DV2 USB
Professional Preamp Mixer
5/11
Download from Www.Somanuals.com. All Manuals Search And Download.
DV2 USB
Safety Precautions
• For adult use only - Keep out of the reach of children.
• Be sure that the local power outlet match that of the required voltage of the unit.
• Disconnect from main power before making any type of connection.
• Do not attempt any service. There are no user serviceable parts inside.
• Never plug this mixer in to a dimmer pack
• Always be sure to mount this mixer in an area that will allow proper ventilation.
• Do not attempt to operate this mixer, if it becomes damaged in any way.
• Never operate this mixer when it’s covers are removed
• To reduce the risk of electrical shock or fire, do not expose this mixer rain or moisture
• This mixer is intended for indoor use only, use of this product outdoors voids all warranties.
• During long periods of non-use, disconnect the mixer’s main power.
• Always mount this mixer in safe and stable matter.
• Power Cord Protection - Power supply cords should be routed so that they are not likely to be
walked on or pinched by items placed upon or against them, paying particular attention to cords
at plugs, convenience receptacles, and the point where they exit from the mixer.
• Cleaning -The mixer should be cleaned only as recommended by the manufacturer.
• Heat -The mixer should be situated away from heat sources such as radiators, heat registers,
stoves, or other mixers (including amplifiers) that produce heat.
• Be sure to save the packing carton in case you may ever have to return the mixer for service.
• Read all documentation before attempting to operate your new mixer. Please save all your docu-
mentation for future reference.
• Do not spill water or other liquids in to or on to your mixer.
• Do not attempt to operate this mixer if the power cord has been frayed or broken. Please route
your power cord out of the way of foot traffic .
• Always have the front gain controls set to their lowest level during initial power-up to prevent
speaker damage.
• The mixer should be serviced by qualified service personnel when:
A. Objects have fallen, or liquid has been spilled into the mixer.
B. The mixer has been exposed to rain or water.
C. The mixer does not appear to operate normally or exhibits a marked change in
performance.
DV2 USB
Main Features
• Adjustable Crossfader Curve
• 2 Phono/2 Aux, 2 Line Inputs
• Fader “Q” Start
• Q-Start Compatible (for use with compatible
American Audio CD Players )
• -30dB Rotary Kills for Treble, Bass and
Mids on both channels
• Soft-touch rubber knobs for better control
• Extremely clean signal to noise ratio
• Light Control Signal Output Jack
• Talk Over Button - Reduces channel output
gain by 15dB +/- 1.5 dB
• Dual Function Stereo LED Level Indicator -
Indicated Master and PFL (Pre Fader Level)
Signal Levels
• Split Cue Monitoring
• Cue Mixing
• Separate gain control for each channel
• MIDI Interface
• Separate Mic EQ Section
• -30dB% Push Button Kills
• High Output Headphone Jack
• Adjustable Channel Fader Curve
• Built-In 4 In/4 Out USB Audio Interface
• Asio Driver Compatiable for PC/Core Audio for
Mac
©American Audio®
-
-
DV2 USB Instruction Manual Page 3
Download from Www.Somanuals.com. All Manuals Search And Download.
DV2 USB
Quick Start Instructions
American Audio would like to thank for your purchase of this great product. For those of you that are to
impatient to read the entire user manual we have compiled these quick start instructions. We hope that
you will at least read through these instructions to familiarize yourself with the basic understanding of
the unit. The DV2 USB is part of American Audio’s continuing evolution in audio technology. This unit
has been built and designed with the typical DJ in mind, by DJ’s. We have attempted to provide you
with the most reliable product on the market by using only components made from quality products.
MaSter LeVeL - Use this level control to set your volume output. Try never to send an output of
more than +4dB to your system. Signal at levels higher than this will start to distort and may cause
damage to your system and speakers. Remember that a distorted signal from you mixer will only be
multiplied throughout your system.
ChanneL GaIn LeVeL - The channel trim levels are not to be used as volume controls, never use the
channel gain to set the output volume. These controls are used to aid in distortion control. Use these
control to preset your signal level before the crossfader. With your channel faders in the maximum
position, use the channel trim level to set an average output level of about +4dB on you master level
meter.
heaDPhOneS - To avoid severe hearing damage, always be sure the headphone level is set to mini-
mum before plugging them in. Never put the headphone on without making sure the headphone level
is turned down.
MIC - The mic connector uses a 1/4” jack unbalanced connector. The DJ mic has an independent
volume control. When feedback occurs when using the mic, try lowering the “low” level this may
reduce the feedback. Always leave the mic level to it’s minimum level when not in use.
PhOnO/aUX SWItCh (25) - This switch is used to change the selected input from phono level to
line level and vice versa. Channels 1 and 2 may be switched PHONO/AUX or LINE. The selectors for
AUX1/PHONO1 and AUX2/PHONO2 are on the rear panel.
Q-Start FeatUre - This function works in conjunction with a compatible American Audio or Ameri-
can DJ “Q”Start CD player. When used with a compatible CD player, you can use the crossfader to
start and stop the CD Player with the slide of the fader. The ON/OFF “Q ”START switch activates this
FADER “Q ”START feature.
CrOSSFaDer CUrVe aDjUStMent- This rotary knob is used to change the way the crossfader
will operate. The crossfader can operate in three different modes, NORMAL CURVE, QUICK CURVE
and any variation of the two. (Quick Curve usually used for crabbing).
ChanneL FaDer CUrVe aDjUStMent - This rotary knob is used to change the way the channel
fader will operate. Each channel has a Curve adjustment. The curve on the faders adjust from long or
short or any variation of the two.
reVerSe FUnCtIOn - Both the crossfader and the channel faders will reverse function when the
reverse switch is activated.
©American Audio®
-
-
DV2 USB Instruction Manual Page 4
Download from Www.Somanuals.com. All Manuals Search And Download.
DV2 USB
Controls and Features
Top Panel
14
15
16
17
13
1
2
12
3
4
5
11
10
9
8
6
7
1. MaSter VOLUMe COntrOL - This rotary knob is used to control the master output level (volume).
To avoid distorted output try to maintain an average output signal level +4 dB. Be sure this volume
control is always set to zero before turning the unit on.
2. CUe MIXInG COntrOL - This knob selects the channel for monitoring. The monitor signal comes
from the Prefader. This means it will not be affected by the channel faders. You can monitor each chan-
nel individually. Connect your headphones to the HEADPHONES jAck (36). Turn the CUE MIXING
CONTROL to CUE and select the desired channels with the PFL switches. When you turn the CUE
MIXING CONTROL to PGM (PFL switches without function), you can cue the output signal of the mixer.
If the CUE MIXING CONTROL is set to the center position, you can cue both the channel signal you
selected and the output signal.With the CUE LEVEL control, you can adjust the phones volume without
changing the output signal.
3. CUe LeVeL VOLUMe COntrOL - This knob is used to adjusts the headphone volume output
level. Turn the knob in a clockwise direction to increase the headphone volume.
4. MIDI BUttOn - This button activates the MIDI function.
5. LeVeL InDICatOr MODe SeLeCtOr - This button is used to change the operating mode of the
LEVEL INDIcATORS (15). When the switch is in the Master L/R position, the meter will indicate the
master output levels. When the switch is in the PFL CH1/CH2 position the meter will use the left side
of the meter to indicate channel one’s prefader level and use the right side of the meter to indicate
channel two’s prefader level.
©American Audio®
-
-
DV2 USB Instruction Manual Page 5
Download from Www.Somanuals.com. All Manuals Search And Download.
DV2 USB
Controls and Functions Cont.
6. Q-Start On/OFF SWItCh - This function works in conjunction with a compatible American
Audio® or American DJ® “Q” Start CD player. When used with a compatible CD player, you can use the
crossfader to start and stop the CD play. The ON/OFF “Q” START switch activates the fader “Q” start
feature. When the fader “Q” start feature is activated sliding the cROSSFADER (7) from left to right will
play or cue any CD player connected to the cONTROLLER jAckS (21) on the rear of the unit.
For example, connect a compatible dual CD player connect to mixer channels one and two
(refer to your CD player manual for proper set-up). Be sure the Fader “Q” Start feature is
activated on both channels. Slide the crossfader to the channel one position (full left) and
begin playback on CD drive one. Slide the crossfader to the channel position (far right). This
will immediately trigger the play function on CD drive two and return CD drive one to cue
mode. To return to normal fader operation turn the Fader “Q” Start ON/OFF SWITCH to the
OFF position.
7. CrOSSFaDer - This fader is used to blend the output signals of channels one and two together.
When the fader is in the full left position (channel 1), the output signal of channel one will be controlled
by the master volume level. The same fundamentals will apply for channel two. Sliding the fader from
one position to another will vary the output signals of channels one and two respectively. When the
crossfader is set in the center position, the output signals of both the channels one and channels two
will be even.
8. ChanneL FaDer - These faders are used to control the output signal of any source assigned to
its particular channel.
9. SOUrCe SeLeCtOr SWItCh - This switch routes the audio from the selected source to the cor-
responding channel. Setting the source to the USB position will route the audio from your computer to
the mixer.
Note: When the MIDI funtion is active the switch is deactivated to prevent accidental source
selection. In MIDI, external sources can be routed by setting your software to AUX or external
audio.
10. PFL BUttOnS - These buttons are used to activate a channels “CUE” mode. A red LED next
to the PFL button will glow when a channels cue mode is activated. Cue mode will send a channels
incoming signal to the headphones. The cue level is adjusted by the cuE LEVEL VOLuME cONTROL
(3). Be sure the cue level is set to minimum before putting a pair of headphones on. Be sure the cuE
MIxINg kNOb (2) is turned to the “CUE” position to hear the selected channel source.
11. taLkOVer BUttOn - When engaged this function will decrease all signal levels, except the
microphone level, by 15dB. A red LED next to the TALKOVER BUTTON will glow when the talkover
function is engaged. In the OFF position all signals will remain at their normal levels.
12. MICrOPhOne eQ SeCtIOn - These controls are used to adjust the microphone treble level and
bass levels. Each microphone input has a separate channel EQ.
MICrOPhOne treBLe COntrOL - This knob is used to adjust the treble levels of the
Microphone with a maximum signal gain of +10dB or maximum signal decrease of -30dB.
Turning the knob in a counter-clockwise direction will decrease the amount of treble
applied to the microphone signal, turning the knob in a clockwise direction will increase
the amount of treble applied to microphone signal.
MICrOPhOne BaSS COntrOL - This knob is used to adjust the low frequency levels of
the microphone with a maximum signal gain of +10dB or maximum signal decrease of -30dB.
Turning the knob in a counter-clockwise direction will decrease the amount of bass applied to
©American Audio®
-
-
DV2 USB Instruction Manual Page 6
Download from Www.Somanuals.com. All Manuals Search And Download.
DV2 USB
Controls and Functions Cont.
the microphone signal, turning the knob in a clockwise direction will increase the amount
of bass applied to microphone signal.
13. MICrOPhOne VOLUMe - This knob is used to regulate the microphone output volume. Turning
the knob in a clockwise direction will increase the volume level.
14. ChanneL eQUaLIzer (“rOtarY/PUSh kILLS” - BaSS/MID/treBLe COntrOL) - All of the
channels include a three-band signal EQ. These controls are used to increase or decrease the LOW’s,
MID’s, and HI’s of the output signal.
ChanneL treBLe COntrOL - This knob is used to adjust the treble levels of a channel
allowing for a maximum treble gain of 10dB or maximum decrease of -30dB. Turning the knob
in a counter-clockwise direction will decrease the amount of treble applied to a channel signal,
turning the knob in a clockwise direction will increase the amount of treble applied to a channel
signal.
ChanneL MIDranGe COntrOL - This knob is used to adjust the midrange levels of a
channel allowing for a maximum midrange gain of 10dB or maximum decrease of -30dB.
Turning the knob in a counter-clockwise direction will decrease the amount of midrange ap-
plied to a channel signal, turning the knob in a clockwise direction will increase the amount of
midrange applied to a channel signal.
ChanneL BaSS COntrOL - This knob is used to adjust the low frequency levels of a chan-
nel allowing for a maximum bass gain of 10dB or maximum signal decrease of -30dB. Turning
the knob in a counter-clockwise direction will decrease the amount of bass applied to a chan-
nel signal, turning the knob in a clockwise direction will increase the amount of bass applied to
a channel signal.
eQUaLIzer BanD kILLS - These buttons are used to cut out the Treble, Mid or Bass fre-
quencies of the incoming audio signal. When these buttons are depressed the selected fre-
quency level is cut by -30dB. When a Cut Button is engaged a red LED located directly above
the specific button will begin to glow, indicating the cut function has been activated. Depress-
ing the Cut Button will disengage the cut function.
15. LeVeL InDICatOrS - The dual LED’s indicators are used to indicate either the master output level
or the PFL level’s of channels one and two. The level indicators will directly reflect the operating mode
of the FADER ASSIgN SwITcH (5).
16. ChanneL GaIn COntrOL - This adjustment is used to adjust an audio source signal input gain
for a channel. Never use the gain control to adjust output volume. Setting the gain level properly will
ensure a clean output signal. To properly set the gain level controls:
1. Be sure the MASTER VOLuME cONTROL (1) is set to minimum (zero output).
2. Set the cHANNEL FADER (8) to level 7.
3. Begin play on an audio source connected to the channel you are adjusting.
4. Be sure the LED LEVEL INDIcATOR FuNcTION SwITcH (5) is set to the PFL CH1/CH2
position.
5. Turn the PFL (10) function on, for the channel you are adjusting.
6. Use the gAIN cONTROL (16) to achieve an average output level of +4 dB.
17. MaIn POWer InDICatOr - This LED will glow when the power is turned On.
©American Audio®
-
-
DV2 USB Instruction Manual Page 7
Download from Www.Somanuals.com. All Manuals Search And Download.
DV2 USB
Controls and Features Cont.
18
19
20
21
22
23
32
31 30 29 28 25 27 26 25 24
18. aC COnneCtIOn - This connector is used to supply main power to the unit via the included
detachable power cord. Use only the supplied, polarized AC power cord. This cord is designed to fit in
one direction only. Do not attempt to force a cord in if it does not fit, be sure the cord is being inserted
properly
19. MaIn POWer SWItCh - This is the main power ON/OFF button. The power switch will glow red
when power is ON. Before main power is applied, be sure you have made all connections to the mixer.
Also be sure your amplifier(s) is(are) tuned off. Remember to avoid damaging pops, the mixer should
be powered on first and turned off last.
20. USB POrt - Use this jack to connet to a computer.
21. PLaYer COntrOL - These jacks are used to control the “Q-Start” function between the mixer
and a compatible American Audio CD Player. Input mini plugs from CD player controller into these
jacks, input CD 1 into jack A and CD 2 into jack B.
22. LIGht COntrOL - This jack provides a preset mono audio signal output. There is no way to
adjust this level, however this level will directly reflect the output level of the cHANNEL FADERS (8).
This buffered audio output should only be used for light controllers that can accept an external audio
input. Great for Touch Panels and Chase Controllers.
23. MICrOPhOne jaCk - This jack is used to a connect a microphone to the mixer. Connect you
microphone via 1/4 inch (6.3mm) jack. The signal volume will be controlled by the MIc VOLuME kNOb
(13). The bass and treble levels can also be adjusted by the built-in MIcROPHONE EQ (12).
24. GnD (GrOUnD terMInaL) - Connect each of your turntables ground leads to either of the two
ground terminal. This will reduce the humming and popping noises associated with magnetic phono
cartridges.
©American Audio®
-
-
DV2 USB Instruction Manual Page 8
Download from Www.Somanuals.com. All Manuals Search And Download.
DV2 USB
Controls and Features Cont.
25. LIne LeVeL SeLeCtOr SWItCh - This switch is used to change the mode of PHONO INPuT
jAckS (26 and 28). When connecting turntable to these jacks be sure the switch is in the PHONO
position, and when using line level input devices be sure this switch is in the AUX position. Always be
sure main power is shut off before change the position of the Line Level Selector Switch.
26. ChanneL 1: PhOnO 1 InPUt/aUX 1 jaCkS - The type of input must directly reflect the selected
mode of the LINE LEVEL SELEcTOR SwITcH (25). Connect turntables equipped with MM pickup car-
tridge to PHONO inputs (All DJ turntable use MM pick-up cartridges). CD players or Tape Decks and
other line level instruments may be connected to these jacks as long as the LINE LEVEL SELEcTOR
SwITcH (25) is in the “AUX 1” position. The red colored RCA jack represents the right channel input
and the white represents the left channel input.
These RCA jacks are also routed to the USB interface inputs. Allowing you to record phono or
line level signals via the Aux level inputs. This can also be used with drivers that support
multiple channel USB audio streams on DJ software.
27. ChanneL 1: LIne 1 rCa InPUt jaCkS - These Jacks are used for line level inputs. Connect
CD players or Tape Decks to LINE inputs. Line level musical instruments with stereo outputs such as
Rhythm Machines or Samplers should also be connected to LINE inputs. Turntables should only be
connected to “Phono” inputs. The red colored RCA jack represents the right channel input and the
white represents the left channel input.
28. ChanneL 2: PhOnO 2 InPUt/aUX 2 jaCkS - The type of input must directly reflect the selected
mode of the LINE LEVEL SELEcTOR SwITcH (25). Connect turntables equipped with MM pickup car-
tridge to PHONO inputs (All DJ turntable use MM pick-up cartridges). CD players or Tape Decks and
other line level instruments may be connected to these jacks as long as the LINE LEVEL SELEcTOR
SwITcH (25) is in the “AUX 2” position. The red colored RCA jack represents the right channel input
and the white represents the left channel input.
29. ChanneL 2: LIne 2 rCa InPUt jaCkS - These Jacks are used for line level inputs. Connect
CD players or Tape Decks to LINE inputs. Line level musical instruments with stereo outputs such as
Rhythm Machines or Samplers should also be connected to LINE inputs. Turntables should only be
connected to “Phono” inputs. The red colored RCA jack represents the right channel input and the
white represents the left channel input.
These RCA jacks are also routed to the USB interface inputs. Allowing you to record phono or
line level signals via the Aux level inputs. This can also be used with drivers that support
multiple channel USB audio streams on DJ software.
30. reC OUt - This is a low current unbalanced output source designed for various tape and CD
recorders. The Record Out (REC OUT) level is dictated by the cHANNEL FADER LEVEL (8), it is not
influenced by the MASTER VOLuME cONTROL (1).
31. rCa MaSter OUtPUtS - The RCA master output unbalanced jacks send a low current unbal-
anced output signal.
32. BaLanCeD XLr MaSter OUtPUtS - The Master Output includes a pair XLR Balanced
JACKS as well as a pair RcA uNbALANcED jAckS (31). The 3-pin XLR jacks send a high current
balanced output signal. These jacks should be used when you will be driving an amp or other audio
equipment with a balanced input, or whenever you will be running a signal line greater than 15 feet.
Always, use these jacks whenever possible.
©American Audio®
-
-
DV2 USB Instruction Manual Page 9
Download from Www.Somanuals.com. All Manuals Search And Download.
DV2 USB
Controls and Features Cont.
33
34
35
36
33. ChanneL FaDer CUrVe aDjUStMent - This rotary knob is used to change the way the chan-
nel fader will operate. Each of the two channels has a “Curve” adjustment. The curve on the faders
adjust from long or short or any variation of the two. The shorter the curve adjustment the sooner full
volume will be reached.
34. CrOSSFaDer CUrVe aDjUStMent - This rotary knob is used to change the way the cross-
fader will operate. The crossfader can operate in different modes, “NORMAL CURVE”, “QUICK CURVE”
or any variation of the two. (Quick Curve usually used for crabbing).
35. reVerSe FUnCtIOn SWItCh -
CROSSFADER REVERSE - When the Crossfader reverse switch is activated the LED above it
will light up. When this mode is activated the left side of the crossfader is Ch. 2 and the right
side is Ch.1.
PGM REVERSE - When reversing the channel faders, moving the fader in an upwards direc-
tion will decrease channel volume and moving the fader in a downwards direction will increase
channel volume.
36. heaDPhOne OUtPUt jaCk - This jack is used to connect your headphones to the mixer allow-
ing you to monitor the cue source. Use headphones only rated at 8 ohms to 32 ohms. Most DJ head-
phones are rated at 16 ohm, these are highly recommended. Always be sure the cuE LEVEL VOLuME
(3) is set to minimum before you put the headphones on.
©American Audio®
-
-
DV2 USB Instruction Manual Page 10
Download from Www.Somanuals.com. All Manuals Search And Download.
DV2 USB
USB audio Interface
Use of the DV2 USB audio interface can be used in several modes to mix computer audio from
media player software. You may use the DV2 as your default sound card, or in the media player
options set the mixer as the speaker output for the desired media player. Note: Some media play-
ers may not have this option. Most commonly the USB audio interface may be used with one of
the many DJ software programs that are available for computers. American Audio has provided
software to get you started.
aSIO DrIVer InStaLLatIOn:
Most Windows based computer systems will not support multiple channel USB audio routing. Asio
drivers are necessary to support multiple sets of stereo outputs. Enclosed with the provided soft-
ware CD you will find Asio driver installation software for 32 and 64 bit operating systems. The Asio
Mac users do not need ASIO drivers. Multiple channel streams are supported with core Audio.
rOUtInG USB aUDIO:
The DV2 is equipped with a built-in 4 in/4 out USB audio interface to integrate the use of the ever
growing popularity of DJ software, Digital Vinyl systems, Media Players, or Production software into
your mix.
eXternaL aUDIO rOUtInG:
With the MIDI turned “Off” on the DV2, channel 1 will receive the audio that is assigned to USB
channels 1 & 2. Channel 2 will receive the audio that is assigned to USB channels 3 & 4. Note: Not
all software supports this set up, check the audio routing under your software options.
The RCA inputs are routed to the USB inputs. The signal sent to the USB is dependent of the Source
Selector Switch. To allow the use of the DVS software when the source select switch is set to USB,
the RCA Phono/Aux inputs are routed to the USB inputs, this allows you to route the RCA input sig-
nals through software and layer them with your favorite software FX.
To record with DAW software for sampling, the USB input will route the selected source to the soft-
ware USB input. Check your software manual to set up the DV2 as the input source for recording.
Note: When recording a RCA Phono/Aux can be monitored thru the USB setting. Do not make
adjustments to the Gain or EQ of the channel when auditioning audio, this will affect record levels.
Recording levels should be set to the desired level beforehand.
MIDI anD InternaL aUDIO rOUtInG:
When MIDI is enabled on the DV2 the USB Audio is routed to function with software that supports
MIDI and requires internal audio routing. This mode will route the sound from your software, and
the volume levels will be controlled via the MIDI parameter on the MIDI controls. The headphones
become USB channel dependent make sure to assign Asio/Core channels 3 & 4 to your software’s
headphone output.
©American Audio®
-
-
DV2 USB Instruction Manual Page 11
Download from Www.Somanuals.com. All Manuals Search And Download.
DV2 USB
MIDI table
name
Type
VR
VR
VR
VR
VR
VR
VR
VR
VR
VR
VR
VR
VR
VR
VR
VR
VR
VR
VR
VR
MIDI
2C
2D
2E
2F
30
31
32
33
34
35
36
37
38
39
3A
3B
3C
3D
3E
3F
Remarks
MicGain
MicHig
MicLow
CH1Gain
CH1EqHig
CH1EqMid
CH1EqLow
CH2Gain
CH2EqHig
CH2EqMid
CH2EqLow
Master
CueMix
CueGain
CH1Fader
CH2Fader
Crossfader
CH1Curve
CFCurve
CH2Curve
Ch1HigCut
Ch1MidCut
Ch1LowCut
Ch2HigCut
Ch2MidCut
Ch2LowCut
Level Mode/MASTER LR
TalkOver
SW/LED
SW/LED
SW/LED
SW/LED
SW/LED
SW/LED
SW/LED
SW/LED
SW/LED
SW/LED
SW/LED
SW/LED
SW/LED
LED
01/01
02/02
03/03
04/04
05/05
06/06
07/07
08/08
09/09
0A/0A
0B/0B
0C/0C
0D/0D
0E
Ch1PFL
Ch2PFL
Ch1Reverse
CFReverse
Ch2Reverse
PFL CH1/CH2
LEVEL L
LEVEL
LEVEL
SW
0F
0~A(0~10)
0~A(0~10)
LEVEL R
10
Ch1FaderStar
Ch2FaderStar
20
SW
21
CC-aBSOLUte (Vr)
Control Change messages are sent with status 0xBn, where “n” is the channel, for the specified CC
controller. Thus the controller MIDI ID is indicated with the channel along with the CC number. The
value from 0x00 to 0x7F, is directly related to the location of the controller.
SWItCh On/OFF (SW, Center, CW, CCW)
These messages are used for switches. Control Change messages are sent with status 0x9n,
SWITCH On and Off value are 0x7F and 0x00, where “n” is the channel.
LeD On/OFF (LeD)
These messages are used for LED. Control Change messages are sent with status 0x9n, LED On
and OFF value 0x7F and 0x00, where “n” is the channel.
LeVeL LeD (LeVeL)
These messages are used for LEVEL. Control Change messages are sent with status 0x9n, LED
Off value is 0x00 and On value is related to LED amount, 0x01 with one LED, 0x02 with two LED....,
where “n” is the channel.
©American Audio®
-
-
DV2 USB Instruction Manual Page 12
Download from Www.Somanuals.com. All Manuals Search And Download.
DV2 USB
typical Mixer Set-Up
©American Audio®
-
-
DV2 USB Instruction Manual Page 13
Download from Www.Somanuals.com. All Manuals Search And Download.
DV2 USB
typical Mixer Output Connections Set-Up
RCA to 1/4” Patch Cables
Speaker Cables
DV2 USB
Cleaning
Due to fog residue, smoke, and dust, cleaning the mixer should be carried out periodically to optimize
light output.
1. Use normal glass cleaner and a soft cloth to wipe down the outside casing.
2. Use a cleaner specially designed for electronics to spray in and around the knobs and switch.
This will reduce small particle built up that can effect the proper operation of the mixer.
3. Clean should be carried out every 30-60 days.
4. Always be sure to dry all parts completely before plugging the mixer in.
cleaning frequency depends on the environment in which the mixer operates (i.e. smoke, fog residue,
dust, dew).
©American Audio®
-
-
DV2 USB Instruction Manual Page 14
Download from Www.Somanuals.com. All Manuals Search And Download.
DV2 USB
registration
The DV2 USB carries a one year (365 days) limited warranty. Please fill out the enclosed warranty card to vali-
date your purchase. All returned service items whether under warranty or not, must be freight pre-paid and
accompany a return authorization (R.A.) number. The R.A. number must be clearly written on the outside of
the return package. A brief description of the problem as well as the R.A. number must also be written down
on a piece of paper and included in the shipping container. If the unit is under warranty, you must provide a
copy of your proof of purchase invoice. You may obtain a R.A. number by contacting customer support at
(800) 322-6337.
DV2 USB
Warranty
1-Year LIMIteD WarrantY
A. American Audio® hereby warrants, to the original purchaser, American Audio® products to be free
of manufacturing defects in material and workmanship for a period of 1 Year (365 days) from the date
of purchase. This warranty shall be valid only if the product is purchased within the United States of
America, including possessions and territories. It is the owner’s responsibility to establish the date and
place of purchase by acceptable evidence, at the time service is sought.
B. For warranty service, send the product only to the American Audio® factory. All shipping charges
must be pre-paid. If the requested repairs or service (including parts replacement) are within the terms
of this warranty, American Audio® will pay return shipping charges only to a designated point within
the United States. If the entire instrument is sent, it must be shipped in its original package. No acces-
sories should be shipped with the product. If any accessories are shipped with the product, American
Audio® shall have no liability whatsoever for loss of or damage to any such accessories, nor for the
safe return thereof.
C. This warranty is void if the serial number has been altered or removed; if the product is modified in
any manner which American Audio® concludes, after inspection, affects the reliability of the product;
if the product has been repaired or serviced by anyone other than the American Audio® factory unless
prior written authorization was issued to purchaser by American Audio®; if the product is damaged
because not properly maintained as set forth in the instruction manual.
D. This is not a service contract, and this warranty does not include maintenance, cleaning or peri-
odic check-up. During the period specified above, American Audio® will replace defective parts at
its expense, and will absorb all expenses for warranty service and repair labor by reason of defects
in material or workmanship. The sole responsibility of American Audio® under this warranty shall be
limited to the repair of the product, or replacement thereof, including parts, at the sole discretion of
American Audio®. All products covered by this warranty were manufactured after January 1, 1990, and
bear identifying marks to that effect.
E. American Audio® reserves the right to make changes in design and/or improvements upon its prod-
ucts without any obligation to include these changes in any products theretofore manufactured.
F. No warranty, whether expressed or implied, is given or made with respect to any accessory sup-
plied with products described above. Except to the extent prohibited by applicable law, all implied
warranties made by American Audio® in connection with this product, including warranties of mer-
chantability or fitness, are limited in duration to the warranty period set forth above. And no warran-
ties, whether expressed or implied, including warranties of merchantability or fitness, shall apply to
this product after said period has expired. The consumer’s and or Dealer’s sole remedy shall be such
repair or replacement as is expressly provided above; and under no circumstances shall American
Audio® be liable for any loss or damage, direct or consequential, arising out of the use of, or inability
to use, this product.
G. This warranty is the only written warranty applicable to American Audio® Products and supersedes
all prior warranties and written descriptions of warranty terms and conditions heretofore published.
©American Audio®
-
-
DV2 USB Instruction Manual Page 15
Download from Www.Somanuals.com. All Manuals Search And Download.
DV2 USB
Specifications
Model: DV2 uSb, Professional 2 channel Preamp Mixer
POWer SUPPLY:
DIMenSIOnS:
WeIGht:
AC 100~240V, 50/60Hz (Universal)
10”W x 12.25”D x 3.25”H /254 x 320.6 x 100.3 mm
7 Lbs. / 2.77 Kg
CrOSSFaDer:
Feather Fader Plus - VCA detecting fader start control -
Low grounding impedance crossfader
7W typical, 9W w/ full headphone output
33 Ohms
POWer COnSUMPtIOn:
heaDPhOne IMPeDanCe:
enVIrOnMentaL COnDItIOn:Operating Temperature: 5 to 35 deg. C; Humidity: 25 to 85%
RH (non-condensing); Storage Temperature: -20 to 60 ˚C
Input Sensitivity (Level/Impedence) LOaD=47k OhM:
LIne:
-10dB (316mV) / 22K Ohm
-45dB (5.6mV) / 47K Ohms
-45dB (5.6mV) / 6K Ohms
-10dB (316mV) / 47K Ohms
PhOnO:
MICrOPhOne:
aUX:
Output Sensitivity (Level/Impedence) eQ Flat, 0dBV=1Vrms, LOaD=47k Ohms:
MaSter OUtPUt:
BaLanCeD:
reC OUtPUt:
0dBV (1V) / 1K Ohm ±2dB
0dB (1V) / 600 Ohm ±2dB (Single to GND)
-8dB (398mV) / 1K Ohm ±2dB
LIGht COntrOL OUtPUt:
PhOneS (LOaD=32 OhMS):
-9dB (355mV) / 7.5K Ohm ±2dB
-3dB (0.7V) / 33 Oms ±2dB (CUE/PGM)
Maximum Output (Load = 47k, Input 0dB):
MaSter OUtPUt:
reC OUtPUt:
MORE THAN 8dB (2.5V)
MORE THAN 0dB (1V)
PhOneS (LOaD=33 Ohms):
MORE THAN 4dB (1.58V) at HP LEVEL THD=1%
ChanneL BaLanCe: (eQ Flat, Load=47k Ohms): Within 3dB
Frequency response (eQ Flat, Load=47k Ohms):
LIne:
20Hz - 20KHz, +2/-3dB
PhOnO:
aUX:
20Hz - 20KHz, +2/-3dB at Input Level -55dB
20Hz - 20KHz, +2/-3dB
MICrOPhOne:
20Hz - 20KHz, +2/-3dB
S/n ratio (eQ Flat, w/20khz LPF, a-Weighted, Load=47k Ohms):
LIne/aUX:
PhOnO:
MIC:
LESS THAN -75dB at MIC VR Minimum
LESS THAN -70dB at MIC VR Minimum
LESS THAN -66dB
thD - total harmonic Distortion (eQ Flat, w/20khz LPF, a-Weighted, Load=47k Ohms):
MaSter OUtPUt:
LESS THAN 0.02% at MIC VR Minimum
PhOnO: (LOaD = 32 OhMS):
LESS THAN 0.05% at MIC VR Minimum
CrOSStaLk (eQ Flat, w/20khz LPF, a-Weighted, Load=47k Ohms):
LIne 1 & 2:
aUX 1 & 2:
MORE THAN 75dB @ 1KHz between L & R Channels
MORE THAN 70dB @ 1KHz between L & R Channels
Channel equalizer (Load=47k Ohms):
BaSS:
MID:
+10 ±2dB / Less Than -25dB at 70Hz
+10 ±2dB / Less Than -25dB at 1KHz
©American Audio®
-
-
DV2 USB Instruction Manual Page 16
Download from Www.Somanuals.com. All Manuals Search And Download.
DV2 USB
Specifications
treBLe:
+10 ±2dB / Less Than -25dB at 13KHz
Microphone equalizer (Load-47k Ohms):
BaSS:
+10, ±2dB/ Less Than -25dB at 70Hz
treBLe:
+10, ±2dB/ Less Than -25dB at 13KHz
attenuation of talkover (eQ Flat, w/20khz LPF, a-Weighted, Load=47k Ohms):
-15 ±1.5dB
USB PLaYer SeCtIOn (Signal Format: MP3, 44.1k 16bit, MIDI SW On)
Output Level (eQ Flat, 0dB=1Vrms, Load=47k Ohms):
MaSter OUtPUt:
thD (eQ Flat, w/20khz LPF, a-Weighted, Load=47k Ohms):
MaSter OUtPUt: LESS THAN 0.02% (TCD782 TRK2, MASTER VR OUT=0dB)
S/n ratio (eQ Flat, w/20khz LPF, a-Weighted, Load=47k Ohms):
+10 ±2dB (TCD782 TRK2)
MaSter OUtPUt:
MORE THAN 85dB (TCD782 TRK2, 8)
Crosstalk (eQ Flat, w/20khz LPF, a-Weighted, Load=47k Ohms):
MaSter OUtPUt:
MORE THAN 85dB (TCD782 TRK9, 11 @1KHz between L & R Channel)
MORE THAN 85dB (TCD782 TRK2 @1KHz between Channels)
Frequency response (eQ Flat, Load=47k Ohms):
MaSter OUtPUt:
17Hz-16KHz ±1.5dB (TCD781 TRK1, 4, 16)
recording & Playback (Line 1khz, -10dB Input, 44.1k Sample rate 16bit):
Output Level (eQ Flat, 0dB=1Vrms, Load=47k Ohms):
MaSter OUtPUt:
0dB ±2dB
thD (eQ Flat, w/20khz LPF, a-Weighted, Load=47k Ohms):
MaSter OUtPUt:
LESS THAN 0.03% (w/20KHz LPF, A-Weighted)
S/n ratio (eQ Flat, w/20khz LPF, a-Weighted, Load=47k Ohms):
MaSter OUtPUt:
MORE THAN 75dB (w/20KHz LPF, A-Weighted)
©American Audio®
-
-
DV2 USB Instruction Manual Page 17
Download from Www.Somanuals.com. All Manuals Search And Download.
©American Audio® World Headquarters:
6122 S. Easter Ave Los Angeles, CA 90040 USA
Tel: 323-582-3322 Fax: 323-582-3311
Download from Www.Somanuals.com. All Manuals Search And Download.
|