Baby Trend Baby Playpen PY90973 User Manual

Read all instructions BEFORE assembly and USE of product.  
KEEP INSTRUCTIONS FOR FUTURE USE.  
Item#: PY90973  
Check that you have all the below parts for this model  
before assembling the playard.  
Nursery Center  
Close N Cozy (Type C)  
Soft Goods x 1  
Strap Set x 1  
Playard (fully assemble) x 1  
Mattress x 1  
Changing Table x 1  
Mattress Support Bar x 2  
Lower Bar x 2  
Long Curved Bar x 2  
Short Bar with Connector Knob x 2  
Music Center x 1  
Center Cross Bar x 1  
Upper Back Bar x 1  
Upper frame x 2  
Side frame x 2  
Leg x 4  
Screw x 4  
---------------------------------------------  
Travel / Storage Bag x 1  
Mini Playard  
This unit does not equipped with basket, bassinet, mobile,  
parent organizer and canopy.  
IF YOU EXPERIENCE ANY DIFFICULTY IN USING THIS PRODUCT,  
PLEASE CONTACT OUR CUSTOMER SERVICE DEPARTMENT AT  
1-800-328-7363 BETWEEN THE HOURS OF 8:00 A.M. AND 4:30 P.M. PACIFIC  
STANDARD TIME FOR ASSISTANCE. PLEASE HAVE YOUR MODEL NUMBER AND  
MANUFACTURING DATE AVAILABLE WHEN YOU CALL. THIS INFORMATION CAN BE  
FOUND ON A SMALL STICKER UNDER THE PLAYARD.  
Instruction Manual  
Convenience through innovation and thoughtful design  
04.09  
Contact us by mail:  
Baby Trend, Inc.  
1607 S. Campus Ave., Ontario, CA 91761  
Contact us by phone:  
1-800-328-7363 (8:00am ~ 4:30pm PST)  
Convenience through innovation and thoughtful design  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PARTS  
ASSEMBLY  
TO ASSEMBLE PLAYARD  
IMPORTANT!To ensure safe operation of your playard,  
please follow these instructions carefully. Please keep these  
instructions for future reference.  
IMPORTANT! Before assembly and each use, inspect this  
product for damaged hardware, loose joints, missing parts or sharp  
edges. NEVER use if any parts are mssing or broken.  
IMPORTANT!Adult assembly is required.  
Mattress  
Playard  
This model may not include some features shown below. Check the parts list to make sure  
you have all the parts for this model before assembling the playard.  
ATTENTION:  
Playard must be fully assembled and securely  
locked before installing or using other accessories.  
1. Unzip bag and remove Playard frame (Fig. 1).  
Undo the three (3) Fasten straps and set the  
Mattress aside (Fig. 2).  
Fig. 1  
2. Turn the Playard right side up and keep the  
Legs and Wheels close together. Stretch out  
top of Playard and pull up one side at a time of  
each of the top rails until each latch “Clicks”  
and locks securely into place (Fig. 3).  
Metal Support Tubes  
(2 male, 2 female)  
Bassinet  
Playard  
NOTE: The best way to lock the rail(s) is to  
hold one hand on each side and pull up sharply.  
(DO NOT pull from the middle where the latch  
release is located).  
Fig. 2  
Long Curved Bar (2)  
IMPORTANT: The handle located in the center  
of the Playard floor MUST remain raised  
(Approx. 45.7 cm or 18 inches) while locking  
the side rails in place. If the center is not raised  
the rails will NOT lock.  
Short Bar with Connector  
Knob (2)  
Changing Table  
Mattress  
If you experience difficulty and one side of the  
rail will lock but the other side will not then,  
unlock the rail by squeezing the release in the  
center and try again. If you still have difficulty,  
contact our Customer Service Center at  
1-800-328-7363 or visit us online at  
Fig. 3  
sleep play nature  
mp3  
input  
Fixed Mobile  
Music Center  
Travel / Storage Bag  
Parent Organizer*  
Fig. 4  
* Type may vary  
Copyright © 2007 - 2009, Baby Trend Inc., All Rights Reserved.  
Copyright © 2007 - 2009, Baby Trend Inc., All Rights Reserved.  
3
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
ASSEMBLY  
ASSEMBLY  
3. To operate the brakes on the Wheels, press  
downward on the brake levers. To release, lift  
upward on the lever (Fig. 4)  
FOLDING PLAYARD  
1. Undo the three (3) hooks and loop straps  
holding the Mattress from underneath the  
Playard floor or remove the Mattress for the  
Bassinet and set aside.  
4. Once all four (4) top rails are locked in place,  
push down on the center handle (Fig. 5). The  
center mechanism will rotate clockwise 90  
degrees and automatically lock in place.  
Rotate before  
lifting  
2. Grasp the center handle, push down and rotate  
the handle counter-clockwise 90 degrees and  
lift upward until the handle is as high as the top  
rails (Fig. 10). Gather the Legs and Wheels  
together towards the center as close as possible  
so that they nearly touch (Fig. 11).  
Fig. 10  
Fig. 5  
IMPORTANT: Test each top rail by pushing  
down slightly to confirm each is rigid and  
locked securely in place before use (Fig. 6).  
NOTE: The top rails of the Playard are sill in  
the “Locked” position.  
ATTENTION:  
To use as a bassinet, skip to page 8 for bassinet  
installation instructions.  
Fig. 11  
3. Locate the rail release lever in the center and  
bottom side of each rail. Lift slightly while  
squeezing the lever until the rail “Clicks” and  
releases. Push down each side of the rail while  
still holding the release lever until both sides  
are down. Repeat for all remaining sides  
(Fig. 12).  
Fig. 6  
NOTE: If the top rail(s) do not release  
completely, DO NOT FORCE! Check the  
floor of the Playard to make sure all the bottom  
rails are unlocked and make sure the middle  
handle is pulled up and has not fallen back  
down. If so, repeat step #3.  
Fig. 12  
5. Place the Mattress on the floor of the Playard  
with the padded side facing up (Fig. 7)  
Fig. 7  
4. Gather four (4) corners and center all together  
tightly (Fig. 13).  
5. Wrap Mattress around Playard frame with  
padded side facing inward.  
Fig. 13  
6. Feed the three (3) hook and loop straps located  
on the underside of the Mattress through the  
slots in the floor of each end of the Playard  
(Fig. 8). Fasten the hook and loop straps to the  
underside of the Playard floor to prevent the  
Mattress from moving (Fig. 9).  
6. Secure the three (3) hook and loop straps by  
feeding them through the loops on the end  
of the Mattress and folding them back onto  
themselves (Fig. 14).  
Fig. 8  
7. Place folded Playard into carry bag so that the  
handle comes through the opening between  
each side of the zipper.  
Fig. 9  
Fig. 14  
Copyright © 2007 - 2009, Baby Trend Inc., All Rights Reserved.  
Copyright © 2007 - 2009, Baby Trend Inc., All Rights Reserved.  
5
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
WARNING  
ASSEMBLY  
ACCESSORIES  
TO ASSEMBLE BASSINET  
WARNING:Failure to follow these warnings and the  
instructions could result in serious injury or death.  
FALL HAZARD:To help prevent falls, do not use this  
product when the infant begins to push up on hands and knees or  
has reached the height of 25 in. (635 mm), weight of 15 lbs. (6.8 kgs)  
or 4 months old, whichever comes first.  
Metal Support Tubes  
(2 male, 2 female)  
Bassinet  
SUFFOCATION HAZARD:Infants can suffocate  
• In gaps between an extra pad and sides of the bassinet/cradle  
• On soft bedding  
Never add a mattress, pillow, comforter, or padding.  
Use only the pad provided by manufacturer.  
Never use a water mattress with this product.  
ATTENTION:  
Playard must be fully assembled and securely  
locked before installing or using the bassinet  
feature. (See To Assemble Playard section)  
You will need to remove the mattress from the  
bottom of the Playard to use inside your Bassinet.  
To reduce the risk of SIDS, pediatricians recommend healthy infants be  
placed on their back to sleep, unless otherwise advised by your physician.  
• The playard, including side rails, must be fully erected prior to use. Make  
sure each latch is secure.  
• Strings can cause strangulation! NEVER place items with a string around  
a child's neck such as hood strings or pacifier cords. NEVER suspend  
strings over bassinet or attach strings to toys.  
• Discontinue use of the bassinet or the changing table when child begins to  
push up on hands and knees or has reached the height of 25 in. (635 mm),  
weight of 15 lbs. (6.8 kgs) or 4 months old, whichever comes first.  
1. Position the Bassinet over and down into the  
fully assembled Playard. Secure in place by  
pushing down firmly on each plastic support  
clip until all are snapped into place (Fig. 15).  
Fig. 15  
Fig. 16  
2. Assemble Mattress Support Tubes (if  
equipped; otherwise, skip to step 4) by  
inserting the two (2) male tubes into the two  
(2) female tubes (Fig. 16).  
NEVER place product near a window where cords from blinds or drapes  
can strangle a child.  
• Always provide the supervision necessary for the continued safety of your  
child. NEVER leave child unattended.  
3. Insert both, assembled, Mattress Support  
Tubes into the loops provided on the bottom  
of the Bassinet (Fig. 17).  
NEVER use plastic shipping bags or other plastic film as mattress covers  
not sold and intended for that purpose. They can cause suffocation.  
4. Place the Mattress into the Bassinet with the  
padded side facing upward (Fig. 18)  
• Use bassinet with only one child at at time.  
NEVER place a child under the bassinet.  
NEVER store the bassinet in the playard while in use.  
• The bassinet must be fully assembled and installed before using.  
Fig. 17  
NOTE: Fasten tabs underneath the Mattress  
secure it in place.  
STRANGULATION HAZARD: NEVER leave the changing table  
in place when the child is in the bassinet or the playard. Always flip  
changing table down while not in use.  
• To prevent your child from falls and other injuries, always use safety belt  
when child is on the changing table, always stay within arm's reach of  
your child when using the changing table.  
• To help prevent heat build-up inside the playard and to avoid overheating  
your child, when using the bassinet NEVER use an outdoor canopy.  
Copyright © 2007 - 2009, Baby Trend Inc., All Rights Reserved.  
TO REMOVE BASSINET  
1. Remove Mattress from Bassinet.  
2. Remove Canopy.  
3. Unsnap all clips and lift Bassinet.  
Fig. 18  
Copyright © 2007 - 2009, Baby Trend Inc., All Rights Reserved.  
7
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
ASSEMBLY  
ASSEMBLY  
MOBILE ASSEMBLY (Fixed)  
TO ASSEMBLE CHANGING TABLE  
ATTENTION: DO NOT attach Mobile to Canopy until Canopy is correctly installed  
as noted in the Canopy instructions.  
A crib mobile is intened for visual stimulation and is not intended to be grasped by the child.  
If attached to the crib or playpen, remove when baby begins to push up on hands and  
knees. If so designed, mount on wall or ceiling clearly out of a standing baby's reach.  
Always attach all provided fasteners (strings, straps, clamps, etc.) tightly to a crib or  
playpen according to the instructions. Check frequently.  
(a)  
(b)  
DO NOT add additional strings and straps to attach to a crib or playpen.  
DO NOT attach the Mobile with child in Playard or Bassinet.  
DO NOT remove the Mobile before retracting the Canopy or removing the Canopy.  
(c)  
WARNING  
Fixed Mobile  
FALL HAZARD: To  
prevent death or serious injury,  
always keep child within arm's  
reach.  
(c)  
Fig. 23  
(a)  
Always use restraint belt to prevent  
falls, see page 15 for details.  
(e)  
(d)  
(b)  
Contents:  
(a) 2 Long Curved Bars  
(b) 2 Short Bar with Connector Knobs  
(c) 1 Changing Table  
Contents:  
(a) 1 Mobile Lower Arm  
(b) 1 Mobile Arm Holder  
(c) 1 Mobile Upper Curved Arm  
(d) 1 Mobile Tri-shaped Arm  
(e) 3 Toys (toys may vary)  
(c)  
(a)  
(b)  
(a)  
(b)  
ATTENTION:  
Fig. 24  
Playard must be fully assembled and securely  
locked before installing or using the changing  
table feature. (See To Assemble Playard section)  
Fig. 19  
1. Insert the Mobile Lower Arm (a) into the  
Mobile Arm Holder (b) untill locked together  
(Fig. 19).  
Fig. 20  
(d)  
1. Connect the two (2) Long Curved Bars  
together (Fig. 23).  
2. Insert the Mobile Upper Curved Arm (c) into  
the Mobile Lower Arm (a, b) until locked  
together (Fig. 20).  
2. Insert the assembled curved bars into the  
Changing Table fabric (Fig. 24) Slide the  
Curved Bars around inside sleeve of the  
Changing Table.  
(e)  
Fig. 25  
Fig. 21  
3. Snap the Mobile Tri-shaped Arm (d) onto the  
end of the Upper Curved Arm (a, b, c)  
(Fig. 21). Connect each of the three Toys (e)  
to the Mobile by threading the string into the  
slot at the end of each arm.  
3. Connect the two (2) Short Bars to each end  
of the Long Curved Bar (Fig. 25) Make sure  
that the knobs are both facing down and the  
same direction on each end. (Fig. 26)  
4. Insert the bottom of the Mobile Arm into the  
frame of the Playard (Fig. 22).  
Fig. 26  
Fig. 22  
Copyright © 2007 - 2009, Baby Trend Inc., All Rights Reserved.  
Copyright © 2007 - 2009, Baby Trend Inc., All Rights Reserved.  
9
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ASSEMBLY  
ASSEMBLY  
4. Insert Connector Knob Prongs into holes  
located on both corners of the Playard  
(Fig. 27).  
To remove changing table  
Flip Changing Table to the outside of the Playard.  
Unsnap fabric flap of Changing Table from  
Playard. Twist Connector Knobs clockwise to  
unlock. (Fig. 33) Remove Changing Table from  
Playard (Fig. 34) and disconnect the Short Bars  
from the Curved Bar by pressing on the snap  
buttons and pulling apart. Remove Curved Bar  
from Changing Table sleeve.  
Fig. 27  
Fig. 33  
5. Turn the Connector Knobs counter clockwise  
to lock into place (Fig. 28).  
Fig. 28  
Fig. 34  
6. Flip Changing Table over onto Playard  
(Fig. 29).  
PARENT ORGANIZER ASSEMBLY  
7. Snap the two (2) buttons on the flap down  
onto the Playard (Fig. 30.  
Fig. 29  
or  
Parent Organizer  
Diaper Stacker  
IMPORTANT: Check that the Changing Table  
is correctly and securely installed BEFORE  
each use.  
1. Parent Organizer: Position each hook so that  
the hooked end is facing the rear side of the  
organizer. Press the hook down firmly into the  
slot until it snaps into place. (Fig. 35)  
Fig. 30  
To use changing table  
restraint system  
Diaper Stacker: Skip to step 2.  
2. Connect the Parent Organizer/Diaper  
Stacker to the Playard by sliding the two (2)  
connecting clips over an open portion of the  
top rail of the Playard. (Fig. 36)  
1. Place child on changing table, make sure hand  
and arms are clear of the restraint. Bring the  
restraint around the child's waist and clip the male  
and female ends of the buckle together. (Fig. 31)  
Fig. 35  
Fig. 31  
2. Tighten strap until fits snug around child's  
waist. DO NOT OVER TIGHTEN. (Fig. 32)  
NOTE: The Parent Organizer/Diaper Stacker  
can only be installed on open sides of the  
Playard where the connecting clips can easily  
be attached without interfering with other  
features.  
3. To remove, unsnap the buckle.  
ATTENTION:  
NEVER use changing table if it is damaged or  
broken.  
Fig. 32  
Fig. 36  
Copyright © 2007 - 2009, Baby Trend Inc., All Rights Reserved.  
Copyright © 2007 - 2009, Baby Trend Inc., All Rights Reserved.  
15  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ASSEMBLY  
ASSEMBLY  
Recording Indicator  
To listen to NATURE sounds, press the  
NATURE button you may use the previous /  
next button to change the sound. The Vol  
WARNING: Keep batteries out of children's reach. Old and  
new batteries should not be mixed. Alkaline, standard carbon-zinc, and  
rechargeable nickel-cadium batteries should not be mixed. Remove  
batteries before storing music center for a long period of time.  
or Vol  
buttons control the unit's volume.  
VIBRATION: To use the vibration button  
press down once to active the speed, press  
again for a Medium speed and once more for  
the faster speed. Press to reduce the speed.  
Voice Activation  
Indicator  
MUSIC CENTER  
NIGHT LIGHT: To use the night light, press  
the button. The light has 3 settings of  
brightness and is controlled by the button.  
The Music Center is designed to be attached to  
the playard corners. It can be attached on the  
Changing Table's side or the Canopy's side. See  
figure 37.  
MP3 Indicator  
VOICE RECORDER: To use the Voice  
record function press the button and  
speak into the microphone to record your 10  
second voice message. Press to hear the  
message.  
VOICE ACTIVATION: To use the Voice  
Activation function press the button twice  
if the unit is power off. If the unit is already  
power on, press the button once. The  
voice activation light will be illuminated  
when in voice activation mode. If your infant  
cries his/her voice will activate the sleep  
music to come on and play. When voice  
activation is enabled, sleep mode is active for  
2 hrs.  
Fig. 37  
MUSIC OPERATION  
_
+
_
The Music Center requires 4 AA batteries. Please  
see figure 38 for battery installation. Unscrew  
the battery door screws and pull outward on the  
battery door. Install batteries as shown. Re-install  
battery door and secure with screws.  
+
_
MP3 FUNCTION: Use the input jack to  
+
_
attach your MP3 player into the unit  
Press the button to select the MP3 input.  
.
+
Your MP3 music will then be played through  
the unit and will over-ride the unit’s music.  
To listen to the unit’s music, depress the  
button. Volume will be controlled by the MP3  
player.  
Fig. 38  
To active the unit, press the on/off button.  
Press button a second time to switch unit off.  
To listen to SLEEP music, press the SLEEP  
button. You may use the previous / next  
button to change the song. The Vol  
Vol buttons control the units volume.  
or  
To listen to PLAY music, press the PLAY  
button. You may use the previous / next  
button to change the song. The Vol or  
Vol buttons control the unit's volume  
Copyright © 2007 - 2009, Baby Trend Inc., All Rights Reserved.  
Copyright © 2007 - 2009, Baby Trend Inc., All Rights Reserved.  
17  
18  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Actiontec electronic Network Router HSP56I User Manual
ADTRAN Network Card T200 T1 HDSL4 User Manual
Aiphone Amplified Phone PG 10A User Manual
Aiwa CD Player CX NMT50 User Manual
Amana Refrigerator ASD2624HEQ User Manual
Amana Refrigerator W10211588A User Manual
American Standard Plumbing Product 2555602 User Manual
Avenview Switch SW HDSDI 8X1 User Manual
Bacharach Carbon Monoxide Alarm Gas Leak Detection User Manual
Beko Refrigerator CXFD5104 W User Manual