Washer-Extractors
Pocket Hardmount
Variable-Speed
V-Series Microcomputer
Models UW100VV and UW125VV
For Designs 1-4
NOTA: El manual en
españolaparecedespués
del manual en inglés.
Keep These Instructions for Future Reference.
(If this machine changes ownership, this manual must accompany machine.)
Part No. F232123R3
March 2006
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety....................................................................................................
Operator Safety.....................................................................................
3
Table of
Contents
Operation.............................................................................................
9
Theory of Operation ............................................................................. 12
Keypad ............................................................................................. 13
Opening Door ....................................................................................... 15
Loading................................................................................................. 15
Cycle Selection ..................................................................................... 15
Cycle Execution.................................................................................... 16
Fill.................................................................................................... 16
Wash ................................................................................................ 16
Drain ................................................................................................ 17
Spin .................................................................................................. 17
Stop Routine ......................................................................................... 17
Balance Detection................................................................................. 18
Programming ...................................................................................... 19
Setup Mode........................................................................................... 19
Cycle Count .......................................................................................... 21
© Copyright 2006, Alliance Laundry Systems LLC
All rights reserved. No part of the contents of this book may be reproduced or transmitted in any form or by any
means without the expressed written consent of the publisher.
F232123
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Test Cycle............................................................................................. 25
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F232123
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety
Anyone operating or servicing this machine must
follow the safety rules in this manual. Particular
WARNING
This machine must be installed, adjusted,
and serviced by qualified electrical
attention must be paid to the CAUTION, WARNING,
and DANGER blocks which appear throughout the
manual.
maintenance personnel familiar with the
construction and operation of this type of
machinery. They must also be familiar
with the potential hazards involved.
Failure to observe this warning may result
in personal injury and/or equipment
CAUTION
Be careful around the open door,
particularly when loading from a level
below the door. Impact with door edges
can cause personal injury.
damage, and may void the warranty.
SW004
SW025
CAUTION
Ensure that the machine is installed on a
level floor of sufficient strength and that
the recommended clearances for
inspection and maintenance are provided.
Never allow the inspection and
maintenance space to be blocked.
WARNING
Dangerous voltages are present in the
electrical control box(es) and at the motor
terminals. Only qualified personnel
familiar with electrical test procedures,
test equipment, and safety precautions
should attempt adjustments and
SW020
troubleshooting. Disconnect power from
the machine before removing the control
box cover, and before attempting any
WARNING
service procedures.
SW005
Never touch internal or external steam
pipes, connections, or components.
These surfaces can be extremely hot and
will cause severe burns. The steam must
be turned off and the pipe, connections,
and components allowed to cool before
The following warnings are general examples that
apply to this machine. Warnings specific to a particular
operation will appear in the manual with the
discussion of that operation.
the pipe can be touched.
DANGER
SW014
Death or serious injury can result if
children become trapped in the machine.
Do not allow children to play on or around
this machine. Do not leave children
unattended while the machine door is
open.
SW001
F232123
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Download from Www.Somanuals.com. All Manuals Search And Download.
3
Safety
Key to Symbols
This warning symbol indicates the presence of possibly
dangerous chemicals. Proper precautions should be
taken when handling corrosive or caustic materials.
The lightning flash and arrowhead within the triangle
is a warning sign indicating the presence of dangerous
voltage.
This warning symbol indicates the presence of hot
surfaces that could cause serious burns. Stainless steel
and steam lines can become extremely hot and should
not be touched.
The exclamation point within the triangle is a warning
sign indicating important instructions concerning the
machine and possibly dangerous conditions.
This warning symbol indicates the presence of
possibly dangerous pinch-points. Moving mechanical
parts can crush and/or sever body parts.
This warning symbol indicates the presence of
potentially dangerous drive mechanisms within the
machine. Guards should always be in place when the
machine is in operation.
F232123
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Safety
Safety Decals
Safety decals appear at crucial locations on the
machine. Failure to maintain legible safety decals could
result in injury to the operator or service technician.
To provide personal safety and keep the machine in
proper working order, follow all maintenance and
safety procedures presented in this manual. If questions
regarding safety arise, contact the factory immediately.
Use factory-authorized spare parts to avoid safety
hazards.
F232123
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Download from Www.Somanuals.com. All Manuals Search And Download.
5
Safety
Operator Safety
Safe Operating Environment
Safe operation requires an appropriate operating
environment for both the operator and the machine. If
questions regarding safety arise, contact the factory
immediately.
WARNING
NEVER insert hands or objects into
basket until it has completely stopped.
Doing so could result in serious injury.
Environmental Conditions
SW012
●
Ambient Temperature. Water in the machine will
To ensure the safety of machine operators, the following
maintenance checks must be performed daily:
freeze at temperatures of 32°F (0°C) or below.
Temperatures above 120°F (50°C) will result in
more frequent motor overheating and, in some
cases, malfunction or premature damage to solid
state devices that are used in some models.
Special cooling devices may be necessary.
1. Prior to operating the machine, verify that all
warning signs are present and legible. Missing or
illegible signs must be replaced immediately.
Make certain that spares are available.
2. Check door interlock before starting operation of
the machine:
Water pressure switches are affected by increases
and decreases in temperature. Every 25°F
(10°C) change in temperature will have a 1%
effect on the water level.
a. Attempt to start the machine with the door
open. The machine should not start with the
door open.
●
Humidity. Relative humidity above 90% may
cause the machine’s electronics or motors to
malfunction or may trip the ground fault
interrupter. Corrosion problems may occur on
some metal components in the machine.
b. Close the door without locking it and attempt
to start the machine. The machine should not
start with the door unlocked.
c. Close and lock the door and start a cycle.
Attempt to open the door while the cycle is in
progress. The door should not open.
If the relative humidity is below 30%, belts and
rubber hoses may eventually develop dry rot.
This condition can result in hose leaks, which
may cause safety hazards external to the machine
in conjunction with adjacent electrical
equipment.
If the door lock and interlock are not functioning
properly, call a service technician.
3. Do not attempt to operate the machine if any of
the following conditions are present:
●
Ventilation. The need for make-up air openings
for such laundry room accessories as dryers,
ironers, or water heaters must be evaluated
periodically. Louvers, screens, or other
separating devices may reduce the available air
opening significantly.
a. The door does not remain securely locked
during the entire cycle.
b. Excessively high water level is evident.
c. Machine is not connected to a properly
grounded circuit.
●
●
Radio Frequency Emissions. A filter is available
for machines in installations where floor space is
shared with equipment sensitive to radio
frequency emissions.
Do not bypass any safety devices in the machine.
WARNING
Never operate the machine with a
Elevation. If the machine is to be operated at
elevations of over 3280 feet (1000 meters) above
sea level, pay special attention to water levels and
electronic settings (particularly temperature) or
desired results may not be achieved.
bypassed or disconnected balance
system. Operating the machine with
severe out-of-balance loads could result
in personal injury and serious equipment
●
Chemicals. Keep stainless steel surfaces
freeofchemical residues.
damage.
SW039
F232123
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety
Input and Output Services
DANGER
●
Water Pressure. Best performance will be
realized if water is provided at a pressure of
30 – 85 psi (2.0 – 5.7 bar). Although the machine
will function properly at lower pressure,
increased fill times will occur. Water pressure
higher than 100 psi (6.7 bar) may result in
damage to machine plumbing. Component
failure(s) and personal injury could result.
Do not place volatile or flammable fluids
in any machine. Do not clean the machine
with volatile or flammable fluids such as
acetone, lacquer thinners, enamel
reducers, carbon tetrachloride, gasoline,
benzene, naptha, etc. Doing so could
result in serious personal injury and/or
damage to the machine.
●
Steam Heat (Optional) Pressure. Best
performance will be realized if steam is provided
at a pressure of 30 – 80 psi (2.0 – 5.4 bar). Steam
pressure higher than 125 psi (8.5 bar) may result
in damage to steam components and may cause
personal injury.
SW002
●
Water Damage. Do not spray the machine with
water. Short circuiting and serious damage may
result.
Machine Location
For machines equipped with optional steam heat,
install piping in accordance with approved
commercial steam practices. Failure to install the
supplied steam filter may void the warranty.
●
Foundation. The concrete floor must be of
sufficient strength and thickness to handle the
floor loads generated by the high extract speeds
of the machine.
●
●
Compressed Air. For machines requiring
compressed air service, best performance will be
realized if air is provided at a pressure of
80 – 100 psi (5.4 – 6.7 bar).
●
Service/Maintenance Space. Provide sufficient
space to allow comfortable performance of
service procedures and routine preventive
maintenance.
Drainage System. Provide drain lines or troughs
large enough to accommodate the total number of
gallons that could be dumped if all machines on
the site drained at the same time from the highest
attainable level. If troughs are used, they should
be covered to support light foot traffic.
This is especially important in connection with
machines equipped with an AC inverter drive.
Consult installation instructions for specific details.
CAUTION
Replace all panels that are removed to
perform service and maintenance
procedures. Do not operate the machine
with missing guards or with broken or
missing parts. Do not bypass any safety
●
Power. For personal safety and for proper
operation, the machine must be grounded in
accordance with state and local codes. The
ground connection must be to a proven earth
ground, not to conduit or water pipes. Do not use
fuses in place of the circuit breaker. An easy-
access cutoff switch should also be provided.
devices.
SW019
WARNING
Ensure that a ground wire from a proven
earth ground is connected to the ground
lug near the input power block on this
machine. Without proper grounding,
personal injury from electric shock could
occur and machine malfunctions may be
evident.
SW008
Always disconnect power and water supplies before
a service technician performs any service procedure.
Where applicable, steam and/or compressed air
supplies should also be disconnected before service
is performed.
F232123
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Download from Www.Somanuals.com. All Manuals Search And Download.
7
Safety
AC Inverter Drive
Misuse
Machines equipped with the AC inverter drive require
special attention with regard to the operating
environment.
Never use this machine for any purpose other than
washing fabric with water.
●
●
Never wash petroleum-soaked rags in the
machine. This could result in an explosion.
●
An especially dusty or linty environment will
require more frequent cleaning of the AC inverter
drive cooling fan filter and of the AC inverter
drive itself.
Never wash machine parts or automotive parts in
the machine. This could result in serious damage
to the basket.
●
Power line fluctuations from sources such as
uninterruptible power supplies (UPS) can
adversely affect machines equipped with the AC
inverter drive. Proper suppression devices should
be utilized on the incoming power to the machine
to avoid problems.
●
Never allow children to play on or around this
machine. Death or serious injury can result if
children become trapped in the machine. Do not
leave children unattended while the machine door
is open. These cautions apply to animals as well.
●
A clean power supply free from voltage spikes
and surges is absolutely essential for machines
equipped with the AC inverter drive. Nonlinear
inconsistencies (peaks and valleys) in the power
supply can cause the AC inverter drive to
generate nuisance errors.
If voltage is above 240 Volt for 200 Volt
installations or above 480 Volt for 400 Volt
installations, a buckboost transformer is required.
●
Sufficient space to perform service procedures
and routine preventive maintenance is especially
important for machines equipped with the AC
inverter drive.
F232123
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Model Identification
Customer Service
Information in this manual is applicable to these
models:
UW100VV*
If literature or replacement parts are required, contact
the source from whom the machine was purchased
or contact Alliance Laundry Systems LLC at
(920) 748-3950 for the name and address of the
nearest authorized parts distributor.
UW125VV*
For technical assistance call:
*This manual applies to models with U1, U2, U3 or
th
th
U4 in the 9 and 10 positions in the model number
(e.g., UW100VVXU40001). Refer to Model Number
Familiarization Guide.
(920) 748-3121
Ripon, Wisconsin
This manual is designed as a guide to operating
and programming the 100 pound and 125 pound
capacity pocket hardmount washer-extractor equipped
with the V-computer and AC inverter drive.
A record of each machine is on file with the
manufacturer. Always provide the machine’s serial
number and model number when ordering parts or
when seeking technical assistance.
The manuals, installation instructions, and wiring
diagrams which accompany the machine have been
included with the machine at no charge. Additional
copies are available at a nominal charge.
NOTE: Read this manual thoroughly before
attempting to operate the machine or program the
microcomputer.
NOTE: Do not use this manual in conjunction with
earlier model computer-controlled machines. Do
not use technical literature intended for earlier
models when operating this machine.
NOTE: All information, illustrations, and
specifications contained in this manual are based
on the latest product information available at the
time of printing. We reserve the right to make
changes at any time without notice.
F232123
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Download from Www.Somanuals.com. All Manuals Search And Download.
9
Operation
Model Number Familiarization Guide
Sample Model Number: UW100VVXU40001
Model Number Prefix
UW
100
V
Washer-Extractor Capacity (pounds dry weight of laundry)
Type of Electrical Control
Washer-Extractor Speed Capabilities
Electrical Characteristics
V
X
Design Series
4
Option Identification (varies from machine to machine)
0001
UW100VVXU40001
00000000000
14
200 – 240
20
50 – 60
2/3
1/3
60
N/A
27
813
0.0
N/A
Drawings:
ETL Listed
Conforms To ANSI/UL Std. 1206, 3rd Ed
Certified To CAN/CSA Std. C22.2 No.53-1968
EXAMPLE OF NAMEPLATE
PHM627N
Figure 1
F232123
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
and identifies the major operational features of the
Machine Familiarization Guide
machine.
The machine familiarization guide in Figure 2
provides front and rear views of the washer-extractor
1
14
2
3
13
Stop
Start
Down
Up
4
WARNING
MACHINE MAY BE HOT
AND CAUSE BURNS
ATTEMPT NO ENTRY UNTIL
BASKET HAS STOPPED
SERIOUS INJURY MAY RESU
LT
12
5
11
6
10
7
8
9
P005I
1
2
3
4
5
6
7
Emergency Stop Button
Supply Valve Box
Supply Dispenser
Door Handle
Door Box
Door Latch Extension Arm
Door Latch
8
9
Side Panel
Front Panel
Rub Rail
Shell Front
Door Hinge
Door
10
11
12
13
14
Control Module
Figure 2
F232123
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
The machine uses an AC inverter drive control which
provides five motor speeds using a single motor. The
solid state output board converts motor logic from the
V-computer to the correct signals for the AC inverter
drive.
Theory of Operation
The design of the machine emphasizes performance
reliability and long service life. The cylinder, shell,
and main body panels are fabricated of stainless steel.
The cylinder is driven by a V-drive system supported
via the shaft by two flange-mounted spherical roller
bearings bolted to the A-frame.
The operator can select from among 30 cycles. A
special permanent test cycle can be selected to verify
proper operation of the machine.
The machine uses one motor to drive the cylinder via a
V-belt drive in all speeds.
Liquid supplies can be injected directly into the cups
by a customer-supplied external chemical supply
system. Five hose strain reliefs on top of the supply
dispenser facilitate connection to an external supply
system. A terminal strip inside a compartment
attached to the left side of the control module, viewed
from the rear of the washer-extractor, provides
connection points for external supply signals.
A door-lock system prevents opening of the stainless
steel door when water is in the machine. It also
prevents operation of the machine when the door is
open.
Electrically operated drain valves are used to retain the
water and wash solution in the machine during the
wash and fill steps. The drain valve closes when power
is applied and opens when power is removed, allowing
the machine to drain in the event of a power failure.
V-Computer
The V-computer control is a programmable solid-state
control capable of storing and running up to 30 cycles.
A detailed description of these cycles can be found in
the Programming section of this manual.
The cylinder is designed with lifters or ribs that lift the
garments from the wash solution when the cylinder
rotates at slow speed and allow the garments to tumble
back into the solution. The cylinder is perforated,
allowing the water to pass through and drain from
within during the wash process and extract.
If this machine’s computer has been equipped with
special preprogrammed cycles, a separate insert listing
these cycles has been included in the resealable plastic
bag which contained this manual.
Electrical controls for the machine are housed in a
separate enclosure located underneath the top cover of
the machine.
NOTE: Never turn the power off while the
computer mode switch is in the Program position.
Such action will disorder portions of the
programmed data, necessitating reprogramming of
some or all of the existing cycles. Always return the
mode switch to Run position before turning the
power off.
There are two possible load balance systems, the “AC
Inverter Drive Balance Detection” and the “Overtravel
Balance Detection.”
The balance detection system using the overtravel
limit switch does not rely on the AC inverter drive and
does not attempt to balance the load in a drain step. As
the cylinder is spinning at the programmed speed, if
the wash load becomes unbalanced, the overtravel
limit switch is “tripped” causing the cylinder to slow
to a stop until the end of the spin step.
The balance detection system using the AC inverter
drive uses special balance detection software in
conjunction with the V-computer to prevent out-of-
balance conditions. When the AC drive detects an
unbalanced load at the end of a drain step, the
computer will make up to seven attempts to balance
the load. After the seventh try the machine spins at a
safe speed. As a fail-safe measure, an overtravel limit
switch is installed.
F232123
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Download from Www.Somanuals.com. All Manuals Search And Download.
12
Operation
Keypad
Conditions Monitored by the Computer
Operation of the V-computer control is performed with
a four-key touch keypad and LED display located on
●
Door – The computer continuously monitors
the open/locked status of the door. If it detects
that the door is open during a wash cycle, it
immediately aborts the cycle and executes the
stop routine.
2
3
1
4
●
Power – If power is interrupted long enough
for the computer to go off, after the power is
restored, the display flashes “Hold” briefly to
indicate the interruption. The door unlock will be
disabled to keep the door from being opened
while the basket is still turning.
●
Balance – If the AC inverter balance detection
system is utilized, the computer monitors the
balance signal provided by the AC drive during
drain steps. The computer will attempt to
distribute the load seven times. The dot at the
top of the leftmost display digit will light
following the final unsuccessful attempt. If the
inverter balance detection is not utilized, this dot
will not light.
PHM199R
1
2
3
4
Out-of-Balance Condition
High Water Level
Medium Water Level
Low Water Level
●
●
●
Water level – The computer attempts to maintain
the water level programmed for the fill preceding
the agitation step. If the level falls below the
programmed level, the computer will stop the
time countdown and re-energize the fill valves
until the level is restored.
Figure 3
Table 1 describes the function of the individual keys
when the machine is in Run Mode.
Water level in a heat step – In order for the
computer to energize the heat output, there must
be at least a low water level in the machine. If this
minimum level is not detected, the heat output
will be turned off until the required level is
restored.
Keypad
Key
Description
Up
Used in cycle selection; pressing this key
moves among cycles from smaller to greater.
Temperature probe problem – If the
temperature sensor fails when prompted for
degrees Fahrenheit, the computer flashes “tSFL”
in Program Mode rather than showing the
temperature. If the temperature sensor fails when
prompted for degrees Celsius, the display will
read “-17C” rather than showing the temperature.
Down
Used in cycle selection; pressing this key
moves among cycles from greater to smaller.
Start
Stop
Used to start a cycle.
Used to stop a cycle.
Table 1
F232123
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Table 2 lists the various displays and what they mean.
The operator should become familiar with these
computer displays.
Display Indications
Display
Lo
Display
Meaning
Meaning
Low water level
Medium water level
High water level
Supply 1
Program identification code (ROM)
These are examples only.
FPC3, bP3
nEd
HI
Hold
CY
Wait...power has just been turned on.
Cycle (followed by two-digit number)
SUP1
SUP2
SUP3
SUP4
SUP5
SUP6
SUP7
SLo/For**
SLo/rEv**
norn/For
norn/rEv
drAI
tESt/CYC* Test cycle selected.
Supply 2
FAr
Degrees Fahrenheit
Supply 3
CEL
Degrees Celsius
Supply 4
HEAt
noHt
tFIL
Auxiliary heat enabled.
Supply 5 (SETUP option)
Auxiliary heat disabled.
Supply 6 (supply 1 and 5)
Temperature-controlled fill enabled.
Temperature-controlled fill disabled.
Automatic cool-down enabled.
Automatic cool-down disabled.
Agitation 1 selected (90% agitation).
Agitation 2 selected (33% agitation).
Agitation 3 selected (10% agitation).
Agitation 4 selected (6.7% agitation).
Agitation speed normal
Supply 7 (supply 3 and 4)
ntFL
CooL
noCL
Ag 1
Ag 2
Ag 3
Ag 4
AgSn
AgSL**
PUnP
nPnP
PrE
Gentle wash speed, forward direction
Gentle wash speed, reverse direction
Normal wash speed, forward direction
Normal wash speed, reverse direction
Drain enabled.
nodr
Drain disabled.
dISt
Distribution (load balancing before extract)
Reads “SPIn” for one second, then “tInE” followed by
time for spin.
SPIn/tInE*
Agitation speed low
Pump output enabled (future use only).
Pump output disabled (future use only).
PreWash segment (1st of 11 segments)
Wash segment (2nd of 11 segments)
First fill (3rd of 11 segments)
Second fill (4th of 11 segments)
Third fill (5th of 11 segments)
Fourth fill (6th of 11 segments)
Fifth fill (7th of 11 segments)
Sixth fill (8th of 11 segments)
Seventh fill (9th of 11 segments)
Eighth fill (10th of 11 segments)
Ninth fill (11th of 11 segments)
Cold fill
SPn1
SPn2
SPn3
STOP
SdLY
donE
dFLt
door
Lowest of three spins
Middle of three spins
Highest of three spins
Stop routine
UASH
FIL1
FIL2
FIL3
FIL4
FIL5
FIL6
FIL7
FIL8
FIL9
CFIL
bFIL
HFIL
AFIL
SPC?
Spin coast delay
Cycle and stop routine have ended.
Drive fault detected.
Door not properly closed.
Balancing routine failed during test cycle after
7 attempts to balance load.
bAL/FAIL*†
FILL/STOP*
FULL
Programmed water level not reached after
30 minutes.
The computer detects low water level or higher when
none should be present.
Warm fill (both hot and cold)
Hot fill
Computer detects possible rotation of motor when there
should be none.
rotA
Auxiliary fill (SETUP option)
tSFL
Temperature sensor failure or temperature out of range.
Special test cycle function (if present, ignore)
Special test cycle function (if present, ignore)
bAL?
* Display indications separated by a slash represent a flashing display.
** For UW100VV and UW125VV models, the washer-extractor will operate at normal wash speed regardless of the speed settings.
† This occurs only in the TEST cycle and only if the AC inverter drive balance detection is used. If the AC inverter drive balance detection is not used, this
will NOT appear during the TEST cycle (note, there are two types of balance systems).
Table 2
F232123
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
When loading is complete, ensure that all fabric is
inside the basket. Then close and lock the door by
rotating the door handle clockwise until the door
handle is horizontal. The machine should not start or
run unless the door is both closed and locked.
Start-Up
Turn on the main power source (circuit breaker or cut-
off switch on the wall).
An identification code will appear for approximately
five seconds. Then the display will flash “Hold”
briefly.
CAUTION
The display will then read “CY” followed by a two-
digit cycle number (01 – 30) to indicate that a cycle
can be selected. This display will be shown at all times
when power is on between cycles, indicating that the
door-unlock solenoid will function if the door-unlock
button is pressed. The machine is then ready for
loading and unloading.
Check the door safety interlock daily
before the machine is placed in operation.
SW024
NOTE: When washing items which may
disintegrate, such as mop heads or sponges, use
laundry net bags to prevent drain blockage.
Opening Door
Cycle Selection
Press and hold the door-unlock button next to the door
handle and turn door handle upward.
NOTE: Press keys at their centers just hard enough
to activate them.
Loading
Press the Up or Down key until the desired cycle
number is displayed. The computer will skip blank
(unprogrammed) cycles automatically. Press the Start
key to start the cycle. For a more detailed description
of the preprogrammed cycles, refer to the cycle charts
at the end of the Programming section.
CAUTION
Be careful around the open door,
particularly when loading from a level
below the door. Impact with door edges
If the computer detects that the door is not properly
closed when the Start key is pressed, the display will
read “door” until the door is closed and locked. Press
Start again to begin the desired cycle.
can cause personal injury.
SW025
Load the machine to full capacity whenever possible,
but do not exceed the rated dry-weight capacity of the
machine if the fabric to be washed is quite dense,
closely woven, and heavily soiled. Overloading can
result in an inferior wash. The operator may need to
experiment to determine load size based on fabric
content, soil content, and level of cleanliness required.
NOTE: Washing small loads can cause out-of-
balance conditions which shorten life of bearing,
seals, basket/shaft assembly, etc.
WARNING
Never operate the machine with a
bypassed or disconnected balance
system. Operating the machine with
severe out-of-balance loads could result
in personal injury and serious equipment
damage.
SW039
F232123
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Download from Www.Somanuals.com. All Manuals Search And Download.
15
Operation
Wash
Cycle Execution
As soon as water level is reached (and any
programmed temperature is reached), the displayed
time begins counting down at one-second intervals.
A cycle can be stopped at any time by pressing the
Stop key. The machine will go to the stop routine.
When the routine is complete, the display shows
“donE” until the door is unlocked.
Agitation is active during this portion of the segment.
There are four different agitation actions available.
To display the temperature of the water while a cycle
is running, press the Up key. To display the number of
the cycle in progress, press the Start key.
Agitation Action Options
NOTE: The computer does not count down the
remaining cycle time during fills, drains, cool-
down, or prior to first achieving the programmed
heat temperature when heating. The computer
resumes counting down cycle time once the
programmed fill level is reached, when the machine
has drained, and after a programmed heat
temperature is reached.
Display
Description
Percentage
27 seconds forward,
3 seconds pause,
27 seconds reverse,
3 seconds pause
Ag 1
90%
10 seconds forward,
20 seconds pause,
10 seconds reverse,
20 seconds pause
Ag 2
Ag 3
Ag 4
33%
10%
6.7%
Each of the 30 cycles consists of 11 segments:
PreWash, Wash, and Fills 1 – 9. A description of the
various steps in a cycle segment follows:
3 seconds forward,
27 seconds pause,
3 seconds reverse,
27 seconds pause
Fill
After the Start key is pressed, the drain closes and the
machine begins filling to the programmed level. Each
programmed segment begins with a fill. The display
counts down the remaining cycle time in minutes and
seconds while the cycle is running.
4 seconds forward,
56 seconds pause,
4 seconds reverse,
56 seconds pause
If a supply is programmed in a step, the supply
dispenser will flush during the fill of that segment.
Table 3
If the segment contains a heat step, the machine begins
heating after the water has reached the programmed
level.
If the machine is connected to an external chemical
supply system, the programmed supply will begin
10 seconds into the fill. The supply will remain on
until the programmed water level is reached, or until
60 seconds have elapsed, whichever happens first.
NOTE: If the water does not reach the
programmed temperature in 40 minutes, the
computer progresses to the wash step.
If agitation options 1 or 2 are selected for the cycle
program, the cylinder will rotate slowly during the fill
step. If agitation options 3 or 4 are selected for the
cycle program, the cylinder will not rotate during the
If the computer does not receive a signal that water
level has been attained within 30 minutes, it will
alternately flash “STOP” and “FILL” and sound the
on-board beeper for ten seconds. The computer will
then initiate the stop routine.
F232123
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Download from Www.Somanuals.com. All Manuals Search And Download.
16
Operation
Drain
Stop Routine
If the cycle program segment calls for a drain, the
drain valves will open after the programmed segment
time has elapsed. If a spin step follows a drain step, the
cylinder will turn clockwise (forward) at wash speed
for several seconds at the beginning of the drain step.
This clockwise direction mirrors the spin rotation and
is, therefore, also considered forward.
When the computer concludes the wash cycle or when
the Stop key is pressed while a cycle is in progress, the
computer goes into the stop routine.
The stop routine sequence:
●
All inputs are turned off
●
A brief pause, allowing the cylinder to coast
down if in extract
The cylinder then accelerates to distribution speed to
help ensure that the load is evenly distributed. The
drains open several seconds later.
●
●
●
●
●
●
Brief rotation counterclockwise at wash speed
A brief pause
NOTE: The machine should drain in 30 seconds. If
the machine fails to drain, contact a qualified
service technician.
Brief rotation clockwise at wash speed
A brief pause
If the cycle program segment does not call for a drain,
the computer moves to the next segment of the cycle
program. If the segment is at the end of a cycle
program, the computer goes into the stop routine.
The display shows “donE”
The door interlock is energized, allowing the
door to be opened
If the stop routine seems excessively long, check for
“FULL” or “rotA” messages. If this occurs, contact a
qualified service technician.
If the cycle program segment does not call for a spin,
the cylinder will continue to turn at wash speed
throughout the drain step. When the drain has
completed, the computer moves to the next segment of
the cycle program. If the segment is at the end of a
cycle program, the computer goes into the stop
routine.
WARNING
NEVER insert hands or objects into
basket until it has completely stopped.
NOTE: The drain step in the final segment (Fill 9)
cannot be skipped.
Doing so could result in serious injury.
SW012
Spin
Once “donE” is displayed, open the door by pressing
and holding the door-unlock button as described
earlier. Once the door is opened, the computer display
will show the most recent cycle number.
After the drain sequence ends, the speed of the
cylinder increases to the extract speed if the
programmed spin time is not zero. The displayed time
resumes counting down at one-second intervals.
The machine is now ready to begin another wash
cycle.
After the programmed spin time has elapsed, the
computer moves on to the fill step in the next segment
of the cycle. If the spin is at the end of the cycle, the
computer begins the stop routine.
NOTE: A test cycle is provided as a means of
verifying proper machine operation. Refer to the
Programming section for instructions on running
the test cycle.
F232123
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Download from Www.Somanuals.com. All Manuals Search And Download.
17
Balance Detection
Motor Thermal Overload Indicator
Each machine is equipped with either an AC inverter
drive balance detection system or an overtravel limit
switch balance detection system. To determine which
system the machine is equipped with, consult the
wiring diagram sent with the machine.
If the machine is equipped with a small indicator lamp
on the side of the control module, it will light to
indicate that a thermal overload switch in the motor
has shut off the AC power to the computer board,
thereby preventing damage to the motor caused by
overheating and/or an overload condition. This feature
protects and extends the life of the motor.
Overtravel Limit Switch Balance Detection
This system uses the overtravel limit switch only; the
AC drive balance detection system is not utilized. As
the cylinder is spinning at the programmed speed, if
the wash load becomes unbalanced, the overtravel
limit switch is “tripped” causing the cylinder to slow
to a stop until the end of the spin step.
The thermal overload switch will automatically reset
itself after the excessive heat condition has subsided.
Before attempting to restart the washer-extractor,
determine the reason for the overload. The following is
a partial list of possible problems:
●
●
●
●
●
●
Washer-extractor not fully drained before spin
Out-of-balance condition
AC Inverter Drive Balance Detection
Load balance is monitored by the AC inverter drive
during any drain step that immediately precedes a spin
step.
Low voltage
Loss of one phase on a three-phase motor
Bad bearings
If a spin step follows a drain step, the cylinder
accelerates to distribution speed seven seconds into the
drain step.
Air circulation blocked to motor
Contact a service technician to correct serious
problems. Failure to take corrective action will
ultimately result in damage to the motor and/or the
inverter drive.
The computer begins monitoring the balance signal
from the AC inverter drive eight seconds after the
water level drops below low level. If the balance signal
indicates that the wash load is evenly distributed, the
computer will start the spin step.
If the balance signal indicates that the wash load is
unbalanced, the computer will slow the cylinder down
to wash speed for seven seconds in an attempt to
redistribute the load. The computer will make as many
as seven attempts if needed.
If on the seventh attempt the load is not balanced, the
machine will light the out-of-balance LED indicator
located in the upper left corner of the display (to the
left of the first digit) until the drain step is complete.
The machine will then continue the spin speed at a
safe level.
If this occurs in the final segment, the machine will
skip the spin step and initiate the stop routine. The out-
of-balance LED indicator will remain lit until the door
is opened.
As a fail-safe measure, an overtravel limit switch will
“trip” during a spin if the wash load becomes severely
unbalanced, slowing the cylinder to a stop until the end
of the spin step.
F232123
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Download from Www.Somanuals.com. All Manuals Search And Download.
18
Programming
The V-computer board is inside the control module.
Near the center of the board is a small toggle switch:
this is the Run/Program Mode switch.
Key Functions in Program Mode
Up – The Up key is used to increase cycle numbers
(1 through 30) and other numerical values such as
times or temperatures (when creating wash formulas).
WARNING
Down – The Down key is used to decrease cycle
numbers (1 through 30) and other numerical values
such as times or temperatures (when creating wash
formulas).
Dangerous voltages are present in the
electrical control box(es) and at the motor
terminals. Only qualified personnel
familiar with electrical test procedures,
test equipment, and safety precautions
should attempt adjustments and
Start – The Start key acts as an enter key in Program
Mode. Use this key to enter data and move to the next
function in the cycle.
troubleshooting. Disconnect power from
the machine before removing the control
box cover, and before attempting any
Stop – The Stop key saves all data and terminates the
programming procedure. If it is the first key pressed in
Program Mode, the computer enters Setup Mode. The
Stop key can be pressed again to exit Setup Mode and
return to Program Mode.
service procedures.
SW005
The Run/Program switch is normally in the down (Run
Mode) position. To enter Program Mode, flip the
switch to the up position. The display will now show
the current temperature in the sump.
Setup Mode
Setup options are programmable options that are in
effect for all wash formulas. These options include:
●
●
●
●
●
Degrees displayed in Fahrenheit or Celsius
Auxiliary heat enabled or disabled
1
Supply 5 or Auxiliary fill
Temperature-controlled fill enabled or disabled
Automatic cool-down enabled or disabled
NOTE: These options can be read or changed only
in Setup Mode.
To enter Setup Mode, press the Stop key while the
display is showing the temperature in the sump. Once
in Setup Mode, use the Up or Down key to change the
selected option. Use the Start key to accept the
selected option and move on to the next one. Press the
Stop key to exit Setup Mode.
2
CHM474R
1
2
Run/Program Mode Switch
Temperature Calibration Screw
Figure 4
Since the keypad operates in a slightly different
fashion when in Program Mode, pay careful attention
to the programming instructions provided in this
manual.
F232123
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Download from Www.Somanuals.com. All Manuals Search And Download.
19
Programming
Degrees Displayed in Fahrenheit or
Celsius
WARNING
This setup option affects the programming and display
of all temperatures. If “FAr” is selected, all
temperatures will display in Fahrenheit. If “CEL” is
selected, all temperatures will display in Celsius.
Acceptable ranges for programmable temperatures are
75° – 200°F or 25° – 93°C.
NEVER insert hands or objects into
basket until it has completely stopped.
Doing so could result in serious injury.
SW012
6. Restore input power to the machine.
7. Wait until machine message displays “CY”
followed by a two-digit cycle number (01 – 30).
Procedure for Temperature Calibration
1. Ensure that the V-Computer has no input power
applied.
8. Program one of the unused cycles to Fill to High
Level using both of the water inlet valves. Select
a time limit that would be sufficient to complete
the calibration procedure.
2. Mount an accurate temperature sensor probe
(part of temperature calibration equipment) in the
bottom of the machine basket. Make sure the
wires for the probe exit the top of the door to
ensure the door gasket does not leak.
9. When machine has completed the Fill to High
Level, press and hold the Up key to display the
machine temperature. Make sure that the
V-Computer is in the correct temperature unit
(deg F or C). Refer to Setup Mode section of
manual to change.
3. Close door and ensure that the door is locked.
4. Open machine top cover and remove control
component cover(s), if necessary, to gain access
to the V-Computer and output control board.
10. Using a flat bladed screwdriver, turn the machine
temperature calibration screw until the displayed
temperature of the machine and the temperature
of the temperature calibration equipment are
NOTE: For more accurate calibration proceed with
steps 5-9. For a quick estimated calibration skip to
step 10.
11. When the temperatures match, calibration is
completed.
WARNING
12. Remove power from the machine input.
Dangerous voltages are present in the
electrical control box(es) and at the motor
terminals. Only qualified personnel
familiar with electrical test procedures,
test equipment, and safety precautions
should attempt adjustments and
13. Reconnect any wires/connectors/fuses that were
removed, making sure they are installed exactly
as they were removed.
14. Reinstall all machine protective covers.
15. Remove the temperature calibration probe from
the bottom of the machine basket.
troubleshooting. Disconnect power from
the machine before removing the control
box cover, and before attempting any
16. Restore input power to machine.
17. Machine is now ready for use.
service procedures.
SW005
5. Note wire connections on the output control
board for the AC Drive control. Some machines
will have six wires connected to “STF,” “STR,”
“RH,” “RM,” “RL,” and “COM” individually or a
single connector labeled “J11-1.” Remove these
wires or connector to ensure the basket will not
rotate. Also remove the input power to the drive.
NOTE: If this step is not followed, damage can
occur to the calibration temperature probe.
F232123
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Download from Www.Somanuals.com. All Manuals Search And Download.
20
Programming
Auxiliary Heat
Cycle Count
Heat is a dedicated output of the V-computer, which
controls an optional heat source. If “noHt” is selected,
the heat output will never energize during a cycle
(except briefly in the test cycle to ensure that the
output functions properly), regardless of programmed
temperature settings. If “HEAt” is selected, the output
will energize during a cycle if the three following
conditions are true:
To display the current cycle count, press the Start key
while the display is showing the temperature in the
sump. The display will show a two-digit number
indicating how many cycles have been run to
completion (cycles which were stopped in progress are
not counted). Press the Start key to return to Program
Mode without resetting the count. Press the Up or
Down key to reset the count to zero and return to
Program Mode.
●
A nonzero heat temperature is programmed.
●
The computer senses that the present temperature
is below the programmed target temperature.
Cycle Programming
To edit an existing cycle or create a new cycle, press
the Up key while the display is showing the
temperature in the sump. The display will show
“CY01.” Press the Up or Down key until the desired
cycle number is displayed. Press the Start key to begin
editing the selected cycle.
●
There is at least a low water level in the machine.
NOTE: Do not enable the auxiliary heat setup
option and disable the temperature-controlled fill
option on machines not equipped with auxiliary
heat. The machine will pause for 40 minutes during
any cycle segment where the fill water temperature
does not equal or exceed the programmed value of
the heat step.
Supply 5 or Auxiliary Fill
If “SUP5” is selected, the output labeled AF on the
solid state output board can be used to control a fifth
supply signal. This setup option must be selected to
program an “SUP5” or an “SUP6” (supply 1 and
supply 5 combined) in a cycle step.
If “AFIL” is selected, the output labeled AF can be
used to control an auxiliary fill valve. Auxiliary fills
can be programmed to low, medium, or high water
level. This setup option must be selected to program an
“AFIL” in a cycle step.
Temperature-Controlled Fill
If “tFIL” is selected, a temperature-controlled fill can
be programmed for any segment. This setup option
must be selected to program a “tFIL” in a cycle step. If
“ntFL” is selected, this feature is disabled.
Automatic Cool-Down
If “CooL” is selected, the automatic cool-down feature
is enabled. If the wash solution is 140°F (60°C) or
higher when a cycle step calls for a drain, the washing
action will continue and the cold water valve will
begin flushing cold water into the wash solution. Once
the wash solution temperature drops below 140°F
(60°C), the drains open and the cycle continues as
programmed. If “noCL” is selected, this feature is
disabled.
F232123
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Download from Www.Somanuals.com. All Manuals Search And Download.
21
Programming
Cycle Options
Agitation Speed
Cycle options are programmable options that are in
effect for the duration of the selected wash cycle.
These options include:
If “AgSn” or “AgSL” is selected, the machine will
default to normal wash speed regardless of the setting.
Recirculation Pump
●
Agitation action
This cycle option setting is intended to be used with
a possible future recirculation application. Selecting
either “nPnP” or “PUnP” will have no bearing on
the wash cycle. However, the “nPnP” setting is
recommended to prevent the corresponding output
on the output board from energizing.
●
Agitation speed (defaults to normal wash speed
regardless of setting)
●
Recirculation pump enabled or disabled (for
possible future application)
NOTE: Cycle option settings are unique to the cycle
for which they are programmed.
Press the Start key after selecting this last cycle option
setting to begin editing the cycle segments.
Use the Up or Down key to change the selected option.
Use the Start key to accept the selected option and
move on to the next one.
Segment Programming
All cycle programs (“CY01” – “CY30”) can be
customized within a preset program structure. Each
cycle program consists of eleven program segments.
Agitation Action
The programmer may choose among four agitation
Cycle Program Segments
Agitation Action Options
Segment
PreWash
Wash
Fill 1
Display
PrE
Display
Description
Percentage
27 seconds forward,
3 seconds pause,
27 seconds reverse,
3 seconds pause
UASH
FIL1
FIL2
FIL3
FIL4
FIL5
FIL6
FIL7
FIL8
FIL9
Ag 1
90%
Fill 2
10 seconds forward,
20 seconds pause,
10 seconds reverse,
20 seconds pause
Fill 3
Ag 2
Ag 3
Ag 4
33%
10%
6.7%
Fill 4
3 seconds forward,
27 seconds pause,
3 seconds reverse,
27 seconds pause
Fill 5
Fill 6
Fill 7
4 seconds forward,
56 seconds pause,
4 seconds reverse,
56 seconds pause
Fill 8
Fill 9
Table 5
Table 4
The selected agitation applies to the entire cycle. It is
possible to progam a different agitation action for each
of the 30 cycles. When “Ag 3” or “Ag 4” is in effect,
there is no agitation during the fill.
F232123
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Programming
NOTE: The computer does not count down the
remaining cycle time during fills, drains, cool-
down, or prior to first achieving the programmed
heat temperature when heating. The computer
resumes counting down cycle time once the
programmed fill level is reached, when the machine
has drained, and after a programmed heat
temperature is reached.
When modifying a cycle, a time must be entered for
each segment. To skip a segment or spin, set the time
parameters for each segment and spin, as well as the
allowable temperature range.
Time and Temperature Parameters
Function
PreWash
Minimum
2 minutes
Maximum
3. If the temperature-controlled fill setup option is
enabled, the display will show “tFIL.” Press the
Start key.
30 minutes
20 minutes
15 minutes
15 minutes
15 minutes
15 minutes
15 minutes
15 minutes
15 minutes
15 minutes
15 minutes
240 seconds
10 minutes
200°F (93°C)
Wash
2 minutes
2 minutes
2 minutes
2 minutes
2 minutes
2 minutes
2 minutes
2 minutes
2 minutes
2 minutes
30 seconds
1 minute
4. Use the Up or Down key to select the desired fill
Fill 1
Fill 2
Fill Temperature Options
Fill 3
Display
Fill Type
Fill 4
CFIL
HFIL
bFIL
AFIL
Cold Fill
Hot Fill
Fill 5
Fill 6
Warm Fill
Fill 7
Auxiliary Fill*
Fill 8
*This is available only if the “SUP5”/“AFIL” setup
option is set to “AFIL.”
Fill 9
Table 7
Intermediate Spin*
Final Spin**
Temperature
If the temperature-controlled fill setup option is
enabled and a target temperature is set, the
selected fill valve(s) will energize for the first
three seconds of the segment fill. The computer
will then begin operating the fill valves in an
attempt to reach the target temperature. Press the
Start key.
75°F (25°C)
* Programmed with wash segment through Fill 8.
** Programmed with Fill 9.
Table 6
5. Use the Up or Down key to select the desired fill
NOTE: Spin times in cycle segments 1 – 10 are
entered in seconds (30 to 240), and time for final
spin in segment 11 is entered in minutes (1 to 10).
Water Level Options
Display
Fill Level
1. Press the Up key until the computer display
shows the segment to be edited. Press the Start
key.
Lo
nEd
HI
Low Level
Medium Level
High Level
2. Use the Up or Down key to select the desired
segment time. Set this value to zero to skip the
segment. Press the Start key.
Table 8
F232123
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Programming
6. Press the Start key.
10. Use the Up or Down key to select the desired
drain option. If “drAI” is selected, the machine
will drain after the segment time has elapsed. If
“nodr” is selected, the machine will not drain and
the spin step will be skipped entirely. Press the
Start key.
7. Use the Up or Down key to select the desired
Supply Options
Display
Supply
NOTE: The drain step in the final segment (Fill 9)
cannot be skipped.
SUP0
SUP1
SUP2
SUP3
SUP4
SUP5
SUP6
SUP7
No Supply
Supply 1
11. For final “FIL9” spin only, use the Up or
Down key to select the desired spin speed.
Supply 2
Spin Options
Supply 3
Display
Spin Speed
Supply 4
Supply 5*
SPn1
SPn2
SPn3
Low Spin
Medium Spin
High Spin
Supply 1 and 5*
Supply 3 and 4
*This is available only if the “SUP5”/“AFIL” setup
option is set to “SUP5.”
Table 10
12. Press the Start key.
Table 9
13. Use the Up or Down key to select the desired spin
time. Set this value to zero to skip the spin step.
Press the Start key. The display will now show
the identifier for the next program segment (or
return to the temperature display if the edited
segment is the Fill 9 segment).
8. Press the Start key.
9. If the temperature-controlled fill or the auxiliary
heat setup option is enabled, use the Up or Down
key to select the desired segment temperature. To
disable auxiliary heat and temperature-controlled
fill for this segment, set this value to zero. Press
the Start key.
NOTE: Every intermediate spin is followed by a
25 second coast-down period, which occurs during
the fill step for the following segment.
NOTE: If the temperature-controlled fill setup
option is enabled and an auxiliary fill has been
selected for the segment, the segment temperature
should be set to zero. Otherwise, the auxiliary fill
valve will enable for only three seconds at the
beginning of the fill before the computer begins
using the hot and cold fill valves to reach the
programmed temperature.
14. Press the Stop key at any time to complete the
cycle programming procedure.
F232123
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Download from Www.Somanuals.com. All Manuals Search And Download.
24
Programming
g. The auxiliary heat output is energized,
Test Cycle
provided that the water level switch indicates
that at least low water level is present. The
cold water fill valve is energized. The supply
1 output is energized for five seconds. The
display alternately flashes “SUP1” and
“HEAt” (supply 1 output on, auxiliary heat
output on).
1. Verify that the Run/Program Mode toggle switch
is in the Run position.
2. Press the Up or Down key until the display
alternately flashes “tESt” and “CYC,” indicating
that the test cycle is selected.
3. Press the Start key to begin the test cycle.
h. The supply 2 output is energized for five
seconds. The display alternately flashes
“SUP2” and “HEAt” (supply 2 output on,
auxiliary heat output on).
NOTE: If “bAL?” or “SPC?” appear on display,
ignore it; computer will proceed automatically.
NOTE: Pressing the Start key while the test cycle is
in progress will immediately advance to the next
step in the test cycle. Drain and load balancing
steps may not be skipped.
i. The supply 3 output is energized for five
seconds. The display alternately flashes
“SUP3” and “HEAt” (supply 3 output on,
auxiliary heat output on).
The test cycle is as follows:
j. The auxiliary heat output is turned off. The
supply 4 output is energized for five seconds.
The display shows “SUP4” (supply 4 output
on).
a. Once the Start key is pressed, the door
interlock is de-energized (preventing the door
from being opened), the drain valve closes,
the cylinder begins agitating at wash speed,
and both water inlet valves are energized. The
display alternately flashes “bFIL” and “Lo”
(both hot and cold fill valves on, filling to low
level).
k. The supply 5/auxiliary fill output energizes
for five seconds. If the “SUP5”/“AFIL” setup
option is set to “SUP5,” the display shows
“SUP5” (supply 5/auxiliary fill output on).
If the “SUP5”/“AFIL” setup option is set
to “AFIL,” the display shows “AFIL”
b. When the water level switch indicates that low
water level has been reached, the water fill
valves shut off and the dot above and to the
immediate left of the fourth digit of the
display lights.
(supply 5/auxiliary fill output on).
l. The cold water fill valve turns off. The
recirculation pump output is energized for
ten seconds, provided that the water level
switch indicates that at least low water level
is present. The display shows “PUnP”
(recirculation pump output on).
c. The cold water fill valve is energized. The
display alternately flashes “CFIL” and “nEd”
(cold fill valve on, filling to medium water
level).
m. The motor rotates counterclockwise
(in reverse) at normal wash speed for
60 seconds. The display alternately flashes
“SLo” and “rEv” (normal wash speed,
counterclockwise).
d. When the water level switch indicates that
medium water level has been reached, the
cold water fill valve shuts off and the dot
above and to the immediate left of the third
digit of the display lights.
n. The motor rotates clockwise (forward) at
normal wash speed for 60 seconds. The
display alternately flashes “SLo” and “For”
(normal wash speed, clockwise).
e. The hot water fill valve is energized. The
display alternately flashes “HFIL” and “HI”
(hot fill valve on, filling to high water level).
o. The motor rotates counterclockwise (in
reverse) at normal wash speed for 60 seconds.
The display alternately flashes “norn” and
“rEv” (normal wash speed,
f. When the water level switch indicates that
high water level has been reached, the hot
water fill valve shuts off and the dot above
and to the immediate left of the second digit
of the display lights.
counterclockwise).
F232123
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Download from Www.Somanuals.com. All Manuals Search And Download.
25
Programming
p. The motor rotates clockwise (forward) at
v. The cylinder accelerates to low spin speed.
The display shows “SPn1” (cylinder rotating
at low spin speed). The basket rotates at low
spin speed for 60 seconds.
normal wash speed for 60 seconds. The
display alternately flashes “norn” and “For”.
q. The display begins alternately flashing “drAI”
and “For” (drain step, cylinder rotating at
wash speed). The motor continues to rotate
clockwise (forward) at normal wash speed for
seven seconds.
w. The cylinder accelerates to medium spin
speed. The display shows “SPn2” (cylinder
rotating at medium spin speed). The basket
rotates at medium spin speed for 60 seconds.
r. The motor accelerates to distribution speed.
The display alternately flashes “drAI” and
“dISt” (drain step, cylinder rotating at
distribution speed).
x. The cylinder accelerates to high spin speed.
The display shows “SPn3” (cylinder rotating
at high spin speed). The basket rotates at high
spin speed for 60 seconds.
s. The drain opens between 15 to 27 seconds
into the drain step. The water level indicator
lights on the display will begin to go out, one
by one, as the machine drains past each water
level.
y. All outputs are turned off for roughly
20 seconds. The display shows “SdLY”
(spin coast delay).
z. The computer performs the normal stop
routine.
t. The computer begins monitoring the balance
signal from the AC inverter drive several
seconds after the water level switch indicates
that water level has dropped below low level.
The door interlock is energized (allowing the
door to be opened), provided that the water
level switch indicates that water has fallen
below low level and that the AC drive
indicates that the motor has stopped.
u. If the balance signal indicates that the wash
load is unbalanced, the cylinder will slow
down to wash speed for seven seconds in an
attempt to redistribute the load. The computer
will make as many as seven attempts, as
needed, in this cycle.
NOTE: If the machine utilizes the overtravel limit
switch balance detection system, the computer will
proceed through the drain step and will time steps t
and u. The computer will then proceed to step v.
F232123
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Download from Www.Somanuals.com. All Manuals Search And Download.
26
Programming
Cycle Segment Charts
Segment 1 (PreWash)
Instructions
Use Up or Down key to change. Press Start key to enter or advance.
Display
PrE
00 or 02 to 30
tFIL
Select segment time: 02 to 30 minutes (00 to skip segment).
Indicates temperature fill is enabled.*
HFIL, CFIL, bFIL,
or AFIL
Select “HFIL” (hot fill), “CFIL” (cold fill), “bFIL” (warm fill), or “AFIL” (auxiliary fill).**
Lo, nEd, or HI
SUP0 – SUP7
Select fill level: “Lo” (low), “nEd” (medium), or “HI” (high) water level.
Select supply 0 – 7 (0 for no supply).***
00°F, 75° – 200°F
00°C, 25° – 93°C
Select temperature: 75° to 200°F or 25° to 93°C (00 for no heat).†
drAI or nodr
Select drain option: “drAI” (drain), “nodr” (no drain).‡
SPIn (flashed for one second)
tInE (flashed for one second)
00 or 30 to 240
Select time for spin: 30 to 240 seconds (00 for no spin).
* This is displayed only if temperature-controlled fills are enabled in the setup options and if the heat temperature is set to
a value other than “00.”
** “AFIL” can be selected only if the “SUP5”/“AFIL” setup option is set to “AFIL.”
***“SUP5” and “SUP6” can be selected only if the “SUP5”/“AFIL” setup option is set to “SUP5.”
† This value is not available when temperature-controlled fill and auxiliary heat setup options are disabled.
‡ If “nodr” is selected, the computer skips the spin step and goes on to the next segment.
F232123
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Programming
Segment 2 (Wash)
Instructions
Display
Use Up or Down key to change. Press Start key to enter or advance.
UASH
00 or 02 to 20
tFIL
Select segment time: 02 to 20 minutes (00 to skip segment).
Indicates temperature fill is enabled.*
HFIL, CFIL, bFIL,
or AFIL
Select “HFIL” (hot fill), “CFIL” (cold fill), “bFIL” (warm fill), or “AFIL” (auxiliary fill).**
Lo, nEd, or HI
SUP0 – SUP7
Select fill level: “Lo” (low), “nEd” (medium), or “HI” (high) water level.
Select supply 0 – 7 (0 for no supply).***
00°F, 75° – 200°F
00°C, 25° – 93°C
Select temperature: 75° to 200°F or 25° to 93°C (00 for no heat).†
drAI or nodr
Select drain option: “drAI” (drain), “nodr” (no drain).‡
SPIn (flashed for one second)
tInE (flashed for one second)
00 or 30 to 240
Select time for spin: 30 to 240 seconds (00 for no spin).
* This is displayed only if temperature-controlled fills are enabled in the setup options and if the heat temperature is set to
a value other than “00.”
** “AFIL” can be selected only if the “SUP5”/“AFIL” setup option is set to “AFIL.”
***“SUP5” and “SUP6” can be selected only if the “SUP5”/“AFIL” setup option is set to “SUP5.”
† This value is not available when temperature-controlled fill and auxiliary heat setup options are disabled.
‡ If “nodr” is selected, the computer skips the spin step and goes on to the next segment.
F232123
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Programming
Segments 3 – 10 (Fills 1 – 8)
Instructions
Use Up or Down key to change. Press Start key to enter or advance.
Display
FIL1, FIL2, FIL3, FIL4, FIL5, FIL6, FIL7, or FIL8
00 or 02 to 15
tFIL
Select segment time: 02 to 15 minutes (00 to skip segment).
Indicates temperature fill is enabled.*
HFIL, CFIL, bFIL,
or AFIL
Select “HFIL” (hot fill), “CFIL” (cold fill), “bFIL” (warm fill), or “AFIL” (auxiliary fill).**
Lo, nEd, or HI
SUP0 – SUP7
Select fill level: “Lo” (low), “nEd” (medium), or “HI” (high) water level.
Select supply 0 – 7 (0 for no supply).***
00°F, 75° – 200°F
00°C, 25° – 93°C
Select temperature: 75° to 200°F or 25° to 93°C (00 for no heat).†
drAI or nodr
Select drain option: “drAI” (drain), “nodr” (no drain).‡
SPIn (flashed for one second)
tInE (flashed for one second)
00 or 30 to 240
Select time for spin: 30 to 240 seconds (00 for no spin).
* This is displayed only if temperature-controlled fills are enabled in the setup options and if the heat temperature is set to
a value other than “00.”
** “AFIL” can be selected only if the “SUP5”/“AFIL” setup option is set to “AFIL.”
*** “SUP5” and “SUP6” can be selected only if the “SUP5”/“AFIL” setup option is set to “SUP5.”
† This value is not available when temperature-controlled fill and auxiliary heat setup options are disabled.
‡ If “nodr” is selected, the computer skips the spin step and goes on to the next segment.
F232123
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Programming
Segment 11 (Fill 9)
Instructions
Display
Use Up or Down key to change. Press Start key to enter or advance.
FIL9
00 or 02 to 15
tFIL
Select segment time: 02 to 15 minutes (00 to skip segment).
Indicates temperature fill is enabled.*
HFIL, CFIL, bFIL,
or AFIL
Select “HFIL” (hot fill), “CFIL” (cold fill), “bFIL” (warm fill), or “AFIL” (auxiliary fill).**
Lo, nEd, or HI
SUP0 – SUP7
Select fill level: “Lo” (low), “nEd” (medium), or “HI” (high) water level.
Select supply 0 – 7 (0 for no supply).***
00°F, 75° – 200°F
00°C, 25° – 93°C
Select temperature: 75° to 200°F or 25° to 93°C (00 for no heat).†
drAI or nodr
Select drain option: “drAI” (drain), “nodr” (no drain).
SPn1, SPn2, or SPn3
Select spin speed: “SPn1” (low), “SPn2” (medium), or “SPn3” (high).
SPIn (flashed for one second)
tInE (flashed for one second)
00 or 01 to 10
Select time for spin: 1 to 10 minutes (00 for no spin).
* This is displayed only if temperature-controlled fills are enabled in the setup options and if the heat temperature is set to
a value other than “00.”
** “AFIL” can be selected only if the “SUP5”/“AFIL” setup option is set to “AFIL.”
***“SUP5” and “SUP6” can be selected only if the “SUP5”/“AFIL” setup option is set to “SUP5.”
† This value is not available when temperature-controlled fill and auxiliary heat setup options are disabled.
F232123
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Programming
V-Computer Cycle Charts
V-Computer Standard OPL Cycles
7
8
1
2
3
4
5
6
Table
Table
Permanent
Press
Light Soil
Cotton
Terrycloth
Permanent
Press
Cotton
Terrycloth
Permanent
Press
Cotton
Terrycloth
Program
Napery
Blends
Colors
Napery
Blends
Whites
Light Soil Medium Soil Medium Soil Heavy Soil Heavy Soil
Agitation
Wash Speed
Pump
Ag 1
AgSn
nPnP
Ag 1
AgSn
nPnP
Ag 1
AgSn
nPnP
Ag 1
AgSn
nPnP
Ag 1
AgSn
nPnP
Ag 1
AgSn
nPnP
Ag 1
AgSn
nPnP
Ag 1
AgSn
nPnP
PreWash
Time (Min)
Water
0
0
2
Warm
High
0
2
Warm
High
0
2
Warm
High
0
2
Warm
High
0
2
Warm
High
0
2
Warm
High
0
---
---
---
---
---
---
---
---
---
---
---
---
Level
Supply
Temp (F)
Drain
0
0
0
0
0
0
DrAI
0
DrAI
0
DrAI
0
DrAI
0
DrAI
0
DrAI
0
Spin (Sec)
Wash
Time (Min)
Water
7
Hot
Low
1
7
Hot
Low
1
7
Hot
Low
1
7
Hot
Low
1
6
Hot
Low
1
6
Hot
Low
1
9
Hot
Low
1
9
Hot
Low
1
Level
Supply
Temp (F)
Drain
0
0
0
0
0
0
0
0
DrAI
0
DrAI
0
DrAI
0
DrAI
0
DrAI
0
DrAI
0
DrAI
0
DrAI
0
Spin (Sec)
Fill 1
Time (Min)
Water
4
Hot
High
0
4
Hot
High
0
7
Hot
Low
2
7
Hot
Low
2
7
Hot
Low
1
7
Hot
Low
1
4
Hot
High
0
7
Hot
Low
2
Level
Supply
Temp (F)
Drain
0
0
0
0
0
0
0
0
DrAI
0
DrAI
0
DrAI
0
DrAI
0
DrAI
0
DrAI
0
DrAI
0
DrAI
0
Spin (Sec)
Fill 2
Time (Min)
Water
2
Warm
High
0
2
Warm
High
0
4
Hot
High
0
4
Hot
High
0
7
Hot
Low
2
7
Hot
Low
2
2
Warm
High
0
4
Hot
High
0
Level
Supply
Temp (F)
Drain
0
0
0
0
0
0
0
0
DrAI
30
DrAI
60
DrAI
0
DrAI
0
DrAI
0
DrAI
0
DrAI
30
DrAI
0
Spin (Sec)
Fill 3
Time (Min)
Water
4
Warm
Low
3
0
2
Warm
High
0
2
Warm
High
0
4
Hot
High
0
4
Hot
High
0
4
Warm
Low
3
2
Warm
High
0
---
---
---
---
---
---
Level
Supply
Temp (F)
Drain
0
0
0
0
0
0
0
DrAI
240
DrAI
30
DrAI
0
DrAI
60
DrAI
0
DrAI
240
DrAI
30
Spin (Sec)
F232123
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Programming
V-Computer Standard OPL Cycles (Continued)
7
8
1
2
3
4
5
6
Table
Table
Permanent
Press
Light Soil
Cotton
Terrycloth
Permanent
Press
Cotton
Terrycloth
Permanent
Press
Cotton
Terrycloth
Program
Napery
Blends
Colors
Napery
Blends
Whites
Light Soil Medium Soil Medium Soil Heavy Soil Heavy Soil
Fill 4
Time (Min)
Water
0
0
4
Warm
Low
3
0
2
Warm
High
0
2
Warm
High
0
0
4
Warm
Low
3
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
Level
Supply
Temp (F)
Drain
0
0
0
0
DrAI
240
DrAI
30
DrAI
30
DrAI
240
Spin (Sec)
Fill 5
Time (Min)
Water
0
0
0
0
4
Warm
Low
3
0
0
0
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
Level
Supply
Temp (F)
Drain
0
DrAI
240
Spin (Sec)
Fill 6
Time (Min)
Water
0
0
0
0
0
0
0
0
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
Level
Supply
Temp (F)
Drain
Spin (Sec)
Fill 7
Time (Min)
Water
0
0
0
0
0
0
0
0
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
Level
Supply
Temp (F)
Drain
Spin (Sec)
Fill 8
Time (Min)
Water
0
0
0
0
0
0
0
0
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
Level
Supply
Temp (F)
Drain
Spin (Sec)
Fill 9
Time (Min)
Water
0
4
Warm
Low
3
0
4
Warm
Low
3
0
4
Warm
Low
3
0
0
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
Level
Supply
Temp (F)
Drain
0
0
0
---
DrAI
SPn3
5
DrAI
SPn3
5
Spin
SPn3
5
Spin (Min)
F232123
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Programming
V-Computer Standard OPL Cycles (Continued)
9
10
13
Personals
with
14
Personals
no
15
16
VISA
VISA
Table
11
12
Reclaim
Delicates
Spreads
Delicates
Spreads
Program
Table
Napery
Colors
Rags
Napery
Whites
Heavy Soil
Bleach
Bleach
Cold Water Warm Water
Agitation
Wash Speed
Pump
Ag 1
AgSn
nPnP
Ag 1
AgSn
nPnP
Ag 1
AgSn
nPnP
Ag 1
AgSn
nPnP
Ag 1
AgSn
nPnP
Ag 1
AgSn
nPnP
Ag 1
AgSn
nPnP
Ag 1
AgSn
nPnP
PreWash
Time (Min)
Water
2
Warm
High
0
2
Warm
High
0
2
Warm
High
1
2
Hot
High
1
2
Warm
High
1
2
Warm
High
0
0
0
---
---
---
---
---
---
---
---
---
---
---
---
Level
Supply
Temp (F)
Drain
0
0
0
0
0
0
DrAI
0
DrAI
0
DrAI
0
DrAI
0
DrAI
0
DrAI
0
Spin (Sec)
Wash
Time (Min)
Water
10
Hot
Low
1
10
Hot
Low
1
10
Hot
Low
1
6
Hot
Low
1
7
Hot
Low
2
7
Hot
Low
1
5
Cold
High
1
7
Warm
High
1
Level
Supply
Temp (F)
Drain
0
0
0
0
0
0
0
0
DrAI
0
DrAI
0
DrAI
0
DrAI
0
DrAI
0
DrAI
0
DrAI
0
DrAI
0
Spin (Sec)
Fill 1
Time (Min)
Water
6
Hot
Low
1
6
Hot
Low
1
6
Hot
Low
2
12
Hot
Low
2
2
Warm
High
0
2
Warm
High
0
4
Cold
High
0
4
Warm
High
0
Level
Supply
Temp (F)
Drain
0
0
0
0
0
0
0
0
DrAI
0
DrAI
0
DrAI
0
DrAI
0
DrAI
0
DrAI
0
DrAI
0
DrAI
0
Spin (Sec)
Fill 2
Time (Min)
Water
4
Hot
High
0
4
Hot
High
0
4
Hot
High
2
4
Hot
High
0
2
Warm
High
0
2
Warm
High
0
2
Cold
High
0
2
Warm
High
0
Level
Supply
Temp (F)
Drain
0
0
0
0
0
0
0
0
DrAI
0
DrAI
0
DrAI
0
DrAI
0
DrAI
30
DrAI
30
DrAI
30
DrAI
30
Spin (Sec)
Fill 3
Time (Min)
Water
2
Warm
High
0
2
Warm
High
0
2
Warm
High
0
2
Warm
High
0
4
Warm
Low
3
4
Warm
Low
3
4
Cold
High
3
4
Warm
High
3
Level
Supply
Temp (F)
Drain
0
0
0
0
0
0
0
0
DrAI
0
DrAI
0
DrAI
0
DrAI
0
DrAI
240
DrAI
240
DrAI
240
DrAI
240
Spin (Sec)
F232123
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Programming
V-Computer Standard OPL Cycles (Continued)
9
10
13
Personals
with
14
Personals
no
15
16
VISA
VISA
Table
11
12
Reclaim
Delicates
Spreads
Delicates
Spreads
Program
Table
Napery
Colors
Rags
Napery
Whites
Heavy Soil
Bleach
Bleach
Cold Water Warm Water
Fill 4
Time (Min)
Water
2
Cold
High
0
2
Cold
High
0
2
Warm
High
0
2
Warm
High
0
0
0
0
0
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
Level
Supply
Temp (F)
Drain
0
0
0
0
DrAI
30
DrAI
30
DrAI
60
DrAI
30
Spin (Sec)
Fill 5
Time (Min)
Water
4
Cold
Low
3
4
Cold
Low
3
4
Warm
High
0
4
Warm
Low
3
0
0
0
0
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
Level
Supply
Temp (F)
Drain
0
0
0
0
DrAI
240
DrAI
240
DrAI
60
DrAI
240
Spin (Sec)
Fill 6
Time (Min)
Water
0
0
0
0
0
0
0
0
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
Level
Supply
Temp (F)
Drain
Spin (Sec)
Fill 7
Time (Min)
Water
0
0
0
0
0
0
0
0
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
Level
Supply
Temp (F)
Drain
Spin (Sec)
Fill 8
Time (Min)
Water
0
0
0
0
0
0
0
0
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
Level
Supply
Temp (F)
Drain
Spin (Sec)
Fill 9
Time (Min)
Water
0
0
4
Warm
Low
3
0
0
0
0
0
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
Level
Supply
Temp (F)
Drain
0
DrAI
SPn3
6
Spin
Spin (Min)
NOTE: Preprogrammed cycles 17 – 20 are blank.
F232123
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Programming
V-Computer Export OPL Cycles
26
28
21
22
23
24
Normal
60°C
25
Normal
40°C
27
Permanent
Press
29
30
Fine
40°C
Permanent
Press
90°C
(PreWash)
Permanent
Press
60°C
(PreWash)
Normal Normal Normal
90°C
(PreWash)
Permanent
Press
Program
90°C
60°C
(PreWash)
(PreWash)
90°C
60°C
Agitation
Wash Speed
Pump
Ag 1
AgSn
nPnP
Ag 1
AgSn
nPnP
Ag 1
AgSn
nPnP
Ag 1
AgSn
nPnP
Ag 1
AgSn
nPnP
Ag 1
AgSn
nPnP
Ag 1
AgSn
nPnP
Ag 1
AgSn
nPnP
Ag 1
AgSn
nPnP
Ag 2
AgSn
nPnP
PreWash
Time (Min)
Water
8
Cold
High
1
0
8
Cold
High
1
0
6
Cold
High
1
8
Cold
High
1
0
8
Cold
High
1
0
6
Cold
High
1
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
Level
Supply
Temp (C)
Drain
40°
DrAI
0
40°
DrAI
0
40°
DrAI
0
40°
DrAI
0
40°
DrAI
0
40°
DrAI
0
Spin (Sec)
Wash
Time (Min)
Water
10
Hot
Low
2
10
Hot
Low
2
10
Hot
Low
2
10
Hot
Low
2
8
Both
Low
2
10
Hot
Low
2
10
Hot
Low
2
10
Hot
Low
2
10
Hot
Low
2
8
Both
Low
2
Level
Supply
Temp (C)
Drain
90°
DrAI
0
90°
DrAI
0
60°
DrAI
0
60°
DrAI
0
40°
DrAI
0
90°
DrAI
0
90°
DrAI
0
60°
DrAI
0
60°
DrAI
0
40°
DrAI
0
Spin (Sec)
Fill 1
Time (Min)
Water
0
0
0
0
0
0
0
0
0
0
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
Level
Supply
Temp (C)
Drain
Spin (Sec)
Fill 2
Time (Min)
Water
0
0
0
0
0
0
0
0
0
0
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
Level
Supply
Temp (C)
Drain
Spin (Sec)
Fill 3
Time (Min)
Water
2
Cold
Medium
0
2
Cold
Medium
0
2
Cold
Medium
0
2
Cold
Medium
0
2
Cold
Medium
0
2
Cold
Medium
0
2
Cold
Medium
0
2
Cold
Medium
0
2
Cold
Medium
0
2
Cold
Medium
0
Level
Supply
Temp (C)
Drain
0
0
0
0
0
0
0
0
0
0
DrAI
30
DrAI
30
DrAI
30
DrAI
30
DrAI
30
DrAI
30
DrAI
30
DrAI
30
DrAI
30
DrAI
30
Spin (Sec)
F232123
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Programming
V-Computer Export OPL Cycles (Continued)
26
28
21
22
23
24
Normal
60°C
25
Normal
40°C
27
Permanent
Press
29
Permanent
Press
30
Fine
40°C
Permanent
Press
90°C
(PreWash)
Permanent
Press
60°C
(PreWash)
Normal Normal Normal
90°C
(PreWash)
Program
90°C
60°C
(PreWash)
(PreWash)
90°C
60°C
Fill 4
Time (Min)
Water
2
Cold
Medium
0
2
Cold
Medium
0
2
Cold
Medium
0
2
Cold
Medium
0
2
Cold
Medium
0
2
Cold
Medium
0
2
Cold
Medium
0
2
Cold
Medium
0
2
Cold
Medium
0
2
Cold
Medium
0
Level
Supply
Temp (C)
Drain
0
0
0
0
0
0
0
0
0
0
DrAI
30
DrAI
30
DrAI
30
DrAI
30
DrAI
30
DrAI
30
DrAI
30
DrAI
30
DrAI
30
DrAI
30
Spin (Sec)
Fill 5
Time (Min)
Water
2
Cold
Medium
0
2
Cold
Medium
0
2
Cold
Medium
0
2
Cold
Medium
0
2
Cold
Medium
0
2
Cold
Medium
0
2
Cold
Medium
0
2
Cold
Medium
0
2
Cold
Medium
0
2
Cold
Medium
0
Level
Supply
Temp (C)
Drain
0
0
0
0
0
0
0
0
0
0
DrAI
30
DrAI
30
DrAI
30
DrAI
30
DrAI
30
DrAI
30
DrAI
30
DrAI
30
DrAI
30
DrAI
30
Spin (Sec)
Fill 6
Time (Min)
Water
0
0
0
0
0
0
0
0
0
0
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
Level
Supply
Temp (C)
Drain
Spin (Sec)
Fill 7
Time (Min)
Water
0
0
0
0
0
0
0
0
0
0
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
Level
Supply
Temp (C)
Drain
Spin (Sec)
Fill 8
Time (Min)
Water
0
0
0
0
0
0
0
0
0
0
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
Level
Supply
Temp (C)
Drain
Spin (Sec)
Fill 9
Time (Min)
Water
2
2
2
2
2
2
2
2
2
2
Cold
Cold
Cold
Cold
Cold
Cold
Cold
Cold
Cold
Cold
Level
Medium
Medium
Medium
Medium
Medium
Medium
Medium
Medium
Medium
Medium
Supply
Temp (C)
Spin
3
0
3
0
3
0
3
0
3
0
3
0
3
0
3
0
3
0
3
0
SPn3
6
SPn3
6
SPn3
6
SPn3
6
SPn3
6
SPn3
2
SPn3
2
SPn3
2
SPn3
2
SPn2
2
Spin (Min)
F232123
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Programming
Cycle Programming Worksheet
Program
PreWash
Time (Min)
Wash
Fill 3
Fill 6
Fill 9
Title
Time (Min)
Water
Water
Level
Level
Cycle
Supply
Temp
Supply
Temp
Agitation
Wash Speed
Pump
Drain
Drain
Spin (Sec)
Spin (Sec)
Fill 1
Fill 4
Fill 7
Fill 2
Time (Min)
Time (Min)
Water
Time (Min)
Water
Water
Level
Level
Level
Supply
Temp
Supply
Temp
Supply
Temp
Drain
Drain
Drain
Spin (Sec)
Spin (Sec)
Spin (Sec)
Fill 5
Time (Min)
Water
Time (Min)
Water
Time (Min)
Water
Level
Level
Level
Supply
Temp
Supply
Temp
Supply
Temp
Drain
Drain
Drain
Spin (Sec)
Spin (Sec)
Spin (Sec)
Fill 8
Time (Min)
Water
Time (Min)
Water
Time (Min)
Water
Level
Level
Level
Supply
Temp
Supply
Temp
Supply
Temp
Drain
Drain
Spin
Spin (Sec)
Spin (Sec)
Spin (Min)
F232123
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
|