Model AXT-500
500 Watt 4-Channel
Bridgeable MOSFET Amplifier
OWNER'S
MANUAL
Download from Www.Somanuals.com. All Manuals Search And Download.
HIGH PERFORMANCE STEREO AMPLIFIER
This power amplifier has been designed to provide high Quality performance with a
minimum of maintenance. However, it's performance will only be as good as the care
and quality of components with which it is installed. We therefore advise that you
read these instructions very carefully to familiarize yourself with the product and it's
features.
HELP!
Monday-Friday 8:30am - 7:00pm Eastern
1-800-645-4994
Should you require assistance with the installation or wiring so this unit, please call
our toll-free "HELP" line at 1-800-645-4994 during the days/hours shown.
Saturday
9:00am - 5:00pm Eastern
SPECIFICATIONS
Maximum Output Power:
500 Watts
Input Impedance:
Input Sensitivity:
Filter type:
Low-Level 10K Ohms
High-Level 100 Ohms
75 Watts RMS x 4
@ 4 Ohms
Low-Level 200 mV - 8 V.
High-Level 2V - 10 V
150 Watts RMS x 2
@ 4 Ohms
2 - 8 Ohms (stereo)
10 - 35KHz. +/-1 dB
Selectable Full/Low-pass
Crossover @ 12dB/Octave
LPF 50-250 Hz (variable)
12 volts, negative ground
30 amps.
Output Impedance:
Frequency Response:
Filter Crossover:
Supply Voltage:
Channel Separation:
Signal / Noise Ratio:
60 dB
Fuse Rating:
90 dB (A-Weighted)
Dimensions (W X H X D):
295 mm X 54.3 mm X 230 mm
11-5/8" X 2-1/8" X 9"
* Due to continuing improvement, Audiovox reserves the right to change features and design without notice.
-3-
Download from Www.Somanuals.com. All Manuals Search And Download.
PRECAUTIONS
1. Although this unit is designed with built-in self-protection circuits, there may be a possibility of damage if it is not wired
correctly. Please follow the wiring instructions carefully for the type of system being used.
2. The last lead to be connected is the wire to the positive( ) terminal of the battery. Connect this wire only after having
+
completed and checked all other connections to the amplifier.
3. By nature of its design, a power amplifier generates heat and requires good air circulation around it to dissipate that
heat. Do not install the amplifier in an enclosed area which does not permit adequate air circulation. Should the
temperature of the unit rise too high, the internal thermal sensors will shut off operation until it has cooled down
sufficiently.
4. If fuse replacement is necessary, use only fuses of the same ampere rating as originally supplied with the unit. The
use of fuses with incorrect ratings may cause serious damage to the amplifier. If fuses blow consistently, carefully
check all electrical connections to the unit.
5. Supply of adequate battery voltage is critical to the proper operation of the power amplifier. The leads to the battery
and chassis ground must be of a thick enough gauge to provide this voltage to the amplifier. We recommend #10 gauge
wire or thicker (smaller gauge #) for the battery and ground leads.
6. Make certain that the speaker(s) to be used with this amplifier are capable of handing the output power (wattage) of
the unit. Use of speaker(s) not rated for the output of this amplifier may cause damage to or failure of the speaker(s)
for which Audiovox will not be liable.
-4-
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION INSTRUCTIONS
INSTALLATION DIAGRAM
1. Select a mounting area where the amplifier will
have sufficient air circulation for proper cooling.
Inadequate air circulation will cause the temperature
of the amplifier to rise and will trigger the thermal
protection mode.
2. Place the amplifier on the mounting surface and
mark the locations of the four mounting holes as
shown in the illustration.
3. Remove the amplifier and drill a 1/8" hole at
each of the four locations.
CAUTION: Before drilling the holes, look at the
underside of the mounting surface. Always check
carefully to avoid drilling into wiring, braces, fuel
or brake lines.
CHECK BEFORE YOU DRILL!
4. Secure the amplifier to the mounting surface using
The self-tapping screws provided.
-5-
Download from Www.Somanuals.com. All Manuals Search And Download.
WIRING INSTRUCTIONS
The wiring of your amplifier will depend on the system and speakers you are using but will either be a stereo, mono, or
mixed-mono application. The following pages illustrate the input and output wiring for these types. please refer to the
appropriate diagrams for the system configuration you are using. The power and speakers wire connections for this amplifier
are made via screw tightened terminal blocks. Loosen the screw for the connection to be made and fully insert the wire
(strip 1/2" of insulation from the end) under the respective screw on the side panel (crimp-on "U" terminals are provided
to simplify wiring and we recommend their use.). Tighten the screw down to secure the wire.
1. Power Connection
The battery terminal (BATT) must be connected directly to the positive terminal of the vehicle battery to provide an
adequate voltage source and minimize noise. Connecting the battery terminal lead to any other point (such as the fuse
block) will reduce the power output and may cause noise and distortion. Use only ##1100 gauge or thicker (smaller gauge
#) wire for this lead and connect it to the terminal of the battery after all other wiring is completed.
2. Ground Connection
The ground terminal (GND) connection is also critical to the correct operation of the amplifier. Use a wire of the same
gauge as the power connection (##1100 or thicker) and connect it between the ground terminal (GND) of the amplifier and
a metal part of the vehicle close to the mounting location. This wire should be as short as possible and any paint or rust
at the grounding point should be scraped away to provide a clean metal surface to which the end of the ground wire can
be screwed or bolted.
3. Remote Turn-On Connection
The amplifier is turned on by applying +12 volts to the remote turn-on terminal (REM). The wire lead to this terminal
should be connected to the "Auto-Antenna" lead from the car stereo which will provide the +12 volts only when the car
stereo is turned on. If the car stereo does not provide an Auto-Antenna lead, the remote turn-on lead may be wired to
an "Accessory" or "Radio" terminal in the car's fuse block. This will turn the amplifier on and off with the ignition key,
regardless of whether the car stereo is on or off. The remote turn-on lead does not carry large currents, so #20 gauge
wire may be used for this application.
-6-
Download from Www.Somanuals.com. All Manuals Search And Download.
WIRING INSTRUCTIONS
4. Speaker Connections
Depending on the type and number of speakers used with the amplifier, wire them to the speaker terminals as per the
appropriate wiring diagram. For most applications, #16 gauge wire should be used for the speaker leads but in no case
thinner than #18 gauge. For leads in excess of 10 feet, #14 gauge is recommended. When wiring the speakers, pay
careful attention to the polarity of the terminals on the speakers and make certain they correspond to the polarity of the
corresponding terminals on the amplifier. DO NOT ground any speaker leads to the chassis of the vehicle.
5. Input Connections
This amplifier features both high and low-level input capability. Use either the low-level or high-level inputs, not both.
If low-level outputs are provided from the car stereo, it is recommended that the low-level inputs be used for lowest
distortion and best performance. Use good quality shielded audio cables with RCA plugs at both ends to connect
the stereo to the amplifier and keep the cable lengths to a minimum to avoid noise.
If the car stereo does not provide low-level outputs, the amplifier may be connected via the speaker (high-level)
outputs from the stereo. Wire the speaker leads from the car stereo to the 5-pin adaptor harnesses as shown in the
diagram (shielded cable is not required for this application) and plug the connectors into the mating High-Level Input
socket on the amplifier. Carefully splice and insulate all wire connections.
CAUTION: Use either the low-level or the high-level inputs on the amplifier.
DO NOT use both input levels at the same time.
-7-
Download from Www.Somanuals.com. All Manuals Search And Download.
4-CHANNELAND MIXED-MONO INPUT WIRING DIAGRAM
LOW-LEVEL RCA OUTPUTS
HIGH-LEVEL
(SPEAKER) OUTPUTS
Left Rear
CAR STEREO
Left Front +
NOTE: When using High-Level (Speaker) Outputs
of car stereo, connect only the Positive (+)
wires to the amplifier. Do not use Negative (-)
Output wires (insulate ends with tape and
leave disconnected)
Right Front +
Right Rear
Right Front
Left Rear +
Right Rear+
Left Front
CHASSIS GROUND ON RADIO
IMPORTANT
USE EITHER HIGH-LEVEL OR
LOW-LEVEL INPUT, NOT BOTH.
RCA TYPE
SHIELED CABLES
(NOT INCLUDED)
TO CH1
TO CH2
TO CH4
TO CH3
(WIRE SIDE VIEW)
HI-INPUT
4CH
2CH
X-OVER
X-OVER
PWR
4CH
1CH
3CH
2CH
PRT
FULL
LPF
FULL
LPF
GND
50Hz
250Hz
MIN
MAX
MIN
MAX
50Hz
250Hz
LPF
GAIN
GAIN
LPF
3CH
1CH
-8-
Download from Www.Somanuals.com. All Manuals Search And Download.
4-CHANNELAND MIXED-MONO OUTPUT WIRING DIAGRAM
EXISTING SCREW OR BOLT CLEAN PAINT, RUST, DIRT
OR GREASE FROM AREA FOR GOOD CONNECTION.
SPEAKER IMPEDANCE
4-CHANNEL MODE: 2-8 OHMS
2 CHANNEL MODE: 4-8 OHMS
LEFT
SPEAKER
RIGHT
SPEAKER
GROUND METAL
SECTION OF VEHICLE
LEFT REAR
SPEAKER
RIGHT REAR
SPEAKER
FUSE
CH1
CH2
CH3
CH4
BRIDGED
BRIDGED
BATT
REM
GND
USE #10 GAUGE
WIRE (SEE TEXT)
CH1 / CH2
MIXED-MONO SPEAKER OR
SUB-WOOFER WITH CROSSOVER
4-8 OHMS
CH3 / CH4
MIXED-MONO SPEAKER OR
SUB-WOOFER WITH CROSSOVER
4-8 OHMS
GROUND
CAR STEREO
LEFT FRONT
SPEAKER
BATTERY
FOR 12 VOLT USE ONLY
AUTO-ANTENNA LEAD
-9-
Download from Www.Somanuals.com. All Manuals Search And Download.
3-CHANNEL INPUT WIRING DIAGRAM
HIGH-LEVEL
(SPEAKER) OUTPUTS
CAR STEREO
LOW-LEVEL RCA OUTPUTS
Left Front +
NOTE: When using High-Level (Speaker) Outputs
of car stereo, connect only the Positive (+)
wires to the amplifier. Do not use Negative (-)
Output wires (insulate ends with tape and
leave disconnected)
Right Front +
Mono or Sub-Woofer
Left Rear +
Right Rear+
Right
Left
CHASSIS GROUND ON RADIO
IMPORTANT
USE EITHER HIGH-LEVEL OR
LOW-LEVEL INPUT, NOT BOTH.
RCA TYPE
SHIELED CABLES
(NOT INCLUDED)
TO CH1
TO CH2
TO CH3 / CH4
WIRE SIDE VIEW
HI-INPUT
4CH
2CH
X-OVER
X-OVER
PWR
4CH
1CH
3CH
2CH
PRT
FULL
LPF
FULL
LPF
GND
50Hz
250Hz
MIN
MAX
MIN
MAX
50Hz
250Hz
LPF
GAIN
GAIN
LPF
3CH
1CH
.
NOTE:
“Y” cable must be purchased separately from your local electronics store
-10-
Download from Www.Somanuals.com. All Manuals Search And Download.
3-CHANNEL OUTPUT WIRING DIAGRAM
SPEAKER IMPEDANCE
4-CHANNEL MODE: 2-8 OHMS
2/3-CHANNEL MODE: 4-8 OHMS
EXISTING SCREW OR BOLT CLEAN PAINT, RUST, DIRT
OR GREASE FROM AREA FOR GOOD CONNECTION.
LEFT FRONT
SPEAKER
RIGHT FRONT
SPEAKER
GROUND METAL
SECTION OF VEHICLE
FUSE
CH1
CH2
CH3
CH4
BRIDGED
BRIDGED
BATT
REM
GND
USE #10 GAUGE
WIRE (SEE TEXT)
MONO SPEAKER
OR
SUB-WOOFER
4-8 OHMS
GROUND
CAR STEREO
LEFT FRONT
SPEAKER
BATTERY
FOR 12 VOLT USE ONLY
AUTO-ANTENNA LEAD
-11-
Download from Www.Somanuals.com. All Manuals Search And Download.
2-CHANNEL MONO (BRIDGED) INPUT WIRING DIAGRAM
HIGH-LEVEL
(SPEAKER) OUTPUTS
CAR STEREO
LOW-LEVEL
RCA OUTPUTS
Left Front +
Right Front +
NOTE: When using High-Level (Speaker) Outputs
of car stereo, connect only the Positive (+)
wires to the amplifier. Do not use Negative (-)
Output wires (insulate ends with tape and
leave disconnected)
Right
Left
Left Rear +
Right Rear+
CHASSIS GROUND ON RADIO
IMPORTANT
USE EITHER HIGH-LEVEL OR
LOW-LEVEL INPUT, NOT BOTH.
RCA TYPE
SHIELED CABLES
(NOT INCLUDED)
TO CH1 / CH2
TO CH3 / CH4
(WIRE SIDE VIEW)
HI-INPUT
4CH
2CH
X-OVER
FULL
X-OVER
PWR
PRT
4CH
1CH
3CH
2CH
LPF
FULL
LPF
GND
50Hz
250Hz
MIN
MAX
MIN
MAX
50Hz
250Hz
LPF
GAIN
GAIN
LPF
3CH
1CH
-12-
Download from Www.Somanuals.com. All Manuals Search And Download.
2-CHANNEL MONO (BRIDGED) OUTPUT WIRING DIAGRAM
EXISTING SCREW OR BOLT CLEAN PAINT, RUST, DIRT
OR GREASE FROM AREA FOR GOOD CONNECTION.
LEFT SPEAKER
OR
SUB-WOOFER
4-8 OHMS
RIGHT SPEAKER
OR
SUB-WOOFER
4-8 OHMS
GROUND METAL
SECTION OF VEHICLE
FUSE
CH1
CH2
CH3
CH4
BRIDGED
BRIDGED
BATT
REM
GND
USE #10 GAUGE
WIRE (SEE TEXT)
GROUND
CAR STEREO
BATTERY
FOR 12 VOLT USE ONLY
AUTO-ANTENNA LEAD
-13-
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
2
1 4
3
6
5
7
HI-INPUT
4CH
2CH
X-OVER
X-OVER
FULL
FUSE
PWR
4CH
1CH
3CH
2CH
PRT
FULL
LPF
LPF
GND
50Hz
250Hz
LPF
MIN
MAX
MIN
MAX
50Hz
250Hz
LPF
CH1
CH2
CH3
CH4
GAIN
GAIN
BRIDGED
BRIDGED
BATT
REM
GND
3CH
1CH
If activated by a rise in emperature, the unit will resume
operation after cooling off to a normal operating range.
If activated by an overload condition, the source of the
overload must be found and corrected to resume
operation of the amplifier.
Most overload conditions are caused by mis-wiring or
operation into incorrect speaker loads. Re-check all
wiring and connections if this situation occurs and
correct as necessary.
After initial set-up, the amplifier should not require any
further adjustment unless there is a change in the car
stereo or speaker system with which it is used.
1
2
Power Indicator Lamps
The Power Indicator Lamps will light to indicate that the unit
is connected to the battery and that the Remote
Turn-On terminal is receiving +12 volts, thus turning on the
amplifier.
3 Level (Gain) Controls
The amplifier is capable of operating from sources
supplying a wide range of input levels. The Level controls
should initially be set to the mid-rotation position.
If it is found that there is not enough output even when
the volume control on the car stereo is at its maximum
setting, adjust the Level control to increase the output
Protection Mode LED
This LED illuminates red to indicate that the self-protection
circuits have been activated and have shutoff operation of
the amplifier. The protection circuits may be triggered
by the temperature of the unit rising above a safe level
or by an overload condition.
-14-
Download from Www.Somanuals.com. All Manuals Search And Download.
from the system. If, however, there is still output from
the amplifier when the car stereo volume control is at its
minimum setting, or the output level increases too fast
with a small rotation of the volume control, adjust the
Level control to decrease the output from the system.
Once the correct setting is found, these controls should
not require any further adjustment.
5 LPF Crossover Frequency Control
This Control selects the crossover frequency when the
Sub woofer Crossover Selector
is in the "LPF" setting.
4
Adjust it to the appropriate position for the characteristics
and crossover frequency requirements of the speaker
system with which the amplifier is being used.
6 High Level Input Connection
4
Crossover Selector
If the car stereo not does not provide low-level outputs,
the amplifier may be connected via the speaker (high-
level) outputs from the stereo. Wire the speaker leads
from the car stereo to the 5-pin adaptor harness as
shown in the diagram (shielded cable is not required for
this application) and plug the connector into mating High-
Level Input socket on the amplifier. Carefully splice and
insulate all wire connections.
This switch allows selection of the frequency filters that
permit the amplifier to be used to reproduce the entire
audio range or just the bass range.
In the "FULL" position of the switch, the response is
flat and unaffected so the entire audio frequency
range is reproduced by the amplifier. Use this setting
if the amplifier is being used to power a full range
speaker system in the "LPF" (Low-Pass Filter) setting,
only the bass frequencies below the frequency set by
7
Fuse
5
the Crossover Frequency Control
will be amplified
The circuitry of the amplifier is protected from damage by
an automotive-type fast-blow fuse. If fuse replacement
is necessary, use only fuses of the of the same ampere
rating as originally supplied with the unit. The use of fuses
with incorrect ratings may cause serious damage to the
amplifier. If fuses blow consistently, carefully check all
electrical connections to the unit.
and fed to the speakers. Use this setting if the
amplifier is being used to power a sub-woofer speaker
system.
HPF(High-Pass Filter): Only mid-high tone
(50Hz-250 Hz) Speaker.
-15-
Download from Www.Somanuals.com. All Manuals Search And Download.
90 DAY/122MONTH LLIIMITED WAARRANTY
Applies to car stereo power amplifiers, equalizers and accessories.
AUDIOVOX CORPORATION (the Company) warrants to the original retail purchaser of this product that should this product or any part thereof,
under normal use and conditions, be proven defective in material or workmanship within 90 days from the date of original purchase, such
defect(s) will be repaired or replacedwith new or reconditioned product (at the Company's option) without charge forparts and repair labor.
After the initial 90 day period and for a period of 12 months from the date of original purchase, the Company will supply at no charge a
replacement for any defective part(s) but will charge for the labor to repair the product.
Toobtain repair or replacement within the terms of this Warranty, the product is to be delivered withproof of warranty coverage (e.g. dated
bill of sale), specification of defect(s), transportation prepaid, to an approved warranty station orthe Company at the address shown below.
This Warranty does not extend to the elimination of externally generated static or noise, to correction of antenna problems, to costs incurred
for installation, removal or reinstallation of the product, or damage to tapes, compact discs speakers, accessories, or vehicle electrical
systems.
This Warranty does not apply to any productor part thereof which, in the opinion of theCompany, suffered or has been damagedthrough
alteration, improper installation, mishandling, misuse, neglect, or accident, or by removal or defacement of the factoryserial number/bar code
label(s). THE EXTENT OF THE COMPANY'S LIABILITY UNDER THIS WARRANTY IS LIMITED TO THE REPAIR OR REPLACEMENT
PROVIDED ABOVE AND, IN NO EVENT, SHALL THE COMPANY'S LIABILITY EXCEEDTHE PURCHASE PRICE PAID BY PURCHASER FOR
THE PRODUCT.
This Warranty is in lieu of all other express warranties or liabilities. ANY IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY
OF MERCHANTABILITY, SHALL BE LIMITED TO THE DURATION OF THIS WRITTEN WARRANTY. ANYACTION FOR BREACH OF ANY
WARRANTY HEREUNDER INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY MUST BE BROUGHT WITHIN A PERIOD OF 30
MONTHS FROM DATE OF ORIGINAL PURCHASE. IN NO CASE SHALL THE COMPANY BE LIABLE FOR ANY CONSEQUENTIAL OR
INCIDENTAL DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY, EXPRESS OR IMPLIED, WHATSOEVER. No person or
representative is authorized to assume for the Companyany liability other than expressed herein in connection with thesale of this product.
Some states do not allow limitations on how long an implied warranty lasts or the exclusion orlimitation of incidental or consequential damage
so the above limitations or exclusion may not apply to you. This Warranty gives you specific legal rights and you may also have other rights
which vary from state to state.
U.S.A.
:
:
AUDIOVOX CORPORATION, 150 MARCUS BLVD., HAUPPAUGE, NEW YORK 11788
.
1-800-645-4994
CANADA
CALL 1-800-645-4994 FOR LOCATION OF WARRANTY STATION SERVING YOUR AREA
-16-
Download from Www.Somanuals.com. All Manuals Search And Download.
C
2003
Audiovox Electronics Corporation, Hauppauge, N.Y.
Printed in Korea
128-6561
1
Download from Www.Somanuals.com. All Manuals Search And Download.
|