INSTALLATION MANUAL
JET TANK SYSTEM
EASTERN
STANDARD
TIME
CONSUMER HOT-LINE: 1-800-942-3343 • MONDAY - FRIDAY • 7 AM to 5 PM
JET TANK
®
R
SYSTEM
pump only
with 7-gallon
diaphragm
pressure
tank
MODEL R-30-T7
1/3 Horse Power
Convertible Pump
WARRANTY
PRODUCT DEFECTS
COVERED TWELVE
MONTHS FROM
DATE OF PURCHASE
OR EIGHTEEN
MONTHS FROM
DATE OF MANUFAC-
TURE, WHICHEVER
COMES FIRST. RE-
CEIPT AND PROD-
UCT DATE CODE
REQUIRED FOR
WARRANTY CLAIM.
WATER ACE PUMP COMPANY • ASHLAND, OHIO 44805-1969
23833A343
Download from Www.Somanuals.com. All Manuals Search And Download.
FINDING THE DEPTH OF YOUR WELL
IMPORTANT SELECT
CORRECT VOLTAGE
The jet tank system installs differently depending
on the depth of your well. Tie a small but heavy
weight to the end of a piece of string (be sure there is
enough string; some wells are very deep). Lower the
weight into the well until it reaches the bottom. Take up
the slack and mark the string at ground level. Pull the
weight out of the well and measure from the bottom of
the weight to the ground level mark. This is the depth
of your well. Subtract five feet from the depth of your
well. This number should not exceed the maximum
rated depth for your pump. If it does, it will greatly
hinder or prevent the proper operation of the pump.
GRD
VOLTAGE SELECTOR
AT REAR OF MOTOR
(USE NEEDLE
UNGROUNDED
LINE
NOSE PLIERS)
230V
115V
PULL SELECTOR -
ROTATE - REINSERT
L1
L2
HIGH
LOW
VOLTAGE VOLTAGE
230
VOLTAGE
SELECTOR
TERMINAL BOARD
115
115V OR 230V OPERATION
USE COPPER CONDUCTORS ONLY
Your pump is equipped with one of two types of dual
voltage motors. Follow the instructions to wire the
motor for the proper voltage. The voltage of the pump
must match the voltage of the power supply.
WIRE SELECTION GUIDE
WIRING YOUR PUMP
Remove the cover from the pressure switch. Connect
the bare copper ground to the ground screw in the
pressure switch. Connect the power supply to the
terminals marked "Line" in the diagram below.
NAME
VOLTAGE PLATE
AMPS
MAX. WIRE LENGTH USING AWG SIZE
#14
#8
#12
#10
115
230
10.6
5.3
118
189
296
464
475
756
1184
1857
LINE
FUSE AND CIRCUIT
BREAKER SIZE GUIDE
MOTOR
LOW PEAK - CART. TYPE
FUSETRON - CART. TYPE
FUSTAT - PLUG TYPE*
STANDARD LINE
PLUG FUSE*
CIRCUIT BREAKER
MOTOR
LINE
115V
230V
115V
230V
115V
230V
20
10
12
6-1/4
20
15
GROUND
*For circuits not over 150 volts to ground.
23833A343
3
Download from Www.Somanuals.com. All Manuals Search And Download.
DRAINING FOR SERVICING OR FOR WINTER
PIPING
The pump should be drained before it is disconnected
for servicing or if it is in danger of freezing. To drain:
• Remove drain plug from bottom of pump case.
• Remove discharge tee to vent the pump.
Plastic PVC pipe is shown in the illustrations, but
galvanized steel pipe may be used if desired. All piping
must be clean and free of all foreign matter to prevent
clogging. ALL JOINTS AND CONNECTIONS IN THE
WELL ASSEMBLY MUST BE AIRTIGHT. Even a pin-
hole leak will prevent the proper operation of the pump
(this is the most common problem). Use thread com-
pound on all threaded joints unless specified otherwise.
• Drain all piping to a point 3 feet below ground level.
SHALLOW WELL PUMP INSTALLATION (4" DIAMETER CASED WELL)
For wells 25 feet or less in depth, the ejector may be
attached to the front of the tank-mounted jet pump. For
lower depths, the ejector must be placed down inside
the well (see DEEP WELL PUMP INSTALLATION). All
materials with part numbers are quality Water Ace parts.
• One can PVC cement (read instructions carefully)
• One can thread compound (read instructions carefully)
• Two male 1-1/4" PVC adapters
• Enough rigid 1-1/4" PVC pipe and couplings to reach
from bottom of well to pump.
• One 4" well seal #RWS4-1012 with vent plug
• One 1-1/4" PVC elbow
General Materials
• One Jet Tank System #R-30-T7. Includes: 1/3 HP
jet pump mounted on a 7-gallon diaphragm pressure
tank, pressure gauge, and twin ejector with gasket,
bolts, venturi tubes, and foot valve.
Tools Needed for all pump installations
Pipe wrench, pipe clamp, crescent wrench, slot screw-
driver, 24-tooth hacksaw, knife or round file.
REMINDER: ALL JOINTS AND CONNECTIONS MUST BE AIRTIGHT. A SINGLE PIN-
HOLE LEAK WILL PREVENT THE PROPER OPERATION OF THE PUMP. USE THREAD
COMPOUND ON ALL THREADED CONNECTIONS UNLESS SPECIFIED OTHERWISE.
S3TEP Cement as many coup-
S1TEP Thread 1-1/4" male PVC
lings and sections of
rigid PVC pipe as it
adapter into foot valve.
Hand tighten, then tighten
1/4 turn with crescent
wrench.
1-1/4"
MALE PVC
ADAPTER
takes to equal the depth
of your well minus five
feet, then firmly clamp
the assembly with a
pipe clamp to prevent
assembly from sliding
down into the well.
FOOT
VALVE
Subtract five feet from the
depth of your well (See
page 3 "Finding the Depth
of Your Well"). This is the
S2TEP
PVC
PIPE
SECTION
total length of rigid PVC pipe and
couplings to cement onto the 1-1/4"
male PVC adapter. Cement one
section of rigid PVC pipe to the PVC
adapter which is connected to the
foot valve, then lower the whole
assembly into the well, foot valve
first. Firmly clamp the end of the
rigid PVC pipe with a pipe clamp to
prevent the assembly from sliding
down into the well.
1-1/4"
MALE PVC
ADAPTER
FOOT
VALVE
23833A343
4
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 9
Remove pipe clamp and
slide Well Seal #RWS4-12
over PVC pipe and onto well
casing. Position assembly
maximum water flow is obtained without
pressure dropping to zero. If pressure falls
completely, retighten adjustment screw and
read-just. Steady pressure must not be less
S4TEP
CONT'D
APPROX.
12" OF
PVC PIPE
PROTRUDING
FROM WELL
SEAL
than 24 lbs. for the R520. If no pressure shows:
Stop motor, remove pressure gauge plug from pressure
regulator, add more water, and try again.
so twelve inches of PVC pipe pro-
trude from well seal. Alternately turn
bolts on well seal counterclockwise
until rubber gaskets are tight against
well casing and PVC pipe.
WELL
SEAL
#RWS4-12
Thread pressure
gauge plug back
STEP
into discharge
tee. Thread
pressure gauge into pres-
sure gauge plug. Make
sure all connections are
tightly sealed. Place a
large basin beneath dia-
phragm tank outlet. Start
motor. If pump is off-set
from well 4 feet or more, it
may take a few minutes
for pump to prime. Failure to prime in 5 minutes:
Stop motor, remove pressure gauge plug from dis-
charge tee, add more water, try again. Allow pump to
run long enough to clear the well of sand or dirt and to
insure well will not run dry. Stop motor.
Cement 1-1/4" PVC elbow
onto PVC pipe protruding
from well seal. If desired,
STEP
10
1-1/4"
PVC
ELBOW
5
some length may be cut off
of PVC pipe before cementing
elbow. Smooth inside of any cut
PVC pipe with file or knife.
TOP OF
PVC PIPE
PROTRUDING
FROM WELL
SEAL
Open ejector
pack included
VENTURI
TUBE
S6TEP
BOLTS
GASKET
EJECTOR
with your jet sys-
tem. The ejector
has two holes in its top.
Thread the venturi tube
(part #25881A281 stamped on the side) into larger hole
until snug. Put gasket over venturi tube so openings in
gasket line up with openings in ejector.
Connect the 1" tank outlet to the service line.
Total installation should look like the drawing
below.
STEP
Secure ejector and
gasket to front of tank-
mounted pump with
bolts provided. Thread
a 1-1/14" male PVC
adapter into front of
ejector.
S7TEP
11
EJECTOR
MALE PVC
ADAPTER
Cement as much PVC pipe and couplings
needed to connect PVC elbow to male PVC
adapter in front of ejector. The diaphragm
pressure tank is preset to 30 PSI. Reset
pressure to 18 PSI using a tire gauge. This is vital to
proper operation of the system.
S8TEP
COMPLETE
SHALLOW WELL
INSTALLATION
Place a large bucket
beneath the pressure
regulator outlet. Start
STEP
PRESSURE
PRESSURE
REGULATOR
GAUGE
ADJUSTMENT
9
motor. Turn regulator
adjustment screw down tight.
If pump is properly primed a
high pressure will immediately
show on the pressure gauge.
With pump operating at high
pressure, slowly unscrew reg-
ulator adjustment screw until
23833A343
5
Download from Www.Somanuals.com. All Manuals Search And Download.
DEEP WELL PUMP INSTALLATION (4" DIAMETER CASED WELL)
• One 1-1/4" close nipple
• One 1" x 4" nipple
• One 1-1/4" x 5" nipple
• Two 1" female PVC adapters
• One 1" male PVC adapter
• Two 1-1/4" male PVC adapters
• Enough rigid 1-1/4" PVC pipe and couplings to reach
from bottom of well to pump (delivery pipe)
• Enough rigid 1" PVC pipe and couplings to reach
from bottom of well to pump (pressure pipe))
• One well seal #RWS4-1012
For wells over 25, but not exceeding 60 feet in depth,
the twin ejector must be installed down inside the well
rather than attached to the front of the pump. Materials
with part numbers are quality Water Ace parts.
General Materials
• One Jet Tank System #R-30-T7. Includes: 1/3 HP
jet pump mounted on a 7-gallon diaphragm pressure
tank, pressure gauge, and twin ejector with
gasket, bolts, venturi tubes, and foot valve.
• One can PVC cement (read instructions carefully)
• One can thread compound (read instructions carefully)
• One 1-1/4" PVC elbow
• One 1" PVC elbow
REMINDER: ALL JOINTS AND CONNECTIONS MUST BE AIRTIGHT. A SINGLE PIN-
HOLE LEAK WILL PREVENT THE PROPER OPERATION OF THE PUMP. USE THREAD
COMPOUND ON ALL THREADED CONNECTIONS UNLESS SPECIFIED OTHERWISE.
Lower the assembly into
S1TEP Thread 1-1/4" close nipple
S5TEP
into foot valve. Thread the
the well, foot valve first.
Use a pipe clamp to
prevent assembly for
sliding down into well.
Cement as many
couplings and sections
of rigid PVC pipe on
both sides of ejector as
it takes to equal the
depth of your well minus
five feet, then firmly
clamp assembly with a
pipe clamp to prevent it
from sliding down into
the well.
EJECTOR
other end of 1-1/4" close
nipple into bottom of twin
ejector. Hand tighten, then
tighten 1/4 turn with pipe
wrench.
1-1/4"
CLOSE
NIPPLE
FOOT
VALVE
The ejector has two holes in
the top of it. Thread venturi
tube (part #25881A281
stamped on the side) into
S2TEP
1" X 5"
NIPPLE
larger hole until snug. Thread 1" x
5" nipple into smaller hole. Only
hand tighten venturi tube. Tighten
nipple 1/4 turn with pipe wrench.
VENTURI
TUBE
EJECTOR
Thread a 1-1/4" male PVC
adapter over the venturi
tube and into ejector.
Thread a 1" female PVC
adapter onto 1" x 5" nipple.
Tighten adapters 1/4 turn
with crescent wrench.
S3TEP
1" FEMALE
PVC
ADAPTER
1-1/4" MALE
PVC
ADAPTER
Remove pipe clamp and
slide well seal #RWS4-1012
over PVC pipes and onto
well casing. DO NOT let
S6TEP
12" OF
PVC PIPE
PROTRUD-
ING FROM
WELL
Subtract five feet from the
depth of your well. This is
the total length of PVC pipe
STEP
1"
PVC
PIPE
1-1/4"
PVC
PIPE
SEAL
assembly slide down into well. Posi-
tion assembly so that twelve inches
of PVC pipes protrude from well
seal. Using crescent wrench, turn
bolts on well seal counterclockwise
until rubber gaskets are tight against
the well casing and the PVC pipes.
4
and couplings to cement
onto both the 1-1/4" male and 1"
female PVC adapters. Cement a
section of PVC pipe to each adapter.
WELL SEAL
#RWS4-1212
23833A343
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Cut 1" pipe 2" shorter than
the 1-1/4" pipe. Smooth
rough edges. Cement 1"
and 1-1/4" PVC elbows to
pipes protruding from the
well seal.
STEP
1-1/4" PVC
ELBOW
1" PVC
ELBOW
7
1" PIPE 2"
SHORTER
THAN 1-1/4"
PIPE
Thread 1-1/4" male PVC
adapter into top hole in front
of tank-mounted pump.
Thread 1" x 4" nipple into
bottom hole in front of pump.
STEP
1 1/4" MALE
PVC
ADAPTER
8
1" x 4"
NIPPLE
Thread the 1" female PVC
adapter onto the 1" x 4"
nipple.
STEP
1 1/4"
FEMALE
PVC
COMPLETE
DEEP WELL
INSTALLATION
9
ADAPTER
STEP
10
1 1/4" PVC PIPE
Cement as
many sec-
tions and
1" PVC PIPE
CAUTION: If you change pressure switch settings,
set the cut-off pressure low enough to shut off the
pump. The recommended pressure is 2 PSI below
your pump cut-off pressure. Example: if a 20-40 PSI
pressure switch is being used, tank pressure should
be 18 PSI. If a valve shuts off and the cut-off setting
is too high, the pump will run continuously without
water flow causing overheating and serious damage.
couplings of
rigid 1" and
1-1/4" PVC pipe needed to connect the 1" female PVC
adapter and the 1-1/4" male PVC adapter to the 1" and
1-1/4" PVC elbows. The diaphragm pressure tank is
factory preset to 30 PSI. Reset the pressure to 18
PSI using a tire gauge. This is vital to the proper
operation of the system. Remove pressure gauge plug.
Place a large bucket
beneath the pressure
regulator outlet. Start
motor. Turn regulator
STEP
REGULATOR
ADJUSTMENT
SCREW
11
adjustment screw down tight.
If pump is properly primed a
high pressure will immediately
show on the pressure gauge.
With pump operating at high
pressure, slowly unscrew reg-
ulator adjustment screw until
maximum water flow is obtain-
ed without pressure dropping to zero. If pressure falls
completely, retighten adjustment screw and re-adjust.
Steady pressure must not be less than 24 lbs. for the
R520 and 32 lbs. for the R100. If no pressure shows:
Stop motor, remove pressure gauge plug from pressure
regulator, add more water, and try again. Complete
installation should look like the drawing to the right.
23833A343
7
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING CHECKLIST
(CAUTION: SHUT OFF POWER TO PUMP)
PROBLEM
POSSIBLE CAUSES
• Not enough water. Stop motor, remove pressure gauge plug, and fill case with water.
• Pump wired incorrectly.
• Plugged venturi tube or nozzle.
Pump will not prime
• Foot valve is sitting in sand or mud, or is stuck shut, or leaks.
• Low well water level. In deep wells, the ejector as well as the foot valve must be below
water level.
• Leaks. Check all connections for airtightness.
• Low well water level. Use a water-level tester while pump is operating.
• Plugged venturi tube, nozzle, or impeller parts.
Pump delivers water
for a period of time,
then stops pumping
• Plugged venturi or nozzle.
• Faulty pressure gauge resulting in false readings.
• In deep wells, the operating pressure may be too high.
• Low well water level. Use a water-level tester while pump is operating.
• Over-submergence of ejector. In deep wells, if ejector is more than 10 feet below
pumping level, pumping capacity is reduced.
Pump does not de-
liver rated capacity
• In deep wells, the ejector may have improper size and depth setting.
• Motor voltage does not match power supply voltage. See pages 2 and 3.
• Improper wire size. See Wire Size Guide on page 3.
• Impeller is rubbing against pump case.
Motor overheats and
shuts off (overload)
• Impeller neck is worn.
• Defective pressure switch.
• The tube connecting the two brass fittings may be clogged.
• Tank precharge pressure too high. Tank precharge pressure must be 1-2 pounds less
than switch turn-on setting.
Pump delivers water
but will not shut off
• In deep wells, the water level may be going below limit of ejector. Use water-level
tester while pump is operating.
Pressure switch
turns on and off
every few seconds
• Galvanized storage tank is waterlogged.
• Leaky foot valve.
• Too much tank pressure.
Motor fails or does
not operate properly
• If within Warranty, return pump/motor unit to place of purchase (with proof of purchase)
for exchange.
LIMITED WARRANTY
WATER ACE PUMP CO. will repair or replace for the original user any portion of a new
Water Ace product which proves defective due to materials or workmanship of WATER ACE
PUMP CO. Contact the nearest authorized WATER ACE PUMP CO. dealer for warranty
service. WATER ACE PUMP CO. shall possess the sole right to determine whether to repair
or replace defective equipment, parts or components. THIS WARRANTY DOES NOT
COVER DAMAGE DUE TO LIGHTNING OR OTHER CONDITIONS BEYOND THE
CONTROL OF WATER ACE PUMP CO.
PRODUCT IMPROVEMENTS: WATER ACE PUMP CO. reserves the right to change or
improve its products or any component without obligation to provide such a change or
improvement for units previously sold and/or shipped.
WARRANTY EXCLUSIONS: After the expiration of this warranty period, THERE WILL BE
NO WARRANTIES INCLUDING ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR
FITNESS FOR ANY PARTICULAR PURPOSE ON ANY SPECIFIC WATER ACE PUMP
PRODUCT. Some states do not allow limitations on how long an implied warranty lasts, so
the above limitation may not apply to you. No warranties or representations at any time
made by any representative of WATER ACE PUMP CO. shall vary or expand the provisions
hereof.
PUMPS: Warranted 12 months from date of purchase or 18 months from date of
manufacture, whichever occurs first. Receipt and product date code required for warranty
claim.
LABOR & COSTS: WATER ACE PUMP CO. shall IN NO EVENT be liable for the cost of
field labor or other charges incurred by any customer in removing and/or reaffixing any
WATER ACE PUMP product. part or component.
LIABILITY LIMITATION: IN NO EVENT SHALL WATER ACE PUMP CO. BE LIABLE FOR
CONSEQUENTIAL, INCIDENTAL OR SPECIAL DAMAGES RESULTING FROM OR
RELATED IN ANY MANNER TO ANY WATER ACE PUMP PRODUCT OR PARTS. Some
states do not allow the exclusion or limitation of incidental or consequential damages, so the
above limitation may not apply to you. This Warranty gives you specific legal rights. You
may have other rights which vary from state to state. In the absence of suitable proof of
purchase date, the effective date of this warranty will be based upon the date of manufacture
plus 180 days.
THIS WARRANTY WILL NOT APPLY: (a) to defects or malfunctions resulting from failure to
properly install, operate, or maintain the unit in accordance with printed instructions provided;
(b) to failures resulting from abuse, accident, or negligence; (c) to normal maintenance
services and the parts used in connection with such service; (d) to units which are not
installed in accordance with applicable local codes, ordinances, and good trade practices; (e)
if the unit is moved from its original installation location; (f) if unit is used for purposes other
than for what it was designed and manufactured.
Direct all Notices, etc. to: Product Warranty and Return Dept., WATER ACE PUMP CO., 1101
Myers Parkway, Ashland, OH 44805-1969
23833A343
Water Ace Pump Co. • 1101 Myers Parkway • Ashland, Ohio 44805-1969
7/95
Download from Www.Somanuals.com. All Manuals Search And Download.
REPLACEMENT PARTS
1
12
2
3 25
4
16
17
14
24
21
23
15
18
9
13, 19, 20
10
11
16
7
JET TANK SYSTEM
MODEL R-30-T7
22
REF.
NO.
REF.
NO.
PART NUMBER
DESCRIPTION
PART NUMBER
DESCRIPTION
1
2
3
4
5
6
7
8
9
20929D501
05003A000
24349B000
23188A005
05004A015
05004A087
05126A013
05916A171
05920A173
PUMP
14 24859C500
15 19101A019
16 14740A001
17 15760A510
18 19277A001
19 19100A029
20 19109A012
21 23188A002
22 25579A108
23 08728A006
24 25881A281
25 23188A001
EJECTOR BODY
SCREW (2 required)
HOSE CLAMP (2 required)
REGULATOR SWITCH
GASKET
PRESSURE GAUGE
REGULATOR
HOSE ADAPTER
BUSHING
BUSHING
SCREW (2 required)
NUT (2 required)
FITTING
PIPE TEE
PIPE NIPPLE
HOSE
EMBLEM
10 06190A001
11 25800A500
12 10649A120
13 11933A002
T.O.E. NIPPLE
TANK
NOZZLE
VENTURI TUBE
FITTING
TUBE
SHIM (2 required)
Water Ace Pump Co. • 1101 Myers Parkway • Ashland, OH 44805
7/95
23833A343
Download from Www.Somanuals.com. All Manuals Search And Download.
REVISION TO PARTS LIST
If a 1" x 1" regulator is used, the following parts will be
different than the parts list found in the jet tank system
installation manual.
If a 3/4" x 3/4" regulator is used, follow the replacement parts
list found in the jet tank system installation manual.
Ref.
No.
Replaced by
Description
Part Number
Part Number
Description
3/4" Regulator
1" Regulator
3
25443A000
05762A055
05004A016
05004A087
05916A191
25443A001
05762A009
05004A035
—
3/4" x 1" Elbow
1" Elbow
4
3/4" x 1/4" Reducer Bushing
3/4" x 1" Reducer Bushing
3/4" x 3" Nipple
1" x 1/4" Reducer Bushing
Not Required
5
6
1" x 3-1/2" Nipple
1/8"" Barbed Fitting
8
05427A250
23188A001
1/4" Barbed Fitting
21 23188A002
Retain these instructions for future reference.
Water Ace Pump Co. • 1101 Myers Parkway • Ashland, OH 44805
23833A343
7/95
Download from Www.Somanuals.com. All Manuals Search And Download.
|