary to open  
the top cover to adjust the G2.  
SAFETY  
NOTICE  
RISK OF ELECTRICAL SHOCK  
G2 ADJUSTMENT SHOULD BE  
PERFORMED  
BY BARCO PERSONNEL,  
OR BARCO AUTHORIZED  
DEALERS.  
'G2 adjustment should be per-  
formed by BARCO personnel, or  
BARCO authorized dealers'.  
If you are qualified, press ENTER to  
continue. If not qualified, press EXIT  
to return to the Common settings  
menu. Further description of the G2  
adjustment is given in the Installation  
manual.  
IF QUALIFIED, PRESS  
<ENTER> TO CONTINUE, OR  
IF NOT, <EXIT> TO RETURN.  
ENTER selects the G2 adjustment.  
EXIT returns to the Common settings  
menu.  
ADJUST returns to the Operational mode.  
9-18  
R5975228 BARCOVISION 701 MULTIMEDIA 070597  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SERVICE MODE  
CRT run in cycle  
TheCRTrunincycleoptioncanonlybeactivatedwhenmemoryblocksonaninternal  
#patternareavailable. Whenoneormoresuchblocksareavailable,aflashingwhite  
image (5sec on, 5 sec off) is generated and that for 5 min on the first internal block.  
In the next 5 min, a second internal block will be used to generate the flashing white  
image. The image will also be shifted in a vertical way to prevent a CRT burn in. To  
quit the CRT run in cycle option, press EXIT.  
Highlight 'CRT run in cycle' with  
the control disk and press EN-  
COMMON SETTINGS  
TER to start.  
G2 ADJUSTMENT  
CRT RUN IN CYCLE  
PROJECTOR WARM UP  
Select with  
or  
then <ENTER>  
<EXIT> to return.  
ENTERselectstheCRTrunincycleoption.  
EXIT returns to the Path Selection main  
menu.  
If a memory block adjusted on an  
internal # pattern is available, the  
CRT run in cycle will start when  
pressingENTER. Ifnosuchablock  
is available, the projector cannot  
runtheCRTruninoptionandleaves  
theadjustmentmode.  
If you still want to run CRT run in  
cycle, create first a memory block  
on an internal # pattern and restart  
the CRT run in option.  
CRT RUN IN CYCLE  
A
flashing white pattern  
will be generated until  
<EXIT> is pressed.  
The projector only uses  
memory blocks adjusted  
on an internal  
#
pattern;  
if no such block is  
available, the projector  
can't run the procedure  
and leaves the adjustment  
m od e .  
<ENTER> to continue  
<EXIT> to cancel  
ENTER starts the 'CRT run in' when an  
internal generated # pattern is available.  
EXIT returns to the Path Selection main  
menu.  
R5975228 BARCOVISION 701 MULTIMEDIA 070597  
9-19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SERVICE MODE  
Projectorwarmup  
Highlight 'Projector warm up' by push-  
ing the control disk up or down and  
press ENTER to select the projector  
warm up menu.  
COMMON SETTINGS  
G2 ADJUSTMENT  
CRT RUN IN CYCLE  
PROJECTOR WARM UP  
Select with  
or  
then <ENTER>  
<EXIT> to return.  
The ON/OFF option can be toggled  
with the ENTER key.  
PROJECTOR WARM UP  
When in the ON position (and the  
CRT run in cycle is OFF), the projec-  
tor can start up with a warm up  
periode of 20 minutes. During the  
start up a warm up menu will be  
displayed. This menu offers the  
possibilitytoskipthewarmupperiode  
anyway by pressing the EXIT key  
and offers the possibility to adjust  
the horizontal and vertical amplitude  
of this white image with the control  
disk. During this warm up period, a  
full white image is shifted on the CRT  
faceplate to avoid a burn in.  
OPTION : ON  
A FULL WHITE PATTERN  
WILL BE GENERATED FOR  
20 MINUTES AT POWER UP  
AFTER THIS PROCEDURE  
THE PROJECTOR IS READY  
TO PERFORM IN OPTIMUM  
CONDITION  
TOGGLE OPTION ON OR OFF  
with <ENTER>  
<EXIT> to return  
Every 30 seconds a text box will be  
displayed on another place on the  
screen with the remaining time to go.  
When EXIT is pressed during this  
warm up periode, the warm up menu  
will be redisplayed with the remain-  
ing time indication. Press another  
time EXIT to interrupt the warm up  
cycle.  
When the warm up option is OFF,  
when switching on the projector, it  
starts immediately with the projec-  
tion of the selected source  
9-20  
R5975228 BARCOVISION 701 MULTIMEDIA 070597  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SERVICE MODE  
I2CDiagnostics  
Highlights 'I2C Diagnostics' by  
pushing the control disk up or  
down and press ENTER.  
SERVICE MODE  
The I2C diagnostics menu gives  
an overview of the I2C failures  
inside the projector.  
PROJECTORSET-UP  
MEMORY MANAGEMENT  
COMMON SETTINGS  
I2CDIAGNOSTICS  
Select with  
or  
then <ENTER>  
<EXIT> to return.  
To scroll through the failure list, push  
the control disk up or down.  
The I2C address, IC number and  
module name will be given in I2C  
diagnostic menu.  
When no errors are detected, the  
following message will appear on the  
screen :  
I2CDIAGNOSTICS  
Failures :  
ICnumber mod.name  
addr  
48H  
IC200  
DECODER  
"No errors on i2c-bus detected".  
Scroll with  
or  
then <ENTER>  
<EXIT> to return.  
R5975228 BARCOVISION 701 MULTIMEDIA 070597  
9-21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SERVICE MODE  
9-22  
R5975228 BARCOVISION 701 MULTIMEDIA 070597  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MESSAGES, WARNINGS AND FAILURES  
MESSAGES, WARNINGS AND FAILURES  
R5975228 BARCOVISION 701 MULTIMEDIA 070497  
10-1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MESSAGES, WARNINGS AND FAILURES  
When selecting a new source, information about this  
sourcewillbedisplayedonthescreen. Sourcenumber,  
horizontal and vertical frequencies of the displayed  
source.  
INPUT 01  
Fh= 15.6 kHz  
Fv= 050 Hz  
Announcement of the selected source.  
SOURCE 01  
Messagetoenteryourpassword. Passwordcontains4  
digits.  
enter  
password  
x x x x  
These messages will be displayed on the screen when  
pushing the TEXT key.  
text on  
Text ON : the 'bar scale indication' will be enabled  
during the change of an analog control in the 'opera-  
tional mode' + all warnings and failures will be dis-  
played.  
Text OFF : the 'bar scale indication' will be disabled  
duringthechangeofananalogcontrolinthe'operational  
mode' + all warnings and failures will not be displayed.  
text off  
Indication of the projector address when activating the  
'ADDRESS' button on the RCU with a pencil or other  
small object.  
PROJECTOR  
ADDRESS :  
003  
WARNING :  
When using the projector with the RCVDS, this warning  
will be displayed when selecting an input slot of an  
RCVDS where the input board is missing.  
input not  
available  
10-2  
R5975228 BARCOVISION 701 MULTIMEDIA  
070497  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MESSAGES, WARNINGS AND FAILURES  
WARNING :  
Theinputisavalidinputbutthesourceisnotconnected  
totheinputterminalsortheinputsourceisswitchedoff.  
source not  
available  
WARNING :  
When a wrong key is pressed on the RCU.  
invalid  
key entry  
WARNING :  
Message when the entered password is wrong.  
invalid  
code entry  
WARNING :  
End of adjustment range.  
end of ad-  
just range  
WARNING :  
input no  
longer  
Message will be displayed when the input source is no  
longer available. The following message then appears:  
'check input signal or select new source'.  
available  
Message will be displayed after the message 'input no  
longer available'. It asks to check the connections  
between the source and the projector or to check if the  
source is switched on.  
check in-  
put signal  
or select  
new source  
Itwarnsyoutocheckthepowerconnectionorthepower  
status of the RCVDS.  
WARNING :  
input se-  
Nextmessagewillappearimmediatlyonthescreen:'go  
tostand-by'.  
lector not  
available  
R5975228 BARCOVISION 701 MULTIMEDIA 070497  
10-3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MESSAGES, WARNINGS AND FAILURES  
WARNING :  
Projectorwillswitchto'stand-by'whentheRCVDSisno  
longer available.  
go to  
stand by  
WARNING :  
invalid  
frequency  
input  
The entered frequency or applied frequency of the  
source is out of the projector's range.  
Message to inform that selected table is deleted. This  
messagewillbefollowedby'confirmmessage',onwhich  
the user has to answer.  
table is  
deleted  
FAILURE  
Hardware failure. Call a qualified service technician for  
repair.  
I2C error  
addr. : 7FH3  
FAILURE  
short  
circuit on  
I2C bus  
Hardware failure. Call a qualified service technician for  
repair.  
FAILURE  
RCVDS com-  
munication  
error  
Serial communication error between the RCVDS and  
the projector.  
FAILURE  
IRIS commu-  
nication  
Communication error between IRIS 800 and the projec-  
tor. Call a qualified service technician.  
error  
WAIT  
starting  
up  
Message during the start up of the IRIS 800. Message  
will disappear when the IRIS 800 is ready to accept  
commands.  
IRIS  
10-4  
R5975228 BARCOVISION 701 MULTIMEDIA  
070497  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPTIONS  
OPTIONS  
IR receiver 800  
Hardwired RCU  
Projector Control software  
RCVDS 05  
VS05  
Adapter and communication cables  
Ceiling mount CM50  
Soft edge matching  
Contrast modulation  
Picture Orbiting  
R5975238 BARCOVISION 701 MULTIMEDIA 070497  
11-1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPTIONS  
IR Receiver 800  
This infrared receiver unit makes it possible to control the projector from another  
room.  
ThereisacommunicationlinewithcablebetweentheIRreceiverandtheprojector  
or the RCVDS05. The control information from the RCU can now be sent to this IR  
receiver.  
The IR receiver 800 displays the selected source on a 7-segment display.  
Order number : R9827515.  
Communication cable  
IR Remote Receiver 800  
BARCODATA 701S  
S cr ee n  
Control room  
Projection room  
Hardwired RCU.  
ThecontrolsignalsfromtheRCUcanbesenttotheprojectorviaawiredconnection.  
Preparing your remote cable :  
Use a shielded cable with a maximum length of 100 m and two mini-jack 3.5 mm  
connectors (order number : R313043).  
- Peel back the vinyl covering of the cable on both sides and twist the wire core.  
- Solder a jack plug as shown in drawing above to each end of the cable.  
shield  
conductor  
shield = ground  
conductor = data information  
When the cable is ready, plug one side in the remote control and the other side in  
the connector on the rear of the projector labelled ‘remote’.  
11-2  
R5975238 BARCOVISION 701 MULTIMEDIA 070497  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPTIONS  
Projector Control software  
Only available for projectors equipped with the optional RS232 communication  
port.  
The software is user-friendly and makes full use of : mouse control, pull down  
menus and dialog boxes.  
Two main applications are available with this software : remote control and  
transferring and receiving data of projector settings.  
remote control simulation. Advantage : address range 0 to 15.  
adjustment data : where can it be located when an IBM PC (or compatible) or  
MAC or Workstation is connected :  
- hard memory device with files of settings.  
- the contents of the local memory of the computer.  
- the contents of the projector.  
RCVDS 05  
An optional RCVDS 05 source selector makes it possible to connect up to 20  
sourcestotheprojector. WhenRCVDS'sarelinkedviatheexpansionmodule,even  
90 inputs can be connected to the projector.  
The selected source number will be displayed on a 2 digit display and the selected  
input module will be indicated with a LED on the rear.  
VS05  
The VS05 is a versatile Video and HDTV source selector for all BARCO's digitally  
controlled large screen projectors. It offers the possibility to connect and switch  
up to 5 different Video sources, 3 different S-Video sources and 1 RGB Analog  
source to a BARCO projector. In addition, the audio signal proper to the source,  
can be switched to an audio amplifier.  
Adapter and communication cables  
BARCO provides several cables to connect peripheral equipment to the projector.  
a. D9-D9 communication cable  
- To connect an IBM PC (or compatible) to the projector. (only if the optional  
RS232 port is installed.)  
- To connect an RCVDS to the projector.  
- To connect an IR receiver to the RCVDS05 or to the projector.  
- To be used as extension cable for all other adapter cables.  
Available length :5 m (16ft), order number R982770; 15 m(50ft), order number  
R9827560; and 30 m (100ft), order number R9827570  
R5975238 BARCOVISION 701 MULTIMEDIA 070497  
11-3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPTIONS  
b. Din Mini8-D9 adapter cable.  
- To connect a Macintosh computer to the projector.  
Available length : 1 m, order number R9827640.  
c. D25-D9 adapter cable  
- To connect a workstation to the projector.  
Available length : 1 m, order number R9827630  
Ceiling mount CM50  
ThissuspensionsystemenablestomountanyprojectorfromtheBARCO700series  
to the ceiling without using any mechanical interface, and to adapt the projector  
perfectly to the local mounting requirements.  
Order number CM50 with pulley : R9827990  
Order number CM50 without pulley : R9827991.  
Orbiting Kit  
Static pictures are very often shown on large screen projectors, especially in  
processcontrolandpresentationapplications. Duetothefactthatthesamepicture  
information is shown for a long period in the same place, picture tubes can be  
damaged by 'local burn-in'. To avoid this problem, a special Orbiting circuit is  
availablewhichmovesthepictureveryslowlyaroundapredefinedscreenarea. The  
cycletimeisverylongtomakethemovementoftheprojectedimageimperceptible.  
The use of the orbiting kit is described in appendix A.  
Order number : R9827780  
Soft edge matching kit  
Multi-screens are popular for many applications. In these installations, the goal is  
to obtain a contiguous matched image, forming one homogenous view. The soft  
edge matching feature provides a solution to the annoying side effects when  
adjusting two or more projected images next to each other. To improve this  
junction, both images must be overlapping within a certain percentage of the total  
screen width. During the overlapping period, both video signals are modulated  
by appropriate waveforms so that the resulting light output equals the rest of the  
image.  
Contrast modulation kit  
Thecontrastmodulationkitisdesignedtoimproveoveralllightoutputuniformityand  
toovercometheinherentcolorshifterrors,normallyassociatedwithCRTprojection.  
The laws of physics applied to projection optics dictate that the center of the  
projected image will be brighter than the corners, this phenomenon is normally  
referredtoas'cornerfalloff'. Duetothenormaloff-axisprojectionoftheredandblue  
images,CRTprojectiondisplaysaphenomenonreferredtoas'colorshift',whereby  
onesideoftheimageisreddishandtheotherblueish. Bymodulatingtheamplitude  
of the video signal with appropriate waveforms we are able to overcome both  
problems.  
The use of this contrast modulation kit is described in appendix C.  
Order number : R9827800  
11-4  
R5975238 BARCOVISION 701 MULTIMEDIA 070497  
Download from Www.Somanuals.com. All Manuals Search And Download.  
APPENDIX A : BATTERY REPLACEMENT IN THE RCU  
Battery replacement in the RCU.  
Removethebatterycoveronthebacksideoftheremote  
control by pushing the indicated handle a little to the  
bottomoftheRCU. Liftupthetopsideofthecoveratthe  
same time (fig. 1).  
Removethebatteryfromthecompartmentanddiscon-  
nect the contact plate (fig. 2).  
Connect a new 9 V battery (type E-block, e.g. 6F22S  
or equivalent) to the contact plate.  
Insert the battery back into the compartment and put  
the cover back.  
Attention:whenanewbatteryisinstalled,theprojector  
address must be reprogrammed before using the  
RCU.  
fig.1  
Contact  
plate  
Battery  
fig.2  
310a.DRW  
R5975238 BARCOVISION 701 MULTIMEDIA 070497  
A-1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
APPENDIX A : BATTERY REPLACEMENT IN THE RCU  
A-2  
R5975238 BARCOVISION 701 MULTIMEDIA 070497  
Download from Www.Somanuals.com. All Manuals Search And Download.  
APPENDIX B : ORBITING  
Orbiting (option)  
Static pictures are very often shown on large screen projectors, especially in  
process control and presentation applications. Due to the fact that the same picture  
information is shown for a long period on the same place, picture tubes can be  
damaged by 'local burn-in'. To avoid this problem, BARCO has designed special  
Orbiting circuitry which moves the picture very slowly around a predefined screen  
area. The orbiting circuitry has been designed using a very long cycle time to make  
the movement of the projected image imperceptible.  
Adjustment procedure :  
The orbiting path is automatically added to the Random Access Adjustment mode  
menu when installed.  
Press ADJUST to enter the Ad-  
justment mode and select Ran-  
dom.  
R AN DO M A CC ES S  
AD JUS TME NT MO DE  
The Random Access Adjustment  
PICTURE TUNING  
Mode menu will be displayed.  
Highlight ORBITING with the con-  
trol disk and press ENTER.  
G EO M E TR Y  
CO NV ERG EN CE  
COL OR SEL ECT  
COLO R BALA NCE  
ORBI TING  
CONTR . MODULA TION  
SOFT ED GE  
Select with  
or  
<ENTER> to accept  
<EXIT> to return  
63 6f  
ENTER continues to the Master Orbiting  
menu.  
EXIT returns to the Operational mode.  
ADJUST returns to the Operational mode.  
Orbitingmodetoggleswitches  
The orbiting module is provided with a three pin connector for connection with the  
BARCO's BCl link option module, used in multiple projector installations. For  
Orbiting, one projector operates as master whereas the others operate as slave.  
R5975238 BARCOVISION 701 MULTIMEDIA 070497  
B-1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
APPENDIX B : ORBITING  
Master/slavetoggle  
Highlight 'CHANGE TO SLAVE'  
with the control disk and press  
ENTER to set the projector as  
Slave.  
M ASTER O RBITING  
CHANGE TO SLAVE  
MO DE : ON  
SPEED: FAST  
ADJUST DEVIATION  
SELECT WITH  
OR  
THE N <ENTER>  
DEVIATION ADJUST  
:
VERTICAL WITH  
HORIZONTAL WITH  
OR  
OR  
<EXIT> to return  
Highlight 'CHANGE TO MASTER'  
with the control disk and press  
ENTER to set the projector as  
Master.  
SLAVE O RBITING  
CHA NGE TO MAS TER  
ADJUST DEVIATION  
SELECT WITH  
OR  
THE N <ENTER>  
DEVIATION ADJUST  
:
VERTICAL WITH  
HORIZONTAL WITH  
OR  
OR  
<EXIT> to return  
OrbitingON/OFFtoggle(onlyinMasterOrbiting)  
Highlight 'MODE : ON' with the  
control disk and press ENTER to  
set the ORBITING OFF.  
Highlight 'MODE : OFF' with the  
control disk and press ENTER to  
set the ORBITING ON.  
M ASTER O RBITING  
CHANGE TO SLAVE  
MO DE: ON  
SPEED: FAST  
ADJUST DEVIATION  
SELECT WITH  
OR  
TH EN < ENTE R>  
DEVIATION ADJUST  
:
VERTICAL WITH  
HORIZONTAL WITH  
OR  
OR  
<EXIT> to return  
ENTER toggles between mode on and  
off.  
EXIT returns to the Path Selection menu.  
B-2  
R5975238 BARCOVISION 701 MULTIMEDIA 070497  
Download from Www.Somanuals.com. All Manuals Search And Download.  
APPENDIX B : ORBITING  
Orbitingspeedtoggle(onlyin MASTEROrbiting)  
Highlight 'SPEED : SLOW' with  
the coontrol disk and press EN-  
TER to set the ORBITING SPEED  
to Fast.  
Highlight 'SPEED : FAST' with the  
control disk and press ENTER to  
settheORBITINGSPEEDtoSlow  
M AST ER ORBI TING  
CHAN GE TO S LAVE  
MO DE : ON  
SPEED: FAST  
ADJUST DEVIATION  
SELECT WITH  
OR  
TH EN < ENTE R>  
DEVIATION ADJUST  
:
VERTICAL WITH  
HORIZONTAL WITH  
OR  
OR  
<EXIT> to return  
ENTER continues to Set up Orbiting.  
EXIT returns to the Path Selection menu.  
ADJUST returns to the Operational mode.  
Orbitingalignment  
Preparation :  
Before proceeding to the alignment of the Orbiting default settings, be sure that  
the Horizontal Phase and the Raster shift are correctly aligned with the Orbiting  
mode set to OFF.  
This alignment must be performed in case of a multiple projector installation with  
Master and Slave projectors in order to ensure a correct operation of the Orbiting  
for all projectors.  
Adjustmentprocedurestandaloneprojector:  
Highlight 'ADJUST DEVIATION'  
with the control disk and press  
ENTER.  
M AST ER ORBI TING  
CHAN GE TO S LAVE  
MO DE : ON  
SPEED: FAST  
ADJUST DEVIATION  
SELECT WITH  
OR  
TH EN < ENTE R>  
DEVIATION ADJUST  
:
VERTICAL WITH  
HORIZONTAL WITH  
OR  
OR  
<EXIT> to return  
R5975238 BARCOVISION 701 MULTIMEDIA 070497  
B-3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
APPENDIX B : ORBITING  
When adjusting the horizontal and the vertical deviation, the picture moves in the  
corresponding direction, allowing the set up of the deviation without orbiting  
operation.  
Push the control disk to the left  
(right) or up (down) to toggle be-  
tween Hor. and Vert. deviation  
adjustment.  
HORIZONTAL  
ORBIT AMPL  
7 0  
Adjust horizontal deviation by pushing  
the control disk to the left or to the right  
VERTICAL  
ORBIT AMPL  
Adjust vertical deviation by pushing  
7 0  
the control disk up or down  
ENTER will select the Orbiting adjustment  
menu.  
EXIT returns to the Path Selection menu.  
B-4  
R5975238 BARCOVISION 701 MULTIMEDIA 070497  
Download from Www.Somanuals.com. All Manuals Search And Download.  
APPENDIX B : ORBITING  
Adjustmentproceduremultipleprojectorinstallations:  
Important : to allow corrections in the deviation alignments of the slave projectors,  
never adjust the deviations of the master projector to its maximum.  
Default setting of the Master projector see 'Stand alone projector'.  
Highlight 'ADJUST DEVIATION'  
with the control disk and press  
ENTER.  
SLAVE ORBITING  
CHAN GE TO MA STER  
ADJUST DEVIATION  
When adjusting the horizontal and  
the vertical deviation, the picture  
SELECT WITH  
THE N <ENTER>  
OR  
moves in the corresponding direc-  
tion, allowing the set up of the  
deviation without orbiting opera-  
tion.  
DEVIATION ADJUST  
:
VERTICAL WITH  
HORIZONTAL WITH  
OR  
OR  
<EXIT> to return  
Push the control disk to the left  
(right) or up (down) to toggle be-  
tween Hor. and Vert. deviation  
adjustment.  
HORIZONTAL  
ORBIT AMPL  
7 0  
Adjust horizontal deviation by pushing  
the control disk to the left or to the right  
VERTICAL  
ORBIT AMPL  
Adjust vertical deviation by pushing  
the control disk up or down  
7 0  
ENTER will select the Orbiting Adjust-  
ment menu.  
EXIT returns to the Path Selection menu.  
R5975238 BARCOVISION 701 MULTIMEDIA 070497  
B-5  
Download from Www.Somanuals.com. All Manuals Search And Download.  
APPENDIX B : ORBITING  
B-6  
R5975238 BARCOVISION 701 MULTIMEDIA 070497  
Download from Www.Somanuals.com. All Manuals Search And Download.  
APPENDIX C : SOFT EDGE MATCHING  
Soft edge matching (option)  
Multi-screens are popular for many applications. In these installations, the goal is  
to obtain a contiguous matched image, forming one homogenous view. The soft  
edge matching feature provides a solution to the annoying side effects when  
adjustingtwoormoreprojectedimagesnexttoeachother. Toimprovethisjunction,  
both images must be overlapping within a certain percentage of the total screen  
width. During the overlapping period, both video signals are modulated by  
appropriatewaveformssothattheresultinglightoutputequalstherestoftheimage.  
Picture with hard edging  
Picture with overlapping  
Picture with soft edging  
R5975238 BARCOVISION 701 MULTIMEDIA 070497  
C-1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
APPENDIX C : SOFT EDGE MATCHING  
t o ta  
1 0 0 %  
l
lig h t  
o
u tp u t  
Basicconcept  
lig h t  
1 0 0 %  
o
u t p u t  
p
e
r
im  
a
g
e
5 0 %  
Im  
a
g
e
1
Im  
a
g
e
2
a
d
justa  
b
le  
o
ve rla  
p
p
ing  
a
re  
a
Adjustment procedure :  
StartuptheadjustmentmodebypressingADJUST(seealsochapter'Startupofthe  
adjustment mode')  
Highlight Random access with the control disk and press ENTER to start up the  
Random Access Adjustment mode (see also chapter Random Access Adjustment  
mode). The Random Access Adjustment Mode main menu will be displayed.  
When the Soft edge matching op-  
tion is installed, the projector auto-  
matically detects this option and  
displays the selection (activation)  
line in the Random Access Adjust-  
R AN DO M A CC ES S  
AD JUS TME NT MO DE  
PICTURE TUNING  
G EO M E TR Y  
CO NV ERG EN CE  
ment Mode main menu.  
COL OR SEL ECT  
COLO R BALA NCE  
ORBI TING  
Highlight SOFT EDGE with the  
control disk and press ENTER to  
CONTR . MODULA TION  
SOFT ED GE  
Select with  
<ENTER> to accept  
<EXIT> to return  
or  
select.  
The Soft Edge Correction menu  
offers the possibility to display a  
horizontal test pattern and a verti-  
cal test pattern. When the test  
patternsareON,the'real'softedge  
is disabled, marking lines for the  
start and stop position of soft edg-  
ing and the overlapping area are  
displayed. When the test patterns  
are OFF, the 'real' soft edge is  
enabled again.  
6 36 h  
ENTER displays the Soft Edge Matching  
menu.  
EXIT returns to the Path Selection menu.  
ADJUST returns to the Operational mode.  
Note : blanking corrections must  
be set to display a normal video  
image.  
C-2  
R5975238 BARCOVISION 701 MULTIMEDIA 070497  
Download from Www.Somanuals.com. All Manuals Search And Download.  
APPENDIX C : SOFT EDGE MATCHING  
Each overlap area (left and right) is determined by a start (stop) position and an area  
width.  
The start (stop) position for the top (bottom) overlap area is determined by the  
blanking adjustment.  
Highlight'HTESTMODE'andpress  
ENTER.  
SO FT ED GE  
CO RRE CTI ON  
The test image is enabled to adjust  
thestart(stop)positionandthearea  
S TA R T  
T O P  
width.  
S TA R T L EFT RIG HT STO P  
B O TT O M  
S T O P  
H
V
TES T MOD E-O FF  
TEST MO DE-O FF  
Select with  
or  
then <ENTER>  
<EXIT> to return  
639i  
ENTERtoggles between H test mode OFF  
and ON.  
EXIT returns to the Random Access Ad-  
justment Mode main menu.  
ADJUST returns to the Operational mode.  
Thetestimageisprojectedonthe  
normal image  
Left(width)  
Right(width)  
Start position  
Rast er  
Stop position  
I m a g e  
4 1 5  
Visible lines  
R5975238 BARCOVISION 701 MULTIMEDIA 070497  
C-3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
APPENDIX C : SOFT EDGE MATCHING  
Start position  
Highlight START POSITION with  
the control disk and press ENTER.  
SOF T ED GE  
COR RECT ION  
S TA R T  
T O P  
START LEFT RIGHT STOP  
B O TT O M  
S T O P  
H
V
TEST MODE-OFF  
TEST MODE-OFF  
Select with  
or  
then <ENTER>  
<EXIT> to return  
639a  
ENTER displays the normal image super-  
imposed with the internal generated test  
signal.  
EXIT returns to the Random Access Ad-  
justment Mode main menu.  
ADJUST returns to the Operational mode.  
Adjustthefirstleftlineofthegener-  
ated test image to determine the  
image border. This image border  
is the start position of the soft edge  
area.  
Left(width)  
Note : when the start position is not  
visible by the first image display,  
adjust with the control disk until the  
line becomes visible. Adjust then  
until the start position is correct.  
Start position  
4 1 5 a  
ENTER displays the Soft Edge menu.  
C-4  
R5975238 BARCOVISION 701 MULTIMEDIA 070497  
Download from Www.Somanuals.com. All Manuals Search And Download.  
APPENDIX C : SOFT EDGE MATCHING  
Left image area  
Highlight LEFT with the control  
disk and press ENTER.  
The normal image superimposed  
with the test pattern will be dis-  
played.  
SOF T ED GE  
COR RECT ION  
S TA R T  
T O P  
S TA R T LEFT RIGHT STOP  
B O TT O M  
S T O P  
H
V
TEST MODE-OFF  
TEST MODE-OFF  
Select with  
or  
then <ENTER>  
<EXIT> to return  
639d  
ENTER displays the normal image super-  
imposed with the internal generated test  
signal.  
EXIT returns to the Random Access Ad-  
justment Mode main menu.  
ADJUST returns to the Operational mode.  
Adjust the left soft edge area width  
by moving with the control disk the  
second test pattern line towards  
its desired position.  
Left(width)  
Start position  
4 1 5 a  
ENTER returns to the Soft Edge Correc-  
tion menu.  
R5975238 BARCOVISION 701 MULTIMEDIA 070497  
C-5  
Download from Www.Somanuals.com. All Manuals Search And Download.  
APPENDIX C : SOFT EDGE MATCHING  
Stop position  
Highlight STOP POSITION with  
the control disk and press ENTER.  
SOF T ED GE  
COR RECT ION  
S TA R T  
T O P  
S TA R T LEFT RIGHT S TO P  
B O T TO M  
S T O P  
H
V
TEST MODE-OFF  
TE ST MODE -OFF  
Select with  
or  
then <ENTER>  
<EXIT> to return  
639h  
ENTER displays the normal image super-  
imposed with the internal generated test  
signal.  
EXIT returns to the Random Access Ad-  
justment Mode main menu.  
ADJUST returns to the Operational mode.  
Adjust the last right line of the  
generated test image to deter-  
mine the image border. This im-  
age border is the end position of  
the right soft edge area.  
Right(width)  
Note : when the stop position is  
not visible by the first image dis-  
play, push the control disk until  
the line becomes visible. Adjust  
then until the stop position is cor-  
rect.  
Stop position  
4 1 5 b  
ENTER displays the Soft Edge menu.  
C-6  
R5975238 BARCOVISION 701 MULTIMEDIA 070497  
Download from Www.Somanuals.com. All Manuals Search And Download.  
APPENDIX C : SOFT EDGE MATCHING  
Right image area  
Highlight LEFT with the control  
disk and press ENTER.  
The normal image, superimposed  
with the test pattern will be dis-  
played.  
SO FT E DG E  
CO RR EC TI ON  
S TA R T  
T O P  
S TA R T L EFT R I G H T S TOP  
B O TT O M  
S T O P  
H
V
TES T MOD E-O FF  
TEST MO DE-O FF  
Select with  
or  
then <ENTER>  
<EXIT> to return  
639e  
ENTER displays the normal image super-  
imposed with the internal generated test  
signal.  
EXIT returns to the Random Access Ad-  
justment Mode main menu.  
ADJUST returns to the Operational mode.  
Use the control disk to adjust the  
right soft edge area width by mov-  
ing the second test pattern line  
towards its desired position.  
Right(width)  
Stop position  
4 1 5 b  
ENTER returns to the Soft Edge Correc-  
tion menu.  
R5975238 BARCOVISION 701 MULTIMEDIA 070497  
C-7  
Download from Www.Somanuals.com. All Manuals Search And Download.  
APPENDIX C : SOFT EDGE MATCHING  
Vertical test mode  
Highlight 'V TEST MODE' and  
press ENTER.  
The test image is enabled to adjust  
the start (stop) position and the  
area width.  
When switching the V test mode to  
On, the H test mode will switch to  
OFF.  
SOF T ED GE  
COR RECT ION  
S TA R T  
T O P  
S TA R T LEFT RIGHT S TO P  
B O TT O M  
S T O P  
TEST MODE-OFF  
TEST MODE-OFF  
H
V
Select with  
or  
then <ENTER>  
<EXIT> to return  
639j  
ENTER toggles between V test mode OFF  
and ON.  
EXIT returns to the Random Access Ad-  
justment Mode main menu.  
ADJUST returns to the Operational mode.  
Top Blanki ng  
Top(width)  
The test image is projected on the  
normal image. The start (stop)  
positionisdeterminedbytheblank-  
ing controls. The blanking adjust-  
ment is also the image border for  
the begin (end) position of the soft  
edge area. Adjust the blanking for  
a normal video image.  
Bottom(width)  
4 1 6  
Bottom blanking  
Ras ter  
I m a g e  
Visible lines  
C-8  
R5975238 BARCOVISION 701 MULTIMEDIA 070497  
Download from Www.Somanuals.com. All Manuals Search And Download.  
APPENDIX C : SOFT EDGE MATCHING  
Top soft edge area adjustment  
Highlight TOPwiththecontroldisk  
and press ENTER.  
The normal image, superimposed  
with the test pattern will be dis-  
played.  
SO FT ED GE  
CO RRE CTI ON  
S TA R T  
T O P  
START LEFT RIGHT STOP  
B O TT O M  
S T O P  
H
V
TES T MOD E-O FF  
TEST MO DE-O FF  
Select with  
or  
then <ENTER>  
<EXIT> to return  
639b  
ENTER displays the normal image super-  
imposed with the internal generated test  
signal.  
EXIT returns to the Random Access Ad-  
justment Mode main menu.  
ADJUST returns to the Operational mode.  
Top Blanking  
Top(width)  
Adjust the top soft edge area width  
by changing the length of the inter-  
nalgeneratedlineswiththecontrol  
disk.  
4 1 6 a  
ENTER returns to the Soft Edge Correc-  
tion menu.  
R5975238 BARCOVISION 701 MULTIMEDIA 070497  
C-9  
Download from Www.Somanuals.com. All Manuals Search And Download.  
APPENDIX C : SOFT EDGE MATCHING  
Bottom soft edge area adjustment  
Highlight BOTTOM with the con-  
trol disk and press ENTER.  
Thenormalimage, superimposed  
with the test pattern will be dis-  
played.  
SOF T ED GE  
COR RECT ION  
S TA R T  
T O P  
S TA R T LEFT RIGHT S TO P  
B O T TO M  
S T O P  
H
V
TEST MODE-OFF  
TE ST MODE -OFF  
Select with  
or  
then <ENTER>  
<EXIT> to return  
639g  
ENTER displays the normal image super-  
imposed with the internal generated test  
signal.  
EXIT returns to the Random Access Adjust-  
ment Mode main menu.  
ADJUST returns to the Operational mode.  
Adjust the bottom soft edge area  
width by changing the length of the  
internal generated lines with the  
control disk.  
Bottom(width)  
4 1 6 b  
Bottom blanking  
ENTER returns to the Soft Edge Correction  
menu.  
C-10  
R5975238 BARCOVISION 701 MULTIMEDIA 070497  
Download from Www.Somanuals.com. All Manuals Search And Download.  
APPENDIX D : CONTRAST MODULATION  
Contrastmodulation(option)  
Today multi-screens are very popular for many applications e.g. simulation busi-  
ness. In these installations, the goal is to obtain a continuous matched image,  
forming one homogeneous view. The viewer wants to see an overall light output  
uniformity.  
The laws of physics applied to projection optics dictate that the center of the  
projected image will be brighter than the corners; this phenomenon is normally  
referred to as 'corner fall off'. Secondly, due to the normal off-axis projection of the  
red and blue images, CRT projection displays a phenomenon referred to as 'color  
shift', whereby one side of the screen is reddish an the other blueish.  
Picture without  
contrast modulation  
Picture with  
contrast modulation  
R5975238 BARCOVISION 701 MULTIMEDIA 070497  
D-1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
APPENDIX D : CONTRAST MODULATION  
WITH C O NTRAST MO DULATIO N  
WITHO UT C O NTRAST MO DULATIO N  
Basicconcept  
h
o
rizo  
n
t a  
l
lig  
h
t
o u t p u t  
h
o
rizo  
n
t a  
l
lig  
h
t
o
u t p u t  
C O RN ER  
FA LL O FF  
C O RNER  
FA LL O FF  
1 0 0 %  
5 0 %  
1 0 0 %  
5 0 %  
Im  
a
g
e
Im  
o
a
g
e
v e rtic  
a
l
v e rtic  
a
l
lig o u t p  
h
t
u
t
1 0 0 %  
5 0 %  
1 0 0 %  
lig  
h
t
o u t p  
u
t
5 0 %  
h
o
rizo  
n
t a  
l
lig  
h
t
o
u p t u t  
h
o
rizo n t a  
l
lig  
h
t
u
p
t u t  
1 0 0 %  
1 0 0 %  
7 5 %  
C
O
LO  
R
C
O
LO  
R
g
re e  
n
5 0 %  
r e  
d
b
lu  
e
5 0 %  
SHIFT  
SHIFT  
g
re e  
n
r e  
b
d
lu  
e
Im  
a
g
e
Im  
a
g
e
v e rtic  
a
l
v e rtic  
a
l
5 0 % 1 0 0 %  
7 5 %  
lig  
h
t
o u t p  
u
t
lig o u t p  
h
t
u
t
5 0 %1 0 0 %  
Adjustment procedure :  
Start up the adjustment mode by pressing ADJUST (see also chapter 'Start up of the  
adjustment mode')  
Highlight Random Access with the control disk and press ENTER to start up the  
Random Access Adjustment mode  
(see also chapter Random Access  
Adjustment mode). The Random  
Access Adjustment Mode main  
R AN DO M A CC ES S  
AD JUS TME NT MO DE  
menu will be displayed.  
When the Contrast Modulation op-  
tion is installed, the projector auto-  
matically detects this option and  
PICTURE TUNING  
G EO M E TR Y  
CO NV ERG EN CE  
COL OR SEL ECT  
COLO R BALA NCE  
ORBI TING  
CONTR . MODULA TION  
displays the selection (activation)  
SOFT ED GE  
line in the Random Access Adjust-  
ment Mode main menu.  
Select with  
<ENTER> to accept  
<EXIT> to return  
or  
Highlight CONTR. MODULATION  
with the control disk and press EN-  
TER to select.  
6 36 g  
Note : An external generated white  
image will be useful during the ad-  
justment.  
ENTER selects the Contrast Modulation  
menu.  
EXIT returns to the Path Selection menu.  
ADJUSTreturnstotheOperationalmode.  
Note : be sure the horizontal phase  
is correctly adjusted. The image  
must be centered on the raster with  
the horizontal phase adjustment,  
otherwiseitisnotpossibletoadjust  
the contrast modulation correctly.  
D-2  
R5975238 BARCOVISION 701 MULTIMEDIA 070497  
Download from Www.Somanuals.com. All Manuals Search And Download.  
APPENDIX D : CONTRAST MODULATION  
The first 3 adjustments (horizontal  
red, green and blue) are used for  
horizontal light equalisation for the  
three specific colors separately.  
This compensates the error due to  
the different horizontal position of  
the picture tubes. One side of the  
image is reddish and the other side  
is blueish. This phenomenon is  
called Color shift.  
C ON T R AS T  
EQ UALI SATI ON  
RED HOR IZON TAL  
GR EEN HORI ZONTAL  
BLU E HOR IZON TAL  
VE RTIC AL  
C ON T R AS T  
ED GE C ORR ECTI ON  
LE FT-RIG HT  
TO P- B O TTO M  
Select with  
or  
then <ENTER>  
<EXIT> to return  
TheVERTICALadjustmentaffects  
the three colors at the same time  
and corrects the vertical error in  
light output due to the projection  
angle (10.5 degrees).  
338  
Left-right (horizontally) and top-  
bottom (vertically) adjustments  
improve the 'hotspot' in the center  
of the screen.  
Contrastequalisation('ColorShift')  
Highlight RED HORIZONTAL with  
the control disk and press ENTER.  
Onlyaredimageisdisplayed. Use  
thecontroldisktoequalisethelight  
output on the left and right side of  
the image. The best result is ob-  
tained on a white image by looking  
on the left and the right side until  
both or equal, or by using a very  
sensitive light meter.  
CO NT RA ST  
EQUALISATION  
RED HORIZONTAL  
GREEN HORIZONTAL  
BLUE HORIZONTAL  
VERTICAL  
CO NTRA ST  
EDGE CORRECTION  
LEFT-RI GHT  
TOP -B OTTO M  
Select with  
or  
then <ENTER>  
<EXIT> to return  
ENTER returns to the Contrast  
Modulation menu.  
338a  
Repeat this adjustment for green  
and blue by selecting first Green  
horizontal and then Blue horizon-  
tal.  
ENTER displays the red image.  
EXIT returns to the Random Access Ad-  
justment Mode main menu  
Remark : When the end of adjust-  
ment range is reached for red and  
blue, the green image will be dis-  
played too, to give you the mes-  
sage 'end of adjustment range'.  
The green image remains active  
until a new selection is made.  
ADJUSTreturnstotheOperationalmode.  
R5975238 BARCOVISION 701 MULTIMEDIA 070497  
D-3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
APPENDIX D : CONTRAST MODULATION  
Highlight VERTICAL with the con-  
trol disk and press ENTER. This  
adjustment is done for all three  
colors at the same time.  
C ON T R AS T  
EQ UALI SATI ON  
RED HOR IZON TAL  
GR EEN HORI ZONTAL  
BLU E HOR IZON TAL  
VE RTIC AL  
Use the control disk to equalise the  
vertical light output and press EN-  
TER to continue.  
C ON T R AS T  
ED GE C ORR ECTI ON  
LE FT-RIG HT  
TO P- B O TTO M  
Select with  
then <ENTER>  
or  
The best result is obtained on a  
white image by looking on the top  
and the bottom side until both are  
equal, or by using a very sensitive  
light meter.  
<EXIT> to return  
338d  
ENTERselectstheVerticalContrastEquali-  
sation option.  
EXIT returns to the Random Access Ad-  
justment Mode main menu.  
ADJUST returns to the Operational mode.  
Contrast edge correction ('hot spot')  
Highlight LEFT-RIGHT with the  
control disk and press ENTER to  
start the horizontal 'hot spot' cor-  
rection in the center of the screen.  
Adjust with the control disk for the  
same light output in the corners as  
in the center of the image.  
C ON T R AS T  
EQ UALI SATI ON  
RED HOR IZON TAL  
GR EEN HORI ZONTAL  
BLU E HOR IZON TAL  
VE RTIC AL  
C ON T R AS T  
ED GE C ORR ECTI ON  
LE FT-RIG HT  
TO P- B O TTO M  
This left-right adjustment must be  
done in combination with the top-  
bottom adjustment as both adjust-  
ments influence each other.  
Select with  
or  
then <ENTER>  
<EXIT> to return  
338a  
Note : these adjustments will re-  
duce the total light output, so do  
not over adjust.  
Hint : A bar scale of 10 - 15 for both  
adjustments gives a good result.  
ENTERstartstheLeft-RightContrastEdge  
Correction.  
EXIT returns to the Random Access Ad-  
justment main menu.  
ADJUST returns to the Operational mode.  
Press ENTERtoreturntotheCon-  
trast Modulation menu.  
D-4  
R5975238 BARCOVISION 701 MULTIMEDIA 070497  
Download from Www.Somanuals.com. All Manuals Search And Download.  
APPENDIX D : CONTRAST MODULATION  
Highlight TOP-BOTTOM with the  
control disk and press ENTER to  
start the vertical 'hot spot' cor-  
rection in the center of the  
screen. Adjust with the control  
disk for the same light output in  
the corners as in the center of  
the image.  
CO NT RA ST  
EQUALISATION  
RED HORIZONTAL  
GREEN HORIZONTAL  
BLUE HORIZONTAL  
VERTICAL  
CO NTRA ST  
EDGE CORRECTION  
LEFT-RI GHT  
TOP -B OTTO M  
Select with  
or  
then <ENTER>  
This top-bottom adjustment must  
be done in combination with the  
left-right adjustments as both ad-  
justments influence each other.  
<EXIT> to return  
338f  
Note : these adjustments will re-  
duce the total light output, so do  
not over adjust.  
Hint : A bar scale of 10 - 15 for  
both adjustments gives a good  
result.  
ENTER starts the Top-Bottom Contrast  
Edge Correction.  
EXIT returns to the Random Access Ad-  
justment Mode main menu.  
ADJUST returns to the Operational mode.  
Press ENTER to return to the  
Contrast Modulation menu.  
R5975238 BARCOVISION 701 MULTIMEDIA 070497  
D-5  
Download from Www.Somanuals.com. All Manuals Search And Download.  
APPENDIX D : CONTRAST MODULATION  
D-6  
R5975238 BARCOVISION 701 MULTIMEDIA 070497  
Download from Www.Somanuals.com. All Manuals Search And Download.  
APPENDIX E : ADJUSTMENT BLOCKS  
Adjustment Blocks (memory blocks)  
As the BARCOVISION 701 MULTIMEDIA is digitally controlled, all geometry and  
convergence adjustments are stored in the projector’s memory as numeric  
values. These numeric values are used to control digital potentiometers which  
in turn, control the projector. Each source connected to the projector has a  
unique set of adjustment data which is automatically downloaded into the  
projector’s digital potentiometers as the source is selected. This set of  
adjustment data is referred to as an “adjustment block”.  
An adjustment table is automatically created for a source when the source is first  
connected to the projector and the adjust mode is entered. If other sources have  
alreadybeenconnectedtotheprojectorandgeometryandconvergenceadjustments  
have been performed on these sources, the projector will use Linear Digital Interpo-  
lation to create a new block for the new source. This block will provide an initial set  
of adjustments for the new source that have been calculated by the projector from  
“previousexperience”.  
The projector’s memory has the capacity to store 32 adjustment blocks. The  
adjustment block consists of two parts, the block header and the data representing  
the convergence and geometry adjustments of the source the block corresponds  
to. The block header contains the basic characteristics of the source and the  
projector configuration used to display the source.  
Block Header  
example of block header  
Block number  
01  
Source number  
01  
Horizontalfrequency  
Verticalfrequency  
Inputtype  
15.6 kHz  
50 Hz  
video  
Scan inversion switch configuration  
front/ceiling  
The data representing the geometry and convergence adjustments for the source  
follows the block header.  
The 32 adjustment blocks are in use. What to do?  
A. Projector without any peripheral connected to the 'peripheral  
800 port'  
Connect a new source to the projector. Due to the fact that there are no adjustment  
E-1  
R5975238 BARCOVISION 701 MULTIMEDIA 070497  
Download from Www.Somanuals.com. All Manuals Search And Download.  
APPENDIX E : ADJUSTMENT BLOCKS  
blocks available, the projector dis-  
plays a warning.  
W A RN I N G  
All memory blocks are  
use d.  
Please, go to t he  
Press ENTER to continue and start  
up the adjustment mode to delete a  
block.  
It will be necessary to delete an  
existing block to create adjustment  
space for the new source.  
service mode, delete  
block and reselect the source  
or return t o an  
a
existing source.  
AT T ENT I O N  
Any adjust ment will  
corrupt he latest used  
block.  
<ENTER> to continue  
When ENTER is pressed, the warning disappears. Press ADJUST to start up the  
'adjustment mode' and select 'Service' with the arrow keys.  
Follow the procedure as described in 'Deletion of blocks'.  
Reselect the new source with the numeric keys on the RCU or the local keypad  
even when the new source is already displayed on the screen.  
By reselecting this new source, you force the projector to write the source header  
in the free space created by the previous deletion action. The new source can  
now be adjusted, the settings will be stored for future use.  
Attention :  
When the warning is displayed by pressing ENTER, you will see the normal  
image. Do not forget to start the 'deletion of a block' procedure, otherwise the  
image settings of the last selected source will be overwritten with the new  
adjustments.  
B. projector equipped with RCVDS or VS05.  
When a new source is connected :  
a) the projector looks for the most corresponding adjustment block. If such a  
block is present, the settings will be used to display the connected source.  
b) the projector does not find a matching block. The warning is displayed. Follow  
the procedure as in A.  
R5975238 BARCOVISION 701 MULTIMEDIA 070497  
E-2  
Download from Www.Somanuals.com. All Manuals Search And Download.  
APPENDIX F : SOURCE NUMBERS 90 - 99  
Source numbers 90 - 99  
Source numbers 90 - 99 do not correspond to physical inputs to the projector or  
RCVDS05. Theyareusedtoassignanadditionaladjustmentblocktoasource. This  
additional adjustment block may contain different geometry and convergence set-  
tings, sync fast/slow positions and enhanced blue on/off settings. The relationship  
between source numbers 0 - 9 and 90 - 99 (projector with RCVDS) or 1 - 5 and 91  
- 95 (stand-alone projector) is shown in the diagram below.  
source number 0  
source number 90  
Block header A  
source input 0  
Block header A, different  
analogsettings  
source number 1  
source number 91  
Block header B  
source input 1  
source input 2  
Block header B, different  
analogsettings  
Block header C  
source number 2  
source number 92  
Block header C, different  
analogsettings  
source number 9  
source number 99  
Block header J  
source input 9  
Block header J, different  
analogsettings  
The alternate adjustment block for sources 0 - 9 (projector with RCVDS) or 1 - 5  
(stand-alone projector) is activated by selecting the corresponding source number  
0 - 9 (projector with RCVDS) or 1 - 5 (stand-alone projector). Once this source  
number is selected, the alternate block of adjustment data is in use and may be  
modified via the adjust mode of the projector. The alternate adjustment block is  
automatically stored.  
R5975238 BARCOVISION 701 MULTIMEDIA 070497  
F-1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
APPENDIX F : SOURCE NUMBERS 90 - 99  
Follow the steps below to create a second adjustment block for a source between 0  
and 9.  
1. Select the source between 0 and 9 that the second adjustment block is to be  
created for.  
2. Select the corresponding source number between 90 and 99. The adjustment  
block for the source number between 0 and 9 is copied to the corresponding  
source number between 90 and 99.  
3. Enter the adjust mode and make any desired changes (geometry, convergence,  
sync fast/slow, enhanced blue on/off) to the second adjustment block.  
4. Exit the adjust mode.  
Note : the above also applies to source number 1 - 5 and 91 - 95 of a stand alone  
projector (no RCVDS).  
F-2  
R5975238 BARCOVISION 701 MULTIMEDIA 070497  
Download from Www.Somanuals.com. All Manuals Search And Download.  
RC U  
RC U  
INPUT SOURCES  
PROJECTOR  
1
INPUT SOURCES  
PROJECTOR  
1
2
3
4
5
6
7
P
P
2
3
4
5
6
7
INPUT SOURCES  
R C V D S  
INPUT SOURCES  
R C V D S  
1
2
1
2
3
3
5
5
6
6
7
7
8
8
9
9
10  
10  
R5975238 BARCOVISION 701 MULTIMEDIA 070497  
i-1  
Download from Www.Somanuals.com. All Manuals Search And Download.  

3Com Home Theater System 3C18320 User Manual
AEG Coffeemaker Coffee Machines User Manual
AKG Acoustics Microphone C 3000 User Manual
AKG Acoustics Microphone CK 91 User Manual
American Audio CD Player DCD PRO240 User Manual
American Standard Plumbing Product M968641 User Manual
ATON Speaker A60W User Manual
Ayre Acoustics Stereo System C 5XEMP User Manual
BC Speakers Speaker 10PS26 User Manual
Beko Cooktop QHMW6422 User Manual