Patch Release Note
Patch SB244-03
For SwitchBlade 4000 Series Switches and
AT-9800 Series Switches
Introduction
This patch release note lists the issues addressed and enhancements made in
patch SB244-03 for Software Release 2.4.4 on existing models of SwitchBlade
4000 Series Switches and AT-9800 Series Switches. Patch file details are listed in
Table 1: Patch file details for Patch SB244-03.
sb-244.rez
Base Software Release File
Patch Release Date
26-Nov-2002
sb244-03.paz
250571 bytes
Compressed Patch File Name
Compressed Patch File Size
This release note should be read in conjunction with the following documents:
■
SwitchBlade Documentation Set for Software Release 2.4.3 (Document
Number C613-03042-00 Rev E) and Release Note for Software Release 2.4.4
for SwitchBlade 4000 Switches and AT-9800 Series Switches (Document
Number C613-10342-00 Rev A) available on the Documentation and Tools
CD-ROM packaged with your switch, or from www.alliedtelesyn.co.nz/
■
AT9800 Series Switches Documentation Set for Software Release 2.4.3
(Document Number C613-03044-00 Rev B) and Release Note for Software
Release 2.4.4 for SwitchBlade 4000 Switches and AT-9800 Series Switches
(Document Number C613-10342-00 Rev A) available on the
Documentation and Tools CD-ROM packaged with your switch, or from
WARNING: Using a patch for a different model or software release may cause
unpredictable results, including disruption to the network. Information in this
release note is subject to change without notice and does not represent a
commitment on the part of Allied Telesyn International. While every effort has
been made to ensure that the information contained within this document and
the features and changes described are accurate, Allied Telesyn International
can not accept any type of liability for errors in, or omissions arising from the
use of this information.
Simply connecting the world
Download from Www.Somanuals.com. All Manuals Search And Download.
Patch SB244-03 For SwitchBlade 4000 Series Switches and AT-9800 Series Switches
3
PCR: 02492
Module: SWI
Network affecting: No
288MB RDRAM was initialised incorrectly, resulting in unpredictable
behaviour. This issue has been resolved.
PCR: 02493
Module: DHCP
Network affecting: No
Inuse DHCP entries (that are displayed in the SHOW DHCP CLIENT
command) will now expire and be reclaimed.
PCR: 02494
Module: IPv6
Network affecting: No
It was possible to add the same IPv6 prefix to different IPv6 interfaces. This
issue has been resolved.
PCR: 02497
Module: PPP
Network affecting: No
The wrong error message was displayed if PPP compression over L2TP was
attempted. The correct message is now generated, stating that the CREATE
PPP command is invalid.
PCR: 02499
Module: IPG
Network affecting: No
Some parameters in the SET IP IGMP command had incorrect ranges. This
issue has been resolved. The correct ranges are:
SET IP IGMP [LMQI=1..255] [LMQC=1..5]
[QUERYINTERVAL=1..65535] [QUERYRESPONSEINTERVAL=1..255]
[ROBUSTNESS=1..5] [TIMEOUT=1..65535]
PCR: 02502
Module: Ping, IPv6
Network affecting: No
If multiple IPv6 interfaces shared the same link-local address, pings to the
link-local address sometimes failed. This issue has been resolved.
PCR: 02503
Module: NVS
Network affecting: No
Loading files to NVS caused a fatal error. This issue has been resolved.
PCR: 02504
Module: SWI
Network affecting: No
A warning was not given if the egress limit for a port was not set to a
multiple of 64. This issue has been resolved.
PCR: 02507
Module: SWI
Network affecting: No
ARP entries on the SwitchBlade 4000 Series Switch controller card are now
updated correctly if a device changes to a different line card.
PCR: 02509
Module: DVMRP
Network affecting: No
The source net mask has been removed from DVMRP prune, graft and
graft-ack messages.
PCR: 02511
Module: Ping
Network affecting: No
Executing the PING command sometimes caused a memory leak. This issue
has been resolved.
PCR: 02516
Module: IPG
Network affecting: No
Untagged IGMP packets were erroneously sent out of tagged ports. This
issue has been resolved.
Patch SB244-03 for Software Release 2.4.4
C613-10349-00 REV C
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Patch Release Note
Features in SB244-02
Patch file details are listed in Table 2:
Table 2: Patch file details for Patch SB244-02.
sb-244.rez
Base Software Release File
Patch Release Date
1-Nov-2002
sb244-02.paz
57728 bytes
Compressed Patch File Name
Compressed Patch File Size
Patch SB244-02 includes all issues resolved and enhancements released in
previous patches for Software Release 2.4.4, and the following enhancements:
PCR: 02406
Module: IPV6
Network affecting: No
Some parameters in MLD specific query messages were not working
correctly. This issue has been resolved.
PCR: 02426
Module: IPV6
Network affecting: No
The ENABLE IPV6 MTUDISCOVERY and SET IPV6 MTU INTERFACE
commands were not displayed in the SHOW CONFIGURATION
DYNAMIC command. This issue has been resolved.
PCR: 02427
Module: DHCP
Network affecting: No
DHCP entry reclaim checks are now delayed by 10 seconds if the entry is
unroutable because the interface is not up.
PCR: 02428
Module: IPV6
Network affecting: No
Link-local address behaviour was incorrect. Also, the PUBLISH parameter
was not updated by the SET IPV6 INTERFACE command, or displayed in
the SHOW IPV6 INTERFACE command. These issues have been resolved.
PCR: 02450
Module: IPV6
Network affecting: No
Large local packets were not being fragmented. Also, the More Fragment
flag in the IPv6 fragment header was not being set correctly. These issues
have been resolved.
PCR: 02452
Module: IPV6
Network affecting: No
Received Router Advertisements (RAs) were discarded when the interface
was enabled to send RAs. This issue has been resolved.
PCR: 02458
Module: SWI, GUI
Network affecting: No
The status page in the GUI was not displaying correctly. This issue has been
resolved.
PCR: 02459
Module: CORE
Network affecting: No
The SLVPASSWORD string in the ENABLE SYSTEM SYSR SLVFEATURE
and ENABLE SYSTEM SYSR SLVRELEASE commands was not copying
correctly. This issue has been resolved.
Patch SB244-03 for Software Release 2.4.4
C613-10349-00 REV C
Download from Www.Somanuals.com. All Manuals Search And Download.
Patch SB244-03 For SwitchBlade 4000 Series Switches and AT-9800 Series Switches
5
PCR: 02460
Module: SWI
Network affecting: No
Sometimes a port reported an interface as being down, but the port counters
kept incrementing. This issue has been resolved.
PCR: 02461
Module: SWI
Network affecting: No
The CREATE TRIGGER MODULE=SWITCH command now recognises
ports in x.y notation when specifying the PORT parameter.
PCR: 02462
Module: SWI
Network affecting: No
A fatal error occurred on SwitchBlade 4000 Series Switches when booting
from a script that added ports to a trunk group that was hot swapped out.
This issue has been resolved.
PCR: 02463
Module: DVMRP, IPG
Network affecting: No
Support for multi-homed interfaces has been added.
PCR: 02467
Module: CORE
Network affecting: No
The board descriptions have changed for some instances of AT-9800 Series
Switches.
PCR: 02468
Module: SWI
Network affecting: No
When a Telnet session was closed, SWITCH debug was not disabled if it had
been enabled for the Telnet session. This issue has been resolved.
PCR: 02469
Module: TM
Network affecting: No
After an ASYN port test, the port is now reset to its pre-test state if the test
was started by a user connected to the same ASYN port.
PCR: 02470
Module: SWI
Network affecting: No
The Built-in Self Test failed on SwitchBlade chassis. This issue has been
resolved.
PCR: 02476
Module: VRRP, CORE
Network affecting: No
The configuration was not restored correctly after a line card was hot
swapped out. This issue has been resolved.
PCR: 02478
Module: SCRIPT
Network affecting: No
A string compare error was occurring in the conditional statement of the
script. This issue has been resolved.
Patch SB244-03 for Software Release 2.4.4
C613-10349-00 REV C
Download from Www.Somanuals.com. All Manuals Search And Download.
6
Patch Release Note
Features in SB244-01
Table 3: Patch file details for Patch SB244-01.
sb-244.rez
Base Software Release File
Patch Release Date
23-Oct-2002
sb244-01.paz
84666 bytes
Compressed Patch File Name
Compressed Patch File Size
Patch SB244-01 includes the following enhancements:
PCR: 01285 Module: OSPF Network affecting: No
When an interface went down (or was disabled) on an AS border router, the
external routes were not removed from the routing domain. Such routes are
now removed by premature aging.
PCR: 02353
Module: SWI
Network affecting: No
The learning unit was locking under heavy load. This could result in pings
to a network device failing, and over an hour all dynamic MAC addresses
could be lost. Sometimes a large number of pause frames were generated by
the system. This issue has been resolved.
PCR: 02359
Module: IPG
Network affecting: No
When an IP Multihomed interface was used as an OSPF interface,
neighbour relationships were only established if the IP interface for OSPF
was added first in the configuration. Now, OSPF establishes neighbour
relationships regardless of the IP Multihomed interface configuration order.
PCR: 02361
Module: SWI
Network affecting: No
The SwitchBlade mirror port field on the second instance of a switch chip
was displaying as though it was the first instance. This issue has been
resolved.
PCR: 02394
Module: IPG, SWI, DVMRP
Network affecting: No
The following issues have been resolved:
•
•
•
IP route updating was not working correctly
IGMP snooping behaviour was incorrect
The SHOW DVMRP FORWARDING command displayed incorrect
port numbers.
PCR: 02396
Module: DHCP
Network affecting: No
DHCP RENEW request messages are now unicast (as defined in the RFC),
not broadcast.
PCR: 02397
Module: DVMRP
Network affecting: No
After a prune lifetime had expired, the interface was not joined back to the
DVMRP multicast delivery tree. This issue has been resolved.
Patch SB244-03 for Software Release 2.4.4
C613-10349-00 REV C
Download from Www.Somanuals.com. All Manuals Search And Download.
Patch SB244-03 For SwitchBlade 4000 Series Switches and AT-9800 Series Switches
7
PCR: 02398
Module: IPV6
Network affecting: No
The following issues have been resolved:
•
•
•
It was possible to assign the same network on different IPV6 interfaces
The loopback address was being added to other interfaces
The tunnel configuration was not showing correctly in IPV6
configuration commands
•
RIPv6 now sets the metric of routes for interfaces that are DOWN to 16,
and immediately sends responses when the link status of VLAN
interfaces changes.
PCR: 02401
Module: IPV6
Network affecting: No
Neighbour discovery and PIM6 caused a fatal error when IPv6 was not
enabled, or when the IPv6 feature license was not present. This issue has
been resolved.
PCR: 02406
Module: IPV6
Network affecting: No
A Router-Alert option has been added. Also, the SHOW IPV6 MLD
INTERFACE command now works correctly.
PCR: 02407
Module: IPG
Network affecting: No
ICMP was sending too many messages back as responses to fragmented
packets. This issue has been resolved.
PCR: 02409
Module: IPG
Network affecting: No
A warning now appears when the DELETE IP INTERFACE command is
executed before the DELETE DVMRP INTERFACE command.
PCR: 02410
Module: VRRP
Network affecting: No
VRRP pre-empt mode was not working with advertisement updates of 1
second or more because this did not allow for interface start time on startup.
Now a check is made to verify that interfaces are UP before timers are
started.
PCR: 02413
Module: IPG, IPX2
Network affecting: No
Static IP ARP entries could not be added to hardware at boot time. Also, an
IPX circuit could not be deleted from hardware. These issues have been
resolved.
PCR: 02416
Module: DVMRP, IPG
Network affecting: No
Multicasting forwarding was not working correctly. This issue has been
resolved.
PCR: 02417
Module: VLAN, IPG
Network affecting: No
The IGMP port list was not updating correctly when a port went down. This
issue has been resolved.
PCR: 02418
Module: IPV6
Network affecting: No
ICMPv6 was returning an error for non-zero fragment offsets. This issue has
been resolved.
Patch SB244-03 for Software Release 2.4.4
C613-10349-00 REV C
Download from Www.Somanuals.com. All Manuals Search And Download.
8
Patch Release Note
PCR: 02415
Module: IPG
Network affecting: No
Packets with a RIP source address and next hop address that are not on the
same subnet as the interface will now be processed. If the received next hop
is not on the same subnet, it is treated as 0.0.0.0.
PCR: 02420
Module: SWI
Network affecting: No
On GBICs, the link was forced up when the transmit fibre was removed.
Once up, the link could not be taken down again by removing the transmit
fibre. This issue has been resolved.
PCR: 02423
Module: SWI
Network affecting: No
IGMP messages sometimes caused a fatal error. This issue has been
resolved.
PCR: 02425
Module: IPG
Network affecting: No
Multicast downstream groups are now added and deleted correctly.
Errata
AT-9800 Series Switches do not have Ethernet interfaces (for example, eth0).
Previously released documentation incorrectly states that these interface types
are valid. AT-9800 switch ports are Ethernet ports, and these are referenced in
commands with the PORT parameter.
IPSec and ISAKMP are not available on the 2.4.4 release for SwitchBlade 4000
Series Switches and AT-9800 Series Switches.
Availability
Patches can be downloaded from the Software Updates area of the Allied
licence or password is not required to use a patch.
Patch SB244-03 for Software Release 2.4.4
C613-10349-00 REV C
Download from Www.Somanuals.com. All Manuals Search And Download.
|