Electric Pressure Fryer
MODELS FKM, FKM-F, & FKM-FC
Service Manual
Serial Numbers 137733 and higher
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Table of Contents........................................................................................................................................1
Introduction .................................................................................................................................................2
Safety Precautions....................................................................................................................................2
Safety Signs and Messages.................................................................................................................2
Specific Precautions.............................................................................................................................3
Equipotential ground plane ..............................................................................................................3
Full Disconnection............................................................................................................................3
Safe Work Practices.............................................................................................................................4
Safety Labels........................................................................................................................................8
Installation .................................................................................................................................................10
Operation ...................................................................................................................................................11
Controls and Indicators...........................................................................................................................11
Care of the Shortening............................................................................................................................14
FKM and FKM-F Operation ....................................................................................................................14
Start-Up (FKM and FKM-F)................................................................................................................14
Cooking (FKM and FKM-F) ................................................................................................................16
FKM-FC Operation .................................................................................................................................17
System Programming.........................................................................................................................17
Product Programming ........................................................................................................................19
Start-Up (FKM-FC) .............................................................................................................................22
Cooking (FKM-FC) .............................................................................................................................22
Maintenance ..............................................................................................................................................24
Replacement Parts....................................................................................................................................25
Assemblies..............................................................................................................................................25
Accessories.............................................................................................................................................43
Components............................................................................................................................................44
Wiring Diagrams........................................................................................................................................46
Notes ..........................................................................................................................................................56
Download from Www.Somanuals.com. All Manuals Search And Download.
Electric Pressure Fryer
Introduction
Introduction
The FKM Pressure Fryer is compact, attractive and functional in design. It is constructed of a stainless
steel fryer pot for cleaning ease. Exclusive BKI patented features and safety devices offer flexibility,
efficiency and reliability plus PERFECTION IN PRESSURE FRYING!
The BKI name and trademark on this unit assures you of the finest in design and engineering -- that it has
been built with care and dedication -- using the best materials available. Attention to the operating
instructions regarding proper installation, operation, and maintenance will result in long lasting
dependability to insure the highest profitable return on your investment.
PLEASE READ THIS ENTIRE MANUAL BEFORE OPERATING THE UNIT. If
you have any questions, please contact your BKI Distributor. If they are unable to
answer your questions, contact the BKI Technical Service Department, toll free:
1-800-927-6887. Outside the U.S., call 1-864-963-3471.
Safety Precautions
Always follow recommended safety precautions listed in this manual. Below is the safety alert symbol.
When you see this symbol on your equipment, be alert to the potential for personal injury or property
damage.
Safety Signs and Messages
The following Safety signs and messages are placed in this manual to provide instructions and identify
specific areas where potential hazards exist and special precautions should be taken. Know and
understand the meaning of these instructions, signs, and messages. Damage to the equipment, death or
serious injury to you or other persons may result if these messages are not followed.
This message indicates an imminently hazardous situation which, if not avoided,
will result in death or serious injury.
This message indicates a potentially hazardous situation, which, if not avoided,
could result in death or serious injury.
This message indicates a potentially hazardous situation, which, if not avoided,
may result in minor or moderate injury. It may also be used to alert against
unsafe practices.
This message is used when special information, instructions or identification are
required relating to procedures, equipment, tools, capacities and other special
data.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Electric Pressure Fryer
Introduction
Specific Precautions
Lids for FKM Pressure Fryers manufactured prior to May 27, 1980 (or units with
serial numbers lower than 3613) could be manually opened while under pressure
resulting in serious injury or death. If you have one of these units, please contact
the BKI Technical Services Department toll-free at 1-800-927-6887 for urgent
update information.
Risk of fire exists if the oil level drops below 5mm of the maximum oil level.
Use of oil/shortening older than the manufacturers recommendations for life of
the oil is prone to surge boiling and flash fires. Follow the oil manufacturers
guidelines for the life cycle of oil/shortening.
Do not open the drain valve or the fill valve while the fryer is under pressure.
Serious burns may result.
Follow instructions regarding effects of surge boiling of over-wet foods and
proper load size.
This unit incorporates components that contain Mercury. The use of Mercury
relays is an industry standard.
Equipotential ground plane
When a high current flows through a conductor, differences in potential appear
between the conductor and nearby metallic surfaces near the appliance. As a
result, sparks may be produced between the appliance and surrounding metal
surfaces. These sparks could cause serious injury, damage, or fire.
BKI provides an Equipotential ground terminal for the connection of a bonding
conductor after the installation of the appliance per lEC60417-1. This terminal is
located on the inside of the Power Entry Supply box near the Earth connection
and is marked with this symbol.
Full Disconnection
In accordance with Local and/or National wiring codes, the installer must provide
a means of full disconnection under over voltage Category III conditions. An IEC
approved cord and plug combination will meet this requirement.
Units not provided with a cord and plug do not meet this requirement. In
accordance with Local and/or National wiring codes, the installer must provide
the means of full disconnection.
The fryer is designed to hold a maximum of 75lbs (34KG) of oil/shortening.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Electric Pressure Fryer
Introduction
Safe Work Practices
Noncombustible Floors Only
Make sure your floor is noncombustible. Do not operate your fryer
on floors that are wood, carpeted or have rubber mats.
•
•
Placing your fryer on a combustible floor could cause a fire.
Serious injury could result.
Examples of noncombustible floors where you can safely
place your fryer are concrete, tile, and ceramic.
Keep The Area Around Your Fryer Uncluttered
Make sure to keep the area around your fryer clear of any
obstacles.
Serious injury can occur if you trip or fall near the fryer. You could
be burned by hot shortening that splashes out of the fryer or by
falling against the hot metal of the fryer.
Keep The Floor Around Your Fryer Clean Of Shortening
Make sure to keep the floor around your fryer clean of shortening
and other liquids.
Serious injury can occur if you slip near your fryer. You could be
burned by hot shortening that splashes out of the fryer or by falling
against the hot metal of the fryer.
Keep The Lid Closed When The Fryer Is Not In Use
Hot shortening can splash if someone moves the fryer or bumps
into it. Serious injury can occur if hot shortening splashes out of the
fryer.
Do not lean, sit or stand on the fryer or perform any maintenance or
cleaning duties while the fryer or the shortening is hot. You could
be burned.
Keep The Casters Locked
To avoid spilling shortening, keep the casters locked. If any
shortening spills near your fryer, clean it up immediately.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Electric Pressure Fryer
Introduction
Do Not Overfill The Fryer With Shortening
Hot shortening and steam may escape and burn you if you put too
much shortening in the fryer. Fill the fryer to approximately one inch
below the fill marks that are inside the fryer pot. Heat the
shortening. If needed, carefully add more shortening to bring the
level to the fill marks.
Do Not Let Any Water Get Into The Fryer
Always remove excess moisture from food before placing it into the
fryer basket. Water will cause the hot shortening to spatter. You
could be burned.
Do Not Overload The Basket With Food
Hot shortening and steam may escape and burn you if you place
too much food in the basket.
Always Make Sure The Lid Hook Is Latched When Closing The
Fryer
To make sure the lid hook is latched properly, press down the lid
until the hook snaps shut. Hot shortening and steam can escape if
the lid hook is not latched properly. You could be burned.
Keep Away From The Vent
Hot steam escapes from the vent continuously when you are using
your fryer. You could be burned if you get too close to the vent.
Seal The Safety Valve Properly
To seal the safety valve, lift the arm on the side of the valve. Then
release it. The valve should snap closed. Hot steam can escape
from the valve and you could be burned if you do not seal the valve
properly.
Always Tighten The Spin Handle When Closing The Fryer
Hot shortening and steam can escape if you do not tighten the spin
handle properly. You could be burned. Line up the orange knobs on
the fryer lid handle and the front hook when tightening.
Do Not Over-Tighten The Spin Handle
You could damage the fryer.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Electric Pressure Fryer
Introduction
Wear Safe Clothing Appropriate To Your Job
Always wear your insulated mitts when handling the fryer basket or
touch any hot metal surfaces. You received a pair of insulated mitts
with your fryer. If you lose or damage your mitts, you can buy new
ones at your local restaurant equipment supply store or from your
local BKI Distributor.
Always wear non-skid shoes when working around the fryer or any
other equipment that uses shortening. Never wear loose clothing
such as neckties or scarves while operating your fryer. Keep loose
hair tied back or in a hair net while operating your fryer.
Always wear appropriate personal protection equipment during the
filtering process to guard against possible injury from hot oil.
Always wear appropriate personal protection equipment during the
boil-out process to guard against possible injury from hot cleaning
solution.
Never Loosen The Spin Handle Until The Pressure Gauge Is At
Zero
Steam may escape suddenly if you loosen the spin handle before
the gauge is at zero. If steam escapes suddenly, you could be
burned.
After the pressure gauge is at zero, wait 5 seconds. Then loosen
the spin handle slowly to open the lid of the fryer. By doing this, the
steam will escape slowly and there is less change of being burned.
Always use extreme caution when working around the fryer with the
lid open.
Keep this manual with the Equipment
This manual is an important part of your equipment. Always keep it
near for easy access.
If you need to replace this manual, contact:
BKI
Technical Services Department
P.O. Box 80400
Simpsonville, S.C. 29680-0400
Or call toll free: 1-800-927-6887
Outside the U.S., call 864-963-3471
Protect Children
Keep children away from this equipment. Children may not
understand that this equipment is dangerous for them and others.
NEVER allow children to play near or operate your equipment.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Electric Pressure Fryer
Introduction
Keep Safety Labels Clean and in Good Condition
Do not remove or cover any safety labels on your equipment. Keep
all safety labels clean and in good condition. Replace any damaged
or missing safety labels. Refer to the Safety Labels section for
illustration and location of safety labels on this unit.
If you need a new safety label, obtain the number of the specific
label illustrated on page 8, then contact:
BKI
Technical Services Department
P.O. Box 80400
Simpsonville, S.C. 29680-0400
Or call toll free: 1-800-927-6887
Outside the U.S., call 864-963-3471
Be Prepared for Emergencies
Be prepared for fires, injuries, or other emergencies.
Keep a first aid kit and a fire extinguisher near the equipment. You
must use a 40-pound Type BC fire extinguisher and keep it within
25 feet of your equipment.
Keep emergency numbers for doctors, ambulance services,
hospitals, and the fire department near your telephone.
Know your responsibilities as an Employer
• Make certain your employees know how to operate the
equipment.
• Make certain your employees are aware of the safety
precautions on the equipment and in this manual.
• Make certain that you have thoroughly trained your employees
about operating the equipment safely.
• Make certain the equipment is in proper working condition. If you
make unauthorized modifications to the equipment, you will
reduce the function and safety of the equipment.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Electric Pressure Fryer
Introduction
Safety Labels
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Electric Pressure Fryer
Introduction
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Electric Pressure Fryer
Installation
Installation
For installation information refer to Electric Pressure Fryer, MODELS FKM, FKM-F, & FKM-FC,
Installation and Operation Manual LI0102.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Electric Pressure Fryer
Operation
Operation
Controls and Indicators
Refer to the figure and table below for an explanation of the fryer’s controls and indicators.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Electric Pressure Fryer
Operation
Item #
Description
Function
1
2
Spin Handle
Used to tighten the lid to the pot once it is latched.
Pop Safety Valve lever Used to release pressure periodically to prevent the seat from
sticking.
3
4
Pressure Gauge
Computer
Indicates the pressure inside the pot.
Used to program the cooking computer and activate the
programs.
5
Rocker Switch
FILTER – When placed in this position, power is applied to the
motor and shorting is pumped into the pot directly or thru the fill
hose.
OFF – When placed in this position, power is removed from both
the pump motor and heating elements.
FRY – When placed in this position, power is supplied to the
thermostat and heating elements.
6
7
8
Thermostat Knob
Thermostat Light
Digital Timer
Used to set the temperature of the shortening.
Illuminates red indicating that the heating elements are activated.
The digital timer consists of an LED, display, beeper and 8
buttons described below:
LED indicator
Prior to the start of a timing cycle the LED will be OFF. When
running a timing cycle the LED will flash. At the end of a timing
cycle the LED will turn ON steady. When idle the LED is off.
TIME SELECT (2
arrow buttons)
Two arrow buttons on the front panel are used to set the time.
Hold the UP ARROW button down to increase the time. The
longer the button is held down, the faster the rate at which the
time will increase. The DOWN ARROW button is used in the
same manner as the UP ARROW button except it will cause the
time to decrease. The time is increased or decreased in 30-
second increments.
START/STOP
button
Starting the Timer - Pressing this button while the timer is not
active will cause the timer to begin counting down the time on the
display.
Stopping the Timer - Pressing this button while the timer is
active will stop the timer from counting down and display the
remaining time. Time cannot be changed with the TIME SELECT
buttons at this point. If this button is pressed again the timer will
continue counting down from the point it was stopped.
Resetting the Timer - Pressing and holding this button for longer
than two (2) seconds will reset the timer and the display will return
to the original starting time. At this point, time can be changed
using the TIME SELECT buttons or the preset buttons.
Canceling The STIR OIL Function - Pressing this button cancels
the STIR OIL function while it is active.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Electric Pressure Fryer
Operation
Item #
Description
Function
8
ALARM button
This button allows the user to set an elapsed time at which the
internal alarm will sound during a cycle. The time is set by
pressing and holding the ALARM button while using the UP and
DOWN arrows to change the time. The controller will limit the
alarm time to be less than the currently programmed interval cycle
time. The default alarm time is 0:00 which disables it. The ALARM
time is saved on power down in the same manner as the last
interval time. When a time cycle is running and the alarm time has
elapsed the internal alarm will sound for 10 seconds. For
example, a cycle time 10:00 and alarm time of 2:00 would cause
the alarm to sound for 10 seconds once the controller has counted
down from 10:00 to 8:00. This button is used to cancel the STIR
OIL alarm. This button is also used to reconfigure the STIR OIL
Function.
A, B, C, D preset
buttons
These buttons are used to save and recall preset cycle and alarm
times, saving operator time and minimizing error when changing
interval cycle times and alarm times. To save the current interval
and alarm times into one of the preset locations, press and hold
the A, B, C, or D preset button for 2 seconds and the controller will
double chirp to indicate the times have been saved. To recall any
preset time, press and quickly release the appropriate button and
the time values are loaded and displayed. These buttons are also
used to reconfigure the STIR OIL function.
Beeper
Display
A beeper sounds when the timer counts down to 0. Pressing the
START/STOP button stops the beeper and resets the timer
causing the display to return to the original starting time. At this
point, time can be changed using the TIME SELECT buttons or
the preset buttons. The beeper will also sound for 10 seconds if
the alarm time has elapsed during a timing cycle. When the STIR
OIL function begins the beeper will sound until the ALARM or
START/STOP button is pressed.
Used to display the time. It also displays the words “STIR” then
“OIL” in .5 second intervals until the ALARM or START/STOP
button is pressed.
9
High Limit Reset
Switch
Located under the control panel. If the heating elements inside the
pot reach an unsafe temperature, power is automatically removed
from the control panel and elements. Pressing this switch returns
power to the control panel and elements.
10
Drain Lever
Fill Lever
DRAIN OPEN – When placed in this position, the drain valve
opens and shortening in the pot drains into the vat. Also power is
removed from the control panel and elements.
DRAIN CLOSED – When placed in this position, the drain valve is
closed to prevent shortening from draining into the pot.
11
FILL THRU POT – When placed in this position, shortening can
be pumped automatically from the vat to the pot if the rocker
switch is in the FILTER position.
FILL THRU HOSE – When placed in this position, shortening can
be pumped from the vat to the pot via a connected hose if the
rocker switch is in the FILTER position.
12
13
Rinse Hose Connector Used to connect the Rinse hose for cleaning and refilling the pot.
Pump Motor Reset
Switch
If the motor overheats while filtering, it will automatically shut off.
Wait 15 minutes to allow motor to cool before pressing this switch.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Electric Pressure Fryer
Operation
Care of the Shortening
Solid shortening should always be returned to the filter vat while in the liquid state. If this is not done, it
will have to be heated to a liquid state. When using solid shortening, the fryer must be equipped with a
pump heater. After filtering with solid shortening, the filter lines must be completely emptied of shortening.
The pump heater will take care of any residual shortening in the pump, but cannot melt all of the
shortening in the filter lines. The pump heater accessory may be purchased separately from BKI.
To extend the life of your shortening, for the best possible flavor in your products, and for economy and
efficiency of operation, we urge you to follow these recommendations:
1. Use only high-quality frying shortening without additives, of low moisture content and with a high
smoke point.
2. Press excess moisture from products before breading. The more moisture released in the
shortening, the quicker it will break down.
3. Filter at least once a day or once every three loads during frequent cooking.
4. Clean any residue or crust formations from the sides and bottom of the pot each time you filter
the shortening.
5. Add fresh shortening as needed to maintain the proper shortening level TO THE FILL MARK ON
THE POT WALL.
6. DO NOT HOLD SHORTENING AT HIGH TEMPERATURE when the fryer is not in use. If you
expect an elapsed time of one hour or more between cooking, close the lid and press the “0”
button on the FKM-FC model. On Models FKM and FKM-F, set the thermostat to 150º F.
7. Shortening changes are determined by the quantity and type of food prepared. Excessive boiling
and foaming are definite signs of shortening breakdown.
8. After you have finished frying for the day, filter the shortening and replace the filter pad. Also,
thoroughly clean the pot of sediment and crumbs and empty the condensate pan.
FKM and FKM-F Operation
Start-Up (FKM and FKM-F)
1. Make sure the main drain valve is closed.
2. Fill pot with shortening to about one inch below the fill mark.
Risk of fire exists if the oil level drops below the minimum oil level. The level of oil
within the pot must not fall below 5mm of the maximum oil level.
Use of oil/shortening older than the manufacturers recommendations for life of
the oil is prone to surge boiling and flash fires. Follow the oil manufacturers
guidelines for lifecycle of oil/shortening.
Overfilling the fryer pot with shortening could lead to serious injury. Ensure that
the fryer pot is filled with shortening only to the fill mark when shortening is hot.
Do not use any shortening other than what is specified in this manual and do not
overfill the fryer pot.
The FKM/FKM-F fryer has a maximum temperature setting of 375º F (190º C).
Do not use oil/shortening with a flashpoint less than 554º F (290º C)
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Electric Pressure Fryer
Operation
Use only high-quality shortening that has low moisture content, a high smoke
point and no additives.
3. The digital timer has a STIR OIL function that operates in one of four reconfigurable modes. If the
timer needs to be reconfigured, follow step a. If the timer does not need to be reconfigured, follow
step b.
a. Press and hold the ALARM button and at the same time place the FILTER/OFF/FRY switch
in the FRY position. The display will show the word “STIR” until the ALARM button is
released. When the button is release the display will show the current configuration mode. To
change this mode select the timer key that represents the mode you want. Refer to the table
below:
KEY
DISPLAY
MODE DESCRIPTION
New or unchanged timer. Alarm sounds at the end of the internal 6
minute countdown.
A
-AL-
Defeats the STIR OIL function. Timer operates as if it had no STIR
OIL function.
B
-OFF
C
D
PrES
LiFT
STIR OIL function for all Pressure Fryers.
STIR OIL function for all Autolift Fryers.
The display will now show the selected mode. Proceed to step c.
b. Once the fryer is filled with shortening, place the FILTER/OFF/FRY switch in the FRY
position.
c. Unless the STIR OIL function is operating in the –OFF mode, the digital timer activates a
STIR OIL function and begins an internal six minute countdown (not displayed). At the end of
the internal countdown, the display shows the words “STIR” then “OIL” in .5 second intervals
and the alarm sounds. Depress the ALARM button and stir the shortening freely while it is
heating.
IMPORTANT! Before the first cooking operation each day, stir the shortening freely while it is
heating to provide a balanced shortening temperature for excellent results with the first
cooking. Failure to do this can result in a crusty skin on the product surface with an
undercooked product internally. In addition, in some cases, failure to stir the shortening while
it is initially heating may cause the HI-LIMIT safety device to disable the power due to a false
overtemperature condition.
4. Set the thermostat to the desired cook temperature. The temperature light will go on. When the
temperature is reached, the light will go off. The light will continue to cycle on and off as the fryer
maintains the set temperature.
5. Press and hold the TIME SELECT arrow buttons on the digital timer until the desired cook time is
displayed or recall a preset time by quickly pressing the appropriate preset button.
6. The shortening will heat and begin to reach the fill mark inside the pot. Add more shortening as
required to reach the fill mark.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Electric Pressure Fryer
Operation
Cooking (FKM and FKM-F)
Do not open the drain valve or the fill valve while the fryer is under pressure.
Serious burns may result.
1. Ensure that the Start-Up procedures have been performed.
2. When frying chicken, lower the basket into the shortening in the fryer pot.
Hot shortening may splash out of the pot causing severe injury when dropping
chicken into pot. Carefully drop pieces of chicken into pot to prevent shortening
splashes.
3. Carefully drop the chicken in the shortening one piece at a time starting with thighs and
drumsticks. The fryer is designed to accommodate 48-50 pieces of chicken.
Failure to use the insulated mitts will result in severe injury. Always use the
insulated mitts when handling the hot fry basket.
4. Lift the basket and shake it. This keeps the food from sticking together and causing white spots
on the cooked food.
Hot shortening may splash out of the pot causing severe injury when lowering
basket into pot. Carefully lower basket into pot to prevent shortening splashes.
5. Slowly lower the fryer basket into fryer pot.
6. Close the lid. Make sure the lid snaps shut. Make sure the lid hook latches securely under the
catch.
7. Tighten the spin handle until the lid is firmly sealed. Then line up the orange knob on the spin
handle with the orange knob at the front of the fryer.
8. Activate the timer by pressing the START/STOP button on the digital timer. The timer will begin
the count down.
9. At the end of the frying cycle, the digital timer beeper will sound and the fryer will automatically
release pressure into the baffle box. Press the START/STOP button.
10. When the pointer on the pressure gauge is at zero, wait 5 seconds then slowly turn the spin
handle counterclockwise to break the seal around the lid. The fryer has a locking pin that
prevents turning the spin handle until the pressure drops to zero. Do not force the spin handle to
open the lid.
11. Slowly open the lid.
Failure to use the insulated mitts will result in injury. Always use the insulated
mitts when handling the hot fry basket.
12. Lift the basket and hang it on the front of the fryer pot to drain.
13. Empty the basket.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Electric Pressure Fryer
Operation
14. Remember to filter the shortening at least every third frying cycle load. Refer to the procedure in
this manual. Also filter the shortening and clean the fryer at the end of each day. If you do not
plan to use the fryer for an hour or more, turn the thermostat down to 150 and close the lid.
15. When you have finished frying for the day, turn the FILTER/OFF/FRY switch to the OFF position.
FKM-FC Operation
System Programming
Use the following figure and table to set options that apply to each product programs.
Figure 1. System Programming Sequence
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Electric Pressure Fryer
Operation
Table 1. System Programming Procedure
STEP
ACTION
Press the FILTER/OFF/FRY
DISPLAY
COMMENTS
1
LOW
switch to FRY.
2
3
4
Press PROG on the keypad.
Input 1712 and ENTER.
Press ENTER.
PROGRAM CODE
PROGRAM SYSTEM
PROGRAM DEGREES This command allows you
to choose the temperature
scale option you want to
use. The display will show
either show °F or °C.
°F
5
6
Press TOGGLE/CLEAR until the
desired option is displayed.
PROGRAM DEGREES X refers to the
temperature scale you
have chosen.
X
Press ENTER.
PROGRAM APL TYPE This command allows you
ELECTRIC to choose the appliance
type you are using. The
display may show
ELECTRIC, GAS OR ALF.
7
8
Press TOGGLE/CLEAR until the
desired option is displayed.
PROGRAM APL TYPE X refers to the appliance
X
type you have chosen.
Press ENTER.
PROGRAM MELTCYCL This command allows you
YES to set the melt cycle
option. This is normally set
to yes if you are using
solid shortening. The
display will show either
YES or NO.
9
Press TOGGLE/CLEAR until the
desired option is displayed.
PROGRAM MELTCYCL X refers to the melt cycle
X
option chosen.
10
Press ENTER.
PROGRAM GLBLFLTR This command allows you
0
to specify the total number
of fry cycles to complete
among all product
programs before a
message is displayed
reminding you to filter the
shortening (filter lockout).
11
Press TOGGLE/CLEAR and
input the number of fry cycles
you want to complete among all
product programs before
PROGRAM GLBLFLTR X refers to the number of
X
program cycles you want
to complete among all
product programs before
filtering the shortening.
enabling filter lockout.
12
13
Press ENTER.
PROGRAM SYSTEM
LOW
Press PROG to exit the
programming mode.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Electric Pressure Fryer
Operation
Product Programming
Use the following figure and table to set a maximum of eight product programs. The product programs
must be set before cooking can begin.
Figure 2. Product Programming Sequence
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Electric Pressure Fryer
Operation
Table 2. Product Programming Procedure
STEP
ACTION
Press the FILTER/OFF/FRY
DISPLAY
COMMENTS
1
LOW
switch to FRY.
2
3
4
Press PROG on the keypad.
Input 1724 and press ENTER.
PROGRAM CODE
PROGRAM PRODUCT #
Select the program product
number (1-8).
PROGRAM PRODUCT X X refers to the program
number you selected.
5
Press ENTER.
PROGRAM TIME1 This command allows you
00:00 to specify the cooking time
for this stage. The time
displayed may be a
previously programmed
value.
6
7
Press TOGGLE/CLEAR and
input the number of minutes you
want to cook.
PROGRAM TIME1 XX:XX refers to the
XX:XX number of minutes you
input.
Press ENTER.
PROGRAM TEMP1 This command allows you
to specify the cooking
temperature for this stage.
The temperature displayed
may be a previously
000 °F
programmed temperature.
The temperature scale
may also display °C
depending on the system
option that is set.
8
9
Press TOGGLE/CLEAR and
input the cooking temperature for
product to be cooked.
PROGRAM TEMP1 XXX refers to the cooking
temperature you input.
XXX °F
Press ENTER.
PROGRAM TEMPCOM1 This command enables
FLEX TIME you to select whether or
not time is allowed for the
fryer to recover from
temperature loss while
cooking during this stage.
The FLEX TIME option will
allow the fryer to recover
from temperature loss.
10
11
Press TOGGLE/CLEAR until the
desired option is displayed.
PROGRAM TEMPCOM1 X refers to the
X
temperature compensation
option selected.
Press ENTER.
PROGRAM VALVE1 This command allows you
CLOSED to specify whether the
solenoid valve will be open
or closed during this
stage.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Electric Pressure Fryer
Operation
STEP
12
ACTION
DISPLAY
COMMENTS
Press TOGGLE/CLEAR until the
desired option is displayed.
PROGRAM VALVE1 X refers to the solenoid
X
valve option selected.
OPEN is used for Models
ALF and BLF Automatic
Lift fryers. If your program
requires the solenoid valve
to be closed while
cooking, choose the
CLOSED option.
13
14
Repeat steps 5-12 when
programming stages 2, 3, 4 and
5 for Electric and Gas appliance
types.
The time and temperature
of each stage has to be
less than the preceding
stage.
Repeat steps 5-10 when
programming stages 2, 3, 4 and
5 for an ALF appliance type.
Press ENTER.
PROGRAM PREALARM This command allows you
00:00 to specify the number of
minutes before the end of
the cooking time (for each
stage) until the alarm
sound The prealarm value
displayed may be a
previously programmed
value.
15
16
Press TOGGLE/CLEAR and
input the prealarm minutes.
PROGRAM PREALARM XX:XX refers to the
XX:XX prealarm minutes you
input.
Press ENTER.
PROGRAM FILTER This command allows you
0
to specify the number of
fry cycles you want to
complete for this program
before a message is
displayed reminding you to
filter the shortening (filter
lockout). The filter value
displayed may be a
previously programmed
value.
17
Press TOGGLE/CLEAR and
input the number of fry cycles
you want to complete before
enabling filter lockout.
PROGRAM FILTER X refers to the number of
X
program cycles you want
to complete before filtering
the shortening.
18
19
Press ENTER.
PROGRAM PRODUCT #
If you wish to input more
programs, proceed by pressing
the next program number and
follow steps 5 through 18 or
press PROG to exit the
programming mode.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Electric Pressure Fryer
Operation
Start-Up (FKM-FC)
1. Make sure the main drain valve is closed.
2. Fill pot with shortening to about one inch below the mark.
Risk of fire exists if the oil level drops below the minimum oil level. The level of oil
within the pot must not fall below 5mm of the maximum oil level.
Use of oil/shortening older than the manufacturers recommendations for life of
the oil is prone to surge boiling and flash fires. Follow the oil manufacturers
guidelines for lifecycle of oil/shortening.
Overfilling the fryer pot with shortening could lead to serious injury. Ensure that
the fryer pot is filled with shortening only to the fill mark when shortening is hot.
Do not use any shortening other than what is specified in this manual and do not
overfill the fryer pot.
The FKM-FC fryer has a maximum temperature setting of 390º F (200º C). Do
not use oil/shortening with a flashpoint less than 554º F (290º C)
Use only high-quality shortening that has low moisture content, a high smoke
point and no additives.
3. Place the FILTER/OFF/FRY switch to the FRY position. The question “Is the Fry Pot filled – If yes
press ENTER” will appear on the computer display. The shortening will heat and begin to reach
the fill mark inside the pot.
4. Add more shortening as required to reach the fill mark. Once the oil reaches the fill mark, press
the ENTER button. The computer will display “STIR OIL” and automatically enter the STIR OIL
mode. In this mode the computer will heat the oil to 255°F and hold that temperature.
5. Stir the oil freely while it is heating. Press the 0 button when finished stirring the oil.
IMPORTANT! Before the first cooking operation each day, stir the shortening freely while it is
heating to provide a balanced shortening temperature for excellent results with the first cooking.
Failure to do this can result in a crusty skin on the product surface with an undercooked product
internally. In addition, in some cases, failure to stir the shortening while it is initially heating may
cause the HI-LIMIT safety device to disable the power due to a false overtemperature condition.
Cooking (FKM-FC)
Do not open the drain valve or the fill valve while the fryer is under pressure.
Serious burns may result.
1. Ensure that the Start-Up procedures have been performed.
2. Press the desired program number on the keypad. The computer will still display "LOW". The
fryer will begin to heat to the temperature that has been factory preset. When "READY" appears
on the display, the fryer is up to the desired temperature and the product can be loaded.
3. When frying chicken, lower the basket into the shortening in the Fryer pot.
Hot shortening may splash out of the pot causing severe injury when dropping
chicken into pot. Carefully drop pieces of chicken into pot to prevent shortening
splashes.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Electric Pressure Fryer
Operation
4. Carefully drop the chicken in the shortening one piece at a time starting with thighs and
drumsticks. The fryer is designed to accommodate 48-50 pieces of chicken.
Failure to use the insulated mitts will result in severe injury. Always use the
insulated mitts when handling the hot fry basket.
5. Lift the basket and shake it. This keeps the food from sticking together and causing white spots
on the cooked food.
Hot shortening may splash out of the pot causing severe injury when lowering
basket into pot. Carefully lower basket into pot to prevent shortening splashes.
6. Slowly lower the fryer basket into fryer pot.
7. Close the lid. Make sure the lid snaps shut. Make sure the lid hook latches securely under the
catch.
8. Tighten the spin handle until the lid is firmly sealed. Then line up the orange knob on the spin
handle with the orange knob at the front of the fryer.
9. Press the desired program number a second time. The red light above the program number will
flash and the computer will display “COOK”. This will start a countdown in minutes and seconds
until the end of the cycle.
10. At the end of the cooking cycle, the computer will display "DONE" and signal with a series of
audible "beeps". Press the selected number once again to stop the cook cycle. Fifteen seconds
before the end of the cook cycle, the program will automatically release the pressure from the
fryer. For your safety, the lid will not unlock, even at the end of the cook cycle, until the pressure
has been fully released.
Hot steam will escape when you open the lid possibly causing severe injury.
Keep your face and arms away from the fry pot.
11. Slowly turn the spin handle counterclockwise to break the seal around the lid. Your fryer has a
locking pin that prevents turning the spin handle until the pressure drops to "0".
12. Slowly open the lid.
Failure to use the insulated mitts will result in injury. Always use the insulated
mitts when handling the hot fry basket.
13. Lift the basket and hang it on the front of the fryer pot to drain.
14. Empty the basket.
15. Remember to filter the shortening at least every third frying cycle load. Refer to the procedure in
this manual. Also filter the shortening and clean the fryer at the end of each day.
16. Close the lid and press the 0 button. Idle 255°F will display. This will automatically hold the
shortening at a cooler temperature.
17. To escape the idle mode, press the 0 button again and the fryer will heat to its original
temperature.
18. When you have finished frying for the day, turn the FILTER/OFF/FRY switch to the OFF position.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Electric Pressure Fryer
Maintenance
Maintenance
For maintenance information refer to Electric Pressure Fryer, MODELS FKM, FKM-F, & FKM-FC,
Installation and Operation Manual LI0102.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Electric Pressure Fryer
Replacement Parts
Replacement Parts
Use the information in this section to identify replacement parts. To order replacement parts, call your
local BKI sales and service representative. Before calling, please note the serial number, model number
and voltage on the rating tag affixed to the unit.
Assemblies
Description
Assembly #
AN19104100
SB1910
Figure #
Figure 3
Figure 4
Figure 5
Figure 6
Figure 7
Table #
Table 3
Table 4
Table 5
Table 6
Table 7
DEAD WEIGHT ASSEMBLY
DOOR ASSEMBLY
DRAIN/MOTOR/PIPING ASSEMBLY
DRAIN VALVE & PLUGS
N/A
SB1999S
DOMESTIC FRONT PANEL FKM/FKM-F
EUROPEAN FRONT PANEL FKM/FKM-F
AN19108100
AN19108200
FRONT PANEL FKM-FC
LID/TOP ASSEMBLY
AN19106400
SB1992S
Figure 8
Figure 9
Figure 10
Figure 11
Table 8
Table 9
Table 10
Table 11
OIL VAT ASSEMBLY
AN16010200
QUICK DISCONNECT ASSEMBLY
AN19103300
SB1997S
DOMESTIC REAR PANEL FKM/FKM-F
EUROPEAN REAR PANEL FKM/FKM-F
AN19106100
AN19106500
Figure 12
Table 12
REAR PANEL FKM-FC
SOLENOID VALVE
AN19106200
AN19104300
Figure 13
Figure 14
Table 13
Table 14
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Electric Pressure Fryer
Replacement Parts
Figure 3. Dead Weight Assembly
Table 3. Dead Weight Assembly Parts
ITEM #
1
2
3
4
5
6
7
8
PART #
QTY
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
DESCRIPTION
PIPE, POPOFF VALVE BAFF BOX
PIPE, DEAD WT TO BAFFLE BOX
ORIFICE, SS
FT0395
FT0396
O0001
O0002
PV0001
FT0066
FT0235
FT0190
FT0084
FT0563
FT0067
FT0234
C0657
GASKET, O-RING #2-222
VALVE, POP SAFETY 1321148
ELL, REDUCER 3/4 X 1/2 90 DEG
NIPPLE, 1/2 X C SS
ELL, STREET 1/4 90 DEG CP
COUPLING, BRASS 1/4
FITTING, COMPRESSION ¾”
BUSHING, C110JO 3/4 X 1/2 CP
NIPPLE, 1/4 X 1 1/2 SS 304
COVER, DEAD WEIGHT VALVE FKM
BODY, DEAD WEIGHT VALVE FKM
WEIGHT, VALVE FKM 12#
GAUGE, PRESSURE 30 PSI
9
10
11
12
13
14
15
16
B0969
W0201
G0064
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Electric Pressure Fryer
Replacement Parts
Figure 4. Door Assembly
Table 4. Door Assembly Parts
ITEM #
PART #
QTY
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
F0083
ST0013
H0010
N0059
N0165
N0527
N0175
N0176
P0022
RIV172
SB1951
SCR008
SCR383
WFKMA178
N0153
2
1
2
1
1
1
1
1
1
3
1
6
2
1
1
1
THREAD INSERT 10-24 STEEL
BRACKET, BRUSH HOLDER FKM, LPF,LGF
HINGE, LH PIN HALF
DECAL, SMALL BRUSH/
DECAL, NOTICE LOST MANUAL
DECAL, SAFETY INSTR FRYERS
DECAL, SLIPPING ADMONITIONS
DECAL, INSTR & SAFETY MANUAL
HANDLE, PULL SS P60-1010
RIVET, 1/8 X 1/4 CS PLT POP
INSIDE DOOR POCKET/MAGNET WELD FKM
SCREW, 10 X 1/2 PHIL TRUSS HD
SCREW, 10-24 X 1/2" PHIL TRUSS HD
DOOR, FRYER OUTSIDE WELD
DECAL, FKM WARNING ACME SCREW
HINGE, DOOR,RH,PIN SIDE FRY.DOORS
H0009
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Electric Pressure Fryer
Replacement Parts
Figure 5. Drain/Motor/Piping Assembly
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Electric Pressure Fryer
Replacement Parts
Table 5. Drain/Motor/Piping Assembly Parts
ITEM #
1
2
3
4
5
6
7
8
PART #
QTY
1
1
2
1
1
1
3
1
1
1
1
2
1
1
2
2
2
1
1
1
1
1
2
1
1
3
1
1
1
1
1
1
1
DESCRIPTION
DRAIN VALVE REPLACEMENT
ELL, STREET 3/8 90 DEG BLACK
NIPPLE, 3/8 NPT X 1 1/2 SCH 40
BALL VALVE ASSY, FRYERS
TEE, 1/2 X 1/2 X 3/8 BLK
CONNECTOR, MALE 10FBU-S NKL PLTD
COUPLING, 5/8 45¦ FLARE TO
DRAIN VALVE BRACKET, FRYERS
TUBING, 29" 1/2" ID
MB19101000
FT0044
FT0412
SB1314
FT0538
FT0507
FT0536
FT0543
TU0206
TU0205
P0070
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
TUBING, 12" 1/2" ID
PUMP ONLY FOR HAIGHT MOTOR
PIN, COTTER HAIRPIN #213
PIN, CLEVIS 3/16 X 1-1/4
PIN, CLEVIS 3/16 X 1 3/4
SPACER, ALUM .5 X .125
F0254
F0255
F0253
SP0014
SP0034
NUT253
F0158
LZ0130
S0054
H0089
N0285
SCR194
H0215
C0672
SPACER, DRAIN VALVE BRKT FRYERS
NUT, 6-32 S/S 18-8 NYLON
BUSHING, BLK 1/2 HEYCO SNAP
SWITCH,ACT. COVER FKMA247
SWITCH, MICRO BZ-2RW822-A2
HANDLE SUPPORT PLATE
DECAL, FKM-F DRAIN HNDL PLATE
SCREW, 6-32 X 1 SL RD HD MS
HANDLE, DRAIN VALVE FKM BLF
COVER, DRAIN HANDLE RED
SCREW, 8 X 1/2 PHIL PAN HEAD
FILL VALVE HANDLE, FRYERS
COVER, FILL HANDLE BLACK
PLUG, F-H4F4-7-7 QUIK DISCONN
BUSHING, BLK HEX REDUCING
TUBING, TEE TO DISCONNECT
ELL, STREET 1/2 90 DEG BLACK
MOTOR, LEESON LESS CORD/PUMP
SCR006
MA19100508
C0668
P0081
B0851
MA19100800
FT0132
M0053
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Electric Pressure Fryer
Replacement Parts
Figure 6. Drain Valve & Plugs
Table 6. Drain Valve & Plugs Parts
ITEM #
PART #
QTY
DESCRIPTION
1
2
MB19101000
FT0243
1
2
DRAIN VALVE REPLACEMENT
PLUG, 3/8" SQ HEAD PIPE
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Electric Pressure Fryer
Replacement Parts
Figure 7. Domestic/European Front Panel FKM/FKM-F
Table 7. Domestic/European Front Panel FKM/FKM-F Parts
ITEM #
PART #
QTY
DESCRIPTION
DECAL, CTL PNL FKM FKMF
SWITCH, RKR DPDT 15A 250V LAMP
TIMER, 230V DIGITAL 4 BUTTON
PILOT LIGHT, ROUND 250V
1
2
3
4
5
6
N0522
S0104
TI0032
PL0004
T0075
K0040
1
1
1
1
1
1
THERMOSTAT, SOLID STATE FRYER
KNOB, S/S STRAT T0075
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Electric Pressure Fryer
Replacement Parts
Figure 8. Front Panel FKM-FC
Table 8. Front Panel FKM-FC Domestic Parts
ITEM #
PART #
N0524
S0104
QTY
DESCRIPTION
DECAL,CTL PNL FKMFC
SWITCH, RKR DPDT 15A 250V LAMP
CONTROLLER, VFD LESS HARNESS
1
2
3
1
1
1
CP0039
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Electric Pressure Fryer
Replacement Parts
Figure 9. Lid/Top (sheet 1 of 4)
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Electric Pressure Fryer
Replacement Parts
Figure 9. Lid/Top (Sheet 2 of 4)
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Electric Pressure Fryer
Replacement Parts
Figure 9. Lid/Top (Sheet 3 of 4)
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Electric Pressure Fryer
Replacement Parts
Figure 9. Lid/Top (Sheet 4 of 4)
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Electric Pressure Fryer
Replacement Parts
Table 9. Lid/Top Parts
ITEM #
Figure 9 (sheet 1)
Figure 9 (sheet 2)
PART #
SB1992S
SB3481
QTY
DESCRIPTION
LID/TOP
1
3
2
1
1
1
1
1
1
1
1
1
2
1
2
2
1
2
2
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
2
2
1
1
1
1
1
1
1
HANDLE ASSY, SPIN
1
2
3
4
FT0332
K0003
K0020
K0043
AB19103900
A0120
H0155
P0094
H0024
K0043
STUD, 5.5” TIGHTEN DN HN
KNOB, BLACK #85C
HUB, TIGHTEN DOWN
KNOB, ORANGE
Figure 9 (sheet 3)
ARM ASSY, FKM
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
ARM COMPLETE FKM LGF
HANDLE, BLK DELRIN FKM LPF LGF
PIN, HOOK FKM, LPF, LGF
HOOK, LID 1018 ALLOY
KNOB, ORANGE
N0160
NUT128
S0091
DECAL, WARNING BEFORE USING
NUT, 5/16-18 SS 18-8 CAP
SPRING, HOOK LGF LPF FKM
SCREW, 1/4-20 X 1/2 FLAT HD
SCREW, 1/4-20 X 1/2 PHIL RD HD
BUSHING, BRONZE 1"
HANDLE SIDE FOR H0155 FKM LPF LGF
WASHER, 5/16 LOCK ZINC PLTD
WASHER, 1/4 INT LOCK
SCR122
SCR259
TB0020
H0156
WSH045
WSH102
FT0407
F0026
SB1989
F0353
G0016
S0155
B0857
PLUG, HOLE 3/8" SHORT PRONG
ROLL PIN, 5/32 X 3/4
Figure 9 (sheet 4)
LID LOCKING ASSY W/INSERT FKM
PIN, LOCKING FKM LGF LPF
GASKET, FKM LID BONDED SILICON
SPRING, LOCKING PIN W/LID INSERT
BUSHING, BRONZE 3/8X9/16X5/8
LID INSERT, FKM
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
P0115
FK0010
C0674 *
F0107
LID, FKM CAST ALUM
LID COVER AND ARM GUIDE FKM
LOCK KEY PIN, FRYERS
FKMA016
FKMA152
FKMA201
FT0049
N0153 *
N0345 *
SCR383
SCR176
SCR178
TB0021
TC0003
TC0005
TS0010
S0071
PIN, HINGE
KEY, TIGHTEN DOWN SCREW
PLATE, TIGHTEN DOWN FKM
COLLAR, 1/2" SET BRIGHT
DECAL, FKM WARNING ACME SCREW
DECAL, HOOK LID INSTRUCTIONS
SCREW, 10-24 X 1/2" PHIL TRUSS HD
SCREW, 8-32 X 3/8 SLOT BINDING
SCREW, 5/16-18 X 1 FLAT HD
TIGHTEN DOWN BASE COLD ROLLED
COLLAR, THREADED SHAFT
COLLAR, LOCKING RING
SCREW, TIGHTEN DOWN
SPRING, TORSION
PLATE, LID FOR LOCKING DEVICE
LZ0107
* - These parts constitute Lid Cover Assembly, AN1910840S.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Electric Pressure Fryer
Replacement Parts
Figure 10. Oil Vat Assembly
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Electric Pressure Fryer
Replacement Parts
Table 10. Oil Vat Assembly Parts
ITEM #
PART #
QTY
DESCRIPTION
AN16010300
SB1991
O0013
WB16010400
SB7659
FS0003
FS0002
FS0001
FC0004
1
1
1
1
1
1
1
1
1
1
1
1
1
FILTER SCREEN ASSY,FKM
1
2
3
4
5
6
7
8
9
QUIK DISCONNECT BRACKET WELDMENT
O-RING, FLUOROCARBON V680-70
FILTER VAT TUBE WELD, BLF
FILTER SCREEN FITTING SPOTWELD
FILTER SCREEN, TOP
FILTER SCREEN, INTERCEPTOR
FILTER SCREEN, BOTTOM
NUT SCREEN RETAINING FKM-F &
FILTER VAT WELD QUIK DISC
COVER, FILTER VAT
DECAL, VAT COVER SAFETY WARN
CRUMB BASKET WELD, LG VAT ASSY
WB16010600
FKMA357
N0395
10
11
12
SB7675
Figure 11. Quick Disconnect Assembly
Table 11. Quick Disconnect Assembly Parts
ITEM #
PART #
B0996
FT0429
FT0500
FT0536*
O0013
O0014
S0138
SCR4531*
QTY
DESCRIPTION
BALL, 11/16" STEEL BEARING
1
2
3
4
5
6
7
8
1
1
1
1
2
1
1
2
QUICK DISCONNECT, PUMP SIDE
QUICK DISCONNECT, VAT SIDE
COUPLING, 5/8 45¦ FLARE TO
O-RING, FLUOROCARBON V680-70
O-RING, PARKER #2-124 LARGE
SPRING, FOR QUICK DISCONNECT
SCREW, #10 24X3/8" WASHERED
* - Not included with SB1997S
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Electric Pressure Fryer
Replacement Parts
Figure 12. Domestic/European Rear Panel FKM/FKM-F
Table 12. Domestic/European Rear Panel FKM/FKM-F Parts
ITEM #
1
2
3
4
5
6
7
8
PART #
QTY
1
1
2
1
1
1
1
2
3
2
3
2
1
1
DESCRIPTION
THERMOSTAT, HI LIMIT 540 DEG
TERM BLOCK 4 CONDUCTOR CTR
TERM BLOCK 4 CONDUCTOR W/MTG FOOT
TERM BLOCK END PLATE
T0036
TB0064
TB0065
TB0068
TB0069
R0148
F0158
F0097
R0134
F0154
TERM BLOCK JUMPER BAR (not shown)
RELAY, 3 POLE 42CF35AG
BUSHING, BLK 1/2 HEYCO SNAP
FUSE, 15A 300V SC15 TIME DELAY
RELAY, MERCURY MDI 60NO220A
BUSHING, BLK 1-3/16 HEYCO SNAP
CLAMP, CABLE 3/16"
FUSE HOLDER, 15A 300V HPF-EE
CONNECTOR, BOX #7483 1"
PLUG, HOLE 7/8" (1/2" CONDUIT)
9
10
11
12
13
14
F0342
FH0001
FT0080
FT0277
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Electric Pressure Fryer
Replacement Parts
Figure 13. Rear Panel FKM-FC
Table 13. Rear Panel FKM-FC Parts
ITEM #
PART #
QTY
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
T0036
R0148
TB0064
TB0065
TB0068
R0134
W0054
TB0069
F0154
1
1
1
2
1
3
1
1
2
2
2
1
3
2
1
1
THERMOSTAT, HI LIMIT 540 DEG
RELAY, 3 POLE 42CF35AG
TERM BLOCK 4 CONDUCTOR CTR
TERM BLOCK 4 CONDUCTOR W/MTG FOOT
TERM BLOCK END PLATE
RELAY, MERCURY MDI 60NO220A
TRANSFORMER ASSY 240V
TERM BLOCK JUMPER BAR (not shown)
BUSHING, BLK 1-3/16 HEYCO SNAP
RELAY, X-40, SGL FRYER
FUSE, 15A 300V SC15 TIME DELAY
BUSHING, BLK 1/2 HEYCO SNAP
CLAMP, CABLE 3/16"
FUSE HOLDER, 15A 300V HPF-EE
CONNECTOR, BOX #7483 1"
R0044
F0097
F0158
F0342
FH0001
FT0080
FT0277
PLUG, HOLE 7/8" (1/2" CONDUIT)
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Electric Pressure Fryer
Replacement Parts
Figure 14. Solenoid Valve Assembly
Table 14. Solenoid Valve Assembly Parts
ITEM #
PART #
QTY
DESCRIPTION
CONNECTOR, 3/8 STR FLEX LIQUIDTITE
PIPE, DEAD WT TO BAFFLE BOX
VALVE, SOLENOID HV-214-761-2 240V
FITTING, COMPRESSION ¾”
1
2
3
4
FT0249
FT0396
SV0001
FT0563
1
1
1
1
42
Download from Www.Somanuals.com. All Manuals Search And Download.
Electric Pressure Fryer
Replacement Parts
Accessories
Description
Accessory #
B0114
B0075
B0063
B0051
B0049
B0052
SB7655
SB2332
SB7650
G0052
Figure #
Item #
BASKET, LARGE FKM BAIL HANDLE
BRUSH, DRAIN (LONG WHITE)
BRUSH, L TIPPED 40152
BRUSH, LONG #5702
BRUSH, POT SCRUBBER, WHITE
BRUSH, SHORT #6175
Figure 15
Figure 15
Figure 15
Figure 15
Figure 15
Figure 15
Figure 15
Figure 15
Figure 15
Figure 15
1
2
3
4
5
6
7
8
9
CORD SET, FKM-FC 7'
FILTER HOSE, FEMALE SOCKET
FILTER VAT DOLLY FKM-F
INSULATED MITT 13"
10
Figure 15. Accessories
1
2
5
8
3
6
9
4
7
10
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Electric Pressure Fryer
Replacement Parts
Components
Description
Component #
A0101
Figure #
Item #
1
ARM ADJUSTABLE STOP /FKM
BAFFLE BOX ASSEMBLY
BRACKET, CALROD FKMA258
CALROD, 208V 5675W FKM-F
CALROD, 240V 5675W FKM-F
CASTER, W/TOP PLATE 5"
CLAMP, HOSE #6207 #4
Figure 16
Figure 16
Figure 16
Figure 16
Figure 16
Figure 16
Figure 16
Figure 16
Figure 16
Figure 16
Figure 16
Figure 16
Figure 16
Figure 16
Figure 16
Figure 16
Figure 16
Figure 16
Figure 16
Figure 16
Figure 16
AN19102800
LZ0006
2
3
C0030
4
C0031
5
C0406
6
HF0009
7
COLLAR, 1/2" SET BRIGHT
CONDENSATION PAN WELDMENT
DRAIN PIPE, CONDENSATE FKM
FILTER, FKM-F 13.5 X 20.5
FT0049
8
WFKMA341
FKMA260
FI0007
9
10
11
12
13
14
15
16
17
18
19
20
21
OUTLET BOX, (ON FKM ONLY FOR POWERING FKF) SB1953
PROBE ASSEMBLY KIT, COMPUTER
SEMI AUTOMATIC HOSE ASSEMBLY (FKM only)
SIDE CABINET, L&R FKM/DNF
SB1938
SB1990
FKMA399
S0106
SLIDE, UHMW U-SHAPE .5 X 1/8ID
STRIKER PLATE (DOOR CATCH)
SWITCH, ACT. COVER FKMA247
THERMISTER PROBE/FTGS ASSEMBLY
BRACKET BACK PLATE FKMA259
FILTER BAG CLIP FKM-F
FKMA167
LZ0130
SB7656
LZ0007
ST0015
Figure 16. Components
1
2
3
4
5
6
44
Download from Www.Somanuals.com. All Manuals Search And Download.
Electric Pressure Fryer
Replacement Parts
7
8
9
10
13
16
19
11
14
17
20
12
15
18
21
45
Download from Www.Somanuals.com. All Manuals Search And Download.
Electric Pressure Fryer
Wiring Diagrams
Wiring Diagrams
Figure 17. FKM-F 208V/220V/240
M
46
Download from Www.Somanuals.com. All Manuals Search And Download.
Electric Pressure Fryer
Wiring Diagrams
Figure 18. FKM-F 220V/380V, 230V/400V, 240V/415V
M
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Electric Pressure Fryer
Wiring Diagrams
Figure 19. FKM-FC 208V/220V/240V (Sheet 1 of 4)
48
Download from Www.Somanuals.com. All Manuals Search And Download.
Electric Pressure Fryer
Wiring Diagrams
Figure 19. FKM-FC 208V/220V/240V (Sheet 2 of 4)
49
Download from Www.Somanuals.com. All Manuals Search And Download.
Electric Pressure Fryer
Wiring Diagrams
Figure 19. FKM-FC 208V/220V/240V (Sheet 3 of 4)
50
Download from Www.Somanuals.com. All Manuals Search And Download.
Electric Pressure Fryer
Wiring Diagrams
Figure 19. FKM-FC 208V/220V/240V (Sheet 4 of 4)
51
Download from Www.Somanuals.com. All Manuals Search And Download.
Electric Pressure Fryer
Wiring Diagrams
Figure 20. FKM-FC 220V/380V, 230V/400V, 240V/415V (Sheet 1 of 4)
52
Download from Www.Somanuals.com. All Manuals Search And Download.
Electric Pressure Fryer
Wiring Diagrams
Figure 20. FKM-FC 220V/380V, 230V/400V, 240V/415V (Sheet 2 of 4)
53
Download from Www.Somanuals.com. All Manuals Search And Download.
Electric Pressure Fryer
Wiring Diagrams
Figure 20. FKM-FC 220V/380V, 230V/400V, 240V/415V (Sheet 3 of 4)
54
Download from Www.Somanuals.com. All Manuals Search And Download.
Electric Pressure Fryer
Wiring Diagrams
Figure 20. FKM-FC 220V/380V, 230V/400V, 240V/415V (Sheet 4 of 4)
55
Download from Www.Somanuals.com. All Manuals Search And Download.
Electric Pressure Fryer
Notes
Notes
56
Download from Www.Somanuals.com. All Manuals Search And Download.
Electric Pressure Fryer
57
Download from Www.Somanuals.com. All Manuals Search And Download.
P.O. Box 80400, Simpsonville, S.C. 29680-0400, USA
Made and printed in the U.S.A
LI0192/0808
Download from Www.Somanuals.com. All Manuals Search And Download.
|
3Com Network Router External ISDN Modem User Manual
3M Computer Accessories ET 3250 55 User Manual
ADC Switch ICX 250 User Manual
Agilent Technologies Portable Generator 81250 User Manual
AKG Acoustics Microphone C 426B User Manual
Alpine CD Player CDE 9842 User Manual
Aspire Digital eBook Reader version 120 User Manual
Atlantis Land Switch A02 F48 4G User Manual
Atlona Car Video System AT DIS7 HD User Manual
BACtrack Automobile Accessories S75 User Manual