26-Port 10/100/1000Mbps
Gigabit & Fast Ethernet Switch
2 × 1000BASE plus
24 × 10/100BASE ports
User Guide
ASW-2402
Download from Www.Somanuals.com. All Manuals Search And Download.
26-port 10/100/1000Mbps Gigabit & Fast Ethernet Switch
ULWarning
a) Elevated Operating Ambient Temperature- If installed in a closed
or multi-unit rack assembly, the operating ambient temperature of
the rack environment may be greater than room ambient. Therefore,
consideration should be given to installing the equipment in an envi-
ronment compatible with the manufacturer’s maximum rated ambi-
ent temperature (Tmra).
b) Reduced Air Flow- Installation of the equipment in a rack should
be such that the amount of air flow required for safe operation of the
equipment is not compromised.
c) Mechanical Loading- Mounting of the equipment in the rack
should be such that a hazardous condition is not achieved due to
uneven mechanical loading.
d) Circuit Overloading- Consideration should be given to the con-
nection of the equipment to the supply circuit and the effect that
overloading of circuits might have on over current protection and
supply wiring. Appropriate consideration of equipment nameplate
ratings should be used when addressing this concern.
e) Reliable Earthing- Reliable earthing of rack-mounted equipment
should be maintained. Particular attention should be given to supply
connections other than direct connections to the branch circuit (e.g.,
use of power strips).
AirLink+
3
Download from Www.Somanuals.com. All Manuals Search And Download.
26-port 10/100/1000Mbps Gigabit & Fast Ethernet Switch
4
AirLink+
Download from Www.Somanuals.com. All Manuals Search And Download.
26-port 10/100/1000Mbps Gigabit & Fast Ethernet Switch
TABLE OF CONTENTS
ABOUT THIS GUIDE ............................................................. 1
PURPOSE ............................................................................................... 1
TERMS/USAGE ....................................................................................... 1
INTRODUCTION ................................................................... 3
FAST ETHERNET TECHNOLOGY ................................................................. 3
GIGABIT ETHERNET TECHNOLOGY ............................................................. 4
SWITCHING TECHNOLOGY ......................................................................... 5
FEATURES .............................................................................................. 6
UNPACKINGANDINSTALLATION .................................... 7
UNPACKING ............................................................................................ 7
INSTALLATION .......................................................................................... 8
RACK MOUNTING ................................................................................... 9
CONNECTING NETWORK CABLE ..............................................................10
AC POWER .........................................................................................10
IDENTIFYING EXTERNAL COMPONENTS ....................11
FRONT PANEL ......................................................................................11
REAR PANEL ........................................................................................12
UNDERSTANDING LED INDICATORS ........................... 13
POWER LED ......................................................................................13
PORTS 1~24 STATUS LEDS .................................................................13
PORT 25 & PORT 26 STATUS LEDS ....................................................14
TECHNICALSPECIFICATIONS ....................................... 15
AirLink+
5
Download from Www.Somanuals.com. All Manuals Search And Download.
26-port 10/100/1000Mbps Gigabit & Fast Ethernet Switch
About This Guide
Congratulations on your purchase of the 26-Port 10/100/1000Mbps
Gigabit & Ethernet Switch with 2 x 1000BASE-T plus 24 x 10/
100BASE-TX ports. This device integrates Gigabit, 100Mbps Fast
Ethernet, and 10Mbps Ethernet network capabilities in a highly
flexible package.
Purpose
This guide discusses how to install your 26-Port 10/100/1000Mbps
Gigabit & Ethernet Switch with 2 x 1000BASE-T plus 24 x 10/
100BASE-TX ports.
Terms/Usage
In this guide, the term “Switch” (first letter upper case) refers to
your 26-Port 10/100/1000Mbps Gigabit & Ethernet Switch with
2 x 1000BASE-T plus 24 x 10/100BASE-TX ports, and “switch”
(first letter lower case) refers to other Ethernet switches.
6
AirLink+
Download from Www.Somanuals.com. All Manuals Search And Download.
26-port 10/100/1000Mbps Gigabit & Fast Ethernet Switch
Introduction
This chapter describes the features of the Switch and some back-
ground information about Ethernet/Fast Ethernet/Gigabit Ethernet
switching technology.
Fast Ethernet Technology
The growing importance of LANs and the increasing complexity of
desktop computing applications are fueling the need for high perfor-
mance networks. A number of high-speed LAN technologies have
been proposed to provide greater bandwidth and improve client/
server response times. Among them, 100BASE-T (Fast Ethernet)
provides a non-disruptive, smooth evolution from the current
10BASE-T technology. The non-disruptive and smooth evolution
nature, and the dominating potential market base, virtually guarantee
cost-effective and high performance Fast Ethernet solutions.
100Mbps Fast Ethernet is a standard specified by the IEEE 802.3
LAN committee. It is an extension of the 10Mbps Ethernet standard
with the ability to transmit and receive data at 100Mbps, while
maintaining the CSMA/CD Ethernet protocol. Since the 100Mbps
Fast Ethernet is compatible with all other 10Mbps Ethernet envi-
ronments, it provides a straightforward upgrade and takes advantage
of the existing investment in hardware, software, and personnel train-
ing.
AirLink+
7
Download from Www.Somanuals.com. All Manuals Search And Download.
26-port 10/100/1000Mbps Gigabit & Fast Ethernet Switch
Gigabit Ethernet Technology
Gigabit Ethernet is an extension of IEEE 802.3 Ethernet utilizing the
same packet structure, format, and support for CSMA/CD proto-
col, full duplex, flow control, and management objects, but with a
tenfold increase in theoretical throughput over 100-Mbps Fast
Ethernet and a hundredfold increase over 10-Mbps Ethernet. Since it
is compatible with all 10-Mbps and 100-Mbps Ethernet environ-
ments, Gigabit Ethernet provides a straightforward upgrade without
wasting a company’s existing investment in hardware, software, and
trained personnel.
The increased speed and extra bandwidth offered by Gigabit Ethernet
are essential to coping with the network bottlenecks that frequently
develop as computers and their busses get faster and more users
using applications that generate more traffic. Upgrading key compo-
nents, such as your backbone and servers to Gigabit Ethernet can
greatly improve network response times as well as significantly speed
up the traffic between your subnets.
Gigabit Ethernet supports video conferencing, complex imaging, and
similar data-intensive applications. Likewise, since data transfers
occur 10 times faster than Fast Ethernet, servers outfitted with Giga-
bit Ethernet NIC’s are able to perform 10 times the number of opera-
tions in the same amount of time.
The phenomenal bandwidth delivered by Gigabit Ethernet was the
most cost-effective method to take advantage of today’s rapidly
improving switching and routing internetworking technologies. And
with expected advances in silicon technology and digital signal pro-
cessing that enabled Gigabit Ethernet to eventually operate over
unshielded twisted-pair (UTP) cabling, outfitting your network with
a powerful 1000-Mbps-capable backbone/server connection creates
a flexible foundation for the next generation of network technology
products.
8
AirLink+
Download from Www.Somanuals.com. All Manuals Search And Download.
26-port 10/100/1000Mbps Gigabit & Fast Ethernet Switch
Switching Technology
Another approach to pushing beyond the limits of Ethernet technol-
ogy is the development of switching technology. A switch bridges
Ethernet packets at the MAC address level of the Ethernet protocol
transmitting among connected Ethernet or Fast Ethernet LAN seg-
ments.
Switching is a cost-effective way of increasing the total network
capacity available to users on a local area network. A switch in-
creases capacity and decreases network loading by dividing a local
area network into different segments, which don’t compete with
each other for network transmission capacity.
The switch acts as a high-speed selective bridge between the indi-
vidual segments. The switch, without interfering with any other
segments, automatically forwards traffic that needs to go from one
segment to another. By doing this the total network capacity is
multiplied, while still maintaining the same network cabling and adapter
cards.
Switching LAN technology is a marked improvement over the previ-
ous generation of network bridges, which were characterized by higher
latencies. Routers have also been used to segment local area net-
works, but the cost of a router, the setup and maintenance required
make routers relatively impractical. Today switches are an ideal
solution to most kinds of local area network congestion problems.
AirLink+
9
Download from Www.Somanuals.com. All Manuals Search And Download.
26-port 10/100/1000Mbps Gigabit & Fast Ethernet Switch
Features
ꢀ
24×10/100BASE-TX Fast Ethernet ports +
2×1000BASE-T Gigabit Ethernet ports
Auto MDI-X for each port
Full/half duplex transfer mode for 10/100Mbps Fast
Ethernet ports
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
Full duplex transfer mode for Gigabit Ethernet ports
Wire speed reception and transmission
Store-and-Forward switching method
Integrated address Look-Up Engine, supports 8K MAC
addresses
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
Supports 2.5Mbit RAM for data buffering
Extensive front-panel diagnostic LEDs
IEEE 802.3x flow control for full-duplex
Back pressure flow control for half-duplex
Standard 19” Rack-mount size
10
AirLink+
Download from Www.Somanuals.com. All Manuals Search And Download.
26-port 10/100/1000Mbps Gigabit & Fast Ethernet Switch
Unpacking and Installation
This chapter provides unpacking and installation information for the
Switch. To avoid causing any damage to the Switch, we recommend
that you read this chapter carefully before starting installation.
Unpacking
Open the shipping carton of the Switch and carefully unpack the
items inside. The carton should contain the following items:
ꢀ
One 26-Port 10/100/1000Mbps Gigabit & Ethernet
Switch
ꢀ
One AC power cord, suitable for your area’s electrical
power connections
ꢀ
ꢀ
ꢀ
Four rubber feet to be used for shock cushioning
Screws and two mounting brackets
User’s Guide
If any item is found missing or damaged, please contact your local
reseller for replacement.
AirLink+
11
Download from Www.Somanuals.com. All Manuals Search And Download.
26-port 10/100/1000Mbps Gigabit & Fast Ethernet Switch
Installation
The site where you place the Switch may greatly affect its perfor-
mance. When installing, take the following into your consideration:
ꢀ
Install the Switch in a fairly cool and dry place. See
Technical Specifications for the acceptable temperature and
humidity operating ranges.
ꢀ
Install the Switch in a site free from strong electromag-
netic field generators (such as motors), vibration, dust,
and direct exposure to sunlight.
ꢀ
ꢀ
Leave at least 10cm of space at the front and rear of the
hub for ventilation.
Install the Switch on a sturdy, level surface that can
support its weight, or in an EIA standard-size equipment
rack. For information on rack installation, see the next
section, Rack Mounting.
ꢀ
When installing the Switch on a level surface, attach the
rubber feet to the bottom of each device. The rubber feet
cushion the hub and protect the hub case from scratch-
ing.
12
AirLink+
Download from Www.Somanuals.com. All Manuals Search And Download.
26-port 10/100/1000Mbps Gigabit & Fast Ethernet Switch
Figure 1. Attach the adhesive rubber pads to the bottom
Rack Mounting
The Switch can be mounted in an EIA standard-size, 19-inch rack,
which can be placed in a wiring closet with other equipments. Attach
the mounting brackets to both sides of the Switch (one at each side),
and secure them with the provided screws.
Figure 2. Combine the Switch with the provided screws
Then, use screws provided with the equipment rack to mount the
Switch in the rack.
AirLink+
13
Download from Www.Somanuals.com. All Manuals Search And Download.
26-port 10/100/1000Mbps Gigabit & Fast Ethernet Switch
Figure 3. Mount the Switch in the rack
Connecting Network Cable
The Switch supports 10/100/1000Mbps Gigabit Ethernet. It runs
full/half duplex transfer mode for 10/100Mbps and full duplex trans-
fer mode for 1000Mbps.
These ports are Auto-MDI type port. The Switch can auto trans-
form to MDI-II or MDI-X type, so you can just make an easy
connection that without worrying if you are using a standard or
crossover cable.
AC Power
The Switch can be used with AC power supply 100-240VAC, 50-60
Hz. The power switch is located at the rear of the unit adjacent to the
AC power connector and the system fan. The switch’s power sup-
ply will adjust to the local power source automatically and may be
turned on without having any or all LAN segment cables connected.
14
AirLink+
Download from Www.Somanuals.com. All Manuals Search And Download.
26-port 10/100/1000Mbps Gigabit & Fast Ethernet Switch
Identifying External Components
This chapter identifies all the major external components of the Switch.
Both the front and rear panels are shown below, with a description of
each panel features.
Front Panel
Figure 4. The front panel of the Switch
ꢀ
LED Indicators
Refer to the next chapter Understanding LED Indicators for detailed
information on the meaning of each LED indicator.
ꢀ
10/100BASE-TX Twisted-Pair Ports (Port1~24)
These ports supports network speeds of either 10Mbps or 100Mbps,
and can operate in half- and full- duplex transfer modes. These ports
also supports automatic MDI/MDI-X crossover detection function
gives true “plug and play” capability, just need to plug-in the net-
work cable to the hub directly and no need to care if the end node is
NIC (Network Interface Card) or switches and hubs.
ꢀ
1000BASE-T Twisted Pair Ports (Port 25~26)
The Switch is equipped with two Gigabit twisted pair ports, sup-
ported auto negotiable 10/100/1000Mbps and auto MDI/MDIX
crossover detection function. These two ports can operate in half-
and full- duplex modes.
AirLink+
15
Download from Www.Somanuals.com. All Manuals Search And Download.
26-port 10/100/1000Mbps Gigabit & Fast Ethernet Switch
Rear Panel
Figure 5. The rear panel of the Switch
ꢀC Power Connector
This is a three-pronged connector that supports the power cord.
Plug in the female connector of the provided power cord into this
connector, and the male into a power outlet. Supported input volt-
ages range from 100-240V AC at 50-60Hz.
16
AirLink+
Download from Www.Somanuals.com. All Manuals Search And Download.
26-port 10/100/1000Mbps Gigabit & Fast Ethernet Switch
Understanding LED Indicators
The front panel LEDs provides instant status feedback, and, helps
monitor and troubleshoot when needed.
Power LED
ꢀ
POWER
On : When the Power LED lights on, the Switch is receiving power.
Off : When the Power LED turns off or the power cord has improper
connection.
Ports 1~24 Status LEDs
ꢀ
LINK/ACT
On : When the LED lights on, the respective port is connected to the
10/100Mbps Ethernet network.
Blinking : When the LED is blinking, the port is transmitting or
receiving data on the 10/100Mbps Ethernet network.
Off : No link.
AirLink+
17
Download from Www.Somanuals.com. All Manuals Search And Download.
26-port 10/100/1000Mbps Gigabit & Fast Ethernet Switch
ꢀ
100Mbps
On : When the LED lights on, the respective port is connected to a
100Mbps Ethernet network.
Off : The respective port is connected to a 10Mbps Ethernet
network, or no link
Port 25 & Port 26 Status LEDs
ꢀ
LINK/ACT
On : When the LED lights on, the respective port is connected to a
10/100/1000Mbps Ethernet network.
Blinking : When the LED is blinking, the respective port is transfer-
ring or receiving data on a 10/100/1000Mbps Ethernet network.
Off : No link.
ꢀ
1000Mbps
On : When the LED lights on, the respective port is connected to a
Gigabit Ethernet network.
Off : The respective port is connected to a 10/100Mbps Ethernet
network, or no link.
ꢀ
100Mbps
On : When the LED lights on, the respective port is connected to a
100Mbps Fast Ethernet network.
Off : The respective port is connected to a 10Mbps or Gigabit
Ethernet network, otherwise, no link.
18
AirLink+
Download from Www.Somanuals.com. All Manuals Search And Download.
26-port 10/100/1000Mbps Gigabit & Fast Ethernet Switch
Technical Specifications
Technical Support
E-mail: [email protected]
Toll Free: 1-888-746-3238
AirLink+
19
Download from Www.Somanuals.com. All Manuals Search And Download.
26-port 10/100/1000Mbps Gigabit & Fast Ethernet Switch
Copyright 2004 AirLink+. All rights reserved. AirLink+, the stylized AirLink+ logo, specific product
designations, and all other words and logos that are identified as trademarks and/or service marks are,
unless noted otherwise, the trademarks and service marks of AirLink+. All other product or service names
are the property of their respective holders. AirLink+ products are protected under numerous U.S. and
foreign patents and pending applications, maskwork rights, and copyrights
20
AirLink+
1907EG7224T7050
Download from Www.Somanuals.com. All Manuals Search And Download.
|