ENGLISH
Contents
Sound Setting
Operating Instructions
Adjusting Balance (Between Left and Right)/
Fader (Between Front and Rear)/Defeat...... 14
Adjusting and Storing the built-in
WARNING
WARNING..................................................3
CAUTION ...................................................3
PRECAUTIONS .........................................3
Crossover ..................................................... 14
Recalling the Stored built-in
Crossover Settings ....................................... 14
Equalizer Presets ............................................. 15
Adjusting and Storing the Equalizer Curve .... 15
Recalling the Stored Equalizer Curve ............. 15
About Time Correction ................................... 16
Bass Focus ...................................................... 16
Adjusting and Storing the Time Correction .... 18
Recalling the Stored Time Correction
Getting Started
Turning Power On and Off ............................... 6
Initial System Start-Up ..................................... 6
Setting Time ...................................................... 6
Opening and Closing the Movable Display ...... 6
Display Tilt Adjustment .................................... 6
Adjusting Volume ............................................. 7
Lowering Volume Quickly ................................ 7
Changing the Display Type ............................... 7
Detaching and Attaching the Front Panel ......... 7
Settings ........................................................ 18
Setting the MX Mode ..................................... 18
Other Functions
Displaying the Title/Text................................. 19
Titling Discs/Stations ...................................... 20
Erasing Disc Title/Station Title ....................... 20
Displaying Time.............................................. 20
Blackout Mode On and Off............................. 20
Setting an Amplifier Link
Radio
Changing the Radio Frequencies for each
Country .......................................................... 8
Listening to Radio............................................. 8
Manual Storing of Station Presets .................... 8
Automatic Memory of Station Presets .............. 8
Tuning to Preset Stations .................................. 8
Station Title Search Function............................ 9
Frequency Search Function............................... 9
(CDA-9831 only)......................................... 21
Displaying the External Amplifier Information
(CDA-9831 only)......................................... 21
Setting the Multicolor Illumination
CD/MP3/WMA
(CDA-9831 only)......................................... 22
Changing the Lighting Color of
Playback ............................................................ 9
Playing back a Playlist .................................... 10
Repeat Play ..................................................... 11
M.I.X. (Random Play) .................................... 11
Scanning Programs ......................................... 12
Searching from CD Text ................................. 12
File/Folder Name Search
All the Buttons (CDA-9831 only) ............... 22
Verifying the Software Version ....................... 22
Windows Media and the Windows logo are trademarks, or
registered trademarks of Microsoft Corporation in the United
States and /or other countries.
(concerning MP3/WMA) ............................ 12
Quick Search ................................................... 12
About MP3/WMA .......................................... 12
1-EN
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating Instructions
WARNING
CAUTION
This symbol means important instructions. Failure
to heed them can result in injury or material
property damage.
WARNING
This symbol means important instructions. Failure
to heed them can result in serious injury or death.
HALT USE IMMEDIATELY IF A PROBLEM APPEARS.
Failure to do so may cause personal injury or damage to the
product. Return it to your authorized Alpine dealer or the nearest
Alpine Service Center for repairing.
DO NOT OPERATE ANY FUNCTION THAT TAKES YOUR
ATTENTION AWAY FROM SAFELY DRIVING YOUR
VEHICLE.
DO NOT MIX NEW BATTERIES WITH OLD BATTERIES.
Any function that requires your prolonged attention should only
be performed after coming to a complete stop. Always stop the
vehicle in a safe location before performing these functions.
Failure to do so may result in an accident.
INSERT WITH THE CORRECT BATTERY POLARITY.
When inserting the batteries, be sure to observe proper polarity (+
and –) as instructed. Rupture or chemical leakage from the
battery may cause fire or personal injury.
KEEP THE VOLUME AT A LEVEL WHERE YOU CAN STILL
HEAR OUTSIDE NOISE WHILE DRIVING.
KEEP FINGERS AWAY WHILE THE MOTORIZED FRONT
PANEL OR MOVING MONITOR IS IN MOTION.
Failure to do so may result in personal injury or damage to the
product.
Failure to do so may result in an accident.
MINIMIZE DISPLAY VIEWING WHILE DRIVING.
Viewing the display may distract the driver from looking ahead of
the vehicle and cause an accident.
PRECAUTIONS
Temperature
DO NOT DISASSEMBLE OR ALTER.
Doing so may result in an accident, fire or electric shock.
Be sure the temperature inside the vehicle is between +60°C
(+140°F) and –10°C (+14°F) before turning your unit on.
USE ONLY IN CARS WITH A 12 VOLT NEGATIVE GROUND.
(Check with your dealer if you are not sure.) Failure to do so may
result in fire, etc.
Moisture Condensation
You may notice the CD playback sound wavering due to
condensation. If this happens, remove the disc from the player
and wait about an hour for the moisture to evaporate.
KEEP SMALL OBJECTS SUCH AS BATTERIES OUT OF THE
REACH OF CHILDREN.
Swallowing them may result in serious injury. If swallowed,
consult a physician immediately.
Damaged Disc
Do not attempt to play cracked, warped, or damaged discs.
Playing a bad disc could severely damage the playback
mechanism.
USE THE CORRECT AMPERE RATING WHEN REPLACING
FUSES.
Failure to do so may result in fire or electric shock.
Maintenance
DO NOT BLOCK VENTS OR RADIATOR PANELS.
Doing so may cause heat to build up inside and may result in fire.
If you have problems, do not attempt to repair the unit yourself.
Return it to your Alpine dealer or the nearest Alpine Service
Station for servicing.
USE THIS PRODUCT FOR MOBILE 12V APPLICATIONS.
Use for other than its designed application may result in fire,
electric shock or other injury.
DO NOT PLACE HANDS, FINGERS OR FOREIGN OBJECTS
IN INSERTION SLOTS OR GAPS.
Doing so may result in personal injury or damage to the product.
3-EN
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Location
Make sure the CDA-9831/CDA-9830 will not be installed in a
location subjected to:
PRECAUTIONS
Product Cleaning
Use a soft dry cloth for periodic cleaning of the product. For
more severe stains, please dampen the cloth with water only.
Anything else has the chance of dissolving the paint or damaging
the plastic.
•
•
•
•
Direct sun and heat
High humidity and water
Excessive dust
Excessive vibrations
Never Attempt the Following
Correct Handling
Do not grip or pull out the disc while it is being pulled back into
the player by the automatic reloading mechanism.
Do not attempt to insert a disc into the unit when the unit power
is off.
Do not drop the disc while handling. Hold the disc so you will
not leave fingerprints on the surface. Do not affix tape, paper, or
gummed labels to the disc. Do not write on the disc.
CORRECT
CORRECT
INCORRECT
Inserting Discs
Your player accepts only one disc at a time for playback. Do not
attempt to load more than one disc.
Make sure the label side is facing up when you insert the disc.
Your player will automatically eject any disc that is inserted
incorrectly. If the player continues to eject a correctly inserted
disc, push the RESET switch with a pointed object such as a
ballpoint pen.
Disc Cleaning
Fingerprints, dust, or soil on the surface of the disc could cause
the CD player to skip. For routine cleaning, wipe the playing
surface with a clean, soft cloth from the center of the disc to the
outer edge. If the surface is heavily soiled, dampen a clean, soft
cloth in a solution of mild neutral detergent before cleaning the
disc.
Playing a disc while driving on a very bumpy road may result in
skips, but this will not scratch the disc or damage the player.
New Discs
As a protective measure to prevent the CD from jamming, the CD
player will automatically eject discs with irregular surfaces or
inserted incorrectly. When a new disc is inserted into the player
and ejected after initial loading, using your finger, feel around the
inside of the center hole and outside edge of the disc. If you feel
any small bumps or irregularities, this could inhibit proper
loading of the disc. To remove the bumps, rub the inside edge of
the hole and outside edge of the disc with a ballpoint pen or other
such instrument, then insert the disc again.
Disc Accessories
There are various accessories available on the market for
protecting the disc surface and improving sound quality.
However, most of them will influence the thickness and/or
diameter of the disc. Using such accessories can cause the disc to
be out of standard specifications and may create operational
problems. We recommend not using these accessories on discs
played in Alpine CD players.
Center Hole
Center Hole
New
Disc
Bumps
Outside
(Bumps)
Irregular Shaped Discs
Be sure to use round shape discs only for this unit and never use
Transparent Sheet
Disc Stabilizer
any special shape discs.
Use of special shape discs may cause damage to the mechanism.
4-EN
Download from Www.Somanuals.com. All Manuals Search And Download.
On handling Compact Discs (CD/CD-R/CD-RW)
•
•
•
•
•
•
Do not touch the surface.
Do not expose the disc to direct sunlight.
Do not affix stickers or labels.
Clean the disc when it is dusty.
Make sure that there are no bumps around the disc.
Do not use commercially available disc accessories.
Do not leave the disc in the car or the unit for a long
time. Never expose the disc to direct sunlight. Heat
and humidity may damage the CD and you may not be
able to play it again.
To customers using CD-R/CD-RW
•
If a CD-R/CD-RW cannot be played back, make sure the last
recording session was closed (finalized).
Finalize the CD-R/CD-RW if necessary, and attempt playback
again.
•
About media that can be played.
Use only compact discs with the label side showing the CD logo
marks below.
If you use unspecified compact discs, correct performance cannot
be guaranteed.
You can play CD-Rs (CD-Recordable)/CD-RWs (CD-
ReWritable) which have been recorded only on audio devices.
You can also play CD-Rs/CD-RWs containing MP3/WMA
formatted audio files.
•
Some of the following CDs may not play on this unit:
Flawed CDs, CDs with fingerprints, CDs exposed to extreme
temperatures or sunlight (e.g., left in the car or this unit), CDs
recorded under unstable conditions, CDs on which a
recording failed or a re-recording was attempted, copy-
protected CDs which do not conform to the audio CD
industry standard.
•
Use discs with MP3/WMA files written in a format
compatible with this unit. For details, see page 12-13.
About the alphanumeric display of CDA-9830.
•
All English lower case characters are displayed as upper case
on this unit.
•
The alphanumeric display in the following table shows
alphanumeric characters/numbers that may be difficult to
distinguish.
Alphanumeric
Display
0
2
5
6
8
A
B
D
Z
Alphanumeric
Display
G
H
K
M
Q
R
S
5-EN
Download from Www.Somanuals.com. All Manuals Search And Download.
Opening and Closing the Movable Display
Getting Started
Press c.
The movable display will open.
SOURCE/
POWER
DISP/
Rotary
TITLE
B.OUT
encoder
To close the movable display, press c again.
The movable display will close.
•
•
Do not apply shock to the movable display when it is open as it
may result in malfunction of the unit.
The display may be dim during low temperatures and immediately
after turning on the power. The brightness will return to normal as
time elapses.
c
g MENU f MUTE RESET
TILT 98
•
The display will stop at the set tilt angle when closing.
Turning Power On and Off
Caution
Keep hands (or any other object) away from the display while it is
opening or closing to avoid damage or injury. The back of the
movable display will get very warm under normal operating
conditions. This is not a malfunction. Do not touch.
Press SOURCE/POWER to turn on the unit.
The unit can be turned on by pressing any other button except eject
c and TITLE
•
.
Press and hold SOURCE/POWER for at least 2
seconds to turn off the unit.
Display Tilt Adjustment
•
The first time power is turned on, the volume will start from level 12.
Movable display
Initial System Start-Up
Be sure to press the RESET switch when using the unit for the first
time, after installing the CD changer, after changing the car battery, etc.
The movable display may be adjusted to 3 different tilt angles
depending upon user preference.
Turn off the unit power.
1
Press RESET with a ball-point pen or similar
pointed object.
2
Press TILT 98 to adjust the tilt angle of the movable
display.
•
The display will close a half minute after the ignition key is turned
to the OFF position.
Setting Time
•
The adjusted tilt angle of the display is stored in memory. There is
no need to re-adjust the tilt angle when the power is turned back on
.
Press MENU to select SETUP.
1
Caution
Keep hands (or any other object) away from the display while it is
opening or closing to avoid damage or injury. The back of the
movable display will get very warm under normal operating
conditions. This is not a malfunction. Do not touch.
Press g or f to select the CLOCK mode.
2
3
Turn the Rotary encoder to adjust the hours
within 15 seconds.
When the hour has been adjusted, press the
Rotary encoder.
4
Turn the Rotary encoder to adjust the minutes
within 15 seconds.
5
When the setting has been completed, press
MENU to select RETURN.
6
The unit returns to normal mode.
Pressing and holding MENU for at least 2 seconds will
return to normal mode.
•
To synchronize the clock to another clock/watch or radio time
announcement, press and hold the Rotary encoder for at least 2
seconds after setting the "hour." Minutes will reset to 00. If the
display shows over "30" minutes when you do this, the time will
advance one hour.
6-EN
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting Volume
Detaching and Attaching the Front Panel
Detaching
Turn the Rotary encoder until the desired sound is
obtained.
Turn off the unit power.
1
Press
front panel pops out.
(Release) at the upper left side until the
2
Lowering Volume Quickly
Activating the Audio Mute function will instantly lower the volume
level by 20 dB.
Grasp the left side of the front panel and pull it out.
3
Press MUTE to activate the MUTE mode.
The audio level will decrease by about 20 dB.
Pressing MUTE again will bring the audio back to its
previous level.
•
•
The front panel may become hot in normal usage (especially the
connector terminals on the back of the front panel.) This is not a
malfunction.
To protect the front panel, place it in the supplied carrying case.
Changing the Display Type
There are three selectable display types (only one for the CDA-9830).
Attaching
You can also deactivate the display.
Insert the right side of the front panel into the main
unit. Align the groove on the front panel with the
projections on the main unit.
1
Press DISP/B.OUT to switch the display type.
For CDA-9831:
Push the left side of the front panel until it locks
firmly into the main unit.
2
Type1 → Type2 → Type3 → OFF → Type1
Type1 : The indicator on the left changes in a fixed sequence.
Type2 : The indicator on the left changes according to the
setting (see "Setting the Multicolor Illumination" on
page 22).
2
Type3 : The indicator on the left changes according to audio
level.
1
For CDA-9830:
VOLUME SETTING → LEVEL INDICATOR → OFF → VOLUME
•
•
Before attaching the front panel, make sure that there is no dirt or
dust on the connector terminals and no foreign object between the
front panel and the main unit.
Attach the front panel carefully. Hold the panel by its sides to avoid
pushing any buttons by mistake.
SETTING
Audio Level Display
7-EN
Download from Www.Somanuals.com. All Manuals Search And Download.
Press g or f to tune in the desired station.
Holding down g or f will change the frequency
continuously.
4
Radio
SOURCE/ TUNE/
POWER A.ME
•
The ST indicator appears on the display when a stereo FM station
is tuned in.
BAND/
TEL.
SEARCH
Manual Storing of Station Presets
Select the radio band and tune in a desired radio
station you wish to store in the preset memory.
1
Press and hold, for at least 2 seconds, any one of
the preset buttons (1 through 6) that you want
to store the station on .
2
Rotary
encoder
Preset buttons
(1 through 6)
g MENU f
The selected station is stored.
The display shows the band, preset no. and station
frequency memorized.
Changing the Radio Frequencies for each
Country
For customers not living in North America, change the radio
frequencies as follows.
•
•
A total of 18 stations can be stored in the preset memory (6 stations
for each band; FM1, FM2 and AM).
If you store a station in a preset memory which already has a
station, the current station will be cleared and replaced with the
new station.
Press MENU to select the SETUP mode.
1
Automatic Memory of Station Presets
Select the "AREA" mode by pressing g or f.
2
3
Press BAND/TEL. repeatedly until the desired
radio band is displayed.
1
Choose either AREA 1 or AREA 2 by turning the
Rotary encoder.
Press and hold TUNE/A.ME for at least 2 seconds.
2
The frequency on the display continues to change while
the automatic memory is in progress. The tuner will
automatically seek and store 6 strong stations in the
selected band. They will be stored into buttons 1 to 6 in
order of signal strength.
AREA 1: Radio frequencies for North America
AREA 2: Other Radio frequencies
Press MENU to select RETURN.
The unit returns to normal mode.
Pressing and holding MENU for at least 2 seconds will
return to normal mode.
4
When the automatic memory has been completed, the
tuner goes to the station stored in preset location no. 1.
•
The stored radio stations will be cleared every time you change the
setting.
•
If no stations are stored, the tuner will return to the original station
you were listening to before the auto memory procedure began.
Listening to Radio
Tuning to Preset Stations
Press SOURCE/POWER until a radio frequency
appears in the display.
1
Press BAND/TEL. repeatedly until the desired
band is displayed.
1
Press BAND/TEL. repeatedly until the desired
radio band is displayed.
2
Press any one of the station preset buttons (1
through 6) that has your desired radio station in
2
memory.
FM1 → FM2 → AM → FM1
The display shows the band, preset number and
frequency of the station selected.
Press TUNE/A.ME to select the tuning mode.
3
SEEK DX (Distance mode) → SEEK LO (Local mode) →
MANUAL (Manual mode) → SEEK DX
•
The initial mode is DX SEEK (Distance mode).
Distance mode:
Both strong and weak stations will be automatically tuned in
(Automatic Seek Tuning).
Local mode:
Only strong stations will be automatically tuned in (Automatic
Seek Tuning).
Manual mode:
The frequency is manually tuned in steps (Manual tuning).
8-EN
Download from Www.Somanuals.com. All Manuals Search And Download.
Station Title Search Function
If the title of a radio station is entered, you can search for that radio
CD / MP3 / WMA
station by its title while listening to the currently received radio
station.
.
SOURCE/
POWER
TITLE
SEARCH
-/J
8
Press SEARCH
Search mode.
in Radio mode to switch to Title
1
The first title input blinks in the display.
Select the desired title by turning the Rotary
encoder within 10 seconds.
2
3
Press the Rotary encoder to receive the
frequency of the selected title.
Rotary
encoder
f
9
g
F
4(
)
5(
)
6(
)
c
•
Search mode in Title Search mode is canceled by pressing and
holding SEARCH for at least 2 seconds.
•
If a station has no title, "NO TITLE" is displayed for 2 seconds.
Playback
Frequency Search Function
You can search for a radio station by its frequency.
Press c.
1
2
The movable display will open.
Insert a disc with the label side facing up.
Press and hold SEARCH
in Radio mode to activate Frequency Search mode.
for at least 2 seconds
1
2
The disc will be pulled into the unit automatically.
Turn the Rotary encoder within 10 seconds to
select the desired frequency.
Press the Rotary encoder to receive the selected
frequency.
3
The movable display will close and playback will begin.
When a disc is already inserted, press SOURCE/POWER
to switch to the CD mode.
•
Search mode in Frequency Search mode is canceled by pressing
and holding SEARCH for at least 2 seconds.
The mode will change every time the button is pressed.
TUNER → CD → CD CHANGER* → TUNER
* Only when the CD changer is connected
While playing back MP3/WMA, press 8 or 9 to
3
select the desired folder.
Pressing and holding 8 or 9 will change folders
continuously.
Press g or f to select the desired track (file).
4
Returning to the beginning of the current track (file):
Press g.
Fast backward :
Press and hold g.
Advancing to the beginning of the next track (file) :
Press f.
Fast forward :
Press and hold f.
To pause playback, press -/J.
Pressing -/J again will resume playback.
5
To eject the disc, press c.
6
•
Do not remove a CD during its eject cycle. Do not load more than
one disc at a time. A malfunction may result from doing either.
If the CD does not eject, press and hold c for at least 2 seconds
with the movable display open.
•
Continued
9-EN
Download from Www.Somanuals.com. All Manuals Search And Download.
•
•
The CD-player can play discs containing audio data, MP3 data
and WMA data.
A WMA format file that is protected by DRM (Digital Rights
Management) cannot be played back on this unit.
"MP3" is displayed during MP3 playback.
"WMA" is displayed during WMA playback.
The track display for MP3/WMA data playback is the file numbers
recorded on the disc.
Playing back a Playlist
You can play playlists you have prepared in advance on the computer.
Both MP3 and WMA playlists can be played.
Playlists that can be played back by this device have the file extension
"m3u"/"asx."
•
•
•
•
If the HDA-5460 model is connected to the unit, some operations
(for example changing the source, selecting the file by holding
buttons up or down, etc.), can be carried out on this unit.
Press 8 or 9 to select a playlist.
By pressing and holding 8 or 9, the playlists move up or
down continuously.
•
•
•
If there is a playlist and folder on the disc, the playlist starts to
play back prior to the folder.
Up to 5 playlist can be played back. Playlists from the 6th onwards
cannot be played back.
Refer to the software instruction manual on how to create a
playlist.
MP3/WMA Play Display
CDA-9831
The folder number, file number, sampling rate, and bit rate
will be displayed as described below.
File number
display
Playlist Display
While playing back a playlist, the folder and file numbers that are
stored in the playlist are displayed.
44.1kHz
01 03
CDA-9831
Sampling rate
display
Folder number
display
P-LIST
03 05
The sampling rate and the bit
rate (frame display) are
alternately displayed.*
CDA-9830
File number
display
P-L
F03 T05
kbps
160
01 03
Bit rate
display
Folder number
display
*When the unit is connected to the Amplifier Link, the
temperature is automatically indicated.
Sampling rate → Bit rate → Temperature → Sampling rate
CDA-9830
The folder number and file number will be displayed as
described below.
F01 T03
Folder number
display
File number
display
•
Press TITLE
to switch the display. Please see “Displaying the
Title/Text” (page 19) for information about display switching.
10-EN
Download from Www.Somanuals.com. All Manuals Search And Download.
Repeat Play
M.I.X. (Random Play)
Press 4 (
played.
) to play back repeatedly the track being
Press 5 (
) in the play or pause mode.
The tracks (files) on the disc will be played back in random
The track (file) will be played repeatedly.
sequence.
Press 4 (
) again and select OFF to deactivate repeat play.
To cancel M.I.X. play, press 5 (
) again.
CD mode :
CD mode :
↓
RPT
↓
RPT
↓
(off)
: Only a track is repeatedly played back
*1
: A disc is repeatedly played back
M.I.X.: Track are played back in
random sequence.
↓
*3
M.I.X.: The tracks on all the CDs in the current
magazine will be included in the random
playback sequence.
↓
(off)
*1 When a CD changer is connected
•
If REPEAT is set to ON during M.I.X. play in CD changer mode,
M.I.X. will apply to the current disc only.
*3 When a CD changer equipped with the All M.I.X. function is
connected
MP3/WMA mode :
•
If M.I.X. is set to ON during RPT
(REPEAT ALL) play in CD
changer mode, M.I.X. will apply to the current disc only.
RPT
↓
RPT
: Only a file is repeatedly played back
MP3/WMA mode :
:
Only files in a folder or playlist are repeatedly
played back
↓
↓
RPT
↓
(off)
*2
M.I.X.: Only files in a folder are played back in
random sequence.
↓
: A disc is repeatedly played back
M.I.X.: Files are played back in random sequence.
If an MP3 compatible CD changer is
connected, all files in a disc are played back
in random sequence, and playback shifts to
the next disc.
*2 When an MP3 compatible CD changer is connected
•
If a 6-disc CD changer or an MP3 compatible CD changer is
connected:
In CD changer mode, press F to illuminate the "FUNC" indicator,
and go to the step above within 5 seconds.
↓
(off)
•
If a 12-disc CD changer is connected:
In CD changer mode, press F twice to illuminate the "FUNC"
indicator, and go to the step above within 5 seconds.
•
If a 6-disc CD changer or an MP3 compatible CD changer is
connected:
In CD changer mode, press F to illuminate the "FUNC" indicator,
and go to the step above within 5 seconds.
•
•
If a 12-disc CD changer is connected:
In CD changer mode, press F twice to illuminate the "FUNC"
indicator, and go to the step above within 5 seconds.
When playing back a playlist, M.I.X. cannot be played.
11-EN
Download from Www.Somanuals.com. All Manuals Search And Download.
Folder Name Search mode
Scanning Programs
Turn the Rotary encoder within 10 seconds to
2
Press 6 (
) to activate the Scan mode.
select the desired folder or playlist.
The first 10 seconds of each track (file) will be played back in
succession.
Press the Rotary encoder to play back the first
file in the selected folder or playlist.
3
To stop scanning, press 6 (
) and deactivate the Scan
mode.
•
•
•
Search mode is canceled by pressing and holding SEARCH
at least 2 seconds in Folder Name Search mode.
for
•
If a 6-disc CD changer or an MP3 compatible CD changer is
While in Folder Name Search mode, press SEARCH to switch to
File Name Search mode.
"NO FILE" is displayed for 2 seconds if the folder or playlist that
is selected by the Folder Name Search mode contains no files.
"0 (zero)" is displayed for the root folder.
connected:
In CD changer mode, press F to illuminate the "FUNC" indicator,
and go to the step above within 5 seconds.
If a 12-disc CD changer is connected:
•
•
•
In CD changer mode, press F twice to illuminate the "FUNC"
indicator, and go to the step above within 5 seconds.
Folder Name Search cannot be made during M.I.X. play.
Quick Search
You can search for tracks(files).
Searching from CD Text
Tracks can be searched and played using the CD text on the disk. In
the case of discs and changers that do not support text, searches can
be made using the track numbers.
1
Press and hold SEARCH
in the CD/Changer/MP3/WMA mode to activate
for at least 2 seconds
Quick Search mode.
Press SEARCH
This will set the search mode.
during play.
1
2
Turn the Rotary encoder within 10 seconds to
select a desired track(file).
The selected track is played back immediately.
2
Turn the Rotary encoder to select the desired
track, then press the Rotary encoder.
This will play the selected track.
•
Search mode is canceled by pressing and holding SEARCH for
at least 2 seconds in Quick Search mode.
•
•
Press and hold SEARCH for at least 2 seconds in the search
mode to cancel. Or, the search mode will be canceled when an
operation has not been performed in 10 seconds.
About MP3/WMA
CD text search cannot be made during M.I.X. play.
CAUTION
Except for private use, duplicating audio data (including MP3/
WMA data) or distributing, transferring, or copying it, whether
for free or for a fee, without permission of the copyright holder is
strictly prohibited by the Copyright Act and by international
treaty.
File/Folder Name Search
(concerning MP3/WMA)
You can display and search for the folder and file name while
listening to the file currently being played back.
What is MP3?
Press SEARCH
mode or Folder Name Search mode in MP3/WMA
mode.
to select File Name Search
1
MP3, whose official name is “MPEG-1 Audio Layer 3,” is a
compression standard prescribed by the ISO, the International
Standardization Organization and MPEG which is a joint
activity institution of the IEC.
File Name Search mode
MP3 files contain compressed audio data. MP3 encoding is
capable of compressing audio data at extremely high ratios,
reducing the size of music files to as much as one-tenth their
original size. This is achieved while still maintaining near CD
quality. The MP3 format realizes such high compression ratios
by eliminating the sounds that are either inaudible to the
human ear or masked by other sounds.
Press 8 or 9 to select another Folder or Playlist.
2
Select the desired file by turning the Rotary
encoder within 10 seconds.
3
Press the Rotary encoder to play back the
selected file.
4
What is WMA?
WMA, or “Windows Media™ Audio,” is compressed audio
data.
WMA allows you to create music files and store them at higher
ratios of compression than MP3 audio data (approx. half
original size). This is achieved while still maintaining CD
quality sound.
•
•
File Name Search mode is canceled by pressing and holding
SEARCH
for at least 2 seconds.
While in File Name Search mode, press SEARCH to switch to
Folder Name Search mode.
File Name Search cannot be made during M.I.X. play.
File Name Search cannot be made while playing back a playlist.
•
•
12-EN
Download from Www.Somanuals.com. All Manuals Search And Download.
Method for creating MP3/WMA files
Order of tracks
The unit plays the files in the order that the writing software
Audio data is compressed by using MP3/WMA specified
software. For details on creating MP3/WMA files, refer to the
user's manual for that software.
MP3/WMA files that can be played back by this device have
the file extension “mp3” / “wma”. Files with no extension
cannot be played back. (WMA ver. 7.1 and 8 are supported)
writes them. Therefore, the playing order may not be the same
as the order you input. The playback order of the folders and
files is as follows. However, the folder and file playback order
differs from the folder no. and file no. indicated on the display.
Supported playback sampling rates and bit rates
0
1
MP3
Sampling rates: 48 kHz, 44.1 kHz, 32 kHz, 24 kHz, 22.05 kHz,
16 kHz, 12 kHz, 11.025 kHz, 8 kHz
2
Root folder
Bit rates:
8 - 320 kbps
2
WMA
Sampling rates: 48 kHz, 44.1 kHz, 32 kHz, 24 kHz,
22.05 kHz
3
3
Bit rates:
48 - 192 kbps
4
Note that for sampling rates, this device’s frame display (Page
19) may not display correctly.
This device may not play back correctly depending on
sampling rates.
4
5
6
ID3 tags/WMA tags
5
This device supports ID3 tag v1 and v2, and WMA tag.
If tag data is in an MP3/WMA file, this device can display the
title (track title), artist name, and album name ID3 tag/WMA
tag data.
7
1
This device can only display single-byte alphanumeric
characters (up to 30 for ID3 tags and up to 15 for WMA tags)
and the underscore. For non-supported characters, “NO
SUPPORT” ("NO SUPRT" for CDA-9830) is displayed.
The tag information may not be correctly displayed,
depending on the contents.
Folder
MP3/WMA File
Producing MP3/WMA discs
MP3/WMA files are prepared, then written to a CD-R or CD-
RW using CD-R writing software. A disc can hold up to 256
folders and 999 files (including Root Folders).
Terminology
Bit rate
Media supported
This is the “sound” compression rate specified for encoding. The
higher the bit rate, the higher the sound quality, but also the larger
the files.
The media that this device can play back are CD-ROMs, CD-
Rs, and CD-RWs.
Sampling rate
Corresponding File Systems
This value shows how many times per second the data is sampled
(recorded). For example, music CDs use a sampling rate of 44.1
kHz, so the sound is sampled (recorded) 44,100 times per second.
The higher the sampling rate, the higher the sound quality, but also
the larger the volume of data.
This device supports discs formatted with ISO9660 Level 1 or
Level 2.
Under the ISO9660 standard, there are some restrictions to
remember.
The maximum nested folder depth is 8 (including the root
directory). File/folder names are limited to 30 characters
(including the extension).
Valid characters for folder/file names are letters A-Z (all
caps), numbers 0-9, and ‘_’ (underscore).
Encoding
Converting music CDs, WAVE (AIFF) files, and other sound files
into the specified audio compression format.
Tag
Song information such as track titles, artist names, album names,
etc., written into MP3/WMA files.
MP3: ID3 tag
This device also can play back discs in Joliet, Romeo, etc.,
and other standards that conform to ISO9660. However,
sometimes the file names, folder names, etc., are not
displayed correctly.
WMA: WMA tag
Root folder
Formats supported
The root folder is found at the top of the file system. The root folder
contains all folders and files.
This device supports CD-ROM XA, Mixed Mode CD,
Enhanced CD (CD-Extra) and Multi-Session.
This device cannot correctly play back discs recorded with
Track At Once or packet writing.
13-EN
Download from Www.Somanuals.com. All Manuals Search And Download.
Turn the Rotary encoder to select the desired
setting.
4
Sound Setting
HPF (Setting the High Pass Filter):
FLAT (OFF) ↔ 80Hz ↔ 120Hz ↔160Hz
SOURCE/
POWER
BAND/
TEL.
All frequencies above the selected cutoff are output.
Rotary encoder
LPF (Setting the Low Pass Filter):
FLAT (OFF) ↔ 80Hz ↔ 120Hz ↔160Hz
All frequencies below the selected cutoff are output.
(Only available when using the subwoofer output from this
unit.)
To store the adjusted contents
1) Press and hold, for at least 2 seconds, the preset
buttons (1 or 2) into which you wish to store the adjusted
contents.
f
Preset button (1 or 2)
g MENU MX
Press the Rotary encoder to confirm the
adjusted contents.
5
Adjusting Balance (Between Left and Right)/
Fader (Between Front and Rear)/Defeat
The adjusted contents are not stored if the Rotary encoder
is not pressed.
After setting, press MENU to select RETURN.
The unit returns to normal mode.
Pressing and holding MENU for at least 2 seconds will
return to normal mode.
6
Press Rotary encoder repeatedly to choose the
desired mode.
1
Each press changes the modes as follows:
SUBWOOFER*1 → BALANCE → FADER → DEFEAT →
VOLUME → SUBWOOFER*1
•
•
•
•
The setting mode returns to normal mode if no buttons are pressed
within 15 seconds.
These functions are inoperative when an external, Ai-NET
processor is connected.
Except when the HPF and LPF is turned OFF, the subwoofer is in
monaural mode.
When the subwoofer is set to OFF, LPF mode and change of phase
does not work.
Subwoofer : 0 ~ +15
Balance : L15 ~ R15
Fader : R15 ~ F15
Defeat : ON/OFF
Volume : 0 ~ 35
Press g or f after selecting the Subwoofer mode,
and the subwoofer output phase is toggled NORMAL
(PHASE 0°) or REVERS (PHASE 180°).
Recalling the Stored built-in Crossover
Settings
•
If the Rotary encoder is not pressed within 5 seconds after
selecting the BALANCE, FADER, DEFEAT or SUBWOOFER
mode, the unit automatically returns to normal mode.
Press and hold MENU for at least 2 seconds.
1
*1 When the subwoofer mode is set to OFF, its level and phase cannot
be adjusted.
Press MENU to select HPF/LPF.
2
Turn the Rotary encoder until the desired sound
is obtained in each mode.
By setting Defeat ON, previously adjusted settings of EQ
2
Press the preset button (1 or 2) to which your
desired built-in crossover settings are assigned.
3
will return to the factory defaults and MX is turned off.
Press MENU to select RETURN.
The unit returns to normal mode.
Pressing and holding MENU for at least 2 seconds will
return to normal mode.
4
•
Depending on the connected devices, some functions and display
indications do not work.
•
The setting mode returns to normal mode if no buttons are pressed
within 15 seconds.
Adjusting and Storing the built-in Crossover
The High and Low Pass Filters on this unit can be adjusted to suit
your personal taste.
Press and hold MENU for at least 2 seconds.
1
Press MENU to select HPF/LPF.
2
Press BAND/TEL. to change the setting mode.
3
HPF ↔ LPF*
* When the subwoofer output of this unit is turned off, LPF and
phase are deactivated.
14-EN
Download from Www.Somanuals.com. All Manuals Search And Download.
Press SOURCE/POWER to select your desired
band width (Q).
6
Equalizer Presets
10 typical equalizer settings are preset at the factory for a variety of
musical source material.
Adjustable band width:
BAND1 : 1.0, 2.0, 3.0,
BAND2 : 1.0, 1.5, 2.0
BAND3 : 1.0, 2.0, 3.0
BAND4 : 1.0 (fixed band width)
Press MENU to select Factory's EQ (P-EQ for
CDA-9830).
1
To store the adjusted curve
1) Press and hold, for at least 2 seconds, the preset
buttons (1 or 2) into which you wish to store the adjusted
curve.
Press either g or f.
With each press of the button, the equalizer mode will
display the selected equalizer characteristic.
2
To set another channel, repeat steps 3 to 6.
7
8
FLAT(OFF) ↔ ROCK ↔ POPS ↔ JAZZ & BLUES (JAZZ) ↔
ELECTRICAL (ELECTRIC) ↔ HIPHOP & RAP (HIPHOP) ↔
EASY LISTEN (EASY) ↔ COUNTRY ↔ CLASSICAL (CLASSIC)
↔ NEWS ↔ USER'S EQ 1,2 (USERS 1,2) ↔ FLAT(OFF)
Press the Rotary encoder to confirm the
adjusted contents.
The adjusted contents are not stored if the Rotary encoder
is not pressed.
Press MENU to select RETURN.
The unit returns to normal mode.
3
Pressing and holding MENU for at least 2 seconds will
return to normal mode.
After setting, press MENU to select RETURN.
The unit returns to normal mode.
9
Pressing and holding MENU for at least 2 seconds will
return to normal mode.
•
•
This function is inoperable when DEFEAT is set to ON (page 14).
EQ mode is automatically canceled if no buttons are pressed
within 15 seconds.
By selecting USER'S EQ 1 or EQ 2 (USERS 1 or USERS 2 for
CDA-9830), you can recall the stored preset number in "Adjusting
and Storing the Equalizer Curve."
•
•
EQ mode is automatically canceled if no buttons are pressed
within 15 seconds.
This function is inoperable when DEFEAT is set to ON (page 14).
•
Recalling the Stored Equalizer Curve
Adjusting and Storing the Equalizer Curve
You can modify the Equalizer settings to create a response curve more
Press and hold MENU for at least 2 seconds.
1
appealing to your personal taste.
Press MENU to select USER'S EQ (USERS for
CDA-9830).
2
Press and hold MENU for at least 2 seconds.
1
Press either preset button (1 or 2) to activate
your desired curve.
3
Press MENU to select USER'S EQ (USERS for
CDA-9830).
2
Press MENU to select RETURN.
The unit returns to normal mode.
Pressing and holding MENU for at least 2 seconds will
return to normal mode.
4
Press BAND/TEL. to select your desired
frequency band.
3
BAND1 → BAND2 → BAND3 → BAND4 → BAND1
•
EQ mode is automatically canceled if no operation is performed
within 15 seconds.
This function is inoperable when DEFEAT is set to ON (page 14).
You can recall the adjusted equalizer curve from "Equalizer Presets"
(this page).
Press g or f to select your desired
frequency.
Adjustable frequency bands:
BAND1 : 40Hz, 60Hz, 90Hz
BAND2 : 100Hz, 150Hz, 200Hz
BAND3 : 500Hz, 700Hz, 1kHz, 2kHz, 4kHz, 6kHz
BAND4 : 10kHz, 12.5kHz, 15kHz
4
•
•
Turn the Rotary encoder to adjust the level.
5
15-EN
Download from Www.Somanuals.com. All Manuals Search And Download.
Example 2. Listening Position: All Seats
About Time Correction
Adjust the time correction level of each speaker to almost the same
level.
The distance between the listener and the speakers in a car vary
widely due to the complex speaker placement. This difference in the
distances from the speakers to the listener creates a shift in the sounds
image and frequency characteristics. This is caused by the time delay
between the sound reaching the listener’s right versus the left ear.
To correct this, the CDA-9831/CDA-9830 is able to delay the audio
signal to the speakers closest to the listener. This effectively creates a
perception of increased distance for those speakers. The listener can
be placed at an equal distance between the left and right speakers for
optimum staging.
Sit in the listening position (driver’s seat, etc.) and
measure the distance (in meters) between your
head and the various speakers.
1
Calculate the difference between the distance to
2
the farthest speaker and the other speakers.
L = (distance to farthest speaker) – (distance to other
speakers)
The adjustment will be made for each speaker in 0.1 ms steps.
Divide the distances calculated for the speakers by
3
Example 1. Listening Position: Front Left Seat
the speed of sound (343 m/s (765 mph) at 20˚C).
These values are the time correction values for the
different speakers.
Adjust the time correction level of the front left speaker
to a high value and the rear right to zero or a low value.
Bass Focus
The time difference between the front-rear/left-right speakers, can be
adjusted at the same time. With an initial delay of 0.1 ms for each of
the 0 to 99 steps, audible time correction can be done.
Press and hold MENU for at least 2 seconds.
1
5.1ms
Press MENU to select T.CORR (T-CORR for
CDA-9830).
2
0.5m
2.25m
Press g or f to select the Bass Focus mode.
3
1
1
Bass Focus mode ↔ Time Correction mode
*
*
Press BAND/TEL. to select the speakers to be
adjusted (see below).
4
*1 Subwoofer speaker.
You cannot change the Time Correction value for the subwoofer,
but you can set the subwoofer's apparent position to the front by
adjusting the Time Correction value of the front and rear speakers.
For details, refer to the “ *1 ” on page 17.
FL
RL
FR
RR
FL
RL
FR
RR
→
→
The sound is not balanced because the distance between the
listening position and the various speakers is different.
The difference in distance between the front left speaker and
the rear right speaker is 1.75 m (68-7/8").
Front (left-right)
speakers
Left (front-rear)
speakers
FL
RL
FR
RR
FL
RL
FR
RR
←
←
Here we calculate the time correction value for the front left
speaker in the diagram on the above.
Conditions:
Farthest Speaker – listening position : 2.25 m (88-9/16")
Front left speaker – listening position : 0.5 m (19-11/16")
Calculation: L = 2.25 m – 0.5 m = 1.75 m (68-7/8")
Time correction = 1.75 ÷ 343*2 × 1000 = 5.1 (ms)
Rear (left-right)
speakers
Right (front-rear)
speakers
*2 Speed of sound: 343 m/s (765 mph) at 20˚C
Turn the Rotary encoder to adjust the delay (see
Time Difference Table).
5
6
7
In other words, giving the front left speaker a time correction
value of 5.1 ms makes it seem as if its distance from the
listener is the same as the distance to the farthest speaker.
To set another channel (speakers), repeat steps 4
and 5.
Time correction eliminates the differences in the time required
for the sound to reach the listening position.
The time of the front left speaker is corrected by 5.1 ms so that
its sound reaches the listening position at the same time as the
sound of other speakers.
Press the Rotary encoder to confirm the
adjusted contents.
The adjusted contents are not stored if the Rotary encoder
is not pressed.
16-EN
Download from Www.Somanuals.com. All Manuals Search And Download.
Time Difference Table
After setting, press MENU to select RETURN.
The unit returns to normal mode.
Pressing and holding MENU for at least 2 seconds will
return to normal mode.
8
Time
Difference
Time
Difference
(ms)
Delay
Distance
cm (inch)
Delay
Number
Distance
cm (inch)
Number
(ms)
0
0.0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1.0
1.1
1.2
1.3
1.4
1.5
1.6
1.7
1.8
1.9
2.0
2.1
2.2
2.3
2.4
2.5
2.6
2.7
2.8
2.9
3.0
3.1
3.2
3.3
3.4
3.5
3.6
3.7
3.8
3.9
4.0
4.1
4.2
4.3
4.4
4.5
4.6
4.7
4.8
4.9
5.0
0.0
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
5.1
5.2
5.3
5.4
5.5
5.6
5.7
5.8
5.9
6.0
6.1
6.2
6.3
6.4
6.5
6.6
6.7
6.8
6.9
7.0
7.1
7.2
7.3
7.4
7.5
7.6
7.7
7.8
7.9
8.0
8.1
8.2
8.3
8.4
8.5
8.6
8.7
8.8
8.9
9.0
9.1
9.2
9.3
9.4
9.5
9.6
9.7
9.8
9.9
174.9 (68-7/8")
178.4 (70-1/4")
181.8 (71-9/16")
185.2 (72-7/8")
188.7 (74-1/4")
192.1 (75-5/8")
195.5 (77")
•
•
Any manual time correction adjustments will also affect
corrections made in Bass Focus.
Bass Focus mode is automatically canceled if no operation is
performed within 15 seconds.
1
3.4 (1-3/8")
2
6.9 (2-3/4")
3
10.3 (4-1/16")
13.7 (5-3/8")
4
Example setting for steps 4 and 5
5
17.2 (6-13/16")
20.6 (8-1/8")
6
(1) Press BAND/TEL. to select the front (left and
right) speakers.Then turn the Rotary encoder to
select 1.5 ms (Delay no. 15 in the table).The time
difference is 1.5 ms for both front (left and right
speakers.
7
24.0 (9-7/16")
27.4 (10-13/16")
30.9 (12-3/16")
34.3 (13-1/2")
37.7 (14-13/16")
41.2 (16-1/4")
44.6 (17-9/16")
48.0 (18-7/8")
51.5 (20-1/4")
54.9 (21-5/8")
58.3 (22-15/16")
61.7 (24-1/4")
65.2 (25-5/8")
68.6 (27")
198.9 (78-5/16")
202.4 (79-11/16")
205.8 (81")
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
209.2 (82-3/8")
212.7 (83-3/4")
216.1 (85-1/16")
219.5 (86-3/8")
223.0 (87-3/4")
226.4 (89-1/8")
229.8 (90-1/2")
233.2 (91-13/16")
236.7 (93-3/16")
240.1 (94-1/2")
243.5 (95-7/8")
247.0 (97-1/4")
250.4 (98-9/16")
253.8 (99-7/8")
257.3 (101-1/4")
260.7 (102-5/8")
264.1 (104")
1.5ms
1.5ms
1
*
72.0 (28-3/8")
75.5 (29-11/16")
78.9 (31-1/16")
82.3 (32-3/8")
85.8 (33-3/4")
89.2 (35-1/8")
92.6 (36-7/16")
96.0 (37-3/4")
99.5 (39-13/16")
102.9 (40-1/2")
106.3 (41-7/8")
109.8 (43-1/4")
113.2 (44-9/16")
116.6 (45-7/8")
120.1 (47-5/16")
123.5 (48-5/8")
126.9 (49-15/16")
130.3 (51-5/16")
133.8 (52-11/16")
137.2 (54")
(2) Press BAND/TEL. to select the left (front and rear)
speakers.Then turn the Rotary encoder to select
1.5 ms (Delay no. 15 in the table).The time
267.5 (105-5/16")
271.0 (106-11/16")
274.4 (108-1/16")
277.8 (109-3/8")
281.3 (110-3/4")
284.7 (112-1/16")
288.1 (113-1/16")
291.6 (114-3/4")
295.0 (116-1/8")
298.4 (117-1/2")
301.8 (118-13/16")
305.3 (120-3/16")
308.7 (121-1/2")
312.1 (122-7/8")
315.6 (124-1/4")
319.0 (125-9/16")
322.4 (126-7/8")
325.9 (128-5/16")
329.3 (129-5/8")
332.7 (131")
difference is 3.0 ms*2 for the front left speaker, and
1.5ms for the left rear speaker, creating the
impression of an equal listening between the front
left speaker and the other speakers.
3.0ms
1.5ms
1.5ms
1.5ms
140.6 (55-3/8")
144.1 (56-3/4")
147.5 (58-1/16")
150.9 (59-3/8")
154.4 (60-3/4")
157.8 (62-1/8")
161.2 (63-7/16")
164.6 (64-3/4")
168.1 (66-3/16")
171.5 (67-1/2")
1.5ms
1
*
336.1 (132-5/16")
339.6 (133-11/16")
*1 Subwoofer speaker.
Delay (turn the rotary encoder) the audio signal to the front (left
and right) speakers to make the apparent position of the subwoofer
to be at the front. In doing this, the apparent position between the
front (left and right) speakers and subwoofer will appear equal to
the driver. After performing the above, you can change the
positions of the left and right speakers by delaying the time .
*2 Because the time difference was already set to 1.5 ms for the front
left speaker to begin with, the additional correction of 1.5 ms
makes the total time difference of the front left speaker 3.0 ms.
17-EN
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting and Storing the Time Correction
Setting the MX Mode
Before performing the following procedures, refer to "About Time
Correction" (page 16).
MX (Media Xpander) makes vocals or instruments sound distinct
regardless of the music source. The FM radio, CD, and MP3, will be
able to reproduce the music clearly even in cars with a lot of road
noise.
Press and hold MENU for at least 2 seconds.
1
Press MENU to select T.CORR (T-CORR for
CDA-9830).
Press MX to select MX ON.
2
1
Press SOURCE/POWER to select the source to
which you want to apply MX (Media Xpander).
2
Press g or f to make time corrections.
3
Each press changes the mode as follows:
Press and hold MX for at least 2 seconds to
activate the level setting mode.
3
Bass Focus mode ↔ Time Correction mode
Press BAND/TEL. to select a speaker to be
adjusted.
4
Turn the Rotary encoder to select your preferred
level or OFF.
4
CDA-9831
FM (MX level 1 to 3):
Front – L → Front – R → Rear – L → Rear – R → Front – L
The medium to high frequencies become clearer, and
produces well balanced sound at all frequencies.
CDA-9830
F – L → F – R → R – L → R – R → F – L
CD/WAV (MX level 1 to 3):
CD mode processes a large amount of data during playback.
MX takes advantage of this large data quantity to reproduce a
more clear, clean output.
Turn the Rotary encoder to adjust the desired
time correction value.
5
To store the adjusted contents
MP3/WMA/XM (MX level 1 to 3):
1) Press and hold, for at least 2 seconds, the preset
buttons (1 or 2) into which you wish to store the adjusted
contents.
This corrects information that was lost at the time of
compression. This reproduces a well-balanced sound close to
the original.
DVD (Video CD)
(MOVIE MX level 1 to 2):
Repeat step 4 and 5 to set another speaker.
6
The dialog portion of a video is reproduced more clearly.
Press the Rotary encoder to confirm the
adjusted contents.
The adjusted contents are not stored if the Rotary encoder
is not pressed.
7
(MUSIC MX level 1):
A DVD or Video CD contains a large quantity of data such as
music clip. MX uses this data to reproduce the sound
accurately.
AUX (MX level 1):
After setting, press MENU to select RETURN.
The unit returns to normal mode.
Pressing and holding MENU for at least 2 seconds will
return to normal mode.
8
Choose the MX mode (MP3, MUSIC, or MOVIE) that
corresponds to the media connected.
If two external devices are connected, a different MX
mode for each media can be selected.
•
If no operation is performed in 15 seconds, the unit returns to
normal mode.
Press Rotary encoder to return to normal mode.
5
•
•
To cancel MX mode for all music sources, press MX to turn MX off.
MX mode is automatically canceled if no buttons are pressed
within 15 seconds.
Recalling the Stored Time Correction Settings
•
•
Each music source, such as FM radio, CD, and MP3 can have its
own MX setting.
Press and hold MENU for at least 2 seconds.
1
On disks with both MP3/WMA and CD-DA, when the source
changes from “MP3/WMA to CD-DA” or “CD-DA to MP3/WMA,”
MX-mode switching may delay playback slightly.
Setting to MX OFF sets MX mode of each music source to OFF.
This function is inoperable when DEFEAT is set to ON.
There is no MX mode for AM radio.
If an audio processor with the MX function (PXA-H700, etc.) is
connected, its own MX processing is applied to the music source.
Since the processor MX settings may not match the head unit, the
audio processor needs to be adjusted. For details, refer to the
Owner’s Manual of the audio processor.
Press MENU to select T.CORR (T-CORR for
CDA-9830).
2
•
•
•
•
Press g or f to make time corrections.
3
Each press changes the mode as follows:
Bass Focus mode ↔ Time Correction mode
Press the preset button (1 or 2) to which your
desired time correction is assigned.
4
Press MENU to select RETURN.
The unit returns to normal mode.
5
Pressing and holding MENU for at least 2 seconds will
return to normal mode.
•
Time Correction mode is automatically canceled if no operation is
performed within 15 seconds.
18-EN
Download from Www.Somanuals.com. All Manuals Search And Download.
About the indicator display
When displaying Title/Text, the following indicators are lit
according to the mode.
Other Functions
DISP/
SOURCE/
POWER
BAND/
TEL.
CDA-9831
-/J
TITLE
B.OUT
These indicators are
constantly lit.
1
2
3
4
5
6
g MENU
f
Rotary
encoder (1 through 6)
Preset buttons
When selection is
available by turning
the Rotary encoder,
an indicator is lit in
the display.
This indicator shows the strength
of the telephone signal.
When selection is available by
pressing g or f, the triangle
indicators are lit in the display.
Displaying the Title/Text
It is possible to display the CD/Station title if the title has been
previously inputted (“Titling Discs/Stations” page 20). Text
information, such as the disc name and the track name, will be
displayed if playing a CD text compatible disc. It is also possible to
display the folder name, the file name, and the tag, etc., while playing
MP3/WMA files.
CDA-9830
1 2 3 4 5 6
Press TITLE
.
The display will change every time the button is pressed.
These indicators are constantly lit.
The display in Radio mode:
FREQUENCY → CLOCK → TITLE → EXTERNAL AMPLIFIER
INFORMATION*5 → FREQUENCY
Indicator/
Mode
XM RADIO
Mode
MP3/WMA
Mode
TUNER
Mode
CD Mode
The display in CD mode:
Title being
displayed
1
—
—
—
TRACK NO./ELAPSED TIME → TRACK NO./CLOCK → TEXT
(DISC NAME)*1 → TEXT (TRACK NAME)*2 → TITLE →
EXTERNAL AMPLIFIER INFORMATION*5 → TRACK NO./
ELAPSED TIME
Folder Name
being
—
—
—
2
—
—
displayed
File Name
being
displayed
3
4
5
—
—
—
—
The display in MP3/WMA mode:
Artist Name*
being
displayed
Artist Name
being
displayed
FILE NO./ELAPSED TIME → FOLDER NO./FILE NO. → FILE
NO./CLOCK → FOLDER NAME*4 → FILE NAME → TRACK
NAME*2 → ARTIST NAME*2 → ALBUM NAME*2 → FRAME*3
→ EXTERNAL AMPLIFIER INFORMATION*5 → FILE NO./
ELAPSED TIME
Text (Disc
Name) being
displayed
Album Name*
being
displayed
—
Text (Track
Track Name*
Music Title/
Channel
Name being
displayed
*1 Displayed during playback of a disc with CD Text.
“NO TEXT” will be displayed when the CD contains no Text data.
*2 ID3 tag/WMA tag
Title being
displayed
Name) being being
6
displayed
displayed
If an MP3/WMA file contains ID3 tag/WMA tag information, the
ID3 tag/WMA tag information is displayed (e.g., track name, artist
name, and album name). All other tag data is ignored.
“NO DATA” will be displayed when an MP3/WMA file contains no
ID3 tag/WMA tag information.
*
Tag information
*3 CDA-9830 only:
The recording sampling rate and bit rate of the MP3/WMA file are
displayed.
*4 "0 (zero)" is displayed for the folder name of the root folder.
*5 Only when CDA-9831 is connected to an external Amplifier Link
compatible amplifier. For details, refer to "Displaying the External
Amplifier Information" (page 21).
Continued
19-EN
Download from Www.Somanuals.com. All Manuals Search And Download.
About “Title” and “Text”
Erasing Disc Title/Station Title
Title:
With this device, it is possible to input the CD/Station name
(this page). This inputted name is referred to as a “title.”
You cannot input or display titles on MP3/WMA discs.
Press TITLE
press again and hold for at least 2 seconds.
to select the Title Display.Then,
1
Text:
Press and hold -/J for at least 2 seconds.
The title in the display will blink.
2
3
Text compatible CDs contain text information such as the disc
name and track name. Such text information is referred to as “text.”
Press g or f repeatedly until the title you
want to erase is displayed.
•
•
•
Some characters may not be displayed correctly with this device,
depending on the character type.
The CD changer must also be CD Text compatible for the Text
information to be displayed.
When the Scroll Setting (page 24) is set to “SCROLL MANUAL,”
Press and hold -/J for at least 2 seconds to erase
the title displayed.
4
press and hold TITLE
for at least 3 seconds to scroll the Text
information only once (TEXT DISPLAY, FOLDER NAME
DISPLAY, FILE NAME DISPLAY or TAG DISPLAY mode).
“NO SUPPORT” (“NO SUPRT” for CDA-9830) is displayed
when the desired text information cannot be displayed on this unit.
If the title was not previously input, “NO TITLE” is displayed.
The text or tag information may not be correctly displayed,
depending on the contents.
Press TITLE
to cancel the title erasing mode.
5
•
•
You cannot erase CD-TEXT.
"NO DATA" is displayed for 2 seconds if the title is not input in
step 2, or if all titles are erased in step 4.
•
•
•
Displaying Time
Press TITLE
repeatedly until the time is displayed.
Titling Discs/Stations
It is possible to title your favorite CD's or radio stations.
Each press changes the display.
For details, see “Displaying the Title/Text” (page 19).
You cannot input titles on MP3/WMA discs.
•
•
Selecting any tuner or CD function while in the clock priority mode
will interrupt the time display momentarily. The function selected
will be displayed for about 5 seconds before the time returns to the
display.
When the power is off but the ignition key is on, press TITLE to
display the time.
Press TITLE
For details, see “Displaying the Title/Text” (page 19).
and select the Title Display.
1
2
3
4
Press and hold TITLE
The first character will blink.
for at least 2 seconds.
Turn the Rotary encoder to select the desired
letter/numeral/symbol available for naming.
Blackout Mode On and Off
When Blackout mode is turned on, the display will turn off to reduce
power consumption. This additional power enhances the sound quality.
Press Rotary encoder to store the first character.
The first character will stop blinking and the display will
automatically advance to the next character. When that
character begins to blink, you may choose the next letter
or symbol of your title.
Press and hold DISP/B.OUT for at least 2 seconds to
activate the blackout mode.
The display will turn off.
•
If any button on the unit is pressed during the blackout mode, the
function will be displayed for 5 seconds to show the operation
before returning to Blackout mode.
Repeat steps 3 and 4 above to complete the titling.
Pressing the Rotary encoder after entering the 8th
character automatically stores the title into memory.
5
To cancel Blackout mode, press and hold DISP/B.OUT for at
When entering a title of less than 8 characters (for
example, 3 character title):
least 2 seconds.
After entering 3 characters, the 4th character space will
be blinking. Go to step 6 to complete the title.
Press TITLE
to record the title.
6
•
If you cancel while entering a title, selected characters are not
written.
•
You can enter 24 radio station titles and 18 CD titles on this unit. If
you try to store beyond the limit, the display will show “FULL
DATA.” At this point, no more titles can be stored. To input a new
title, one of the previously inputted titles must first be deleted.
The CD Changer title length or memory capacity varies depending
upon the model being used.
When you want to erase a title, enter the “ ” (“ ” for CDA-
9830) symbol into all spaces.
The operations described in steps 3 to 5 must be made within 10
seconds. The input mode will be canceled if no action is taken for
over 10 seconds.
•
•
•
20-EN
Download from Www.Somanuals.com. All Manuals Search And Download.
To easily recall adjusted and stored contents
Setting an Amplifier Link (CDA-9831 only)
1) Press MENU to select A-Link.
With an external Amplifier Link compatible amplifier MRD-M501 or
MRD-M301 is connected, the amplifier settings are adjustable from
the head unit. A maximum of 8 external amplifiers can be adjusted.
2) Press g or f to select AMP 1 to 8.
3) Turn the Rotary encoder to select Preset 1 or Preset 2.
4) Press MENU to select RETURN. The unit returns to
normal mode.
Pressing and holding MENU for at least 2 seconds will
return to normal mode.
Press and hold MENU for at least 2 seconds.
1
Press MENU to select A-Link.
2
Press g or f to select AMP1 to 8, or BASS
VOLUME.
3
•
•
For details of each of the settings, refer to the Owner's Manual of
the external amplifier.
If amplifier settings are made on the CDA-9831 model, do not then
change the setting with the amplifier buttons as the amplifier
display may not match the operations of the CDA-9831 model.
"NO Link" is displayed if the amplifier is removed or its power
cannot be turned on, etc.
To set the BASS VOLUME
•
Turn the Rotary encoder to adjust the level, then
press the Rotary encoder.
4
Displaying the External Amplifier Information
(CDA-9831 only)
When an external Amplifier Link compatible amplifier is connected,
the external amplifier's information (voltage, electric current,
temperature) can be shown in the display of the head unit.
When the adjustment has been completed, press
MENU to select RETURN.
The unit returns to normal mode.
Pressing and holding MENU for at least 2 seconds will
return to normal mode.
5
To set the Amplifier
Press TITLE
the display of the external amplifier information.
in the Radio or CD mode to switch
1
Press BAND/TEL. to select from the following
setting items to be adjusted.
4
•
For switching the display, refer to the section "Displaying the Title/
Text" (page 19).
For changing the XM display, refer to the section "Changing the
Display (page 27).
INPUT → LOW PASS → SUBSONIC → P-EQ → BASS COMP
→ T.CORR → PHASE → TURN ON DELAY→ OUTPUT
DISABLE (SAFE) → INPUT
•
Turn the Rotary encoder to change the settings.
5
Voltage Display
Press the Rotary encoder.
6
Repeat steps 5 and 6 (above) if there are other items to
set in step 4.
AMP
12.4V 25.6A
75.0°F
Repeat the steps 4 to 6 (above) if other settings will
be adjusted.
7
Temperature
Display
Electric current
Display
To set another amplifier, return to the step 3.
To store the adjusted contents
This indicator is lit when the Amplifier Link is set.
1) While adjusting the mode, press and hold either button
(1 or 2) for at least 2 seconds.
The adjusted contents are stored.
This indicator is lit when external amplifier
information is displayed.
To recall adjusted and stored contents
•
To switch the display between Celsius and Fahrenheit, refer to
page 25.
1) While adjusting the mode, press either button (1 or 2).
The adjusted and stored contents are recalled.
When adjustment has been completed, press
MENU to select RETURN.
8
The unit returns to normal mode.
Pressing and holding MENU for at least 2 seconds will
return to normal mode.
21-EN
Download from Www.Somanuals.com. All Manuals Search And Download.
Verifying the Software Version
Current version software can be verified in the display.
Setting the Multicolor Illumination
(CDA-9831 only)
You can change the lighting color of the following four buttons:
SOURCE/POWER, BAND/TEL, g and f.
Press and hold MENU for at least 2 seconds.
1
Press MENU to select Information (INFO for
CDA-9830).
The version is displayed.
2
Press MENU to select Illumination.
1
2
Press g or f to select your desired color.
BLUE ↔ GREEN ↔ AMBER ↔ RED ↔ (USER'S*) ↔ BLUE
Press MENU to select RETURN.
The unit returns to normal mode.
Pressing and holding MENU for at least 2 seconds will
return to normal mode.
3
* You can use your desired colors as shown below if you have
already registered to USER'S.
If you want to use colors other than the above
Turn the Rotary encoder to select colors (1
through 512).
3
Each press of BAND advances the color number by 30.
.............. ..............
.............. ..............
363 512
1
19 184
(Red)
(Amber)
(Green)
(Blue)
To store the setting contents
1) While setting the mode, press and hold any one of the
preset buttons (1 through 6) for at least 2 seconds.
The setting contents are stored.
To recall the stored color setting
1) While setting the mode, press any one of the preset
buttons (1 through 6).
The stored setting contents are recalled.
When the setting has been completed, press
MENU to select RETURN.
4
The unit returns to normal mode.
Pressing and holding MENU for at least 2 seconds will
return to normal mode.
• "No Memory" is displayed if a preset that has not been stored is
recalled.
Changing the Lighting Color of All the Buttons
(CDA-9831 only)
You can change the lighting color of the unit.
Press MENU to select Illumination.
1
Press SOURCE/POWER.
The lighting color of all the buttons are changed.
2
AMBER ON ↔ AMBER OFF(green)
When the setting has been completed, press
MENU to select RETURN.
3
The unit returns to normal mode.
Pressing and holding MENU for at least 2 seconds will
return to normal mode.
• SOURCE/POWER, BAND/TEL, g and f buttons are
changed to that which you have set above in "Setting the Multicolor
Illumination" (this page).
22-EN
Download from Www.Somanuals.com. All Manuals Search And Download.
Data Downloading
i-Personalize™
Operation (CDA-9831 only)
Insert the CD-R disc containing the data.
If the source is not the CD mode, press SOURCE/
POWER to change to CD mode.
1
Press MENU to select the Download mode.
2
SOURCE/
POWER
Rotary encoder
Press g or f to select “YES.”
Data search of the disc starts and the first file name is
displayed.
3
•
Selecting “NO” and pressing MENU will cancel the download
mode.
•
•
If a file is not found by the data search, “No File” is indicated.
The “No File” display will automatically disappear if no operation
is performed for 5 seconds.
g
f
MENU
Turn the Rotary encoder to select files that are
downloaded and then press the Rotary encoder
to start.
Data downloading starts.
If the MENU is pressed while downloading, download is
canceled.
4
5
About i-Personalize™
You can download data (from Alpine’s website) to a CD-R and
download and store the data to the CDA-9831.
To start i-Personalize, access the URL below and follow the on-screen
instructions.
When data download is finished successfully, the
confirmation screen of each item is displayed for 2
seconds.
Successfully downloaded items are indicated as checked
boxes on the confirmation screen.
Downloadable data
PARAMETRIC EQ data
Parametric
equalizer
Data is memorized in Preset 2 of the
Parametric EQ mode.
The data is memorized in Preset 2 of Parametric EQ mode.
The memorized data settings in Preset 2 (Parametric EQ
mode) are automatically applied.
Time correction
Data is memorized in Preset 2 of the
Time Correction mode.
HPF/LPF (Cross over) data
The data is memorized in Preset 2 of HPF/LPF mode. The
memorized data settings in Preset 2 (HPF/LPF mode) are
automatically applied.
Crossover
Data is memorized in Preset 2 of the
crossover mode.
TIME CORRECTION data
The data is memorized in Preset 2 of the Time correction
mode. The memorized data settings in Preset 2 (Time
Correction mode) are automatically applied.
The file name of download data shall be
“A_W*****.MP3.”
A_W∗∗∗∗∗.MP3
Press MENU to select RETURN.
6
The display returns to normal mode.
Pressing and holding MENU for at least 2 seconds will
return to normal mode.
Extender (fixed)
Identifier (alphabet or number 5
letters maximum)
•
When you download the data again, the data is overwritten in
Preset.
Header (fixed)
You can create a file name via the website. Do not change a
file name once it has been created. Malfunction may result.
•
•
For details about procedures of download, see ALPINE’s Web site.
If the HDA-5460 model is connected to this unit, the HDA-5460
hard disc can be used. Data that has been stored in the hard disc is
downloaded by the “Data Downloading” operation to CDA-9831.
For details on how to download data to the hard disc, refer to the
Owner’s Manual of the HDA-5460 model.
•
If an external audio processor is connected, data that is
downloaded cannot be used.
23-EN
Download from Www.Somanuals.com. All Manuals Search And Download.
Sound Customizing
SETUP
Switching the Tuner Mode
TUNER MODE NORMAL (Initial setting) / HI-FI / STABLE
You can flexibly customize the unit to suit your own preferences and
usage. Choose the SETUP menu from Sound Customizing, Visual
Customizing, etc., to select your desired setting.
This unit incorporates the MAX TUNE SQ for the highest quality
tuner audio. Moreover, you can choose between three settings to suit
your own personal sound preferences and usage.
NORMAL: Standard setting
HI-FI: Sound quality priority setting
STABLE: Noiseless priority setting
SOURCE/
POWER
BAND/
TEL.
Rotary encoder
•
If you find the sound is very noisy while listening to the tuner in Hi-
Fi mode, we recommend you change to Normal mode.
Subwoofer On and Off
SUBWOOFER ON (Initial setting) / SUBWOOFER OFF
When the subwoofer is on, perform the steps below to adjust the
subwoofer output phase and level.
g
f
MENU
1 Press the Rotary encoder repeatedly to select the
SUBW mode.
SUBW → BALANCE → FADER → DEFEAT → VOLUME →
The common operation for SETUP is step 1 to 4 as
follows. See down below for further information
about each SETUP menu.
SUBW
2 Press g or f.
The subwoofer output phase is toggled SUBW
NORMAL (0°) or SUBW REVERS (180°).
To adjust the level, turn the Rotary encoder.
Press MENU to select the SETUP mode.
SETUP mode is activated.
1
Sound (Beep) Guide Function
BEEP ON (Initial setting) / BEEP OFF
Press g or f to select the desired SETUP
menu.
2
(e.g. Select BEEP)
This function will give audible feedback with varying tones
depending upon the button pressed.
CDA-9831
CLOCK*1 ↔ TUNER MODE ↔ DIMMER ↔ SUBWOOFER ↔
PLAY MODE ↔ BEEP ↔ TEXT SCROLL ↔ INT MUTE ↔ INT
AUDIO ↔ AUX IN ↔ (AUX NAME)*2↔ POWER-IC ↔ LCD
CONTRAST ↔ TUNER AREA*3 ↔ A-LINK TEMP*4 ↔ DEMO
↔ CLOCK*1
Visual Customizing
Dimmer Control (CDA-9831 only)
DIMMER AUTO (Initial setting) / DIMMER MANUAL
Set the DIMMER control to AUTO to decrease the illumination
brightness of the unit with the head lights of the vehicle ON.This
mode is useful if you feel the unit's backlighting is too bright at night.
CDA-9830
CLOCK*1 ↔ NORMAL/HI-FI/STABLE ↔ SUBW ↔ CD-DA/
CDDA/MP3 ↔ BEEP ↔ SCR ↔ MUTE ↔ INT ↔ AUX ↔ (AUX
NAME)*2 ↔ PWR ↔ AREA ↔ DEMO ↔ CLOCK*1
Scroll Setting
TEXT SCROLL AUTO / TEXT SCROLL MANUAL (Initial setting)
*1 Refer to the “Setting Time” section (page 6).
*2 Displayed only when AUX is ON.
This CD player can scroll the disc and track names recorded on CD-
TEXT discs, as well as the text information of MP3/WMA files,
folder names, and tags.
*3 Refer to the “Radio” section (page 8)
*4 Displayed only when an external amplifier is connected.
SCROLL AUTO : The CD text information, the text information
of folder and file names, and the tags are scrolled
automatically.
Turn the Rotary encoder to change the setting.
(e.g. Select BEEP ON or BEEP OFF.)
3
SCROLL MANUAL : The display is scrolled when a disc is
loaded or when a track is changed, etc.
Press MENU to select RETURN.
4
The display returns to normal mode.
Pressing and holding MENU for at least 2 seconds will
return to normal mode.
•
The unit scrolls CD text names, folder names, file names or tag
display. The disc titles input manually (page 20) cannot be
scrolled.
•
•
For the XM Radio settings, refer to “XM Radio (Optional)” (page
26), and for the MobileHub™Link settings, refer to
“MobileHub™Link Operation (Optional)” (page 28).
If no operation is performed within 15 seconds, the display returns
to normal mode.
24-EN
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting Display Contrast (CDA-9831 only)
LCD CONTRAST
Connecting to an External Amplifier
POWER-IC ON (Initial setting) / POWER-IC OFF
You can adjust the display contrast for better visibility.
When an external amplifier is connected, sound quality can be
improved by stopping the power supply of the built-in amplifier.
You can adjust in a range of - 5 and + 5.
POWER-IC OFF : Use this mode when the front and rear pre-
amplifier of the unit are used to drive an external amplifier
connected to the speakers. In this setting, the head unit’s
internal amplifier has no output to drive speakers.
•
The initial setting at the factory is “0.”
Demonstration
DEMO ON / DEMO OFF (Initial setting)
Front
left
This unit has a demonstration feature for the display and sound, and
the CDA-9830 has a demonstration feature only for the sound.
Amplifier
Front
•
To quit Demo mode, set to DEMO OFF.
right
Rear
left
MP3/WMA
Amplifier
Playing MP3/WMA Data
PLAY MODE CD-DA (Initial setting) / PLAY MODE CD-DA &
Rear
right
MP3
This product can playback CDs containing both CD and MP3/WMA
data. However, in some situations (some enhanced CDs), playback
may be difficult. For these special cases, you can select playback of
CD data only. When a disc contains both CD or the MP3/WMA data,
playback starts from the CD data portion of the disc.
POWER-IC ON : The speakers are driven by the built-in amplifier.
Speakers
SPEAKER
RIGHT FRONT
Front
CD-DA : Only CD data can be played back.
CD-DA & MP3 : Both CD data and MP3/WMA file tracks can
be played back.
right
SPEAKER
RIGHT REAR
•
Perform this setting before inserting a disc. If a disc has already
been inserted, perform the setting after you remove the disc. (If you
use an MP3 changer, you have to change discs.)
Rear
right
SPEAKER
LEFT REAR
Rear
External Device
left
Turning Mute Mode On/Off
INT MUTE ON (Initial setting) / INT MUTE OFF
SPEAKER
Front
left
LEFT FRONT
If a device having the interrupt feature is connected, audio will be
automatically muted whenever the interrupt signal is received from
the device.
•
No sound is produced by the system when the power output is
set to OFF.
Setting the AUX Mode (V-Link)
AUX IN ON / AUX IN OFF (Initial setting)
Setting the Temperature Display for the
External Amplifier (CDA-9831 only)
A-LINK TEMP °F(Initial setting) / °C
You can input TV/video sound by connecting an optional Ai-NET/
RCA Interface cable (KCA-121B) or Versatile Link Terminal (KCA-
410C) to this component.
You can change the AUX name display when AUX ON is set. Select
the AUX name by pressing g or f. Then turn the Rotary
encoder.
When a separately sold Amplifier Link compatible amplifier is
connected, you can set how to display its temperature. You can switch
the setting between Fahrenheit and Celsius.
If the KCA-410C is connected, it is possible to select two AUX
names.
°F : The temperature is displayed in Fahrenheit.
°C : The temperature is displayed in Celsius.
•
Via KCA-410C, up to 2 external devices with RCA output can be
connected. In this case, press SOURCE/POWER to select AUX
mode and then press BAND/TEL. to select your desired device.
Setting the Tone Defeat for External Devices
INT AUDIO ON / INT AUDIO OFF (Initial setting)
When inputting external devices to this unit, turning tone defeat on
will bypass EQ and MX, i.e., sound for external devices is output at
the default setting.
25-EN
Download from Www.Somanuals.com. All Manuals Search And Download.
Checking the XM Radio ID Number
You need to provide XM with the unique XM Radio ID number for
XM Radio (Optional)
your XM Radio Receiver in order to subscribe to XM's programming.
SOURCE/
POWER
BAND/
TEL.
This number is an 8 character alphanumeric number that is printed on
a label directly on the XM Receiver.
SEARCH
TITLE
8
It can also be displayed on the screen of the CDA-9831/CDA-9830 in
the following way.
While receiving XM1, XM2 or XM3, press g or
f to select channel “0.”
1
The unit alternately displays “RADIO ID” for 2 seconds,
then the ID number for 10 seconds.
While displaying "RADIO ID" as shown above, Blackout
(page 20) and Demonstration (page 25) become
nonfunctional.
Preset buttons
(1 through 6)
Rotary
encoder
g MENU f
9
To cancel the ID number display, set the channel to
other than “0.”
2
Receiving XM Channels with the XM
Receiver (Optional)
XM Satellite Radio* is the next generation of audio entertainment,
with up to 100 brand-new digital channels. For a small monthly fee,
subscribers can hear crystal-clear music, sports, news and talk, coast-
to-coast via satellite. For more information, visit XM’s website at
•
•
You cannot use “O,” “S,”“ I,” or “F” for the ID Number.
You can check your ID number printed on the label on the package
of your XM Satellite Radio Receiver (TUA-T020XM).
Storing XM Channel Presets
Press BAND/TEL. to select the desired band (XM1,
XM2 or XM3) you want to store.
1
An optional XM Satellite Radio Receiver (TUA-T020XM) and an
optional XM antenna may be connected to the CDA-9831/CDA-9830.
With an XM Receiver connected to the Ai-NET input of the CDA-
9831/CDA-9830, the XM Receiver will be controllable from the
CDA-9831/CDA-9830.
After tuning in the desired channel, press and hold,
2
for at least 2 seconds, any one of the preset
buttons (1 through 6) into which you wish to
store the channel.
* XM and its corresponding logos are trademarks of XM Satellite
Radio Inc.
The selected station is stored.
•
•
The controls on the CDA-9831/CDA-9830 for XM Receiver
operation are operative only when an XM Receiver is connected.
The XM1, XM2 or XM3 band illuminates when in XM mode.
Repeat the procedure to store up to 5 other
channels onto the same band.
3
•
•
•
To use this procedure for other bands, simply select the band
desired and repeat the procedure.
Press SOURCE/POWER to select XM mode.
1
2
A total of 18 channels can be stored in the preset memory (6
channels for each band; XM1, XM2 and XM3).
If you store a channel in a preset memory which already has a
station, the current channel will be cleared and replaced with the
new one.
Press BAND/TEL. to select XM1, XM2 or XM3.
Each press changes the band:
XM1 → XM2 → XM3 → XM1
Press 8 or 9 to select desired category.
Holding down 8 or 9 will change categories
continuously.
3
Receiving Stored XM Channels
Press BAND/TEL. to select the desired band (XM1,
XM2 or XM3).
1
Press g or f to select the desired channel.
Holding down g or f will change channels
continuously.
4
XM1 → XM2 → XM3 → XM1
Press the channel preset button that has your
desired satellite channel in memory.
2
•
When using the optional remote control (RUE-4190), an XM
Channel can be directly called up with the numeric keypad of the
remote control.
1 While in XM Radio mode, enter the Channel number you
want to call up with the numeric keypad on the remote
control.
2 Press ENTER or + 10/OK on the remote control within 5
seconds to receive the XM Channel.
If the channel number is 3 digits, the XM Channel is
automatically received after the channel number is input.
26-EN
Download from Www.Somanuals.com. All Manuals Search And Download.
•
When the "Scroll Setting" (page 24) is set to "SCROLL AUTO," the
display scrolls continuously.
When the Scroll Setting is set to "SCROLL MANUAL," the display
scrolls only once after any function is performed (PRESET, BAND,
SEARCH, etc.).
Channel/Category Search Function
You can search for programs by Channel No. or Category.
Press SEARCH
Channel Search mode or Category Search mode.
in the XM mode to select
1
Press and hold TITLE for more than 2 seconds to scroll the
display manually.
•
•
“Channel Number” and “Clock” displays do not scroll.
Depending on the model, the display may differ from the one
shown above.
Channel Search mode:
•
When displaying the Music Title/Channel Name, the number 6,
described in the section “About the indicator display” (page 19), is
lit. When displaying the Artist Name, the number 4, described in
the section “About the indicator display” (page 19), is lit.
Turn the Rotary encoder to select the desired
Channel No.* within 10 seconds.
* The Channel No. is selected within the selected Category.
2
Press Rotary encoder to receive the selected
Channel No.
3
Setting the Tuning Method
•
•
•
Search mode is canceled by pressing and holding SEARCH for
at least 2 seconds in Channel Search mode.
While in Channel Search mode, press 8 or 9 to select the another
Category.
While in Channel Search mode, press SEARCH to switch to the
Category Search mode.
You can set the tuning method. You can select the received stations in
channel no. order or in channel name order (alphabetic order).
Press MENU to select the SETUP mode.
1
Press g or f to select “CH SELECT”
(“CH NO” or “ALPHABET” for CDA-9830).
2
Category Search mode:
Turn the Rotary encoder to set the tuning
method.
3
Turn the Rotary encoder to select the desired
Category within 10 seconds.
2
3
CH NO :
Set in order of channel no.
ALPHABET : Set in alphabetic order.
Press Rotary encoder to receive the selected
Category.
Press MENU to select RETURN.
The unit returns to normal mode.
Pressing and holding MENU for at least 2 seconds will
return to normal mode.
4
•
Search mode is canceled by pressing and holding SEARCH for
at least 2 seconds in Category Search mode.
While in Category Search mode, press SEARCH to switch to
Channel Search mode.
•
•
When the setting is completed, switch the channel DOWN/UP by
pressing the g or f.
Quick Search Function
You can search for all Channels.
Setting the Auxiliary Data Field Display
The XM Auxiliary Data Field (ADF) display can be switched on or
off.
1
Press and hold SEARCH
in XM mode to activate Quick Search mode.
for at least 2 seconds
Press MENU to select the SETUP mode.
1
2
Turn the Rotary encoder to select the desired
Channel within 10 seconds.
The selected Channel is received.
2
Select “XM ADF (ADF for CDA-9830)” by pressing
g or f.
Select ON/OFF by turning the Rotary encoder.
3
Changing the Display
Text information, such as the channel name, artist name/feature, and
song/program title, is available with each XM channel. The unit can
display this text information as explained below.
When setting to ON, Auxiliary Data Field is displayed by
pressing TITLE . (Refer to the “Changing the Display”
section on this page.)
Press MENU to select RETURN.
The unit returns to normal mode.
Pressing and holding MENU for at least 2 seconds will
return to normal mode.
4
In XM mode, press TITLE
.
Each time you press this button, the display changes as shown
below.
Channel Number*1 → Channel Name → Music Title → Artist
Name → Auxiliary Data Field*2 → Clock → External Amplifier
Information*3 → Channel Number*1
*1 The Channel Name display automatically changes after 2 seconds.
*2 When ADF is turned OFF, this information is not displayed (see
“Setting the Auxiliary Data Field Display” on this page).
*3 CDA-9831 only
Refer to the “Displaying the External Amplifier Information”
section (page 21).
27-EN
Download from Www.Somanuals.com. All Manuals Search And Download.
•
An outgoing call from a portable telephone is also possible.
However, you cannot perform different operations at the same time
from a portable telephone and CDA-9831/CDA-9830 as
malfunction can result.
MobileHub™ Link
Operation(Optional)
•
•
•
With a junction box connected outgoing, incoming, and sending
history will also be recorded in the portable telephone.
While telephoning, defeat is set to ON. When the call has finished,
the unit returns to your previous setting.
The telephone volume can be adjusted on the CDA-9831/CDA-
9830. The volume you set during the call is memorized, and is
automatically applied again on the next call.
BAND/
TEL.
SOURCE/
POWER -/J
TITLE
SEARCH
8
•
While telephoning or receiving incoming calls, press TITLE to
show the Network Operator display for 5 seconds.
Incoming Calls
Press :/J to receive an incoming call.
1
Press BAND/TEL. to finish a call.
Telephone mode will end and return to the original source
2
Rotary
encoder
f
9
g MENU
Preset buttons
(1 through 6)
F
mode.
•
When the Automatic Calling mode is on, you can talk after 3
seconds of receiving the incoming call. (See “Setting the Automatic
Calling” described below.)
About MobileHub™ Link
Connect a separately sold junction box and a portable telephone
(available from Nokia) to control the incoming and outgoing calls of
the portable telephone.
Setting the Automatic Calling
The incoming call can be switched to Automatic Calling or Manual
Caution
Even with hands-free operation, a driver can be distracted during
telephone operation or receiving a call. For the sake of safety,
drivers are requested to refrain from operating the telephone
while driving.
For the sake of safety, only incoming calls and Speed-Dial
outgoing calls can be operated.
Calling.
Press MENU to select the SETUP mode.
1
2
Select the TELEPHONE (TEL for CDA-9830) mode
by pressing g or f.
•
•
If a portable telephone is connected, its address book, incoming
and outgoing history are downloaded to the junction box.
Please refer to the instruction manual of the junction box.
Turn the Rotary encoder to change to AUTO or
MANUAL (MANU for CDA-9830).
3
Press MENU to select RETURN.
The unit returns to normal mode.
Telephone Mode ON/OFF
4
Pressing and holding MENU for at least 2 seconds will
return to normal mode.
Press and hold BAND/TEL. for at least 2 seconds to
turn on the Telephone mode.
To turn off, press BAND/TEL.
See relevant pages for each item.
•
•
Press BAND/TEL. during an incoming call to disconnect it.
The initial setting of the factory is MANUAL.
•
•
•
•
•
“NO PHONE” is displayed for about 2 seconds, if a portable
telephone is not connected, before entering the telephone mode.
Then the mode returns to the original source mode
When the portable telephone is taken off the junction box during an
incoming or outgoing call, or during a hands-free call, the call will
be treated as an ordinary one by the portable telephone.
When there is an incoming call while the power of CDA-9831/
CDA-9830 is off, the power of CDA-9831/CDA-9830 will turn on
automatically for a hands-free call.
Even if the power of the portable telephone is off, when CDA-9831/
CDA-9830 is set to Telephone mode, the power of the portable
telephone will be turned on.
Even if the ACC power of the vehicle is turned off (even if the
engine is stopped) during a hands-free call, the call is not
disconnected, and an ordinary call by the portable telephone is
possible.
•
If there is an incoming call during operation (except an outgoing
call or talking), operation mode will end and switch to the
incoming or talking mode.
28-EN
Download from Www.Somanuals.com. All Manuals Search And Download.
Calling by the outgoing/incoming/absent incoming history
Calling
You can place a call to any of the last 999 calls by the outgoing/
incoming/absent incoming history.
Calling by the address book
You can call up the address book registered in the portable telephone
to call from.
Press SEARCH
the History mode.
in Phone Book mode to select
1
2
Press and hold BAND/TEL. for at least 2 seconds.
1
Press 8 or 9 to select outgoing history (display
example:“DIALED”), incoming history (display
example:“RECEIVE” ), absent incoming history
(display example:“MISSED”).
2
Press SEARCH
A list in alphabetic order is displayed.
to select Phone Book mode.
Turn the Rotary encoder, or press g or f to
select the addressee from the outgoing or
incoming history.
Retrieving an addressee by Alphabetic Sort List
3
When displaying the Alphabetic Sort List, turn the
3
Rotary encoder or press g or f to select
the addressee.
Press :/J or the Rotary encoder to place a call.
4
5
Press :/J or Rotary encoder to place a call.
4
5
Press BAND/TEL. to end the call.
Telephone mode will end and return to the original source
mode.
Press BAND/TEL. to end the call.
Telephone mode will end and return to the original source
mode.
•
•
If all telephone numbers and registered names cannot be displayed
at once, press TITLE
to show undisplayed numbers and names.
Retrieving an addressee by Selecting Search (A-Z search)
“NO MEMORY” (“NO MEM” for CDA-9830) is displayed if there
is no history.
Press 8 or 9 to select an initial letter (A to Z) of the
addressee.
3
SMS (Short Message Service) Operation
You can be informed when you receive a short message.
Turn the Rotary encoder to select the addressee.
4
5
Press the Rotary encoder to place a call.
Receiving a short message
Press BAND/TEL. to end the call.
Telephone mode will end and return to the original source
6
When a text message is received,“NEW
MESSAGE” for CDA-9831, or “NEW MSG” for CDA-
9830 is indicated on the display.
The contents of the received message can only be read
from the portable phone's display.
1
mode.
•
•
If all telephone numbers and registered names cannot be displayed
at once, press TITLE to show undisplayed numbers and names.
“NO MEMORY” (“NO MEM” for CDA-9830) is displayed if
nothing is registered in the Phone Book.
Press any one of the buttons on the unit to cancel
the display.The buttons that are pressed will enter
the mode or will be activated.
2
Calling by using the Speed Dial
You can place a call by retrieving one of the telephone numbers
registered in No. 1 to 9 of the address book.
Press and hold BAND/TEL. for at least 2 seconds.
1
Within 5 seconds, place a call by pressing and
holding the desired preset button (1 through 6)
for at least 2 seconds.
2
By pressing F, and then pressing a preset button
(1 through 3) for at least 2 seconds, you can
place a call to the number registered in 7 to 9.
•
•
You can place a call by pressing :/J after momentarily pressing
the preset button (1 through 6) of the number you wish to call.
You can place a call by pressing the Rotary encoder, after selecting
a number which you wish to call, by pressing g or f , or by
turning the Rotary encoder.
Press BAND/TEL. to end the call.
Telephone mode will end and return to the original source
mode.
3
•
If there is no telephone number registered to a preset button, “NO
PRESET” (“NO P-SET” for CDA-9830) is displayed when you try
to place a call.
29-EN
Download from Www.Somanuals.com. All Manuals Search And Download.
Playing MP3 Files with the CD Changer
(Optional)
If you connect a changer compatible with MP3, you can play CD-
ROMs, CD-Rs, and CD-RWs containing MP3 files on this unit.
Changer (Optional)
SOURCE/
BAND/TEL.
POWER
-/J
Press SOURCE/POWER to switch to the MP3
Changer mode.
1
Press any one of the disc select buttons (1
through 6) corresponding to one of the discs
2
loaded in the CD Changer.
To pause playback, press -/J.
Pressing -/J again will resume playback.
3
F
Select buttons (1 through 6)
•
•
The unit can play discs containing both audio data and MP3 data.
For operating MP3 with an MP3 compatible CD Changer, refer to
“CD/MP3/WMA” pages 9 to 13.
Controlling CD Changer (Optional)
An optional 6-disc or 12-disc CD Changer may be connected to this
unit if it is Ai-NET compatible. With a CD Changer connected to the
Ai-NET input of this unit, the CD Changer will be controllable from
this unit.
Using the KCA-400C (Multi-Changer Switching device) or the KCA-
410C (Versatile Link Terminal) multiple changers can be controlled
by this unit.
Multi-Changer Selection (Optional)
Alpine's Ai-NET system will support up to 6 CD Changers. When
operating two or more changers, the KCA-400C (Multi-Changer
Switching device) must be used. If you use 1 Switching device, you
can connect up to 4 CD Changers. If you use 2 Switching devices,
you can connect up to 6 CD Changers. When using KCA-410C
(Versatile Link Terminal), you can connect two changers and two
external outputs (AUX).
See “Multi-Changer Selection” on this page for selecting the CD
Changers.
•
•
The controls on this unit for CD Changer operation are operative
only when a CD Changer is connected.
The DVD changer (optional) is controllable from this unit as well
as the CD changer.
Press SOURCE/POWER on this unit to activate
the CD Changer mode.
1
Alternatively, press SOURCE on the remote control (RUE-
4187) to activate the CD Changer mode.
Press SOURCE/POWER to activate the CHANGER
mode.
1
The display shows the disc number and track number.
•
•
The source indicator varies depending on the connected source.
Press BAND/TEL. to switch the Disc mode in the CD/Changer
mode.
BAND
SOURCE
Press the disc select buttons (1 through 6)
corresponding to one of the discs loaded in the CD
Changer.
2
The selected disc number appears in the display and CD
playback starts.
Press BAND/TEL. on this unit or the RUE-4187 to
activate the CD Changer Selection mode.
The CD Changer Selection mode remains active for 8
seconds.
2
3
•
•
•
After selecting the desired disc, you can operate in the same way as
for the CD player of this unit.
For details, please see the CD/MP3/WMA section.
If the “FUNC” indicator is illuminated, the disc select buttons
become nonfunctional.
Press BAND/TEL. until the desired CD Changer
indicator appears on the display.
When a 12-disc CD Changer is connected:
To select discs numbered from 1 to 6, the procedure is the
same as for the 6-disc CD Changer. To select discs
numbered from 7 to 12, first press F. This changes the “D”
indicator to “d.” Then press the desired preset button.
With F activated, the preset buttons 1 to 6 will represent
discs 7 to 12 respectively.
Alternatively press BAND/TEL. on the Remote Control until
the desired changer indicator appears on the display.
If the selected CD Changer is not connected, the display will show
“NO CHANGER “ (“NO CHGR” for CDA-9830).
To operate the selected changer, see “CD/MP3/WMA”(page 9).
For further details about the external input (AUX) when using
KCA-410C, see “Setting the AUX Mode (V-Link)” on page 25.
•
•
30-EN
Download from Www.Somanuals.com. All Manuals Search And Download.
9
!
f UP Button
Radio mode: SEEK (UP) button
CD mode: Press this button to advance to the beginning
of the next track.
Remote Control
9 Button
1
2
Radio mode: Pressing this button will select, in
descending order, stations programmed into the radio's
presets as shown below.
5
6
7
8
9
!
6 → 5 ... 1 → 6
CD Changer mode: DISC Select (DN) button
Press this button to select a disc in descending order.
MP3/WMA mode: Folder or Playlist Select (DN) button
Press this button to select the folder or playlist.
3
4
"
#
"
#
Mute Button
Press this button to lower the volume by 20 dB instantly.
Press this button again to cancel.
Audio Processor Button
Each press of the button changes the audio processor
mode.
Controls on Remote Control
For details, refer to "Operating the Audio Processor" as
shown below.
1
2
3
Power Button
Press this button to turn the power on/off.
Press the button to call the external audio processor
mode when the external audio processor is connected.*1
Source Button
Press this button to select the audio source.
*1 For the operation of external audio processor, refer to the Owner's
Manual of the external audio processor you purchased.
-/J Button
Press this button to switch between the Play and Pause
modes for CD.
Operating the Audio Processor
4
5
TILT 98 Buttons
Press this button to adjust the angle of the movable
display.
Press A.PROC to select the mode.
1
Normal mode → EQ mode (Equalizer Presets) → Time
Correction mode (Recalling the Stored Time Correction) →
Crossover mode (Recalling the Stored built-in Crossover) →
Normal mode
Band/Program Button
Radio mode: BAND Button
Press this button and the band will change.
Press 8 or 9 to select the item.
2
CD/Changer mode: To switch the disc mode.
EQ mode:
6
7
Volume Adjustment Buttons
To increase the volume level:
Press the L button
Select from FLAT(OFF), ROCK, POPS, JAZZ & BLUES
(JAZZ), ELECTRICAL (ELECTRIC), HIPHOP & RAP
(HIPHOP), EASY LISTEN (EASY), COUNTRY, CLASSICAL
(CLASSIC), NEWS, USER'S EQ 1,2 (USERS 1,2).
Time Correction mode/Built-in Crossover mode:
Select from MEMORY 1 or 2.
To decrease the volume level:
Press the K button
8 Button
Radio mode: Pressing this button will select, in ascending
order, stations programmed into the radio's presets as
shown below.
1 → 2 ... 6 → 1
CD Changer mode: DISC Select (UP) button
Press this button to select a disc in ascending order.
MP3/WMA mode: Folder or Playlist Select (UP) button
Press this button to select the folder or playlist.
8
g DN Button
Radio mode: SEEK (DN) Button
CD mode: Press this button to go back to the beginning of
the current track.
31-EN
Download from Www.Somanuals.com. All Manuals Search And Download.
Battery Replacement
Applicable battery: Use two “AAA” sized dry batteries or equivalent.
Information
In Case of Difficulty
Opening the battery cover
Slide out the battery cover while firmly pressing in the
1
If you encounter a problem, please turn the power off, then on again.
If the unit is still not functioning normally, please review the items in
the following checklist. This guide will help you isolate the problem
if the unit is at fault. Otherwise, make sure the rest of your system is
properly connected or consult your authorized Alpine dealer.
direction of the arrow.
Basic
No function or display.
•
Vehicle's ignition is off.
- If connected following instructions, the unit will not
operate with the vehicle's ignition off.
Improper power lead connections.
- Check power lead connections.
Blown fuse.
Replacing the battery
Insert the batteries, observing the polarities as illustrated.
2
•
•
- Check the fuse on the battery lead of the unit; replace with
the proper value if necessary.
•
Internal micro-computer malfunctioned due to interference
noise etc.
- Press the RESET switch with a ballpoint pen or other
pointed article.
Closing the cover
Slide the cover as illustrated until a click is heard.
3
Radio
Unable to receive stations.
•
No antenna or open connection in cable.
- Make sure the antenna is properly connected;
replace the antenna or cable if necessary.
Unable to tune stations in the seek mode.
•
You are in a weak signal area.
- Make sure the tuner is in the DX mode.
•
If the area you are in is a primary signal area, the antenna may
not be grounded and connected properly.
- Check your antenna connections; make sure the antenna is
properly grounded at its mounting location.
The antenna may not be the proper length.
- Make sure the antenna is fully extended; if broken, replace
the antenna with a new one.
Point the remote control transmitter at the remote control
sensor.
•
Remote control sensor
Broadcast is noisy.
•
The antenna is not the proper length.
- Extend the antenna fully; replace it if it is broken.
The antenna is poorly grounded.
•
- Make sure the antenna is grounded properly at its mounting
location.
32-EN
Download from Www.Somanuals.com. All Manuals Search And Download.
CD
Indication for CD Player
CD Player/Changer not functioning.
HIGH-TEMP
HI TEMP
•
Out of operating temperature range +50˚C (+120˚F) for CD.
- Allow the vehicle's interior (or trunk) temperature to cool.
(CDA-9831)
(CDA-9830)
•
Protective circuit is activated due to high temperature.
- The indicator will disappear when the temperature returns to
within operation range.
CD playback sound is wavering.
•
Moisture condensation in the CD Module.
- Allow enough time for the condensation to evaporate (about
1 hour).
CD insertion not possible.
NO DISC
•
A CD is already in the CD player.
- Eject the CD and remove it.
•
•
No CD is inserted.
- Insert a CD.
Although a disc is inserted, “NO DISC” is displayed and the
unit does not start to play or eject the disc.
- Remove the disc by following these steps:
1) Press the c button.
The movable display will open.
2) Press the c button again for at least 2 seconds while the
movable display is open.
•
The CD is being improperly inserted.
- Make sure the CD is being inserted following instructions in
the CD Player Operation section.
Unable to fast forward or backward the CD.
The CD has been damaged.
- Eject the CD and discard it; using a damaged CD in your unit
can cause damage to the mechanism.
•
CD playback sound skips due to vibration.
•
•
•
•
Improper mounting of the unit.
- Securely re-mount the unit.
The disc is very dirty.
- Clean the disc.
The disc has scratches.
- Change the disc.
The pick-up lens is dirty.
- Do not use a commercial available lens cleaner disc. Consult
your nearest ALPINE dealer.
ERROR
•
Mechanism error.
1) Press the c button and eject the CD.
If not ejecting, consult your Alpine dealer.
2) When the error indication remains after ejecting, press the
c button again.
If the error indication still does not turn off after pressing
the c button for a few times, consult your Alpine dealer.
CD playback sound skips without vibration.
•
When “ERROR” is displayed:
•
The disc is dirty or scratched.
If the disc cannot be ejected by pressing c, press the RESET
switch (refer to page 6) and press c again.
If the disc still cannot be ejected, consult your Alpine dealer.
- Clean the disc; damaged disc should be replaced.
Error displays (built-in CD player only)
•
Mechanical error
- Press c. After the error indication disappears, insert the disc
again. If the above-mentioned solution does not solve the
problem, consult your nearest ALPINE dealer.
PROTECT
•
•
A copy-protected WMA file was played back.
- You can only play back non-copy-protected files.
CD-R/CD-RW playback not possible
Close session (finalization) has not been performed.
- Perform finalization and attempt playback again.
•
UNSUPPORT
(CDA-9831)
The disc is not written in a MP3/WMA supported format.
- Use a disc written at the MP3/WMA supported format.
UNSUPORT
(CDA-9830)
MP3/WMA
MP3 or WMA is not played back.
•
Writing error occurred. The CD format is not compatible.
- Make sure the CD has been written in a supported format.
Refer to “About MP3/WMA” (page 12-13), then rewrite in
the format supported by this device.
33-EN
Download from Www.Somanuals.com. All Manuals Search And Download.
Indication for CD Changer
Indication for XM Radio Mode
HI TEMP
ANTENNA
HIGH-TEMP
(CDA-9831)
(CDA-9830)
•
•
The XM antenna is not connected to the XM radio module.
- Check whether the XM antenna cable is attached securely to
the XM radio module.
•
Protective circuit is activated due to high temperature.
- The indicator will disappear when the temperature returns to
within operation range.
UPDATING
ERROR - 01
Radio is being updated with latest encryption code.
- Wait until encryption code is being updated. Channels
0 and 1 should function normally.
•
•
Malfunction in the CD Changer.
- Consult your Alpine dealer. Press the magazine eject
button and pull out the magazine.
Check the indication. Insert the magazine again.
If the magazine cannot be pulled out, consult your Alpine
dealer.
Magazine ejection not possible.
- Press the magazine eject button. If the magazine does not
eject, consult your Alpine dealer.
NO SIGNAL
NO SIGNL
(CDA-9831)
(CDA-9830)
•
•
•
XM signal is too weak at the current location.
- Wait until the car reaches a location with a stronger signal.
LOADING
ERROR - 02
•
A disc is left inside the CD Changer.
Radio is acquiring audio or program information.
- Wait until the radio has received the information.
- Press the eject button to activate the eject function. When the
CD Changer finishes the eject function, insert an empty CD
magazine into the CD Changer to receive the disc left inside
the CD Changer.
OFF AIR
The channel currently selected has stopped broadcasting.
- Select another channel.
NO MAGZINE
NO MAGZN
(CDA-9831)
(CDA-9830)
•
•
No magazine is loaded into the CD Changer.
- Insert a magazine.
– – – – – –
– – – –
(CDA-9831)
(CDA-9830)
•
•
The user has selected a channel number that does not exist or
is not subscribed to.
- The unit will revert back to the previously selected channel.
There is no artist name/feature, song/program title, or
additional information associated with the channel at that time.
- No action needed.
NO DISC
No indicated disc.
- Choose another disc.
34-EN
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
FM TUNER SECTION
Tuning Range
GENERAL
Power Requirement
14.4 V DC
87.7 – 107.9 MHz
(11–16 V allowable)
18 W RMS × 4*
Mono Usable Sensitivity
50 dB Quieting Sensitivity
9.3 dBf (0.8 µV/75 ohms)
13.5 dBf (1.3 µV/75 ohms)
Power Output
* Primary amplifier ratings per CEA-2006 Standard
• Power output: measured at 4 Ohms and ≤ 1% THD+N
• S/N: 80 dBA (reference: 1 W into 4 Ohms)
Alternate Channel Selectivity 80 dB
Signal-to-Noise Ratio
Stereo Separation
Capture Ratio
80 dB
45 dB
2.0 dB
Maximum Pre-Output Voltage 4 V/10 k ohms
Weight
1.6 kg (3 lbs. 8 oz)
AM TUNER SECTION
Tuning Range
Sensitivity (IEC Standard)
CHASSIS SIZE
Width
Height
530 – 1,710 kHz
22.5 µV/27 dB
178 mm (7")
50 mm (2")
152 mm (6")
CD PLAYER SECTION
Frequency Response
Wow & Flutter (% WRMS)
Total Harmonic Distortion
Dynamic Range
Depth
5 – 20,000 Hz ( 1 dB)
Below measurable limits
0.008% (at 1 kHz)
95 dB (at 1 kHz)
105 dB
NOSEPIECE SIZE
Width
Height
170 mm (6-11/16")
46 mm (1-13/16")
18 mm (11/16")
Depth
Signal-to-Noise Ratio
Channel Separation
85 dB (at 1 kHz)
•
Due to continuous product improvement, specifications and design
are subject to change without notice.
PICKUP
Wave length
795 nm
Laser power
CLASS I
REMOTE CONTROL
Battery Type
Width
Height
Depth
AAA batteries (2 pcs.)
42 mm (1-21/32")
121 mm (4-25/32")
23 mm (29/32")
Weight
50 g (1.8 oz)
35-EN
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation and Connections
Before installing or connecting the unit, please read the
following and pages 3 to 5 of this manual thoroughly
for proper use.
Caution
HAVE THE WIRING AND INSTALLATION DONE BY
EXPERTS.
The wiring and installation of this unit requires special technical
skill and experience. To ensure safety, always contact the dealer
where you purchased this product to have the work done.
Warning
MAKE THE CORRECT CONNECTIONS.
Failure to make the proper connections may result in fire or
product damage.
USE SPECIFIED ACCESSORY PARTS AND INSTALL THEM
SECURELY.
Be sure to use only the specified accessory parts. Use of other
than designated parts may damage this unit internally or may not
securely install the unit in place. This may cause parts to become
loose resulting in hazards or product failure.
USE ONLY IN CARS WITH A 12 VOLT NEGATIVE GROUND.
(Check with your dealer if you are not sure.) Failure to do so may
result in fire, etc.
BEFORE WIRING, DISCONNECT THE CABLE FROM THE
ARRANGE THE WIRING SO IT IS NOT CRIMPED OR
PINCHED BY A SHARP METAL EDGE.
Route the cables and wiring away from moving parts (like the
seat rails) or sharp or pointed edges. This will prevent crimping
and damage to the wiring. If wiring passes through a hole in
metal, use a rubber grommet to prevent the wire’s insulation from
being cut by the metal edge of the hole.
NEGATIVE BATTERY TERMINAL.
Failure to do so may result in electric shock or injury due to
electrical shorts.
DO NOT ALLOW CABLES TO BECOME ENTANGLED IN
SURROUNDING OBJECTS.
Arrange wiring and cables in compliance with the manual to
prevent obstructions when driving. Cables or wiring that obstruct
or hang up on places such as the steering wheel, gear lever, brake
pedals, etc. can be extremely hazardous.
DO NOT INSTALL IN LOCATIONS WITH HIGH MOISTURE
OR DUST.
Avoid installing the unit in locations with high incidence of
moisture or dust. Moisture or dust that penetrates into this unit
may result in product failure.
DO NOT SPLICE INTO ELECTRICAL CABLES.
Never cut away cable insulation to supply power to other
equipment. Doing so will exceed the current carrying capacity of
the wire and result in fire or electric shock.
Precautions
DO NOT DAMAGE PIPE OR WIRING WHEN DRILLING
HOLES.
When drilling holes in the chassis for installation, take
precautions so as not to contact, damage or obstruct pipes, fuel
lines, tanks or electrical wiring. Failure to take such precautions
may result in fire.
•
•
•
Be sure to disconnect the cable from the (–) battery post before
installing your CDA-9831/CDA-9830. This will reduce any
chance of damage to the unit in case of a short-circuit.
Be sure to connect the color coded leads according to the
diagram. Incorrect connections may cause the unit to
malfunction or damage to the vehicle's electrical system.
When making connections to the vehicle's electrical system, be
aware of the factory installed components (e.g. on-board
computer). Do not tap into these leads to provide power for
this unit. When connecting the CDA-9831/CDA-9830 to the
fuse box, make sure the fuse for the intended circuit of the
CDA-9831/CDA-9830 has the appropriate amperage. Failure
to do so may result in damage to the unit and/or the vehicle.
When in doubt, consult your ALPINE dealer.
DO NOT USE BOLTS OR NUTS IN THE BRAKE OR
STEERING SYSTEMS TO MAKE GROUND CONNECTIONS.
Bolts or nuts used for the brake or steering systems (or any other
safety-related system), or tanks should NEVER be used for
installations or ground connections. Using such parts could
disable control of the vehicle and cause fire etc.
KEEP SMALL OBJECTS SUCH AS BATTERIES OUT OF THE
REACH OF CHILDREN.
Swallowing them may result in serious injury.
If swallowed, consult a physician immediately.
•
•
The CDA-9831/CDA-9830 uses female RCA-type jacks for
connection to other units (e.g. amplifier) having RCA
connectors. You may need an adaptor to connect other units. If
so, please contact your authorized ALPINE dealer for
assistance.
Be sure to connect the speaker (–) leads to the speaker (–)
terminal. Never connect left and right channel speaker cables
to each other or to the vehicle body.
DO NOT INSTALL IN LOCATIONS WHICH MIGHT HINDER
VEHICLE OPERATION, SUCH AS THE STEERING WHEEL
OR GEARSHIFT.
Doing so may obstruct forward vision or hamper movement etc.
and results in serious accident.
IMPORTANT
SERIAL NUMBER:
Please record the serial number of your unit in the space provided
below and keep it as a permanent record. The serial number plate is
located on the bottom of the unit.
INSTALLATION DATE:
INSTALLATION TECHNICIAN:
PLACE OF PURCHASE:
36-EN
Download from Www.Somanuals.com. All Manuals Search And Download.
Connect each input lead coming from an amplifier
or equalizer to the corresponding output lead
coming from the left rear of the CDA-9831/CDA-
9830. Connect all other leads of the CDA-9831/CDA-
9830 according to details described in the
CONNECTlONS section.
Installation
Metal plate
Detachable
Front panel
3
Caution
When you install this unit in your car, do not remove the
detachable front panel.
If the detachable front panel is removed during installation, you
might press too hard and warp the metal plate that holds it in
place.
Lock Pin
Caution
Do not block the unit’s fan or heat sink, thus preventing air
circulation. If blocked, heat will accumulate inside the unit and
may cause a fire.
Slide the CDA-9831/CDA-9830 into the dashboard.
When the unit is in place, make sure the locking
pins are fully seated in the down position.This can
be done by pressing firmly in on the unit while
pushing the locking pin down with a small
Air ventilation hole
screwdriver.This ensures that the unit is properly
locked and will not accidentally come out from the
dashboard. Install the detachable front panel.
(Rear of CDA-9831/CDA-9830)
Removal
1 Remove the detachable front panel.
1
Mounting Sleeve
(Included)
2 Use a small screwdriver (or similar tool) to push the
locking pins to the “up” position (see above drawing).
As each pin is unlocked, gently pull out on the unit to
make sure it does not re-lock before unlocking the
second pin.
Dashboard
3 Pull the unit out, keeping it unlocked as you do so.
<JAPANESE CAR>
this unit
Slide the mounting sleeve into the dashboard.
2
Face Plate
Screw
Hex Nut (M5)
2
*
Bolt Stud
Screws (M5 × 8)
(Included)
Metal
Mounting
Strap
this unit
1
*
Ground Lead
3
*
this unit
Chassis
Ground Lead
Reinforce the head unit with the metal mounting
strap (not supplied). Secure the ground lead of the
unit to a clean metal spot using a screw (*1) already
attached to the vehicle's chassis.
Mounting Bracket
•
Secure the ground lead of the unit to a clean metal spot using a
screw (*3) already attached to the vehicle's chassis.
•
For the screw marked “*2”, use an appropriate screw for the
chosen mounting location.
37-EN
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections
1
2
To amplifier (CDA-9831 only)
Antenna
Blue
POWER ANT
3
4
5
To power antenna
REMOTE
TURN-ON
Blue/White
To amplifier or equalizer
To vehicle phone
AUDIO
INTERRUPT IN
Pink/Black
Orange ILLUMINATION
6
To the instrument cluster illumination
lead (CDA-9831 only)
IGNITION
BATTERY
Red
7
8
Ignition Key
Yellow
!
Black
GND
9
Battery
Gray
#
$
Speakers
SPEAKER
RIGHT FRONT
Front right
Gray/Black
Violet/Black
%
&
SPEAKER
RIGHT REAR
/
.
,
<
Rear right
Violet
Green
(
)
"
SPEAKER
LEFT REAR
Ai-NET
Rear left
Front left
Green/Black
White/Black
~
+
NORM EQ/DIV
SPEAKER
LEFT FRONT
∗1
White
-
CD Changer
(Sold Separately)
Speakers
Front Left
;
Amplifier
Front Right
Rear Left
;
:
Amplifier
Rear Right
;
Amplifier
Subwoofers
* 1 The label is attached on the bottom of the unit.
38-EN
Download from Www.Somanuals.com. All Manuals Search And Download.
1
Amplifier Link Connector
#
$
%
&
(
)
~
+
,
Right Front (+) Speaker Output Lead (Gray)
Right Front (–) Speaker Output Lead (Gray/Black)
Right Rear (–) Speaker Output Lead (Violet/Black)
Right Rear (+) Speaker Output Lead (Violet)
Left Rear (+) Speaker Output Lead (Green)
Left Rear (–) Speaker Output Lead (Green/Black)
Left Front (–) Speaker Output Lead (White/Black)
Left Front (+) Speaker Output Lead (White)
Outputs Amplifier Link control signals. Connect this to a
separately sold Amplifier Link-compatible amplifier, using
the (also separately sold) Amplifier Link box KCE-510M.
2
3
Antenna Receptacle
Power Antenna Lead (Blue)
Connect this lead to the +B terminal of your power antenna,
if applicable.
This lead should be used only for controlling the vehicle's power
antenna. Do not use this lead to turn on an amplifier, or a signal
processor, etc.
Ai-NET Connector
Connect this to the output or input connector of another
device (CD Changer, Equalizer, etc.) equipped with Ai-NET.
4
Remote Turn-On Lead (Blue/White)
Connect this lead to the remote turn-on lead of your
amplifier or signal processor.
You can input TV/video sound by connecting an optional Ai-
NET/RCA Interface cable (KCA-121B) to this component.
5
6
Audio Interrupt In Lead (Pink/Black)
-
.
Ai-NET Cable (Included with CD Changer)
Illumination Lead (Orange) (CDA-9831 only)
This lead may be connected to the vehicle's
instrument cluster illumination lead. This will allow
the backlighting of the CDA-9831 to dim whenever
the vehicle's lights are turned on.
Front Output RCA Connectors
RED is right and WHITE is left.
/
:
Rear Output RCA Connectors
RED is right and WHITE is left.
Subwoofer RCA Connectors
RED is right and WHITE is left.
7
Switched Power Lead (Ignition) (Red)
Connect this lead to an open terminal on the vehicle's fuse
box or another unused power source which provides (+)12V
only when the ignition is turned on or in the accessory
position.
;
<
RCA Extension Cable (sold separately)
System Switch
When connecting a processor or divider using Ai-NET, place
this switch in the EQ/DIV position. When no device is
connected, leave the switch in the NORM position.
8
9
Battery Lead (Yellow)
Connect this lead to the positive (+) post of the vehicle's
battery.
Be sure to turn the power off to the unit before changing the
switch position.
Ground Lead (Black)
Connect this lead to a good chassis ground on the vehicle.
Make sure the connection is made to bare metal and is
securely fastened using the sheet metal screw provided.
!
"
Choke Coil with Fuse Holder
(10A)
Power Supply Connector
To prevent noise/interference in the audio system.
• Locate the unit and route the leads at least 10 cm away from the car harness.
• Keep the battery power leads as far away from other leads as possible.
• Connect the ground lead securely to a bare metal spot (remove any paint, dirt or grease if necessary) of the car chassis.
• If you add an optional noise suppressor, connect it as far away from the unit as possible. Your Alpine dealer carries various noise
suppressors, contact them for further information.
• Your Alpine dealer knows best about noise prevention measures so consult your dealer for further information.
39-EN
Download from Www.Somanuals.com. All Manuals Search And Download.
LIMITED WARRANTY
ALPINE ELECTRONICS OF AMERICA, INC. AND ALPINE OF CANADA INC. ("Alpine"), are dedicated to quality
craftsmanship and are pleased to offer this Warranty. We suggest that you read it thoroughly. Should you have any
questions, please contact your Dealer or Alpine at one of the telephone numbers listed below.
2 You should provide a detailed description of the
[PRODUCTS COVERED:
problem(s) for which service is required.
3 You must supply proof of your purchase of the product.
4 You must package the product securely to avoid
damage during shipment.
This Warranty covers Car Audio/Visual Products and
Related Accessories ("the product"). Products purchased in
the Canada are covered only in the Canada. Products
purchased in the U.S.A. are covered only in the U.S.A.
[HOW WE LIMIT IMPLIED WARRANTIES:
ANY IMPLIED WARRANTIES INCLUDING FITNESS FOR
USE AND MERCHANTABILITY ARE LIMITED IN
DURATION TO THE PERIOD OF THE EXPRESS
WARRANTY SET FORTH ABOVE AND NO PERSON IS
AUTHORIZED TO ASSUME FOR ALPINE ANY OTHER
LIABILITY IN CONNECTION WITH THE SALE OF THE
PRODUCT.
[LENGTH OF WARRANTY:
This Warranty is in effect for one year from the date of the
first consumer purchase.
[LIFETIME TAPE HEAD WARRANTY:
All Alpine Car Audio analog tape heads excluding Video
tape heads are warranted for life against manufacturing
defects causing failure.
[WHO IS COVERED:
[HOW WE EXCLUDE CERTAIN DAMAGES:
ALPINE EXPRESSLY DISCLAIMS LIABILITY FOR
INCIDENTAL AND CONSEQUENTIAL DAMAGES
CAUSED BY THE PRODUCT. THE TERM "INCIDENTAL
DAMAGES" REFERS TO EXPENSES OF
This Warranty only covers the original purchaser of the
product, who must reside in the United States, Puerto Rico
or Canada.
[WHAT IS COVERED:
This Warranty covers defects in materials or workmanship
(parts and labor) in the product.
TRANSPORTING THE PRODUCT TO THE ALPINE
SERVICE CENTER, LOSS OF THE ORIGINAL
PURCHASER'S TIME, LOSS OF THE USE OF THE
PRODUCT, BUS FARES, CAR RENTALS OR OTHERS
COSTS RELATING TO THE CARE AND CUSTODY OF
THE PRODUCT. THE TERM "CONSEQUENTIAL
DAMAGES" REFERS TO THE COST OF REPAIRING OR
REPLACING OTHER PROPERTY WHICH IS DAMAGED
WHEN THIS PRODUCT DOES NOT WORK PROPERLY.
THE REMEDIES PROVIDED UNDER THIS WARRANTY
ARE EXCLUSIVE AND IN LIEU OF ALL OTHERS.
[WHAT IS NOT COVERED:
This Warranty does not cover the following:
1 Damage occurring during shipment of the product to
Alpine for repair (claims must be presented to the
carrier).
2 Damage caused by accident, abuse, negligence,
misuse, improper connections, improper operation or
failure to follow instructions contained in the Owner's
manual.
3 Damage caused by act of God, including without
limitation, earthquake, fire, flood, storms or other acts of
nature.
4 Any cost or expense related to the removal or
reinstallation of the product.
5 Service performed by an unauthorized person, company
or association.
6 Any product which has the serial number defaced,
altered or removed.
7 Any product which has been adjusted, altered or
modified without Alpine's consent.
8 Any product not distributed by Alpine within the United
States, Puerto Rico or Canada.
9 Any product not purchased from an Authorized Alpine
Dealer.
[HOW STATE/PROVINCIAL LAW RELATES TO THE
WARRANTY:
This Warranty gives you specific legal rights, and you may
also have other rights which vary form state to state and
province to province. In addition, some states/provinces do
not allow limitations on how long an implied warranty lasts,
and some do not allow the exclusion or limitation of
incidental or consequential damages. Accordingly,
limitations as to these matters contained herein may not
apply to you.
[IN CANADA ONLY:
This Warranty is not valid unless your Alpine car audio
product has been installed in your vehicle by an Authorized
Installation Center, and this warranty stamped upon
installation by the installation center.
! Any product that has been determined to contain an
excessive amount of dust or dirt and any product that
contains other contaminants including liquid or foreign
objects.
[HOW TO CONTACT CUSTOMER SERVICE:
Should the product require service, please call the following
number for your nearest Authorized Alpine Service Center.
[HOW TO OBTAIN WARRANTY SERVICE:
1 You are responsible for delivery of the product to an
Authorized Alpine Service Center or Alpine for repair
and for payment of any initial shipping charges. Alpine
will, at its option, repair or replace the product with a
new or reconditioned product without charge. If the
repairs are covered by the warranty, and if the product
was shipped to an Authorized Alpine Service Center or
Alpine, Alpine will pay the return shipping charges.
U.S.A.
CANADA
1-800-ALPINE-1 (1-800-257-4631)
1-800-ALPINE-1 (1-800-257-4631)
Alpine Electronics of America, Inc., 19145 Gramercy Place, Torrance, California 90501, U.S.A.
Alpine Electronics of Canada, Inc., Suite 203, 7300 Warden Ave. Markham, Ontario, L3R 9Z6, Canada
Download from Www.Somanuals.com. All Manuals Search And Download.
|