ACCESSORIES
MANUAL PART NUMBER: 400-0115-001
PRODUCT REVISION: 1
TNP100AUUN
Tilt ‘N Plug™ Interconnect Box
FOR AUSTRALIA
USER'S GUIDE
Download from Www.Somanuals.com. All Manuals Search And Download.
ACCESSORIES
cause serious injury because of the sharp
edges inside of the TNP100AU.
PRECAUTIONS / SAFETY WARNINGS
1
Please read this manual carefully before using your
TNP100AU Interconnect Box. Keep this manual
handy for future reference. These safety instructions
are to ensure the long life of your TNP100AU and to
prevent fire and shock hazard. Please read them
carefully and heed all warnings.
·
·
Do not place heavy objects on top of the
TNP100AU. Do not use excessive force to
push down on the top of the unit.
To turn off the main power, disconnect the
power cord, which powers the power socket
on the TNP100AU pop up panel only. The
power outlet socket should be installed as
near to the equipment as possible, and
should be easily accessible.
1.1 GENERAL
·
·
Unauthorized personnel shall not open the
unit since there are high-voltage
components inside.
·
·
We recommend using wall outlets with a
Ground Fault Circuit Interrupter (GFCI) for
maximum protection.
Qualified ALTINEX service personnel, or
their authorized representatives must
perform all service.
Install all cables according to the
instructions. Do not force or pull out any
cable or power cord that is attached to the
TNP100AU Interconnect Box.
1.3 CLEANING
Surfaces should be cleaned with a dry cloth.
·
Never use strong detergents or solvents,
such as alcohol or thinner. Do not use a wet
cloth or water to clean the unit.
1.4 FCC / CE NOTICE
·
·
This device complies with part 15 of the
FCC Rules. Operation is subject to the
following two conditions: (1) This device
may not cause harmful interference, and (2)
this device must accept any interference
received, including interference that may
cause undesired operation.
1.2 INSTALLATION
·
For best results, place the TNP100AU
Interconnect Box in a dry area away from
dust and moisture.
·
To prevent fire or shock, do not expose this
unit to rain or moisture. Do not place the
TNP100AU Interconnect Box in direct
sunlight, near heaters or heat radiating
appliances, or near any liquid. Exposure to
direct sunlight, smoke, or steam can harm
internal components.
This equipment has been tested and found
to comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide
reasonable protection against harmful
interference when the equipment is
operated in a commercial environment. This
equipment generates, uses, and can radiate
radio frequency energy and, if not installed
and used in accordance with the instruction
manual, may cause harmful interference to
radio communications. Operation of this
equipment in a residential area is likely to
·
·
Handle the TNP100AU Interconnect Box
carefully. Dropping or jarring can damage
internal components.
Never place fingers inside the opening on
each side of the unit. This action could
2
Download from Www.Somanuals.com. All Manuals Search And Download.
ACCESSORIES
cause harmful interference in which case
the user will be required to correct the
interference at his own expense.
TECHNICAL SPECIFICATIONS
3
FEATURES/
TNP100AU
TNP100AU
DESCRIPTION
·
Any changes or modifications to the unit not
expressly approved by ALTINEX, Inc. could
void the user’s authority to operate the
equipment.
GENERAL
Front Panel
Standard
Cable end
under table
Faceplate
Configuration
Connectors
ABOUT YOUR TNP100AU
2
1 plug with 6ft
cord
1 Australian outlet with a 5A
circuit breaker
The TNP100AU is designed for installation into a
conference room table. The Tilt ‘N Plug™
Interconnect Box (TNP100AU) provides a means of
connecting audio, video, control, and computer video
sources into a presentation system. It is ideal for use
together with ALTINEX computer video interfaces.
The Tilt ‘N Plug™ Interconnect Box can either pop up
and “tilt” to a raised position to provide access to the
connectors or it can be lowered into a table when not
in use. A pneumatic shock inside the TNP100AU’s
tower type construction applies pressure to the panel
mechanism, making it easy to raise and secure the
unit firmly in an open position.
1 receptacle
Power
Computer Video
1 15-pin HD-F 1 15-pin HD-F
Composite Video 1 Yellow RCA-F 1 Yellow RCA-F
Audio, left, right
1 Black, 1 Red 1 Black, 1 Red
RCA-F RCA-F
1 3.5 mm stereo 1 3.5 mm stereo
female plug female plug
1 RJ-11 F (6- 1-RJ-11-M (6-
position) position)
1 RJ-45-F (8- 1 RJ-45-M (8-
Audio
Telephone
Network
position)
position)
The Tilt ‘N Plug™ Interconnect Box has one input
plate on the front panel of the unit. The standard
plate offers Computer Video (15-pin HD); Composite
Video (RCA), Audio (RCA), Computer Audio (Stereo
Mini), Modem (RJ-11), 9-pin D-type RS-232 and
Network (RJ-45) input connections. All signals are
passed through to a set of female connectors or
Control
1 DB-9 F
1 DB-9 F
Table 1. TNP100AU General
Mechanical
Width (inches)
Height (closed)
Height (opened)
Depth (inches)
Finish
TNP100AU
6.05in (154mm)
4.79in (122mm)
8.05in (205mm)
7.560 (192mm)
Flat Black
cables.
Several optional connectors can be
substituted for the standard set of connectors.
Operation
The Tilt ‘N Plug™ Interconnect Box is designed for
use with tables ranging from one to three inches
thick. It offers an optional mounting bezel to secure
the unit flush with the table’s surface. The Tilt ‘N
Plug™ comes in a standard matte black color. The
top of the unit can be finished to match the table or it
can be painted another color. This is available on a
custom per order basis at an additional charge.
T° Operating
T° Maximum
Humidity
10°C-35°C
50°C
90% non-condensing
Table 2. TNP100AU Mechanical
Power
Power Rating (pass
through connector)
TNP100AU
220-240V~5A,
50/60Hz
Table 3. TNP100AU Electrical
3
Download from Www.Somanuals.com. All Manuals Search And Download.
ACCESSORIES
TNP100AU DIMENSIONS
Diagrams: 1A, 1B, 1C, & 1D
4
4
Download from Www.Somanuals.com. All Manuals Search And Download.
ACCESSORIES
DESCRIPTION DIAGRAM
Diagram 2: Label of Product
5
APPLICATION DIAGRAM
6
5
Download from Www.Somanuals.com. All Manuals Search And Download.
ACCESSORIES
Diagram 3: Application
6
Download from Www.Somanuals.com. All Manuals Search And Download.
ACCESSORIES
Diagram 4: Final Installation
7
Download from Www.Somanuals.com. All Manuals Search And Download.
ACCESSORIES
Diagram 5: Table Cutout Requirements
8
Download from Www.Somanuals.com. All Manuals Search And Download.
ACCESSORIES
Step 5. Connect the appropriate cables with the
correct input connectors. There are two
RCA audio connectors on the front panel
of the TNP100AU. The black connector is
known as audio left, whereas the red
connector is called audio right. There is
also an RCA video connector, which is
yellow in color. The network connection is
red. In addition, the telephone or data
connection is gray.
INSTALLATION
6
Step 1. Cut an opening into the table’s surface.
Refer to diagram 5 on page 8 of the
manual for table cutout requirements.
Note: The table can be 3 inches or thinner
in thickness. Always confirm dimensions
before cutting to insure that specifications
have not changed.
Step 2. Insert the TNP100AU into the opening in
the table.
Step 6. Once you have applied power and
connected the proper cables on the bottom
of the unit, you may raise the unit. To raise
the TNP100AU into position, lift the top by
pulling upward at the notch in the top plate.
Step 3. Place the support brackets under the table
and place them between the support
mount grooves on the side of the
TNP100AU unit. Attach the brackets to the
groove at the desired height and secure
them to the bottom of the table using the 6-
32 nut. There are two support brackets,
one for each side of the unit. (See Figure
1)
Step 7. To lower the unit, push on the top of the
TNP100AU until it fits into place.
For more information, please refer to the FAQ
Section or the Troubleshooting Guide.
Figure 1: Attachment of the TNP100AU to a
table using support brackets and set screws
Step 4. Secure the cables by using the provided
cable clamp (See Figure 2). Pass the
power cord from the bottom of the housing
and attach it to the table using the cable
clamp supplied with the TNP100AU unit.
Do not keep the cord too tight or too loose
(See Diagram 4, page 7).
Figure 2: Cable Clamp
9
Download from Www.Somanuals.com. All Manuals Search And Download.
ACCESSORIES
FREQUENTLY ASKED QUESTIONS (FAQ)
8
OPERATION
7
No: Question
Answer
7.1 HOW TO RELEASE AND REPLACE THE GAS
SPRING
1
Why are the
VGA connectors reliable.
Female cables are more
female on both
ends of the
cables?
Why is there a
DB-9 connector? compatible with RS-232
serial communication.
What happens if The unit will not stay
the spring
breaks?
What do I do if
the TNP100AU
won’t stay open?
How much room The unit is 4.5 inches
is taken up on deep maximum below
the underside of the table; to this
the table? dimension add about 2.5
To replace the spring, push up, and turn the
knob in the center on the bottom of the
TNP100AU by 90 degrees, thereby releasing
the gas spring.
2
3
4
5
The DB-9 connector is
Unscrew the knob, and then unscrew the gas
spring itself from the TNP100AU. Replace the
gas spring with a new one by screwing it in,
and then replacing the knob.
open.
Replace the gas spring.
Call ALTINEX for service
information.
Re-engage the new gas spring by pushing
up, and turning the knob by 90 degrees. After
you have finished this step, you have
completed the installation.
Under normal conditions the gas spring will
last up to five years.
inches for cable
clearance.
6
7
What if my table Then the area under the
is thicker than 3
inches?
table near the
TNP100AU must be
reduced to 3 inches of
thickness.
Are cables
Consider using
available for
connecting a
MS8126CA (3ft) or
MS8156CA (6ft) for VGA
PC/laptop to the connection.
TNP100AU
available?
8
Does ALTINEX
honor any
Anything modified by
non-ALTINEX personnel
warranty on field is not covered by
modifications? warranty.
CABLES AND ACCESSORIES
9
10
Download from Www.Somanuals.com. All Manuals Search And Download.
ACCESSORIES
OPTIONAL CUSTOM
CONNECTORS
Blank Connector (Snap-in and
15-pin location)
BNC Female
4-pin Mini-DIN
Model No.
Description
VGA MALE TO MALE (HD-15)
HIGH RESOLUTION CABLE
xx = available length of 3ft, 6ft,
15ft, 25ft, ö50ft, ö75ft, ö100ft,
& ö150ft
CB37xxMR
6-pin Mini-DIN
VGA MALE TO FEMALE (HD-
15) HIGH RESOLUTION
CABLE
öIndicates super high resolution cable type
xx = available length of 3ft, 6ft,
15ft, 25ft, ö50ft, ö75ft, ö100ft,
& ö150ft
CB39xxHR
SUPER HIGH RESOLUTION
PLENUM-FLEX MULTI-
CHANNEL COAX CABLE
VGA MALE TO VGA MALE
(HD-15)
xxx = available length of 3ft,
6ft, 15ft, 25ft, 50ft, 75ft, 100ft,
150ft, 200ft, & 250ft
CB5000PL-
5VMxxx5VM
SUPER HIGH RESOLUTION
PLENUM-FLEX MULTI-
CHANNEL COAX CABLE
VGA MALE TO VGA FEMALE
(HD-15)
xxx = available length of 3ft,
6ft, 15ft, 25ft, 50ft, 75ft, 100ft,
150ft, 200ft, & 250ft
CB5000PL-
5VMxxxx5VF
SUPER HIGH RESOLUTION
PLENUM-FLEX MULTI-
CHANNEL COAX CABLE
VGA MALE TO VGA MALE
(HD-15)
xxx = available length of 3ft,
6ft, 15ft, 25ft, 50ft, 75ft, 100ft,
150ft, 200ft, & 250ft
CB5100PL-
5VMxxxx5VM
SUPER HIGH RESOLUTION
PLENUM-FLEX MULTI-
CHANNEL COAX CABLE
VGA MALE TO VGA FEMALE
(HD-15)
xxx = available length of 3ft,
6ft, 15ft, 25ft, 50ft, 75ft, 100ft,
150ft, 200ft, & 250ft
CB5100PL-
5VMxxxx5VF
11
Download from Www.Somanuals.com. All Manuals Search And Download.
ACCESSORIES
event that an ALTINEX product needs to be
returned, please follow the policies below:
TROUBLESHOOTING GUIDE
10
The TNP100AU supplied unit was carefully tested
and no problems were detected; however, we
would like to offer the following suggestions:
Altinex will accept all product returns for a period
of 30 days from authorized ALTINEX dealers in
an unopened package.
·
If there is no power, check to see if the 5A
circuit breaker is tripped.
If a product has been opened, the restocking
fees will apply. For the restocking fee, please
contact an ALTINEX Sales Representative.
·
Please make sure that the highest quality of
video, audio, network, and telephone cables or
connectors is used.
If the product is in your possession for more than
30 days, the restocking fees will apply.
·
Make sure that no cable or power cord is
damaged or pinched. If there has been
damage, then do not use the TNP100AU unit.
Immediately contact the ALTINEX Customer
Service Department to have the unit repaired.
Altinex will not accept any returns on cables or
custom products.
If your product is in warranty and needs service,
contact the ALTINEX Sales Department for an
RMA (Return Material Authorization). Products
returned without an RMA number may
experience a delay in service.
ALTINEX POLICY
11
If your product is out of warranty and needs
service, contact the ALTINEX Sales Department
for an RMA (Return Material Authorization).
Products returned without an RMA number may
experience a delay in service. The service
charges will be quoted to you before the actual
repairs are done.
11.1 LIMITED WARRANTY
ALTINEX warrants that its products and cables
are free from defects in materials under normal
use and service. This warranty is limited to
repairing at company’s factory any part or parts
of the product, which upon company’s
examination shall disclose to be, thus defective.
Products considered defective should be returned
to company with transportation charges pre-paid
within 2 years (90 days for cables) from date of
shipment to the purchaser. The warranty is
expressly instead of all other warranties
expressed or implied. ALTINEX neither assumes
nor authorizes any other person to assume for it
any other liability concerning the sale of the
products. This warranty shall not apply to any
product that shall have been repaired or altered
outside of company’s factory in any way so as, in
its judgment, to affect its stability or reliability, or
that has been subject to misuse, negligence, or
accident.
11.3 CONTACT INFORMATION
Phone:
Fax:
714-990-2300
714-990-3303
11.2 RETURN POLICY
It is very important to ALTINEX that you receive
all products that you have ordered and that this
product meets your expectations. In the unlikely
12
Download from Www.Somanuals.com. All Manuals Search And Download.
|