INSTALLATION
OPERATION
MAINTENANCE
782DHV12-00
DHV-150H
DEHUMIDIFYING VENTILATOR
DHV-150H Indoor Air Quality System
Installation, Operation & Service Instructions
10. Optional Parts List.......................................... 17
11. Accessories..................................................... 17
12. Warranty Terms............................................... 18
Table of Contents
1. Specifications ................................................... 1
2. Installation......................................................... 1
2.1 Location ........................................................ 1
2.2 Electrical Requirements ................................ 2
2.3 Condensate Removal.................................... 2
2.4 Ducting ......................................................... 3
2.4A Installing Duct Collars............................. 3
2.4B Ducting for Dehumidification................... 3
2.4C Ducting for Fresh Air .............................. 3
2.4D Constant Airflow Regulator Option.......... 4
2.4E Installation in a basement....................... 4
2.4F Installation in an attic.............................. 4
2.4G Installation with (2) HVAC systems......... 4
2.4H Installation without an HVAC system ...... 4
2.5 Quiet Installation ........................................... 5
3. Operation........................................................... 7
3.1 Humidity/Fan Control Panel.......................... 7
3.2 Ventilation Timer & Humidity Control Panel... 7
3.3 Humidity Control Adjustment ........................ 7
3.4 Fan/Filter Switch........................................... 7
3.5 Ventilation Timer .......................................... 7
3.6 High Efficiency Air Filter ............................... 8
3.7 Low Pressure Control.................................... 8
4. Maintenance...................................................... 9
4.1 Standard Air Filter......................................... 9
4.2 High Efficiency Air Filter ............................... 9
4.3 Fresh Air Return ........................................... 9
5. Service............................................................... 9
5.1 Warranty Notice............................................ 9
5.2 Technical description.................................... 9
5.3 Troubleshooting.......................................... 10
5.4 Refrigerant Charging .................................. 11
5.5 Fan Replacement ....................................... 11
5.6 Compressor/Capacitor Replacement........... 11
5.6A Checking Compressor Motor Circuits..... 11
5.6B Replacing Burned Out Compressor........ 12
5.6C Replacing Compressor-Nonburn Out...... 12
5.7 Remote Controls......................................... 12
5.7A Humidity Control.................................... 12
5.7B Ventilation Timer ................................... 13
5.8 Defrost Thermostat..................................... 13
5.9 Electric Ventilation Damper ........................ 13
5.10 Low Pressure Control ................................ 13
5.11 Condensate Pump Kit ............................... 13
6. Electrical Schematic....................................... 14
7. Pictorial Electrical Diagram............................ 15
8. Service Parts List............................................ 16
9. The DHV-150H................................................. 16
F:\W06\AldesW06\DOCFILES\782DHV-150HInst.doc
Serial No. ________________________________
Purchase Date ____________________________
Dealer's Name ____________________________
Read the installation, operation and maintenance
instructions carefully before installing and using this
unit. Proper adherence to these instructions is essential
to obtain maximum benefit from your DHV-150H
(Dehumidifying Ventilator) Indoor Air Quality System.
1 Specifications
Model: DHV-150H Indoor Air Quality System
Electrical: 110-120 VAC, 12 Amps, 60 Hz, grounded
Capacity: 145 pints/day @ 80°F, 60% RH
Operating Temp. Range: 53°F min., 105°F max.
Air Flow: 400 CFM without external ducting
290 CFM @ .40 IWG external static
Refrigerant Charge: 2 lb., 2 oz. R-22
Duct connections: round 10" & 6” inlets, 10” outlet
Filter Size:
Pleated cloth: 2” X 20” X 24”
High Efficiency: 4” X 20” X 24”
Size (w/o duct collars):
46" long x 25" wide x 20.5 " high
Installed Weight: 145 lb.
2 Installation
2.1 Location
The DHV-150H can be installed in a variety of locations
to meet the owner's needs as listed below. In all cases
keep the following cautions in mind:
·
Install the unit INDOORS IN A SPACE THAT IS
PROTECTED FROM FREEZING AND
FLOODING.
·
Install the unit with space to access the front panel
for maintenance and service. Also allow easy
access to the filter cover panel. DO NOT INSTALL
UNIT WITH THE FRONT PANEL OR FILTER
COVER PANEL INACCESSIBLE.
782DHV150H-10-00
Rev:10/30/2002
Download from Www.Somanuals.com. All Manuals Search And Download.
Ducting the DHV-150H as mentioned in sections 2.4A-
2.4G requires consideration of the following points:
An optional condensate pump kit may be installed if a
lift is required to dispose of the condensate. The cond-
ensate pump kit can be ordered direct from the factory.
See the optional parts list for information on the kit.
Duct Sizing: For total duct lengths up to 25', use a
minimum 10" diameter round or equivalent rectangular.
For longer lengths, use a minimum 12" diameter or
equivalent. Grills or diffusers on the duct ends must not
excessively restrict airflow.
2.4 Ducting
Isolated Areas: Effective dehumidification may require
that ducting be branched to isolated, stagnant areas. Use
8" or larger diameter branch ducting to each of two or
three areas, use 6" or larger to each of four or more
areas.
2.4A Installing Duct Collars
The DHV-150H is equipped with 10” and 6” round inlet
collars and a 10” round exhaust collar. The 10” and 6”
round inlet collars are designed with tabs that fold
inside the filter enclosure of the DHV-150H. The 10”
round exhaust collar is attached to the DHV-150H by
folding the tabs inside the end panel of the DHV-150H.
Connecting to existing HVAC systems: An optional
10" check damper is available from the factory to prevent
reverse flow through the DHV-150H. If the DHV-150H is
ducted to the supply of a high static air handler the check
damper may be placed in the DHV-150H supply duct.
2.4B Ducting for Dehumidification
For the ideal installation, draw air from the central part
of the home and return it to the isolated areas of the
home like the bedrooms, den, utility room, or family
room. The ductwork of the existing heating system can
be used to supply air to the home. If the existing supply
goes to isolated areas of the home, discharge the
supply of the DHV-150H into the supply of the existing
heating system. If the existing heating system
incorporates a central supply, installation of a separate
supply duct from the DHV-150H to each isolated area is
recommended. DO NOT draw air directly from the
kitchen, laundry, or isolated basement. You may draw
air from a basement that is open to the home. All
flexible ducting connected to the DHV-150H should be
UL listed.
2.4C Ducting for Fresh Air
Fresh air can be brought into the structure by
connecting a insulated duct from outside to the 6” DHV-
150H inlet and by turning on the fan switch or activating
the humidity control (on units with the humidity control
panel). Activate the ventilation timer on units with the
ventilating & humidity control panel to bring in fresh air.
Refer to section 3.5 for programming instructions for
the ventilation timer. Advantages of this form of
ventilation include:
1. Outside air is filtered before entering the building.
2. Outside air will be dehumidified before entering if
the DHV-150H is running in dehumidification mode.
3. Drawing air from outside and blowing inside aids in
slightly pressurizing the structure. This helps
prevent dirty and humid air from entering elsewhere.
It also reduces the potential for carcinogenic radon
gas to enter and provides make-up air for open
combustion and exhaust devices like the clothes
drier, fireplace, and water heater.
The inlet of the DHV-150H is the 10” diameter hole in
the filter enclosure of the unit. A 10” round collar is
supplied with the unit to attach to round duct. The duct
may be permanently attached to the collar. A 6” round
collar is provided with the unit to attach to the 6” hole in
the filter enclosure. The 6” collar should be capped if
fresh make-up air is not desired. If fresh make-up air is
desired see section 2.4C.
4. The need for an alternate ventilation device may be
eliminated.
The outlet of the DHV-150H is located on the end of the
unit. A second 10” round collar is supplied with the unit.
Cut and remove the safety grid, then bend the tabs on
the collar inside the hole in the cabinet end.
In cold climates or areas where the outdoor dew point is
low at times, ventilation can be used to dehumidify the
structure. This approach is often more economical than
running the dehumidifier to remove excess moisture
from the structure. For example, in a house that
experiences condensation on the interior surface of the
windows during the winter, increasing the amount of
ventilation will often cure the problem.
A length of 10 feet or more of acoustical flex ducting on
the outlet of the DHV-150H will reduce air noise from
the fan. A length of flexible ducting on all DHV-150H
duct connections is recommended to reduce noise and
vibration transmitted to rigid ductwork in the structure.
An insulated 6" diameter duct is generally sufficient to
provide up to 150 CFM of outside air. Large quantities
of outside air will impact DHV-150H performance
3
Download from Www.Somanuals.com. All Manuals Search And Download.
positively or negatively, depending upon the inside and
outside air conditions. Consult the factory by calling 1-
800-255-7749 for recommendations regarding the use
of higher flows with your specific application.
duct from outside to the 6” collar of the DHV-150H if
you wish to provide optional fresh make-up air.
2.4F Installation in an Attic with an
Existing Forced Air HVAC System
The outside air duct should be connected to the 6”
round collar on the filter enclosure of the unit. The 6”
round collar includes a manual damper. Adjust the
manual damper to provide the desired amount of fresh
air for ventilation. The amount of fresh air should be
based on the size and occupancy of the residence. If
you are unsure of your ventilation air requirements,
consult the factory by calling 1-800-255-7749 for
assistance.
ALWAYS install a catch pan with a drain or float
interrupt for condensate under the DHV-150H in an attic
or condensate may drip down on the ceiling of the living
space below.
Locate a separate return for the DHV-150H in a central
area of the structure. Duct the supply of the DHV-150H
to the air supply of the existing HVAC system. Connect
an insulated duct from outside to the 6” collar of the
DHV-150H if you wish to provide fresh make-up air.
2.4D Constant Airflow Regulator and Vent
Hood Options
2.4G Installation in a Structure with Two
Forced Air HVAC Systems
American ALDES offers the fresh air vent hood and
constant airflow regulators (CAR) to control the amount
of fresh air entering the home. These are used in lieu
of the manual damper in the 6” collar on the main unit.
The CAR, inserted in the vent hood collar,
Attach the DHV-150H return to an independent return
from the upper level. Attach the DHV-150H supply to
the supply of the basement HVAC system. This will
promote circulation of air through the whole structure
from the upper level to the lower level through the
DHV-150H. If the DHV-150H is not connected to both
areas, it will not control the humidity and ventilation of
the entire structure. Connect an insulated duct from
outside to the 6” collar of the DHV-150H if you wish to
provide fresh make-up air.
automatically maintains the desired airflow,
independent of pressure. A CAR is recommended for
installations where the DHV draws return air from a
shared HVAC system return duct, to avoid excessive
ventilation when the HVAC fan cycles on. If the indoor
air return is independent of the HVAC system, the CAR
is not necessary, as the manual damper may be set to
the desired airflow.
2.4H Installation in a Structure with No
Existing Forced Air HVAC System
2.4E Installation in a Basement or Crawl
Space with an Existing Forced Air
HVAC System
When installing the DHV-150H in a structure that does
not have a forced air HVAC system, a single return for
the DHV-150H should be installed in central open area
of the structure. DO NOT locate the return in a
bathroom or a kitchen. The supply of the DHV-150H
should be located in the remote areas of the structure
(such as bedrooms, den, etc.). By ducting this way, the
air inside the structure will circulate through the DHV-
150H to be filtered and dehumidified. 4" diameter duct
is recommended for branches to the bedrooms, 6"
diameter duct is recommended for branches to larger
areas. Refer to section 2.4B for branch duct sizing.
Connect an insulated duct from outside to the 6” collar
of the DHV-150H if you wish to provide fresh make-up
air.
If the structure in which the DHV-150H is to be installed
has an existing forced air HVAC system, utilize the
HVAC system to make the DHV-150H installation
easier.
Basement Installation: Install a separate return for the
DHV-150H in a central area of the structure. Duct the
supply of the DHV-150H to a 10” x 10” x 10”
tee/damper that is 30% open to the basement. Duct the
other side of the tee to the air supply of the existing
HVAC system. Connect an insulated duct from outside
to the 6” collar of the DHV-150H if you wish to provide
optional fresh make-up air.
Crawl Space Installation: Install a separate return for
the DHV-150H in a central area of the structure. Duct
the supply of the DHV-150H to a 10” x 10” x 10”
tee/damper that is 30% open to the crawl space if
desired. Duct the other side of the tee to the air supply
of the existing HVAC system. Connect an insulated
4
Download from Www.Somanuals.com. All Manuals Search And Download.
2.5 Quiet Installation
Remove Shipping Restraints
The compressor is attached to the cabinet with two
cable ties to secure it during shipment. This rigid
attachment is not necessary once the unit is installed
and may cause noise from compressor vibration.
AFTER INSTALLATION, CUT THE CABLE TIES TO
FREE THE COMPRESSOR FROM THE CABINET.
REMOVE THE HORIZONTAL CABINET SUPPORT
TO WHICH THE COMPRESSOR IS ATTACHED. The
ends of the support are notched so that the support can
easily be removed. Cut the strips of metal on each end
and remove the support section from the cabinet. This
will prevent the compressor from transmitting vibration
to the cabinet.
Make sure none of the compressor tubes are pressed
against the cabinet or access panel. Check that the
compressor tubes are centered in the holes where they
pass through the drain pan.
A length of 10 feet or more of acoustical flex ducting on
the outlet of the DHV-150H will reduce air noise from
the fan. A length of flexible ducting on all DHV-150H
duct connections is recommended to reduce noise and
vibration transmitted to rigid ductwork in the structure.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 1: DHV-150H in a Basement With a Forced Air System Incorporating a Central Return
Figure 2: DHV-150H in an Attic with a Forced Air System Incorporating a Central Return
6
Download from Www.Somanuals.com. All Manuals Search And Download.
3.3 Humidity Control Adjustment
3 Operation
Set the humidity control to the desired humidity level
for the home. The dehumidifier will run continuously
until the relative humidity (RH) is reduced to the
humidity control dial setting. Setting the humidity
control to lower RH levels will NOT increase the unit's
dehumidification rate; the unit will simply run longer to
reduce the area's RH to the setting. The DHV-150H
unit (and refrigerant-based dehumidifiers in general)
will reduce a warm space's RH to a lower level than
that of a cool space. It is therefore pointless to set the
humidity control to excessively low levels in cool
rooms; doing so will result in long periods of ineffective
dehumidifier run time.
The DHV-150H can be equipped with various
accessories to enhance its operation. A remote control
panel must be used with the DHV-150H. There are two
remote control panels from which to choose. The
humidity/fan control panel is used to control humidity
and the fan. The ventilation timer and humidity control
panel is used to control ventilation, humidity and the
fan.
3.1 Humidity/Fan Control Panel
See Figure 7: The humidity/fan control panel
automatically controls the humidity of the living space.
The humidity/fan control panel contains an adjustable
humidity control and a fan switch. This panel should be
mounted in a central area of the structure where it can
accurately sense the humidity of the air in the living
space. The panel has a cover that must remain open
to the air within the living space for accurate humidity
sensing.
Quality humidity meters are available from the factory
and are recommended to accurately monitor humidity
levels.
3.4 Fan/Filter Switch
Turning ON the fan/filter switch will cause the central
conditioning unit's internal fan to run continuously,
whether the central conditioning unit is dehumidifying
or not. This function is desirable if the central
conditioning unit is used for air circulation and filtration
to achieve maximum indoor air quality. When the
switch is ON; air will be constantly filtered through the
central conditioning unit and circulated throughout the
house. When the switch is OFF the fan will operate
only when the humidity control calls for
The humidity/fan control panel can be used in
conjunction with the optional fresh air damper. When
used with the optional fresh air damper, the fan/filter
switch will act as a fresh air ventilation control. When
the switch is ON (in this configuration), the fan will run,
the fresh air damper will open, and fresh air will be
filtered and brought into the structure. When the switch
is OFF, the fresh air damper will close and the fan will
operate only when the humidity control calls for
dehumidification. Contact the factory for instructions
on this type of installation.
dehumidification or when the ventilation timer calls for
ventilation.
3.5 Ventilation Timer
3.2 Ventilation Timer and
Humidity Control Panel
The ventilation timer controls the fan and the
motorized fresh air damper. When the ventilation timer
is activated, the central conditioning unit will circulate
the indoor air, and bring in fresh air from outside. The
ventilation timer should be set for the required
ventilation of the residence. The home should be
ventilated with fresh air as suggested by applicable
codes and standards.
See Figure 7: The ventilation timer and humidity
control panel automatically controls both the
ventilation and the humidity of the living space. The
ventilation timer and humidity control panel contains
an adjustable humidity control, a fan switch, and a
ventilation timer. This panel will control the humidity
and allow programmed ventilation of the living space.
This panel works in conjunction with the optional fresh
air damper to provide ventilation.
In cold climates or areas where the outdoor dew point
is low at times, ventilation can be used to dehumidify
the structure. This approach is often more economical
than running the dehumidifier to remove excess
moisture from the structure. For example, in a house
that experiences condensation on the interior surface
of the windows during the winter, increasing the
amount of ventilation will often cure the problem.
This panel should be mounted in a central area of the
structure where it can accurately sense the humidity of
the air in the living space. The panel has a cover that
must remain open to the air within the living space for
accurate humidity sensing.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
The ventilation timer is an electronic timer that
displays the current time. This timer has a battery
backup, so it will not require resetting after a power
outage. Following a prolonged power outage the
display of the timer will flash on and off indicating a
power outage has occurred. The one-minute time
increments of the ventilation timer allow you to
program the ventilation of your home to fit your
schedule.
turn off time for the first program. Set the turn off time
using the 1…7, h, and m buttons in the same way as
described above and continue on to the second
through sixth programs. When setting the ventilation
programs, you can return to the current time display by
sliding the switch in the upper right corner of the timer
to RUN. The slide switch in the upper right must be set
to RUN for the timer to operate with the scheduled
programs.
The ventilation timer has six programs with each
program having one “on” and one “off” event. A
program allows the user to turn the ventilation on at a
certain day and time, then it allows them to turn the
ventilation off at a certain day and time. Each of these
programs can be repeated daily or weekly or during a
specified block of days. All six of the programs operate
independently of each other.
The slide switch in the upper left of the timer is used to
choose between automatic and manual operation of
the timer relay. When the slide switch in the upper left
of the timer is set to AUTO mode, the central
conditioning unit will ventilate when the scheduled
programs call for ventilation. When the slide switch in
the upper left of the timer is set to manual (set to hand
symbol on the right), the operation of the timer is
controlled by the I/O button only. Pressing the I/O
button will switch the ventilation timer between ON
(detent) and OFF (detent). As you press the I/O button,
“ON” or “OFF” will be displayed to the right of the time.
The “ON” or “OFF” to the right of the time will indicate
if the ventilation timer is on or off. The I/O button will
manually override scheduled programs if the timer is
in AUTO mode.
If the timer fails to operate or operates erratically,
check that the control panel receives 24Vac from the
DHV-150H. If 24Vac is present at the control panel,
reset the timer by pressing the reset button at the
bottom center of the timer face. The reset button is the
small recessed button with an R beneath it located
below the 1…7 and h buttons. Press the reset button
in until the display clears. Release the reset button.
The display will reappear as 00:00. Resetting the timer
will clear the time and all program settings. After
resetting the timer follow the instructions below to set
the correct time and ventilation programs.
3.6 High Efficiency Air filter
An optional high efficiency air filter is available for the
DHV-150H. ASHRAE Dust Spot Test Method 52-76
rates this filter 90-95% efficient. This filter is much
more efficient than the standard air filter and is able to
catch much smaller particles that can aggravate
allergies.
The following instructions explain how to set the
ventilation timer. First, set the correct time on the
timer by sliding the switch in the upper right hand
corner of the timer to the clock symbol Å and pressing
the 1…7 (DAY), h (HOUR), and m (MINUTE) buttons.
Remember that this timer operates on a 24-hour
(military time) clock.
The high efficiency air filter is 4 inches thick and
should be installed in the filter enclosure directly
behind the standard air filter (See Figure 7). The
standard air filter will act as a prefilter for the high
efficiency air filter and will prolong the life of the high
efficiency air filter.
Next, set the ventilation time schedule. Slide the
switch in the upper right hand corner to the program
symbol P. “ON” will appear to the right of the time and
the number “1” will appear in the lower right hand
corner of the display. The “1” and “ON” signify the turn
on time for the first program. Press the 1…7 button to
choose the days of the week for this program. You can
choose Mon.-Sun, Mon.-Fri., Sat-Sun, or any single
day of the week. The days chosen are shown along the
top of the display on the ventilation timer. Next press
the h button to set the hour for the start of the
3.7 Low Pressure Control
If the low side refrigerant pressure drops to 15 PSIG,
the low-pressure control opens and shuts off the
compressor and fan. It is an automatically reset control
that will close when the pressure rises to 35 PSIG. Its
primary function is to prevent damage to the
ventilation period. Remember that this timer operates
on a 24-hour clock. Then press the m button to set the
minutes past the hour to start the ventilation. Now, with
the ventilation start time set; press the I/O button. The
word “OFF” should appear to the right of the time and
the number “1” should remain in the lower right hand
corner of the display. The “1” and “OFF” signify the
compressor if a leak develops in the refrigeration
system. It may also open if the unit is A) installed in a
cool area (below 50 F) or B) installed where it is below
40 F and then started. Under these conditions, the unit
will restart within several minutes. Until the unit warms
up, it may repeat the cycle several times.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Maintenance
5 Service
CAUTION: Servicing the DHV-150H with its high
pressure refrigerant system and high voltage
circuitry presents a health hazard which could result
in death, serious bodily injury, and/or property
damage. Only qualified service people should
service this unit.
4.1 Standard Air Filter
The DHV-150H is equipped with a pleated cloth air
filter. This filter should be checked semi-annually.
Operating the unit with a dirty filter will reduce
dehumidifier capacity and efficiency and may cause
the compressor to cycle off and on unnecessarily on
the defrost control.
5.1 Warranty Notice
To access the air filter, remove the filter access panel
from the end of the DHV-150H by unscrewing the two
thumbscrews and sliding the panel to the left until it is
free from underneath the side panel. The filter(s)
should be readily visible and can be removed by
pulling them straight out of the DHV-150H.
Warranty terms are provided at the end of this manual.
Please read the terms before any repair is initiated. If
a warranty repair is required, call the factory first at 1-
800-255-7749 for warranty claim authorization and
technical assistance.
5.2 Technical Description
The pleated cloth filter can generally be vacuumed
clean several times before needing replacement.
Replacement filters can be ordered from the factory or
purchased locally if available. DO NOT operate the
unit without the standard filter or with a less effective
filter than the standard filter. The heat exchange coils
inside the unit could become clogged and require
disassembly to clean.
The DHV-150H uses a refrigeration system similar to
an air conditioner's to remove heat and moisture from
incoming air, and add heat to the air that is discharged
(See Figure 3).
4.2 High Efficiency Air Filter
An optional high efficiency pleated microglass paper
filter is available for the DHV-150H. This filter is rated
as 90%-95% efficient by the ASHRAE Dust Spot test
method 52-76. The high efficiency pleated microglass
paper filter should be used in conjunction with the
standard filter, and placed directly behind the standard
filter.
This filter is able to remove allergy-causing particles
from the airstream. Check the high efficiency air filter
every two years and replace if necessary. The high
efficiency filter has a much larger surface area than
the standard filter, thus the standard filter may need to
be cleaned or replaced several times before the high
efficiency filter requires replacement. Be careful not to
damage the fabric media when handling the high
efficiency pleated paper filter. Do not attempt to clean
the high efficiency pleated paper filter. It should be
replaced when it becomes restrictive (See Figure 7).
Figure 3: Refrigeration System of DHV-150H
Hot, high-pressure refrigerant gas is routed from the
compressor to the condenser coil (See Figure 3). The
refrigerant is cooled and condensed by giving up its
heat to the air that is about to be discharged from the
unit. The refrigerant liquid then passes through a
filter/drier and capillary tubing, which causes the
refrigerant pressure and temperature to drop. It next
enters the evaporator coil where it absorbs heat from
the incoming air and evaporates. The evaporator
operates in a flooded condition, which means that all
the evaporator tubes contain liquid refrigerant during
normal operation. A flooded evaporator should
4.3 Optional Fresh Air Return
Check and clean the screen on the outdoor fresh air
return seasonally. The screen may become plugged
during the seasons when there are many particles in
the outdoor air.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
maintain nearly constant pressure and temperature
across the entire coil, from inlet to outlet.
Fan runs with fan switch ON. Fan does not run
with ventilation timer activated.
1. Ventilation timer set to manual & switched OFF.
2. Time not correct on ventilation timer.
3. Defective ventilation timer.
The mixture of gas and liquid refrigerant enter the
accumulator after leaving the evaporator coil. The
accumulator prevents any liquid refrigerant from
reaching the compressor. The compressor evacuates
the cool refrigerant gas from the accumulator and
compresses it to a high pressure and temperature to
repeat the process.
4. Defective fan switch.
Evaporator coil frosted continuously, low
dehumidifying capacity.
1. Dirty air filter(s) or airflow restricted.
2. Excessively restrictive ducting connected to unit.
3. Defrost thermostat loose or defective (Sec. 5.8).
4. Low refrigerant charge
5.3 Troubleshooting
No dehumidification, neither fan nor compressor
run with fan switch and ventilation timer OFF.
1. Unit unplugged or no power to outlet.
2. Humidity control set too high or defective
(Sec. 3.3 & 5.7A)
3. Loose connection in internal or control wiring.
4. Defective Compressor relay.
5. Defective control transformer.
Unit not providing ventilation. Ventilation timer not
operating correctly.
1. If timer is not functioning correctly reset timer
and reprogram (Sec. 3.5).
2. Check control wire connections (check
connections at fresh air damper also).
3. Defective fresh air damper (Sec. 5.9).
4. Defective fan switch.
6. Low pressure Control open (Sec 3.7 & 5.10).
7. Optional Condensate Pump Safety Switch open
(Sec 5.11).
Unit removes some water, but not as much as
expected.
1. Air temperature and/or humidity have dropped.
2. Humidity meter and or thermometer used are
out of calibration.
No dehumidification, compressor does not run but
fan runs with fan switch and ventilation timer OFF
and humidity control turned to ON.
1. Defective compressor run capacitor (Sec. 5.6).
2. Bad connection in compressor circuit (See
Fig. 4).
3. Defective compressor overload (Sec. 5.6A).
4. Defective compressor (Sec. 5.6).
5. Defrost thermostat open (Sec. 5.8).
3. Unit has entered defrost cycle (Sec. 5.8).
4. Air filter dirty (Sec. 4.1 & 4.2).
5. Defective defrost thermostat (Sec 5.8).
6. Low refrigerant charge (Sec. 5.4).
7. Air leak such as loose cover or ducting leaks.
8. Defective compressor (Sec. 5.6).
9. Restrictive ducting (Sec. 2.4).
10. Optional Condensate Pump Safety Switch open
(Sec 5.11).
Fan runs with fan switch and ventilation timer
OFF, but compressor cycles on & off.
1. Low ambient temperature and/or humidity
causing unit to cycle through defrost mode.
2. Defective compressor overload (Sec. 5.6A).
3. Defective compressor (Sec. 5.6).
4. Defrost thermostat defective (Sec. 5.8).
5. Dirty air filter(s) or airflow restricted.
6. Low refrigerant charge, causing defrost control
to cycle.
Unit Test to determine problem:
1. Detach field control wiring connections from
main unit.
2. Connect the yellow and green pigtails from the
main unit together; only the fan should run.
Disconnect the wires.
3. Connect the yellow and blue pigtails from the
main unit together; the compressor and fan
should run.
7. Bad connection in compressor circuit.
4. If these tests work, the main unit is working
properly. You should check the control panel and
field control wiring for problems next.
5. Remove the control panel from the mounting box
and detach it from the field installed control
wiring. Connect the blue, yellow, and green wires
from the control panel directly to the
corresponding colored pigtails on the main unit.
Leave the violet, white and red wires
disconnected!
Fan does not run with fan switch in either
position. Fan does not run with ventilation timer
activated. Compressor runs briefly but cycles on &
off with humidity control turned to ON.
1. Loose connection in fan circuit (See Fig. 4).
2. Obstruction prevents fan impeller rotation.
3. Defective fan.
4. Defective fan relay.
5. Defective fan capacitor.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Turn on the fan switch; the fan should run. Turn
off the fan switch.
7. Turn on the humidity control; the compressor and
fan should run.
8. If these tests work, the problem is most likely in
the field control wiring.
2. Plug in the unit and turn the humidity control to ON.
Check for 110 volts from compressor terminal R to
overload terminal 3 using an AC voltmeter. If
voltage is present, go to step 3. If no voltage, there
may be a loose connection in the compressor
circuit. Test each component for continuity. See
the appropriate section if a defect is suspected.
5.4 Refrigerant Charging
3. Unplug the unit, and then disconnect the red and
yellow wires from compressor terminals R & S.
Using an ohmmeter check continuity between the
points listed below.
If the refrigerant charge is lost due to service or a leak,
a new charge must be accurately weighed in. If any of
the old charge is left in the system, it must be
recovered before weighing in the new charge. Refer to
the unit nameplate for the correct charge weight and
refrigerant type.
4. Compressor terminals C and S:
No continuity indicates an open start winding. The
compressor must be replaced. Normal start
winding resistance is 3 to 7 ohms.
5.5 Fan Replacement
5. Compressor terminals C and R:
No continuity indicates an open run winding. The
compressor must be replaced. Normal run winding
resistance is .5 to 2 ohms.
The motorized impeller is a unitary assembly
consisting of the motor and impeller. If defective, the
complete assembly must be replaced.
6. Compressor terminal C and overload terminal 1:
1. Unplug the power cord.
No continuity indicates a defective overload lead.
2. Remove the cabinet access panel.
3. Remove the screw attaching the fan support
bracket to the base.
7. Overload terminals 1 and 3:
If there is no continuity, the overload may be
tripped. Wait 10 minutes and try again. If there is
still no continuity, it is defective and must be
replaced.
4. Disconnect the fan leads inside the electric box.
5. Push up on the inlet ring and pull the fan and fan
support bracket to the right, then up and out of
the unit.
6. Remove the defective fan from the bracket and
replace with new fan.
7. Reassemble the new fan by reversing the above
procedure.
8. Compressor terminal C and compressor case:
Continuity indicates a grounded motor. The
compressor must be replaced.
9. Disconnect the wires from the run capacitor. Set the
ohmmeter to the Rx1 scale. The capacitor is shorted
and must be replaced if continuity exists across its
terminals. If there is no needle movement with the
meter set on the Rx100000 scale, the capacitor is
open and must be replaced.
5.6 Compressor/Capacitor
Replacement
This compressor is equipped with a two terminal
external overload and a run capacitor, but no start
capacitor or relay (See Figure 4).
10. Reconnect the wires to the compressor and
capacitor. Plug in and turn on the unit. If the
compressor fails to start, replace the run capacitor.
CAUTION-ELECTRICAL SHOCK HAZARD: Electrical
power must be present to perform some tests. These
tests should be performed by a qualified service
person.
11. If the unit still does not start, adding a hard-start kit
(relay & capacitor) will provide greater starting
torque. If this doesn't work, the compressor has an
internal mechanical defect and must be replaced.
5.6A Checking Compressor Motor Circuits
Perform the following tests if the fan runs but the
compressor does not with the fan switch and
ventilation timer OFF and the humidity control ON.
5.6B Replacing a Burned Out Compressor
The refrigerant and oil mixture in a compressor is
chemically very stable under normal operating
conditions. However, when an electrical short occurs
1. Unplug the unit; remove the cabinet side and the
electrical connection cover on the compressor top.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
in the compressor motor, the resulting high
temperature arc causes a portion of the refrigerant oil
mixture to break down into carbonaceous sludge, a
very corrosive acid, and water. These contaminants
must be carefully removed otherwise even small
residues will attack replacement compressor motors
and cause failures.
7. Evacuate the system with a good vacuum pump
and accurate vacuum gauge. Leave the pump
on the system for at least an hour.
8. Operate the system for a short period of time,
monitoring the suction pressure to determine that
the suction filter is not becoming plugged.
Replace the suction filter/drier if pressure drop
occurs. If a severe running burn out has
The following procedure is effective only if the system
is monitored after replacing the compressor to insure
that the clean up was complete.
occurred, several filter/driers may have to be
replaced to remove all of the acid and moisture.
1. This procedure assumes that the previously
listed compressor motor circuit tests revealed a
shorted or open winding.
NOTE: NEVER use the compressor to evacuate
the system or any part of it.
5.6C Replacing a Compressor, Nonburn
Out
2. Remove and properly dispose of the system
charge. DO NOT vent the refrigerant or allow it
to contact your eyes or skin.
Remove the refrigerant from the system. Replace the
compressor and liquid line filter/drier. Charge the
system to 50 PSIG and check for leaks. Remove the
charge and weigh in the refrigerant quantity listed on
the nameplate. Operate the system to verify
performance.
3. Remove the burned out compressor. Use rubber
gloves if there is any possibility of contacting the
oil or sludge.
4. To facilitate subsequent steps, determine the
type of burn out that occurred. If the discharge
line shows no evidence of sludge and the
suction line is also clean or perhaps has some
light carbon deposits, the burn out occurred
while the compressor was not rotating (standing
burn out). Contaminants are therefore largely
confined to the compressor housing. A single
installation of liquid and suction line filter/driers
will probably clean up the system.
5.7 Remote Controls
Devices mounted on a panel that is remote from the
unit control the DHV-150H. You may or may not have
the devices listed below depending on the model of
the remote control panel that you purchased. If the
DHV-150H fails to operate as desired, always check
the settings of the controls to insure that they are
correct. Check that the controls are receiving 24Vac
from the DHV-150H. Check the connections between
the DHV-150H, the control panel, and the field control
wiring.
If sludge is evident in the discharge line, it will
likely be found in the suction line. This indicates
the compressor burned out while running
(running burn out). Sludge and acid have been
pumped throughout the system. Several
5.7A Humidity Control
changes of the liquid and suction filter/driers will
probably be necessary to cleanse the system.
The humidity control is an adjustable switch that closes
when the relative humidity of the air in which it is
located rises to the dial set point. It opens when the
RH drops 4 to 6% below the set point. If the DHV-
150H does not run, try turning the humidity control
clockwise until it reaches the stop and the knob pointer
points at “Max Dry” (see back of control panel cover.)
5. Correct the system fault that caused the burn
out. Consult the factory for advice.
6. Install the replacement compressor with a new
capacitor and an oversized liquid line filter.
In a running burn out, install an oversized
suction line filter/drier between the accumulator
and compressor. Thoroughly flush the
accumulator with refrigerant to remove all
trapped sludge and to prevent the oil hole from
becoming plugged. A standing burn out does not
require a suction line filter/drier.
The DHV-150H is equipped with an automatic defrost
mechanism. If the DHV-150H operates in conditions
that develop frost on the evaporator, it will sense the
frost build-up and automatically defrost the evaporator.
The DHV-150H may not appear to be operating
correctly during the defrost sequence, but once the
defrost sequence is completed, the DHV-150H will
resume dehumidifying.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
damper motor or damage to the motor may result. DO
NOT force the blade of the damper by hand or damage
to the damper motor may result.
5.7B Programmable Ventilation Timer
The ventilation timer controls the fan and the motorized
fresh air damper. When the ventilation timer is
activated, the central conditioning unit will circulate the
indoor air, and bring in fresh air from outside. The
ventilation timer should be set for the required
ventilation of the residence. The home should be
ventilated with fresh air as suggested by applicable
codes and standards.
If the electric ventilation damper fails to operate:
1. Check that the wiring is correct and that voltage is
present at the damper motor.
2. Check for any obstruction inside the damper.
If the electric ventilation damper fails to operate after
performing these checks, it must be replaced.
If the DHV-150H fails to ventilate as expected, check
that the time on the timer is correct. For the timer to
carry out the program schedule, the slide switch in the
upper left corner on the timer must be set to “AUTO”.
The slide switch in the upper right corner of the DHV-
150H must be set to “RUN”. Also check the programs on
the timer to be sure that the timer is calling for
ventilation at the correct times. If the timer fails to
operate or operates erratically, reset the timer; see
section 3.5 of this manual.
5.10 Low Pressure Control
If the low side refrigerant pressure drops to 15 PSIG, the
low-pressure control opens and shuts off the compressor
and fan. It is an automatically reset control. It will close
when the refrigerant pressure rises to 35 PSIG. Its
primary function is to prevent damage to the
compressor if a leak develops in the refrigeration
system. It may also open if the unit is A) installed in a
cool area (below 50 F) or B) installed where it is below
40 F and then started. Under these conditions, the unit
will restart within several minutes. Until the unit warms
up, it may cycle several times.
5.8 Defrost Thermostat
The defrost thermostat is attached to the refrigerant
suction tube between the accumulator and the
compressor. It will automatically shut the compressor off
if the low side refrigerant temperature drops due to
excessive frost formation on the evaporator coil. The
fan will continue to run, causing air to flow through the
evaporator coil and melt the ice. When the ice has
melted, the evaporator temperature will rise and the
thermostat will restart the compressor.
5.11 Condensate Pump Kit
An optional condensate pump kit is available from the
factory for use with the DHV-150H. Condensate is
automatically pumped to a remote location when the
water level in the pump's reservoir rises to close the
float switch.
The pump also contains a safety float switch. The
white leads from this switch extend from beneath the
pump cover. This switch should be installed in series
with the field wire that connects the blue (#5) lead from
the DHV-150H to the blue (#5) lead on the control
panel.
5.9 Electric Ventilation Damper
The ventilation timer controls the electric ventilation
damper. The damper will open when the ventilation
timer is activated to allow fresh air into the structure
through the 6” diameter fresh air inlet duct. The electric
ventilation damper will remain closed when the
ventilation timer is not activated to prevent over-
ventilating the structure when the unit is dehumidifying
or recirculating the indoor air.
If the pump fails, this switch opens the compressor
control circuit and stops water production before the
reservoir overflows. The DHV-150H will continue to
ventilate or circulate air as normal, but will not
dehumidify until this switch closes.
The electric ventilation timer operates on 24 Vac from
the control circuit. DO NOT connect high voltage to the
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 4. Electric Schematics of the DHV-150H
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 5: Pictorial Electrical Diagrams of DHV-150H
15
Download from Www.Somanuals.com. All Manuals Search And Download.
SERVICE PARTS LIST: DHV-150H Indoor Air Quality System
ITEM
PART NO.
AL98996
4017777
4023645
QTY.
DESCRIPTION
Air Filter, Pleated Cloth
1
2
3
1
2
1
Capillary Tube, .059" X .124" X 32.00" (not shown)
Compressor Service Kit, Carlyle (EBA120111A)
(Includes Compressor, Capacitor & Overload)
Compressor Overload (EBA120111A) (not shown)
Compressor Relay, SPST, 24 Vac, 30A
Compressor Run Capacitor, 30 MFD
Condenser Coil
Defrost Thermostat,
Defrost Thermostat Mounting Clip, (item 8) (not shown)
Evaporator Coil
4
5
6
7
8
4022595
4022484
4022740
4022563
4021470
4021648
4022563
4024270
4020924
4024360
4022593
4021626
4023875
4023928
4022219
4020623
4022487
4024359
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
9
10
11
12
13
14
15
16
17
18
19
20
Fan
Fan Relay, SPDT, 24 Vac, 15A
Fan Run Capacitor, 16MFD
Filter/Drier
Hose, Drain Pan, .56” ID x 8'
Inlet Collar, 10” Galvanized Steel
Inlet Collar, 6” Galvanized Steel with Damper
Low Pressure Control
Outlet Collar, 10” Galvanized Steel
Transformer, 120/24 Vac, 40 VA
Wiring Diagram (on Cover) (not shown)
Figure 6: The DHV-150H
16
Download from Www.Somanuals.com. All Manuals Search And Download.
OPTIONAL PARTS LIST: DHV-150H Indoor Air Quality System
ITEM
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
PART NO.
AL98995
AL99027
AL99006
4024155
4024125
4023660
AL23040
4024153
4021495
4024150
4024122
4020554
4022486
AL99982
AL22023
AL16370
AL16371
AL16372
AL16373
QTY.
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
DESCRIPTION
Air Filter, High Efficiency, Pleated Microglass Paper, 90%-95%
Check Damper, 10" Diameter (not shown)
Condensate Pump Kit, External
Control Panel Assembly, Humidity/Fan
Control Panel Assembly, Ventilation Timer & Humidity
Controller, Humidity
Duct Damper, 6” Diameter, Electrically Actuated (not shown)
Cover for Items 28 & 29 (not shown)
Knob, Black, .25” shaft
Instructions, Humidity/Fan (not shown)
Instructions, Ventilation Timer & Humidity (not shown)
Switch, Black, SPDT, ON/OFF
Timer, 7-Day, 24 Vac, Programmable
Optional External Insulation Kit (not shown)
6” Vent Hood (not shown)
6” CAR (Constant Airflow Regulator) 75 CFM (not shown)
6” CAR, 100 CFM (not shown)
41
42
43
1
1
1
6” CAR, 125 CFM (not shown)
6” CAR, 150 CFM (not shown)
Figure 7: Accessories
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Limited Warranty
American ALDES Ventilation Corporation warrants to the original end user of the Dehumidifier or Dehumidifying
Ventilator model referred to below, to be free from manufacturing defects. It is limited to the original end-user and
may not be assigned or transferred.
First Year Warranty: If the product exhibits a defect in materials or workmanship within one (1) year after purchase,
American ALDES, at its option, will repair or replace the unit free of charge for materials and labor.
Second through Fifth Year: American ALDES warrants that for a period of five (5) years, the condenser, evaporator,
and compressor of the unit will operate free of defect in materials or workmanship, or American ALDES, at its option
will repair or replace the defective parts, provided that labor and transportation costs are borne by the end-user.
Proof of purchase: The end-user must provide a dated proof of purchase upon request, by copy of invoice from
American ALDES, or the installing dealer.
End-User Responsibilities: Warranty service must be performed by a Servicer authorized by American ALDES
Ventilation Corporation. If the end-user is unable to locate or obtain warranty service from an authorized Servicer, he
should call American ALDES Ventilation Corporation (1-800-255-7749) to arrange for covered warranty service.
Warranty service will be performed during normal business hours.
The end-user is responsible for normal care, including normal maintenance, filter replacement, as outlined in the
installation and operating instructions. This warranty applies only to residential applications and does not cover any
defect or malfunction, etc., resulting from misuse, abuse, lack of maintenance, corrosion, freezing, modification,
unauthorized or improper repair or installation, accident, acts of nature, or any other cause beyond American ALDES
Ventilation Corporation’s reasonable control.
Limitations and Exclusions: If any American ALDES Dehumifier/Dehumidifying Ventilator part is repaired or
replaced, the new part shall be warranted for only the remainder of the original warranty period applicable thereto. All
warranty periods shall be extended by the period of time, if any, that the unit is out of service while awaiting covered
warranty service.
Upon the expiration of the written warranty applicable to the Dehumidifier/Dehumidifying Ventilator or any part
thereof, all other warranties implied by law, including merchantability and fitness for a particular purpose, shall also
expire.
American ALDES makes no express warranties, except for those that are set forth herein and shall not be liable for
any incidental, special, or consequential damages, including without limitation water damage (the end-user should
take precautions against same), lost profits, delay, or loss of use or damage to any real or personal property, with
respect to the American ALDES products covered by this warranty. American ALDES complete liability and the
owner’s exclusive remedy are limited to repair or replacement according to the terms stated herein.
No person is authorized to change the warranty in any way or grant any other warranty unless such changes are made
in writing and signed by an officer of American ALDES Ventilation Corporation.
Some states do not allow limitations of how long an implied warranty lasts, and some do not allow the exclusion or limitation of
incidental or consequential damages, so one or both of these limitations by not apply to you.
Legal Rights: This warranty gives you specific legal rights, and you may have other rights, which vary from state to state.
American ALDES Ventilation Corporation, 4537 Northgate Ct. Sarasota, FL 34234 (800) 255-7749
Model:
Unit Serial No._____________________________________
Installed by:____________________________________
Date:____________________________________________
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Date
Service Notes
19
Download from Www.Somanuals.com. All Manuals Search And Download.
|