Audiovox Satellite Radio AVX01BT3CL3 User Manual

Model AVX01BT3CL3  
TRANSMITTERPROGRAMMINGGUIDE  
The transmitters included with the system have been pre-programmed at  
the factory, with each button pre-assigned to control a specific function of  
the system. Although the system in the vehicle has either a 3, 4, or 5 channel  
RECEIVER, depending on the model, the transmitters included with the  
system are 7 channel transmitters. This allows you to program each  
transmitter to more than one vehicle in two car families and also allows you  
to change which button or buttons control certain functions of the system.  
(Example: Transmitter channel 5, shown below, can be programmed to  
activate Receiver channel 2.) Refer to the chart below for access to each of  
the transmitter channels, and for the standard factory button assignments.  
TRANSMITTER  
CHANNEL BUTTONS CHANNEL  
SYSTEMRECEIVER  
FUNCTION  
1
1
Remote Arm  
* Remote Emergency Panic  
**Remote Door Lock  
2
2
RemoteDisarm  
*Remote Emergency Panic  
***Remote Unlock Drivers Door  
**Remote Unlock All Doors  
3
3
Push And Hold For 3 Seconds For Opt1  
Release, Push 2 Times For Aux. Out.  
4
5
6
7
&
&
&
4
5
-
**** Pulsed Output for Accessories  
**** Switched Output for Accessories  
**** RF  
**** RF  
&
&
-
* Remote Emergency Panic is available only on certain models.  
** Door Lock/Unlock may require additional components in certain vehicles.  
*** Unlock Driver Door or Unlock All Doors May Require Additional Components  
**** Some of the more common accessories for these additional channels are;  
AS 9075  
AS 9256  
AS 9154  
AS 9153  
Remote Car Starter  
Remote Trunk Release Relay  
Remote Garage Door Interface  
Remote Window Roll Up  
128-6105  
1 of 6  
Released 7-25-01.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
The chirp tone confirms that programming ofchannel 1 was successful.  
Upto4transmitterscanbeprogrammed, pressandholdtheselected  
button of each additional transmitter until the chirp tone is heard, or  
move to step #5  
(b) You can assign the Lock/Unlock, Arm/Disarm button, by pressing  
and holding the lock/unlock button until the siren emits a long chirp  
tone.  
The chirp tone confirms that programming of channel 1 was  
successful. Up to 4 transmitters can be programmed, press and hold  
the selected button of each additional transmitter until the chirp tone  
is heard, or press and release the valet pushbutton switch two times  
to advance to step #8.  
5.  
Press and release the valet/override switch one time to advance to  
channel 2.  
6. (a) The dash mounted LED will flash 2 times, and the siren will "chirp"  
2 times indicating that the system is ready to accept programming for  
channel 2. Unlock/2nd Unlock, Disarm, and Panic. Press and hold  
the Unlock button on your keychain transmitter until the siren emits  
a long chirp tone. This confirms that programming of channel 2  
was successful. Up to 4 transmitters can be programmed, press  
and hold the selected button of each additional transmitter until the  
chirp tone is heard.  
(b) Press and release the valet/override switch 1 time then move onto  
step #7 or.  
7.  
8.  
Press and release the valet/override switch one time to advance to  
channel 3.  
The dash mounted LED will flash 3 times, and the siren will "chirp"  
3 times, indicating that the system is ready to accept programming  
for channel 3. Trunk Release Output, (where so equipped), or  
alternate channel output when used.  
9. (a) Press and hold the Opt. button on your keychain transmitter until the  
siren emits a long chirp tone. This confirms that programming of  
channel 3 was successful. Up to 4 transmitters can be programmed,  
press and hold the selected button of each additional transmitter until  
the chirp tone is heard.  
(b) Press and hold the 1st Opt. button on your keychain transmitter until  
the siren emits a long chirp tone. This confirms that programming of  
channel 3 was successful. Up to 4 transmitters can be programmed,  
press and hold the selected button of each additional transmitter until  
the chirp tone is heard.  
3
128-6105  
3 of 6  
Download from Www.Somanuals.com. All Manuals Search And Download.  
10.  
11.  
Press and release the valet/override switch one time to advance to  
channel 4 if so equipped. If your system does not have a 4th channel,  
a long chirp followed by a short chirp tone will indicate that the  
program mode has been exited.  
ThedashmountedLED willflash4times andsirenwill"chirp"4times  
indicating that the system is ready to accept programming of channel 4.  
12. (a)Press and hold any combination of two buttons simultaneously, until  
the siren emits a long chirp tone. This confirms that programming of  
channel 4 was successful. Up to 4 transmitters can be programmed,  
press and hold the selected button of each additional transmitter until  
the chirp tone is heard.  
(b)Press and hold the remaining Opt. button of the transmitter until the  
siren emits a long chirp tone. This confirms that programming of  
channel 4 was successful. Up to 4 transmitters can be programmed,  
press and hold the selected button of each additional transmitter until  
the chirp tone is heard.  
or press and release the push button switch to exit the programming  
mode,  
or turn the ignition switch off to exit the programming mode.  
The siren emits a long followed by a short chirp tone indicating that the  
program mode has been exited.  
NOTE: If programming to a Keyless Entry (non alarm) unit, there will be  
NO chirp indication.  
QUICKREFERENCE:  
You can program any individual channel, without reprogramming all  
channels, by following the quick reference chart below. (Not All Units Have  
4 Channels)  
CHANNEL  
VALETSWITCH  
LED  
Press and Release 3 Times  
1
1 Flash  
Press and Release 4 Times  
Press and Release 5 Times  
Press and Release 6 Times  
2
3
4
2 Flashes  
3 Flashes  
4 Flashes  
After the desired channel is programmed, turn the ignition key to the off  
position to exit programming mode.  
4
128-6105  
4 of 6  
Download from Www.Somanuals.com. All Manuals Search And Download.  
BATTERYREPLACEMENT:  
The transmitter incorporates a small red LED visible through the case. This  
LED can be used to indicate battery condition. You will notice a decrease  
in transmitter range as the battery condition deteriorates. Transmitter  
battery replacement is recommended at least every 10 to 12 months,  
depending upon how frequently the transmitter is used.  
To replace the battery...  
1. Remove the transmitter cover by removing the small screw from the back  
of the transmitter case.  
2. Remove the discharged battery, making note of the orientation of the +  
and - contacts, and dispose of properly.  
3. Install the new (type GP23A) battery, taking care to orient the + and -  
contacts properly.  
4. Replace the transmitter cover, taking care not to damage the LED or  
switches on the circuit board.  
5
128-6105  
5 of 6  
Download from Www.Somanuals.com. All Manuals Search And Download.  
01  
3
3
3
60  
61  
IMPORTANT: To help us expedite your order, please print all of the  
information legibly, and mail this form and your payment according to the  
instructions below. Please indicate which button pad is used with your  
transmitter as indicated above.  
Transmitter model number is found on rear case.___________________  
1. Name : _________________________________________________  
Address : __ ___________________________________________  
City : ___________________ State : ______ Zip Code : __________  
2. Telephone Number : (________) _____________________________  
3. Enter the total number of transmitters required here : _____________  
4. The cost per transmitter is $ 65.00.  
5. Enter the total amount enclosed here : ________________________  
( New York state residents must include the appropriate sales tax. )  
6. Method of payment; check one of the boxes below.  
Mastercard Visa Check or money order * (do not send cash)  
* Make checks payable to Audiovox Corporation  
7. Credit Card Number : ______________________________________  
8. Credit Card Expiration Date : __________________________  
Credit card purchasers can order additional or replacement  
transmitters by phone. Simply dial 1 - 800 - 645 - 4994, and  
follow the instructions from the operator interface.  
9. Mail this form, and your check, to ;  
150  
.
,
. . 11788  
:
128-6105  
128-6105  
6 of 6  
Download from Www.Somanuals.com. All Manuals Search And Download.  

3D Connexion Sewing Machine 7318 User Manual
AEG Clothes Dryer 88840 User Manual
AEG Refrigerator 2842 6 DT User Manual
Agri Fab Spreader 45 03881 User Manual
Alcatel Lucent Network Card 7342 ISAM FTTU User Manual
AllerAir Air Cleaner 5000 DH User Manual
Alto Shaam Oven 714ES Series User Manual
American Audio Turntable TTD 2500 User Manual
AMX Stereo Receiver HDMI UTPRO 0808 User Manual
Atlona Telephone AT USB50 SR User Manual