AGA SIX-FOUR SERIES - DC6 (FFD)
OWNERS MANUAL
(L.P.G.)
DESN 512387 A
Comprising
Servicing, Installation & Users
Instructions
&
Cooking Guide
Remember, when replacing a part on this appliance, use only spare parts that you can be
assured conform to the safety and performance specification that we require. Do not use
reconditioned or copy parts that have not been clearly authorised by Aga.
PLEASE READ THESE INSTRUCTIONS BEFORE USING THIS APPLIANCE
For use in GB and IE
05/07 EINS 512453
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Section
Remember, when replacing a part on this appliance, use only spare parts that you can be
assured conform to the safety and performance specification that we require. Do not use
reconditioned or copy parts that have not been clearly authorised by Aga.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
WARNING: THIS APPLIANCE SHALL BE INSTALLED IN ACCORDANCE WITH THE
REGULATIONS IN FORCE AND ONLY USED IN A WELL VENTILATED SPACE, READ THE
INSTRUCTIONS BEFORE INSTALLING OR USING THIS APPLIANCE.
PRIOR TO INSTALLATION, ENSURE THAT THE LOCAL DISTRIBUTION CONDITIONS
(TYPE OF GAS AND GAS PRESSURE) AND THE ADJUSTMENTS OF THE APPLIANCE ARE
COMPATIBLE.
THE ADJUSTMENT CONDITIONS FOR THIS APPLIANCE ARE STATED ON THE DATA
PLATE WHICH IS SITUATED IN THE RIGHT HAND VENT SLOT AT THE BASE OF THE
APPLIANCE.
This appliance is not connected to a combustion products evacuation device. It must be installed
and connected in accordance with current installation regulations. Particular attention shall be
given to the relevant requirements regarding ventilation. (B.S. 5440 Part 2). It should be in
accordance also with any relevant requirements of the Gas Region and Local Authority.
In your own interest, and that of safety to comply with the law, all gas appliances must be
installed by a competent person. Failure to install appliances correctly could lead to prosecution.
On completion, test the gas installation for soundness.
WARNING: THIS APPLIANCE MUST BE EARTHED.
The appliance is designed for the voltage stated on the data plate.
The DC6 is supplied from the manufacturers as a fully tested chassis construction. Hot plate,
doors, splashback, pan supports and handrail are assembled during installation.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
TECHNICAL DATA
HOTPLATE
3+
PROPANE G30/G31 - (APPLIANCE CATEGORY I )
L.H.F.
WOK
ULTRA-RAPID RAPID
R.H.F.
R.H.R.
RAPID
3.0 kW
L.H.R.
CENTRE
FRONT
CENTRE
REAR
BURNER TYPE
SEMI-RAPID SEMI-RAPID ULTRA-RAPID
MAXIMUM HEAT
INPUT
4.0 kW
(287g/h)
3.0 kW
(215g/h) (215g/h)
1.75 kW
(125g/h)
1.75 kW
(125g/h)
5.0 kW
(360g/h)
INJECTOR MARKING
MAIN
SECONDARY
0.46
0.66
85
-
85
-
65
-
65
-
110
-
PRESSURE POINT POSITION: REAR RH SIDE OF HOTPLATE
PRESSURE SETTING: G30 = 28 mbar G31: 37mbar
BURNER IGNITION: H.T. SPARK
ELECTRIC GRILL AND OVENS
TOP OVEN POWER RATING - 1.45 kW
GRILL ELEMENT - POWER RATING 2.25kW
SLOW COOKING OVEN - POWER RATING 0.9kW
LOWER OVEN (FAN) - 2.0kW
230V 30 AMP POWER SUPPLY
This is a CLASS 1, type X appliance.
The data plaque is located on a pull out plate - lower front of appliance (See Fig. 10, Page 21).
5
Download from Www.Somanuals.com. All Manuals Search And Download.
FITTING AND PRODUCT DIMENSIONS
Any side wall above the cooker on either side shall be not less than 60mm horizontally from the
cooker (Fig. 1).
Surfaces over the top of the cooker must not be closer than 650mm.
A minimum clearance of 1000mm must be available at the front of the cooker to enable it to be
serviced.
The vent slots in the back of the top plate must not be obstructed.
The cooker must stand on a firm and level surface and we recommend that any soft material
such as linoleum is removed.
PLEASE NOTE: WHEN FITTING A COOKER HOOD
If a cooker hood is to be fitted, we only recommend the 6-4 Series CH900 cooker hood. It must
be installed at a height of at least 800mm above the hotplate.
DESN 512388 C
Fig. 1
6
Download from Www.Somanuals.com. All Manuals Search And Download.
ELECTRICAL CONNECTION
ELECTRICAL CONNECTION IS LOCATED AT THE TOP RIGHT HAND SIDE OF THE
APPLIANCE, BEHIND SIDE PANEL. DURING INSTALLATION REMOVE THE RIGHT HAND
SIDE PANEL TO CONNECT ELECTRICAL SUPPLY.
Remove 6 screws securing side panel to gain access to mains terminal. See Fig. 3 for location
of cover.
Remember that the mains electrical cable must be routed through the grommet at the rear right
hand side of the cooker near the top, before connecting to the mains terminal connection.
REFER TO FIG. 2 for wire connection to appliance.
Remember that an excess of cable length is required inside the cooker to allow for possible
servicing of the spark generator.
Remember that an excess of cable length is required behind the cooker for the withdrawal of the
cooker from between the kitchen units etc.
SINGLE PHASE CONNECTION - The cooker requires a 30amp power supply fitted in
conjunction with a Double Pole Isolator with a minimum contact clearance of 3mm and be
connected to the mains with a minimum 6mm2 cable to comply with the latest editions of the
Local and National Wiring Regulations.
THE ISOLATOR MUST NOT BE POSITIONED IMMEDIATELY ABOVE THE COOKER, BUT
MUST BE SITED WITHIN 2 METRES OF THE APPLIANCE.
Replace the right hand side panel once electrical connection has been made and replace fixing
screws.
NOTE: Ensure that the insulation card covering the mains terminal is in place, between the side
panel and mains terminal.
SINGLE PHASE CONNECTION - MINIMUM 6mm2 CABLE AND MUST COMPLY WITH THE
LATEST EDITIONS OF LOCAL AND NATIONAL WIRING REGULATIONS.
Fig. 2a
DESN 513312
7
Download from Www.Somanuals.com. All Manuals Search And Download.
THREE PHASE CONNECTION - MINIMUM 2.5mm2 AND MUST COMPLY WITH THE
LATEST EDITIONS OF THE LOCAL AND NATIONAL WIRING REGULATIONS.
Fig. 2b
DESN 513313 A
8
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTING TO GAS
To allow ease of servicing and cooker mobility, an approved flexible 4ft hose should be fitted.
Supply piping should not be less than R 1/2 (1/2” BSP). Connection is made to the R 1/2 (1/2”
BSP) female threaded entry in the inlet block located just below the hotplate level on the rear
right hand side of the cooker.
Fig. 3
DESN 512389
The gas bayonet connector must be fitted to the wall in the shaded area dimensioned in Fig. 4.
Take into account that it must be possible to pull the cooker forward sufficiently for servicing.
Ensure flexible hose is not trapped between cooker back panel and rear wall. Ensure hose is
routed within the shaded area and away from shielded oven vent. The flexible hose must be in
accordance with the relevant standards.
IMPORTANT: THE GAS SUPPLY CONNECTION AT THE WALL MUST NOT PROJECT OUT
FROM THE WALL BY MORE THAN 45MM, SO THAT IT DOES NOT FOUL WITH THE BACK
OF THE COOKER.
Check for gas soundness after connecting the appliance.
FLEXIBLE HOSE
The flexible hose must be suitable for use with Propane gas, capable of 70ÞC temperature rise,
and carry a red stripe, band or label. If in doubt contact your supplier.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
COOKER STABILITY
A stability bracket shall be secured firmly to the fabric of the building, when the appliance is
connected to the gas supply by a flexible hose. For positioning of bracket (See Fig. 3). A safety
chain must also be anchored firmly to the wall and cooker to prevent the flexible hose from
straining, when the cooker is withdrawn for servicing. When fitting a stability bracket and chain
refer to dimensions in Fig. 3 and Fig. 3A.
Fig. 3A
DESN 512384
10
Download from Www.Somanuals.com. All Manuals Search And Download.
POSITION OF GAS BAYONET ON WALL (locate in shaded areas)
IMPORTANT: THE GAS SUPPLY CONNECTION AT THE WALL MUST NOT PROJECT
OUT FROM THE WALL BY MORE THAN 45MM, SO THAT IT DOES NOT FOUL WITH THE
BACK OF THE COOKER.
Fig. 4
DESN 512390 A
PRESSURE TESTING
The pressure test point is situated at the rear right hand side of the hotplate.
Place the wok burner head, burner cap and ring into position on the hotplate. Light the burner by
pushing in the appropriate control knob, and turning it anti-clockwise IGNITION position, until gas
ignites, then continue to turn to the FULL ON position.
For LPG appliance (propane), the pressure should be 37mbar (14.8 inches water gauge).
Turn off the tap, disconnect the pressure gauge and refit test point blanking screw.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
LEVELLING AND MOBILITY WHEELS
INSTALLATION/LEVELLING
The DC6 is designed to stand on a flat and level surface, however, any unevenness may be
overcome by adjusting the four levelling feet, one at each corner of the base plate. The adjusting
screws are accessed by removing left and right hand hotplate castings (See section ‘To Remove
Hotplate Castings - Servicing Section Page 50). To raise the cooker turn screw clockwise, to
lower turn screw anti-clockwise.
Fig. 5
DESN 512391 B
There are rollers on the base of the cooker to allow for positioning.
When the cooker is in the correct position the four levelling feet can be adjusted to level the
cooker. THE FEET MUST BE LOWERED ENOUGH TO PREVENT THE COOKER ROLLING
OUT OF POSITION. (See Fig. 5)
12
Download from Www.Somanuals.com. All Manuals Search And Download.
FITTING OF HOTPLATE CASTING AND PAN SUPPORTS
HOTPLATE CASTINGS
1. Attach earth cable from centre casting to cooker chassis and locate over burner bodies.
Repeat for LH and RH castings and that the gaskets are fitted where the outer castings
overlap centre castings. Ensure that earth cables are attached. (See Fig. 6A)
Fig. 6A
DESN 512400 A
2. Secure castings using 8 profiled fixing nuts. DO NOT OVERTIGHTEN. (See Fig. 6B).
Fig. 6B
DESN 512393 C
13
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Fit and secure six burner rings using M4 screws on rear left hand, front centre, front right
hand and rear right hand burners. Use No.6 3/8 screw on front left hand and centre rear
burners. (See Fig. 6C).
NOTE: The fitting of LH and centre burners are the same as shown in Fig. 6B.
Fig. 6C
DESN 512419 A
4. Position burner caps onto burner bodies. (See Figs. 7A, 7B, & 7C).
ULTRA RAPID BURNER
WOK BURNER
Fig. 7A
DESN 513714
DESN 513512
14
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY OF RAPID AND SEMI-RAPID BURNERS
BURNER CAP
BURNER HEAD
ELECTRODE
Fig. 7B
DESN 511618
FITTING BURNER CAP - RAPID AND SEMI-RAPID
BURNERS
BURNER CAP
RETAINING LUGS
Fig. 7C
DESN 511617
15
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Fit the pan supports in the following order The pan supports are marked on the underside to
correspond to the markings below. The pan supports must locate in the recesses in the
hotplate casting. (See Fig. 8A & 8B)
Fig. 8A
DESN 513712 A
Important
It is very important for the performance and reliability of the hob that the pan supports are fitted
in accordance with the AGA SIX-FOUR SERIES - DC6 OWNERS MANUAL.
To help identify the correct location of the pan supports, the centre rear pan support has been
uniquely designed with a tag, as shown. This pan support must be fitted in the rear centre
position with the tag pointing towards the back of the appliance.
Fig. 8B
DESN 512995 A
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Fig. 8C
DESN 513716
TO ADJUST PAN SUPPORT LEVEL
1.
2.
3.
4.
Loosen retaining nut using 8mm spanner. (See Fig. 8C).
To prevent rocking adjust the pan support foot using 2.5mm allen key.
Check pan support is level with opposing pan supports.
Retighten retaining nut.
HANDRAIL FITTING
1.
2.
Position handrail assembly onto locating studs at each end of facia. Ensure the grub screw
at each end of the hand rail is facing downwards.
Push handrail assembly fully against facia and lock in place by tightening 2 grub screws
(2 1/2 mm). (See Fig. 6A).
SPLASHBACK
1. Locate tabs on rear of splashback assembly, into the brackets on the upper rear of the
cooker. (See Fig. 9).
Push fully into place.
Fig. 9
DESN 512394
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Users
Guide
18
Download from Www.Somanuals.com. All Manuals Search And Download.
GENERAL INFORMATION
As responsible manufacturers we take care to make sure that our products are designed and
constructed to meet the required safety standards when properly installed and used.
IMPORTANT NOTICE: PLEASE READ THE ACCOMPANYING WARRANTY.
Any alteration that is not approved by Aga could invalidate the approval of the appliance,
operation of the warranty and could affect your statutory rights.
In the interests of safety and effective use, please read the following before using your new Aga
appliance.
The use of gas on a cooking appliance results in the production of heat and moisture in the room
in which it is installed. Ensure that the kitchen is well ventilated, keep the natural ventilation holes
open or install a mechanical ventilation device (mechanical extractor hood).
Prolonged intensive use of the appliance may call for additional and/or more effective ventilation,
for example, opening of a window, or, increasing the level of mechanical ventilation where
present.
Installation must be to local and National IEE Wiring Regulations and carried out by a qualified
CORGI engineer, from an Authorised Distributor.
A little smoke and some odour may be emitted when first switched on. This is normal and
harmless (from oven lagging and starch binder on the element insulation) and will cease after a
short period of use.
Your appliance has a gas hob, three electric ovens; the lower right hand oven is a slow cooking
oven, the upper right hand oven is a conventional oven.
The lower left hand oven is an electric fan oven. The fan behind the rear panel ensures an even
distribution of heat within the oven during cooking, ie. the temperature at the lowest shelf position
is the same as the temperature at the highest shelf position.
The electric grill is situated in the roof of the top left hand compartment.
Refer to the diagram (See Fig. 10) to familiarise yourself with the cooker and refer to the relevant
section for the simmering oven, fan oven, conventional oven, grill and gas hotplate etc.
Your cooker is supplied with the following accessories:
5 oven shelves
1 large roasting tin
1 grill shelf
1 grill pan
1 grill grid
1 baking tray
1 cast iron frying pan
The following loose parts are also packed with:
6 pan supports (cast)
3 spillage wells (cast)
6 burner caps
6 burner heads
1 burner ring
1 handrail assembly
1 splashback assembly
1 fitting kit
6 burner skirts
2 spacer rings
6 gaskets
19
Download from Www.Somanuals.com. All Manuals Search And Download.
HEALTH & SAFETY
APPLIANCE
YOUNG CHILDREN SHOULD BE KEPTAWAY FROM THE APPLIANCE AS SOME SURFACES
CAN BECOME HOT TO TOUCH.
z
During use the appliance can become hot. Care should be taken to avoid touching heating
elements inside the oven.
Deep Fat Frying
z
z
z
z
Use a deep pan, large enough to completely cover the appropriate heating area.
Never fill the pan more than one-third full of fat or oil.
Never leave fat or oil unattended during the heating or cooking period.
Never use a lid on the pan.
z
z
IMPORTANT: Oil is a fire risk, do not leave pans containing oil unattended.
In the event of fire cover with a lid and turn OFF the appliance.
Do not attempt to extinguish the fire using water.
Smother the flames on the hob, rather than attempting to remove the pan to the outside.
Burns and injuries are caused almost invariably by picking up the burning pan to carry
outside.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Fig. 10
DESN 513710
21
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTROL PANEL
z
The GAS HOTPLATE CONTROL KNOBS can only be rotated anti-clockwise from the OFF
position.
Symbol - Ignition Setting
Large Flame Symbol - High Setting
Small Flame Symbol - Low Setting
(See ‘HOTPLATE’ section).
Fig. 11
DESN 513715
z
The GRILL ELEMENT CONTROL KNOB can be rotated in either direction.
Clockwise
Anti-clockwise
Full on, with both elements on
Economy grill, centre element only
z
z
The OVEN CONTROL KNOBS can only be rotated clockwise from the OFF position.
The OVEN NEONS illuminate when ovens are switched on. When the required
temperature is reached the neon will extinguish.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
GAS HOTPLATE
z
The hotplate has six gas burners:
front left - ultra rapid (wok) burner - rated at 4.0 kW
rear left and front centre - semi-rapid burners - each rated at 1.75 kW
rear right and front right - rapid burner - each rated at 3.0 kW
centre rear - ultra rapid burner - rated at 5.0 kW
z
The semi rapid burners are especially suited for use with small pans and gentle simmering
or poaching.
z
z
All burners have a set simmer position and are easily adjustable.
WARNING: The LPG Six-Four Series is not approved for use with a flat griddle plate.
The flat griddle plate MUST NOT be used, only use the round ribbed pan provided.
Performance and technical problems can occur when a large flat griddle plate is fitted over
LPG burners, delayed ignition of unburnt gas can occur on LPG products, especially on a
hotplate fitted with high rated burners.
TO USE THE HOTPLATE
z
To light a hotplate burner, push in and turn the control knob anti-clockwise to the large
flame symbol ( ), and hold in for 3 seconds until the burner lights, then turn the knob to
the required setting.
z
z
z
If the burner flame should accidentally go out, turn off the burner control and do not
attempt to re-light the burner for at least one minute.
The control may be set towards a lower position, simply by turning the control knob
towards the small flame symbol.
IMPORTANT: The cast iron supports on the appliance are much heavier than those on
most gas hotplate cookers, therefore care must be taken when removing or refitting them
to the hob. It is important that they are lifted from the appliance and not dragged across
adjacent enamelled components which would result in damaging the enamel.
.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
SOME SAFETY POINTS
z
z
z
Simmering aids such as asbestos or mesh mats are not recommended. They can impede
burner performance, damage the pan supports and waste fuel.
Commercially available foil spillage aids are unnecessary on this cooker and could effect
the combustion.
Some ‘Wok’ cooking pans are unstable. Check with the ‘Wok’ manufacturer before
purchasing.
z
z
z
z
Do not use unstable and misshapen pans (e.g. with convex bases) that tilt easily.
Pans and kettles with concave bases should not be used.
The minimum pan diameter recommended is 120mm.
Place all pans centrally over the burners. The flames must be on the base of the pan. Do
not allow the flames to go up the sides of the pan. (See Fig. 12).
z
z
Always position pan handles away from the front of the cooker - out of reach of small
children.
NEVER leave a chip pan unattended.
NOTE
Aluminium pans may cause a metallic marking on the pan supports. This will not affect the
durability of the enamel. The appliance warranty does not cover mis-use of the pan supports.
Fig. 12
DESN 512396
24
Download from Www.Somanuals.com. All Manuals Search And Download.
TO FIT PAN SUPPORTS
Fit the pan supports in the following order. The pan supports are marked on the underside to
correspond to the markings below. The pan supports must locate in the recesses in the hotplate
casting.
Fig. 13A
DESN 513712 A
Important
It is very important for the performance and reliability of the hob that the pan supports are fitted
in accordance with the AGA SIX-FOUR SERIES - DC6 OWNERS MANUAL.
To help identify the correct location of the pan supports, the centre rear pan support has been
uniquely designed with tag, as shown. This pan support must be fitted in the rear centre position
with the tag pointing towards the back of the appliance.
Fig. 13B
DESN 512995 A
25
Download from Www.Somanuals.com. All Manuals Search And Download.
SETTING UP THE COOKER FOR USE
Before you can use the lower left hand oven of the appliance it will be necessary to set the ‘time
of day’ clock.
This is a 24 hour clock, and when the power supply is initially switched on, or after an interruption
in supply, the clock will show AUTO and 0.00 alternately.
Fig. 14
SETTING THE TIME OF DAY
1.
Press and hold the MINUTE TIMER
and COOK TIME
buttons at the same time,
(the word AUTO flashes and the 0.00 is displayed steadily) press the plus + or minus -
buttons until the required time of day is displayed. The time will increase/decrease from
12.00 hours in minute intervals, slowly and then gaining speed. .
The cooker is now ready for manual use.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
SIMMERING OVEN
THE SIMMERING OVEN
This is used for long, slow cooking over 6-8 hours, keeping food warm and warming plates for
short periods.
EXTRA CARE MUST BE TAKEN WHEN WARMING BONE CHINA - USE THE LOWEST
SETTING.
The slow cooking setting is the area marked between 110ºC - 120ºC on the oven control knob.
USING THE SLOW COOKING SETTING
Points to bear in mind when preparing food.
z
Do not place dishes directly on to the oven base. Always place onto shelf supplied. See
Fig. 17B.
z
Push dishes well back in the oven to ensure that they are positioned over the element
beneath the base plate.
z
z
Make sure all dishes will fit into the oven before preparing the food.
All dishes cooked by the slow cooking method should be cooked for a minimum of 6
hours. They will ‘hold’ at this setting for a further 1-2 hours but marked deterioration in
appearance will be noticed in some cases.
z
z
Joints of meat and poultry should be cooked at 180ºC for 30 minutes before transferring
to the slow cooking oven.
Meat over 2.7kg (6lbs) and poultry over 2kg (4lbs 8ozs) are unsuitable for the slow cooking
method.
z
z
z
z
z
Always stand covered joints on a rack over a meat tin, to allow good air circulation.
Make sure that pork and poultry reach an internal temperature of at least 90ºC.
This method is unsuitable for stuffed meat and poultry.
Always bring soups, casseroles and liquids to the boil before putting in the oven.
When casseroles are used, cover the food first with foil and then the lid to prevent loss of
moisture.
z
z
z
z
Always thaw frozen food completely before cooking.
Root vegetables will cook better if cut into small pieces.
Adjust seasonings and thickenings at the end of the cooking time.
Egg and fish dishes need only 1-5 hours cooking and should be included in day cooking
sessions, where they can be observed from time to time.
z
Dried red kidney beans must be boiled for a minimum of ten minutes, after soaking, and
before inclusion in any dish.
STORAGE AND RE-HEATING OF FOOD
z
If food is to be frozen or not served immediately, cool it in a clean container as quickly as
possible.
z
z
Thaw frozen food completely in the refrigerator before re-heating.
Re-heat food thoroughly and quickly either on the hotplate or in a hot oven 180ºC, and
then serve immediately.
z
Only re-heat food once.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Simmering Oven • Simmering Oven • Simmering Oven • Simmering Oven • Simmering Oven •
Simmering Oven
IDEAS FOR THE SIMMERING OVEN
Many favourite recipes can be adapted for this type of cooking. Check that chosen ovenware will fit into the oven.
Meal 1
6 - 8 hours cooking
Ragout of Beef in Ale
Baked Potatoes
Recipes
Ragout of Beef in Ale
30ml (2tbsps) oil
1.
Sauté the meat in hot oil in a flame proof casserole dish until
brown.
Sauté the garlic, onions, carrots and mushrooms until brown.
Stir in flour and mix well.
Add mustard, sugar and tomato purée.
Stir in the ale and seasoning. Return meat.
Bring to the boil and cover. Transfer to oven.
675g (11/2 lbs) chuck steak, cubed
1 clove of garlic, crushed
2 carrots, sliced
100g (4oz) mushrooms, quartered
2 medium onions, sliced
40g (11/2 ozs) plain flour
2.
3.
4.
5.
6.
5ml (1 tsp) coarse-grained mustard
10ml (1dsp) demerara sugar
30ml (2tbsps) tomato purée
450ml (3/4 pt) brown ale
salt and freshly ground pepper
Baked Potatoes
4 medium sized potatoes
1.
2.
3.
Wash and prick well all over.
Wrap in one layer of foil.
Place directly on the shelf.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Slow Cooking Oven • Slow Cooking Oven • Slow Cooking Oven • Slow Cooking Oven • Slow Cooking Oven • Slow Cooking Oven •
Meal 2
6 - 8 hours cooking
Roast Fillet of Lamb
Dauphinoise Potatoes
Bread and Butter Pudding
Recipes
Roast fillet of Lamb
900g - 1.25 kg (2-2 1/2 lbs) lamb
1.
2.
Season and wrap the lamb in foil.
Stand meat on a rack (if possible) over a small shallow tin.
Dauphinoise Potatoes
450g (1lb) potatoes, thinly sliced
1-2 cloves of garlic, crushed
125ml (1/4 pt) double cream
1.
2.
Grease a shallow oval or rectangular dish.
Arrange layers of potatoes, seasoning and garlic in the dish, ending
with potatoes.
salt and freshly ground black pepper
3.
Pour over the cream and cover well with foil.
Bread and Butter Pudding
6-8 medium slices of wholemeal bread
Approx 50g (2ozs) butter, melted
Grated rind of one orange (optional)
25g (1oz) desiccated coconut
50 - 100g (2 - 4oz) luxury/tropical mixed fruit
50g (2oz) soft brown sugar
450ml (3/4 pt) milk
1.
2.
3.
Grease a shallow oval or rectangular dish.
Cut the crusts off the bread and divide into rectangles/triangles.
Dip enough pieces of bread in the butter on one side to cover the
base of the dish, butter side up.
Sprinkle with half of the fruit, coconut, sugar and orange rind.
Cover with a second layer of bread dipped in the butter and then
the remaining rind, fruit, coconut and sugar.
4.
5.
2 eggs
6.
Whisk the eggs and milk together and pour over the bread. Stand
for 1/2 hour before baking. Leave uncovered in the oven.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Slow Cooking Oven • Slow Cooking Oven • Slow Cooking Oven • Slow Cooking Oven • Slow Cooking Oven • Slow Cooking Oven •
Meal 3
6 - 8 hours cooking
Gammon and Apricot Pie
Braised Red Cabbage
St. Clements Pudding
Recipes
Gammon and Apricot Pie
2 gammon rashers approx 15mm (1/2”) thick
100g (4oz) no-soak dried apricots
25g (1oz) sultanas
3 large potatoes, thinly sliced
300ml (1/2 pt) chicken stock
50g (2oz) butter, melted
1.
Remove the rind from the gammon. Nick the edges and lay them
in a shallow dish.
Sprinkle with apricots, sultanas and pepper.
Overlap the sliced potatoes on top of the gammon. Pour over
stock.
2.
3.
4.
Brush with melted butter place in the oven.
Braised Red Cabbage
350g (3/4 lb) red cabbage
25g (1oz) butter
1 medium onion, sliced
1 medium cooking apple, sliced
30ml (2 tbsps) cider vinegar
45ml (3 tbsps) honey
salt and pepper
1.
2.
Slice the red cabbage finely
Melt the butter in a large saucepan and sauté the onion and apple
until starting to soften.
Add the cabbage and cook for a further 2 minutes
Mix in the vinegar, honey and seasoning.
Transfer to an ovenproof dish, and cover tightly with foil. Place in
the oven.
3.
4.
5.
St Clements Pudding
2 rounds of thick sliced wholemeal bread
a little milk
50g (2oz) butter or margarine
50g (2oz) soft brown sugar
grated rind and juice of 1 lemon
grated rind and juice of 1 orange
3 eggs, separated
1.
Grease a shallow oven-proof dish and line the base with fingers of
bread.
Pour over sufficient milk to be absorbed by the bread.
Cream the fat and sugar.
Add the yolks, lemon and orange rind and juice. Beat.
Whisk the egg whites stiffly and fold most of them into the
creamed mixture.
2.
3.
4.
5.
caster sugar for sprinkling
6.
7.
Spread this mixture over the bread.
Finish with a layer of the remaining egg white, thickly dredged with
sugar. Leave uncovered. Place in the oven.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Slow Cooking Oven • Slow Cooking Oven • Slow Cooking Oven • Slow Cooking Oven • Slow Cooking Oven • Slow Cooking Oven •
Meal 4
Chilli Con Carne
Frangipane and Apple Pudding
Recipes
Chilli Con Carne
450g (1lb) minced beef
1.
2.
3.
4.
Brown the minced beef in a flame proof casserole dish.
Stir in the spice mix.
Add beans drained, tomatoes and water.
Mix well together. Bring to boil, cover well and place in oven.
1 x 400g (14oz) tin tomatoes
1 x 400g (14oz) tin kidney beans
1 packet Chilli con carne spice mix
100ml (4 fl oz) water
Frangipane and Apple Pudding
450g (1lb) cooking apples, grated
50g (2oz) vanilla fudge, chopped
50g (2oz) softened butter
50g (2oz) soft brown sugar
50g (2oz) ground almonds
12g (1/2 oz) plain flour
1 egg
1.
2.
3.
Grease a shallow oven dish.
Mix the apples and fudge together and place into the dish.
Cream the rest of the ingredients and add a few drops of almond
essence.
Carefully spread over the apple. Leave uncovered and place in
oven.
4.
almond essence
31
Download from Www.Somanuals.com. All Manuals Search And Download.
THE GRILL
z
z
THE GRILL COMPARTMENT DOOR MUST BE KEPT OPEN WHEN THE GRILL IS ON.
CAUTION: Accessible parts may be hot when the grill is in use. Young children
should be kept away.
z
z
The very high speed instant grill is divided into two areas to save energy and to suit
individual grilling requirements.
Turn the grill control clockwise and the whole of the grilling area can be used for large
amounts of food. Turn the control anti-clockwise and the middle area only can be used for
small amounts e.g. 2 slices of bread, one or two chops etc.
z
Most food is cooked at a high setting but for thicker pieces of meat/poultry and for food
such as well done steak the heat can be reduced by turning the control down to a lower
setting.
z
z
For best results pre-heat at a high setting for approximately 2 minutes.
The grill pan fits on the shelf supplied. The shelf is designed to lock in place, but is
removable for cleaning. See Fig. 17B .
z
Food should be cooked on the grid or in the base of the grill pan. Some dishes can be
placed straight onto the shelf or floor of the compartment. This is useful when browning
the top of food such as cauliflower cheese.
z
z
The oven side panels are self cleaning.
The grill pan can be stored in the base of the grill compartment, when the grill is off.
The following information is for guidance only as shape, thickness, size of food and personal
taste can vary.
FOOD
SUGGESTED HEAT SETTING
Toast
HIGH
HIGH
HIGH
Pikelet/Crumpet/Muffins
Bacon
Sausage
Beefburger
Steak med./rare
Chops
Fish - whole
- steaks
HIGH TO MED.
MED. as per packet instructions
HIGH TO MED.
HIGH TO MED.
HIGH TO MED.
HIGH TO MED.
HIGH
- fillets
Chicken portions
Toppings i.e. meringue,
potato, cheese etc.
HIGH TO MED.
HIGH
32
Download from Www.Somanuals.com. All Manuals Search And Download.
THE OVENS
General
z
The ovens and grill compartment are fitted with side and back self cleaning panels. The
roof of the oven is also self-cleaning enamel.
z
z
The shelves are designed to be non-tilt.
To remove a shelf, lift clear of the side notches and slide forward. To replace a shelf, insert
into the oven with the short prongs at the rear, facing upwards. Slide into position above
the side notches then allow to drop down on the runner.
z
z
z
Do not place the grid shelf or food on the bases of the ovens.
Pre-heat the ovens at the appropriate settings until the neon light goes out.
For effective heat distribution, leave a gap of no less than 12mm between the dishes and
the sides of the oven.
z
Do not use a tray or tin greater than 30cm x 24cm (12 hole bun tin or swiss roll tray).
Condensation
Condensation may form on the cooker. This is quite normal and nothing to worry about. The
condensation forms when heat and moisture are present, for example during cooking. Whenever
possible try to make sure that the food which contains a lot of moisture for example casseroles
are covered. If you do notice any condensation, wipe it up straight away.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
OVEN COOKING GUIDE
Cooking Hints
z
z
z
Shelf positions are counted from the bottom.
Put dishes in the centre of the shelf.
When using the fan oven, reduce conventional oven settings by 10ºC - 20ºC and in some
cases, cooking time by up to 10 minutes for every hour.
z
z
It is important to check that food is piping hot before serving.
You can change the setting and cooking times to suit your tastes.
Deep Fat Frying
z
Do not try to fry too much food at a time, especially frozen food.
This only lowers the temperature of the oil or fat too much, resulting in greasy food.
z
Always dry food thoroughly before frying and lower it slowly into the hot oil or fat. Frozen
foods in particular, will cause frothing and spitting, if added too quickly.
z
z
z
Never heat fat, or fry with a lid on the pan.
Keep the outside of the pan, clean and free from streaks of oil or fat.
The following chart gives a guide to cooking a number of every day items.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Conventional Oven
Conventional Oven • Conventional Oven • Conventional Oven • Conventional Oven
z
The right hand upper oven is a conventional oven which means that the heating elements are in the top and under
the base of the oven compartment.
z
z
The cooking charts are a general guide but times and temperatures may vary according to individual recipes.
The meat sections should be used as a general guide but may vary according to the size, shape of joint on or off the
bone.
z
z
z
Thaw frozen joints before cooking them.
The times are for open roasting. If covered allow for extra time.
The turkey/chicken is cooked when the juices run clear when pierced with a skewer. If the juices are still pink
continue to cook, checking every 15 minutes.
z
Shelves are numbered from the bottom upwards.
SHELF
POSITION
APPROXIMATE COOKING TIME & COMMENTS
FOOD
Fish
SETTING °C
Whole Fish e.g. trout, mackerel
Steaks
190
2 or 3
2 or 3
3 or 4
1 or 2
25 - 30 mins depending on size
20 - 25 mins depending on thickness
25 mins depending on packet instructions
15 - 18 mins per 450g
190
Oven-fried fish
Salmon (2.7kg)
Meat & Poultry
Beef
210 - 220
160 - 170
180 - 190
180 - 190
180 - 190
190 - 200
180 - 190
190 - 200
150 - 160
1 or 2
1 or 2
1 or 2
1 or 2
1
30 mins per 450g + 30 mins over (medium rare)
25 mins per 450g + 25 mins over
Lamb
Pork
30 - 35 mins per 450g + 35 mins over
20 - 25 mins per 450g + 20 mins over
15 - 18 mins per 450g + 15 mins over
Chicken
Turkey
Duck & Goose
Casserole
1
25 mins per lb + 25 mins over
1
1 or 2
2
1 / - 3 hours depending on recipe
Puddings
Milk Puddings
Baked Custard
Baked Sponge Pudding
Fruit Crumble
160
150
1 or 2
1 or 2
2 or 3
2 or 3
2 hours
35 mins
190
45 mins - 1 hour using raw fruit
45 mins - 1 hour
190 - 200
35
Download from Www.Somanuals.com. All Manuals Search And Download.
• Conventional Oven • Conventional Oven • Conventional Oven • Conventional Oven • Conventional Oven • Conventional Oven •
SHELF
POSITION
APPROXIMATE COOKING TIME
FOOD
SETTING °C
Meringue Toppings
Meringues
140 - 150
100 - 110
1 or 2
2
45 mins
3 - 4 hours - Turn meringues over as soon as they are set
Yeast Mixture
Bread - loaves
Bread - rolls
220 - 230
220 - 230
190
1
30 - 45 mins
15 - 20 mins
25 - 35 mins
2 or 3
1 or 2
Chelsea Buns etc
Cakes, Pastries, Biscuits &
Scones
Small Cakes
190
180
3
20 - 25 mins
Victoria Sandwich
Swiss Roll
3
25 - 30 mins
190
2 or 3
3
7 - 10 mins
Fatless Sponge (180mm)
Scones
190
20 mins
10 - 15 mins
220
3
Maderia Cake
180
1 or 2
1
1 hour - Place on a piece of citron peel after 20 mins
2 - 2 1/2 hours
Med. Rich Fruit Cake
Christmas Cake
Gingerbread
150
1
140 - 150
150 - 160
150
1
4 - 4 /2 hours
1 - 1 1/2 hours
1 1/4 - 1 1/2 hours
1 or 2
2 or 3
2 or 3
2 or 3
2 or 3
2 or 3
2 or 3
2 or 3
Shortbread
Biscuits
170 - 180
180 - 190
200
15 - 25 mins depending on recipe
30 mins - 1 1/2 hours depending on recipe
Tray Bakes & Tea Breads
Shortcrust Pastry
Rich Shortcrust
Flaky/Puff Pastry
Choux Pastry
Small Tarts 20 - 25 mins depending on recipe, Pies 45 - 50 mins depending on recipe
190
25 mins
8 - 10 mins depending on recipe
25 - 35 mins
220 - 230
200
Miscellaneous
Yorkshire Pudding - Large
Yorkshire Pudding - Individual
Soufflés
220
220
190
2 or 3
2 or 3
2
45 mins
20 - 25 mins
45 mins
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Fan Oven
• Fan Oven • Fan Oven • Fan Oven • Fan Oven • Fan Oven • Fan Oven • Fan Oven •
z
The left hand lower oven is a fan oven, which means that the air is circulated to create an even temperature
throughout. In most cases food requires a lower oven temperature when cooked in ovens by approximately 10ºÞC -
20ºC.
z
z
z
z
z
The cooking charts are a general guide but times and temperatures may vary according to individual recipes.
The meat sections should be used as a guide but may vary according to the size, shape of joint on or off the bone.
Thaw frozen joints thoroughly before cooking them.
The times are for open roasting. If covered with foil allow for extra time..
The turkey/chicken is cooked when the juices run clear when pierced with a skewer. If the juices are still pink
continue to cook checking every 15 minutes until juices run clear.
APPROXIMATE COOKING TIME
FOOD
Fish
SETTING °C
Whole Fish e.g. trout, mackerel
Steaks
170
170
25 - 30 mins depending on size
20 - 25 mins depending on thickness
25 mins depending on packet instructions
15 - 18 mins per 450g
170
Oven-fried fish
Salmon (2.7kg)
140 - 150
Meat & Poultry
Beef
170 - 180
170 - 180
170 - 180
170 - 180
150 - 160
170 - 180
130 - 140
30 mins per 450g + 30 mins over (medium rare)
25 mins per 450g + 25 mins over
Lamb
Pork
30 - 35 mins per 450g + 35 mins over
20 - 25 mins per 450g + 20 mins over
15 - 18 mins per 450g + 15 mins over
25 mins per lb + 25 mins over
Chicken
Turkey
Duck & Goose
Casserole
1 1/2 - 3 hours depending on recipe
Puddings
Milk Puddings
Baked Custard
Baked Sponge Pudding
Fruit Crumble
140
140
2 hours
35 mins
160
45 mins - 1 hour using raw fruit
45 mins - 1 hour
170 - 180
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Fan Oven • Fan Oven • Fan Oven • Fan Oven • Fan Oven • Fan Oven • Fan Oven • Fan Oven • Fan Oven • Fan Oven •
APPROXIMATE COOKING TIME
FOOD
SETTING °C
Meringue Toppings
Meringues
130
45 mins
80 - 90
3 - 4 hours - Turn meringues over as soon as they are set
Yeast Mixtures
Bread - loaves
Bread - rolls
200 - 210
200 - 210
180
30 - 45 mins
15 - 20 mins
25 - 35 mins
Chelsea Buns etc.
Cakes, Pastries, Biscuits &
Scones
Small Cakes
170 - 180
160 - 170
200 - 210
170
20 - 25 mins
Victoria Sandwich
Swiss Roll
25 - 30 mins
7 - 10 mins
Fatless Sponge (180mm)
Scones
20 mins
200 - 210
160
10 - 15 mins
Maderia Cake
1 hour - Place on a piece of citron peel after 20 mins
2 - 2 1/2 hours
Med. Rich Fruit Cake
Christmas Cake (205mm)
Gingerbread
130
4 - 4 1/2 hours
130
1 - 1 1/2 hours
1 1/4 - 1 1/2 hours
130 - 140
140 - 150
130 - 180
160 - 170
190
Shortbread
Biscuits
15 - 25 mins depending on recipe
30 mins - 1 1/2 hours depending on recipe
Small Tarts 20 - 25 mins depending on recipe, Pies 45 - 50 mins depending on recipe
25 mins
Tray Bakes & Tea Breads
Shortcrust Pastry
Rich Shortcrust
Flaky/Puff Pastry
Choux Pastry
180
210
8 - 10 mins depending on recipe
25 - 35 mins
190 - 200
Miscellaneous
Yorkshire Pudding - large
Yorkshire Pudding - individual
Soufflès
200
200
45 mins
20 - 25 mins
45 mins
170 - 180
38
Download from Www.Somanuals.com. All Manuals Search And Download.
THE MINUTE TIMER
The minute timer works separately from the time of day clock and can be set to time periods from
1 minute to 23:59 hours. Only a one handed operation is required.
SETTING THE MINUTE TIMER
1. Press the MINUTE TIMER
button the bell symbol and 0.00 will be displayed. Set the
required time by using the plus + and minus - buttons.
2. After 5 seconds the display will go back to showing the time of day, the bell symbol will
remain steady and the set time will immediately start to count down, by pressing the
minute timer button, the display will show the time remaining.
3. At the end of the set time, a beep will sound, the bell symbol will flash and continue for 2
minutes unless cancelled by pressing the MINUTE TIMER
button or MANUAL
button.
4. The setting can be cancelled by pressing the MINUTE TIMER
running the time back to 0.00.
and minus - buttons and
FIG. 15
DESN 512657
39
Download from Www.Somanuals.com. All Manuals Search And Download.
AUTOMATIC COOKING CONTROL
This can be used to set an automatic cooking programme in the bottom left fan oven only. It
switches the electricity on or off at the pre-set times.
The maximum length of cooking programme which can be set is 23 hours and 59 minutes e.g.
delay time + cooking time = maximum 23 hours and 59 minutes.
Before setting a programme check that the clock is telling the correct time of day, and have the
following information to hand:
z
z
z
The length of time the food needs to cook.
The time that the food is to finish cooking.
The oven control setting required.
SETTING THE AUTOMATIC COOKING PROGRAMME
Either the STOP TIME or the COOK TIME buttons can be pressed first.
Each setting will remain displayed for 5 seconds before changing back to display the time of day.
An example of setting a programme using the cook time button first.
The food needs 2 hours and 30 minutes at 140ºC and is required to be ready by 18.00 hours.
1.
2.
3.
Place the food on the correct shelves in the oven.
Check that the clock is telling the correct time of day.
Press the COOK TIME
button and then the plus + or minus - buttons until 2 hours 30
minutes is displayed.
4.
Press the STOP
displayed.
button and then the plus + or minus - buttons until 18.00 hours is
5.
6.
7.
Set the oven temperature control to 140ºC.
5 seconds after setting, the clock will display the time of day and AUTO.
When cooking starts the COOK TIME
symbol illuminates and remains throughout
cooking.
8.
When the cooking has finished, a beep will sound and continue for 2 minutes, unless
cancelled manually.
The AUTO symbol will flash. To cancel these and return to manual press MANUAL COOK
button twice.
SETTING AN END TIME ONLY , AUTOMATICALLY
1. Place the food on the correct shelves in the oven.
2. Press the STOP
button until the time at which cooking is to end, appears on the display.
3. Set the oven temperature control.
Cooking will start immediately and the COOK TIME
throughout cooking.
symbol will illuminates and remain
4. When the cooking is finished, a bleep will sound and continue for 2 minutes unless cancelled
manually.
The AUTO symbol will flash.
5. To cancel and return to manual mode, press the MANUAL COOK TIME
twice.
Programmes can be adjusted at any time by pressing the appropriate buttons and the plus + and
minus - buttons as described previously.
CANCELLING A PROGRAMME
The cooking programme can be cancelled by pressing the COOK TIME
- buttons until 0.00 appears in the display.
button and the minus
Press the MANUAL COOK TIME
button to return the oven to manual mode.
NOTE: When an automatic cooking programme has been set, the time of day clock cannot be
adjusted.
40
Download from Www.Somanuals.com. All Manuals Search And Download.
KEY LOCK - If this mode is activated, a program can be set but it will not be activated, i.e. ON
and OFF times can be set, but timer will not switch the ovens on.
TO ACTIVATE KEY LOCK FUNCTION
1.
2.
Ensure the timer is in manual mode (no active programs).
Hold the MINUTE TIMER button and COOK TIME
approximately 8 seconds. The display will read ON.
button simultaneously for
3.
Press the + plus button. The display reads OFF and the key symbol appears. After
approximately 5 seconds the time of day reappears next to the key symbol. The key lock
is now activated.
TO DEACTIVATE KEY LOCK FUNCTION
1.
2.
Ensure the timer is in manual mode.
Hold the MINUTE TIMER
button and COOK TIME
button simultaneously for
approximately 8 seconds, the display will read OFF.
3.
Press the + plus button. The display reads ON, the key symbol disappears. After
approximately 5 seconds the time reappears and the key lock is now deactivated.
41
Download from Www.Somanuals.com. All Manuals Search And Download.
CLEANING & CARING FOR YOUR COOKER
General
z
z
z
z
z
z
Always switch OFF at the mains before cleaning.
Use as little water as possible.
Do not use CAUSTIC CLEANING SOLUTIONS
Do not use a steam cleaner to clean this cooker.
Wipe up any spills as they occur and transfer pans to other burners to continue cooking.
TAKE CARE NOT TO DAMAGE THE OVEN THERMOSTAT PHIAL OR THE HOTPLATE
IGNITION ELECTRODES DURING CLEANING.
z
z
z
After cleaning, ensure all parts are thoroughly dry before replacing.
When re-fitting the burner caps and burner heads make sure that they are properly located.
THE FOLLOWING PARTS ARE NOT DISHWASHER SAFE:
Aluminium burner heads (LHR, CF, RHR, RHF).
IMPORTANT: Aga recommend Vitreous Enamel Association approved cleaners for
cleaning the vitreous enamelled surfaces of this product.
But they are unsuitable for use on: chrome and stainless steel components, handrails and
their brackets.
THE COOKER CANNOT BE MOVED ONCE INSTALLED.
DO NOT ATTEMPT TO MOVE THE COOKER BY PULLING THE HANDRAIL OR DOORS.
42
Download from Www.Somanuals.com. All Manuals Search And Download.
CLEANING & CARING FOR YOUR COOKER
COOKER PART AND FINISH
CLEANING METHOD
Vitreous Enamel
Clean with a damp cloth and hot soapy
water. Stubborn stains can be removed with
mild cream, paste or liquid cleaners, or by
gently rubbing with a well moistened,
liberally soaped very fine steel wool pads
e.g. Brillo.
Grill - base only
Hotplate
Control panel
Pan supports
Roasting tin
Grill pan
Conventional, fan and simmering oven -
The pan supports, roasting tin and baking
tray may OCCASIONALLY be cleaned in a
dishwasher.
base only
Door liners
Front of cooker
Doors
z
Check that the cleaning agent is
approved by the (VEA) Vitreous Enamel
Association.
High Temperature Protective Coating
Clean with a damp cloth and hot soapy
water.
Hand rail bracket
Burner caps
Burner heads
Plinth
IMPORTANT:
DO NOT USE ABRASIVES
Glass
As for enamel cleaning above. Polish with a
clean dry cloth or kitchen roll.
Grill element cover
Splashback
Stainless Steel
Use warm soapy water or a proprietary
stainless steel or chrome cleaner.
Door catches
Handrail
Chromium Plated
Wipe with a damp cloth and soapy water.
A well moistened liberally soaped very fine
steel wool pad e.g. Brillo, or stainless steel
cleaner may be used.
Oven and grill shelves
Shelf supports
Grill pan handle
Grill pan grid
Plastic
Wipe with a damp cloth and hot soapy water.
Stubborn stains may be removed with a
cream cleaner carefully applied.
Grill pan handle
Control knobs
Timer facia & controls
Neons
43
Download from Www.Somanuals.com. All Manuals Search And Download.
COOKER PART AND FINISH
Self-Clean Enamel
CLEANING METHOD
This special enamel has a continuous
cleaning action, which works best if a pattern
of low and high temperature cooking is
followed. By using low temperature roasting,
excessive fat splashes can be avoided.
Should any excessive staining occur,
immediately clean the area with hot water
containing detergent, and a nylon washing-
up brush. Resistant stains require the oven
to be run at 210°C for 2 hours.
Fan Oven, Conventional Oven, Simmering
Oven: sides, top and back
Grill Compartment: sides and back
DO
NOT
USE
ANY
CLEANING
MATERIALS WHICH MAY CLOG THE
PORES OF THE SPECIAL COATING e.g.
PASTES AND POWDERS, SOAP-FILLED
PADS, WIRE WOOL, SPRAY CLEANERS,
BRUSH-ON OVEN CLEANERS, CAUSTIC
SOLUTIONS, METAL SCRAPERS/KNIVES,
AND PREVENT THE CONTINUOUS
CLEANING ACTION.
Aluminium
As for enamel cleaning. Do not place in a
dishwasher
Right & left rear outer burner caps
Right front outer burner cap
Centre front outer burner cap
NOTE: Care must be taken to prevent
cleaning materials, water or dirt, from
entering and blocking the burner head, ports
and especially the gasway. Remove any
blockage with a fine needle or nylon brush.
Non-Stick Coating
Soak and wash in hot soapy water.
Griddle plate
DO NOT USE ABRASIVES OR PLACE IN A
DISHWASHER.
FIG. 16
DESN 512935 A
44
Download from Www.Somanuals.com. All Manuals Search And Download.
Oven Shelves - These shelves are designed to slide out
STOP ON SHELF
MUST PROJECT
UPWARDS
SHELF STOP AND
ANTI TILT BRACKET
DESN 511867
Refit as follows:
Locate in guide as above.
DESN 511866
Please Note: Shelf slides out to stop position.
Fig. 17A
Grill Shelf - operates as oven shelves
DESN 512411
Fig. 17B
45
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY OF RAPID AND SEMI-RAPID BURNER
BURNER CAP
BURNER HEAD
ELECTRODE
Fig. 18
DESN 511618
FITTING BURNER CAP - RAPID AND SEMI-RAPID
BURNER
BURNER CAP
RETAINING LUGS
Fig. 19
DESN 511617
46
Download from Www.Somanuals.com. All Manuals Search And Download.
WOK BURNER
Fig. 20A
DESN 513512
ULTRA RAPID BURNER
Fig. 20B
DESN 513714
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Servicing
Section
Remember, when replacing a part on this appliance, use only spare parts that you can be
assured conform to the safety and performance specification that we require. Do not use
reconditioned or copy parts that have not been clearly authorised by Aga.
48
Download from Www.Somanuals.com. All Manuals Search And Download.
SERVICING
z
z
In the event of your appliance requiring maintenance, please call Aga Service or contact
your authorised distributor/stockist.
Your cooker must only be serviced by a Qualified CORGI Engineer from an Authorised
Distributor or Stockist.
z
z
Do not alter or modify the cooker.
Only the spares specified by the manufacturer are to be fitted.
49
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING: WHEN SERVICING OR REPLACING GAS CARRYING COMPONENTS,
DISCONNECT GAS SUPPLY TO APPLIANCE AND AFTER COMPLETION CHECK
APPLIANCE FOR GAS SOUNDNESS.
WARNING: WHEN SERVICING OR REPLACING COMPONENTS, ISOLATE THE
APPLIANCE FROM THE ELECTRIC SUPPLY AND BEFORE RECONNECTING, CHECK FOR
ELECTRICAL SUPPLY.
A. TO REMOVE HOTPLATE
1.
2.
3.
4.
5.
Isolate from electric supply.
Remove pans supports and burner caps. (See Fig. 21).
Remove burner fixing screws (14) and hotplate fixing nuts (8).
Lift off burner fixing rings (6).
Lift off hotplate castings in the following order: left hand, right hand and centre. (See Fig.
22).
NOTE: Each hotplate casting has an earth lead. Each lead must be disconnected before
completely removing hotplate casting. (See Fig. 23).
Re-assemble in reverse order.
6.
Fig. 21
DESN 512935 A
Fig. 22
DESN 512393 C
50
Download from Www.Somanuals.com. All Manuals Search And Download.
Fig. 23
DESN 512407 B
B. TO REMOVE SIDE PANELS
1.
2.
Isolate from electric supply.
Lower the cooker onto the rollers by turning the adjusting feet fully anti-clockwise.
NOTE: It may be necessary to disconnect the flexible gas connection to allow the cooker
to be withdrawn from between the kitchen units.
3.
4.
5.
Roll the cooker slightly forward, unhook the safety chain and disconnect the flexible hose.
Remove rear fixing screws (3) and slide side panel back and out.
Re-assemble in reverse order.
C. TO REMOVE FACIA CASTINGS
1.
2.
3.
4.
Isolate from electric supply.
Proceed as ‘TO REMOVE HOTPLATE CASTINGS’.
Pull off control knobs.
Remove control panel fixing screws (4 per casting) (See Fig. 24). When removing the
screws support the casting.
NOTE: When removing the castings, the oven indicator neons require disconnecting from
the facia, hold the cables at their entry into the neon twist and pull, this will disengage the
neon assembly. Be careful when refitting facia castings to position neon and wires
correctly,
DESN 512400 A
Fig. 24
51
Download from Www.Somanuals.com. All Manuals Search And Download.
D. TO REMOVE HANDRAIL (SEE FIG. 24)
1.
2.
Loosen 2 grub screws, one at each end of hand rail (see fig. 24) using 2 1/2 mm socket key.
Slide handrail forwards, off locating studs.
E. TO REMOVE TIMER
1.
2.
3.
4.
Isolate from electric supply.
Proceed as ‘TO REMOVE HOTPLATE CASTINGS’.
Remove fixing screws (4). Two top rear and two lower front of timer housing.
The timer assembly can now be lifted upwards sufficiently to disconnect electric cables at
rear of timer. (See Fig. 25).
NOTE: Take care to identify cable connections.
Slacken timer fixing screw sufficiently to allow timer securing strip to slide out of facia
panel. (See Fig. 25).
5.
6.
7.
Remove timer clamping screw, withdraw clamp and lift out timer. (See Fig. 26).
Re-assemble in reverse order.
Fig. 25
DESN 512401
Fig. 26
DESN 512402
52
Download from Www.Somanuals.com. All Manuals Search And Download.
E. TO REMOVE GAS TAPS/IGNITION SWITCHES
1.
2.
3.
4.
5.
6.
7.
8.
9.
Isolate from electric and gas supply.
Proceed as ‘TO REMOVE HOTPLATE’.
Proceed as ‘TO REMOVE FACIA’.
Disconnect gas rail feed pipe (19mm nut). (See Fig. 27).
Disconnect all gas connections to taps (5 nuts - 13mm, 14mm and 19mm).
Remove (4) screws fixing gas rail.
Disconnect ignition switch.
Lift complete gas rail assembly clear of appliance.
Remove bolt (1) and clamp fixing to gas rail and withdraw tap from gas rail.
10. Re-assemble in reverse order.
Fig. 27
DESN 513527
Fig. 27A
DESN 513711
53
Download from Www.Somanuals.com. All Manuals Search And Download.
F.
TO REMOVE GRILL REGULATOR
1.
2.
3.
4.
5.
Isolate from electric supply.
Proceed as ‘TO REMOVE FACIA CASTINGS’.
Remove two screws securing control to control mounting panel.
Withdraw control and cables taking care not to strain the cables.
Disconnect cables from the control.
NOTE: Take care to identify terminations.
Re-assemble in reverse order.
6.
G. TO REMOVE OVEN THERMOSTATS
1.
2.
3.
4.
5.
Isolate from electric supply.
Proceed as ‘TO REMOVE GRILL REGULATOR’.
Remove (7) back panel screws.
Remove thermostat phial and capillary through back of cooker, note correct capillary route.
Re-assemble in reverse order.
H. TO REMOVE SPARK GENERATOR
1.
2.
3.
4.
5.
6.
7.
8.
Isolate from electric supply.
Proceed as ‘TO REMOVE HOTPLATE CASTINGS’. Remove right hand casting only.
Slacken electric panel fixing screws (2). (See Fig. 28).
Lift panel off screws via keyhole slots.
Lift panel clear of appliance.
Disconnect electric cables to generator.
Disconnect electrode cables.
Slacken two screws securing generator to electrics panel to cooker frame and carefully
withdraw generator.
9.
Re-assemble in reverse order.
Fig. 28
DESN 513311 A
54
Download from Www.Somanuals.com. All Manuals Search And Download.
I.
TO REMOVE ELECTRODES (LHR, CF, CR, RHR, RHF BURNERS)
1.
2.
3.
Isolate from electric supply.
Proceed as ‘TO REMOVE THE HOTPLATE’.
Proceed as ‘TO REMOVE SPARK GENERATOR’ disconnect the appropriate electrode
lead.
4.
5.
Withdraw clip securing electrode to burner and withdraw lead and electrode (See Fig. 29).
Re-assemble in reverse order.
Fig. 29
DESN 513541
Fig. 29A
DESN 513713
J.
TO REMOVE ELECTRODES (LHF BURNER)
1.
2.
3.
4.
Isolate from electrical supply.
Proceed as ‘TO REMOVE HOTPLATE’.
Proceed as ‘TO REMOVE SPARK GENERATOR’.
Disconnect the left hand burner pipe (13mm) and the inner burner pipe (13mm) using the
special spanner.
5.
6.
7.
Remove the burner and burner fixing plate, by unscrewing the (4) screws holding the
burner mounting plate in place.
Turn burner over and remove electrode fixing clip. Withdraw electrode through top of
burner checking on route of lead.
Re-assemble in reverse order, re-routing lead along the same path.
55
Download from Www.Somanuals.com. All Manuals Search And Download.
Fig. 30
DESN 513530
K. TO REMOVE THERMOCOUPLE (LHF BURNER)
1.
2.
3.
4.
5.
Isolate from electric supply.
Proceed as ‘TO REMOVE HOTPLATE’.
Undo the nut fixing the thermocouple in place.
Push the thermocouple down and pull out from under the burner.
Disconnect the other end of the thermocouple cable from the gas valve. This is a push on
jack connector.
6.
Re-assemble in reverse order.
DESN 513532
Fig. 31
56
Download from Www.Somanuals.com. All Manuals Search And Download.
L.
TO REMOVE THERMOCOUPLE (LHR, RHR AND RHF BURNERS)
1.
2.
3.
4.
5.
Isolate from electric supply.
Proceed as ‘TO REMOVE THE HOTPLATE’.
Undo the nut fixing the thermocouple in place.
Push the thermocouple down and slide to the side to remove from the burner.
Disconnect the other end of the thermcouple cable from the gas valve, this is a push on
electrical terminal.
6.
Re-assemble in reverse order.
Fig. 32
DESN 513531
M. TO REMOVE OVEN AND GRILL LINERS - SEE FIG. 33
1.
2.
Remove LH and RH runners (4 screws per runner).
Remove runners and liners.
Fig. 33
DESN 512415
57
Download from Www.Somanuals.com. All Manuals Search And Download.
N. TO REMOVE ELEMENTS (RH OVENS)
1.
2.
3.
4.
5.
Isolate from electrical supply.
Proceed as ‘TO REMOVE OVEN AND GRILL LINERS’.
Remove oven base panel (1) screw at the rear of the oven.
Lift out base panel.
Remove oven element fixing screws (2) at the rear of the oven and flex elements to
remove from location bracket, pull forwards to expose terminal connections.
Remove connection, make sure they do not fall down the back of the appliance.
NOTE: RH TOP OVEN has an element above the roof liner, remove in same way as for
base elements.
6.
7.
Re-assemble in reverse order.
O. TO REMOVE FAN OVEN ELEMENT
1.
2.
Isolate from electric supply.
Proceed as ‘TO REMOVE OVEN LINERS’.
NOTE: You will only need to remove one side.
Remove (4) fan cover fixing screws and withdraw panel.
Remove 3 screws securing element to frame and carefully withdraw element until access
can be made to the electrical terminals.
3.
4.
5.
6.
P.
Disconnect terminals taking care not to allow the cable to fall down the rear of the
appliance.
Re-assemble in reverse order.
TO REMOVE OVEN FAN
1.
2.
3.
4.
Isolate from electric supply.
Proceed as ‘TO REMOVE OVEN ELEMENT’.
Remove 4 fixing screws securing fan assembly to frame.
Withdraw fan assembly sufficiently to gain access to motor electrical terminals and
disconnect cables.
5.
Remove fan blade.
NOTE: Fan blade fixing nuts is LH thread.
Remove motor from mounting plate screws.
Re-assemble in reverse order.
6.
7.
58
Download from Www.Somanuals.com. All Manuals Search And Download.
WIRING DIAGRAM - AGA DC6
59
Download from Www.Somanuals.com. All Manuals Search And Download.
For further advice or information please
contact your local distributor/stockist
With Aga’s policy of continuous product
improvement, the Company reserves the right to
change specifications and make modifications to
the appliance described at any time.
Manufactured by
Aga
Station Road
Ketley Telford
Shropshire TF1 5AQ
England
60
Download from Www.Somanuals.com. All Manuals Search And Download.
|
ADT Security Services Automobile Alarm FOCUS 200 PLUS User Manual
AEG Freezer A62000GNW0 User Manual
Aiphone Marine Radio NE NVP RA User Manual
Airpura Industries Air Cleaner T600 User Manual
Alliance Laundry Systems Clothes Dryer Stacked Drying Tumbler User Manual
Aluratek Computer Drive ACUES3501000F User Manual
American Audio Speaker XSP Series User Manual
Avet Reels Fishing Equipment JX 80 User Manual
Axis Communications Security Camera Q1635 User Manual
Axor Plumbing Product 10820001 User Manual