Portable Projector
LT35/LT30/LT25
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Information
Safety Cautions
Precautions
Please read this manual carefully before using your NEC LT35/LT30/LT25 projector and keep the manual handy for
future reference.Your serial number is located on the bottom of your projector. Record it here:
CAUTION
To turn off main power, be sure to remove the plug from power outlet.
The power outlet socket should be installed as near to the equipment as possible, and should be easily
accessible.
CAUTION
TO PREVENT SHOCK, DO NOT OPEN THE CABINET.
THERE ARE HIGH-VOLTAGE COMPONENTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
This symbol warns the user that uninsulated voltage within the unit may be sufficient to cause electrical
shock. Therefore, it is dangerous to make any kind of contact with any part inside of the unit.
This symbol alerts the user that important information concerning the operation and maintenance of this
unit has been provided.
The information should be read carefully to avoid problems.
WARNING: TO PREVENT FIRE OR SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.
DO NOT USETHIS UNIT’S PLUG WITH AN EXTENSION CORD OR IN AN OUTLET UNLESS ALLTHE PRONGS
CAN BE FULLY INSERTED.
DOC Compliance Notice (for Canada only)
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.
Acoustic Noise Information Ordinance-3. GSGV (for Germany only):
The sound pressure level is less than 70 dB (A) according to ISO 3744 or ISO 7779.
Disposing of your used product
EU-wide legislation as implemented in each Member State requires that used electrical and electronic
products carrying the mark (left) must be disposed of separately from normal household waste. This
includes projectors and their electrical accessories or lamps.When you dispose of such products, please
follow the guidance of your local authority and/or ask the shop where you purchased the product.
After collecting the used products, they are reused and recycled in a proper way. This effort will help us
reduce the wastes as well as the negative impact such as mercury contained in a lamp to the human
health and the environment at the minimum level.
The mark on the electrical and electronic products only applies to the current European Union Member
States.
WARNING TO CALIFORNIA RESIDENTS:
Handling the cables supplied with this product, will expose you to lead, a chemical known to the State of California
to cause birth defects or other reproductive harm. Wash hands after handling.
i
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Information
RF Interference (for USA only)
WARNING
The Federal Communications Commission does not allow any modifications or changes to the unit EXCEPT those
specified by NEC Solutions (America), Inc. in this manual. Failure to comply with this government regulation could
void your right to operate this equipment.This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates, uses, and can radi-
ate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a particular
installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio / TV technician for help.
For UK only: In UK, a BS approved power cable with moulded plug has a Black (five Amps) fuse installed for use with
this equipment. If a power cable is not supplied with this equipment please contact your supplier.
Important Safeguards
These safety instructions are to ensure the long life of your projector and to prevent fire and shock. Please read them
carefully and heed all warnings.
Installation
• Do not place the projector in the following conditions:
- on an unstable cart, stand, or table.
- near water, baths or damp rooms.
- in direct sunlight, near heaters or heat radiating appliances.
- in a dusty, smoky or steamy environment.
- on a sheet of paper or cloth, rugs or carpets.
• If you wish to have the projector installed on the ceiling:
- Do not attempt to install the projector yourself.
- The projector must be installed by qualified technicians in order to ensure proper operation and reduce the
risk of bodily injury.
- In addition, the ceiling must be strong enough to support the projector and the installation must be in accor-
dance with any local building codes.
- Please consult your dealer for more information.
Place the projector in a horizontal position
The tilt angle of the projector should not exceed 10 degrees, nor should the projector be installed in any way other than
the desktop and ceiling mount, otherwise lamp life could decrease dramatically.
10˚
ii
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Information
Fire and Shock Precautions
• Ensure that there is sufficient ventilation and that vents are unobstructed to prevent the build-up of heat inside your
projector. Allow at least 4 inches (10cm) of space between your projector and a wall.
• Do not try to touch the ventilation outlet on the right front (when seen from the front) as it can become heated while
the projector is turned on and immediately after the projector is turned off.
• Prevent foreign objects such as paper clips and bits of paper from falling into your projector. Do not attempt to
retrieve any objects that might fall into your projector. Do not insert any metal objects such as a wire or screwdriver
into your project. If something should fall into your projector, disconnect it immediately and have the object removed
by a qualified service personnel.
• Do not place any objects on top of the projector.
• Do not touch the power plug during a thunderstorm. Doing so can cause electrical shock or fire.
• The projector is designed to operate on a power supply of 100-240V AC 50/60 Hz. Ensure that your power supply
fits this requirement before attempting to use your projector.
• Do not look into the lens while the projector is on. Serious damage to your eyes could result.
• Keep any items such as magnifying glass out of the light path of the projector.The light being projected from the lens
is extensive, therefore any kind of abnormal objects that can redirect light coming out of the lens, can cause unpre-
dictable outcome such as fire or injury to the eyes.
• Do not cover the lens with the black lens cap or equivalent while the projector is on. Doing so can lead to melting of
the cap and possibly burning your hands due to the heat emitted from the light output.
• Do not place any objects, which are easily affected by heat, in front of the projector lens or a projector exhaust vent.
Doing so could lead to the object melting or getting your hands burned from the heat that is emitted from the light
output and exhaust.
• Handle the power cable carefully. A damaged or frayed power cable can cause electric shock or fire.
- Do not use any power cables than the supplied one.
- Do not bend or tug the power cable excessively.
- Do not place the power cable under the projector, or any heavy object.
- Do not cover the power cable with other soft materials such as rugs.
- Do not heat the power cable
- Do not handle the power plug with wet hands.
• Turn off the projector, unplug the power cable and have the object removed by a qualified NEC service personnel
under the following conditions:
- When the power cable or plug is damaged or frayed.
- If liquid has been spilled into the projector, or if it has been exposed to rain or water.
- If the projector does not operate normally when you follow the instructions described in this user's manual.
- If the projector has been dropped or the cabinet has been damaged.
- If the projector exhibits a distinct change in performance, indicating a need for service.
- If the projector is not to be used for an extended period of time.
• Disconnect the power cable and any other cables before carrying the projector
• Turn off the projector and unplug the power cable before cleaning the cabinet or replacing the lamp.
CAUTION
• Do no use the tilt-foot for purposes other than originally intended. Misuses such as using the tilt foot to carry or
hang (from the wall or ceiling) the projector can cause damage to the projector.
• Do not send the projector in the soft case by parcel delivery service or cargo shipment. The projector inside
the soft case could be damaged.
• Select [High] in Fan mode if you continue to use the projector for consecutive days. (From the menu, select
[Setup - Options] → [Fan Mode] → [High].)
• Do not unplug the power cable from the wall outlet or projector when the projector is powered on. Doing so can
cause damage to the AC IN connector of the projector and (or) the prong plug of the power cable.
• Do not turn off the AC power for 60 seconds after the lamp is turned on and while the POWER indicator is
blinking green.
Doing so could cause premature lamp failure.
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Information
Remote Control Precautions
•
•
•
•
•
•
•
•
Handle the remote control carefully.
If the remote control gets wet, wipe it dry immediately.
Avoid excessive heat and humidity.
Do not heat, take apart, or throw batteries into fire.
If you will not be using the remote control for a long time, remove the batteries.
Ensure that you have the batteries' polarity (+/–) aligned correctly.
Do not use new and old batteries together, or use different types of batteries together.
Dispose of used batteries according to your local regulations.
Lamp Replacement
•
•
Be sure to replace the lamp when the message [The lamp has reached the end of its usable life. Please
replace the lamp.] appears. If you continue to use the lamp after the lamp has reached the end of its usable
life, the lamp bulb may shatter, and pieces of glass may be scattered in the lamp case. Do not touch them as the
pieces of glass may cause injury.
If this happens, contact your dealer for lamp replacement.
A Lamp Characteristic
The projector has a high-pressure mercury lamp as a light source.
A lamp has a characteristic that its brightness gradually decreases with age. Also repeatedly turning the lamp on
and off will increase the possibility of its lower brightness.
CAUTION:
When removing the lamp from a ceiling-mounted projector, make sure that no one is under the projector. Glass
fragments could fall if the lamp has been burned out.
iv
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Important Information ...........................................................................i
1. Introduction........................................................................................1
ᕡ What's in the Box? ........................................................................................................ 1
ᕢ Introduction to the Projector ......................................................................................... 2
ᕣ Part Names of the Projector ......................................................................................... 4
Top Features ........................................................................................................... 6
Terminal Panel Features ......................................................................................... 6
ᕤ Part Names of the Remote Control .............................................................................. 7
Battery Installation ............................................................................................. 8
Remote Control Precautions.............................................................................. 8
Operating Range for Wireless Remote Control.................................................. 8
2. Installation and Connections.........................................................9
ᕡ Setting Up the Screen and the Projector ...................................................................... 9
Selecting a Location................................................................................................ 9
Throw Distance and Screen Size.......................................................................... 10
ᕢ Making Connections ................................................................................................... 12
Connecting Your PC or Macintosh Computer........................................................ 12
To connect SCART output (RGB) ......................................................................... 13
Connecting Your DVD Player with Component Output .......................................... 14
Connecting Your VCR or Laser Disc Player .......................................................... 15
Connecting the Supplied Power Cable ................................................................. 16
3. Projecting an Image (Basic Operation)...................................... 17
ᕡ Turning on the Projector ............................................................................................. 17
Note on Startup Screen (Menu Language Select screen) .................................... 18
ᕢ Selecting a Source ..................................................................................................... 19
ᕣ Adjusting the Picture Size and Position ...................................................................... 20
ᕤ Adjusting Focus Manually........................................................................................... 24
ᕥ Correcting Keystone Distortion Manually ................................................................... 25
ᕦ Optimizing RGB Picture Automatically ....................................................................... 26
ᕧ Adjusting Volume Up or Down .................................................................................... 26
ᕨ Turning off the Projector ............................................................................................. 27
ᕩ After Use..................................................................................................................... 27
v
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
4. Convenient Features...................................................................... 28
ᕡ Turning Off the Image and Sound............................................................................... 28
ᕢ Freezing a Picture....................................................................................................... 28
ᕣ Changing Lamp Mode ................................................................................................ 28
ᕤ Preventing the Unauthorized Use of the Projector ..................................................... 28
ᕥ Using the Optional Remote Mouse Receiver ............................................................. 31
5. Using On-Screen Menu ................................................................. 32
ᕡ Using the Menus......................................................................................................... 32
ᕢ Menu Elements........................................................................................................... 34
ᕣ List of Menu Items ...................................................................................................... 35
ᕤ Menu Descriptions & Functions [Picture].................................................................... 37
ᕥ Menu Descriptions & Functions [Image Options] ....................................................... 38
ᕦ Menu Descriptions & Functions [Setup] ..................................................................... 40
[Setup - General]................................................................................................... 40
[Setup - Installation] .............................................................................................. 41
[Setup - Options] ................................................................................................... 43
ᕧ Menu Descriptions & Functions [Information] ............................................................. 44
ᕨ Menu Descriptions & Functions [Reset] ..................................................................... 45
6. Maintenance .................................................................................... 46
ᕡ Cleaning the Lens and the Focus Sensor ................................................................. 46
ᕢ Cleaning the Cabinet ................................................................................................. 46
ᕣ Replacing the Lamp................................................................................................... 47
7. Appendix ........................................................................................... 50
ᕡ Troubleshooting ......................................................................................................... 50
ᕢ Specifications ............................................................................................................ 53
ᕣ Cabinet Dimensions .................................................................................................. 55
ᕤ Pin Assignments of D-Sub COMPUTER Input Connector ........................................ 56
ᕥ Compatible Input Signal List ...................................................................................... 57
ᕦ PC Control Codes and Cable Connection ................................................................. 58
ᕧ Troubleshooting Check List........................................................................................ 59
ᕨ TravelCare Guide ....................................................................................................... 61
vi
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Introduction
ᕡ What's in the Box?
Make sure your box contains everything listed. If any pieces are missing, contact your dealer.
Please save the original box and packing materials if you ever need to ship your projector.
Projector
T
C
E
L
E
S
U S
F O C
D J .
A
T O
A U
C E
U R
O
S
D
B Y
T A N
/ S
O N
P
P O W E R
S T A T U S
L A M
Lens cap
Soft case
(24F41351)
(24BS7551)
O
F
F
FO
CU
S
P
O
W
P
E
R
IC
-
M
O
N
U
T
E
M
P
A
E
N
G
E
U
U
P
D
O
W
N
ENTER
L
-
C
L
IC
K
E
X
E
M
IT
O
S
U
S
-
O
E
R-CLICK
V
LA
MP
O
P
L
M
U
M
E
ODE
A
S
P
E
C
T
IC
T
H
E
U
R
L
P
E
F
R
E
E
Z
E
Power cable
(US: 7N080204)
(EU: 7N080008)
VGA signal cable
(7N520054)
Remote control
(7N900681)
Batteries (AAA
ן 2) For North America only
Registration card
Limited warranty
For Europe only
Guarantee policy
Quick Setup Guide
Important Information
CD-ROM
User’s manual
1
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Introduction
ᕢ Introduction to the Projector
This section introduces you to your new projector and describes the features and controls.
Congratulations on Your Purchase of the Projector
This projector is one of the very best projectors available today.The projector enables you to project precise images up
to 300 inches across (measured diagonally) from your PC or Macintosh computer (desktop or notebook), VCR, DVD
player, document camera, or a laser disc player.
You can use the projector on a tabletop or cart, you can use the projector to project images from behind the screen,
and the projector can be permanently mounted on a ceiling*1. The remote control can be used wirelessly.
1
*
Do not attempt to mount the projector on a ceiling yourself.
The projector must be installed by qualified technicians in order to ensure proper operation and reduce the
risk of bodily injury.
In addition, the ceiling must be strong enough to support the projector and the installation must be in accor-
dance with any local building codes. Please consult your dealer for more information.
Features you'll enjoy:
•
Auto Focus function
When you turn on the power, change the zoom or reposition the projector, the Auto Focus function will work
instantly.
The focus sensor on the projector detects the distance to the screen and automatically adjusts the focus of an
image as well as reducing the required set-up time.
•
•
Auto vertical keystone correction up to +/– 16 degrees
Built-in Wall Color Correction presets provide for adaptive color correction when projecting onto non-white
screen material
Direct Power Off
•
The projector has a feature called "Direct Power Off". This feature allows the projector to be turned off (even
when projecting an image) using a power strip equipped with a switch and a breaker.
Also, the power cable can be removed immediately after turning off the projector.
HDTV (1080i, 720p) and SDTV (576p, 480p) compatibility
•
•
•
•
•
•
•
Integrated de-interlace video processing technology
Display popular wide screen and full screen aspect ratios – 16:9 and 4:3
Built-in speaker for an integrated audio solution
High resolution display - up to SXGA+ compatible, XGA native resolution.
Multiple video mode selections (depending on your source)
Safety protect by Security function
Security feature prevents unauthorized individuals from displaying images.
You can control the projector with a PC or control system using the PC Control port.
Easy set up and operation
•
•
•
The contemporary cabinet design is light, compact and complements any office, boardroom or Auditorium.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Introduction
About this user's manual
The fastest way to get started is to take your time and do everything right the first time. Take a few minutes now to
review the user's manual.This may save you time later on. At the beginning of each section of the manual you'll find an
overview. If the section doesn't apply, you can skip it.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Introduction
ᕣ Part Names of the Projector
Front/Top
Adjustable Tilt Foot Button
Zoom Lever
Controls
T
C
E
L
E
S
S
U
C
O
F
.
J
D
A
O
T
U
A
E
C
R
U
O
S
Y
B
D
N
A
T
/ S
N
O
R
E
S
W
U
O
P
T
P
A
M
T
S
A
L
Remote sensor
Built-in Security Slot ( )*
Monaural Speaker (1W)
Lens
Focus sensor
Ventilation (outlet)
Heated air is exhausted from here.
Lens Cap
Adjustable Tilt Foot
*
This security slot supports the MicroSaver ® Security System. MicroSaver ® is a registered trademark of
Kensington Microware Inc. The logo is trademarked and owned by Kensington Microware Inc.
Rear
L
A
S
M
P
TA
TU
P
O
S
W
ER
O
N
/S
T
A
N
D
B
Y
S
O
U
C
R
C
O
M
E
P
U
T
E
R
A
U
IN
T
O
A
D
J
.
F
O
C
U
V
S
ID
SELECT
E
O
IN
S
-V
ID
EO
IN
A
U
D
IO
IN
P
C
C
O
N
T
R
O
L
Ventilation (inlet)
Terminal Panel
AC Input
Connect the supplied power cable's three-pin plug here, and
4
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Introduction
Top Features
8
9
1
4 3
5
6
7
SELECT
LAMP
STATUS
POWER
SOURCE
AUTO ADJ.
FOCUS
ON/STAND BY
10
11
2
8. MENU Button
9. SELECT ̆̄̇̈/ Volume ̇̈/ Keystone ̆̄ But-
tons
10. ENTER Button
11. EXIT Button
Terminal Panel Features
1
2
3
4
5
COMPUTER IN
VIDEO IN
S-VIDEO IN
AUDIO IN
PC CONTROL
1. COMPUTER IN/ Component Input Connector (Mini
Use this port to connect a PC or control system. This
enables you to control the projector using serial com-
munication protocol. If you are writing your own pro-
3. S-VIDEO IN Connector (Mini DIN 4 Pin)
6
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Introduction
ᕤ Part Names of the Remote Control
1
2
OFF
ON
POWER
3
FOCUS PIC-MUTE
PAGE
UP
4
7
6
5
8
DOWN
MENU
ENTER
EXIT
10
9
L-CLICK
MOUSE
R-CLICK
12
15
17
16
19
11
13
14
VIDEO COMPUTER AUTO ADJ.
S-VIDEO LAMP MODE
VOLUME ASPECT
HELP
21
PICTURE FREEZE
18
22
20
7. MENU Button
8. SELECT Buttons
9. ENTER Button
10. EXIT Button
* Available only when the optional remote mouse receiver is connected with your computer.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Introduction
Battery Installation
1 Press firmly and slide the
2 Install new batteries (AAA). En-
3 Slip the cover back over the bat-
teries until it snaps into place. Do
not mix different types of batter-
ies or new and old batteries.
battery cover off.
sure that you have the batteries'
polarity (+/–) aligned correctly.
Remote Control Precautions
•
•
•
•
•
•
•
•
Handle the remote control carefully.
If the remote control gets wet, wipe it dry immediately.
Avoid excessive heat and humidity.
Do not heat, take apart, or throw batteries into fire.
If you will not be using the remote control for a long time, remove the batteries.
Ensure that you have the batteries' polarity (+/–) aligned correctly.
Do not use new and old batteries together, or use different types of batteries together.
Dispose of used batteries according to your local regulations.
Operating Range for Wireless Remote Control
30˚
30˚
Remote control
Remote sensor on projector cabinet
7m/22 feet
•
•
The infrared signal operates by line-of-sight up to a distance of about 22 feet/7 m and within a 60-degree angle of
the remote sensor on the projector cabinet.
The projector will not respond if there are objects between the remote control and the sensor, or if strong light falls
on the sensor. Weak batteries will also prevent the remote control from properly operating the projector.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Installation and Connections
This section describes how to set up your projector and how to connect video and audio sources.
Your projector is simple to set up and use.
But before you get started, you must first:
ᕡ
ᕢ
Set up a screen and the projector.
Connect your computer or video equip-
ᕣ
Connect the supplied power cable. See
NOTE: Ensure that the power cable and any other
cables are disconnected before moving the pro-
jector. When moving the projector or when it is
not in use, cover the lens with the lens cap.
To the wall outlet.
ᕡ Setting Up the Screen and the Projector
Selecting a Location
The further your projector is from the screen or wall, the larger the image. The minimum size the image can be is
approximately 30" (0.76 m) measured diagonally when the projector is roughly 47 inches (1.2 m) from the wall or
screen.The largest the image can be is 300" (7.6 m) when the projector is about 480 inches (12.2 m) from the wall or
screen. Use the chart below as a rough guide.
Screen Size (Unit: cm/inch)
609.6(W)
ן 457.2(H) / 240(W)ן 180(H) Screen Size (diagonal: inch)
300"
487.7(W)
ן 365.8(H) / 192(W)ן 144(H) 240"
406.4(W)
ן 304.8(H) / 160(W)ן 120(H) 200"
365.8(W)
ן 274.3(H) / 144(W)ן 108(H) 180"
304.8(W)
ן 228.6(H) / 120(W)ן 90(H) 150"
243.8(W)
ן 182.9(H) / 96(W)ן 72(H) 120"
203.2(W)
ן 152.4(H) / 80(W)ן 60(H) 100"
162.6(W)
ן 121.9(H) / 64(W)ן 48(H) 80"
12.2/480.3
121.9(W)
ן 91.4(H) / 48(W)ן 36(H) 60"
81.3(W)
ן 61.0(H) / 32(W)ן 24(H) 9.8/385.8
40"
61.0(W)
ן 45.7(H) / 24(W)ן 18(H) 8.1/318.9
30"
7.3/287.4
Lens center
6.1/240.2
4.9/192.9
4.0/157.5
1.2/47.2
3.2/126.0
2.4/94.5
1.6/63.0
Distance (Unit: m/inch)
NOTE:
• The distances are indicated by intermediate values between tele and wide. Use as a rule of thumb.
• The Zoom lever adjusts the image size up to +/-10%
• For more details on throw distance, see next page.
• Changing the image size starts the Auto Focus to adjust the focus; changing the throw angle starts the Auto Keystone to correct
the vertical keystone distortion.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Installation and Connections
Throw Distance and Screen Size
The following shows the proper relative positions of the projector and screen. Refer to the table to determine the
position of installation.
Distance Chart
C
Screen center
B
Lens center
α
2.4"/60 mm
Screen bottom
Projector bottom
B = Vertical distance between lens center and screen center
C = Throw distance
α = Throw angle
NOTE: Distances may vary +/-5%.
Screen Size
B
C
α
Screen Size
B
C
α
Diagonal
inch
30
40
60
67
72
80
84
Width
inch
24
32
48
54
58
64
67
Height
inch
18
24
36
40
43
48
50
54
60
72
90
108
120
132
144
156
168
180
Wide – Tele
inch
42 –
Wide – Tele
degree
12.1 - 10.0
Diagonal
mm
762
Width
mm
610
Height
mm
457
610
914
Wide – Tele
mm
Wide – Tele
degree
12.1 - 10.0
inch
9
mm
229
305
457
511
549
610
640
686
51
69
1070
1450
2190
2450
2640
2930
3080
3310
3680
4420
5540
6650
7400
8140
-
-
-
-
-
-
-
-
-
-
-
-
-
-
1290
1740
2630
2940
3170
3520
3700
3970
4410
5300
6640
7980
8870
9760
12
18
20
22
24
25
27
30
36
45
54
60
66
72
78
84
90
57 –
1016
1524
1702
1829
2032
2134
2286
2540
3048
3810
4572
5080
5588
6096
6604
7112
7620
813
11.9
11.8
11.8
11.7
11.8
11.7
11.7
11.7
11.7
11.7
11.7
11.6
11.6
11.6
11.6
11.6
11.6
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
9.9
9.9
9.9
9.8
9.8
9.8
9.8
9.8
9.8
9.8
9.8
9.7
9.7
9.7
9.7
9.7
9.7
11.9
11.8
11.8
11.7
11.8
11.7
11.7
11.7
11.7
11.7
11.7
11.6
11.6
11.6
11.6
11.6
11.6
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
9.9
9.9
9.9
9.8
9.8
9.8
9.8
9.8
9.8
9.8
9.8
9.7
9.7
9.7
9.7
9.7
9.7
86 – 104
96 – 116
104 – 125
115 – 139
121 – 146
130 – 156
145 – 174
174 – 209
218 – 261
262 – 314
291 – 349
320 – 384
350 – 419
379 – 454
408 – 489
438 – 524
1219
1361
1463
1626
1707
1829
2032
2438
3048
3658
4064
4470
4877
5283
5690
6096
1021
1097
1219
1280
1372
1524
1829
2286
2743
3048
3353
3658
3962
4267
4572
90
72
80
96
100
120
150
180
200
220
240
260
280
300
762
914
120
144
160
176
192
208
224
240
1143
1372
1524
1676
1829
1981
2134
2286
8890 - 10650
9630 - 11540
10370 - 12430
11120 - 13320
10
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Installation and Connections
WARNING
Reflecting the Image
* Installing your projector on the ceiling must be done
by a qualified technician.Contact your NEC dealer for
more information.
* Do not attempt to install the projector yourself.
• Only use your projector on a solid, level surface. If the
projector falls to the ground, you can be injured and
the projector severely damaged.
Using a mirror to reflect your projector's image enables
you to enjoy a much larger image when a smaller space
is required. Contact your NEC dealer if you need a mir-
ror system. If you're using a mirror system and your im-
age is inverted, use the MENU and SELECT buttons on
your projector cabinet or your remote control to correct
• Do not use the projector where temperatures vary
greatly. The projector must be used at temperatures
between 41˚F (5˚C) and 104˚F (40˚C). (Eco mode
selected automatically at 95°F to 104°F/35°C to 40°C)
• Do not expose the projector to moisture, dust, or
smoke. This will harm the screen image.
• Ensure that you have adequate ventilation around your
projector so heat can dissipate.Do not cover the vents
on the side or the front of the projector.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Installation and Connections
ᕢ Making Connections
Connecting Your PC or Macintosh Computer
NOTE: When using with a notebook PC, be sure to connect the projector and notebook PC while the projector is in standby mode and
before turning on the power to the notebook PC.
In most cases the output signal from the notebook PC is not turned on unless connected to the projector before being powered up.
* If the screen goes blank while using your remote control, it may be the result of the computer's screen-saver or power manage-
ment software.
Enabling the computer’s external display
Displaying an image on the notebook PC’s screen does not necessarily mean it outputs a signal to the projector.
When using a PC compatible laptop, a combination of function keys will enable/disable the external display.
Usually, the combination of the ‘Fn” key along with one of the 12 function keys gets the external display to come on or
off.For example, NEC laptops use Fn + F3, while Dell laptops use Fn + F8 key combinations to toggle through external
display selections.
COMPUTER IN
AUDIO IN
COMPR IN
VIDEO IN
S-VIDEO IN
AUDIN
PC CONTROL
VGA signal cable (supplied)
To mini D-Sub 15-pin connector on the projector. It
is recommended that you use a commercially
available distribution amplifier if connecting a
signal cable longer than the supplied one.
Audio cable (not supplied)
NOTE: The L-shaped plug of an audio
cable does not fit into the AUDIO IN jack.
PHONE
NOTE: For older Macintosh, use a commercially avail-
able pin adapter (not supplied) to connect to your
Mac's video port.
IBM VGA or Compatibles (Notebook
type) or Macintosh (Notebook type)
NOTE: The projector is not compatible with video decoded outputs of either the NEC ISS-6020 and ISS-6010 switchers.
NOTE: An image may not be displayed correctly when a Video or S-Video source is played back via a commercially available scan
converter.
This is because the projector will process a video signal as a computer signal at the default setting. In that case, do the following.
* When an image is displayed with the lower and upper black portion of the screen or a dark image is not displayed correctly:
Project an image to fill the screen and then press the AUTO ADJ button on the remote control or the projector cabinet.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Installation and Connections
To connect SCART output (RGB)
Projector
COMPUTER IN
Video equipment such as DVD player
COMPUR IN
VIDEO IN
S-VIDEO IN
AUDIO IN
PC CONTROL
Female
ADP-SC1
Commercially available SCART cable
Before connections: An exclusive SCART adapter (ADP-SC1) and a commercially available SCART cable are re-
quired for this connection.
From the menu, select [Setup - Options] → [Signal Select] → [Computer] → [Scart].
SCART is a standard European audio-visual connector for TVs, VCRs and DVD players. It is also referred to as Euro-
connector.
NOTE: Audio signal is not available for this connection.
TIP: The ADP-SC1 SCART adapter is obtainable from your NEC dealer in Europe. Contact your NEC dealer in Europe for more
information.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Installation and Connections
Connecting Your DVD Player with Component Output
AUDIO IN
COMPUTER IN
COMPUTER IN
VIDEO IN
S-VIDEO IN
AUIN
PC CONTROL
Optional 15-pin - to - RCA (female)
ן 3 cable (ADP-CV1) NOTE: The L-shaped plug of an audio cable
does not fit into the AUDIO IN jack.
Audio Equipment
Component video
RCA
ן 3 cable (not supplied)
AUDIO IN
L
R
DVD player
Y
Cb Cr
L
R
Component
AUDIO OUT
Audio cable (not supplied)
A component signal will be automatically displayed. If not, from the menu, select [Setup - Options] → [Signal Select] →
[Computer], and then place a check mark in the “RGB/Component” radio button.
NOTE: Refer to your DVD player's owner's manual for more information about your DVD player's video output requirements.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Installation and Connections
Connecting Your VCR or Laser Disc Player
S-VIDEO IN
VIDEO IN
AUDIO IN
COMPUTER IN
VIDEO IN
S-VO IN
AUDIO IN
PC CONTROL
S-Video cable (not supplied)
Video cable (not supplied)
Audio equipment
VCR/ Laser disc player
L
R
VIDEO S-VIDEO
VIDEO OUT
AUDIO IN
AUDIO OUT
L
R
Audio cable (not supplied)
NOTE: Refer to your VCR or laser disc player owner's manual for more information about your equipment's video output require-
ments.
NOTE:
• An image may not be displayed correctly when a Video or S-Video source is played back in fast-forward or fast-rewind via a scan
converter.
• The AUDIO IN mini jack is shared between VIDEO IN/S-VIDEO IN and COMPUTER IN.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Installation and Connections
Connecting the Supplied Power Cable
Connect the supplied power cable to the projector.
First connect the supplied power cable's three-pin plug to the AC IN of the projector, and then connect the other plug
of the supplied power cable in the wall outlet.
The projector will go into its
standby mode and the
power indicator will glow
LAMP
STATUS
orange.
POWER
ON/STA
LAMP
STATUS
POWER
N/STAND BY
SOURCE
R I
AUTO ADJ.
FOCUS
VIDEO IN
S
E
LE
C
T
S-VIDEO IN
AUDIO IN
PC CONTROL
To wall outlet
Make sure that the prongs are fully inserted into
both the power plug and the wall outlet.
CAUTION:
Do not try to touch the ventilation outlet on the right front (when seen from the front) as it can become heated while
the projector is turned on and immediately after the projector is turned off.
CAUTION:
Do not unplug the power cable from the wall outlet or projector when the project is powered on. Doing so can cause
damage to the AC IN connector of the projector and (or) the prong plug of the power cable.
TIP: To turn off the AC power supply when the projector is powered on, use a power strip equipped with a switch and a breaker.
TIP: The projector can be unplugged during its cool down period after it is turned off.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Projecting an Image (Basic Operation)
This section describes how to turn on the projector and to project a picture onto the screen.
ᕡ Turning on the Projector
NOTE: Before turning on the projector, first connect the supplied power cable's three-pin plug to the AC IN of the projector, and then
connect the other plug of the supplied power cable in the wall outlet. Make sure that the projector is in its standby mode and the
power indicator is glowing orange.
1. Remove the lens cap.
CAUTION:
OFF
ON
POWER
Do not remove the lens cap by pulling on the string.
Doing so can cause mechanical damage to the part
around the lens.
LAMP
STATUS
POWER
FOCUS
PIC-MUTE
PE
ON/SND BY
SOURCE
AUTO ADJ.
DOWN
MENU
2. Press the POWER (ON/STAND BY) button on the pro-
jector cabinet or the POWER ON button on the remote
control for 1 second.
The POWER indicator will turn to green and the projector
will become ready to use.
Standby
Blinking
Power On
LAMP
STATUS
POWER
LAMP
STATUS
POWER
LAMP
STATUS
POWER
TIP:
* Turning on the projector will instantly cause the Auto Focus
* When the key lock symbol (
Steady orange light
Blinking green Steady green
light light
) is displayed at the bottom
right of the menu, it means that the Control Panel Lock is turned
After you turn on your projector, ensure that the computer
or video source is turned on and that your lens cap is re-
moved.
NOTE: When no signal is available, a blue or black screen is dis-
played.
When the projector displays a blue or black screen, the projector will
automatically switch to the Eco mode.
The projector will return to the Normal mode once a signal is con-
nected.
NOTE: If you turn on the projector immediately after the lamp is turned
off or when the temperature is high, the fans run without displaying
an image for some time and then the projector will display the im-
age.
CAUTION:
The projector cannot be turned off for 60 seconds af-
ter the lamp is turned on and while the POWER indica-
tor is blinking green.
• Do not turn off the AC power during this period.
Doing so could cause premature lamp failure.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Projecting an Image (Basic Operation)
Note on Startup screen (Menu Language Select screen)
When you first turn on the projector, you will get the Startup menu. This menu gives you the opportunity to select one
of the nine menu languages.
To select a menu language, follow these steps:
1. Use the SELECT ̆ or ̄ button to select one of the
nine languages from the menu.
OFF
ON
POWER
FOCUS
PIC-MUTE
PAGE
UP
SELECT
DOWN
MENU
ENTER
FOCUS
EXIT
OFF
ON
2. Press the ENTER button to execute the selection.
POWER
FOCUS
PIC-MUTE
PAGE
UP
SELECT
After this has been done, you can proceed to the menu opera-
DOWN
tion.
MENU
ENTER
FOCUS
If you want, you can select the menu language later. (→ [Lan-
EXIT
NOTE: Immediately after turning on the projector, screen flicker may occur. This is normal. Wait 3 to 5 minutes until the lamp lighting
is stabilized.
When the [Lamp mode] is set to [Eco], the LAMP indicator will light green.
If one of the following things happens, the projector will not turn on.
• If the internal temperature of the projector is too high, the projector detects abnormal high temperature. In this
condition the projector will not turn on to protect the internal system. If this happens, wait for the projector's internal
components to cool down.
• When the lamp reaches its end of usable life, the projector will not turn on. If this happens, replace the lamp.
• If the lamp fails to light, and if the STATUS indicator flashes on and off in a cycle of six times, wait a full minute and
then turn on the power.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Projecting an Image (Basic Operation)
ᕢ Selecting a Source
Selecting the computer or video source
NOTE: Turn on the computer or VCR connected to the projector.
Selecting a source from the Source list
Press and quickly release the SOURCE button on the projector cabinet
to display the Source list. Each time the SOURCE button is pressed,
each source name will be highlighted in sequence.
Press the ENTER button or allow 2 seconds to elapse.
The selected signal will be displayed.
SELECT
LAMP
STATUS
POWER
ON/STAND BY
SOCE
AUTO ADJ.
FOCUS
L-CLICK
R-CLICK
MOUSE
VIDEO COMPUTER AUTO ADJ.
S-VIDEO LAMODE
VOLUME
P
Detecting the Signal Automatically
PICTURE FREEZE
Press and hold the SOURCE button for a minimum of 2 seconds, the
projector will search for the next available input source.
Using the Remote Control
Press any one of the VIDEO, S-VIDEO and COMPUTER buttons.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Projecting an Image (Basic Operation)
ᕣ Adjusting the Picture Size and Position
Place your projector on a flat level surface and ensure that the
projector is square to the screen.
Lift the front edge of the projector to center the image vertically.
*
If the projected image does not appear square to the
screen then use the Keystone feature for proper adjust-
About Auto Focus
Just placing the projector on a flat level surface makes a focused
About Auto Keystone Correction
Adjusting the height of a projected image or changing the pro-
jection angle will result in the Auto Keystone function to work to
Move the projector left to center the image hori-
zontally on the screen.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Projecting an Image (Basic Operation)
Adjust the Tilt Foot
1. Lift the front edge of the projector.
T
E C
L
S E
S
U
C
O
F
.
J
D
A
O
T
U
A
E
C
R
U
O
S
CAUTION:
Y
B
D
N
A
T
S
/
N
O
S
W E R
O
U
1
2
A T
L A M P S T
P
Do not try to touch the ventilation outlet during Tilt Foot adjustment
as it can become heated while the projector is turned on and during
its cool down period after it is turned off.
3
2. Push and hold the Adjustable Tilt Foot Button on the front of
the projector to extend the adjustable tilt foot (maximum height).
Adjustable Tilt
Foot Button
3. Lower the front of the projector to the desired height.
Ventilation (outlet)
Adjustable Tilt Foot
4. Release the Adjustable Tilt Foot Button to lock the adjustable
tilt foot.
T
C
E
L
E
S
S
U
C
O
F
.
J
D
A
O
T
U
There is approximately 10 degrees (up) of adjustment for the front of
the projector.
A
E
C
R
U
O
S
Y
B
D
N
A
T
/ S
N
O
R
E
S
W
U
O
P
T
A
P
M
A
S T
L
Adjusting the height of a projected image or changing projection angle
will result in Auto Keystone function to work to quickly correct the
vertical distortion. The "Keystone" screen will be displayed.
For operating the "Keystone" screen, see "Correcting Keystone Dis-
4
CAUTION:
Do not use the tilt-foot for purposes other than originally intended.
Misuses such as using the tilt foot to carry or hang (from the wall or
ceiling) the projector can cause damage to the projector.
NOTE: The rear foot height can be adjusted up to 0.1 inch/3 mm (1 degree of angle).
Rotate the rear foot to the desired height in order to square the image on the projec-
tion surface, but the vertical distance from the bottom to the desk or floor should be
0.1” (3 mm) to make the projector horizontal on the flat surface.
L
AM
ST
P
AT
P
US
OW
E
R
O
N
/S
T
A
N
D
B
Y
S
O
U
R
C
E
T
ER
A
IN
U
T
O
A
D
J
.
F
O
C
U
V
S
IDE
SELECT
O
IN
S
-V
ID
E
O
IN
A
UD
IO
I
N
PC
C
O
NT
RO
L
Rear foot
Up
Down
21
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Projecting an Image (Basic Operation)
Zoom
Use the ZOOM lever to adjust the image size on the screen.
NOTE: Rotating the ZOOM lever will cause the focus to be ad-
justed automatically.
Auto Focus
The focus sensor on the projector detects the distance to the screen and automatically adjusts the focus of an image.
•
The Auto Focus function will work when the following tasks are done:
Turning on the power
Changing the zoom lever
Repositioning the projector
Changing the projection angle
-
-
-
-
Effective auto focus range for screen 4:3
Throw distance
Image size (inch)
Tele (Zoom at min.)
Wide (Zoom at max.)
Minimum distance
Maximum distance
55.1"/1.4 m
32"
39"
216.5"/5.5 m
124"
149"
When the throw distance is beyond 5.5 m/216.5", it means that the focus sensor will not work correctly and that you
need to use the FOCUS button to adjust the focus manually.
NOTE: In some cases, the Auto Focus may not work correctly or the Auto Focus range can be made narrower, depending on the
environmental conditions.
The Auto Focus function will not work under the following circumstances
• When using a transparent screen.
• When there are objects between the focus sensor of the projector and the screen.
• When moving the projector so slowly that the focus sensor cannot detect the distance to the screen.
• When moving the screen, not the projector, because the focus sensor cannot detect the distance to the screen
TIP: To turn off the Auto Focus function, from the menu select [Setup - Options] → [Auto Focus] and select [Off].
22
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Projecting an Image (Basic Operation)
Auto Keystone Correction
The Auto Keystone correction feature will correct the vertical distortion of a projected image on the screen. No special
operation required. Just place the projector on a flat surface.
NOTE: When using the Auto Keystone function, heed the following:
• The vertical keystone angle can be corrected between 16 degrees upward and 16 degrees downward from level.
• The Auto Keystone correction will take effect in 2 seconds after changing the projection angle during projection.
• The left and right, or horizontal keystone distortion is not available.
Place the projector so that the lens surface is parallel to the screen.
Also, adjust the height to keep the projector level by rotating the rear feet.
TIP: To turn off the Auto Keystone function, from the menu select [Setup - General] → [Auto Keystone] and select [Off]. (→ page 25)
Even when the menu setting for [Auto Keystone] is turned on, [Keystone] can be adjusted manually.
NOTE: Auto and Manual Keystone correction angle could be less than 16 degrees depending on some kinds of signal and aspect
ratios.
NOTE: The Auto Keystone Correction feature can cause an image to be slightly blurred because the correction is made electronically.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Projecting an Image (Basic Operation)
ᕤ Adjusting Focus Manually
Adjust the focus manually in the following cases:
•
•
•
When adjusting the focus out of the effective range of the automatic focus
When finely adjusting the focus
When the menu setting for [Auto Focus] is turned off
Adjusting with buttons on the cabinet
1. Press the FOCUS button quickly.
SELECT
The focus adjustment screen will be displayed.
LAMP
STATUS
POWER
ON/STAND BY
SOURCE
AUTO ADJ.
FOUS
The focus adjustment screen will be closed if no button operation is
made for 5 seconds.
TIP: If the projector is placed within the effective focus range, pressing
and holding the FOCUS for a minimum of 2 seconds starts the Auto
Focus function.
2. Press the SELECT ̇ or ̈ button to adjust the focus.
SELECT
LAMP
STATUS
POWER
3. Press the EXIT button.
ON/STAND BY
SOURCE
AUTO ADJ.
FOCUS
The focus adjustment screen will be closed.
Adjusting with the remote control
1. Press the FOCUS + or - button.
OFF
ON
POWER
The focus adjustment screen will be displayed.
FOCUS
PIC-MUTE
PAGE
UP
DOWN
ENTER
EXIT
• The focus adjustment screen will be closed if no button operation
is made for 5 seconds.
• Use the FOCUS + or - button to adjust the focus.
2. Press the EXIT button.
The focus adjustment screen will be closed.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Projecting an Image (Basic Operation)
ᕥ Correcting Keystone Distortion Manually
You can also correct the vertical keystone distortion manually.
NOTE: Manual keystone correction is not available when there is no signal received by any input.
Adjust the keystone distortion manually in the following cases:
•
•
To fine tune Keystone correction even after performing the [Auto Keystone] adjustment.
When the menu setting for [Auto Keystone] is turned off
Adjusting with buttons on the cabinet
1. Press the SELECT ̆ or ̄ button with no
menus displayed.
SELECT
The slide bar will be displayed for your adjust-
ment.
LAMP
STATUS
POWER
ON/STAND BY
SOURCE
AUTO ADJ.
FOCUS
2. Press the EXIT button.
The slide bar will be closed.
Adjusting with the remote control
1. Press the MENU button.
The menu will be displayed.
2. Use the SELECT ̄ button to select [Setup -
General] and then press the ENTER button.
3. Select the Keystone function.
Use the SELECT ̄ button to select [Keystone].
25
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Projecting an Image (Basic Operation)
4. Correct the vertical distortion.
Use the SELECT ̇ or ̈ button to correct the verti-
cal keystone distortion.
NOTE: The Keystone Correction feature can cause an image
to be slightly blurred because the correction is made elec-
tronically.
5. Press the EXIT button twice to close the menu.
TIP: You can save the changes using the Keystone Save fea-
ᕦ Optimizing RGB Picture Automatically
Adjusting the Image Using Auto Adjust
Optimizing an RGB image automatically.
Press the AUTO ADJ. button to optimize an RGB image automatically.
This adjustment may be necessary when you connect your computer for the first time.
[Poor picture]
L-CLICK
R-CLICK
MOUSE
VIDEO COMPUTER AUTO ADJ.
SELECT
S-VIDEO LAMP MODE
LAMP
STATUS
POWER
VOLUME ASPECT
PICTURE FREEZE
ON/STAND BY
SOURCE
AUADJ.
FOCUS
[Normal picture]
NOTE:
Some signals may take time to display or may not be displayed correctly.
• The Auto Adjust function does not work for component and video signals.
• If the Auto Adjust operation cannot optimize the RGB signal, try to adjust Horizontal/Vertical Position Clock and Phase manually.
ᕧ Adjusting Volume Up or Down
VIDEO COMPUTER AUTO ADJ.
Sound level from the
speaker can be adjusted.
S-VIDEO LAMP MODE
Increase volume
Decrease volume
VOLUME ASPECT
HELP
PICTURE FREEZE
TIP: When no menus appear, the SELECT ̇ and ̈ buttons on the projector cabinet work as a volume control.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Projecting an Image (Basic Operation)
ᕨ Turning off the Projector
To turn off the projector:
OFF
ON
POWER
First, press the POWER (ON/STAND BY) button on the
projector cabinet or the POWER OFF button on the re-
mote control. The “Power Off / Are you sure?” message
will appear.
FOS
PIC-MUTE
PAGE
UP
LAMP
STATUS
POWER
ON/STD BY
SOURCE
AUTO ADJ.
DOWN
MENU
ENTER
EXIT
Power On
Fan running
Standby
LAMP
STATUS
POWER
LAMP
STATUS
POWER
LAMP
STATUS
POWER
Secondly, press the ENTER button or press the POWER
(ON/STAND BY) or the POWER OFF button again.
The power indicator will glow orange.
Immediately after turning on the projector and displaying
an image, you cannot turn off the projector for 60 sec-
onds.
Steady green light
Blinking
orange light
Steady orange
light
About Direct Power Off
The projector has a feature called "Direct Power Off". This feature allows the projector to be turned off (even when
projecting an image) using a power strip equipped with a switch and a breaker.
NOTE: Do not turn off the projector using the "Direct Power Off" function within 10 seconds of making adjustment or setting changes
and closing the menu.
Doing so can cause loss of adjustments and settings.
CAUTION:
Do not unplug the power cable from the wall outlet or projector when the projector is powered on. Doing so can
cause damage to the AC IN connector of the projector and (or) the prong plug of the power cable.
TIP: To turn off the AC power supply when the projector is powered on, use a power strip equipped with a switch and a breaker.
TIP: The projector can be unplugged during its cool down period after it is turned off.
CAUTION:
Parts of the projector will become heated during operation. Use caution when picking up the projector immediately
after it has been operating.
ᕩ After Use
Preparation: Make sure that the projector is turned off.
1. Unplug the power cable.
2. Disconnect any other cables.
3. Retract adjustable tilt foot if extended.
4. Cover the lens with the lens cap.
5. Put the projector and its accessories in the supplied soft case.
CAUTION:
Use caution when putting the projector in the soft case immediately after the projector has been operating.
The projector cabinet is hot.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Convenient Features
³ Turning off the Image and Sound
Press the PIC-MUTE button to turn off the image and sound for a short
period of time. Press again to restore the image and sound.
OFF
ON
POWER
FOCUS
PIC-MUTE
PAGE
UP
DOWN
MENU
ENTER
EXIT
· Freezing a Picture
Press the FREEZE button to freeze a picture. Press again to resume
motion.
S-VIDEO LAMP MODE
VOLUME ASPECT
HELP
PICTURE FREEZE
ᕣ Changing Lamp Mode
The lamp life can be extended by using the Eco mode.
To change to the “Eco” mode, do the following:
1. Press the LAMP MODE button to display [Lamp Mode] screen.
L-CLICK
R-CLICK
MOUSE
VIDEO COMPUTER AUTO ADJ.
2. Use the SELECT ̆ or ̄ button to select [Eco] mode.
S-VIDEO LAMP MODE
3. Press the ENTER button. Or press the SELECT ̈ button to select
VOLUME ASCT
HELP
[OK] and press the ENTER button.
EZE
To cancel it, select [Cancel] and press the ENTER button.
To change from [Eco] to [Normal], Go back to Step 2 and select [Nor-
mal]. Repeat Step 3.
Normal Mode ........ This is the default setting (100% Brightness).
Eco Mode .............. Select this mode to increase the lamp life and reduce fan
noise (LT35: 77% Brightness, LT30/LT25: 85% Bright-
ness).
ᕤ Preventing the Unauthorized Use of the Projector
A keyword can be set for your projector using the Menu to avoid operation by an unauthorized user. When a keyword
is set, turning on the projector will display the Keyword input screen. Unless the correct keyword is entered, the
projector cannot project an image.
To enable the Security function:
1. Press the MENU button.
The menu will be displayed.
2. Use SELECT ̆ or ̄ button to select [Setup - Installation] → [Security] and press the ENTER button.
The Off/On menu will be displayed.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Convenient Features
3. Select [On] and press the ENTER button.
The [Keyword] screen will be displayed.
4. Type in a combination of the four SELECT ̆̄̇̈ buttons and press the ENTER button.
NOTE: A keyword must be four to 10 digits in length.
The [Confirm Keyword] screen will be displayed.
5. Type in the same combination of SELECT ̆̄̇̈ buttons and press the ENTER button.
The confirmation screen will be displayed.
6. Select [Yes] and press the ENTER button.
The Security function has been enabled.
To turn on the projector when [Security] is enabled:
When the Security function is enabled and the projector is turned on, the projector will display a blue
background.
To display an image at this time, press the MENU button to display the Keyword input screen.
Type in the correct keyword and press the ENTER button.The projector will display an image.
NOTE: The security disable mode is maintained until the main power is turned off or unplugging the power cable.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Convenient Features
To disable the Security function:
1. Press the MENU button.
The menu will be displayed.
2. Select [Setup - Installation] → [Security] and press the ENTER button.
The Off/On menu will be displayed.
3. Select [Off] and press the ENTER button.
The Keyword confirmation screen will be displayed.
4. Type in your keyword and press the ENTER button.
When the correct keyword is entered, the Security function will be disabled.
NOTE: If you forget your keyword, contact your dealer. Your dealer will provide you with your keyword in exchange for your request
code. Your request code is displayed in the Keyword Confirmation screen. In this example [K992-45L8-JNGJ-4XU9-1YAT-EEA2] is
a request code.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Convenient Features
ᕥ Using the Optional Remote Mouse Receiver
The optional remote mouse receiver enables you to operate your computer’s mouse functions from the remote control.
It is a great convenience for clicking through your computer-generated presentations.
Connecting the remote mouse receiver to your computer
If you wish to use the remote mouse function, connect the mouse receiver and computer.
The mouse receiver can be connected directly to the computer’s USB port (type A).
NOTE: Depending on the type of connection or OS installed on your computer, you may have to restart your computer or change
your computer settings.
Computer
Remote mouse receiver
To USB port of PC or Macintosh
When operating a computer via the remote mouse receiver
7m/22 feet
30°
30°
Remote sensor on the remote mouse receiver
When connecting using the USB terminal
For PC, the mouse receiver can only be used with a Windows 98/Me/XP*, Windows 2000 or Mac OS X 10.0.0 or later
operating system.
* NOTE: In Windows XP, if the mouse cursor will not move correctly, do the following:
Clear the Enhance pointer precision check box underneath the mouse speed slider in the Mouse Properties dialog box [Pointer
Options tab].
NOTE: Wait at least 5 seconds after disconnecting the mouse receiver before reconnecting it and vice versa. The computer may not
identify the mouse receiver if it is repeatedly connected and disconnected in rapid intervals.
Operating your computer’s mouse from the remote control
You can operate your computer's mouse from the remote control.
PAGE UP/DOWN Button .... scrolls the viewing area of the window or to move to the previous or next slide in PowerPoint on
your computer.
SELECT ̆̄̇̈ Buttons .. moves the mouse cursor on your computer.
MOUSE L-CLICK Button .... works as the mouse left button.
MOUSE R-CLICK Button.... works as the mouse right button.
NOTE: When you operate the computer using the SELECT ̆̄̇ or ̈ button with the menu displayed, both the menu and the
mouse pointer will be affected. Close the menu and perform the mouse operation.
TIP: You can change the Pointer speed on the Mouse Properties dialog box on the Windows. For more information, see the user
documentation or online help supplied with your computer.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Using On-Screen Menu
ᕡ Using the Menus
NOTE: The on-screen menu may not be displayed correctly while an interlaced motion video image is projected.
1. Press the MENU button on the remote control or projector cabinet to display the main menu.
OFF
ON
POWER
FOCUS
PIC-MUTE
PAGE
UP
DOWN
SELECT
MENU
ENTER
FOCUS
EXIT
2. Press the SELECT ̆̄ buttons on the remote control or the projector cabinet to highlight the menu for the
item you want to adjust or set.
OFF
ON
POWER
FOCUS
PIC-MUTE
PAGE
UP
Highlight
Indicates the selected menu
or item.
DOWN
SELECT
MENU
ENTER
FOCUS
EXIT
3. Press the ENTER button on the remote control or the projector cabinet to select a submenu or item.
OFF
ON
POWER
FOCUS
PIC-MUTE
PAGE
UP
DOWN
SELECT
MENU
ENTER
FOCUS
EXIT
4. Use the SELECT ̆̄ buttons on the remote control or the projector cabinet to select the item you want to
adjust or set.
OFF
ON
POWER
FOCUS
PIC-MUTE
PAGE
UP
DOWN
SELECT
MENU
ENTER
FOCUS
EXIT
32
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Using On-Screen Menu
5. Adjusting the level of a selected item or selecting an item.
Slide bar
OFF
ON
POWER
Solid triangle
FOCUS
PIC-MUTE
PAGE
UP
DOWN
MENU
ENTER
Return key symbol
Radio button
SELECT
FOCUS
For Adjusting items (Slide bar)
Slide bar..................... Indicates settings or the direction of adjustment.
• Use the SELECT ̇̈ buttons to adjust the item.
For Selecting items (Solid triangle)
Solid triangle .............. Indicates further choices are available. A highlighted triangle indicates the item is active.
• Use the SELECT ̇̈ buttons to select the item.
For Selecting items (Return key symbol, Radio button)
Return key symbol Indicates further choices are available.
Radio button .............. Use this round button to select an option in a dialog box.
1) Press the ENTER button. The selected item will be displayed.
2) Use the SELECT ̆̄ buttons to highlight the item you want to set.
Changes are stored until you adjust it again.
Press the EXIT button to return to the previous screen.
6. Repeat steps 2-5 to adjust an additional item, or press the EXIT button several times to close the menu.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Using On-Screen Menu
· Menu Elements
Slide bar
Title
Highlight
Solid triangle
Source
Key Lock symbol
Thermometer symbol
Off Timer remaining time
Radio button
OK button
Cancel button
Menu windows or dialog boxes typically have the following elements:
Title .......................................... Indicates the menu title.
Highlight................................... Indicates the selected menu or item.
Source ...................................... Indicates the currently selected source.
Off timer remaining time .......... Indicates the remaining countdown time when the Off Timer is preset.
Solid triangle ............................ Indicates further choices are available. A highlighted triangle indicates the item is active.
Radio button ............................ Use this round button to select an option in a dialog box.
Slide bar ................................... Indicates settings or the direction of adjustment.
OK button ................................. Press to confirm your setting. You will return to the previous menu.
Cancel button ........................... Press to cancel your setting. You will return to the previous menu.
Key Lock symbol ...................... Indicates the Control Panel Lock is enabled.
Thermometer symbol ............... Indicates the lamp mode is forcibly set to Eco mode because the internal temperature is too
high.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Using On-Screen Menu
» List of Menu Items
Some menu items are not available depending on the input source.
Picture
Default
Item
Resttable
Preset
1 to 5
Detail Settings Reference
Gamma Correction
Color Temperature
White Peaking
Brightness
Contrast
Sharpness
Color
*
*
*
*
Presentation, Video, Movie, Graphic, sRGB
Dynamic, Natural, Black Detail
5000, 6500, 7800, 8500, 9300, 10500
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Hue
Reset
Resttable
Image Options
Default
*
Item
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Aspect Ratio
Cinema Position
Position/Clock
Normal, Cinema, Native
Horizontal
Vertical
Clock
*
*
*
*
Off
Off
Phase
Noise Reduction
Telecine
Off, On
Off, Auto
Setup
Default
On
Item
Resttable
General
Auto Keystone
Keystone
Keystone Save
Wall Color
Off, On
Yes
Yes
Yes
Yes
Off
Off
Off, On
Off, Blackboard, Blackboard(Gray), Light yellow,
Light green, Light blue, Sky blue, Light rose, Pink
Normal, Eco
Lamp Mode
Language
Normal
English
Yes
–
English, Deutsch, Français, Italiano, Español,
Svenska,
, Dansk, Português,
,
Magyar, Polski, Nederlands, Suomi, Norsk, Türkçe,
,
,
,
Installation
Orientation
Desktop Front Desktop Front, Ceiling Rear, Desktop Rear,
Ceiling Front
Yes
Communication Speed
Control Panel Lock
Security
38400bps 4800bps/9600bps/19200bps/38400bps
–
Yes
–
Off
Off, On
Off
Off, On
Menu Color Select
Menu Display Time
Background
Off Timer
Auto Focus
Auto Start
Power Management
Fan Mode
Color
Color, Monochrome
Yes
Yes
–
Yes
Yes
Yes
Yes
Yes
Auto 45 sec Manual/Auto 5 sec/Auto 15sec/Auto 45 sec
Blue
Off
On
Off
Blue, Black
Off/0:30/1:00/2:00/4:00/8:00/12:00/16:00
Off, On
Off, On, Last
Off/0:05/0:10/0:20/0:30
Auto, High
Options
Off
Auto
Signal Select
Computer
RGB/Component RGB/Component, Scart
Yes
Yes
Video
Auto
Auto, NTSC3.58, NTSC4.43, PAL, PAL-M,
PAL-N, PAL60, SECAM
S-Video
Auto
Auto, NTSC3.58, NTSC4.43, PAL, PAL-M,
PAL-N, PAL60, SECAM
Yes
* The asterisk (*) indicates that the default setting varies depending on the signal.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Using On-Screen Menu
Information
Item
Usage Time
Lamp Life Remaining
Lamp Hours Used
Projector Hours Used
Horizontal Frequency
Vertical Frequency
Video Type
Source
NTSC, NTSC3.58, NTSC4.43, PAL, PAL-M, PAL-N, PAL60, SECAM
Separate Sync, Composite Sync, G-Sync
Sync Type
Sync Polarity
Scan Type
Interlace, Non-Interlace
Version
Firmware
Data
Reset
Item
Current Signal
All Data
Clear Lamp Hours
36
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Using On-Screen Menu
¿ Menu Descriptions & Functions [Picture]
Preset
When selecting user adjustable presetting (Preset), the submenu will be displayed.
You can customize each gamma or color.To do so, first select [Preset] and press the ENTER button, and then proceed
with the following steps.
Detail Settings
Selecting Reference Setting [Reference]
This option allows you to select one of 5 user adjustable presettings. There are 5 factory presets optimized for
various types of images, you can set user adjustable settings.
Presentation .......... Recommended for making a presentation using a PowerPoint file.
Video ..................... Recommended for standard video such as a TV program.
Movie .................... Recommended for film based video such as a movie (DVD or HDTV).
Graphic.................. Recommended for viewing accurate colors in graphics.
sRGB ..................... Standard color values.
Selecting Gamma Correction Mode [Gamma Correction]
Each mode is recommended for:
Dynamic ................ Creates a high-contrast picture.
Natural .................. Natural reproduction of the picture.
Black Detail ........... Emphasizes detail in dark areas of the picture.
Adjusting Color Temperature [Color Temperature]
This option allows you to adjust the color temperature using the slide bar.
Move the slide bar to the right to increase color temperature (more blue); to the left to decrease color temperature
(more red): 5000, 6500, 7800, 8500, 9300, 10500K.
NOTE:
• When [Presentation] is selected in [Reference], [Color Temperature] is not available.
• When color options other than [Off] is selected in [Wall Color], [Color Temperature] is not available.
• The adjustable range may vary depending on White Peaking adjustment.
Adjusting White Peaking [White Peaking]
This allows you to adjust the drive level of the white areas. As the picture becomes dim, it looks more natural.
NOTE:
• When [Presentation] is selected in [Reference], [White Peaking] is not available.
• When this option is highlighted, pressing the ENTER button will display its slide bar for adjustment.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Using On-Screen Menu
Adjusting Brightness, Contrast, Sharpness, Color and Hue
You can adjust brightness, contrast, sharpness, color and hue.
TIP: When one of Brightness, Contrast, Sharpness, Color or Hue is highlighted, pressing the ENTER button will display its slide bar
for adjustment.
Brightness ............. Adjusts the brightness level or the black level of the image.
Contrast ................ Adjusts the intensity of the image according to the incoming signal (White level of the image).
Sharpness ............. Controls the detail of the image for Video.
Color ..................... Increases or decreases the color saturation level (not valid for RGB).
Hue........................ Varies the color level from +/- green to +/-blue. The red level is used as reference. This adjustment is only
valid for Video and Component inputs (not valid for RGB).
Reset
The Reset feature allows you to change adjustments to the reference data you select.
´ Menu Descriptions & Functions [Image Options]
Selecting Aspect Ratio [Aspect Ratio]
Aspect Ratio allows you to select the best Aspect mode to display your source image.
You can also display the Aspect Ratio window by pressing the ASPECT button on the remote control. (→ page 7)
Normal
Cinema
Native
When 4:3 is selected from the source (i.e. DVD player),
the following selections will display:
Standard
4:3 Aspect
Left and right
stretched
Normal
Cinema
When 16:9 is selected from the source (i.e. DVD
player), the following selections will display:
16:9 image
displayed in 4:3
mode
Left and right
stretched to display
the true aspect
Native (RGB only): Turns off the scaling feature. The projector displays the current image in its true resolution.
38
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Using On-Screen Menu
NOTE:
• When you are displaying an RGB image with a higher resolution than the projector's native resolution, the image will be displayed
in [Normal] even if [Native] is selected.
Only when displaying an RGB image with a lower resolution than the projector's native resolution, will the image be able to be
displayed in its true resolution [Native].
• When [Normal] is selected, an HDTV (1080i/720p) signal will be shown in its true aspect, as is the case when selecting [Cinema].
• You can adjust the image position for Cinema aspect. See [Cinema Position] for setting the image position.
Copyright
Please note that using this projector for the purpose of commercial gain or the attraction of public attention in a venue such as a
coffee shop or hotel and employing compression or expansion of the screen image with a [Aspect Ratio] setting may raise concern
about the infringement of copyrights which are protected by copyright law.
Adjusting the Vertical Position of Image [Cinema Position] (for Cinema only)
This feature adjusts the vertical position of the image when viewing video with Cinema aspect ratio selected.
When [Cinema] is selected in [Aspect Ratio], the image is displayed with black borders on the top and bottom.
You can adjust the vertical position between top and bottom.
NOTE: This option is available only when “Cinema” is selected in Aspect Ratio.
Adjusting Horizontal/Vertical Position, Clock and Phase [Position/Clock]
You can adjust the image manually for position and stability; [Horizontal], [Vertical], [Clock] and [Phase].
[Horizontal/Vertical]
Adjusts the image location horizontally and vertically.
[Clock] (available for RGB signal only)
Use this item to fine tune the computer image or to remove any vertical banding that might appear. This function
adjusts the clock frequencies that eliminate the horizontal banding in the image. This adjustment may be neces-
sary when you connect your computer for the first time.
[Phase] (available for RGB signal only)
Use this item to adjust the clock phase or to reduce video noise, dot interference or cross talk. (This is evident
when part of your image appears to be shimmering.)
Use [Phase] only after the [Clock] is complete.
Turning on Noise Reduction [Noise Reduction]
Turn on or off the noise reduction feature. To reduce video noise, select On.
NOTE:
• This feature is not available for 480p, 576p, 720p, 1080i and RGB signals
• Noise reduction set to off gives best image quality by way of higher bandwidth. Noise reduction set to on softens the image.
Setting Telecine Mode [Telecine]
Use 3:2 or 2:2 pull down correction to eliminate jitter and artifacts in video.
Auto ...................... For film source such as a DVD player.
Off ......................... For signals other than film sources.
NOTE: This feature is not available for 480p, 576p, 720p, 1080i and RGB signals
39
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Using On-Screen Menu
² Menu Descriptions & Functions [Setup]
[Setup - General]
Enabling Auto Keystone [Auto Keystone]
This feature allows the projector to detect its tilt and correct vertical distortion automatically.
Turn on the Auto Keystone feature, select “On".
Correcting Vertical Keystone Distortion Manually [Keystone]
TIP: When this option is highlighted, pressing the ENTER button will display its slide bar for adjustment.
Saving Vertical Keystone Correction [Keystone Save]
This option enables you to save your current keystone settings.
Off ......................... Does not save current keystone correction settings
On ......................... Saves current keystone correction settings
Saving your change once affects all sources. The changes are saved when the projector is off.
NOTE: When [Auto Keystone] is set to [On], [Keystone Save] is not available. Next time you turn on the power, the Auto Keystone
function will work and the data stored with [Keystone Save] will be invalid.
Selecting Wall Color Correction Mode [Wall Color]
This function allows for quick adaptive color correction in applications where the screen material is not white.
The following 9 options are available: Off, Blackboard, Blackboard (Gray), Light yellow, Light green, Light blue, Sky
blue, Light rose and Pink.
Selecting Lamp Mode [Lamp Mode]
This feature enables you to select two brightness modes of the lamp: Normal and Eco modes. The lamp life can be
extended by using the Eco mode.
Normal Mode ........ This is the default setting (100% Brightness).
Eco Mode .............. Select this mode to increase the lamp life and reduce fan noise (LT35: 77% Brightness, LT30/LT25: 85%
Brightness).
Selecting Menu Language [Language]
You can choose one of 20 languages for the on-screen menu.
40
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Using On-Screen Menu
[Setup - Installation]
Selecting Projector Orientation [Orientation]
This sets your image for your type of projection application. The options are:
desktop front projection, ceiling rear projection, desktop rear projection, and ceiling front projection.
Desktop front
Ceiling rear
Desktop rear
Ceiling front
Selecting Communication Speed [Communication Speed]
This feature sets the baud rate of the PC Control port (Mini DIN 8 Pin). It supports data rates from 4800 to 38400 bps.
The default is 38400 bps.
Select the appropriate baud rate for your equipment to be connected (depending on the equipment, a lower baud rate
may be recommended for long cable runs).
Disabling the Cabinet Buttons [Control Panel Lock]
This option turns on or off the Key Lock function for cabinet buttons.
NOTE:
• The Control Panel Lock setting will not affect the remote control or PC Control Functions.
• When the cabinet buttons are disabled, pressing and holding the EXIT button for about 10 seconds will change the setting to
enable.
41
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Using On-Screen Menu
Enabling Security [Security]
This feature turns on or off the Security function.
Selecting Menu Color [Menu Color Select]
You can choose between two color modes for menu color: color and monochrome.
Selecting Menu Display Time [Menu Display Time]
This option allows you to select how long the projector waits after the last touch of a button to turn off the menu.
The preset choices are “Manual”, “Auto 5 sec”, “Auto 15 sec”, and “Auto 45 sec”.
Selecting a Color for Background [Background]
Use this feature to display a blue/black screen when no signal is available.
42
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Using On-Screen Menu
[Setup - Options]
Setting Off Timer [Off Timer]
You can use the Off Timer feature to turn off the projector automatically at a preset time.
Eight preset times can be selected:Off, 0:30, 1:00, 2:00, 4:00, 8:00, 12:00 and 16:00.
Enabling or Disabling Auto Focus [Auto Focus]
NOTE:
When the “Auto Focus” is on, the Auto Focus function works instantly under the following conditions:
• When you turn on the power.
• When you change the zoom.
• When you reposition the projector.
Enabling Auto Start [Auto Start]
Turns the projector on automatically when the power cable is inserted into an active power outlet.This eliminates the
need to always use the POWER button on the remote control or projector cabinet.
Last ....................... When the projector is turned off with the POWER button (placed into stand-by mode) and then the power
cable is disconnected, Auto Start will not be activated after power (AC) is applied.
When the projector is turned off with the "Direct Power Off" function or after power (AC) is removed (no
stand-by mode), Auto Start will be activated after power (AC) is applied.
The "Direct Power Off" function means you can turn off the power (AC) to the projector using a power strip
equipped with a switch and a breaker.
Enabling Power Management [Power Management]
When this option is selected you can enable the projector to automatically turn off (at the selected time:5min., 10min.,
20min., 30min.) if there is no signal received by any input.
Enabling Fan Speed Mode [Fan Mode]
This option allows you to select two modes for fan speed: Auto mode and High speed mode.
Auto ...................... The built-in fans automatically run at a variable speed according to the internal temperature.
High ...................... The built-in fans run at a fixed high speed.
When you wish to cool down the temperature inside the projector quickly, select [High].
NOTE: It is recommended that you select High speed mode if you continue to use the projector for consecutive days.
Selecting Signal Format [Signal Select]
[Computer]
Normally select [RGB/Component] and the projector automatically detects a component signal. Select [Scart] for the
European Scart signal.
[Video & S-Video System Select]
This feature enables you to select video standards automatically or manually.
Normally select [Auto] and the projector will automatically detect the video standard.
In the case where the projector has difficulty detecting the video standard, select the appropriate video standard from
the menu. This must be done for Video and S-Video respectively.
43
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Using On-Screen Menu
¶ Menu Descriptions & Functions [Information]
Displays the status of the current signal and lamp usage. This item has three pages. The information included is as
follows:
[Usage Time]
[Lamp Life Remaining] (%)*
[Lamp Hours Used] (H)
[Projector Hours Used] (H)
*
The progress indicator shows the percentage of remaining bulb life.
The value informs you of the amount of lamp usage. When the remaining lamp time reaches 0, the Remaining
Lamp Time bar indicator changes from 0% to 100 Hours and starts counting down.
If the remaining lamp time reaches 0 hours, the projector will not turn on regardless of whether the lamp mode
is set to Normal or Eco.
Lamp life(H)
Model
Replacement lamp
Normal
Eco
LT35
LT30/LT25
LT35LP
LT30LP
2000
2500
[Source]
[Horizontal Frequency]
[Video Type]
[Vertical Frequency]
[Sync Type]
[Sync Polarity]
[Scan Type]
[Version]
[Firmware] Version
[Data] Version
44
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Using On-Screen Menu
ᕨ Menu Descriptions & Functions [Reset]
Returning to Factory Default [Reset]
The Factory Default feature allows you to change adjustments and settings to the factory preset for a (all) source (s)
except the following:
[Current Signal]
Resets the adjustments for the current signal to the factory preset levels.
The items that can be reset are: [Preset], [Brightness], [Contrast], [Color], [Hue], [Sharpness], [Aspect Ratio],
[Horizontal Position], [Vertical Position], [Clock], [Phase], [Noise Reduction], [Telecine] and [Volume].
[All Data]
Reset all the adjustments and settings for all the signals to the factory preset.
All items can be reset except [Language], [Background], [Communication Speed], [Security], [Lamp Life Remain-
ing], [Lamp Hours Used], and [Projector Hours Used].
To reset the lamp usage time, see “Clearing Lamp Hour Meter [Clear Lamp Hours]” below.
Clearing Lamp Hour Meter [Clear Lamp Hours]
Resets the lamp clock back to zero. Selecting this option displays submenu for a confirmation.
NOTE: The projector will turn off and go into standby mode after 2100 hours (up to 2600 hours in Eco mode) of service.
If this happens, press the HELP button on the remote control for 10 seconds to reset the lamp clock back to zero.
When the lamp time clock is reset to zero, the LAMP indicator goes out.
Do this only after replacing the lamp.
45
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Maintenance
This section describes the simple maintenance procedures you should follow to clean the focus sensor, lens and
replace the lamp.
ᕡ Cleaning the Lens and Focus Sensor
Cleaning the lens
Use a blower or lens paper to clean the lens, and be careful not to scratch or mar the lens.
T
L E C
S E
S
U
C
O
F
.
J
D
A
O
T
U
A
E
C
R
U
O
S
Y
B
D
N
A
T
S
/
N
O
R
E
S
W
U
O
P
T
P
A
M
T
S
A
L
Cleaning the focus sensor
Use a blower or lens paper to clean the focus sensor.
Keep finger prints off the focus sensor. Leaving finger prints in the focus sensor might cause poor focus or short auto
focus range.
T
C
E
L
E
S
F O C U S
A D J .
A U T O
U R C E
S O
O N / S T A N D B Y
R
W E
O
P
T U S
P
S T A
L A M
· Cleaning the Cabinet
1. Turn off the projector before cleaning.
2. Vacuum the ventilation inlet of the cabinet.
LAM
S
T
P
A
TU
S
P
O
W
E
R
/S
T
A
N
D
B
Y
S
O
U
C
R
C
O
M
E
P
U
TE
R
A
U
IN
T
O
A
D
J.
F
O
C
U
V
S
ID
SE
E
O
IN
L
E
C
T
S
-V
ID
E
O
IN
A
U
D
IO
IN
P
C
C
O
N
T
R
O
L
46
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Maintenance
» Replacing the Lamp
After your lamp has been operating for 2000 hours (up to 2500 hours in Eco mode) or longer, the LAMP indicator in the
cabinet will blink red and the message [The lamp has reached the end of its usable life. Please replace the lamp.]
will appear. Even though the lamp may still be working, replace it at 2000 (up to 2500 hours in Eco mode) hours to
maintain optimal projector performance. After replacing the lamp, be sure to clear the lamp hour meter. (→ page 45)
CAUTION
•
DO NOT TOUCH THE LAMP immediately after it has been used. It will be extremely hot. Turn the projector off
and then disconnect the power cable. Allow at least one hour for the lamp to cool before handling.
•
•
DO NOT REMOVE ANY SCREWS except two lamp case screws.You could receive an electric shock.
Do not break the glass on the lamp housing.
Keep finger prints off the glass surface on the lamp housing. Leaving finger prints in the glass surface might
cause an unwanted shadow and poor picture quality.
•
The projector will turn off and go into standby mode after 2100 (up to 2600 hours in Eco mode) hours of service.
If this happens, be sure to replace the lamp. If you continue to use the lamp after 2000 hours (up to 2500 hours
in Eco mode) of use, the lamp bulb may shatter, and pieces of glass may be scattered in the lamp case. Do not
touch them as the pieces of glass may cause injury. If this happens, contact your NEC dealer for lamp replace-
ment.
To replace the lamp:
Optional lamp and tools needed for replacement:
•
•
Replacement lamp LT35LP (LT35) or LT30LP (LT30/LT25)
Phillips screwdriver or equivalent
1. Place the projector on a soft cloth and turn it over to access the lamp cover on the bottom.
2. Loosen the lamp cover screw until the screwdriver goes into a freewheeling condition and remove the
lamp cover.
The lamp cover screw is not removable.
47
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Maintenance
3. Loosen the two screws securing the lamp housing until the phillips screwdriver goes into a freewheeling
condition.The two screws are not removable.
Remove the lamp housing by holding it.
Interlock
PUSH
P
U
S
H
NOTE: There is an interlock on this case to prevent the risk of electrical shock. Do not attempt to circumvent this interlock.
4. Push the part labeled “PUSH” and insert a new lamp housing until the lamp housing is plugged into the
socket.
CAUTION
Do not use a lamp other than the NEC replacement lamp LT35LP (LT35) or LT30LP (LT30/LT25).
Order this from your NEC dealer.
Secure it in place with the two screws.
Be sure to tighten the screws.
P
U
S
H
PUSH
5. Reattach the lamp cover.
6. Tighten the lamp cover screw.
Be sure to tighten the screw.
48
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Maintenance
7. Connect the supplied power cable and turn on the projector.
8. Finally, select the menu → [Reset] → [Clear Lamp Hours] to reset the lamp usage hours.
NOTE: When the lamp exceeds 2100 hours (up to 2600 hours in Eco mode) of service, the projector cannot turn on and the menu is
not displayed.
If this happens, press the HELP button on the remote control for 10 seconds to reset the lamp clock back to zero.
When the lamp time clock is reset to zero, the LAMP indicator goes out.
49
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Appendix
ᕡ Troubleshooting
This section helps you resolve problems you may encounter while setting up or using the projector.
Indicator Messages
Power Indicator
Indicator Condition
Projector Condition
The main power is off
The projector is getting ready to turn on. Wait for a moment.
Note
Off
–
Blinking light
Green
0.5 sec On,
0.5 sec Off
2.5 sec On,
0.5 sec Off
0.5 sec On,
0.5 sec Off
Off Timer is enabled.
–
Orange
The projector is cooling down.
Wait for a moment.
Steady light
Green
The projector is turned on.
The projector is in Standby.
–
–
Orange
Status Indicator
Indicator Condition
Off
Projector Condition
Note
Normal
–
Blinking light
Red
1 cycle (0.5 sec On, Lamp cover error or lamp housing error Replace the lamp cover or lamp
2.5 sec Off)
housing correctly.
2 cycle (0.5 sec On, Temperature error
0.5 sec Off)
The projector is overheated. Move
the projector to a cooler location.
Fans will not work correctly.
4 cycle (0.5 sec On, Fan error
0.5 sec Off)
6 cycle (0.5 sec On, Lamp error
0.5 sec Off)
Lamp fails to light. Wait a full
minute and then turn on again.
Green
Re-firing the lamp (The projector is cool- The projector is re-firing.
ing down.)
Wait for a moment.
Steady light
Orange
Control Panel Lock is on.
You have pressed cabinet button
when Control Panel Lock is on.
Lamp Indicator
Indicator Condition
Projector Condition
Note
Off
Normal
–
Blinking light
Steady light
Red
Lamp has reached its end of life. Lamp Replace the lamp.
replacement message will be displayed.
Lamp has been used beyond its limit. The Replace the lamp.
projector will not turn on until the lamp is
replaced.
Red
Green
Lamp mode is set to Eco mode
–
50
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Appendix
Problem
CheckThese Items
Does not turn on
•
Check that the power cable is plugged in and that the power button on the projector cabinet or the remote
•
•
Check to see if the projector has overheated. If there is insufficient ventilation around the projector or if the
room where you are presenting is particularly warm, move the projector to a cooler location.
Check to see if the lamp usage exceeds 2100 hours (up to 2600 hours : Eco mode). If so, replace the lamp.
•
•
•
•
The lamp may fail to light. Wait a full minute and then turn on the power again.
Will turn off
No picture
Use the VIDEO, the S-VIDEO or the COMPUTER button on the remote control to select your source (Computer,
Ensure your cables are connected properly.
Remove the lens cap.
•
•
•
•
•
•
•
Reset the settings or adjustments to factory preset levels using the [Reset] in the Menu. (→ page 45)
Be sure to connect the projector and notebook PC while the projector is in standby mode and before turning on
the power to the notebook PC.
In most cases the output signal from the notebook PC is not turned on unless connected to the projector
before being powered up.
* If the screen goes blank while using your remote control, it may be the result of the computer's screen-
saver or power management software.
•
•
See also the next page.
Picture suddenly
becomes dark
When one of the following happens, the Lamp mode automatically changes from Normal to Eco.
* When there are no signals (blue or black screen) → To return to the Normal mode, select another available
source.
* When the room where you' re presenting is particularly warm → Move the projector to a cooler location.
Color tone or hue is
unusual
•
•
Check if an appropriate color is selected in [Wall Color]. If not, select an appropriate option. (→ page 40)
Image isn’t square to
the screen
•
•
Picture is blurred
•
•
•
Make sure that focus is appropriate.
Ensure that the distance between the projector and screen is within the adjustment range of the lens. (→ page
•
Make sure that the distance between the focus sensor and the screen is within the effective range of the Auto
•
•
Condensation may form on the lens if the projector is cold, brought into a warm place and is then turned on.
Should this happen, let the projector stand until there is no condensation on the lens.
Image is scrolling
vertically, horizontally
or both
•
•
Use the VIDEO, the S-VIDEO or the COMPUTER button on the remote control to select your source (Video, S-
Adjust the computer image manually with the Horizontal and Vertical in the [Image Options] → [Position/
Remote control does
not work
•
•
•
Make sure there are no obstacles between you and the projector.
Indicator is lit or
blinking
•
Cross color in RGB
mode
•
•
Adjust the computer image manually with [Clock] and [Phase] in [Image Options] → [Position/Clock] in the
For more information contact your dealer.
51
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Appendix
If there is no picture, or the picture is not displayed correctly.
• Power on process for the projector and the PC.
Be sure to connect the projector and notebook PC while the projector is in standby mode and before turning on
the power to the notebook PC.
In most cases the output signal from the notebook PC is not turned on unless connected to the projector before
being powered up.
NOTE: You can check the horizontal frequency of the current signal in the projector’s menu under Information. If it reads “0kHz”,
•
Enabling the computer’s external display.
Displaying an image on the notebook PC’s screen does not necessarily mean it outputs a signal to the projec-
tor. When using a PC compatible laptop, a combination of function keys will enable/disable the external display.
Usually, the combination of the ‘Fn” key along with one of the 12 function keys gets the external display to come
on or off. For example, NEC laptops use Fn + F3, while Dell laptops use Fn + F8 key combinations to toggle
through external display selections.
•
•
Non-standard signal output from the computer
If the output signal from a notebook PC is not an industry standard, the projected image may not be displayed
correctly. Should this happen, deactivate the notebook PC’s LCD screen when the projector display is in use.
Each notebook PC has a different way of deactivate/reactivate the local LCD screens as described in the
previous step. Refer to your computer’s documentation for detailed information.
Image displayed is incorrect when using a Macintosh
When using a Macintosh with the projector, set the DIPswitch of the Mac adapter (not supplied with the projec-
tor) according to your resolution. After setting, restart your Macintosh for the changes to take affect.
For setting display modes other than those supported by your Macintosh and the projector, changing the DIP
switch on a Mac adapter may bounce an image slightly or may display nothing. Should this happen, set the DIP
switch to the 13” fixed mode and then restart your Macintosh. After that, restore the DIP switches to a
displayable mode and then restart the Macintosh again.
NOTE: A Video Adapter cable manufactured by Apple Computer is needed for a PowerBook which does not have a mini D-Sub
15-pin connector.
•
•
Mirroring on a PowerBook
*
When using the projector with a Macintosh PowerBook, output may not be set to 1024 x 768 unless “mirror-
ing” is off on your PowerBook. Refer to owner’s manual supplied with your Macintosh computer for mirroring.
Folders or icons are hidden on the Macintosh screen
Folders or icons may not be seen on the screen. Should this happen, select [View] → [Arrange] from the Apple
menu and arrange icons.
52
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Appendix
ᕢ Specifications
This section provides technical information about the LT35/LT30/LT25 projector's performance.
Model Number
LT35/LT30/LT25
Optical
DMD
Single Chip Digital Micromirror Device (DMD)
Resolution
Lens
1024 x 768 pixels* up to SXGA+ (1400 x 1050) with scaling technology
Manual zoom and auto focus (effective range: 1.4 m - 5.5 m) / manual
focus
F2.4 - 2.6 f=25.7 mm - 30.8 mm
Lamp
LT35: 220W AC (170W Eco mode)
LT30/LT25: 200W AC (170W Eco mode)
30" - 300" diagonal
42" - 438" (wide) - 51" - 524" (tele)
Image Size (Diagonal)
Projection Distance
1.1 - 11.1 m (wide) - 1.3- 13.3 m (tele)
11.6° - 12.1° (wide) / 9.7° - 10.0° (tele)
Projection Angle
Electrical
Inputs
1VGA shared with component video (Mini D-Sub 15 Pin), 1 S-Video (Mini
DIN 4 Pin), 1 Video (RCA), 1 Stereo Mini Audio, 1 PC Control (Mini DIN 8
Pin)
Video Compatibility
Scan Rate
NTSC, NTSC4.43, PAL, PAL-60, PAL-N, PAL-M, SECAM,
Component : 1080i, 720p, 576p, 480p, 576i, 480i
Horizontal: 15 kHz to 100 kHz (RGB: 24 kHz or over)
Vertical: 50 Hz to 85 Hz
Color Reproduction
Horizontal Resolution
16.7 million colors simultaneously, Full color
NTSC / NTSC4.43/PAL / PAL-60/PAL-N/PAL-M/YCbCr: 540 TV lines
SECAM: 300 TV lines
RGB: 1024 dots (H) x 768 dots (V)
External Control
Sync Compatibility
Built-in Speaker
Power Requirement
Input Current
IR, RS232C
Separate Sync / Composite Sync / Sync on G
1W (monaural)
100 - 240V AC, 50 / 60 Hz
LT35: 3.1 - 1.4A
LT30/LT25: 2.8 - 1.3A
Power Consumption
LT35: 280W in Lamp Normal mode, 230W in Lamp Eco mode, 8.0W in
Standby mode
LT30/LT25:260W in Lamp Normal mode, 230W in Lamp Eco mode, 8.0W
in Standby mode
* Effective pixels are more than 99.99%.
53
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Appendix
Mechanical
Installation Orientation
Dimensions
Desktop/Front, Desktop/Rear, Ceiling/Front, Ceiling/Rear
10.2" (W) x 3.5" (H) x 8.2" (D)
260 mm (W) x 89 mm (H) x 208.5 mm (D) (not including protrusions)
4.4 lbs / 2.0 kg
Net Weight
Environmental Considerations Operational Temperatures: 41°F to 104°F / 5°C to 40°C
(Eco mode selected automatically at 95°F to 104°F/35°C to 40°C)
20% to 80% humidity (non-condensing)
Storage Temperatures: 14°F to 122°F (-10°C to 50°C), 20% to 80% hu-
midity (non-condensing)
Regulations
For United States:
UL Approved (UL 60950-1)
Meets FCC Class B requirements
For Canada:
UL Approved (CSA 60950-1)
Meets DOC Canada Class B requirements
For Australia/New Zealand:
Meets AS/NZS CISPR.22 Class B
For Europe:
Meets EMC Directive (EN55022, EN55024, EN61000-3-2, EN61000-3-3)
Meets Low Voltage Directive (EN60950-1, TUV GS Approved)
For additional information visit:
Europe : http://www.neceurope.com/
Global : http://www.nec-pj.com/
The specifications are subject to change without notice.
54
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Appendix
ᕣ Cabinet Dimensions
P C C O N T R O L A U D I O I N
S - V I D E O I N
V I D E O I N
C O M P U T E R I N
F O C U S
A U T O A D J .
S O U R C E
O N / S T A N D B Y
P O W E R
S T A T U S
L A M P
S E L E C T
260 (10.2")
85 (3.3")
Lens center
PUSH
Unit: mm (inch)
55
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Appendix
ᕤ Pin Assignments of D-Sub COMPUTER Input Connector
Mini D-Sub 15 Pin Connector
Pin No. RGB Signal (Analog)
YCbCr Signal
11 12 13 14 15
6
7
8
9
10
1
2
3
Red
Cr
Y
Cb
1
2
3
4
5
Green or Sync on Green
Blue
4
5
6
7
Ground
Ground
Red Ground
Green Ground
Blue Ground
Signal Level
Video signal : 0.7Vp-p (Analog)
Sync signal : TTL level
Cr Ground
Y Ground
Cb Ground
8
9
No Connection
Sync Signal Ground
SCART Sync
Bi-directional DATA (SDA)
Horizontal Sync or Composite Sync
Vertical Sync
Data Clock
10
11
12
13
14
15
56
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Appendix
ᕥ Compatible Input Signal List
Horizontal: 15 kHz to 100 kHz (RGB: 24 kHz or over)
Vertical: 50 Hz to 85 Hz
Signal
Resolution
( Dots )
Frequency H.
( kHz )
Refresh Rate
( Hz )
NTSC
–
15.73
15.63
15.73
15.63
31.47
31.48
35.00
37.86
37.50
39.38
43.27
31.47
35.16
37.88
48.08
46.88
53.67
49.72
48.36
56.48
60.24
60.02
68.68
67.50
61.80
60.00
63.98
69.87
–
60.00
PAL
–
50.00
PAL60
–
60.00
SECAM
VESA
–
50.00
640
ן 480 640
ן 480 640
ן 480 640
ן 480 640
ן 480 640
ן 480 640
ן 480 720
ן 350 800
ן 600 800
ן 600 800
ן 600 800
ן 600 800
ן 600 832
ן 624 1024
ן 768 1024
ן 768 1024
ן 768 1024
ן 768 1024
ן 768 1152
ן 864 1152
ן 900 1280
ן 960 1280
ן 1024 1280
ן 1024 1400
ן 1050 1920
ן 1080 1920
ן 1080 1280
ן 720 1280
ן 720 –
59.94
IBM
59.95
MAC
66.67
VESA
72.81
VESA
75.00
IBM
75.00
VESA
85.01
IBM
70.08
VESA
56.25
VESA
60.32
VESA
72.19
VESA
75.00
VESA
85.06
MAC
74.55
VESA
60.00
VESA
70.07
MAC
74.93
VESA
75.03
VESA
85.00
#
#
#
#
#
#
#
#
#
#
VESA
75.00
SUN
65.95
VESA
60.00
VESA
60.02
MAC
65.18
SXGA+
HDTV (1080i)(1125i)
HDTV (1080i)(1125i)
HDTV (720p)(750p)
HDTV (720p)
SDTV(576p)(625p)
SDTV (480p)(525p)
DVD YCbCr
DVD YCbCr
60.00
33.75
28.13
45.00
37.50
31.25
31.47
15.73
15.63
60.00 Interlace
50.00 Interlace
60.00 Progressive
50.00 Progressive
50.00 Progressive
59.94 Progressive
59.94 Interlaced
50.00 Interlaced
–
–
–
# : Signals above flagged with # are compressed with scaling technology.
NOTE: Signals other than those specified in the table above may not be displayed correctly. If this should happen, change the refresh
rate or resolution on your PC. Refer to Display Properties help section of your PC for procedures.
57
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Appendix
ᕦ PC Control Codes and Cable Connection
PC Control Codes
Function
Code Data
POWER ON
02H
02H
02H
02H
02H
02H
02H
02H
02H
00H
00H
00H
00H
00H
00H
00H
00H
00H
00H
00H
00H
00H
00H
00H
00H
00H
00H
00H
00H
00H
02H
02H
02H
00H
00H
00H
00H
02H
03H
01H
01H
01H
12H
13H
14H
15H
POWER OFF
01H
03H
03H
03H
10H
11H
12H
13H
INPUT SELECT COMPUTER
INPUT SELECT VIDEO
INPUT SELECT S-VIDEO
PICTURE MUTE ON
PICTURE MUTE OFF
SOUND MUTE ON
SOUND MUTE OFF
01H
06H
0BH
09H
0EH
13H
NOTE: Contact your local dealer for a full list of the PC Contorol Codes if needed.
Cable Connection
Communication Protocol
Baud rate ........................................ 38400 bps
Data length ..................................... 8 bits
Parity.............................................. No parity
Stop bit .......................................... One bit
X on/off .......................................... None
Communications procedure ........... Full duplex
NOTE: Depending on the equipment, a lower baud rate may be recommended for long cable runs.
PC Control Connector (DIN-8P)
To TxD of PC
To GND of PC
1
2
4
3
5
6
7
8
To RxD of PC
58
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Appendix
ᕧ Troubleshooting Check List
Before contacting your dealer or service personnel, check the following list to be sure repairs are needed also by
referring to the “Troubleshooting” section in your user’s manual. This checklist below will help us solve your problem
more efficiently.
* Print the following pages.
Frequency of occurrence Ⅺ always Ⅺ sometimes (How often?_____________________) Ⅺ other (__________________)
Power
No power (POWER indicator does not light green) See also “Sta-
tus Indicator (STATUS)”.
Shut down during operation.
Power cable's plug is fully inserted into the wall outlet.
Lamp cover is installed correctly .
Power cable's plug is fully inserted into the wall outlet.
The power cable has been unplugged and plugged quickly dur-
ing projection.
Power Management is turned off (only models with the Power
Management function).
Lamp cover is installed correctly .
Off Timer is turned off (only models with the Off Timer func-
tion ).
Lamp Hour Used (lamp operation hours) was cleared after lamp
replacement.
No power even though you press and hold the POWER button
for a minimum of 1 second.
Video and Audio
No image is displayed from your PC or video equipment to the
projector.
Parts of the image are lost.
Still unchanged even though you press the AUTO ADJ. button.
Still no image even though you connect the projector to the PC
first, then start the PC.
Still unchanged even though you carry out [Reset] in the
projector’s menu.
Enabling your notebook PC’s signal output to the projector.
•
A combination of function keys will enable/disable the ex-
ternal display. Usually, the combination of the “Fn” key along
with one of the 12 function keys turns the external display
on or off.
Image is shifted in the vertical or horizontal direction.
Horizontal and vertical positions are correctly adjusted on a
computer signal.
Input source's resolution and frequency are supported by the
projector.
No image (blue background, black background).
Still no image even though you press the AUTO ADJ. button.
Some pixels are lost.
Image is flickering.
Still no image even though you carry out [Reset] in the
projector’s menu.
Still unchanged even though you press the AUTO ADJ. button.
Signal cable's plug is fully inserted into the input connector
Still unchanged even though you carry out [Reset] in the
projector’s menu.
A message appears on the screen.
( _____________________________________________ )
Image shows flickering or color drift on a computer signal.
The source connected to the projector is active and available.
Still no image even though you adjust the brightness and/or
the contrast.
Image appears blurry or out of focus.
Auto Focus is turned on.
Input source's resolution and frequency are supported by the
projector.
There are no objections between the focus sensor and the
screen.
The throw distance is within 1.4 to 5.5 m/55.1” to 216.5”
Image is projected onto the screen.
Image is too dark.
Remains unchanged even though you adjust the brightness
and/or the contrast.
Image is distorted.
Still unchanged even though you adjusted the focus manually.
No sound.
Audio cable is correctly connected to the audio input of the
projector.
Image appears to be trapezoidal (unchanged even though you
carry out the [Keystone] adjustment).
Still unchanged even though you adjusted the volume level.
Other
Remote control does not work.
Buttons on the projector cabinet do not work ( only models with
the Key Lock function).
No obstacles between the sensor of the projector and the re-
mote control.
Control Panel Lock is not turned on or is disabled in the menu.
Projector is placed near a fluorescent light that can disturb the
infrared remote controls.
Still unchanged even though you press and hold the EXIT but-
ton for a minimum of 10 seconds.
Batteries are new and are not reversed in installation.
59
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Appendix
In the space below please describe your problem in detail.
Information on application and environment where your projector is used
Projector
Installation environment
Screen size:
Model number:
inch
Serial No.:
Screen type: Ⅺ White matte Ⅺ Beads Ⅺ Polarization
Ⅺ Wide angle Ⅺ High contrast
Date of purchase:
Lamp operating time (hours):
Lamp Mode:
Throw distance:
feet/inch/m
Ⅺ Normal Ⅺ Eco
Orientation: Ⅺ Ceiling mount Ⅺ Desktop
Power outlet connection:
Information on input signal:
Horizontal synch frequency
Vertical synch frequency
Synch polarity
[
[
] kHz
] Hz
Ⅺ Connected directly to wall outlet
Ⅺ Connected to power cord extender or other (the num-
ber of connected equipment______________)
H Ⅺ (+) Ⅺ (–)
Ⅺ Connected to a power cord reel or other (the number
V Ⅺ (+) Ⅺ (–)
of connected equipment______________)
Synch type
Ⅺ Separate Ⅺ Composite
Ⅺ Sync on Green
Computer
STATUS Indicator:
Steady light
Manufacturer:
Ⅺ Orange Ⅺ Green
Model number:
Notebook PC Ⅺ / Desktop Ⅺ
Native resolution:
Refresh rate:
Flashing light
[
] cycles
Remote control model number:
Video adapter:
Other:
PC
Projector
DVD player
Video equipment
Signal cable
VCR, DVD player, Video camera, Video game or other
NEC standard or other manufacturer’s cable?
Model number:
Distribution amplifier
Model number:
Switcher
Length:
inch/m
Manufacturer:
Model number:
Model number:
Adapter
Model number:
60
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Appendix
5) Problems or damage caused by use in hot or humid places, in
vehicles, boats or ships, etc.
ᕨ TravelCare Guide
6) Problems or damage caused by expendable supplies or devices
connected to the product other than those designated by NEC.
TravelCare - a service for international travelers
This product is eligible for "TravelCare", NEC's unique international war-
ranty.
Please note that TravelCare coverage differs in part from coverage un-
der the warranty included with the product.
7) Problems caused by natural consumption, wear or deterioration
of parts under normal usage conditions.
8) Problems or damage to lamps and other expendable supplies,
included parts or optional parts.
Services offered with TravelCare
9) Other conditions stipulated in the warranty included with the prod-
uct also apply.
This warranty allows customers to receive service on their product at
the NEC and NEC-designated service stations in the countries listed
herein when temporarily traveling internationally for business or plea-
sure.
For details on services offered by the different service stations, please
refer to the "List of TravelCare Outlets" below.
NOTE: The product can be used overseas with voltages of 100 to 120V and 200
to 240V by using a power cable suited for the standards and power source volt-
age of the country in which the product is being used.
List of TravelCare Outlets
1 Repair services
The product will be repaired and delivered within 10 business days,
This list applies as of December 1, 2004.
For the most up-to-date information, please refer to the websites of the
service stations in the various countries on the List of TravelCare Out-
not including shipping time.
During the term of warranty, the cost of maintenance parts, labor
costs for repairs and shipping costs within the service station's cov-
erage area are covered by the warranty.
In Europe
NEC Europe, Ltd. / European Technical Centre
2 Replacement product rental service
If the customer desires, he or she can rent a replacement product
while the original product is being repaired.
Fee: US$200 for 12 days
This fee must be paid at the local service station in cash or credit
card.
Address:
Telephone:
Fax Line:
Unit G, Stafford Park 12, Telford TF3 3BJ, U.K.
+44 1952 237000
+44 1952 237006
Email Address:
WEB Address:
The $200 rental fee is non-refundable even if the customer rents it
less than 12 days before returning.
(Regions Covered)
EU:
Austria*, Belgium*, Denmark*, Finland*, France*, Germany*,
Greece*, Ireland*, Italy*, Luxembourg*, The Netherlands*,
Portugal*, Spain*, Sweden* and the United Kingdom*
Norway*, Iceland and Liechtenstein
The replacement product will be delivered within 3 business days.
If the customer did not return the replacement product within 12 days,
the customer will be charged the price of the unit.
If the customer returned the replacement product in a faulty or dam-
aged condition, the repair cost will be charged to the customer.
Note that this service is not offered in all countries and regions. Please
refer to the "List of TravelCare Outlets".
EEA:
In North America
NEC Solutions (America), Inc.
Address:
1250 N. Arlington Heights Road,
In addition, this replacement product rental service is not offered af-
ter the product's warranty has expired.
Itasca, Illinois 60143, U.S.A.
+1 800 836 0655
+1 800 356 2415
Telephone:
Fax Line:
Term of warranty
Email Address: [email protected]
WEB Address: http://www.necvisualsystems.com
1
a. Upon presentation of the warranty or receipt received upon pur-
chase:
(Regions Covered)
U.S.A. *, Canada*
Valid for the term indicated on the warranty or the normal term of
warranty for the country of purchase.
In Oceania
b. When only the product is brought in:
NEC Australia Pty., Ltd.
Address: New South Wales;
184 Milperra Road, Reversby 2212
Victoria;
Valid for a period of within 14 months of the date of manufacture
indicated by the serial number attached to the product.
2 When a product whose term of warranty is expired is brought in:
480 Princess Hwy Noble Park 3174
South Australia;
84A Richmond Road, Keswick 5035
Queensland;
116 Ipswich Road, Woollongabba 4102
Western Australia;
Repairs will be offered for a fee. In this case the customer is not
eligible for the replacement product rental service.
3 In the following cases, repairs may be charged, even if the product's
warranty is still in effect:
1) If the term of warranty, model name, serial number and name of
the store of purchase are not indicated on the warranty or have
been altered.
45 Sarich Court Osborne Park 6017
Telephone:
131 632 (from domestic)
+61 8 8375 5706 (from overseas)
+61 8 8375 5757
2) Problems or damage caused by dropping or shocks during ship-
ment or movement by the customer or by improper handling by
the customers.
Fax Line:
Email Address: [email protected]
WEB Address: http://www.nec.com.au
3) Problems or damage caused by improper usage or unwarrant-
able alterations or repairs by the customer.
(Regions Covered)
Australia*, New Zealand
4) Problems or damage caused by fire, salt damage, gas damage,
earthquakes, lightning damage, storm or flood damage or other
natural disasters or such external factors as dust, cigarette
smoke, abnormal voltage, etc.
61
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Appendix
In Asia and Middle East
Lenso Communication Co., Ltd.
NEC Viewtechnology, Ltd.
Address:
292 Lenso House 4, 1st Floor, Srinakarin Road,
Huamark, Bangkapi, Bangkok 10240, Thailand
+66 2 375 2425
Address:
686-1, Nishioi, Oi-Machi, Ashigarakami-Gun,
Kanagawa 258-0017, Japan
+81 465 85 2369
Telephone:
Fax Line:
Telephone:
+66 2 375 2434
Fax Line:
Email Address:
WEB Address:
+81 465 85 2393
Email Address:
WEB Address:
(Regions Covered)
Thailand
(Regions Covered)
Japan*
ABBA Electronics L.L.C.
Address:
NEC Hong Kong Ltd.
Address:
Tariq Bin Ziyad Road, P.O.Box 327, Dubai,
United Arab Emirates
+971 4 371800
11th Floor, Tower B, New Mandarin Plaza, 14
Science Museum Road,
Tsim Sha Tsui East, Kowloon, Hong Kong
+852 2369 0335
Telephone:
Fax Line:
+971 4 364283
Telephone:
Email Address:
Fax Line:
+852 2795 6618
Email Address:
WEB Address:
(Regions Covered)
United Arab Emirates
(Regions Covered)
Hong Kong
Samir Photographic Supplies
Address:
P.O.Box 599, Jeddah 21421, Saudi Arabia
Telephone:
Fax Line:
Email Address:
+966 2 6828219
+966 2 6830820
NEC Taiwan Ltd.
Address:
7F, No.167, SEC.2, Nan King East Road, Taipei,
Taiwan, R.O.C.
Telephone:
Fax Line:
+886 2 8500 1734
+886 2 8500 1420
(Regions Covered)
Saudi Arabia
Email Address:
WEB Address:
NOTE: In countries designated with an asterisk(*), replacement product rental
service are offered.
(Regions Covered)
Taiwan
NEC Solutions Asia Pacific Pte. Ltd
Address:
401 Commonwealth Drive, #07-02, Haw Par
Technocentre, Singapore 149598
+65 6 273 8333
Telephone:
Fax Line:
+65 6 274 2226
Email Address:
WEB Address:
(Regions Covered)
Singapore
NEC Systems Integration Malaysia Sdn Bhd
Address:
Ground Floor, Menara TA One, 22, Jalan P. Ramlee,
50250 Kuala Lumpur, Malaysia
+6 03 2164 1199
Telephone:
Fax Line:
+6 03 2160 3900
Email Address:
WEB Address:
(Regions Covered)
Malaysia
Tele Service Co., Ltd.
Address:
2nd Fl., Ire B/D. #2, 4Ga, Yangpyeng-Dong,
Youngdeungpo-Gu, Seoul, Korea 150-967
+82 2 2163 4193
Telephone:
Fax Line:
+82 2 2163 4196
Email Address:
(Regions Covered)
South Korea
62
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Appendix
P-1/
,
Date:
/
/
,
TO: NEC or NEC's Authorized Service Station:
FM:
(Company & Name with signature)
Dear Sir (s),
I would like to apply your TravelCare Service Program based on attached registration and qualification sheet and agree with your
following conditions, and also the Service fee will be charged to my credit card account, if I don't return the Loan units within the
specified period. I also confirm following information is correct. Regards.
Application Sheet for TravelCare Service Program
Country,
product purchased :
User's Company Name :
User's Company Address :
Phone No., Fax No. :
User's Name :
User's Address :
Phone No., Fax No. :
Local Contact office :
Local Contact office Address :
Phone No., Fax No. :
User's Model Name :
Date of Purchase :
Serial No. on cabinet :
Problem of units per User :
Required Service :
(1) Repair and Return
(1) Credit Card
(2) Loan unit
Requested period of Loan unit :
Payment method :
(2) Travelers Cheque
(3) Cash
In Case of Credit Card :
Card No. w/Valid Date :
63
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Appendix
5. Loan Service Charges and Conditions:
Upon acceptance of this NEC Projector, Customer agrees to assume
liability for this loan unit.
Condition of your TravelCare Service Program
Enduser is requested to understand following condition of TravelCare
Service Program and complete the necessary information on the appli-
cation sheet.
The current cost of use of this loan unit is $200.00 USD for 12 calendar
days.
1. Service Options:
There are 3 types of "Service" available. Enduser has to understand
following condition and is required to fill in the Application Sheet.
If Customer does not return the unit within the 12 calendar days, Cus-
tomer will be charged the next highest cost up to and including the full
list price to Credit Cards, which price will be informed by NEC Autho-
rized Service Stations. Please see the attached listing of contacts for
each country to arrange for pickup of the loan unit.
1) Repair and Return:
The 'Faulty unit' is sent or collected from the customer. It is repaired
and returned within 10 days to the customer, excluding transport time.
If you return to their country of origin with the loan unit, you will be
charged additional freight to return the unit to the loaning country.
There may have a case, repair and return can't be done by NEC
Authorized Service Station, because of shortage of spare parts due
to same model is not sold in the territory.
Thank you for your understanding of this program.
2) Repair and Return with Loan: (This service is limited to some Ser-
vice Stations)
This service is offered to the Enduser, who cannot wait until their unit
is repaired.
The customer can borrow a unit for $200 up to 12 days. Customer
then sends in inoperable unit to nearest NEC Authorized Service
Station for service. In order to prevent collection problem, Enduser is
required to fill in Application Sheet.
Enduser needs to confirm the availability of the Service to NEC Au-
thorized Service Stations.
3) Loan Only:
For this service, NEC Authorized Service Station supplies the cus-
tomer with a loan unit for US$200 up to 12 days.Customer keeps the
inoperable unit and when customer returns home, customer arranges
to have the projector serviced in the home country.
2. Warranty Exclusions:
This program does not apply if the Projector's serial number has been
defaced, modified or removed.
If, in the judgement of NEC Authorized Service Station or its agent the
defects or failures result from any cause other than fair wear and tear or
NEC neglect, or fault including the following without limitation:
1) Accidents, transportation, neglect, misuse, abuse, water, dust, smoke
or default of or by the Customer its employees or agents or any third
party;
2) Failure or fluctuation of electrical power, electrical circuitry, air condi-
tioning, humidity control or other environmental conditions such as
use it in smoking area;
3) Any fault in the attachments or associated products or components
(whether or not supplied by NEC or its agents which do not form part
of the Product covered by this warranty);
4) Any act of God, fire, flood, war, act of violence or any similar occur-
rence;
5) Any attempt by any person other than any person authorized by NEC
to adjust, modify, repair, install or service the product.
6) Any Cross-border charges such as, duty, insurance, tax etc.
3. Charges for Warranty Exclusions and Out of Warranty Case:
In case faulty unit is under warranty exclusions case or under Out of
Warranty period, NEC Authorized Service Station will Inform estimation
of actual service cost to the Enduser with reason.
4. Dead on Arrival (DOA):
Enduser must take this issue up with their original supplier in the coun-
try of purchase.
NEC Authorized Service Station will repair the DOA unit as a Warranty
repair, but will not exchange DOA unit with new units.
Ver. 1 09/05
64
Download from Www.Somanuals.com. All Manuals Search And Download.
|